Monthly Notifications RegisterMonthly Notifications Register Notifications registered at CCMC from...

Information procedure

Monthly Notifications Register

Notifications registered at CCMC from 2010-10-01 to 2010-10-31

Register issued on : 2010-11-05

A list of subsectors can be found at the end of this document.




Sector A : SERVICES


Subsector A01: TOURIST SERVICES

Subsector : A01 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-16Project ID : P0024788/0002 Draft for public enquiryICS :National Ref : PNE 167012Title : Hospitality services. Catering services. Requirements for the implementation of a self

control system based on HACCP principles.Scope : This project describes a HACCP system for restaurants.

Relatedness :National : REV/AMD UNE 167004:2006

Subsector : A01 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036557/0001 Project EstablishedICS :National Ref : PNE 187002Title : Natural protected areas. Service provision requirements.Scope : This standard specifies the service provision requirements in natural protected areas.

Relatedness :National : New

** End of Subsector **

Subsector A99: UNDETERMINED

Subsector : A99 Registration Date : 2010-10-21Organization : SIS Draft Issue Date : 2010-10-19Country : Sweden Latest Date for Comments : 2010-12-19Project ID : 00010700/0001 Draft for public enquiryICS :National Ref : 10700Title : Education - Learning opportunities information - Metadata and exchange formatsScope : Quality assurance and management of use of data to and from educational instances in

Sweden

Relatedness :National : NewEuropean : Modified prEN 15982

Subsector : A99 Registration Date : 2010-10-05Organization : BSICountry : United KingdomProject ID : 01002874/0001 Project EstablishedICS :National Ref : BS 11000-2Title : Collaborative business relationships. Part 2. Guide


Subsector : A99 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001601/0001 Project EstablishedICS : 03.060, 03.080.99National Ref : NEN 8048-1:2010 Concept nlTitle : Debt settlement - Part 1: Requirements for organisations in debt settlementScope : This standard contains requirements for testing and assessing organisations and persons

working with debt settlement. This standard applies to the primary proces of debt settlement.


Subsector : A99 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001602/0001 Project EstablishedICS : 03.060, 03.080.99National Ref : NEN 8048-3:2010 Concept nlTitle : Debt settlement - Part 3: Certification scheme for organisations in debt settlementScope : The standard and certification based on this standard must lead to transparency and

profesionalization of debt settlement and its employees.


Subsector : A99 Registration Date : 2010-10-18Organization : SNCountry : NorwayProject ID : NOT10012/0001 Project EstablishedICS : 13.020.99National Ref : prNS 9452Title : Influencing factors on Norwegian natureScope : Standardization of a list of defined concepts relating to influence on Norwegian nature



** End of Sector **




Sector B : BUILDING AND CONSTRUCTION


Subsector B01: FIRE PROTECTION

Subsector : B01 Registration Date : 2010-10-01Organization : AENORCountry : SpainProject ID : P0036433/0001 Project EstablishedICS :National Ref : PNE 23745Title : Fire safety. Fire resistant metallic duct systems for ventilation and extraction. Installation

and maintenance guideScope : This standard provides necessary information for proper installation and maintenance of

fire resistance metallic duct systems.


Subsector : B01 Registration Date : 2010-10-01Organization : AENORCountry : SpainProject ID : P0036436/0001 Project EstablishedICS :National Ref : PNE 23746Title : Fire safety. Fire dampers. Installation and maintenance.Scope : This standard provides necessary information for proper installation and maintenance of

fire dampers



Subsector B02: STRUCTURES

Subsector : B02 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 73032470/0001 Project EstablishedICS : 53.080National Ref : U73032470Title : Metallic storage systems - Design of drive-in and drive-through racking systems for

static pallet storageScope : This technical standard defines the design procedures for Drive-in and Drive-trough

racks.Drive-in and Drive-trough racks are pallet storage systems differing from adjustable pallet racking in terms of structural elements, structural behaviour and method of operation.This standard is based on the safety design concept of the European racking standards and provides supplementary design rules where peculiarities of the Drive-in and Drive-trough racks do not allow the full application of the above mentioned standards.


Subsector : B02 Registration Date : 2010-10-11Organization : NBN Draft Issue Date : 2010-10-20Country : Belgium Latest Date for Comments : 2011-03-20

Project ID : BE052819/0001Draft for public

enquiryICS : 93.080.40National Ref : prNBN L 18-004Title : Road lighting - Selection of lighting classes


Subsector : B02 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036618/0001 Project EstablishedICS :National Ref : PNE 123003Title : Calculation, design and installation of free-standing chimneysScope : Calculation and execution specifications that are not regulated by the relevant European

standards.



Subsector B09: THERMAL MATTERS

Subsector : B09 Registration Date : 2010-10-25Organization : SNV Draft Issue Date : 2010-10-20Country : Switzerland Latest Date for Comments : 2011-01-14Project ID : CH100019/0001 Draft for public enquiryICS :National Ref : SIA 180Title : Thermal and moisture protection in construction

Relatedness :National : REV/AMD SIA 180 (1999)

Subsector : B09 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036448/0001 Project EstablishedICS :National Ref : PNE 92325 INTitle : Thermal insulation products for buildings. Installation control.Scope : It is well known that thermal insulation products have a significant impact on the

consumption of energy in buildings. To achieve nearly zero-energy buildings it is necessary to provide the buildings with an optimal thermal insulation in the roofs, floors and façades. Therefore, the control of insulation during the building process is essential. This Technical specification provides information to control thermal insulation products during the project, construction works for new buildings and refurbishment. Checklists are included to verify thermal insulation products installed in buildings.

Relatedness :

National : New


Subsector B12: MASONRY

Subsector : B12 Registration Date : 2010-10-08Organization : LSTCountry : LithuaniaProject ID : 10000652/0001 Project EstablishedICS : 91.100.99National Ref :Title : Viscous building putties - Technical specificationsScope : This Standard applies to viscous building putties used for interior and exterior finishes of

buildings.



Subsector B13: SOLAR ENERGY

Subsector : B13 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 0209C280/0001 Project EstablishedICS : 27.160National Ref : E0209C280Title : Large solar-assisted heating systems for domestic hot water production and/or air

conditioning - Classification, essential requirements, guidelines for construction, trade offer, final order, acceptance tests

Scope : The standard provides instructions for building (including safety requirements), request for offer and offer document preparing, ordering and testing of large solar-assisted heating systems classified by european standards as Large Custom Built



Subsector B17: LIGHTING EQUIPMENT AND LIGHTING APPLICATION TECHNOLOGY

Subsector : B17 Registration Date : 2010-10-11Organization : ASICountry : AustriaProject ID : 00023534/0001 Project EstablishedICS : 97.200.10National Ref : ONR 151060Title : Event equipment - Guidelines for the installation and operation of mobile lighting and

sound installationsScope : This ONR defines the guidelines for the installation and operation of mobile event

equipment. This also includes support during and dismantling after the end of the event. Furthermore the definition of work equipment and work processes is described. The ONR is intended to serve as a guide for authorities, organizers, operators of event facilities, lighting and sound engineers as well as for event specialists.


Subsector : B17 Registration Date : 2010-10-11Organization : NBN Draft Issue Date : 2010-10-20Country : Belgium Latest Date for Comments : 2011-03-20Project ID : BE052818/0001 Draft for public enquiryICS : 91.010.30, 93.040National Ref : prNBN EN 1991-2 ANBTitle : Eurocode 1 : Actions on structures - Part 2 : Traffic loads on bridges - National annex



Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT

Subsector : B25 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 01029181/0001 Project EstablishedICS : 75.060National Ref : E01029181Title : Initial pressure reduction plants for natural gas - Part 1: SurveillanceScope : The Standard defines the prescription for the surveillance of the gas supply pants (REMI)

downstream trasport lines to maintain the safety, the efficiency and to secure the gas delivery without interruptions.

Relatedness :National : REV/AMD UNI 9571:1990


Subsector B26: ROAD BUILDING AND MAINTENANCE

Subsector : B26 Registration Date : 2010-10-13Organization : SUTNCountry : SlovakiaProject ID : 73009210/0001 Project EstablishedICS :National Ref : STN 28 0315/Z4Title : Structural clearances of state and industrial tracks for railway gauge 1435 mm and 1520

(1524) mm. Basic provisionsScope : Modification of the part D. Tunnel clearance due to new tunnel clearances defined in new

standard STN 73 7508 Design of railway tunnels

Relatedness :National : REV/AMD STN 28 0315

Subsector : B26 Registration Date : 2010-10-07Organization : SNV Draft Issue Date : 2010-10-05Country : Switzerland Latest Date for Comments : 2010-11-09

Project ID : CH100018/0001 Draft for public enquiryICS : 93.080.01National Ref : SN 640034bTitle : Presentation of projects; signatures for geotechnical engineering and geology

Relatedness :National : REV/AMD SN 640034a (1997)


Subsector B27: WATERPROOFING MATERIALS

Subsector : B27 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-16Project ID : P0036119/0002 Draft for public enquiryICS :National Ref : PNE 88113Title : Fibre-cement profiled sheets incorporating PUR and polyester coating at the bottom,

and fittings - Requirements and test methodsScope : This document specifies the technical requirements and establishes the test methods for

fibre-cement profiled sheets incorporating PUR and polyester coating at the bottom, and its fittings. This document covers fibre-cement profiled sheets that incorporate in a second production process a PUR layer between the fibre-cement and a polyester coating placed at the bottom. This is done by means of an individual injection system. The final product is a slab with better mechanical characteristics and more anti-corrosive resistance. For the purpose of this document fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics. This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.



Subsector B99: UNDETERMINED

Subsector : B99 Registration Date : 2010-10-05Organization : BSICountry : United KingdomProject ID : 01002852/0001 Project EstablishedICS :National Ref : BS 8560Title : Code of practice on design for working at height


Subsector : B99 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001597/0001 Project EstablishedICS : 91.010.30

National Ref : NEN 2767-4-1:2010 Concept nlTitle : Condition assessment of building and installation components - Part 4-1: Infrastructure,

additional methodsScope : This standard describes inspection methods for condition assessment of buildings. For the

inspection of infrastructure the same methods are used with some modifications. The modifications are listed in this standard.


Subsector : B99 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001598/0001 Project EstablishedICS : 91.010.30National Ref : NEN 2767-4-2:2010 Concept nlTitle : Condition assessment of building and installation components - Part 4-2: Infrastructure,

decomposition and list of defectsScope : This standard sets out a complete decomposition of infrastructure. All these buidling

elements can contain defaults, listed in this standard. Because of the enormous size and structure of this standard, this part is published as a database.


Subsector : B99 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001599/0001 Project EstablishedICS : 91.020National Ref : NEN 2776:2010 Concept nlTitle : Real estate - Terminology and definitionsScope : This standard contains relevant terminology for management and maintenance of real

estate. The terms are defined in such a way that they are applicable on a operational, strategic and tactic level.



** End of Sector **




Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS


Subsector C01: Food products

Subsector : C01 Registration Date : 2010-10-18Organization : MSZT Draft Issue Date : 2010-10-14Country : HungaryProject ID : 34860402/0001 Project EstablishedICS : 67.060National Ref :Title : Wheat

Relatedness :National : REV/AMD MSZ 6383

Subsector : C01 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 59007960/0001 Project EstablishedICS : 67.020National Ref : U59007960Title : Agricultural and food products - Minimum requirements for non GMO declarationScope : This standard specifies minimum requirements for agricultural and food products to be

declared non GMO.


Subsector : C01 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 590C7990/0001 Project EstablishedICS : 67.260National Ref : U590C7990Title : Appliances for the production and dispense of hot beverages for public catering - Test

methods and migration limits of lead and nickelScope : This standard specifies migration limits of lead and nichel in appliances for the production

and dispense of hot beverages for public catering.


Subsector : C01 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 59108020/0001 Project EstablishedICS : 67.120.10National Ref : U59108020Title : Meat and meat products - Determination of moisture content - Rapid methodScope : This standard specifies a rapid method for the determination of moisture content in meat

and meat products.


Subsector : C01 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 59108030/0001 Project EstablishedICS : 67.120.10National Ref : U59108030Title : Meat and meat products - Determination of nitrogen content (Reference method)Scope : This standard specifies a reference method for the determination of nitrogen content in

meat and meat products.


Subsector : C01 Registration Date : 2010-10-01Organization : AENORCountry : SpainProject ID : P0035813/0001 Project EstablishedICS :National Ref : PNE 155204Title : Fruits for fresh consumption. Controlled production. Avocado.Scope : This project establishes the requirements of a production system for avocado tree the main

destination of which is the fresh consumption, under controlled conditions.

Relatedness :National : REV/AMD UNE 155004-2:2004


Subsector C02: PAINTS AND RELATED PRODUCTS

Subsector : C02 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170392/0001 Project EstablishedICS :National Ref : PR NF T30-901Title : Paints and varnishes - Paint for nuclear industry - Performance test for susceptibility to

contamination and fitness to decontamination



Subsector C03: CHEMISTRY

Subsector : C03 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-06Project ID : P0034703/0002 Draft for public enquiryICS :National Ref : PNE 84120Title : Cosmetic raw materials. Sorbic acid.Scope : The scope of this standard is to define the physic-chemical characteristics of sorbic acid for

its use as ingredient in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036555/0001 Project EstablishedICS :National Ref : PNE 84091Title : Cosmetic raw materials. Phenoxyethanol.Scope : Specifications required by phenoxyethanol and used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036584/0001 Project EstablishedICS :National Ref : PNE 84098Title : Cosmetic raw materials. Imidazolidinyl urea.Scope : Specifications required by imidazolidinyl urea used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036612/0001 Project EstablishedICS :National Ref : PNE 84617Title : Cosmetic raw materials. PEG-3 Distearate.Scope : Specifications required by ethylenglycol to be used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036613/0001 Project EstablishedICS :National Ref : PNE 84618Title : Cosmetic raw materials. PEG-8 Distearate.Scope : Specifications required by ethylenglycol to be used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036614/0001 Project EstablishedICS :National Ref : PNE 84633Title : Cosmetic raw materials. Sorbitan caurate.Scope : Specifications required by sorbitan oleate used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036615/0001 Project EstablishedICS :National Ref : PNE 84634Title : Cosmetic raw materials. Sorbitan laurate.Scope : Specifications required by sorbitan laurate used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036616/0001 Project EstablishedICS :National Ref : PNE 84635Title : Cosmetic raw materials. Sorbitan palmitate.Scope : Specifications required by sorbitan palmitate used in cosmetic products.


Subsector : C03 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036617/0001 Project EstablishedICS :National Ref : PNE 84637Title : Cosmetic raw materials. Sorbitan stearate.Scope : Specifications required by sorbitan stearate used in cosmetic products.



Subsector C06: ESSENTIAL OILS

Subsector : C06 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170763/0001 Project EstablishedICS :National Ref : PR NF T75-234Title : Essential oil of palmarosa (Cymbogon martinii (Roxburgh) W. Watson var. motia



Subsector C99: UNDETERMINED

Subsector : C99 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 01200331/0001 Project EstablishedICS :National Ref : 01200331Title : Beverage dispensing systems - Accessories - Part 4: Remote coolers


Subsector : C99 Registration Date : 2010-10-25Organization : TSECountry : TurkeyProject ID : tst00382/0001 Project EstablishedICS : 67.080.20National Ref :Title : Canned Peas


Subsector : C99 Registration Date : 2010-10-25Organization : TSECountry : TurkeyProject ID : tst00887/0001 Project EstablishedICS : 67.200.10National Ref :Title : Edible cottonseed oil


Subsector : C99 Registration Date : 2010-10-25Organization : TSECountry : TurkeyProject ID : tst01070/0001 Project Established

ICS : 67.120.10National Ref :Title : Sucuk (Turkish style fermented sausage)



** End of Sector **




Sector F : FUNDAMENTAL STANDARDS


Subsector F12: INFORMATION PROCESSING SYSTEMS

Subsector : F12 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001600/0001 Project EstablishedICS : 35.240.40National Ref : NPR 5315:2010 Concept nlTitle : Open networks - Interconnecting of digital networks - Recommendations for VLAN

requirements base on Ethernet Virtual Connections (EVCs)Scope : This code of practice contains technical specifications for an open digital infrastructure of

glassfibre networks connected by EVCs.


Subsector : F12 Registration Date : 2010-10-07Organization : NENCountry : Netherlands

Project ID : 50001603/0001Project

Established

ICS :01.140.20, 35.060, 35.240.30, 35.240.99

National Ref : NEN 2082:2010 Concept nlTitle : Taxonomy of document typesScope : This document gives a taxonomy of document types. Included are document types used for

the whole society. This is a basis taxonomy.



Subsector F20: QUALITY ASSURANCE

Subsector : F20 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170404/0001 Project EstablishedICS :National Ref : PR NF X50-135Title : SUSTAINABLE PURCHASING



** End of Sector **




Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE


Subsector H09: FURNITURE

Subsector : H09 Registration Date : 2010-10-14Organization : NSAICountry : IrelandProject ID : 01078874/0001 Project EstablishedICS : 97.140National Ref : I.S. 419/A2Title : Fire safety requirements for components of furnitureScope : Amendment to Standard will specify fire safety requirements for components to furniture.

Relatedness :National : REV/AMD I.S. 419/Amd.


Subsector H99: UNDETERMINED

Subsector : H99 Registration Date : 2010-10-29Organization : UNMZ Draft Issue Date : 2010-11-30Country : Czech Republic Latest Date for Comments : 2011-02-28Project ID : 91001010/0001 Published StandardICS :National Ref :Title : Upholstered furniture - Technical requirementsScope : The standard defines the common characteristics and requirements for upholstered

furniture

Relatedness :National : REV/AMD CSN 91 0015:1990

Subsector : H99 Registration Date : 2010-10-29Organization : UNMZ Draft Issue Date : 2010-10-31Country : Czech Republic Latest Date for Comments : 2011-01-31Project ID : 91001110/0001 Published StandardICS :National Ref :Title : Furniture Storage - Technical requirementsScope : The standard defines common standards and characteristics of the storage furniture

The standard defines common standards and characteristics of the storage furniture

Relatedness :National : REV/AMD


** End of Sector **




Sector I : MECHANICAL ENGINEERING


Subsector I19: NUCLEAR ENERGY

Subsector : I19 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 08000171/0001 Project EstablishedICS :National Ref : 08000171Title : Medical electron accelerators - Part 6: Electronic image receptors - Constancy testing


Subsector : I19 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 54032170/0001 Project EstablishedICS : 13.030.30National Ref : U54032170Title : Radioactive waste packages - CharacterizationScope : This standard defines the tests for the characterization radioactive waste packages for their

confinment and disposal.


Subsector : I19 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 54032180/0001 Project EstablishedICS : 13.030.30National Ref : U54032180Title : Radioactive waste - ClasificationScope : This standard defines the classification of radioactive waste (both solid and liquid), anyhow

made, ranking the in groups, types and classes.


Subsector : I19 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 54032190/0001 Project EstablishedICS : 13.030.30National Ref : U54032190Title : Radioactive waste packages - Colouring, marking, recording and filingScope : This standard defines the methods for colouring, marking, recording and filing of

radoactive waste packages.



Subsector I21: CHAINS AND CHAIN WHEELS

Subsector : I21 Registration Date : 2010-10-18Organization : SNCountry : NorwayProject ID : NOT10013/0001 Project EstablishedICS : 43.080.01, 83.160.10National Ref : prNS 5960Title : Snow chains for vehicles classes N2, N3, M2, M3, O3, O4 - Requirements, testing and

markingScope : This standard prescribe requirements and test methodes for snow chains to be mounted on

trucks, busses and their trailers. The standard states minimum requirements to characeristics, driving safety, lifetime, instruction manuals and marking.



** End of Sector **




Sector M : METALLIC MATERIALS


Subsector M01: STEEL

Subsector : M01 Registration Date : 2010-10-29Organization : UNMZCountry : Czech RepublicProject ID : 42006010/0001 Project EstablishedICS : 77.140.15, 77.140.60National Ref :Title : Steel for the reinforcement of cocrete - Weldable ribbed reinforcing steel - General

Relatedness :National : REV/AMD ČSN 42 0139 (2007)European : Not Equivalent to EN 1992-1-1 (2004)


Subsector M05: WELDING

Subsector : M05 Registration Date : 2010-10-11Organization : ASICountry : AustriaProject ID : 00023535/0001 Project EstablishedICS : 01.040.25, 25.160.50National Ref : ÖNORM ISO 857-2Title : Welding and allied processes - Vocabulary - Part 2: Soldering and brazing processes

and related terms (ISO 857-2:2005)Scope : This part of ISO 857 defines terms used for metal soldering and brazing processes, as well as

related terms.



Subsector M08: LIGHT ALLOYS

Subsector : M08 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 93043990/0001 Project EstablishedICS : 87.040National Ref : U93043990Title : Paints and varnishes - Organic coatings on aluminium and its alloys - Requirements and

test methods on coated aluminium with liquid coatings for architectural purposesScope : This standard specifies the requirements and the corresponding methods of test relatig to

the organic coating of aluminium and aluminium alloy extrusions, sheet and preformed sections for architectural purposes (external use), using liquid coatings. It also describes: a) the pre-treatment of the substrate prior to the coating process; b) the liquid coating; c) the coating process; d) the final product.



Subsector M10: METALLIC COATINGS

Subsector : M10 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 68002290/0001 Project EstablishedICS : 25.220.40National Ref : U68002290Title : Metallic protective coatings of ferrous materials - Zinc layer uniformity test on hot

galvanized materials - Preece testScope : The standard defines a quantitative test method suitable for the uniformity of zinc layers

applied to steel items by hot dipping. The standard bases on the UNI 5743:1966 withdrawn.



Subsector M20: TIN AND TIN ALLOYS

Subsector : M20 Registration Date : 2010-10-25Organization : UNICountry : ItalyProject ID : 93030727/0001 Project EstablishedICS : 77.150.60National Ref : U93030727Title : Tin scraps - Types, characteristics and chemical composition - Part 7: Soldering tin lead

free alloysScope : This Italian Standard specifies, types, characteristics, extra loss and designation from tin



** End of Sector **




Sector N : NON-METALLIC MATERIALS


Subsector N01: PAPER AND BOARD

Subsector : N01 Registration Date : 2010-10-01Organization : AENORCountry : SpainProject ID : P0036435/0001 Project EstablishedICS :National Ref : PNE 23036Title : Fire Safety. Safety signs. Guide for installation and maintenance.Scope : This standard provides the rules to be followed for carrying out installation and

maintenance of the photoluminescent signs. This standard applies to the signaling system comprising photoluminescent signs, markings and drawings used in evacuation exits, emergency exits, evacuation routes, accessible routes, shelter areas, fire protection equipment, as well as specific risk areas.



Subsector N03: PETROLEUM PRODUCTS

Subsector : N03 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 06233520/0001 Project EstablishedICS :National Ref : 06233520Title : Fuels for small engines- Requirements and test methods



Subsector N04: REFRACTORIES

Subsector : N04 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 1319D060/0001 Project EstablishedICS : 83.140.10National Ref : E1319D060Title : Biodegradable thermoplastic materials for use in agriculture and horticulture - Mulching

films - Requirements and test methodsScope : This standard applies to the films made with biodegradable thermoplastic polymers

processed to films added with concentrated color (blacks or white / blacks) for use as mulching films in agriculture and horticulture.


Subsector : N04 Registration Date : 2010-10-01Organization : UNI

Country : ItalyProject ID : 1321C930/0001 Project EstablishedICS : 55.080National Ref : E1321C930Title : Compostable and biodegradable shopping bags for the transport of retail goods - Types,

requirements and test methodsScope : This standard defines the shape, size and requirements to be met by the shopping bags of

thermoplastic biodegradable and compostable films according to UNI EN 13432 "Packaging - Requirements for packaging recoverable through composting and biodegradation - Test scheme and criteria assessment for the final acceptance of packaging ". These products also known under the name "Shoppers", made from tubular film with side gusset by means of thermal welding, cutting and die-cut, are for the transport of packaged and not packaged products for retail distribution.


Subsector : N04 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 1321D050/0001 Project EstablishedICS : 85.080National Ref : E1321D050Title : Compostable and biodegradable sacks for urban solid waste collection - Types,

requirements and test methodsScope : This standard defines the dimensions and the requirements to be met by the sacks of

biodegradable and compostable thermoplastic material, for the collection of the organic fraction of municipal solid waste (F.O.R.S.U). This standard applies to sacks, any configured, made from tubular film that is cut and welded closed by welding. The welding operation can be performed on tubular plain film (simple sacks ) or on tubular films with side gusset (sacks with gusset).



Subsector N06: RUBBER

Subsector : N06 Registration Date : 2010-10-11Organization : ASICountry : AustriaProject ID : 00023536/0001 Project EstablishedICS : 83.060National Ref : ÖNORM ISO 815-1Title : Rubber, vulcanized or thermoplastic - Determination of compression set - Part 2: At

ambient or elevated temperatures (ISO 815-1:2008)Scope : This part of ISO 815 specifies methods for the determination of the compression set

characteristics of vulcanized and thermoplastic rubbers at ambient or elevated temperatures. The methods are intended to measure the ability of rubbers of hardness within the range 10 IRHD to 95 IRHD to retain their elastic properties at specified temperatures after prolonged compression at constant strain (normally) under one of the alternative sets of conditions described. For rubber of nominal hardness 80 IRHD and above, a lower compression strain is used: for a nominal hardness from 80 IRHD to 89 IRHD and for a nominal hardness from 90 IRHD to 95 IRHD.


Subsector : N06 Registration Date : 2010-10-11Organization : ASICountry : AustriaProject ID : 00023554/0001 Project EstablishedICS : 83.060National Ref : ÖNORM ISO 815-2Title : Rubber, vulcanized or thermoplastic - Determination of compression set - Part 2: At low

temperatures (ISO 815-2:2008)Scope : This part of ISO 815 specifies a method for the determination of the compression set

characteristics of vulcanized and thermoplastic rubbers at low temperatures. The method is intended to measure the ability of rubbers of hardness within the range 10 IRHD to 95 IRHD to retain their elastic properties at specified temperatures after prolonged compression at constant strain (normally) under one of the alternative sets of conditions described. For rubber of nominal hardness 80 IRHD and above, a lower compression strain is used: for a nominal hardness from 80 IRHD to 89 IRHD and for a nominal hardness from 90 IRHD to 95 IRHD.


Subsector : N06 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170526/0001 Project EstablishedICS :National Ref : PR XP T47-761-1Title : End of Life Tyres (ELT) - Determination of residual impurities content for steel from

grinding process of End of Life Tyres - Method based on pyrolisis



Subsector N09: PLASTICS

Subsector : N09 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-06Project ID : P0035654/0002 Draft for public enquiryICS :National Ref : PNE 53963 INTitle : Plastics. Cellular flexible polymeric materials. Tolerances on the nominal value of

polyurethane (PUR) conglomerate foams characteristics.Scope : It pretends to show to the users (furniture, manufacturers, packaging industry,

construction, etc.) and final consumers, the deviations that may occur on the values of main physical properties of pieces cutted from the same block.

Relatedness :National : REV/AMD UNE 53963:2000 IN


Subsector N99: UNDETERMINED

Subsector : N99 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036556/0001 Project EstablishedICS :National Ref : PNE 304201Title : Jet. Characteristics of jet "Asturias type"Scope : This standard aims to characterize the jet and specifically the "Asturias type" jet. Apart from

the physical and chemical properties, the characterization is done by its identification under microscope.



** End of Sector **




Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT


Subsector S01: ACOUSTICS AND SOUND INSULATION

Subsector : S01 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 20002030/0001 Project EstablishedICS : 91.060.50National Ref : U20002030Title : Acoustics - Extensibility of sound reduction index for buildingScope : The Technical Report is an guideline to application of EN 14351-1and for the extensibility of

sound reduction index laboratory values for building. The document indicates the maior extensibility criteria of values by measurements under laboratory conditions in conformity with the reference standards The Technical Report is applicable to windows and doors height windows with and without …( shutter) and external pedestrian doorsets with and without …(…)



Subsector S04: PROTECTIVE CLOTHING AND EQUIPMENT

Subsector : S04 Registration Date : 2010-10-21Organization : SIS Draft Issue Date : 2010-10-19Country : Sweden Latest Date for Comments : 2010-12-10Project ID : 08760039/0001 Project EstablishedICS :National Ref : 8760039Title : Health care textiles - Rescue sheet and mattress cover with evacuation functionScope : This standard is a revision


Subsector : S04 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 5002A790/0001 Project EstablishedICS : 13.340.50National Ref : U5002A790Title : Safety footwear, protective footwear and occupational footwear - Criteria for selection,

use, care and maintenanceScope : The Technical Report provides guidance for selection, use, care and maintenance of safety,

protective and occupational footwear for professional use. It is designed for footwear manufacturers, suppliers, employers and self-employed people, safety engineers and users.



Subsector S06: VIBRATION & SHOCK

Subsector : S06 Registration Date : 2010-10-14

Organization : DINCountry : GermanyProject ID : 00100843/0001 Project EstablishedICS :National Ref : 00100843Title : Vibration measuring instrumentation - Vocabulary



Subsector S08: AIR QUALITY

Subsector : S08 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170408/0001 Project EstablishedICS :National Ref : PR XP X43-298Title : Workplace air. Guidance for external participation in view of assessing by air sampling

professional exposure to chemical risk at workplaces.



Subsector S13: ERGONOMICS

Subsector : S13 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170619/0001 Project EstablishedICS :National Ref : PR NF X35-701Title : Ergonomic principles for the conception of cash counters - Retail trade with food

ascendancy in self-service



Subsector S17: RESPIRATORY PROTECTIVE DEVICES

Subsector : S17 Registration Date : 2010-10-01Organization : UNICountry : ItalyProject ID : 5002A800/0001 Project EstablishedICS : 13.340.30National Ref : U5002A800Title : Self-contained open-circuit compressed air breathing apparatus - Guidelines for

maintenanceScope : The standard is addressed to users of self-contained open-circuit compressed air breathing

apparatus and it provides guidelines on the functioning and maintenance of such

Scope : apparatus. The scope of the standard is to give the criteria which may enable the user to be aware of elements to be taken care of which, if neglected, may lead to failures of the apparatus.



Subsector S19: FIRST AID EQUIPMENT AND RESCUE SYSTEMS

Subsector : S19 Registration Date : 2010-10-05Organization : BSICountry : United KingdomProject ID : 01002677/0001 Project EstablishedICS :National Ref : BS 8599-1Title : Workplace first aid kits. Part 1. Specification for the contents of workplace first aid kits


Subsector : S19 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 06301432/0001 Project EstablishedICS :National Ref : 06301432Title : First aid material - First aid box B


Subsector : S19 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 06301433/0001 Project EstablishedICS :National Ref : 06301433Title : First aid material to be carried on motorcycles


Subsector : S19 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170558/0001 Project EstablishedICS :National Ref : PR NF X08-014Title : Colours - Colorimetry - Pseudo uniform colour spaces : CIELAB and CIELUV - Colour

difference related formulae



Subsector S21: LABORATORY MEDICINE, CLINICAL PATHOLOGY AND BIOSAFETY

Subsector : S21 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 06301427/0001 Project EstablishedICS :National Ref : 06301427Title : Membrane filters - Part 1: Testing for specific liquid flow rate for flat filter



Subsector S99: UNDETERMINED

Subsector : S99 Registration Date : 2010-10-07Organization : NENCountry : NetherlandsProject ID : 50001596/0001 Project EstablishedICS : 07.100.01National Ref : NTA 8777:2010 Concept nlTitle : Determination of the reduction of the microbiological activity by a composting or

digestion procesScope : This technical agreement gives a method for the determination of 5log10 reduction of

enterococcus faecalis in the digestion status. This method is appicable for the demonstration that a certain composting or digestion installation meet the microbiological requirements.



** End of Sector **




Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING


Subsector T03: ROAD VEHICLES

Subsector : T03 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170409/0001 Project EstablishedICS :National Ref : PR NF R19-601-4Title : Road vehicles . Recommendation for the repair of the motor glazings . Part 4: Repair of

glazing of M3 and N3 vehicles


Subsector : T03 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170410/0001 Project EstablishedICS :National Ref : PR NF R19-601-3Title : Road vehicles - Recommendation for the repair of motor glazing - Part 3 : criteria to

qualify the repair


Subsector : T03 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170411/0001 Project EstablishedICS :National Ref : PR NF R19-601-2Title : Road vehicles - Recommendation for the repair of the motor glazings - Part 2 :

processus to repair the impacts


Subsector : T03 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170412/0001 Project EstablishedICS :National Ref : PR NF R19-601-1Title : Road vehicles - Recommendation for the repair of the motor glazing - Part 1 : criteria to

repair the impacts


Subsector : T03 (Secondary Subsector)

Registration Date : 2010-10-18

Organization : SN

Country : NorwayProject ID : NOT10013/0001 Project EstablishedICS : 43.080.01, 83.160.10National Ref : prNS 5960Title : Snow chains for vehicles classes N2, N3, M2, M3, O3, O4 - Requirements, testing and

markingScope : This standard prescribe requirements and test methodes for snow chains to be mounted on

trucks, busses and their trailers. The standard states minimum requirements to characeristics, driving safety, lifetime, instruction manuals and marking.



Subsector T06: METAL AND PLASTIC CONTAINERS

Subsector : T06 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-16Project ID : P0035400/0002 Draft for public enquiryICS :National Ref : PNE 62353Title : Horizontal cylindrical single skin and double skin steel tanks for the underground and

aboveground storage of liquid, having a diameter larger than 3 000 mmScope : This document arises as complementary to the EN 12285 and collets part of the former

UNE 62350, which is not included in the EN 12285. Specifically it arises for tanks nominal diameter from 3 000 mm up to 4 200 mm and where such a range of volumes is not covered by the EN 12285. It would be desirable to establish a maximum density of the content, which may be limited by 1, 1 Kg/l, equivalent to Class A of the EN 12285.


Subsector : T06 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-16Project ID : P0035658/0002 Draft for public enquiryICS :National Ref : PNE 62351-1:1999/1MTitle : Steel storage tanks for carburant and combustible liquids. Tanks with capacity up to 3

000 litres. Part 1: Single skin tanksScope : This standard modifies the clause 6.3 in order to include a nozzle in the bottom of the tank

for emergency situations.


Subsector : T06 Registration Date : 2010-10-07Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-16Project ID : P0035660/0002 Draft for public enquiryICS :National Ref : PNE 62352:1999/1M

Title : Steel storage tanks for carburant and combustible liquids. Above ground parallelepipedical tanks with capacity up to 2 000 litres.

Scope : This standard modifies the clause 6.3 in order to include a nozzle in the bottom of the tank for emergency situations.



Subsector T14: PACKAGING

Subsector : T14 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 11500842/0001 Project EstablishedICS :National Ref : 11500842Title : Transportation chain for meat and meat products - Stackable reusable transport and

storing crates made of thermoplastic plastics - Part 1: Dimensions, weights, design


Subsector : T14 Registration Date : 2010-10-14Organization : DINCountry : GermanyProject ID : 11500843/0001 Project EstablishedICS :National Ref : 11500843Title : Transportation chain for meat and meat products - Stackable reusable transport and

storing crates made of thermoplastic plastics - Part 2: Performance requirements and tests



Subsector T19: ROAD SAFETY

Subsector : T19 Registration Date : 2010-10-04Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-10Project ID : P0035876/0002 Draft for public enquiryICS :National Ref : PNE 199091-1Title : Road traffic management equipment. Video devices. IP video codification. Functional

specification of communications and protocol for encoders in NCA and decoders in control centers

Scope : This standard is the specification of the functions to fulfil Devices video encoders and decoders to be installed NCA roads and in the Traffic Management Centers respectively


Subsector : T19 Registration Date : 2010-10-04Organization : AENORCountry : Spain Latest Date for Comments : 2010-11-10Project ID : P0035877/0002 Draft for public enquiryICS :National Ref : PNE 199092-1Title : Road traffic management equipment. Video devices. Video manager. Part 1: Functional

specificationScope : This standard is the specification of the functions to fulfil Management applications of IP

video infrastructure to be installed on roads and the Traffic Management Centers, respectively, operation while maintaining compatibility with existing elements (Analogue video matrix).


Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036442/0001 Project EstablishedICS :National Ref : PNE 135360Title : Vertical signs. Road delineators. Junction marker in plastic material. Characteristics,

dimensions and test methods.Scope : This standard defines the particular characteristics, dimensions and test methods applicable

to the vertical delineators made of plastic used in the road sides as a guidance for the road users.

Relatedness :National : REV/AMD UNE 135360:1994 EX

Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036443/0001 Project EstablishedICS :National Ref : PNE 135363Title : Vertical signs. Road delineators. Fixed cylindrical road delineators in plastic material.

Characteristics and test methods.Scope : This standard defines particular characteristics, dimensions and test methods for the

cylindrical delineators made of plastic.


Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036519/0001 Project EstablishedICS :National Ref : PNE 199032-1Title : Road marking equipment. Data capture stations. Functionality and protocols. Part 1:

Functionality standard. Speed x Length traffic data matrix

Scope : The standard (functional Standard and protocols of data traffic stations) defines the provision of traffic data classified by length or speed. This rule is an extension of the same and defines the capacity of these teams to provide information classified by the two criteria simultaneously, composing a table of speeds x lengths


Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036520/0001 Project EstablishedICS :National Ref : PNE 199031-4-2Title : Road marking equipment. Data capture stations. Test methods. Part 4-2:Scope : This document defines the methods of testing for the revision of the Data Traffic Stations.

Covers the functional tests described in the document PNE 199031-3-2 regarding the enlargement of the functional standard that makes reference to the functionality SxL (SpeedxLenght).


Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036626/0001 Project EstablishedICS :National Ref : PNE 199021-1Title : Traffic management equipment. Traffic signal controllers. Part 1: Functional standardScope : This standard defines the functionality required for the traffic signal controllers.

Relatedness :National : REV/AMD UNE 135401-1:1999 EX

Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036627/0001 Project EstablishedICS :National Ref : PNE 199021-2Title : Traffic management equipment. Traffic signal controllers. Part 2: TestingScope : This standard defines test methods for the traffic signal controllers.

Relatedness :National : REV/AMD UNE 135401-2:1999 EX

Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036628/0001 Project EstablishedICS :National Ref : PNE 199021-3Title : Traffic management equipment. Traffic signal controllers. Part 3: Electric characteristicsScope : This standard defines the electric characteristics required for the traffic signal controllers.


Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036629/0001 Project EstablishedICS :National Ref : PNE 199021-4Title : Traffic management equipment. Traffic signal controllers. Part 4: Communications

protocol. Type MScope : This standard defines the type M communication protocol for the traffic signal controllers.

Relatedness :National : REV/AMD UNE 135401-4:2003 IN

Subsector : T19 Registration Date : 2010-10-29Organization : AENORCountry : SpainProject ID : P0036630/0001 Project EstablishedICS :National Ref : PNE 199021-7Title : Traffic management equipment. Traffic signal controllers. Part 7: Communications

protocol type M. TestingScope : This standard defines the test methods for type communication protocol for the traffic

signal controllers.



** End of Sector **




Sector Z : INFORMATION TECHNOLOGY


Subsector Z99: UNDETERMINED

Subsector : Z99 Registration Date : 2010-10-25Organization : AFNORCountry : FranceProject ID : FA170557/0001 Project EstablishedICS :National Ref : PR NF Z67-134Title : Format d'échange de données en assurance maritime et transport



** End of Sector **

2010-08

List of non-electrotechnical subsectors

Sector A: Services

Subsector Title ISO/TC CEN/TC

reference reference

A01 Tourist services / 329; CEN/WS ETO

A02 Cleaning services / 328

A03 Postal services / 331

A04 Transportation services / 320; CEN/WS 016

A05 Maintenance services / 319

A06 Building and construction services / 330

A07 Translation services /

A08 Funeral services / CEN/BT/TF 139

A09 Facility management / 348

A10 Services of Real Estate Agents / CEN/BT/TF 180,

373

A11 Security Services / CEN/BT/TF 167;

391; 384; 370;

CEN/WS 044

A12 Consultancy Services / 395; 381

A99 Undetermined / CEN/WS 002 CEN/WS 004 CEN/WS 037 CEN/WS 039 CEN/WS 041 CEN/WS 051 375; 374; 376; 385 404

Sector B: Building and construction


reference reference

B01 Fire protection 21 70; 72; 191; 192

B02 Structures 59; 98 166; 167; 250; 277;

346; 349 284; 288; 297; 340;

B03 Concrete 71 104; CEN/WS 009

B04 Cement 74; 77 51

B05 Fire tests 92 127

B06 Gypsum / 241

B07 Glass 160 129

B08 Doors and windows 162 33

B09 Thermal matters 163 88; 89; 371

CEN/BT WG 173 CEN/WS 036

B10 Timber structures 165 124

B11 Metal structures 167 135

B12 Masonry 179; 196 125; 246

B13 Solar energy 180 312

B14 Geotechnics 182 341; 396

B15 Sanitary appliances / 163; 7

B16 Taps / /

B17 Lighting equipment and lighting / 50; 169 application technology

B18 Scaffolding / 53

B19 Ceramic tiles 189 67

B20 Drainage equipment / 165

B21 Baths / /

B22 Wallcoverings / 99

B23 District heating / 107

B24 Auxiliary and handicraft work / /

B25 Gas distribution installation and / 234; 235; 282 related equipment

B26 Road building and maintenance / 178; 227

B27 Waterproofing materials / 128; 254; 361; 314

B28 Floor coverings 38/SC 12 134

B29 Aggregates / 154

B30 Floor and surfacing / 217; 303; 323; 390

B31 Heating systems in buildings / 228; 247

B32 Precast concrete products / 177; 229 B33 Building design 205 315; 325; 388

B34 Building and construction – Environmental aspect 350; 351

B99 Undetermined / /

Sector C: Chemicals, chemical engineering and food products


reference reference

C01 Food products 34 174; 275; 302; 360 307; 327; 338; 387 CEN/WS 008 CEN/WS 018

C02 Paints and related products 35 139; 298; 173

C03 Chemistry 47 317; 363

C04 Laboratory glassware 48 332

C05 Lac / /

C06 Essential oils 54 /

C08 Pesticides 81 /

C09 Surfactants 91 276

C10 Starch 93 /

C11 Tobacco 126 401

C12 Glass plant / /

C13 Fertilizers 134 223; 260

C16 Wood preservatives / /

C17 Trees and plants / /

C18 Adhesives / 193

C19 Chemical analysis 201; 202 382; 347

C20 Explosives and firework / 212; 321

C21 Cosmetics 217 392

C99 Undetermined / 386

Sector F: Fundamental standards


reference reference

F01 Technical drawings 10 /

F02 Units & symbols 12 /

F03 Preferred numbers 19 /

F04 Sieves 24 /

F05 Measuring instruments 30; 113 92; 171; 176; 237;

294; 318; 244; 367 141; CEN/WS 011

F06 Terminology principles 37 /

F07 Documentation and information 46 304; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS 006 368

F08 Surfaces / 290

F09 Banking 68 /

F10 Statistics 69 /

F12 Information processing systems 204 224; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365

F13 Environmental tests / /

F14 Graphical technology, 130 / sign-boards and nameplates

F15 Material testing in general 135 138; CEN/WS 007 CEN/WS 021 CEN/WS 033

F16 Graphical symbols 145 /

F17 Administrative documents 154 CEN/WS MMU

F18 Micrographics 171 /

F19 Optics 172; 187 123; 170

F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS 030 362

F21 Value analysis and project / 279 network

F22 Logistics / 379; 273

F23 Energy 203 CEN/CLC/JWG 3 CEN/CLC/JWG 4 CEN/WS 027

F99 Undetermined / 389

Sector H: Products for household and leisure use


reference reference

H01 Cinematography 36 372

H02 Photography 42 /

H03 Consumer questions / 291

H04 Sports equipment 83 136

H05 Oil and gas burners / 47; 131

H06 Horology 114 /

H07 Space heating 116 62; 110; 130; 179; 180

H08 Sizing systems 133; 137 /

H09 Furniture 136 207

H10 Sewing machines 148 /

H11 Heater controls 161 58

H12 Ceramic and glass-ware for food 166 /

H13 Jewellery 174 CEN/WS 047

H14 Caravans 177 245

H15 Toys 181 52

H17 Oil stoves / 46

H18 Central heating boilers / 48; 57; 109; 269

H19 Non-electric cookers and barbecues / 49; 281; 295

H22 Smokers’ lighters and matches / 355; 87

H23 Ladders / 93

H24 Tactile danger warnings / /

H25 Large gas appliances / 106; CEN/CLC/JWG FCGA

H26 Sealing materials / 108; 208

H27 Educational equipment / /

H28 Hunting 191 /

H29 Heat pumps / 113

H30 Equipment for children / 252

H31 Dedicated LPG appliances / 181

H32 Culinary utensils 186 194

H33 Footwear (excluding protective / 309 footwear)

H34 Child safety / CEN/BT/WG 117 398

H99 Undetermined / 299; 364; 369; 402

Sector I: Mechanical engineering


reference reference

I01 Screw threads 1 /

I02 Fasteners 2 185

I03 Limits & fits / /

I04 Rolling bearings 4 /

I05 Iron pipes 5 203

I06 Pressure vessels 11 54

I07 Shafts 14 /

I08 Agricultural machines 23 144, 334

I09 Small tools 29 213

I10 Splines / /

I11 Machine tools 39 142; 143; 145; 255

I12 Pulleys & belts 41 188

I13 Gas containers 58 23; 286

I14 Gears 60 /

I15 Equipment for petroleum industry 67 12

I16 Internal combustion engines 70; 192 270

I17 Machinery in general 72; 199 114; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025

I18 Mining 82 196

I19 Nuclear energy 85 /

I20 Refrigeration 86 44; 182

I21 Chains and chain wheels 100 /

I22 Vacuum technology 112 /

I23 Pumps 115 197

I24 Industrial fans 117 356

I25 Compressors 118 232

I26 Plain bearings 123 /

I27 Earth moving and construction 127; 195 151 equipment

I28 Fluid power 131 /

I29 Gas cleaning / 195

I30 Air distribution / 156

I31 Valves 153; 185 69; 236; 105

I32 Flanges / 74

I33 Information processing in 184 310 automation

I34 Non-ferrous metallic pipes / /

I35 Leisure and recreational machines / 152

I36 Thermoprocessing technology / 186

I37 Printing and paper machines / 198

I38 Leather production, tannery and / 200; 201 related machinery

I39 Machines for metal processing / 202; 322

I40 Industrial piping networks / 267

I41 Membrane filters / 272

I42 Potentially explosive atmospheres / 305

I43 Hydrogen energy 197 /

I44 Nanotechnologies 229 352

I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2

65, 157

Sector M: Metallic materials


reference reference

M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110

M02 Zinc / 209

M03 Foundry technology, 25 190; ECISS/TC 31 ECISS/TC 111 including cast iron

M04 Copper 26 133

M05 Welding 44 121

M06 Dimensions of wrought products / /

M07 Manganese and chromium 65 /

M08 Light alloys 79 132

M09 Iron ores 102 /

M10 Metallic coatings 107 240

M11 Powder metallurgy 119 /

M12 Aluminium ores 129 /

M13 Ferroalloys 132 /

M14 Nickel 155 /

M15 Metallic corrosion 156 262; 219

M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101

M17 Heavy metal ores 183 /

M18 Metal wire products / ECISS/TC 30 CEN/BT/TF 196

378

M20 Tin and tin alloys / 220

M21 Precious metals / 283

M22 Lead and lead alloys / 306

M99 Undetermined / /

Sector N: Non-metallic materials


reference reference

N01 Paper and board 6 172

N02 Solid fuels 27 335; 343;383 CEN/WS 019

N03 Petroleum products 28 19; 336 CEN/WS 038

N04 Refractories 33 187

N05 Textiles 38 189; 248

N06 Rubber 45 218; 366 CEN/WS 003

N07 Sawn timber 55 38; 175

N08 Mica / /

N09 Plastics 61 249

N10 Cork 87 /

N11 Wood-based panels 89 112

N12 Timber products 99 /

N13 Leather 120 289

N14 Plastics pipes 138 155

N17 Fluorspar 175 /

N18 Glass-fibre reinforced plastics / /

N19 Tapes / 253

N20 Ceramics 206 184

N21 Gaseous fuels and combustible gas 158; 193 238

N22 Feather and related materials / 222

N99 Undetermined / /

Sector S: Health, environment and medical equipment


reference reference

S01 Acoustics and sound 43 126; 211 insulation

S02 Transfusion equipment 76 /

S03 Syringes 84 /

S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162 CEN/WS 026

S05 Dentistry 106 55

S06 Vibration & shock 108 231

S07 Anaesthetic and respiratory 121 215 equipment

S08 Air quality 146 137; 243; 264; CEN/CLC WG/CMI

S09 Water quality and water supply 147 164; 230; CEN/WS 001 CEN/WS 034

S10 Surgical implants 150 285; CEN/CLC JWG/AIMD

S11 Contraceptives 157 /

S12 Gas analysis / /

S13 Ergonomics 159 122

S14 Prosthetics 168 /

S15 Surgical instruments 170 /

S16 Aids for the disabled 173 293

S17 Respiratory protective devices / 79

S18 Sterilization of equipment 198 102; 204

S19 First aid equipment and rescue systems / 239

S20 Waste collection, handling and / 183 transportation

S21 Laboratory medicine, clinical 194 140; 206; 233; pathology and biosafety 257; 258; 316 CEN/CLC/TC 3 CEN/WS 031 CEN/WS 053

S22 Energy saving / CEN/WS 005 CEN/WS 015

S23 Personal & property protection against aggression/Burglary protection / 263

S24 Soil quality 190 345; CEN/WS 032

S25 Chemical disinfectants and / 216 antiseptics

S26 Environmental management 207 CEN/WS 040

S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120

S28 Demining / CEN/WS 029 CEN/WS 013

S99 Undetermined / 205; CEN/BT/TF 127 394; 259; 357; 358; 359; 380; 400; 403 CEN/WS PCEC CEN/WS 012 CEN/WS 020

Sector T: Transport, mechanical handling and packaging


reference reference

T01 Shipbuilding and maritime 8; 188 15; 300 structures

T02 Aerospace 20 274; AECMA; ECSS 377

T03 Road vehicles 22 301; 326 CEN/WS IMA

T04 Tyres 31 /

T05 Pallets 51 /

T06 Metal and plastic containers 52 210; 221; 265; 266; 268; 296 393

T07 Glass containers 63 /

T08 Cranes 96 147

T09 Materials handling and 101 148; 149 storage equipment

T10 Freight containers 104 119; 280

T11 Steel wire ropes 105 /

T12 Industrial trucks 110 150; 324

T13 Lifting chains, hooks and ropes 111 168

T14 Packaging 122 261; 120

T15 Cycles 149 333

T16 Lifts & escalators 178 10; 242

T17 Builders hoists / /

T18 Elevating platforms / 98

T19 Road safety / 226; 339

T20 Tram- and railway engineering / 256; / CEN/CLC WG/FPR

T21 Packaging machines / 146

T22 Off-road vehicles / 354

T99 Undetermined / CEN/WS TAF

Sector Z: Information technology


Z01 Radiocommunication for IT / /

Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI

Z03 Common O.S.I. activities / CEN/CLC - EWOS

Z99 Undetermined / 353; CEN/WS DFA CEN/WS DIR CEN/WS EBES CEN/WS ECH CEN/WS ECO CEN/ES EFI CEN/WS ESI CEN/WS FAS CEN/WS FUN CEN/WS IEC CEN/WS JXF CEN/WS LCT CEN/WS LTS CEN/WS MDC CEN/WS MET CEN/WS POR CEN/WS URI CEN/WS XFS CEN/WS ORC CEN/WS CTC CEN/WS XML CEN/WS MEE CEN/WS SCE CEN/WS MES CEN/WS UDP CEN/WS MMI CEN/WS FS2 CEN/WS AUT CEN/WS ICT CEN/WS KMA CEN/WS TEX CEN/WS SAN CEN/WS DPP CEN/WS HIC CEN/WS MLX CEN/WS eGO CEN/WS BII CEN/WS ADN CEN/WS CAT CEN/WS CST CEN/WS DIS CEN/WS ESR CEN/WS EUR CEN/WS FIN CEN/WS GEN CEN/WS ISD CEN/WS NEA CEN/WS NOM

CEN/WS QIS CEN/WS TWE CEN/WS WAC CEN/WS eIN CEN/WS ePR

Monthly Notifications RegisterMonthly Notifications Register Notifications registered at CCMC from...

Documents

Transcript of Monthly Notifications RegisterMonthly Notifications Register Notifications registered at CCMC from...