Montageplan fototoestel
29
http://designforeveryone.howest.be/
-
Upload
anneliesrollez -
Category
Design
-
view
423 -
download
0
Transcript of Montageplan fototoestel
FOTOTOESTEL 2.2
http://designforeveryone.howest.be/
Annelies Rollez / Cesar Vandevelde / Justin Couturon
2/3 weeks (3Dprinting) + 3h 19 minutes112.08 €
http://fototoestel2012.blogspot.be//
ASSEMBLY MANUAL
http://designforeveryone.howest.be/
BILL OF MATERIAL- One 3D printed grip- One 3D printed part for the button- One metal part - One inox part- Button 1 : Druktoets IP67-drukknop zwart- Button 2: IMPULSSCH.WIT- Three Jumper Wires Premium 6" F/F Pack of 10 - Male connector RM 2,54, recht- One bolt M6- Four machine screw M3 x 16
FOTOTOESTEL 2.2
16 different tools
14 standard parts
5 made parts
1DESCRIPTIONDownload the files ‘Handvat.stl’ and‘Hulpstuk_Knop.stl’ , which are available on ourblog (http://fototoestel2012.blogspot.be/).Upload these files on , for example , ‘Shapeways’(http://www.shapeways.com/) and you will seethe prices for these parts instantly.Place the two part in the cart , fill in the deliveryaddress and pay. Within two or three weeks, youwill receive your parts.
FOTOTOESTEL 2.2
Parts files on: http://fototoestel2012.blogspot.be/
2 - 3 weeks
3D printer
2 parts added
88.08 €
No standard parts added
2DESCRIPTIONPrint out the technical plan ‘Onderplaat’ and cutit out .
FOTOTOESTEL 2.2
Technical plan ‘ Onderplaat’ onhttp://fototoestel2012.blogspot.be/3 minutes
A printer and scissors
No standard parts added
No parts added
0 €
3
DESCRIPTIONStick to the back side of the technical plan somedouble-sided tape.
FOTOTOESTEL
Technical plan ‘ Onderplaat’ onhttp://fototoestel2012.blogspot.be/1 minute
Double-sided tape, scissors or cutter
No standard parts added
No parts added
0 €
3
DESCRIPTIONStick the technical plan on a steel plate(thickness 3mm)
FOTOTOESTEL 2.2
Technical plan ‘ Onderplaat’ onhttp://fototoestel2012.blogspot.be/1 minute
No tools
Steel plate (thickness 3 mm)
1 part added
5 €
4
5DESCRIPTIONFix the plat to the table of milling machine andmill this part. Next, four holes , with a diameterof 3 mm, and one hole, with a diameter of 6mm, needs to be drilled
FOTOTOESTEl 2.2
Technical plan ‘ Onderplaat’ onhttp://fototoestel2012.blogspot.be/45 minutes
Milling machine, drilling machine
No standard parts added
No parts added
0 €
6DESCRIPTIONFor the attachment of the handle at the bottomof the camera, a M6 bolt is used.This bolt needs to be shortened with a Dremel orgrinding wheel.
FOTOTOESTEL 2.2
Technical addendum : ‘Bolt’
1 minute
Dremel or grinding wheel
Bolt M6
1 part added
1 €
DESCRIPTIONPrint out the technical plan ‘Plaatje’ and cut itout .
FOTOTOESTEL 2.2
Technical plan ‘Plaatje’ onhttp://fototoestel2012.blogspot.com3 minutes
A printer and scissors
No standard parts
No parts were added
0 €
7
DESCRIPTIONStick to the back side of the technical plan somedouble-sided tape and stick it to a inox plate(thickness 1mm)
FOTOTOESTEL 2.2
Technical plan ‘Plaatje’ onhttp://fototoestel2012.blogspot.be/1 minute
Double-sided tape, scissors or cutter
Inox plate 1mm
1 part added
3 €
8
9DESCRIPTIONFix the plat to the table of milling machine andmill this part. Next , place the part in a foldingmachine, and fold the smaller part of this part.
FOTOTOESTEL 2.2
Technical plan ‘Plaatje’ onhttp://fototoestel2012.blogspot.be/40 minutes
Milling machine, folding machine
No standard parts added
1 part added
0 €
10DESCRIPTIONDrill the hole (diameter 1.5 mm) indicated onthe technical plan. With a Dremel, the slot inthis part could be made.
FOTOTOESTEL 2.2
Technical plan ‘Plaatje’ onhttp://fototoestel2012.blogspot.be/25 minutes
Drilling machine, Dremel
No standard parts added
No parts added
0 €
11DESCRIPTIONFor this step, two standard buttons needs to bepurchased. The technical plan show how thebuttons should be soldered.
FOTOTOESTEL 2.2
Technical addendum : ‘ Connection buttons’, ‘Buttons’ and ‘Connector’15 minutes
Soldering iron
Soldering tin, 2 buttons , 3 x Jumper Wires Premium , Male connector 6 parts added
15 €
12DESCRIPTIONCover the grip (and camera) with paper andpainting tape so that only the button is stillvisible.
FOTOTOESTEL 2.2
No technical plan
3 minutes
Paper, painting tape
No standard parts added
No parts added
0 €
13DESCRIPTIONFirst, spray the button with a plastic primer.After about 15 minutes, the button can besprayed with a black color. Lat the paint drylong enough.
FOTOTOESTEL 2.2
No technical plan
60 minutes
Plastic primer, black paint spray
Plastic primer, black paint spray
No parts added
10 €
14DESCRIPTIONThe grip can be connected to the camera. Usethe technical plan ‘Connection grip –camera‘attached in the technical addendum .
FOTOTOESTEL 2.2
Technical addendum : ‘connection grip –camera’ 1 minute
Spanner
No standard parts
Bolt (step 6 assembly manual)
0 €
TECHNICAL ADDENDUM
http://designforeveryone.howest.be/
ONDERPLAAT
PLAATJE
TWO STANDARD BUTTONS
www.conrad.be
IMPULSSCH.WITBestnummer : 700649 - 89
www.conrad.be
Druktoets IP67-drukknop zwartBestnummer : 700328 - 89
CONNECTOR - WIRES
www.conrad.be
Male connector RM 2,54, rechtBestnummer : 733918 - 89
www.sparkfun.com
Jumper Wires Premium 6" F/F Pack of 10
CONNECTION BUTTONS
Jumper Wires Premium 6" F/F Pack of 10
Druktoets IP67-drukknop zwart
IMPULSSCH.WIT
‘Hulpstuk_Knop’
Jumper Wires Premium 6" F/F Pack of 10
CONNECTION BUTTON - CAMERA
CONNECTION GRIP - CAMERA
CONNECTION GRIP - CAMERA
TEAM CONTACTS
http://designforeveryone.howest.be/
[email protected] +32 474 67 92 84
CESAR. [email protected] +32 496 92 31 84
[email protected] +32 497 99 51 63
BART.GRIMONPREZ @HOWEST.BETEL +32 56 24 12 11
http://designforeveryone.howest.be/
