TamliteLightingPORT SAINT LUCIE, FL USA

TamliteLightingPORT SAINT LUCIE, FL USA

Corrosion Resistant Polycarbonate Construction

Pre-Wired/Pre-Assembled

Tool Free Adjustment

180° and 270° PIR Sensors AvailableMS se

ries

M O T I O N S E N S O RL I G H T I N G

Visit us @ www.tamliteusa.com

WARRANTY INFORMATIONGuaranteed one year from the purchase date of the product, against mechanical defects in manufacturing.*** SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE***

TAMLITE TAMCO 660 NW Peacock Blvd., Port Saint Lucie, FL 34986 phone: 772.878.4944 fax: 772.879.2434 www.tamliteusa.com

HOW THE SENSOR WORKSA person entering the monitored area is detected when the infrared energy emitted from the intruder’s body is focused by the Fresnel lens and then overlaps a section of the sensor; which had previously been looking at a much cooler part of the protected area. That portion of the sensor is now much warmer than when the intruder wasn’t there. As the intruder moves, so does the hot spot on the surface of the sensor. This moving hot spot causes the electronics connected to the sensor to de-energize the relay, operating its contacts, thereby activating the fixture and turning on the lights.

The greater the temperature differential between the ambient temperature and the object entering the field of view is essential for optimum performance of the PIR sensor. A PIR fixture that is operating in a higher ambient temperature will be less likely to detect objects entering its field of view because the temperature differential is less than if it was operating in a cooler environment.

M O T I O N S E N S O R L I G H T I N G

PASSIVE INFARED TECHNOLOGYA Passive Infrared sensor (PIR sensor) is an electronic device which measures infrared light radiating from objects in its field of view. Apparent motion is detected when an infrared source with one temperature, such as a human, passes in front of an infrared source with another temperature, such as a wall.

The term “passive” in this instance means the PIR does not emit energy of any type but merely accepts incoming infrared radiation.

SENSOR & ELECTRONICSTo make a sensor that can detect a human being, you need to make the sensor sensitive to the temperature of a human body. Humans, having a skin temperature of about 93 degrees Farenheit, radiate infrared energy with a wavelength between 9 and 10 micrometers. Therefore, the sensors used in the MS series have a sensitivity range of 8 to 12 micrometers.

LENS FUNCTIONALITYThe specially designed lenses used in our MS series are equally as important as the sensor. We offer two wide field view lens options of either 180 degrees or 270 degrees. These wide field views are possible because infrared energy is a form of light, meaning it can be focused and bent with the use of our specially designed Fresnel pattern that is molded inside our lenses. The lenses also help prevent the intrusion of dust and insects which could potentially obscure or block the field of view of the sensor.

>

ONICSSSENSOR & E& ELECTRCTRO

Sensors

INSTALLATION TIPS:

keep in mind that the detection fields created from the Fresnel lens are most effective when an intruder walks through the fields not directly towards one.

position for your motion sensor not to place it by any air supply, returns or exhaust vents as the change in temperature around the fixture could cause false alarms.

mounting height of 8’.

DEFINING PASSIVE INFARED TECHNOLOGY

TamliteLightingPORT SAINT LUCIE, FL USA

sensormotion

Detention Range Top View

Detention Range Side ViewTEST: For testing or using this motion sensor lighting fixture during daytime put the TIME switch to the TEST position, and put the SENSOR switch to 24 HR position.

24HR 24 hours are MS function

NIGHT Dusk to dawn is MS, no function in daytime

TIME Function

1 Light remains on for 1 minute after activation

5 Light remains on for 5 minutes after activation

10 Light remains on for 10 minutes after activation

TEST Manual Override

SENSOR FUNCTION

TEST: For testing or using this motion sensor lighting fixture during daytime set the TIME switch to the TEST position, and put the SENSOR switch to 24 HR position, and set the SECURITY to the NORMAL position.

NORMAL 24 hours 24 Hours are MS function

NORMAL NIGHT Dusk to dawn is MS, no function in daytime

3 or 6 24 HR MS function in daytime, after dusk light on 3 or 6 hours, then turns 6 hours, then turns to MS function 3 or 6 only functioned after dark.

3 or 6 NIGHT Light on in dusk automatically 3 or 6 Hours, then turn to MS function to dawn. No function in daytime.

DUSK/DAWN 24 HR MS function in daytime. Auto light on in dusk, turn off in dawn

DUSK/DAWN NIGHT Light on from dusk to dawn auto, no function in daytime

SECURITY SENSOR FUNCTION

Detention Range Top View

Detention Range Side ViewSCAN FOR ALL MS SERIES

SPEC SHEETS

180° MOTION LIGHT 2 X 150W PAR38 WHITE 270° MOTION LIGHT 2 X 150W PAR38 BRONZE

270° MOTION LIGHT 2 X 150W PAR38 WHITE

270° MOTION LIGHT 2 X 150WPAR38 WITH WHITE HOODS

270° MOTION LIGHT 2 X 150W PAR38 WITHBRONZE HOODS

150W PAR38 LAMP HOLDER 2 BRONZE HEAD

150W PAR38 LAMP HOLDER 2 WHITE HEAD

MSP2180WH

MSP2180BZ

MSP2180HBZ

MSP2180HWH

MSP2BZ

MSP2WH

MSP2270BZ

MSP2270WH

MSP2270HWH

MSP2270HBZ

180° MOTION LIGHT 2 X 150W PAR38 WITH BRONZE HOODS

180° MOTION LIGHT 2 X 150W PAR38 WITH WHITE HOODS

PAR38 LAMP HOLDER WHITE HOOD(SOLD INDIVIDUALLY)

MSHWH

MSHBZPAR38 LAMP HOLDER BRONZE HOOD (SOLD INDIVIDUALLY)

** LAMPS NOT INCLUDED **

180° MOTION LIGHT 2 X 150W PAR38 BRONZE