MINIMUM PERMIT REQUIREMENTS

FOR FENCES

THE FOLLOWING DOCUMENTS MUST BE SUBMITTED IN DUPLICATE

PERMIT APPLICATION COMPLETELY FILLED OUT SIGNED AND NOTARIZED FIRE DEPARTMENT PERMIT COMMERCIAL PROPERTIES ZONING APPROVAL DOCUMENTED PROOF OF COST INCLUDING ALL TRADES NOTICE OF COMMENCEMENT OVER $ 2,500.00 IN VALUE HOMEOWNERS APPROVAL IF REQUIRED SURVEY SHOWING ALL EASEMENTS PLAN SHOWING LOCATION OF FENCE. SELECT TYPE OF FENCE NOTICE OF ACCEPTANCE FOR ALL FENCES EXCEPT WOOD OR CHAIN LINK POOL BARRIER REQUIREMENTS COMPLY FLORIDA BUILDING CODE RESIDENTIAL R4101.17, FLORIDA BUILDING CODE BUILDING 424.2.17 THE FENCE SHALL BE ON THE PROPETY WHERE THE POOL IS LOCATED TO COMPLY WITH THE REQUIREMENTS OF THE BUILDING CODE EASEMENT AGREEMENTS SIGNED BY FIVE (5) UTILITIES THE PERMIT APPLICATION WILL NOT BE ACCEPTED WITHOUT THE ABOVE MINIMUM DOCUMENTATION OTHER DOCUMENTS MAY BE REQUIRED DEPENDING UPON THE JOB CONDITIONS

OWNER’S AFFIDAVIT: I certify that all information provided is accurate, and that all work will be performed in compliance with all applicable laws regulating construction and zoning. No work has been commenced prior to the permit sought by this application, and all work will be done as indicated in the application and all accompanying document and plans. NOTICE: In addition, the requirements of this permit, there may be additional restrictions applicable to this property that may be found in the public records of the county, and there may be additional permits required from other governmental entities such as water management districts, County, State or Federal agencies. DISCLAIMER: Issuance of a development permit by a municipality does not in any way create any right on the part of the applicant to obtain a permit from a state or federal agency and does not create any liability on the part of the municipality for issuance of the permit if the applicant fails to obtain requisite approvals or fulfill the obligations imposed by a state or federal agency or undertakes actions that result in a violation of state or federal law. CONDITION: All applicable state and federal permits must be obtained before commencement of the development. CONTRACTOR ______________________________ PRINT NAME OF CONTRACTR ________________________________ SINATURE OF CONTRACTOR STATE OF FLORIDA COUNTY OF BROWARD Sworn to (or affirmed) and subscribed before me this______ day of __________________ 20____, by___________________________ NOTARY:____________________________ SEAL: Personally Known:___________ Or produced Identification______________ Type of Identification Produced__________

OWNER _______________________________ PRINT NAME OF OWNER ________________________________ SIGNATURE OF OWNER STATE OF FLORIDA COUNTY OF BROWARD Sworn to (or affirmed) and subscribed before me this______ day of __________________ 20____, by___________________________ NOTARY:____________________________ SEAL: Personally Known:___________ Or produced Identification______________ Type of Identification Produced__________

PERMIT AFFIDAVIT

FOR ACKNOWLEDGEMENT OF COMPLIANCE WITH RESTRICTIVE DEEDS AND COVENANTS STATE OF FLORIDA: BROWARD COUNTY:

On this day personally appeared before me, the undersigned officer duly authorized to administer oaths and take acknowledgments ____________________________________, who being by me first duly

(HOMEOWNER) sworn, deposes and says:

a/k/a__________________________________________________________ (Street address)

1. That I am the legal owner of the property2. I acknowledge that approval may be required from the following

_______________________________________________________________________________ (Homeowners Association)

Which entities or associations regulate or otherwise govern the community, neighborhood, or development my property is located.

3. I further acknowledge that I am responsible for any additional cost that may be assessed by theTown of Lauderdale by the Sea and/or the entity regulating or governing the subject property as aresult of my not having obtained the necessary approvals from any entity or association that mayregulate or otherwise govern the community neighborhood, development in which my property islocated.

FURTHER AFFIANT SAYETH NAUGHT

Date________________________

__________________________________________________ Owners signature __________________________________________________ Owners printed name

STATE OF FLORIDA COUNTY OF BROWARD

Affirmed and signed before me, on ________________________________the foregoing document was acknowledged before me affiant, ____________________________________, who personally appeared before me at the time of notarization, who signed and acknowledged signing the foregoing document, who did take an oath, and:

Who is personally known to me________ or Who produced the following identification_____________________________

_________________________________________Commission Expiration date: Notary Public

____________________________________________ (Seal) (Printed or typed name)

By my signature below, I acknowledge that the legal description for the property for which I am applying for a permit is _______________________________________________________________

LOT BLOCK SUBDIVISION

Time Limits for Construction - NOTICE TO OWNER

Section 6-12 of the Town’s Code of Ordinances requires:

1. The construction of any new structure or new addition to an existing structure to be completed and all construction material, equipment and debris removed from the property within 18 months of the date of the issuance of the first building permit.

2. The exterior elements of any repair or renovation to an existing structure which requires a building permit shall be completed and all construction material, equipment and debris removed from the property within six months of the issuance of the first building permit.

This notification is the minimum 60 day’s notice required in section 6-12.9(g).

The Failure to complete the construction at

____________________________________________________________________________, by the construction deadline may result in a fine or legal action by the Town.

If there are extenuating circumstances that prohibit the property owner from completing the construction within the deadline, the owner may seek an extension of time from the Town Commission. An application for extension of time may be obtained from the Development Services Department or Town Clerk.

Owner’s Acknowledgement

I acknowledge receipt and understanding of the Town’s code provisions regarding the time period to complete a construction projects.

Signature: _____________________________________ Date: __________________

Print Name: ____________________________________________

Address of Property: _________________________________________

BUILDING DEPARTMENT

DURING A HURRICANE WATCH & BEFORE THE ONSET OF HURRICANE VELOCITY WINDS YOU ARE REQUIRED TO

SECURE THIS SITE IN ACCORDANCE WITH THE BROWARD COUNTY ADMINISTRATIVE PROVISIONS OF THE FLORIDA BUILDING CODE SECTION 110.13

All loose objects in exposed outdoor locations shall be lashed to rigid construction or shall be stored inside an enclosed structure.

Florida Building Code Broward County Administrative Provisions Section 110.13.2.4

NOTICES ISSUED BY THE NATIONAL WEATHER SERVICE OF A HURRICANE WATCH ARE DEEMED SUFFICIENT NOTICE TO THE OWNER OF REAL PROPERTY UPON WHICH CONSTRUCTION IS OCCURRING, OR ANY CONTRACTOR RESPONSIBLE FOR SAID CONSTRUCTION, TO SECURE LOOSE CONSTRUCTION DEBRIS AND LOOSE CONSTRUCTION MATERIALS AGAINST EFFECTS OF HURRICANE FORCE WINDS

This includes but not limited to: • 110.13.2.1 Road Right-of-Way shall remain clear of construction waste and trash• 110.13.2.2 Waste and Trash Enclosures Temporary Toilets• 110.13.2.3 Loose Construction Debris Forms and Construction Materials• 110.13.2.5 Roofing Tile and Materials Construction Shacks• 110.13.2.5 (1) Loading of Roof Tile• 110.13.2.5 (4) Store the construction materials inside an enclosed structure.• 110.13.3 Building materials shall be loaded on a roof no earlier than (20) working days

prior to permanent installation.• Temporary Electric Service Poles

AND PROTECT ALL GLASS AREAS

AFTER RECORDING – RETURN TO:

PERMIT NUMBER:

NOTICE OF COMMENCEMENT The undersigned hereby given notice that improvement will be made to certain real property, and in accordance with Chapter 713, Florida Statues the following information is provided in the Notice of Commencement. 1. DESCRIPTION OF PROPERTY (Legal description & street address, if available) TAX FOLIO NO.:

SUBDIVISION BLOCK TRACT LOT BLDG UNIT

2. GENERAL DESCRIPTION OF IMPROVEMENT:

3. OWNER INFORMATION: a. Name

b. Address c. Interest in property

d. Name and address of fee simple titleholder (if other than Owner) 4. CONTRACTOR’S NAME, ADDRESS AND PHONE NUMBER:

5. SURETY’S NAME, ADDRESS AND PHONE NUMBER AND BOND AMOUNT:

6. LENDER’S NAME, ADDRESS AND PHONE NUMBER:

7. Persons within the State of Florida designated by Owner upon whom notices or other documents may be served as provided by Section 713.13 (1) (a) 7., Florida Statutes: NAME, ADDRESS AND PHONE NUMBER:

8. In addition to himself or herself, Owner designates the following to receive a copy of the Lienor’s Notice as provided in Section 713.13 (1) (b), Florida Statutes: NAME, ADDRESS AND PHONE NUMBER:

9. Expiration date of notice of commencement (the expiration date is 1 year from the date of recording unless a different date is specified): , 20

WARNING TO OWNER: ANY PAYMENTS MADE BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF COMMENCEMENT ARE CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713, PART I, SECTION 713.13, FLORIDA STATUTES, AND CAN RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE COMMENCING WORK OR RECORDING YOUR NOTICE OF COMMENCEMENT.

Signature of Owner or Print Name and Provide Signatory’s Title/Office Owner’s Authorized Officer/Director/Partner/Manager State of Florida County of Broward

The foregoing instrument was acknowledged before me this day of , 20

By , as

(name of person) (type of authority,…e.g. officer, trustee, attorney in fact) For . (name of party on behalf of whom instrument was executed)

Personally known or produced the following type of identification:

Notary

(Signature of Notary Public)

Under Penalties of perjury, I declare that I have read the foregoing and that the facts in it are true to the best of my knowledge and belief (Section 92.525, Florida Statutes).

Signature(s) of Owner(s) or Owner(s)’ Authorized Officer/ Director / Partner/Manager who signed above:

By By

Rev .08-09-07 (S.Recording)

FENCES FOR NEW OR EXISTING POOLS FLORIDA BUILDING CODE SECTION FBCB 454.2.17

1. FBCB 454.2.17.1.1 Maximum vertical clearance between grade and bottom of barriers shall be 2”

measured on the side of the barrier which faces away from the swimming pool.

2. FBCB 454.2.17. 1.4 Where the barrier is composed of horizontal and vertical members and the distance between the tops of the horizontal members is less than 45 inches, the horizontal members shall be located on the swimming pool side of the fence. Spacing between the vertical members shall not exceed 1-3/4” in width. Where there are decorative cutouts within the vertical members, spacing within the cutouts shall not exceed 1-3/4 inches in width.

3. FBCB 454.2.17.1.4 Where barrier is composed of horizontal members and the distance between the tops

of the horizontal members is 45 inches or more, spacing between vertical members shall not exceed 4 inches. Where there are decorative cutouts within vertical members, spacing in the cutouts shall not exceed 1-3/4 inches.

4. FBCB 454.2.17.1.6 Maximum mesh size for chain link fences shall be 2-1/4 inches square unless the

fence is provided with slats fastened at the top or bottom which reduce the openings to no more than 1-3/4 inches.

5. FBCB 454.2.17.1.7 Where the barrier is composed of diagonal members, the maximum opening formed

by the diagonal members shall not be more than 1-3/4 inches.

6. FBCB 454.2.17.1.8 Access gates when provided, shall be self-closing and shall comply with the requirements of Sections FBCB 454.2.17.1.1 through FBCB 454.2.17.1.7 and shall be equipped with a self-latching locking device located on the pool side of the gate. Where the device release is located no less than 54 inches from the bottom of the gate, the release mechanism may be located on either side of the gate and so placed that it cannot be reached by a young child over the top or through any opening or gap from the outside. Gates that provide access to the swimming pool must open outward away from the pool. The gates and barrier shall have no opening greater than ½ inch within 18 inches of the release mechanism.

I/WE THE UNDERSIGNED HAVE READ AND UNDERSTAND THE REQUIREMENTS OF THE FLORIDA BUILDING CODE FOR FENCE INSTALLATIONS ____________________________ _________________________________

OWNER CONTRACTOR

Florida Building Code Wood and Chain Link Fence Requirements FBC 1616.2.1 Fences. Fences not exceeding 6 feet (1829 mm) in height from grade maybe designed for 75 mph (33 m/s) fastest mile wind speed or 115 mph (40 m/s) 3-second gust. FBC 1616.2.1.1 Wood fences. Wood fence design shall be as specified by Section 2328. FBC 2328.1 Wood fences, so located on a property that by zoning regulations they cannot be used as a wall of a building, shall be constructed to meet the minimum specifications in Sections 2328.2 and 2328.3. FBC 2328.2 Fences not exceeding 6 feet (1829 mm) in height, shall be constructed to meet the following minimum requirements: from nominal 4-inch by 4-inch by 8-feet-long (102 mm by 102 mm by 2438 mm) posts No. 2 grade or better spaced 4-feet (1219 mm) on center, and embedded 2 feet (610 mm) into a concrete footing 10 inches (254 mm) in diameter and 2-feet (610 mm) deep. FBC 2328.3 Fences not exceeding 5 feet (1524 mm) or 4 feet (1219 mm) in height shall be constructed as provided in Section 2328.2, except that the spacing of posts may be increased to 5-feet (1524 mm) and 6-feet (1829 mm) on center for these heights, respectively.

WOOD FENCE TYPES

Board on Board Stockade Shadow Box Basket Weave

CHAIN LINK FENCE MINIMUM REQUIREMENTS

CHAIN LINK FENCES FLORIDA BUILDING CODE FBC 2224

CHAIN LINK FENCES OVER 12 FEET HIGH SHALL BE DESIGNED ACCORDING TO SECTION FBC 1616.1 CHAIN LINK FENCES LESS THAN 12 FEET HIGH MAY BE CONSTRUCTED IN ACCORD WITH TABLE 2224

Terminal Post Dimensions (In Inches)

(O.D. x Wall Thickness)

Line Post Dimensions (In Inches)

(O.D. x Wall Thickness)

Terminal Post Concrete Foundation Size

(Diameter X Depth) (In Inches)

Line Post Concrete Foundation Size

(Diameter X Depth) (In Inches)

Up to 4’ 2-3/8 x 0.0042 1-5/8 x 0.047 10 x 24 8 x 24 Over 4’ to 5’ 2-3/8 x 0.0042 1-7/8 x 0.055 10 x 24 8 x 24 Over 5’ to 6’ 2-3/8 x 0.0042 1-7/8 x 0.065 10 x 24 8 x 24 Over 6’ to 8’ 2-3/8 x 0.110 2-3/8 x 0.095 10 x 36 10 x 36 Over 8’ to 10’ 2-7/8 x 0.110 2-3/8 x 0.130 12 x 40 10 x 40 Over 10’ to 12’ 2-7/8 x 0.160 2-7/8 x 0.120 12 x 42 12 x 42

For SI: 1 Inch=25.4 mm. Notes: 1. This table is applicable only to fences with unrestricted airflow. 2. Fabric: 12 ½ gauge minimum. 3. Tension Bands: Use 1 less than the height of the fence in feet evenly spaced. 4. Fabric Ties: Must be Minimum the same gauge of the fabric. 5. Fabric Tie Spacing on the Top Rail: Five ties between the posts evenly spaced. 6. Fabric Tie Spacing on Line Posts: One less than the height of the fence in feet evenly spaced. 7. Either Top Rail or Top Tension wire shall be used. 8. Braces must be used at Terminal Posts if top tension wire is used instead of Top Rail. 9. Post Spacing: 10’ (3m) on center maximum. 10. Posts shall be embedded to within 6” (152m) from the bottom of the foundation. 11. In order to follow the contour of the land, the bottom of the fence may clear the contour of the ground by up to 5 inches (127mm) without increasing table values to the nest higher limit.

TOWN CODE SECTION 6-8

CONSTRUCTION FENCES

(1) Temporary perimeter site fencing for new construction is required and must meet all of

the following requirements: a. Be six feet high with approved screening material to prevent dust intrusion upon

adjacent properties. b. Be installed and maintained at ground level on all sides of the site. c. Include installation and maintenance of an approved silt fence at the property lines

and catch basins to prevent any construction debris from entering the waterway for properties abutting a waterway.

d. Be removed from the site upon completion of the exterior of the building or upon the issuance of a certificate of occupancy, whichever is sooner.

(2) Perimeter silt fencing for other construction projects may be required at the discretion of

the Building Official. (3) It is not intended that the temporary fencing required by this section be limited by required

setbacks.

ZONING REGULATIONS 30-313 (D) Fences, walls and hedges.

(1) Height, design, and location of fences, walls, hedges. a.

Height. The maximum height of any fence or wall shall be six feet, except where the fence or wall abuts property with business zoning, in which case the maximum height is eight feet. The height of fences, walls, hedges or plantings of whatever composition shall be measured from the natural contour of the ground on adjoining lots.

b. Construction. All fences and walls shall comply with the Florida Building Code.

c. Cement or concrete walls: 1.

Cement or concrete walls are permitted in all zoning districts, and must comply with the standards outlined in subsection 2., below.

2. Except when a new wall directly abuts an existing wall or fence preventing compliance with this requirement, walls shall be finished on both sides with materials satisfying industry standards, such as painted stucco, prefinished block, or other prefinished materials, shall be compatible with proposed or existing buildings, and shall meet the following design guidelines: i.

Cement or concrete walls in the RS-4, RS-5 and RD-10 zoning districts which exceed four feet in height must provide a minimum of 25 percent openings to allow air circulation.

ii. Walls shall be designed with changes in material, color, texture, or profile to avoid the massive, linear aspect and monotony of otherwise plain walls. Walls over two feet in height shall not form a continuous straight line without an offset, change of direction, or significant vertical feature every ten feet to break up the length of the wall.

iii. Walls shall include finishing features such as, but not limited to, changes in texture or color, variety of materials, capstones, decorative painting or bands of tile.

d. Fence/wall top features. The top of a fence or wall may contain architectural features and light fixtures. However, such features shall not extend more than 18 inches above the maximum height of the fence or wall, and the combined width of the features shall not exceed 20 percent of the total linear length of the fence or wall.

e. Gates. A fence or wall may have a pedestrian entrance with a gate. Such an entranceway, including any archway, may be no greater than eight feet in height, and no more than eight feet in width. Gates must swing or slide in a manner which does not obstruct public rights of way.

f. Maintenance. All fences and walls shall be maintained in good repair and in a secure manner. All defective structural and decorative elements shall be repaired or replaced in a workmanlike manner, to match as closely as possible the original materials and construction of the fence or wall. All surfaces shall have all graffiti and loose material removed. Any damaged portion of a fence or wall shall be repaired or replaced in a manner consistent with these standards. Any patching or resurfacing shall match the existing materials and shall be impervious to the elements, when possible.

g.

Hedges. 1.

All hedges shall be planted and maintained by property owners within the property lines and shall not encroach into the adjacent properties or right-of-way (ROW).

2. The height of a hedge shall be maintained not to exceed 12 feet in all zoning districts, except in the RM-25 district, where the height of a hedge is limited to four feet.

h.

Visibility limitations. No fences or walls shall be constructed within 25 feet of the front property line or within 30 feet of the clear site triangle at the corner of the property on residential lots. No walls, fences, hedges or plantings shall be planted or maintained to a height exceeding 30 inches above the crown of the roadway within sight visibility triangles: within 25 feet of the intersection of the front and side street property lines, within ten feet of any driveway, within ten feet from the intersection point of the edge of a driveway and alley or street, and within 15 feet from the intersection point of the extended property lines at an alley and a street.

i. Chain link fences. Chain link fences shall be completely hidden from view when viewed from any portion of the right-of-way in RS-5, RD-10 and RM-25 zoned property. Chain link fences are prohibited in any business zoning district.

j. Placement of finished side. Except when a new wall or fence directly abuts an existing wall or fence preventing compliance with this requirement, fences and walls finished on only one side shall be placed to have the finished side facing out. If a fence or wall is erected and any portion is placed with an unfinished side facing out due to an abutting obstacle, then that portion shall be finished within 180 days of the obstacle being removed.

k. Prohibited fence types. Barbed wire, electrified or razor wire fences, and fences or walls topped with barbed, electric or razor wire are prohibited, and shall not be erected or maintained on any property.

l. Zero lot line lots. Privacy fences and/or walls separating porches, patios, and pools along zero lot lines may be built to height not to exceed eight feet subject to building setback requirements of the residential zoning district where fence/walls are erected.

q)

All swimming pools shall be enclosed by an open mesh screen enclosure or a fence or wall a minimum of five feet in height of such design and material as will prevent unauthorized access to the pool area. All screen doors and fence gates shall be equipped with a self-locking mechanism.

EASEMENT AGREEMENT TOWN OF LAUDERDALE-BY-THE-SEA

Date: Attention:

I, propose to apply for a building permit to construct a

In the □ Utility Easement, □ Drainage Easement, □ Canal Maintenance

Easement, at my property located at

Legal Description: Lot Block Subdivision

TOWN OF LAUDERDALE-BY-THE-SEA. (SEE ATTACHED SURVEY)

A BRIEF DESCRIPTION OF THE TYPE OF CONSTRUCTION AND LOCATION OF THE PROPOSED CONSTRUCTION AS FOLLOWS.

I understand that your company will not be responsible in any way for repairs to, or replacement of, any portion of this And that any removal or replacement of this construction necessary for the use of

this easement will be done at my expense, I further understand that I will assume full responsibility for any damage incurred to the utility facilities during construction.

This is to certify that I am the lawful owner(s)

Signature of Owner Contact Phone Number

Address Return Fax Number

City State Zip Email Address

Note: This agreement shall be attached to the permit application when completed.

We □ Agree □ Disagree with the comments noted with the proposed construction based upon the circumstances statedherein:

Name of Utility Company: Representative: Title and Date:

Utility companies: AT&T Southeast (Bell South)

8601 W. Sunrise Boulevard. Plantation, Florida 33324 (Fax) Attn: Lisa Goltiz, Engineering 954-423-6108

Comcast Cable 2601 SW 145th Avenue, Suite 100 Miramar, Florida 33027

(Fax) Leonard Maxwell-Newbold 954-534-7008

Lauderdale-By-The-Sea 4501 N. Ocean Drive Lauderdale-By-The-Sea (Fax) Attn: Don Prince Public Works 954-640-4236

FP&L Customer Service Department 330 S.W. 12 Avenue Pompano Beach, Florida (Fax) Attn: Shavonti Archer, Engineering 954-956-2020

TECO (People’s Gas) Engineering Department 16101 W. Dixie Highway North Miami Beach, Florida 33162 (Fax) Attn: Yolanda, Engineering 1-305-945-0171

CONTRACTOR CONTACT NAME

PERMIT NUMBER CONTACT NUMBER

JOB ADDRESS

STRUCTURAL

Foundation Exterior Framing Wall Sheathing Columns Tie Beam Truss/Rafters Roof Sheathing Interior Framing Bucks Windows/Doors in progress Insulation Rock Base/ Forms Drywall/Screw Wire Lath Pool Steel Ceiling Grid Above Ceiling Penetrations Drive way Tin Cap and Accessories Mop in Progress Tile/Shingle in Progress Garage door Shutters Final Pool Final Fence Final Roof Final windows/doors Demolition Other Final

ZONING

Fence Pool Rock Base/Forms Driveway Slab/Deck/Patio Dock/Seawall Sign Other Final

PLUMBING

Rough Water Service Second Rough Top Out Fire Sprinkler Above Rough Fire Sprinkler Below Rough Fire Sprinkler Final Septic Tank Hook-up Roof Drains Gas-rough Inside Gas-rough Outside 200 PSI Test LP tank Well Lawn Sprinkler Rough Sewer Hook-up Main Drain Pool Piping Backflow Preventer Interceptor Catch Basins Condensate Drains Medical Gas Gas Final Lawn Sprinkler Final Demolition Other Final

MECHANICAL

Underground Piping Condensate Drains Rough Ductwork Exhaust Fans/Dryers Fire Dampers Smoke Dampers Ceiling Radiation Damper Hood Systems Rough Refrigerator/Walk Cooler/

Freezer Boiler Tanks Above Ground

Tanks Underground Demolition A/C Change Out Spray Booths Chimneys and Vents Cooling Towers/ Chiller

Systems Process Piping Fireplace Rough/

Ventilation Fireplace Final Hood Systems Final Other Final

Electrical

Meter Repair Temporary Pole 30 day Temporary Pool Grounding Underground Rough Slab Grounding Rough Ceiling Rough Telephone Rough Telephone Final Television Rough Intercom Rough Sound Rough Central vacuum Rough Service Upgrade Miscellaneous Repairs Pool Niche Light Wall Rough Generator Rough Fire Alarm Rough Television Final Intercom Final Alarm Final Sound Final Central Vacuum Final Demolition Other Final

Other not included

ALL NEW CONSTRUCTION, AND ADDITIONS; A SLAB SURVEY AND ELEVATION CERTIFICATE SHALL BE SUBMITTED AND APPROVED PRIOR TO A COLUMN OR TIE BEAM INSPECTION.

SWIMMING POOLS, SHALL HAVE A SPOT SURVEY APPROVED AFTER THE POOL IS GNITED AND PRIOR TO PERMITER PLUMBING/PRESSUR TEST INSPECTION.

A FINAL SURVEY IS REQUIRED PRIOR TO POOL BARRIER INSPECTION, DECK AND PERIMIETER FENCE INSPETION AND FINAL ELECTRIC INSPECTION.