757575www.fiberlay.com 75

MOLD RELEASE WAX & PARTING FILMS BY REXCO ......................... 76

MOLD RELEASE WAX BY GRIGNARD .............................. 77

ORCA MOLD RELEASE SEMI PERMANENT SYSTEMS .... 77

MOLD RELEASE PRODuCTS ...... 78

Mold Wax & Release Agents

Mold W

ax & R

elease Agents

10_MoldRelease.indd 75 1/4/11 2:57 PM

PARTALL® COvERALL FILMThis product is a new non-hazardous, low VOC water-based polyvinyl alcohol (PVA) coating that acts as a barrier between parts and reactive mold surfaces. It is recommended for use on seasoned molds as extra protection against remolding problems. Higher solids content aids production efficiency by providing greater protection with fewer coats.

Partall® Coverall Film may be applied by brush, roller, sponge, cloth or spray. Improved formulation enhances use – no fisheyes or cob webbing, self leveling and faster dry film build up. Available in purple or clear.PRODuCT # DESCRIPTION254108 COVerAll lOw VOC CleAr QuArT254110 COVerAll lOw VOC CleAr GAllOn254113 COVerAll lOw VOC CleAr 5-GAl255G COVerAll lOw VOC PurPle GAllOn

PARTALL® PASTE #2This is the original “green” wax. It is an economical paste wax mold release formulated with hydrocarbon and microcrystalline waxes. Designed as a general purpose mold release agent on fiberglass and metal molds and as a smooth compatible prime coat for PVA coatings.252215 24 Oz. MeTAl CAn252207 7 lb PlAsTIC COnTAIner252225 25 lb PlAsTIC COnTAIner

FIBERLEASEThis is a water/alcohol based polyvinyl alcohol (PVA) mold release agent that forms a barrier between parts and mold surfaces that are still curing (green or recently reconditioned molds can be reactive). FIberleAse, the original green parting film, is resistant to solvents and styrene yet is water soluble. May be used with polyester, vinyl ester, epoxy and urethane resins. PVA is most commonly applied over mold release wax. It can also be used as a surface cure agent during gel coat repairs. It may be applied by brush, roller, sponge, cloth or spray. 2544 4 Oz. FIberleAse 4 Oz.254P PInT FIberleAse PInT254Q QuArT FIberleAse QuArT254G Green GAllOn254CG CleAr GAllOn

Mold Release Wax and Parting Films

MOLD MAGIC: HIGH PERFORMANCE MOLD RELEASE PASTE WAX This product is a high performance paste wax formulated utilizing the highest quality carnauba wax and semi-permanent technology to provide a durable, glossy release surface pull after pull yielding the highest shine and finish on the molded part. Mold Magic assist in maintaining an efficient and profitable molding operation with its ease of application and performance. Mold Magic may be utilized in a variety of molding operations usch as hand lay-up, casting, rTM, pre-pregs, vacuum bagging, bMC, sMC, and filament winding for most thermoset resins such as: polyester, epoxy, vinyl ester, DCPD, phenolic, melamine, and polyurethane. High temp up to 500°F.

252114 GrIGnArD MOlD MAGIC MOlD releAse wAX, 14 OunCe

MO

LD W

AX

& R

ELEA

SE A

GEN

TS

www.fiberlay.com76

10_MoldRelease.indd 76 1/4/11 2:57 PM

ORCA GC1: Semi-permanent Dry Film TechnologyThis product has been formulated with a cross linking polymer technology to improve release quality and durability. It provides a hard, glossy, smooth film which allows multiple molding cycles and maximizes production. It is composed of a proprietary blend of polymers which holds its integrity under extreme molding conditions. It provides a reproducible molded part with superior luster. It is economical in use while maintaining excellent performance. GC1 is recommended for most molding processes which include: hand lay-up, cultured marble, solid surface, casting, compression / injection molding, polymer concrete, resin transfer, filament winding, extrusion and pressing. GC1 may be utilized in the molding of a variety of thermoset and thermoplastic resins and gel coats such as: polyester, DCPD, epoxy, vinyl ester, phenolic, PVC, PP, Pe, Pu, and acrylic.252205 OrCA GC1 seMI-PerMAnenT DrY FIlM, GAllOn

ORCA SKIN: High Performance Liquid Wax Release AgentThis product is a carnauba wax release agent incorporating semi-permanent chemistry in liquid form. OrCA sKIn is formulated to clean during application eliminating premature wax buildup by spreading the wax uniformly on the mold. OrCA sKIn utilizes the highest quality carnauba wax in order to provide a durable, glossy release surface pull after pull. The release coating provides excellent slip with long-lasting characteristics and minimal transfer. It may be used when molding a variety of thermoset resins such as: polyester, gel-coat, epoxy, vinyl ester, DCPD, phenolic, melamine, and polyurethane. Molding processes include: Hand lay-up, Casting, rTM, Pre-pregs, Vacuum bagging, bMC, sMC, and Filament winding.252204 OrCA sKIn lIQuID wAX releAse, GAllOn

ORCA SLIP: High Slip / Semi-permanent Mold Release AgentThis product uses a cross linking polymer technology which reduces user costs by improving the mold treatment process. It combines mold release with multiple pulls, high slip qualities and durability when molding intricate parts. OrCA slIP has a short cure time for fast turnover and does not require a sealer. It utilizes a proprietary release polymer blended into a rapidly evaporating carrier. This carrier functions to dissolve the release agent, dispersing it uniformly throughout the mold surface while preventing premature buildup. OrCA slIP can be used for both gel-coated and non-gel-coated molding applications including: hand lay-up, mandrel molding, solid surface, casting, compression molding, polymer concrete, resin transfer, extrusion, encapsulation and pressing. It may be utilized for most thermoset and thermoplastic resins and gel coats such as polyester, DCPD, epoxy, vinyl ester, melamine, phenolics, Pu, Abs, nylon, PVC, PP, Pe, and acrylic.252201 OrCA slIP MOlD releAse AGenT, GAllOn

ORCA SEAL: High Performance SealerThis product utilizes the maximum amount of a proprietary conditioner to fill imperfections in the mold surface of new and seasoned molds. A hard smooth surface remains after treatment that is compatible with all mold release agents. It provides a superior finish to the molded part and ensures parts reproducibility. OrCA seAl has long lasting characteristics while maximizing performance of the release agent. It may be utilized as a base coating when molding most thermoset and thermoplastic resins and gel coats such as polyester, DCPD, vinyl ester, epoxy, phenolics, Pu, Abs, nylon, PVC, PP, Pe, and acrylic.252203 OrCA seAl HIGH PerFOrMAnCe seAler, GAllOn

ORCA CLEAN: Fast Evaporating / Extreme CleaningThis product is a proprietary blend of unique solvents formulated to dissolve and remove all resin buildups of mold release agents from the mold surface. This high performance cleaner may be utilized to clean all application equipment such as spray guns, tips and hoses, provided that seal compatibility is confirmed.252102 OrCA CleAn HIGH PerFOrMAnCe CleAner, GAllOn

ORCA SHIMMER: High Temp Mold Release WaxOrCA sHIMMer High Temp Mold release wax for Fiberglass Applications is a blending of carnauba, synthetic waxes and thermoresins to provide consistent performance in high temperature molding. OrCA sHIMMer High Temp Mold release wax for high gloss finished parts.271100607 OrCA sHIMMer MOlD releAse wAX HI TeMP, 11 Oz.

MO

LD W

AX &

RELEA

SE AG

ENTS

www.fiberlay.com 77

10_MoldRelease.indd 77 1/4/11 2:57 PM

E236 uRETHANE RELEASE A highly versatile silicone release agent sold in an aerosol spray can.

E302 ROCKET RELEASE A versatile non-silicone based release agent. Does not hinder paint adhesion when properly cleaned from cast parts. sold in an aerosol spray can.

A324 RAPID RELEASE A release agent designed for releasing silicone rTV from silicone rTV. useful for releasing other materials such as urethane and epoxy. sold in an aerosol spray can.

E497 THERMOSET RELEASEA specially formulated release agent and anti-stick lubricant for molded thermoset plastics, rubber, and similar materials. It allows molded parts to be painted, plated, hot-stamped, adhesive bonded, labeled, or otherwise decorated.

CHALLENGE 90 Our most popular liquid release for use in parting rigid and flexible foams. It is also used for elastomer surfaces that require painting.

RF-5124 (PvC) A polyvinyl chloride material that forms a parting film which is not sensitive to moisture since it is a solvent soluble system.

SYNLuBE™ MOLD RELEASES sacrificial mold release agents for the rubber, resin, plastic, polyurethane and tire building industries. synlube products are available as silicone and non-silicone releases, and in either bulk or aerosol containers. synlube release agents are suitable for vertical or horizontal surfaces.

Smooth-On Release Agents Qs Code 2526...

A full range of release agents to cover many applications. Aerosols and non-Aerosol, solvent based or water based; made especially for Mold Making and Casting.

ONE STEPTM release Agent And sealer seals and releases porous originals in one step.

EASE RELEASE® release Agent covers nearly every mold making and casting application.

IN & OuT® II water based Concrete release Agent is an economical concentrate for releasing concrete castings from smooth-On rubber molds. Does not affect surface detail of castings. Prolongs mold life.

uNIvERSAL MOLD RELEASE® will release polyurethane mold rubbers from properly prepared models. not for use with silicones.

Polytek Development Corp. Qs Code 2526...

LATEX, POLYuRETHANES, SILICONES & EPOXIESPolytek has formulated a range of materials to help you achieve your molding and casting objectives, and we are constantly working to invent new products to make your job easier.

Polytek offers the most complete line of mold making and casting materials available anywhere. For mold making, Polytek produces polyurethane and silicone liquid rubbers in many hardnesses as well as latex, alginate and wax. For casting, Polytek manufactures rigid and flexible polyurethane plastics and foams and castable epoxies.

Mold Releases Qs Code 2711...

PuMA Polymers Qs Code 2641...

Huntsman Advanced Materials Qs Code 2509...

REN MATERIALS - EPOXY, uRETHANE & BOARDSleading global supplier of synthetic and formulated polymer systems for customers requiring high performance materials which outperform the properties, functionality and durability of traditional materials.

MO

LD W

AX

& R

ELEA

SE A

GEN

TS

www.fiberlay.com78

10_MoldRelease.indd 78 1/4/11 2:57 PM