Moccasin en Shoemaster
description
Transcript of Moccasin en Shoemaster
-
For Release QS 1.0x
Page N 1 / 22 24/08/07 Mocassin
Create a 3D Mocassin
How to create a Mocassin in 3D using the specific Macro for QS
A- Install the Program
Double click on the 'Mocassin V1.2.exe' file
Select 'English' then Click 'NEXT'
Here you have to input the hard disk reference where to
install files
Click 'NEXT'
-
For Release QS 1.0x
Page N 2 / 22 24/08/07 Mocassin
Basicly the hard disk must be the hard disk where you have installed
Shoemaster program
For example if you have installed Shoemaster on hard disk C:\,
you must specify C:\
For example if you have installed Shoemaster on hard disk D:\,
you must specify D:\
Select New Install then click 'Install'
Select 'Finish'
And add in your 3D Startup File the syntax
$n//mocassin/setup.ini
-
For Release QS 1.0x
Page N 3 / 22 24/08/07 Mocassin
B- Create the Mocassin Model
Please note that the macro
Has been checked with a Right Last
-
For Release QS 1.0x
Page N 4 / 22 24/08/07 Mocassin
A- Create the inner reference line
B- Create the outer reference line
C- Create the bottom reference line
Using the bottom surface
-
For Release QS 1.0x
Page N 5 / 22 24/08/07 Mocassin
D- Create the Apron Pivoted Piece
-
For Release QS 1.0x
Page N 6 / 22 24/08/07 Mocassin
C- Use the Mocassin Macro
Go to the menu Mocassin and select the option Open
You will get the following toolbar
-
For Release QS 1.0x
Page N 7 / 22 24/08/07 Mocassin
;
Step 1- Set the mocassin
Select the Icon Setup Mocassin and follow the instructions below
Select the Outer Upper Reference
-
For Release QS 1.0x
Page N 8 / 22 24/08/07 Mocassin
Select the Inner Upper Reference
-
For Release QS 1.0x
Page N 9 / 22 24/08/07 Mocassin
Select the sprung piece
-
For Release QS 1.0x
Page N 10 / 22 24/08/07 Mocassin
Step 2- Move the Inner Part
Select the Icon Move Inner
-
For Release QS 1.0x
Page N 11 / 22 24/08/07 Mocassin
Step 3- Rotate the Inner Part
Select the Icon Rotate Inner
-
For Release QS 1.0x
Page N 12 / 22 24/08/07 Mocassin
Step 4: Move the Outer Part
Select the Icon Move Outer
-
For Release QS 1.0x
Page N 13 / 22 24/08/07 Mocassin
Step 5- Rotate the Outer Part
Select the Icon Rotate Outer
-
For Release QS 1.0x
Page N 14 / 22 24/08/07 Mocassin
Step 6- Split Mocassin
Select the Icon Split Mocassin
And Follow the order selection below
-
For Release QS 1.0x
Page N 15 / 22 24/08/07 Mocassin
-
For Release QS 1.0x
Page N 16 / 22 24/08/07 Mocassin
-
For Release QS 1.0x
Page N 17 / 22 24/08/07 Mocassin
Step 7- Reverse Line
Select the Icon Reverse Line
The Line Direction must be like the first image below, if not select all line to reverse
-
For Release QS 1.0x
Page N 18 / 22 24/08/07 Mocassin
Step 8- Blend the Inner Part
Select the Icon Blend Inner
Select the following sequence
-
For Release QS 1.0x
Page N 19 / 22 24/08/07 Mocassin
-
For Release QS 1.0x
Page N 20 / 22 24/08/07 Mocassin
Step 9- Blend the Outer Part
Select the Icon Blend Outer
Select the following sequence
-
For Release QS 1.0x
Page N 21 / 22 24/08/07 Mocassin
-
For Release QS 1.0x
Page N 22 / 22 24/08/07 Mocassin
Step 10- Finish Mocassin
Select the Icon Finish Mocassin
This command merges the mocassin line, you are ready to delete nodes on the line