March 2009

MITSUI PARTS REFERENCE MANUAL

MODELS:MSG-200MH MSG-205MHMSG-250MH

March 2009

Table of Contents3. General parts for 200/205/250MH5. Accessories for 200/250MH7. Cross feed for 200/250MH8. Fine cross feed attachment for 200/250MH

11. Vertical feed for 200/250MH12. Fine vertical feed for 200/205/250MH14. Spindle head for 200/250MH16. Longitudinal feed parts for 200/205/250MH18. Coolant cover

Pg. 1

March 2009

Use of Parts Reference Manual

1. When ordering referenced parts you should now use part numbers to identify parts. Pictures are provided to clearly identify parts or assemblies.

2. Your part orders must include machine model and serial number for correct identification.

3. This manual is intended to be a reference to facilitate identifying and parts for Mitsui grinders. It is limited to the most commonly required parts and units. If you cannot identify a part quickly with this manual please contact your local distributor.

4. All photos are for reference only. Your part may differ from the photos.

5. You can also contact Mitsui High-tec (USA) for technical support (847-593-1634 x101 or x110)

Pg. 2

March 2009

GENERAL PARTS FOR 200/205/250MHCOLUMN DUST SHIELDFOR 200 P/N: CDS200

FOR 250 P/N : CDS250

WHEEL GUARD 8” P/N: WG8

CROSSFEED HAND WHEELFOR200M P/N: HWCF FOR 250M P/N : HWVF

HANDLE GRIP P/N: HGRIP

VERT. FEED HAND WHEELP/N: HWVF

SPINDLE OFF SWITCHP/N: ME2002

SPINDLE ON SWITCHP/N : ME2001

CONTROL BOXP/N:CB220

CB440

L/F HAND WHEELP/N:HWLG

TABLE END GUARDFOR 200 P/N :ML2009FOR250 P/N : ML2509

LEVELING PLATESP/N : MG2001

GUIDE PLATE FOR DUST SHIELDFOR 200 P/N :MV2010N FOR 250 P/N: MV2510N

TABLE STOPPER P/N :ML2001

SADDLE STOPPER P/N :MC2007

HAND WHEEL L-NUT-ML2003

CROSS FEED V WAY WIPERFOR 200MH P/N:VW200FOR250MH P/N:VW250

RUBBER MAT FOR 200 P/N: MG2004FOR 250 P/N : MG2005

WASHER P/N : MG2003

Pg. 3

CAP NUT P/N :MG2002

FOLD DOWN P/N: HGRIPF

SPRING WASHER, L/F – ML2002

March 2009

200MH 205MH 250MH

1 Guide Plate For Column Dust Shield(New) MV2510N2 Column Dust Shield CDS2503 Table End Guard ML25094 Hand Wheel Lock Nut for L/F5 Spring Washer for L/F6 Hand Wheel For Longitudinal Feed7 Hand Wheel For Cross Feed HWVF8 Hand Wheel For Vertical Feed9 Handle Grip

10 Handle Grip - Fold Down11 Cap Nut for Hand Wheel12 Washer for Hand Wheel13 Table Stopper 14 Saddle Stopper15 Rubber Mat for Saddle MG200516 Vee Way Wiper (4 Pcs.Set) VW25017 Control Box Std. 220V18 Control Box Std. 460V19 Spindle ON Switch(New)20 Spindle OFF Switch(New)21 Leveling Plate (3 Pcs Set)

ML2003ML2002

MV2010NCDS200ML2009

MG2004VW200

MG2002MG2003ML2001MC2007

HGRIPF

HWLGHWCF

HWVFHGRIP

MG2001

CB220CB460

ME2001ME2002

Pg. 4

March 2009

Accessories for 200/250DUST SCOOPP/N - DS

ONE SHOT LUBRICATORP/N - MANLUB

OVER WHEEL DRESSERFOR 8” P/N - OTW8FOR 12” P/N – OTW12

BALANCING STAND & ARBORFOR 8” P/N – BSA8FOR12” P/N – BSA12

WHEEL ADAPTER FOR 8”STANDARD - P/N – WA8BALANCIN - P/N – BWA8 WHEEL ADAPTER WRENCH

P/N –MA2001 P/N – MA2002

Pg. 5

March 2009

S/N DESCRIPTION Part Number

1 Dust Scoop DS2 Over The Wheel Dresser for 8" Wheel OTW83 Over The Wheel Dresser for12" Wheel OTW124 Balancing Stand & Arbor for 8" Wheel BSA85 Balancing Stand & Arbor for 12" Wheel BSA126 Wheel Adapter Std.for 8" Wheel WA87 Wheel Adapter Bal.for 8" Wheel BWA88 Wheel Adapter Bal.for12" Wheel BWA129 One Shot Lubricator MANLUB

10 Wheel Adapter Wrench(Hook Type) MA200111 Wheel Adapter Wrench(Vee Type) MA2002

Mitsui Accessories

Pg. 6

March 2009

Cross Feed For 200/250MHCROSS FEED SCREW & BUSHINGSTD For 200/205 –P/N: CF200

FINE For 200/205 – P/N: FC200

CROSS FEED BALL SCREWSTD. FOR 200 – P/N – CFBS200, FOR 250 – CFBS250FINE FOR 200 – P/N – FCBS200, FOR 250 – FCBS250

NUT STAND FOR BALL SCREWFor 200 P/N : MC2003, For 250 P/N – MC2503

C/F SCREW COVERFOR 200 P/N : MC2001FOR 250 P/N : MC2501

CAP NUTMG2002

THRUST BEARING for C/F #7202P/N: MC2004

NUT STANDFor 200 P/N : MC2002For 250 P/N : MC2502

CROSS FEED SCREW AND BUSHINGSTD FOR 250MH – P/N : CF250FINE FOR 250MH – P/N: FC250

THRUST BEARING 51104 – P/N : MC2504

DIAL & SUB DIAL FOR C/F – FOR 200 P/N : MC2005FOR 250 P/N : MC2505

THUMBSCREWMG2006

Pg. 7

March 2009

Fine Cross Feed Attachment For 200/250MH

FINE CROSS FEED SCREW & BUSHING For 200 P/N: FC200For 250 P/N : FC250

FINE CROSS FEED ATTACHMENT ASSEMBLYFOR 200MH P/N : FCA200FOR 250MH P/N : FCA250

FINE CROSS FEEDDIAL & SUB-DIALFOR 200 P/N : MC2006FOR 250 P/N : MC2506

THUMB SCREWP/N: MG2006

KNOB FOR FINE FEEDP/N : MC2007

FINE CROSS FEED BALL SCREW(Not pictured)For 200MH P/N: FCBS200For 250MH P/N: FCBS250

Pg. 8

March 2009

S/N DESCRIPTION200MH 205MH 250MH

1 Cross Feed Screw & Bushing Std CF2502 Cross Feed Screw & Bushing Fine FC2503 Cross Feed Ball Screw Std CFBS2504 Cross Feed Ball Screw Fine FCBS2505 Fine Cross Feed Attachment FCA2506 Screw Cover for C/F MC25017 Nut Stand Std MC25028 Nut Stand For Ball Screw MC25039 Thrust Bearing for C/F MC250410 Dial & Sub Dial Assly for C/F MC250511 Dial & Sub Dial Assly for Fine C/F MC2506

CROSS FEED PARTS

FCA200

MC2005MC2006

MC2003MC2004

Part Number

MC2001MC2002

CF200FC200

CFBS200FCBS200

Pg. 9

March 2009

V/F Parts for 200/250MHVERTICAL FEED HAND WHEEL

P/N : HWVFDIAL & SUBDIAL FOR V/FP/N: MV2001

VERTICAL FEED SCREW & BUSHING STDFOR200/205 P/N : VF200FOR250 P/N: VF250

Handle Grip OnlyP/N : HGRIP

Thumb Screw P/N : MG2006Pin for Thumb Screw P/N: MG2008V/F SCREW COVER FOR 200/250

(Not shown)P/N : MV2009

BELLOW FOR V/F WAY COVER FOR 200 P/N : MV2011FOR 250 P/N: MV2511

Pg. 10

March 2009

Fine V/F for 200/205/250MH

FINE VERTICAL FEED UNIT FOR200,205,250MHOptional in Place of Std V/F -- P/N - FV200

DIAL & SUB DIAL FOR V/FP/N : MV2006

DIAL FOR FINE FEEDP/N : MV2007

CAP NUTP/N: MG2002

WASHERP/N: MG2003

KNOB FOR FINE FEEDP/N: MV2008

Pg. 11

March 2009

S/N DESCRIPTION200MH 205MH 250MH

1 Vertical Feed Screw & Bushing2 Dial & Sub dial for Vertical Feed3 Hand Wheel for Vertical Feed4 Thumb Screw5 Pin for Thumb Screw6 Vertical Feed Screw Cover7 Pinion and Spiral Gear set8 Pinion Shaft9 Lock Washer for V/F # 82

10 Lock Nut for V/F # 6511 Fine Vertical Feed Unit12 Dial & Sub dial for Fine Vertical13 Dial For fine Feed14 Knob for fine Feed15 Bellow for Vertical Way Cover MV2510

VERTICAL FEED PARTS

MV2006MV2007MV2008

MV2003MV2004MV2005FV200

MV2010

Part Number

HWVF

VF200MV2001

MG2006MG2008MV2009

VPS

Pg. 12

March 2009

Spindle Head for 200/250SPINDLE STANDARD (New) – SP200SPINDLE STANDARD(Rebuilt) – SPRE OR SPRI(Rebuilt on exchange basis)

COUPLING ASSEMBLY STANDARD. – MS2006

SPINDLE MOTORMTR1K2P220

P/N : MS2015

VERTICAL FEED SCREW & BUSHINGFor 200 – VF200For 250 – VF250

SPINDLE BOLTP/N - SPNUT RUBBER SPIDER(OLD)- P/N: MS2007A

(NEW)- P/N: MS2007

Pg. 13

SPINDLE NUTP/N – SPBOLT

March 2009

200MH 205MH 250MH1 Spindle Standard (New)2 Spindle Standard External(Rebuilt)3 Spindle Standard Internal (Rebuilt)4 Spindle Bolt5 Spindle Nut6 Coupling Assembly7 Rubber Spider (New) - 8 Prong8 Rubber Spider (Old) - 2 Pcs set9 Spindle Motor Std-1kw2P220.10 Spindle Motor - 1kw2P46011 Spindle Motor -1.5kw2P22012 Spindle Motor -1.5kw2P46013 Spindle Motor -1.5kw4P22014 Spindle Motor -1.5kw4P460

SP200SPRE

MS2007MS2007AMS2015MS2016

SPRISPBOLTSPNUTMS2006

MS2017MS2018MS2019MS2020

Pg. 14

March 2009

L/F Parts for 200/205/250MHLINEAR BALL BEARINGSFor 200 – P/N : LB200For 205/250 – P/N : LB250

HARDENED STEEL WAYSNew For 200 – P/N – HS200New For205/250 – P/N – HS250Rebuilt For 200 – P/N – HS200RRebuilt For 205/250 – P/N – HS250R

LONGITUDINAL HAND WHEEL For 200/205/250 P/N: HWLG

TABLE LOCK ASSEMBLY200-P/N:2016250-P/N:2516

RUBBER MAT For 200– P/N:MG2004For 250 – P/N: MG2005

CABLEFor 200MH – CABLE200For 205MH – CABLE205For 250MH – CABLE250

Pg. 15

March 2009

S/N DESCRIPTION200MH 205MH 250MH

1 Hardened Steel Ways HS200 HS250 HS2502 Hardened Steel Ways( Rebuilt ) HS200R HS250R HS250R3 Linear Ball Bearing LB200 LB250 LB2504 Cable for Drum CABLE200 CABLE205 CABLE2505 Table Drum Lock Assly ML25166 Hand Wheel for L/F7 Hand Wheel Lock Nut for L/F8 Spring Washer for L/F9 Table Stopper Assly

10 Table End Guard ML2509

LONGITUDINAL FEED PARTS

ML2009ML2001

Part Number

ML2003ML2002

HWLGML2016

Pg. 16

March 2009

Coolant coverSPECIAL WHEEL GUARD

for 8” P/N : SPWG8COOLANT COVERCOMPLETELess Tank

SPLASH GUARD FRONT(Metal)FOR 200 – ML2011FOR 205 – ML2110FOR 250 – ML2510

RUBBER SPLASH GUARDP/N : FOR200 – ML2010

FOR205 – ML2110FOR250 – ML2510

TABLE DUST COVER

200MH 205MH 250MH

Coolant Cover Complete less Tank CC200 CC205 CC250Splash Guard (Rubber) ML2010 ML2110 ML2510

Splash Guard (Metal) ML2011 ML2111 ML2511

Table Dust Cover ( L & R) ML2012 ML2012 ML2512

COOLANT COVER PART NOS

Pg. 17