Models 818, 819, 820...Trusted. ested. ough. ® zoellerpumps.com 800-928-7867 3649 Cane Run Road,...
2
Trusted. Tested. Tough. ® zoellerpumps.com 800-928-7867 3649 Cane Run Road, Louisville, KY 40211 USA Grinder blade and cutting plate • Dual blade, angled cutter design provides superior grinding with sharper cutting edges • More torque delivered to each cutter blade • Lowering amp spikes during demanding grinding cycles • Cutting plate decreases solids to less than 1/8” (3 mm) • Cool-run design incorporates an oil-filled motor with finned housings • Automatic & non-automatic models - 1 HP: 115/200/230 Volt, 1 Phase - 1.5 & 2.0 HP: 200/230 Volt, 1 Phase - 1.0, 1.5 & 2.0 HP: 200/230/460/575 Volt, 3 Phase Zoeller Shark ® Series grinder pumps are engineered to grind and pump tough materials, including disposable wipes, found in today’s wastewater applications. ® 100% factory tested Models 818,819,820 Grinder Series FM2966 0420 Spuersedes 0117
Transcript of Models 818, 819, 820...Trusted. ested. ough. ® zoellerpumps.com 800-928-7867 3649 Cane Run Road,...
Trusted. Tested. Tough.®zoellerpumps.com 800-928-78673649 Cane Run Road, Louisvil le, KY 40211 USA
Grinder blade and cutting plate
• Dual blade, angled cutter design provides superior grinding with sharper cutting edges
• More torque delivered to each cutter blade
• Lowering amp spikes during demanding grinding cycles
• Cutting plate decreases solids to less than 1/8” (3 mm)
• Cool-run design incorporates an oil-filled motor with finned housings
• Automatic & non-automatic models - 1 HP: 115/200/230 Volt, 1 Phase - 1.5 & 2.0 HP: 200/230 Volt, 1 Phase - 1.0, 1.5 & 2.0 HP: 200/230/460/575 Volt, 3 Phase
Zoeller Shark® Series grinder pumps are engineered to grind and pump tough materials, including disposable wipes, found in today’s wastewater applications.
®
100% factory tested
Models
818, 819, 820 Grinder Series
FM29660420
Spuersedes0117
© Copyright 2020 Zoeller® Co. All rights reserved.502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | zoellerpumps.com
All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).CAUTION
SK1621
1-1/4" NPT
18-5/8" [473 mm]
5" [127 mm]
6-1/2"[165 mm]
4" [102 mm]
4" [102 mm]
7-5/8"[194 mm]
4"[102 mm]
*115 Volt model 818 only
Tested to Standard UL778 andCertified to CSA
Standard C22.2 No. 108
154108
20
30
40
50
60
10 15 20 25 30 35 40 45 50 555
20 40 60 80 100 120 140 160 180 200
0
MET
ERS
FEET
PUMP PERFORMANCE CURVEMODELS 818/819/820
0
TOTA
L DY
NA
MIC
HEA
D
FLOW PER MINUTE
U.S. GALLONSLITERS
70
10
80
90
100
110
4
8
12
16
20
24
28
32 820
819
818
PRODUCT SPECIFICATIONS
MO
TO
R
Horse Power 1.0 - 2.0
Voltage 115* / 200 - 575
Phase 1 Ph or 3 Ph
Hertz 60 Hz
RPM 3450
Type Capacitor start / capacitor run or 3 Ph
Insulation Class B
Amps 2.7 - 15.5
PUM
P
Operation Automatic or nonautomatic
Auto On / Off Variable level float switch, customer sets
Discharge Size 1-1/4" NPT vertical discharge
Cord Length 20' (6 m) standard
Cord Type SOOW multi-wire neoprene
Max. Head 107' (32.6 m)
Max. Flow Rate 46 GPM (174 LPM)
Max. Operating Temp. 130 °F (54 °C)
Cooling Oil filled
Motor Protection Auto reset thermal overload (1 Ph)
MA
TER
IALS
Cap Cast iron
Motor Housing Cast iron
Adapter Cast iron
Pump Housing Cast iron
Upper Bearing Ball bearing
Lower Bearing Ball bearing
Mechanical Seals Carbon / ceramic
Impeller Type Vortex
Impeller Engineered plastic
Hardware 304 Stainless steel
Motor Shaft 416 Stainless steel
Gasket & Square Ring Neoprene
Cutter Type 440C stainless steel hardened to Rockwell C55-60
