Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the...
Transcript of Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the...
![Page 1: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/1.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Available for Refrigeration Service
1010 1” NPT1110 3/4” NPT1210 1/2” NPT1010J8 1/2” SAE O-Ring1010J12 3/4” SAE O-Ring1010J16 1” SAE O-Ring
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle of
expanding wax, which in the semi-liquid state undergoes large expansion
rates within a relatively narrow temperature range. The self-contained ele-
ment activates a stainless steel sleeve, which directs flow. All FPE
Thermostatic Valves are factory set at predetermined temperatures: no fur-
ther adjustments are necessary. A wide range of temperatures are avail-
able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-
ed back to the main system. As fluid temperature rises to the control range,
some fluid is diverted to the cooling system. As fluid temperature contin-
ues to increase, more flow is diverted. When the thermostat is in a fully
stroked condition, all fluid flow is directed to the cooling system. FPE
Thermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid enters
the “C” port. The flows mix and the thermostat adjusts to reach the desired
temperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from aluminum and
grey iron castings, however, ductile iron, bronze, steel and stainless steel
housings are available.
Optional 1010 features: High over temperature element, plated element.
Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-WayThermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 1010
![Page 2: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/2.jpg)
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 1010
PRESSURE RATINGSMATERIAL PSI
A, AL, B 150D 250
S, SS 500
For port sizes not shown consult factory
* (Replace * with body material type; A=Cast Iron, AL=Aluminum, B=Bronze, D=Ductile Iron, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult yourfactory representative.
FPE1010-050803
All models
Viton® is a registered trademark of Dupont Dow Elastomers
PART # DESCRIPTION*1010 VALVE BODY (*See table for material)*1020 VALVE COVER (*See table for material)1080 GASKET (Older than 1979)1572** O-RING (Standard material is Buna-N)1071 LIP SEAL1060-Temp THERMOSTAT (Temp to follow dash)1600 HEX BOLT1601 LOCK WASHER1590 NAMEPLATE
FPE Model 1000* Replacement Kit (Includes the following:)1572** O-RING (Standard material is Buna-N)1071 LIP SEAL1060-Temp THERMOSTAT (Temp to follow dash)(For Viton® (V) or Neoprene (E) O-Ring material, replace ** with V or E)
Flow vs. Pressure Drop
FLOWIN U.S. GPMSAE 10 @ 100° F
1/2” 3/4” 1”
Recommended Pressure Drop is 2 to 7 PSI
![Page 3: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/3.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Compact
Available for Refrigeration Service
1011 1” NPT1111 3/4” NPT1211 1/2” NPT1411 1 1/4” NPT1511 1 1/2” NPT
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle of
expanding wax, which in the semi-liquid state undergoes large expansion
rates within a relatively narrow temperature range. The self-contained ele-
ment activates a brass or nickel plated sleeve, which directs flow. All FPE
Thermostatic Valves are factory set at predetermined temperatures: no fur-
ther adjustments are necessary. A wide range of temperatures are avail-
able for city or treated water temperature control applications.
On start-up, a majority of the fluid flow is blocked by a sleeve. A small
amount will flow through the weep hole to the drain. As fluid temperature
rises to the control range, more of the fluid is directed to the drain, and
when the thermostat is in a fully stroked condition, all fluid flow is directed
to the drain. This FPE valve is designed for use in water saver applica-
tions.
Standard FPE Thermostatic Valve Housings are made from aluminum and
grey iron castings; however, ductile iron, bronze, steel and stainless steel
housings are available.
Optional 1011 features: High over temperature element, plated element.
Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Two-Way (Water Saver)Thermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 1011
![Page 4: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/4.jpg)
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 1011
Flow vs. Pressure Drop
FLOW IN U.S. GPMSAE 10 @ 100° F
PART # DESCRIPTION*1011 VALVE BODY (*See table for material)*1040 VALVE COVER (*See table for material)1572** O-RING (Standard material is Buna-N)1571 LIP SEAL1560-Temp THERMOSTAT (Temp to follow dash)1600 HEX BOLT1601 LOCK WASHER1590 NAMEPLATE
FPE Model 1500** Replacement Kit (Includes the following:)1572** O-RING (Standard material is Buna-N)1571 LIP SEAL1560-Temp THERMOSTAT (Temp to follow dash)(For Viton® (V) or Neoprene (E) O-Ring material, replace ** with V or E)
PRESSURE RATINGSMATERIAL PSI
A, AL, B 150D 250
S, SS 500
For port sizes not shown consult factory
* (Replace * with body material type; A=Cast Iron, AL=Aluminum, B=Bronze, D=Ductile Iron, S=Steel, SS=Stainless Steel)
1/2” 3/4”
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE1011-050803
1”
All models
1 1/4”
1 1/2”
Viton® is a registered trademark of Dupont Dow Elastomers
Recommended Pressure Drop is 2 to 7 PSI
![Page 5: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/5.jpg)
Features
Wide Range ofTemperatures
Mountable Housing
Heavy Duty
Self-Contained
Replaceable Element WithoutBreaking Connections
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate In Any Position
Compact
Three-Way0750 3/4" NPT0750D1 3/4" NPT Low Flow0750J12 3/4" SAE O-Ring0750J12D1 3/4" SAE O-Ring Low Flow0752 1/2" NPT0752D1 1/2” NPT Low Flow
Two-Way (Water Saver)0750JW 3/4” NPT0750JWJ12 3/4" SAE O-Ring0752JW 1/2" NPT
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system in the three-way valve or blocked by a sleevein the two-way version. As fluid temperature rises to the control range,some fluid is diverted to the cooling system in the three-way valve or todrain in the two-way version. As fluid temperature continues to increase,more flow is diverted. When the thermostat is in a fully stroked condition,all fluid flow is directed to the cooling system in the three-way valve or todrain in the two-way version. FPE Thermostatic Valves may also be usedin a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
FPE Thermostatic Valve Housings are made from cast aluminum or castbronze, with other materials available.
Optional 0750 features: Plated elements and Viton® or Neoprene seals.Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way or Two-Way (Water Saver) Thermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 0750
![Page 6: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/6.jpg)
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 0750
Flow vs. Pressure Drop
FLOW IN U.S. GPMSAE 10 @ 100° F
PART # DESCRIPTION*0750-1 VALVE BODY (*See table for material)0750-3 CAP0750-4 SPRING0750**-6 O-RING (Standard material is Buna-N)0750-7 SNAP RING0750-9 SLEEVE (Specify weep hole or low flow)0760-Temp THERMOSTAT (Temp to follow dash)0750-10 PLUG (2-way valve only)
FPE Model 0700* Replacement Kit (Includes the following:)0750-4 SPRING0750**-6 O-RING (Standard material is Buna-N)0760-Temp THERMOSTAT (Temp to follow dash)(For Viton® (V) or Neoprene (E) O-Ring material, replace ** with V or E)
PRESSURE RATINGSMATERIAL PSI
AL, B 150
Three-Way Valve Two-Way Valve
For port sizes not shown consult factory
* (Replace * with body material type; AL=Aluminum, B=Bronze)
1/2 3/4
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE-0750-050803
Viton® is a registered trademark of Dupont Dow Elastomers
Low Flow
Note: Two-way water-saver valves musthave weep hole
Recommended Pressure Drop is 2 to 7 PSI
![Page 7: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/7.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Compact
Available for Refrigeration Service
1530 1 1/2” NPT1530M 1 1/2” NPT with Manual Override1530J16 1” SAE O-Ring1530J20 1 1/4” SAE O-Ring1530J24 1 1/2” SAE O-RingF1530 1 1/2” 125# FF FlangeSF1530 1 1/2” 150# RF FlangeSF1530X 1 1/2” 300# RF Flange
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle of expand-ing wax, which in the semi-liquid state undergoes large expansion rates with-in a relatively narrow temperature range. The self-contained element activatesa brass or nickel-plated sleeve, which directs flow. All FPE ThermostaticValves are factory set at predetermined temperatures: no further adjustmentsare necessary. A wide range of temperatures are available for water and oiltemperature control applications.
When used in a diverting application, on start-up the total fluid flow is routedback to the main system. As fluid temperature rises to the control range, somefluid is diverted to the cooling system. As fluid temperature continues toincrease, more flow is diverted. When the thermostat is in a fully stroked con-dition, all fluid flow is directed to the cooling system. FPE Thermostatic Valvesmay also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid enters the“C” port. The flows mix and the thermostat adjusts to reach the desired tem-perature, exiting the “A” port.
Standard FPE Thermostatic Valve Housings are made from aluminum andgrey iron castings, however, ductile iron, steel and stainless steel housings areavailable.
Available connections: NPT, SAE O-Ring, 125# FF Flange, 150# RF Flange,300# RF Flange, Navy and Metric Flanges.
Optional Features: Manual Override, High Over Temp elements, Plated ele-ments. Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 1530
![Page 8: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/8.jpg)
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 1530
Flow vs. Pressure Drop
FLOW IN U.S. GPMSAE 10 @ 100° F
PART # DESCRIPTION*1530 VALVE BODY (*See table for material)*1540 VALVE COVER (*See table for material)1572** O-RING (Standard material is Buna-N)1571 LIP SEAL1560-Temp THERMOSTAT (Temp to follow dash)1600 HEX BOLT1601 LOCK WASHER1590 NAMEPLATE
FPE Model 1500** Replacement Kit (Includes the following:)1572** O-RING (Standard material is Buna-N)1571 LIP SEAL1560-Temp THERMOSTAT (Temp to follow dash)(For Viton® (V) or Neoprene (E) O-Ring material, replace ** with V or E)
PRESSURE RATINGSMATERIAL PSI
A, B 150D 250
S, SS 500SF, SSF 275
SFX, SSFX 720
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile Iron, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE1530-050803
*1530, *1530J *F1530, *F1530X *1530M *F1530M, *F1530XM
Viton® is a registered trademark of Dupont Dow Elastomers
Recommended Pressure Drop is 2 to 7 PSI
![Page 9: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/9.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Compact
Available for Refrigeration Service
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 2010
2010 2” NPT2010-1 1 1/2” NPT2010J24 1 1/2” SAE O-RingA2010J32 2” SAE O-RingF2010 2” 125# FF FlangeSF2010 2” 150# RF FlangeSF2010X 2” 300# RF Flange
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system. As fluid temperature rises to the controlrange, some fluid is diverted to the cooling system. As fluid temperaturecontinues to increase, more flow is diverted. When the thermostat is in afully stroked condition, all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from aluminum andgrey iron castings, however, ductile iron, bronze, steel and stainless steelhousings are available.
Available Connections: NPT, SAE O-Ring, 125# FF Flange, 150# and300# RF Flange.
Optional features: High over temperature element, plated element. Otheroptions available upon request.
![Page 10: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/10.jpg)
PRESSURE RATINGSMATERIAL PSI
A, B 150D 250
S, SS 500SF, SSF 275
SFX, SSFX 720
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 2010
*2010-1, *2010, *2010J
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult yourfactory representative.
FPE-2010-050803
*F2010, *F2010X
Flow vs. Pressure Drop
FLOW IN U.S. GPMSAE 10 @ 100° F
1 1/2”
2”
PART # DESCRIPTION*2010 VALVE BODY (*See table for material)*2020 VALVE COVER (*See table for material)1570** O-RING (Standard material is Buna-N)2071 LIP SEAL2050-Temp THERMOSTAT (Temp to follow dash)1600 HEX BOLT1601 LOCK WASHER
FPE Model 2000** Replacement Kit (Includes the following:)1570** BUNA O-RING (Standard material is Buna-N)2071 LIP SEAL2050-Temp THERMOSTAT (Temp to follow dash)(For Viton® (V) or Neoprene (E) O-Ring material, replace ** with V or E)
Viton® is a registered trademark of Dupont Dow ElastomersRecommended Pressure Drop is 2 to 7 PSI
![Page 11: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/11.jpg)
Features
Designed for Hydraulic Power Units
Optional Mounting Rails
Wide Range of Temperatures
Self-Contained
Replaceable Element
Non Adjustable
Rugged Construction
Tamper-Proof
Compact Operate in Any Position
Extra Heavy Casting
2012-1 1 1/2” NPT2012 2” NPT2012J24 1 1/2” SAE O-ring2012J32 2” SAE O-ring2012M 2” NPT with Manual OverrideF2012 2” FlangeF2012M 2” Flange with Manual Override
With Bulkhead Mounting Provisions2013-1 1 1/2” NPT2013 2” NPT2013J24 1 1/2” SAE O-ring2013J32 2” SAE O-ring2013M 2” NPT with Manual Override
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system. As fluid temperature rises to the controlrange, some fluid is diverted to the cooling system. As fluid temperaturecontinues to increase, more flow is diverted. When the thermostat is in afully stroked condition, all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from aluminum andgrey iron castings, however, ductile iron, bronze, steel and stainless steelhousings are available.
Optional features: High over temperature element, plated element, manu-al override.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve (T Style)
MADE IN
U. S. A.ISO 9001-2000
Model 2012 & 2013
![Page 12: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/12.jpg)
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 2012 & 2013
PART # DESCRIPTION*2012 VALVE BODY (*See table for material)*2013 VALVE BODY W/MOUNTING HOLES*2020 VALVE COVER (*See table for material)2071 LIP SEAL2050-Temp THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1570** O-RING (Standard material is Buna-N)1590 NAMEPLATE
FPE Model 2000** Replacement Kit (Includes the following:)1570** O-RING (Standard material is Buna-N)2071 LIP SEAL2050-Temp THERMOSTAT (Temp to follow dash)(For Viton® (V) or Neoprene (E) O-Ring material, replace ** with V or E)
*2012, *2012J
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE-2012-050803
*2012M *F2012 *F2012M *2013, *2013J
Viton® is a registered trademark of Dupont Dow Elastomers
PRESSURE RATINGSMATERIAL PSI
A, B 150D 250
S, SS 500SF, SSF 275
SFX, SSFX 720
2013 Mounting Holes
Flow vs. Pressure Drop
FLOW IN U.S. GPMSAE 10 @ 100° F
Recommended Pressure Drop is 2 to 7 PSI
![Page 13: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/13.jpg)
Features
Designed for Refrigeration Service
Neoprene O-ring SealOn Cover
Wide Range of Temperatures
Self-Contained
Replaceable Element withoutBreaking Connections
Non-Adjustable
Rugged Construction
Tamper-Proof
Compact Operate In Any Position
S2014-1 1 1/2” Socket Weld ConnectionS2014 2” Socket Weld ConnectionS2015-1 1 1/2” Socket Weld Connection
(Reverse Flow)S2015 2” Socket Weld Connection
(Reverse Flow)S2014-X16 2” Butt Weld ConnectionS2015-X16 2” Butt Weld Connection
(Reverse Flow)
Fluid Power Energy (FPE) Thermostatic Valves utilize the prin-ciple of expanding wax, which in the semi-liquid state under-goes large expansion rates within a relatively narrow temper-ature range. The self-contained nickel-plated element assem-bly activates a sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temper-atures: no further adjustments are necessary. A wide range oftemperatures are available for water and oil temperature con-trol applications.
When used in a diverting application, on start-up the total fluidflow is routed back to the main system. As fluid temperaturerises to the control range, some fluid is diverted to the coolingsystem. As fluid temperature continues to increase, more flowis diverted. When the thermostat is in a fully stroked condition,all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colderfluid enters the “C” port. The flows mix and the thermostatadjusts to reach the desired temperature, exiting the “A” port.
FPE 2014/2015 Thermostatic Valve Housings are made from(WCB) steel.
Optional features available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve (Refrigeration)
MADE IN
U. S. A.ISO 9001-2000
Model 2014 & 2015
![Page 14: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/14.jpg)
PRESSURE RATINGSMATERIAL PSI
S 500
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 2014 & 2015
Flow vs. Pressure Drop
FLOW IN U.S. GPMSAE 10 @ 100° F
2014-1, 2014
FPE-2014-050803
PART # DESCRIPTIONS2104 VALVE BODYS2024 VALVE COVER2014-2 SPRING2071 LIP SEAL2040P-Temp PLATED THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1570E NEOPRENE O-RING1590 NAMEPLATE
FPE Model 2000E Replacement Kit (Includes the following:)1570E NEOPRENE O-RING2071 LIP SEAL2050P-Temp PLATED THERMOSTAT (Temp to follow dash)
2015-1, 2015 Profile View
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
*(Replace * with body material type; S=Steel)
Recommended Pressure Drop is 2 to 7 PSI
2”
![Page 15: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/15.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Compact
Available for Refrigeration Service
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve (T Style)
MADE IN
U. S. A.ISO 9001-2000
Model 2510
2510 2 1/2” Flange2510M 2 1/2” Flange with Manual Override
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system. As fluid temperature rises to the controlrange, some fluid is diverted to the cooling system. As fluid temperaturecontinues to increase, more flow is diverted. When the thermostat is in afully stroked condition, all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from aluminum andgrey iron castings, however, ductile iron, bronze, steel and stainless steelhousings are available.
Available Connections: 125# FF Flange, 150# RF Flange, 300# RFFlange, Navy and Metric Flanges.
Optional features: Manual Override, High Over Temp element, Plated ele-ment. Other options available upon request.
![Page 16: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/16.jpg)
Flow vs. Pressure Drop
PRESSURE RATINGSMATERIAL PSI
A, B, D 125S, SS 275
SX, SSX 720
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 2510
FLOW IN U.S. GPMSAE 30 @ 140° F
PART # DESCRIPTION*2510 VALVE BODY (*See table for material)*2520 VALVE COVER (*See table for material)2071 LIP SEAL3080-C GASKET2050-Temp THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1590 NAMEPLATE
FPE Model 2500 Replacement Kit (Includes the following:)3080-C GASKET(2) 2071 LIP SEAL(2) 2050-Temp THERMOSTAT (Temp to folllow dash)
*2510, *2510X
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE-2510-050803
*2510M, *2510XM
Recommended Pressure Drop is 2 to 7 PSI
![Page 17: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/17.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Compact
Available for Refrigeration Service
3010 3” Flange3010M 3” Flange with Manual Override
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system. As fluid temperature rises to the controlrange, some fluid is diverted to the cooling system. As fluid temperaturecontinues to increase, more flow is diverted. When the thermostat is in afully stroked condition, all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from aluminum andgrey iron castings, however, ductile iron, bronze, steel and stainless steelhousings are available.
Available Connections: 125# FF Flange, 150# RF Flange, 300# RFFlange, Navy and Metric Flanges.
Optional features: Manual Override, High Over Temp element, Plated ele-ment. Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve (T Style)
MADE IN
U. S. A.ISO 9001-2000
Model 3010
![Page 18: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/18.jpg)
Flow vs. Pressure Drop
PRESSURE RATINGSMATERIAL PSI
A, B, D 125S, SS 275
SX, SSX 720
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 3010
FLOWIN U.S. GPMSAE 30 @ 140° F
PART # DESCRIPTION*3010 VALVE BODY (*See table for material)*3020 VALVE COVER (*See table for material)2071 LIP SEAL3080-C GASKET2050-Temp THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1590 NAMEPLATE
FPE Model 3000 Replacement Kit (Includes the following:)3080-C GASKET(2) 2071 LIP SEAL(2) 2050-Temp THERMOSTAT (Temp to follow dash)
*3010, *3010X
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housingmaterial. For Model coding information,
visit our website or consult your factory representative.
FPE-3010-050803
*3010M, *3010XM
Recommended Pressure Drop is 2 to 7 PSI
![Page 19: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/19.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Available for Refrigeration Service
4010 4” Flange4010M 4” Flange with Manual Override
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system. As fluid temperature rises to the controlrange, some fluid is diverted to the cooling system. As fluid temperaturecontinues to increase, more flow is diverted. When the thermostat is in afully stroked condition, all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from aluminum andgrey iron castings, however, ductile iron, bronze, steel and stainless steelhousings are available.
Available Connections: 125# FF Flange, 150# RF Flange, 300# RFFlange, and Navy Flanges.
Optional features: Manual Override, High Over Temp element, Plated ele-ment. Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 4010
![Page 20: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/20.jpg)
Flow vs. Pressure Drop
PRESSURE RATINGSMATERIAL PSI
A 150B 125D 200
S, SS 275SX, SSX 720
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 4010
FLOW IN U.S. GPMSAE 30 @ 140° F
PART # DESCRIPTION*4010 VALVE BODY (*See table for material)*4020 VALVE COVER (*See table for material)2071 LIP SEAL4080-C GASKET2050-Temp THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1590 NAMEPLATE
FPE Model 4000 Replacement Kit (Includes the following:)4080-C GASKET(4) 2071 LIP SEAL(4) 2050-Temp THERMOSTAT (Temp to follow dash)
*4010, *4010X
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE-4010-050803
*4010M, *4010XM
Recommended Pressure Drop is 2 to 7 PSI
![Page 21: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/21.jpg)
Features
Wide Range of Temperatures
Heavy Duty
Self-Contained
Replaceable Element
Non-Adjustable
Rugged Construction
Tamper-Proof
Operate in Any Position
Compact
Available for Refrigeration Service
5010 5” Flange5010M 5” Flange with Manual Override
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle ofexpanding wax, which in the semi-liquid state undergoes large expansionrates within a relatively narrow temperature range. The self-contained ele-ment activates a stainless steel sleeve, which directs flow. All FPEThermostatic Valves are factory set at predetermined temperatures: no fur-ther adjustments are necessary. A wide range of temperatures are avail-able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-ed back to the main system. As fluid temperature rises to the controlrange, some fluid is diverted to the cooling system. As fluid temperaturecontinues to increase, more flow is diverted. When the thermostat is in afully stroked condition, all fluid flow is directed to the cooling system. FPEThermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid entersthe “C” port. The flows mix and the thermostat adjusts to reach the desiredtemperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from grey iron cast-ings, however, ductile iron, bronze, steel and stainless steel housings areavailable.
Available Connections: 125# FF Flange, 150# RF Flange, 300# RFFlange, and Navy Flanges.
Optional features: Manual Override, High Over Temp element, Plated ele-ment. Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-Way Thermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 5010
![Page 22: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/22.jpg)
PRESSURE RATINGSMATERIAL PSI
A, B, D 125S, SS 275
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 5010
FLOW IN U.S. GPMSAE 30 @ 140° F
PART # DESCRIPTION*5010 VALVE BODY (*See table for material)*5020 VALVE COVER (*See table for material)2071 LIP SEAL5080-C GASKET2050-Temp THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1590 NAMEPLATE
FPE Model 5000 Replacement Kit (Includes the following:)5080-C GASKET(6) 2071 LIP SEAL(6) 2050-Temp THERMOSTAT (Temp to follow dash)
*5010, *5010X
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE-5010-050803
*5010M, *5010XM
Flow vs. Pressure Drop
Recommended Pressure Drop is 2 to 7 PSI
![Page 23: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/23.jpg)
Features
Self-Contained
Non-Adjustable
Tamper-Proof
Compact
Wide Range of Temperatures
Heavy Duty
Replaceable Element
Rugged Construction
Operate in Any Position
6010 6” Flange6010M 6” Flange with Manual Override
Fluid Power Energy (FPE) Thermostatic Valves utilize the principle of
expanding wax, which in the semi-liquid state undergoes large expansion
rates within a relatively narrow temperature range. The self-contained ele-
ment activates a stainless steel sleeve which directs flow. All FPE
Thermostatic Valves are factory set at predetermined temperatures: no fur-
ther adjustments are necessary. A wide range of temperatures are avail-
able for water and oil temperature control applications.
When used in a diverting application, on start-up the total fluid flow is rout-
ed back to the main system. As fluid temperature rises to the control range,
some fluid is diverted to the cooling system. As fluid temperature contin-
ues to increase, more flow is diverted. When the thermostat is in a fully
stroked condition, all fluid flow is directed to the cooling system. FPE
Thermostatic Valves may also be used in a mixing application.
In a mixing application, hot fluid enters the “B” port and colder fluid enters
the “C” port. The flows mix and the thermostat adjusts to reach the desired
temperature, exiting the “A” port.
Standard FPE thermostatic valve housings are made from grey iron cast-
ings, however, ductile iron, bronze, steel and stainless steel housings are
available.
Available connections: 125# FF Flange, 150# RF Flange, 300# RF Flange,
Navy and Metric Flanges.
Optional Features: Manual Override, High Over Temp element, Plated ele-
ment. Other options available upon request.
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Three-WayThermostatic Valve
MADE IN
U. S. A.ISO 9001-2000
Model 6010
![Page 24: Model 101 0 - Fluid · PDF fileFluid Power Energy (FPE) Thermostatic Valves utilize the principle of expanding wax, which in the semi-liquid state undergoes large expansion](https://reader035.fdocuments.in/reader035/viewer/2022062401/5a93a4907f8b9aba4a8baa4e/html5/thumbnails/24.jpg)
FLUID POWER ENERGY, INC.W229 N591 Foster Court • Waukesha, WI 53186
262 •548 •6220 Fax 262 •548 • 6239www.fpevalves.com
Model 6010
Flow vs. Pressure Drop
FLOWIN U.S. GPMSAE 30 @ 140° F
PART # DESCRIPTION*6010 VALVE BODY (*See table for material)*6020 VALVE COVER (*See table for material)2071 LIP SEAL6080-C GASKET2050-Temp THERMOSTAT (Temp to follow dash)1604 HEX BOLT1605 LOCK WASHER1590 NAMEPLATE
FPE Model 6000 Replacement Kit (Includes the following:)6080-C GASKET(9) 2071 LIP SEAL(9) 2050-Temp THERMOSTAT
PRESSURE RATINGSMATERIAL PSI
A, B, D 125S, SS 275
For port sizes not shown consult factory
* (Replace * with body material type; A=Cast Iron, B=Bronze, D=Ductile Iron, S=Steel, SS=Stainless Steel)
To OrderSpecify Model Number, nominal
temperature desired, and housing material. For Model coding information,
visit our website or consult your factory representative.
FPE-6010-050803
*6010 *6010M
Recommended Pressure Drop is 2 to 7 PSI