Module 9: Installing and Configuring Network Load Balancing.
-
Upload
jordan-gibson -
Category
Documents
-
view
227 -
download
0
Transcript of Module 9: Installing and Configuring Network Load Balancing.
Overview
Pre-Installation
Network Load Balancing Driver Installation
Configuring the Network Load Balancing Driver
Cluster Parameters
Host Parameters
Port Rules
TCP/IP Properties
Post-Installation Configuration
Pre-Installation
Verify that aggregate subnet throughput supports IP traffic
Verify that the throughput of each host is documented
Verify that cluster members support client throughput
Verify that all IP addresses are manually allocated
Verify that TCP/IP is bound to the network card
Hardware Considerations
No special hardware requirements
Ethernet or FDDI
All hosts on one broadcast subnet
All host on one Level 2 switch or VLAN
All hosts on a single hub or repeater
Two NICs per host preferred:
One NIC for cluster traffic and heartbeats
One NIC for replications/backend access
Controlling Switch Flooding
Hosts on individual ports results in switch flooding
Hosts on a hub limits switch flooding
Cluster hostCluster host
Non-Cluster hostNon-Cluster host
Layer 2 switchLayer 2 switch
Layer 1 hubLayer 1 hub
HubHub
Cluster hostCluster host
Non-Cluster hostNon-Cluster host
Layer 2 switchLayer 2 switch
Network Load Balancing Driver Installation
Select Driver
Configure – Cluster Parameters Host Parameters Port Rules
Exit Dialog Box
NLB Cluster Host 1 Properties
General
Connect using:
Configure
Description
Sharing
Intel® PRO/100+ Management Adapter
Components checked are used by this connection:
Client for Microsoft NetworksNetwork Load BalancingNetwork Monitor DriverInternet Protocol (TCP/IP)
Install… Uninstall Properties
This component provides TCP/IP load balancing functionality.
Show icon in taskbar when connected
CancelCancelClose
Configuring the Network Load Balancing Driver
Port Rules control response to traffic
Host Parameters apply to default traffic
Cluster Parameters apply to the cluster
Network Load Balancing Properties
Cluster Parameters
Primary IP address 1 . 1 . 1 . 100
Subnet mask 255 . 255 . 255. 0
Full Internet name cluster.domain.com
Network address 02-bf-01-01-01-64
Multicast support enabled
Remote password
Confirm password
Remote control enabled
Please consult on-line help forconfiguration information
Host Parameters
OK
Port Rules
Help
Cancel
Cluster Parameters
Set Cluster IP
Set Cluster Internet name
Select Multicast
Enable Remote Control
Network Load Balancing Properties
Cluster Parameters
Primary IP address 1 . 1 . 1 . 100
Subnet mask 255 . 255 . 255. 0
Full Internet name cluster.domain.com
Network address 02-bf-01-01-01-64
Multicast support enabled
Remote password
Confirm password
Remote control enabled
Please consult on-line help forconfiguration information
Host Parameters
OK
Port Rules
Help
Cancel
Host Parameters
Set Unique ID
Set initial state
Set Dedicated IP Address
Network Load Balancing Properties
Cluster Parameters
Priority (Unique host ID) 1
Initial cluster state active
Dedicated IP address 1 . 1 . 1 . 101
Subnet mask 255 . 255 . 255 . 0
Host Parameters
OK
Port Rules
Cancel
Port Rules
Set Port Range and Protocol for this rule
Set or Modify parameters
Add, Modify, or Remove a rule
Select or view list of rules
Network Load Balancing Properties
Cluster Parameters
Port range 80 to 80
Host Parameters Port Rules
Protocols TCP UDP Both
Filtering mode
Multiple hosts
Single host
Disabled
Affinity None Single Class C
Load weight 50 or Equal
Handling priority 1
Add Modify Remove
Start End Protocol Mode Priority Load Affinity80 80 Both Multiple Equal None443 443 Both Multiple Equal None
Filtering Mode
Set Filtering mode
For Single Host set Handling Priority
Network Load Balancing Properties
Cluster Parameters
Port range 80 to 80
Host Parameters Port Rules
Protocols TCP UDP Both
Filtering mode
Multiple hosts
Single host
Disabled
Affinity None Single Class C
Load weight 50 or Equal
Handling priority 1
Add Modify Remove
Start End Protocol Mode Priority Load Affinity80 80 Both Multiple Equal None443 443 Both Multiple Equal None
Affinity
Select Affinity mode for client IP
Network Load Balancing Properties
Cluster Parameters
Port range 80 to 80
Host Parameters Port Rules
Protocols TCP UDP Both
Filtering mode
Multiple hosts
Single host
Disabled
Affinity None Single Class C
Load weight 50 or Equal
Handling priority 1
Add Modify Remove
Start End Protocol Mode Priority Load Affinity80 80 Both Multiple Equal None443 443 Both Multiple Equal None
Load Weighting and Priority
Select equal load distribution or manual load distribution
Network Load Balancing Properties
Cluster Parameters
Port range 80 to 80
Host Parameters Port Rules
Protocols TCP UDP Both
Filtering mode
Multiple hosts
Single host
Disabled
Affinity None Single Class C
Load weight 50 or Equal
Handling priority 1
Add Modify Remove
Start End Protocol Mode Priority Load Affinity80 80 Both Multiple Equal None443 443 Both Multiple Equal None
TCP/IP Properties
Enter cluster dedicated IP address for single NIC configuration, enter primary IP or dedicated IP addresses for multiple NIC configurations
Enter additional IP addresses in the Advanced dialog box
Internet Protocol (TCP/IP) Properties
General
You can get IP settings assigned automatically if your network supportsthis capability. Otherwise, you need to ask your network administrator forthe appropriate IP settings.
OK Cancel
Obtain an IP address automatically
Use the following IP address:
IP address 1 . 1 . 1 . 101
Subnet mask 255 . 255 . 255 . 0
Default gateway 1 . 1 . 1 . 1
Advanced…
Obtain DNS server address automaticallyObtain DNS server address automatically
Use the following DNS server addresses:
Preferred DNS server:
Alternate DNS server:
Post-Installation Configuration
Internet Protocol (TCP/IP) Properties
General
You can get IP settings assigned automatically if your network supportsthis capability. Otherwise, you need to ask your network administrator forthe appropriate IP settings.
OK Cancel
Obtain an IP address automatically
Use the following IP address:
IP address 1 . 1 . 1 . 101
Subnet mask 255 . 255 . 255 . 0
Default gateway 1 . 1 . 1 . 1
Advanced…
Obtain DNS server address automaticallyObtain DNS server address automatically
Use the following DNS server addresses:
Preferred DNS server:
Alternate DNS server:
Network Load Balancing Properties
Cluster Parameters
Port range 80 to 80
Host Parameters Port Rules
Protocols TCP UDP Both
Filtering mode
Multiple hosts
Single host
Disabled
Affinity None Single Class C
Load weight 50 or Equal
Handling priority 1
Add Modify Remove
Start End Protocol Mode Priority Load Affinity80 80 Both Multiple Equal None443 443 Both Multiple Equal None