The classic concrete bold roll tile in the Mediterranean tradition

Monarch page 1

Marley Monarch

Description & Technical data 7 pages

Inland KwaZulu-Natal Western Cape

Tile range, Fittings & Accessories

Nominal tile size: 420 x 332 mm

Nominal hanging length: 390 mm

Nominal tile mass: 5 kg

Nominal cover width 301 mm

Monarch page 3

at lock mid-shuffl e position:

Undertile membrane

Technical data

Minimum roof pitch with 100 mm headlap with 75 mm headlap

The side interlock provides for apractical 2 mm play between the tiles(± 1 mm either way of the nominal cover)which gives fl exibility when setting outthe roof and helps to achieve the correctperpendicular alignment of the courses.

17,5˚ 26˚

Rafter/Trusses As per structural requirements

Rafter centres 760 mm with 38 x 38 mm batten(maximum) 900 mm with 38 x 50 mm batten fi xed fl at 1 000 mm with 38 x 50 mm batten on edge

Note: Above 760 mm the rafter spacing can be increased only withengineer-designed trusses and with 38 x 50 mm batten of the correctgrade. All structural timber must comply with S.A National Standards.

Marley high-quality Undertile Membrane is recommended in all cases.Modern practice has demonstrated that the undertile membrane is a fundamental part of a tiled roof at pitches below 26° and for pitches above 45°, and at all pitches in exposed and coastal areas.

Tiling data at pitches of 17,5° to 25°

Tiling data at pitches of 26° and above

Minimum tile headlapMaximum batten centresBatten per m² (net length)Tiles per m² (net)Mass of tiles per m² ±

100 mm320 mm3,13 m10,4851,9 kg

Minimum tile headlapMaximum batten centresBatten per m² (net length)Tiles per m² (net)Mass of tiles per m² ±

75 mm345 mm2,9 m9,6348,2 kg

Distance from top edge of fi rst battento outside edge of fascia board

Distance from top edge of top batten to rafter apex

Estimating See Eaves and Rafter tables

335 mm

25 mm

All tiling and fi xing to comply with SANS 10062 : 2003 Code of Practice and with Marley standard fi xing specifi cations.

Cutting and drilling of tiles: See Health & Safety instruction

45˚

26˚

17,5˚

1. The minimum pitch and minimum headlap must not be reduced under any circumstance. It is always better to raise the safety factor of the roof by adding a full course of tiles and increasing the tile headlap evenly on the rafter length.2. In exposed areas the tile headlap may be increased, but greater lap is not as effective as a steeper pitch.

Number of tiles on the rafter length at minimum headlap

Roof pitches of:

17,5º to 25º 26º and more 100 mm headlap 75 mm headlap

Rafter length Rafter length

1m

2m

3m

4m

5m

6m

7m

8m

9m

10m

11m

12m

Rafter Table

Eaves Table

The Rafter Table indicates the number of coursesto be allowed on the rafter length to ensure thatthe minimum tile headlap of 100 mm or 75 mmis obtained according to the roof pitch.

The Eaves Table shows the average linearcoverage for Monarch tiles along the eaves length.Calculations are given at lock mid-shuffl e position,subject to standard manufacturing tolerances.

All fi gures are net. Wastage must be added.

© Marley Roofi ng 2010

1

2

3

4

5

6

7

8

9

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

10

11

12

13

14

15

16

17

18

19

1

2

3

4

5

6

7

8

9

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

10

11

12

13

14

15

16

17

18

19

0,360

0,680

1,000

1,320

1,640

1,960

2,280

2,600

2,920

3,240

3,560

3,880

4,200

4,520

4,840

5,160

5,480

5,800

6,120

6,440

6,760

7,080

7,400

7,720

8,040

8,360

8,680

9,000

9,320

9,640

9,960

10,280

10,600

10,920

11,240

11,560

11,880

12,200

0,360

0,705

1,050

1,395

1,740

2,085

2,430

2,775

3,120

3.465

3,810

4,155

4,500

4,845

5,190

5,535

5,880

6,225

6,570

6,915

7,260

7,605

7,950

8,295

8,640

8,985

9,330

9,675

10,020

10,365

10,710

11,055

11,400

11,745

12,090

Above 45º pitchconsult themanufacturer

11,77

0

12,07

1

12,37

2

12,67

3

12,97

4

13,27

5

13,57

6

13,87

7

14,17

8

14,47

9

14,78

0

15,08

1

15,38

2

15,68

3

15,98

4

16,28

5

16,58

6

16,88

7

17,18

8

17,48

9

17,79

0

18,09

1

18,39

2

18,69

3

18,99

4

19,29

5

19,59

6

19,89

7

20,19

8

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

12m 13m 14m 15m 16m 17m 18m 19m 20m

300

.

32 300

332

332. . . .300

. . ...

.

75

..

.

30

.

....

420

.

.

Monarch M22-coated

Monarch Designer Range

The superior performance proven M22-coated tile provides guaranteed long-lastingcolour uniformity on the roof. Acid-rain tested, formulated to prevent algal and fungalgrowth, it is recommended for all applications − Highly suitable for humid coastal regions

The Monarch Designer Range enables architects and developers to create strikinglybeautiful roofs in the classic mediterranean tradition with standard or special blends.

Monarch page 5

For beautiful roofs in the classic Mediterranean tradition

Monarch page 7

Next...

Tuscany special Blend

MONARCH INLAND — FITTINGS and ACCESSORIES

Quality corrosion-resistant integrated stormclipsmanufactured from ZIAL

‘SOLO-FIX’ stormclips

®

Monarch tile: Code 85-48 S

Packaging: 500 clips per box

It is important to use the correct clip for the tile

profile.

Undertile membrane

Colour: White traditionalNet coverage per roll 45 m²Printed 150 mm headlap dotted line

Monarch tile minimum length 90 mm

M22 touch-up coatingfor mortarbedding, flashings, fascia boards

etc. per 1, 2 and 5 litre

2 ply 400 micron polypropylene laminate

Mortar pigment in all colours per kg

Tile nails

Agrément Certificate 2008/341

All tile accessories, undertile membrane, tiling nails, stormclips, pigment,

M22 touch up coating etc.are available ex-factory.

2 ply 400 micron polypropylene laminatewith insulation foil

Agrément Certificate 2007/333

Printed 150 mm headlap dotted line

• HEAVY INDUSTRIAL — Reinforced two sided foil

Agrément Certificate 2009/353

Agrément Certificate 2009/353

• RESIDENTIAL — One sided foil

• RESIDENTIAL/COMMERCIAL — Two sided foil

Net coverage per roll 45 m²

Net coverage per roll 45 m²

Net coverage per roll 50 m²

Marley ‘Radiant Barrier’

97% heat reflective

Energy saving

Serrated nails for rake verge tiles 75 mm

Next... KwaZulu-Natal Range

Overlapping fittings

Taper ridge tile2,7 per m

Ventilated ridge tile Rake verge tile3,2 per m

Taper hip starter120º capped

ridge tile 2,3 per m

Butt joint fittings

120º ridge tile 2,2 per m

MarleyUniversalRidge Tile System

MarleyUniversal

RakeVerge TileSystem

Monoridge tile2,7 per m

MONARCH KWAZULU-NATAL FITTINGS and ACCESSORIES

Quality corrosion-resistant integrated stormclipsmanufactured from ZIAL

‘SOLO-FIX’ stormclips

®

Monarch tile: Code 85-48 S

Packaging: 500 clips per box

It is important to use the correct clip for the tile

profile.

Undertile membrane

Colour: White traditionalNet coverage per roll 45 m²Printed 150 mm headlap dotted line

Minimum length for Monarch tile 90 mm

M22 touch-up coatingfor mortarbedding, flashings, fascia boards

etc. per 1, 2 and 5 litre

2 ply 400 micron polypropylene laminate

Mortar pigment in all colours per kg

Tile nails

Agrément Certificate 2008/341

All tile accessories, undertile membrane, tiling nails, stormclips, pigment,

M22 touch up coating etc.are available ex-factory.

2 ply 400 micron polypropylene laminatewith insulation foil

Agrément Certificate 2007/333

Printed 150 mm headlap dotted line

• HEAVY INDUSTRIAL — Reinforced two sided foil

Agrément Certificate 2009/353

Agrément Certificate 2009/353

• RESIDENTIAL — One sided foil

• RESIDENTIAL/COMMERCIAL — Two sided foil

Net coverage per roll 45 m²

Net coverage per roll 45 m²

Net coverage per roll 50 m²

Marley ‘Radiant Barrier’

97% heat reflective

Energy saving

Serrated nails for rake verge tiles 75 mm

Next... Western Cape Range

Overlapping fittings

Taper ridge tile2,5 per m

Ventilated ridge tileRake verge tile3,2 per m

Taper terminal ridge tile

Taperhip starter

120ºcapped ridge tile2,3 per m

Halfround capped ridge tile1,9 per m

Butt joint fittings

120ºridge tile2,2 per m

Ventilated ridge tile

Shellhip starter

120ºterminalridge tile

90ºridge tile 2,2 per m

Monoridge tile 2,2 per m

MarleyUniversalRidge Tile System

MarleyUniversal

RakeVerge TileSystem

MONARCH WESTERN CAPE FITTINGS and ACCESSORIES

Quality corrosion-resistant integrated stormclipsmanufactured from ZIAL

‘SOLO-FIX’ stormclips

®

Monarch tile: Code 85-48 S

Packaging: 500 clips per box

It is important to use the correct clip for the tile

profile.

Undertile membrane

Colour: White traditionalNet coverage per roll 45 m²Printed 150 mm headlap dotted line

Monarch tile 100 mm

M22 touch-up coatingfor mortarbedding, flashings, fascia boards

etc. per 1, 2 and 5 litre

2 ply 400 micron polypropylene laminate

Mortar pigment in all colours per kg

Agrément Certificate 2008/341

All tile accessories, undertile membrane, tiling nails, stormclips, pigment,

M22 touch up coating,DPC, birdcomb etc.

are available ex-factory.

2 ply 400 micron polypropylene laminatewith insulation foil

Agrément Certificate 2007/333

Printed 150 mm headlap dotted line

• HEAVY INDUSTRIAL — Reinforced two sided foil

Agrément Certificate 2009/353

Agrément Certificate 2009/353

• RESIDENTIAL — One sided foil

• RESIDENTIAL/COMMERCIAL — Two sided foil

Net coverage per roll 45 m²

Net coverage per roll 45 m²

Net coverage per roll 50 m²

Marley ‘Radiant Barrier’

97% heat reflective

Energy saving

Serrated nails

Rake verge tiles 75 mm

Back to Quickfinder

Overlapping fittings

Taper ridge tile 2,5 per m Rake verge tile 3,2 per m

Taperhip starter

Butt joint fittings

120º ridge tile 2,2 per m

Monoridge tile 2,7 per m

Butt joint hip starter

MarleyUniversalRidge Tile System

MarleyUniversal

RakeVerge TileSystem

Use only serrated nails in Western Cape coastal regions

Monarch Antique TerracottaMOANTC

Please note:Photographs are given as an indication only.Due to environmental factors such as light and weatherand the limitations of colour reproduction actualsamples should always be seen before ordering.