Motorcraft Oil Filter - Amazon S3...Motorcraft Oil Filter Construction Steel Case- Multiple flutes...
Transcript of Motorcraft Oil Filter - Amazon S3...Motorcraft Oil Filter Construction Steel Case- Multiple flutes...
Motorcraft Oil Filter
ConstructionSteel Case- Multiple flutes for easy removal
Efficient Filter Media
Pressure Relief / By-Pass Valve At Inlet
End cap seam is crimped and rolled securely
Corrugated Steel Center Tube
Anti-Drain-Back Valve–Heat Resistant Silicone
FL-820S
Protection For Today’’’’s Longer Service Intervals (FL-820S)
Motorcraft Features & Benefits
Motorcraft Oil Filters Aftermarket Oil Filters
Pressure Relief Valves
o Features up-front (threaded-end) pressure relief valve
design which prevents unfiltered oil from reaching the
engine
Anti-Drain Back Valveo Top selling Motorcraft oil filters utilize silicone rubber
anti-drain back valves for higher heat resistance
Center Tubes
o Corrugated steel center tubes that withstand pressure
surges and prevent leakage
Quality Constructiono Motorcraft filters have well-bonded end plates and
consistent pleat spacing
o High-quality steel case and base
Media Area
o Filter media is formulated to meet Ford OEM
requirements and media area is larger for optimal
efficiency and capacity
o Pleat number and height equate to more filtering surface
area and greater filtering capacity
Pressure Relief Valveso Many aftermarket filters use a dome-end design relief
valve which may allow unfiltered oil into the engine
Anti-Drain Back Valveo Many aftermarket anti-drain back valves are constructed
of nitrile rubber that can become brittle over time when
exposed to hot oil
Center Tubes
o Many aftermarket filters have plastic center tubes
Quality Constructiono Some aftermarket filters are not well bonded, allowing
unfiltered bypass
o Some aftermarket filters may use lower-quality steel case
Media Areao Aftermarket filter media is not designed to meet Ford's
requirements and the media area is typically smaller
FL-820S
Typical Oil Filter
Alignment on Engine
Motorcraft Design Advantages
Aftermarket
Sludge build up
Open Pressure Relief / By-pass Valve
Oil flow to engine
Oil flow to engine
Sludge picked up in oil
FL-820S
Features/Benefits – Consumer Attributes• Large filter media area provides optimum filtering efficiency throughout the oil change cycle
• Motorcraft oil filters feature anti-drain back valves to help prevent dry starts
• Many Motorcraft oil filter anti-drain back valves are made of silicone for greater cold/heat resistance (down
to -75 and up to +450 degrees F)
• Pressure relief valves help maintain oil supply to the engine under extreme cold conditions, or if the filter
gets clogged
• Location of relief valve in the majority of Ford application filters prevents settled debris from entering and
potentially damaging the engine
(Dome-end relief valves do not offer this protection)
• Robust steel center tubes and lock seam design withstands pressure surges and help prevent leakage
Design Features
• 80% collection efficiency on particles 20 microns or larger
• Bonded end plates help keep consistent pleat spacing
• Cellulose and polyester blend media is formulated for high capacity and strength
• The polyester content enhances the strength of the media to withstand extended exposure to hot engine
oil
Motorcraft Oil Filter Product Attributes
FL-820S
Design & Testing: Testing Conducted Specifically for Motorcraft Oil Filters• Multi-pass Efficiency and Capacity – Tests the efficiency of the filter to filter 20 micron particles and its
holding capacity
• High Temperature Resistance – tests filter integrity at 275 degrees F
• Resistance to Oil Flow – tests pressure differential throughout the filter at different flow rates
• Media Migration – ensures media is not being passed downstream of the filter
• Anti-Drain Back Leakage – tests the drain-back valve performance
• Fatigue Resistance – tests filter for leaking, cracking, fracture or rupture; 25,000 cycles of 0 PSI to
100 PSI (some up to 125 PSI)
• Internal Strength& Leakage
• Burst Pressure Test - tests filters at a minimum of 200 PSI for 60 seconds without leakage
• Relief Valve Opening – ensures relief valve opens at specified pressure
• Removal Torque
• Corrosion Resistance
• Leakage Test
Unique Offerings/Special Notes• 25 Parts numbers provide 87% coverage for all make vehicles currently in U.S. operation
Motorcraft Oil Filter Product Attributes
FL-820S
Motorcraft vs. Fram XGMotorcraft vs. Fram XG
15 flutes, black mat paint finish
Paper end caps
36 pleats, 3 ““““High
Anti-drainback valve –Nitrile Rubber (prone to
harden with heat)
Metal center tube
PH-2
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Metal tension clip with pressure relief valve
Motorcraft vs. NAPA SilverMotorcraft vs. NAPA Silver
15 Flutes
Metal end caps
54 pleats, 2 3/4”””” High
Anti-drainback and pressure relief valve –Heat resistant silicone
Metal center tube
31372
Spring for tension
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. WixMotorcraft vs. Wix
15 Flutes
Metal end caps
60 pleats, 2 5/8”””” High
Anti-drainback and pressure relief valve –
Heat Resistant Silicone
Metal center tube
Spring for tension
51372
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. MightyMotorcraft vs. Mighty
15 Flutes
Metal end caps
61 pleats, 2 3/4”””” HighBy 2 5/8” diameter
Anti-drainback and pressure relief valve – Nitrile Rubber (prone to harden with heat)
M-500
Metal center tube
Metal tension clip
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High by 3 3/8” diameter
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. ACDelcoMotorcraft vs. ACDelco
15 Flutes
White fiber end caps
58 pleats, 2”””” High
Anti-drainback and pressure relief valve – Nitrile Rubber (prone to harden with heat)
Plastic cage center tube
Metal tension clip
PF-1250
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. BaldwinMotorcraft vs. Baldwin
15 Flutes
Metal end caps
40 pleats, 2 1/2”””” High
Anti-drainback valve -Nitrile Rubber
(prone to harden with heat)
Metal center tube
B329
Spring for tension
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tubeDome-end pressure relief valve (may allow contaminants back
into engine)
Motorcraft vs. ChampMotorcraft vs. Champ
15 Flutes
Fibrous end caps
59 pleats, 2 1/8”””” High
Anti-drainback and pressure relief valve – Nitrile Rubber (prone to harden with heat)
Plastic cage center tube
Metal tension clip
PH-820
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. MicrogardMotorcraft vs. Microgard
15 Flutes
Fiber end caps
36 pleats, 2 7/8”””” High
Metal center tube
MGL2
Anti-drainback valve –Nitrile Rubber (prone to
harden with heat)
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Metal tension clip with pressure relief valve
Motorcraft vs. PennzoilMotorcraft vs. Pennzoil
15 Flutes
Dome-end pressure relief valve with plastic clip (may allow
contaminants back into engine)
Metal end caps
55 pleats, 2 3/8““““ High
Anti-drainback valve –Nitrile Rubber (prone to
harden with heat)
Metal center tube
Metal tension clip
PZ-42
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Quaker StateMotorcraft vs. Quaker State
15 Flutes
Metal end caps
44 pleats, 1 3/4”””” High
Metal center tube
QS-2
Metal tension clip
Anti-drainback valve –Nitrile Rubber (prone to harden with heat)
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. STPMotorcraft vs. STP
15 Flutes
White fiber end caps
56 pleats, 2 1/8”””” High
Anti-drainback and pressure relief valve – Nitrile Rubber (prone to harden with heat)
S-2
Metal tension clip
Plastic cage center tube
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft Competitive Comparisons
Motorcraft Competitive Comparisons
Location Design/Function
Motorcraft FL-820S Mounting plateSeparate from ADBV.
Internal mechanical springSilicone Metal Metal 50 2.38
36; Promotes
strength & easy
removal
Metal Tension Clip
AC Delco PF1250 Mounting plate PRV and ADBV are one-in-the-same Nitrile Plastic Paper 58 2.06 15 Metal Tension Clip
Amsoil EAO 11 Dome-end Internal spring Silicone Metal Metal 44 2.25 15 Metal Tension Clip
Baldwin B329 Dome-end Integral PRV Nitrile Metal Metal 40 2.44 15 Spring for tension
Bosch 3410 Dome-endIntegral PRV with plastic clip (very hard to
open)Silicone Metal Metal 65 2.44 15 Metal Tension Clip
Carquest 85372 Dome-end Integral PRV Silicone Metal Metal 56 2.88 15 Spring for tension
Champ PH820 Mounting plate PRV and ADBV are one-in-the-same Nitrile Plastic Paper 59 2.13 15 Metal Tension Clip
Donaldson P550965 Dome-end Integral PRV Nitrile Metal Metal 55 2.09 none Spring for tension
Federated LF110F Dome-end Integral PRV Nitrile (2 piece) Metal Metal 44 2.38 15 Spring for tension
Fleetguard LF3681 Dome-end Integral PRV Nitrile Metal Metal 53 2.47 15 Spring for tension
Fram Extra Guard PH2 Dome-endExternal Plastic valve w/spring mounted on
metal tension clipNitrile Metal Paper 36 3.00
15; black mat
finishMetal Tension Clip
Fram Tough Guard TG2 Dome-endExternal Plastic valve w/spring mounted on
metal tension clipSilicone Metal Paper 46 3.00
15; black mat
finishMetal Tension Clip
Hastings LF110 Dome-end Integral PRV Nitrile Metal Metal 39 2.50 15 Spring for tension
K&N HP-2010 Dome-end Integral PRV Silicone Metal Metal 51 2.19 None, but w rench
flats on top of domeSpring for tension
Luber Finer Ecore PH820 Dome-end Tension clip PRV. Nitrile Plastic Paper 54 2.125 15 Metal Tension Clip
Luber Finer PH820 Dome-end Tension clip PRV. Nitrile Metal Metal 46 2.25 15 Metal Tension Clip
MANN ML-1006 Dome-end Integral PRV w/plastic clip Nitrile Metal Metal 65 2.50 15 Metal Tension Clip
MicroGard MGL2 Dome-end External spring and plastic valve Nitrile Metal Paper 36 2.94 15Metal Tension
Clip/spring
MicroGreen MG 421-8 Dome-end Integral PRV Silicone Metal Metal 50 2.09 20 Spring for tension
Mighty M500 Mounting plate PRV and ADBV are one-in-the-same Nitrile Metal Metal 61 2.62 14 Metal Tension Clip
HEIGHT
OF FILTER
MEDIA
NUMBER
OF
FLUTES
Notes
Oil Filter Cutaways
FILTER
BRAND
PART
NUMBER
PRESSURE RELIEF VALVE (PRV) ANTI-DRAIN
BACK VALVE
(ADBV)
CENTER
TUBE
ELEMENT
FILTER
END CAP
ELEMENT
NUMBER
OF
PLEATS
Motorcraft Competitive Comparisons
Motorcraft Competitive Comparisons
Location Design/Function
Motorcraft FL-820S Mounting plateSeparate from ADBV.
Internal mechanical springSilicone Metal Metal 50 2.38
36; Promotes
strength & easy
removal
Metal Tension Clip
Mobil 1 M1-210 Dome-end Integral PRV Silicone Metal Metal 55 2.13 15 Metal Tension Clip
Motor Trend MT2 Dome-end Integral PRV Silicone Metal Metal 70 2.50 15 Metal Tension Clip
NAPA ProSelect 21372 Dome-end Integral PRV Silicone Metal Metal 52 2.75 15 Spring for tension
NAPA Gold 1372 Dome-end Integral PRV Silicone Metal Metal 56 2.84 15 Spring for tension
NAPA Silver 31372 Mounting plate PRV and ADBV are one-in-the-same Silicone Metal Metal 54 2.69 15 Spring for tension
NAPAPlatinum 41372 Dome-end Integral PRV Silicone Metal Metal 40 2.81 15 external spring
Parts Plus PH820 Dome-end Integral PRV Silicone Metal Metal 55 2.47 15 Spring for tension
Pennzoil PZ-42 Dome-end Integral PRV with plastic clip (very hard to open) Nitrile Metal Metal 55 2.38 16 Metal Tension Clip
Pro Tec 159 Mounting plate PRV and ADBV are one-in-the-same Nitrile Metal Metal 52 2.63 15 Spring for tension
ProLine PPL-24651 Dome-end Integral PRV w/plastic clip Nitrile Metal Metal 42 1.78 15 Metal Tension Clip
Pronto PO4651 Dome-end Integral PRV Silicone Metal Metal 55 2.38 15 Spring for tension
Purolator PL PL24651 Dome-end Integral PRV w/plastic clip Silicone Metal Metal 65 2.38 15 Metal Tension Clip
Purolator L L24651 Dome-end Integral PRV w/plastic clip Nitrile Metal Metal 65 2.44 15 Metal Tension Clip
Quaker State QS2 Dome-end Integral PRV w/plastic clip Nitrile Metal Metal 44 1.75 15 Metal Tension Clip
Relia Guard (FMP) R1372 Dome-end Integral PRV Nitrile Metal Metal 66 2.31 15 Spring for tension
Service Pro M4651 Dome-end Integral PRV Nitrile Metal Metal 65 2.25 15 Spring for tension
STP S2 Mounting plate PRV and ADBV are one-in-the-same Nitrile Plastic Paper 56 2.13 15 Metal Tension Clip
Sure Filter SFO4651 Dome-end Integral PRV Nitrile Metal Metal 57 2.25 15 Spring for tension
Valvoline VO-105 Dome-end Integral PRV Nitrile Metal Metal 61 2.75 14 Metal Tension Clip
Wix 51372 Mounting plate PRV and ADBV are one-in-the-same Silicone Metal Metal 60 2.63 15 Spring for tension
NUMBER
OF
FLUTES
Notes
Oil Filter Cutaways
FILTER
BRAND
PART
NUMBER
PRESSURE RELIEF VALVE (PRV) ANTI-DRAIN
BACK VALVE
(ADBV)
CENTER
TUBE
ELEMENT
FILTER
END CAP
ELEMENT
NUMBER
OF
PLEATS
HEIGHT
OF FILTER
MEDIA
Motorcraft vs. AmsoilMotorcraft vs. Amsoil
15 Flutes
Metal end caps
44 pleats, 2 1/4”””” High
Metal center tube
EAO 11
Metal tension clip
Anti-drainback valve –Heat Resistant Silicone
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. BoschMotorcraft vs. Bosch
15 Flutes
Dome-end pressure relief valve (may allow contaminants back
into engine)
Metal end caps
65 pleats, 2 7/16”””” High
Anti-drainback valve –Heat resistant Silicone
Metal center tube
Metal tension clip
#3410
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. CarQuestMotorcraft vs. CarQuest
15 Flutes
Metal end caps
56 pleats, 2 7/8”””” High
Metal center tube
85372
Anti-drainback – Heat resistant silicone
Spring for tension
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tubeDome-end pressure relief valve (may allow contaminants back
into engine)
Motorcraft vs. DonaldsonMotorcraft vs. Donaldson
15 Flutes
Metal end caps
55 pleats, 2 1/8”””” High
Anti-drainback valve –Nitrile Rubber (prone to
harden with heat)
Metal center tube
Spring for tension
P550965
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. FederatedMotorcraft vs. Federated
15 Flutes
Metal end caps
44 pleats, 2 3/8”””” High
Metal center tube
LF110F
Spring for tension
Two-piece anti-drainback valve – Nitrile Rubber (prone to harden with heat)
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube Dome-end pressure relief valve (may allow contaminants back
into engine)
Motorcraft vs. FleetguardMotorcraft vs. Fleetguard
15 Flutes
Dome-end pressure relief valve (may allow contaminants back into engine)
Metal end caps
53 pleats, 2 1/2”””” High
Anti-drainback valve – Nitrile Rubber (prone to harden
with heat)
Metal center tube
Metal Spring for tension
LF-3681
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Fram TGMotorcraft vs. Fram TG
15 flutes, black mat paint finish
Paper end caps
46 pleats, 3 ““““High
Anti-drainback valve –Heat resistant silicon
Metal center tube
Metal tension clip with pressure relief valve
TG2
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. HastingsMotorcraft vs. Hastings
15 Flutes
Metal end caps
39 pleats, 2 ½”””” High
Metal center tube
LF110
Spring for tension
Anti-drainback valve –Nitrile Rubber (prone to harden with heat)
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tubeDome-end pressure relief valve (may
allow contaminants back into engine)
Motorcraft vs. K & NMotorcraft vs. K & N
No flutes, 1”””” nut tacked to can
Dome-end pressure relief valve (may allow contaminants
back into engine)
Metal end caps
51 pleats, 2 1/8”””” High
Metal center tube
Spring for tension
HP-2010
Anti-drainback valve –Heat Resistant Silicone
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Luber Finer EcoreMotorcraft vs. Luber Finer Ecore
15 Flutes
Paper end caps
54 pleats, 2 1/8”””” High
Anti-drainback valve – Nitrile Rubber (prone to harden with heat)
Plastic center tube
Metal clip for tension
PH 820
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube Pressure relief valve
Motorcraft vs. Luber FinerMotorcraft vs. Luber Finer
15 Flutes
Metal end caps
46 pleats, 2 1/4”””” High
Anti-drainback valve – Nitrile Rubber (prone to harden with heat)
Metal center tube
Metal clip for tension
PH 820
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube Pressure relief valve
Motorcraft vs. MannMotorcraft vs. Mann
15 Flutes
Metal end caps
65 pleats, 2 1/2”””” High
Metal center tube
ML-1006
Metal tension clip
Anti-drainback valve –Nitrile Rubber (prone to harden with heat)
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. MicroGreenMotorcraft vs. MicroGreen
20 Flutes
Metal end caps
50 pleats, 2 1/8”””” High
Metal center tube
MG 421-8
Anti-drainback valve – Heat Resistant Silicone
Pressure relief valve
Spring for tension
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Mobil 1Motorcraft vs. Mobil 1
15 Flutes
Dome-end pressure internal relief valve (may allow
contaminants back into engine)
Metal end caps
55 pleats , 2 1/8”””” High
Anti-drainback valve –Heat Resistant Silicone
Metal center tube
Metal tension clip
M1-210
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Motor TrendMotorcraft vs. Motor Trend
15 Flutes
White fiber end caps
70 pleats, 2 1/2”””” High
Metal center tube
MT-2
Metal tension clip
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Anti-drainback valve –Nitrile Rubber (prone to
harden with heat)
Motorcraft vs. NAPA ProSelectMotorcraft vs. NAPA ProSelect
15 Flutes
Metal end caps
52 pleats, 2 3/4”””” High
Anti-drainback and pressure relief valve –Heat resistant silicone
Metal center tube
21372
Spring for tension
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. NAPA GoldMotorcraft vs. NAPA Gold
15 Flutes
Metal end caps
56 pleats, 2 7/8”””” High
Anti-drainback valve –Heat resistant silicone
Metal center tube
1372
Spring for tension
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. NAPA PlatinumMotorcraft vs. NAPA Platinum
15 Flutes
Metal end caps
40 pleats, 2 3/4”””” High
Pressure relief valve
Metal center tube
41372
Spring for tension
Anti-drainback valve –Heat resistant silicone
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Parts PlusMotorcraft vs. Parts Plus
15 Flutes
Metal end caps
55 pleats, 2 1/2”””” High
Metal center tube
PH820
Spring for tension
Pressure relief valve
Anti-drainback valve –Heat Resistant Silicone
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. ProLineMotorcraft vs. ProLine
15 Flutes
Dome-end pressure relief valve (may allow contaminants back
into engine)
Metal end caps
42 pleats, 1 3/4”””” High
Anti-drainback valve – Nitrile Rubber (prone to harden
with heat)
Metal center tube
Metal tension clip
PPL-24651
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. ProntoMotorcraft vs. Pronto
15 Flutes
Metal end caps
55 pleats, 2 3/8”””” High
Metal center tube
PO 4651
Spring for tension
Anti-drainback valve – Heat Resistant Silicone
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. PRO-TECMotorcraft vs. PRO-TEC
15 Flutes
Metal end caps
52 pleats, 2 5/8”””” High
Anti-drainback and pressure relief valve –
Nitrile Rubber (prone to harden with heat)
Metal center tube
Spring for tension
159
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Purolator LMotorcraft vs. Purolator L
15 Flutes
Metal end caps
65 pleats, 2 3/8”””” High
Metal center tube
L 24651
Metal tension clip
Anti-drainback valve –Nitrile Rubber (prone to harden with heat)
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Purolator PLMotorcraft vs. Purolator PL
15 Flutes
Metal end caps
65 pleats, 2 3/8”””” High
Metal center tube
PL 24651
Metal tension clip
Anti-drainback valve –Heat Resistant Silicone
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Relia Guard (FVP)
Motorcraft vs. Relia Guard (FVP)
15 Flutes
Metal end caps
66 pleats, 2 1/4”””” High
Metal center tube
R1372
Spring for tension
Anti-drainback valve –Nitrile Rubber (prone to harden with heat)
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Factory Motor Parts
Private Label Filter
Motorcraft vs. Service ProMotorcraft vs. Service Pro
15 Flutes
Metal end caps
65 pleats, 2 1/4”””” High
Metal center tube
M4651
Spring for tension
Anti-drainback valve –Nitrile Rubber (prone to harden with heat)
Pressure relief valve
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube
Motorcraft vs. Sure FilterMotorcraft vs. Sure Filter
15 Flutes
Metal end caps
57 pleats, 2 ¼”””” High
Anti-drainback valve – Nitrile Rubber (prone to harden with heat)
Metal center tube
Spring for tension
SFO 4651
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tubePressure relief valve
Motorcraft vs. ValvolineMotorcraft vs. Valvoline
15 Flutes
Metal end caps
61 pleats, 2 3/4”””” High
Pressure relief valve
Metal tension clip
Metal center tube
VO-105
Anti-drainback valve –Nitrile Rubber (prone to
harden with heat)
Metal tension clip
Metal end caps
50 pleats, 2 5/8 ”””” High
Anti-drainback valve –Heat Resistant Silicone
Internal pressure relief valve at inlet
FL-820S
50 flutes. More flutes for easy removal
Metal center tube