MONO THERMOSTAT BATH OR SHOWER MIXER W/ STOP VALVE … · (Recommendation: Hot water supply...
1
2. Cover * Cover * Screw Mortar a * Remove the cover after the mortar has dry a Washer Remove & Keep The stop valve is pre-set in factory at center stop position ( Do not turn the spindle during installation) SPECIFICATIONS TROUBLESHOOTING CHECK POINT Temperature is not consistence 1 Remove & clean Handle is loose 2, 3 Tighten PROBLEM SOLUTION Adjust the safety knob on the handle with number 40º in flange, then install the handle 40 Safety knob 1. STRAINER 3. BOLT 2. BOLT Hex. Key INSTALLATION 4. Handle Handle Flange Set water temperature until get 40ºC If get the water temperature at 40ºC, release the handle. Make sure the spindle not rotated. 6. 5. Diverter Cover Nut Cap Bolt Hex. Key 3. Cap Hex. Key Handle Bolt Release The Cap & Bolt ON OFF 40°C Bolt Cap 7. Washer* * The Washer fromInstallation step 2 Handle Spindle Handle Packing R3 "MONO" THERMOSTAT BATH OR SHOWER MIXER W/ STOP VALVE TX451SMBR S06934BR To Bath Spout or Shower Head * Cold Water Supply * Hot Water Supply * 1. PT½ PT½ 200 81 70 55 0 -5 71 +5 0 WALL 140 Minimum Mortar Level Maximum Mortar Level * Pipe supplied by owner Please don't open the thermostat cartridge, because it cause to unstabilize temperature in this product. OPERATING CONDITIONS MAINTENANCE Always wipe chrome plated area with dry soft cloth, and sometimes wipe it with cloth soaked in mild soap. Hot water supply temperature shall be higher by 10 o C. at least, than desired temperature of mixed water. (Recommendation: Hot water supply temperature = 60 o C) 1. 2. Press safety knob turn left to increase temperature over 40 o C. 2. 3. Hot water supply pressure shall be the same or lower than cold water supply . 3. 4. Ensure that water supply is clean ( No Sand, Dirt, Etc.). Water supply pressure : 0.05 ~ 0.75 MPa ATTENTION 1. Use of abrasive cleaning material such as; detergents containing hydrochloric acids, thinner, polishing powder, and nylon brush is not recommended
Transcript of MONO THERMOSTAT BATH OR SHOWER MIXER W/ STOP VALVE … · (Recommendation: Hot water supply...
2. Cover *
Cover *
Screw
Mortar
a
* Remove the cover after the mortar has dry
a
WasherRemove & Keep
The stop valve is pre-set in factory at center stop position ( Do not turn the spindle during installation)
SPECIFICATIONS
TROUBLESHOOTINGCHECKPOINT
Temperature is not consistence 1 Remove & cleanHandle is loose 2, 3 Tighten
PROBLEM SOLUTION
Adjust the safety knob on the handle with number 40º in flange, then install the handle
40
Safety knob
1. STRAINER
3. BOLT
2. BOLT
Hex. Key
INSTALLATION
4.
Handle
Handle
Flange
Set water temperature until get 40ºC
If get the water temperature at 40ºC, release the handle. Make sure the spindle not rotated.
6.5.
Diverter
Cover
Nut
Cap
Bolt
Hex. Key
3.
Cap
Hex. Key
Handle
Bolt
Release The Cap & Bolt
ON
OFF
40°C
BoltCap
7.
Washer*
* The Washer from Installation step 2
Handle
Spindle
Handle
Packing
R3
"MONO" THERMOSTAT BATH OR SHOWER MIXER W/ STOP VALVE TX451SMBR
S06934BR
To Bath Spoutor Shower Head *
Cold Water Supply *
Hot Water Supply *
1.
PT½
PT½
20081
70 55 0-571+5 0
WA
LL
140
Minimum Mortar LevelMaximum Mortar Level
* Pipe supplied by owner
Please don't open the thermostat cartridge, because it cause to unstabilize temperature in this product.
OPERATING CONDITIONS
MAINTENANCEAlways wipe chrome plated area with dry soft cloth, and sometimes wipe it with cloth soaked in mild soap.
Hot water supply temperature shall be higher by 10oC. at least, than desired temperature of mixed water.(Recommendation: Hot water supply temperature = 60oC)
1.2.
Press safety knob turn left to increase temperature over 40oC.2.3.
Hot water supply pressure shall be the same or lower than cold water supply .
3.
4. Ensure that water supply is clean ( No Sand, Dirt, Etc.).
Water supply pressure : 0.05 ~ 0.75 MPa
ATTENTION1. Use of abrasive cleaning material such as; detergents
containing hydrochloric acids, thinner, polishing powder, and nylon brush is not recommended
