MiniBlue™ II Pneumatic Applicators -...
Transcript of MiniBlue™ II Pneumatic Applicators -...
NORDSON CORPORATION DULUTH, GEORGIA USAwww.nordson.com
This document contains important safetyinformation Be sure to read and follow allsafety information in this document and anyother related documentation.
MiniBlue™ IIPneumatic Applicators
Customer Product ManualPart 1124393_01
Issued 05/2015
Part 1124393_01 E 2015 Nordson Corporation
For CE Declaration, refer to equipment documentation.
Nordson Corporation welcomes requests for information, comments, and inquiries about itsproducts. General information about Nordson can be found on the Internet using the following
address: http://www.nordson.com.
Address all correspondence to:
Nordson CorporationAttn: Customer Service11475 Lakefield DriveDuluth, GA 30097
Notice
This is a Nordson Corporation publication which is protected by copyright. Original copyright date2015. No part of this document may be photocopied, reproduced, or translated to another
language without the prior written consent of Nordson Corporation. The information contained inthis publication is subject to change without notice.
Trademarks
AccuJet, AeroCharge, Apogee, AquaGuard, Asymtek, Automove, Baitgun, Blue Box, Bowtie, Build-A-Part,CanWorks, Century, CF, CleanSleeve, CleanSpray, ColorMax, Color-on-Demand, Control Coat, Coolwave,
Cross-Cut, cScan+, Dage, Dispensejet, DispenseMate, DuraBlue, DuraDrum, Durafiber, DuraPail, Dura-Screen,Durasystem, Easy Coat, Easymove Plus, Ecodry, Econo-Coat, e.DOT, EFD, Emerald, Encore, ESP, e stylized,
ETI-stylized, Excel 2000, Fibrijet, Fillmaster, FlexiCoat, Flex-O-Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMix,Fulfill, GreenUV, HDLV, Heli-flow, Horizon, Hot Shot, iControl, iDry, iFlow, Isocoil, Isocore, Iso-Flo, iTRAX, Kinetix,
LEAN CELL, Little Squirt, LogiComm, Magnastatic, March, Maverick, MEG, Meltex, Microcoat, Micromark,Micromedics, MicroSet, Millennium, MiniBlue, Mini Squirt, Mountaingate, NexJet, Nordson, Optimum,
Package of Values, Pattern View, PermaFlo, PicoDot, Porous Coat, PowderGrid, Powderware, Precisecoat,PRIMARC, Printplus, Prism, ProBlue, Prodigy, Pro-Flo, ProLink, Pro-Meter, Pro-Stream, RBX, Rhino, Saturn,Saturn with rings, Scoreguard, Seal Sentry, Select Charge, Select Coat, Select Cure, Signature, Slautterback,Smart-Coat, Solder Plus, Spectrum, Speed-Coat, SureBead, Sure Coat, Sure-Max, Sure Wrap, Tracking Plus,TRAK, Trends, Tribomatic, TrueBlue, TrueCoat, Tubesetter, Ultra, UpTime, u-TAH, Value Plastics, Vantage,
VersaBlue, Versa-Coat, VersaDrum, VersaPail, Versa-Screen, Versa-Spray, VP Quick Fit, Watermark,and When you expect more. are registered trademarks of Nordson Corporation.
Accubar, Active Nozzle, Advanced Plasma Systems, AeroDeck, AeroWash, AltaBlue, AltaSlot, Alta Spray, Artiste,ATS, Auto-Flo, AutoScan, Axiom, Best Choice, Blue Series, Bravura, CanPro, Champion, Check Mate, ClassicBlue,Classic IX, Clean Coat, Cobalt, Controlled Fiberization, Control Weave, ContourCoat, CPX, cSelect, Cyclo-Kinetic,
DispensLink, Dry Cure, DuraBraid, DuraCoat, DuraPUR, Easy Clean, EasyOn, EasyPW, Eclipse, e.dot+,E-Nordson, Equalizer, EquiBead, FillEasy, Fill Sentry, Flow Coat, Fluxplus, Get Green With Blue, G-Net, G-Site,IntelliJet, iON, Iso-Flex, iTrend, Lacquer Cure, Maxima, Mesa, MicroFin, MicroMax, Mikros, MiniEdge, Minimeter,
Multifill, MultiScan, Myritex, Nano, NexJet, OmniScan, OptiMix, OptiStroke, Partnership+Plus, PatternJet,PatternPro, PCI, PharmaLok, Pinnacle, Plasmod, Powder Pilot, Powder Port, Powercure, Process Sentry,Pulse Spray, PURBlue, PURJet, Ready Coat, RediCoat, RollVIA, Royal Blue, Select Series, Sensomatic,
Shaftshield, SheetAire, Smart, Smartfil, SolidBlue, Spectral, SpeedKing, Spray Works, StediFlo, StediTherm,Summit, SureFoam, Sure Mix, SureSeal, Swirl Coat, TAH, ThruWave, Trade Plus, Trilogy, Ultra FoamMix, UltraMax,
Ultrasaver, Ultrasmart, Universal, ValueMate, Versa, Vista, Web Cure, YESTECH, and 2 Rings (Design)are trademarks of Nordson Corporation.
Designations and trademarks stated in this document may be brands that, when used by third parties for their ownpurposes, could lead to violation of the owners' rights.
Never Seez is a registered trademark of Bostik Inc.
Viton is a registered trademark of DuPont Dow Elastomers. L.L.C.
Table of Contents i
Part 1124393_01E 2015 Nordson Corporation
Table of Contents
Safety 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Safety Alert Symbols 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Responsibilities of the Equipment Owner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Instructions, Requirements, and Standards 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .User Qualifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applicable Industry Safety Practices 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Use of the Equipment 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Instructions and Safety Messages 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation Practices 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operating Practices 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintenance and Repair Practices 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment Safety Information 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Equipment Shutdown 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .General Safety Warnings and Cautions 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Other Safety Precautions 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .First Aid 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Labels and Tags 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MiniBlue II Expansion Applicators 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Freedom™ Applicators 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solenoid Valve 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dispensing Module 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EasyOn™ Feature 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hose Connector/Filter 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cordset 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Temperature Control 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Use 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Auxiliary Devices and Spare Parts 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Items Needed 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation Guidelines 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydraulic and Pneumatic Connections 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking and Inspection 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mounting the Applicator 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting an Applicator on a New or Existing System 21. . . . . . . . . . . . . . . . . . . . .Replacing an Applicator on an Existing System 22. . . . . . . . . . . . . . . . . . . . . . . . .
Making the Solenoid Valve Connections 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Connect the Air Supply 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Connect the Triggering Device to a Solenoid Valve 23. . . . . . . . . . . . . . . . . . . . . .
Connecting the Hose 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Flushing the Applicator 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contentsii
Part 1124393_01 E 2015 Nordson Corporation
Operation 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cleaning Nozzles 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Troubleshooting Table for MiniBlue 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inspecting the Applicator Wiring 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Diagnostic Procedures (DPs) 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DP1. Check a Solenoid Valve 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DP2. Check for a Clogged Nozzle or Module 35. . . . . . . . . . . . . . . . . . . . . . . . . . . .DP3. Check a Heater 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DP4. Check an RTD 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacing the Plastic Cover (SlimLine Applicators Only) 38. . . . . . . . . . . . . . . . . . . .Replacing a Module 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacing a Heater or RTD 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Replace the RTD 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .To Replace the Heater 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing a Solenoid Valve 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Illustrated Parts Lists 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SlimLine Single Module Applicator Assembly 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Single Wide and Multi Module Applicator Assembly 47. . . . . . . . . . . . . . . . . . . . . . . .Replacement Modules 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cordsets 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solenoid and Accessories 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Solenoids 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solenoid Cabling 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solenoid Hard Tubing Replacements Kits 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solenoid Optional Flexible Tubing Connection Kits 52. . . . . . . . . . . . . . . . . . . . . .Solenoid Accessories and Spare Parts 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Covers and Gaskets 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Non SlimLine Mounting 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hose Connectors and Filter Assemblies 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Filter Kits 57. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applicator-to-Hose Connectors 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Insulating Cuffs 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Standard Saturn Nozzles 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MiniBlue II Sure Bead Nozzles 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Heaters 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SlimLine Applicator 59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Standard MiniBlue II Applicator 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Retro-Fit MiniBlue II Applicator 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Insulating Applicator Covers 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Extension Cables 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintenance Accessories 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents iii
Part 1124393_01E 2015 Nordson Corporation
Specifications 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MiniBlue II Applicator Configuration Code 65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contentsiv
Part 1124393_01 E 2015 Nordson Corporation
Page Intentionally left blank.
MiniBluet II Pneumatic Applicators 1
E 2015 Nordson Corporation Part 1124393_01
MiniBluet IIPneumatic Applicators
SafetyRead this section before using the equipment. This section contains recommendations andpractices applicable to the safe installation, operation, and maintenance (hereafter referredto as “use”) of the product described in this document (hereafter referred to as “equipment”).Additional safety information, in the form of task-specific safety alert messages, appears asappropriate throughout this document.
WARNING! Failure to follow the safety messages, recommendations, and hazardavoidance procedures provided in this document can result in personal injury,including death, or damage to equipment or property.
Safety Alert SymbolsThe following safety alert symbol and signal words are used throughout this document toalert the reader to personal safety hazards or to identify conditions that may result in damageto equipment or property. Comply with all safety information that follows the signal word.
WARNING! Indicates a potentially hazardous situation that, if not avoided, canresult in serious personal injury, including death.
CAUTION! Indicates a potentially hazardous situation that, if not avoided, canresult in minor or moderate personal injury.
CAUTION! (Used without the safety alert symbol) Indicates a potentiallyhazardous situation that, if not avoided, can result in damage to equipment orproperty.
Responsibilities of the Equipment OwnerEquipment owners are responsible for managing safety information, ensuring that allinstructions and regulatory requirements for use of the equipment are met, and for qualifyingall potential users.
MiniBlue II Pneumatic Applicators2
Part 1124393_01 E 2015 Nordson Corporation
Safety InformationS Research and evaluate safety information from all applicable sources, including the
owner-specific safety policy, best industry practices, governing regulations, materialmanufacturer's product information, and this document.
S Make safety information available to equipment users in accordance with governingregulations. Contact the authority having jurisdiction for information.
S Maintain safety information, including the safety labels affixed to the equipment, inreadable condition.
Instructions, Requirements, and StandardsS Ensure that the equipment is used in accordance with the information provided in this
document, governing codes and regulations, and best industry practices.S If applicable, receive approval from your facility's engineering or safety department, or
other similar function within your organization, before installing or operating the equipmentfor the first time.
S Provide appropriate emergency and first aid equipment.S Conduct safety inspections to ensure required practices are being followed.S Re-evaluate safety practices and procedures whenever changes are made to the process
or equipment.
User QualificationsEquipment owners are responsible for ensuring that users:S receive safety training appropriate to their job function as directed by governing
regulations and best industry practicesS are familiar with the equipment owner's safety and accident prevention policies and
proceduresS receive equipment- and task-specific training from another qualified individual
NOTE: Nordson can provide equipment-specific installation, operation, andmaintenance training. Contact your Nordson representative for information
S possess industry- and trade-specific skills and a level of experience appropriate to theirjob function
S are physically capable of performing their job function and are not under the influence ofany substance that degrades their mental capacity or physical capabilities
Applicable Industry Safety PracticesThe following safety practices apply to the use of the equipment in the manner described inthis document. The information provided here is not meant to include all possible safetypractices, but represents the best safety practices for equipment of similar hazard potentialused in similar industries.
MiniBluet II Pneumatic Applicators 3
E 2015 Nordson Corporation Part 1124393_01
Intended Use of the EquipmentS Use the equipment only for the purposes described and within the limits specified in this
document.S Do not modify the equipment.S Do not use incompatible materials or unapproved auxiliary devices. Contact your Nordson
representative if you have any questions on material compatibility or the use ofnon-standard auxiliary devices.
Instructions and Safety MessagesS Read and follow the instructions provided in this document and other referenced
documents.S Familiarize yourself with the location and meaning of the safety warning labels and tags
affixed to the equipment. Refer to Safety Labels and Tags at the end of this section.S If you are unsure of how to use the equipment, contact your Nordson representative for
assistance.
Installation PracticesS Install the equipment in accordance with the instructions provided in this document and in
the documentation provided with auxiliary devices.S This equipment has not been certified for compliance with the ATEX directive nor as
nonincendive and should not be installed in potentially explosive environments.S Ensure that the equipment is rated for the environment in which it will be used and that the
processing characteristics of the material will not create a hazardous environment. Referto the Safety Data Sheet (SDS) for the material.
S If the required installation configuration does not match the installation instructions,contact your Nordson representative for assistance.
S Position the equipment for safe operation. Observe the requirements for clearancebetween the equipment and other objects.
S Install lockable power disconnects to isolate the equipment and all independentlypowered auxiliary devices from their power sources.
S Properly ground all equipment. Contact your local building code enforcement agency forspecific requirements.
S Ensure that fuses of the correct type and rating are installed in fused equipment.S Contact the authority having jurisdiction to determine the requirement for installation
permits or inspections.
Operating PracticesS Familiarize yourself with the location and operation of all safety devices and indicators.S Confirm that the equipment, including all safety devices (guards, interlocks, etc.), is in
good working order and that the required environmental conditions exist.S Use the personal protective equipment (PPE) specified for each task. Refer to Equipment
Safety Information or the material manufacturer's instructions and SDS for PPErequirements.
S Do not use equipment that is malfunctioning or shows signs of a potential malfunction.
MiniBlue II Pneumatic Applicators4
Part 1124393_01 E 2015 Nordson Corporation
Maintenance and Repair PracticesS Perform scheduled maintenance activities at the intervals described in this document.S Relieve system hydraulic and pneumatic pressure before servicing the equipment.S De-energize the equipment and all auxiliary devices before servicing the equipment.S Use only new Nordson-authorized refurbished or replacement parts.S Read and comply with the manufacturer's instructions and the SDS supplied with
equipment cleaning compounds.NOTE: SDSs for cleaning compounds that are sold by Nordson are available atwww.nordson.com or by calling your Nordson representative.
S Confirm the correct operation of all safety devices before placing the equipment back intooperation.
S Dispose of waste cleaning compounds and residual process materials according togoverning regulations. Refer to the applicable SDS or contact the authority havingjurisdiction for information.
S Keep equipment safety warning labels clean. Replace worn or damaged labels.
Equipment Safety InformationThis equipment safety information is applicable to the following types of Nordson equipment:S hot melt and cold adhesive application equipment and all related accessoriesS pattern controllers, timers, detection and verification systems, and all other optional
process control devices
Equipment ShutdownTo safely complete many of the procedures described in this document, the equipment mustfirst be shut down. The level of shut down required varies by the type of equipment in useand the procedure being completed.If required, shut down instructions are specified at the start of the procedure. The levels ofshut down are:
Relieving System Hydraulic PressureCompletely relieve system hydraulic pressure before breaking any hydraulic connection orseal. Refer to the melter-specific product manual for instructions on relieving systemhydraulic pressure.
MiniBluet II Pneumatic Applicators 5
E 2015 Nordson Corporation Part 1124393_01
De-energizing the SystemIsolate the system (melter, hoses, applicators, and optional devices) from all power sourcesbefore accessing any unprotected high-voltage wiring or connection point.1. Turn off the equipment and all auxiliary devices connected to the equipment (system).2. To prevent the equipment from being accidentally energized, lock and tag the disconnect
switch(es) or circuit breaker(s) that provide input electrical power to the equipment andoptional devices.
NOTE: Government regulations and industry standards dictate specific requirementsfor the isolation of hazardous energy sources. Refer to the appropriate regulation orstandard.
Disabling the ApplicatorsNOTE: Adhesive dispensing applicators are referred to as “applicators” in someprevious publications.
All electrical or mechanical devices that provide an activation signal to the applicators,applicator solenoid valve(s), or the melter pump must be disabled before work can beperformed on or around an applicator that is connected to a pressurized system.1. Turn off or disconnect the applicator triggering device (pattern controller, timer, PLC, etc.).2. Disconnect the input signal wiring to the applicator solenoid valve(s).3. Reduce the air pressure to the applicator solenoid valve(s) to zero; then relieve the
residual air pressure between the regulator and the applicator.
General Safety Warnings and CautionsTable 1 contains the general safety warnings and cautions that apply to Nordson hot meltand cold adhesive equipment. Review the table and carefully read all of the warnings orcautions that apply to the type of equipment described in this manual.
Equipment types are designated in Table 1 as follows:HM = Hot melt (melters, hoses, applicators, etc.)PC = Process controlCA = Cold adhesive (dispensing pumps, pressurized container, and applicators)
MiniBlue II Pneumatic Applicators6
Part 1124393_01 E 2015 Nordson Corporation
General Safety Warnings and Cautions
Table 1 General Safety Warnings and CautionsEquipment
TypeWarnings and Cautions
HM
WARNING! Hazardous vapors! Before processing anypolyurethane reactive (PUR) hot melt or solvent-based materialthrough a compatible Nordson melter, read and comply withthe material's SDS. Ensure that the material's processingtemperature and flashpoints will not be exceeded and that allrequirements for safe handling, ventilation, first aid, andpersonal protective equipment are met. Failure to comply withSDS requirements can cause personal injury, including death.
HMWARNING! Reactive material! Never clean any aluminumcomponent or flush Nordson equipment with halogenatedhydrocarbon fluids. Nordson melters and applicators containaluminum components that may react violently withhalogenated hydrocarbons. The use of halogenatedhydrocarbon compounds in Nordson equipment can causepersonal injury, including death.
HM, CAWARNING! System pressurized! Relieve system hydraulicpressure before breaking any hydraulic connection or seal.Failure to relieve the system hydraulic pressure can result inthe uncontrolled release of hot melt or cold adhesive, causingpersonal injury.
HMWARNING!Molten material! Wear eye or face protection,clothing that protects exposed skin, and heat-protective gloveswhen servicing equipment that contains molten hot melt. Evenwhen solidified, hot melt can still cause burns. Failure to wearappropriate personal protective equipment can result inpersonal injury.
Continued...
MiniBluet II Pneumatic Applicators 7
E 2015 Nordson Corporation Part 1124393_01
EquipmentType
Warnings and Cautions
HM, PCWARNING! Equipment starts automatically! Remote triggeringdevices are used to control automatic hot melt applicators.Before working on or near an operating applicator, disable theapplicator's triggering device and remove the air supply to theapplicator's solenoid valve(s). Failure to disable the applicator'striggering device and remove the supply of air to the solenoidvalve(s) can result in personal injury.
HM, CA, PC
WARNING! Risk of electrocution! Even when switched off andelectrically isolated at the disconnect switch or circuit breaker,the equipment may still be connected to energized auxiliarydevices. De-energize and electrically isolate all auxiliarydevices before servicing the equipment. Failure to properlyisolate electrical power to auxiliary equipment before servicingthe equipment can result in personal injury, including death.
HM, CA, PC
WARNING! Risk of fire or explosion! Nordson adhesiveequipment is not rated for use in explosive environments andhas not been certified for the ATEX directive or asnonincendive. In addition, this equipment should not be usedwith solvent-based adhesives that can create an explosiveatmosphere when processed. Refer to the SDS for theadhesive to determine its processing characteristics andlimitations. The use of incompatible solvent-based adhesivesor the improper processing of solvent-based adhesives canresult in personal injury, including death.
HM, CA, PCWARNING! Allow only personnel with appropriate training andexperience to operate or service the equipment. The use ofuntrained or inexperienced personnel to operate or service theequipment can result in injury, including death, to themselvesand others and can damage to the equipment.
Continued...
MiniBlue II Pneumatic Applicators8
Part 1124393_01 E 2015 Nordson Corporation
General Safety Warnings and Cautions (contd)
Table 1 General Safety Warnings and Cautions (contd)Equipment
TypeWarnings and Cautions
HMCAUTION! Hot surfaces! Avoid contact with the hot metalsurfaces of applicators, hoses, and certain components of themelter. If contact can not be avoided, wear heat-protectivegloves and clothing when working around heated equipment.Failure to avoid contact with hot metal surfaces can result inpersonal injury.
HM
CAUTION! Some Nordson melters are specifically designed toprocess polyurethane reactive (PUR) hot melt. Attempting toprocess PUR in equipment not specifically designed for thispurpose can damage the equipment and cause prematurereaction of the hot melt. If you are unsure of the equipment'sability to process PUR, contact your Nordson representative forassistance.
HM, CA
CAUTION! Before using any cleaning or flushing compound onor in the equipment, read and comply with the manufacturer'sinstructions and the SDS supplied with the compound. Somecleaning compounds can react unpredictably with hot melt orcold adhesive, resulting in damage to the equipment.
HM
CAUTION! Nordson hot melt equipment is factory tested withNordson Type R fluid that contains polyester adipateplasticizer. Certain hot melt materials can react with Type Rfluid and form a solid gum that can clog the equipment. Beforeusing the equipment, confirm that the hot melt is compatiblewith Type R fluid.
Other Safety PrecautionsS Do not use an open flame to heat hot melt system components.S Check high pressure hoses daily for signs of excessive wear, damage, or leaks.S Never point a dispensing hand-held applicator at yourself or others.S Suspend dispensing hand-held applicators by their proper suspension point.
MiniBluet II Pneumatic Applicators 9
E 2015 Nordson Corporation Part 1124393_01
First AidIf molten hot melt comes in contact with your skin:1. Do NOT attempt to remove the molten hot melt from your skin.2. Immediately soak the affected area in clean, cold water until the hot melt has cooled.3. Do NOT attempt to remove the solidified hot melt from your skin.4. In case of severe burns, treat for shock.5. Seek expert medical attention immediately. Give the SDS for the hot melt to the medical
personnel providing treatment.
Safety Labels and TagsFigure 1 illustrates the location of the product safety labels and tags affixed to the equipment.Table 2 provides an illustration of the hazard identification symbols that appear on eachsafety label and tag, the meaning of the symbol, or the exact wording of any safety message.
1
3
4
65
2
Figure 1: Safety labels and tags
MiniBlue II Pneumatic Applicators10
Part 1124393_01 E 2015 Nordson Corporation
Safety Labels and Tags (contd)
Table 2 Safety Labels and TagsItem Part Description1. N/A WARNING: Hot Surface! Before touching the applicator
body, allow the applicator to cool, or wearheat-protective gloves. Failure to allow the applicatorbody to cool or to wear heat-protective gloves maycause personal injury.
2. N/A WARNING: Disconnect power and remove systempressure before disassembly or maintenance. Failure tofollow these instructions may result in serious personalinjury.
3. 600137 WARNING: Disconnect power and remove systempressure before disassembly or maintenance. Failure tofollow these instructions may result in serious personalinjury.
4. 243352 WARNING: Fire, injury, or equipment damage can resultif cleanout materials do not meet the followingrequirements:a. Minimum flashpoint to be 550_F (288_C).b. Liquid and vapor to be non-toxic at use temperature in
equipment.c. Chemical reactions with adhesive and equipment
materials must not be violently heat producing.d. Cleanout material must not corrode or otherwise
weaken equipment materials.5. 600103 CAUTION: This applicator is RTD (resistance
temperature detector) controlled. Prior to operation andbefore changing adhesive, consult instruction manual forchanging operating temperature. Failure to followinstructions may result in personal injury or propertydamage.
6. 243352 CAUTION: This equipment is factory tested withNordson type R fluid containing Polyester Adipateplasticizer. Certain adhesives may reactwith the type R fluid residue to form solid gum, which canbe difficult to remove.To avoid equipment damage,check with adhesive supplier regarding compatibility andcleanout procedure before putting adhesive into thesystem.
MiniBluet II Pneumatic Applicators 11
E 2015 Nordson Corporation Part 1124393_01
DescriptionNordson MiniBlue II automatic applicators apply thermoplastic hot melt adhesive to aproduct, providing uniform bead deposition and improved cutoff when used with aggressiveor hard-to-dispense adhesives. Their air-open, air-close dispensing modules allow highcycle speeds and their compact size allows them to fit between the flaps of most cartons.
MiniBlue II applicators are available in a slim, 18 mm (0.71-in.) single-module design withoutplastic cover (34 mm [1.34 in.] with plastic cover), and in a variety of configurable designs,including single-module and multi-module configurations.
MiniBlue II applicators are manufactured according to the design choices made at the time oforder placement. Refer to Applicator Configuration Code under Technical Data at the end ofthis manual for more information.
MiniBlue II Expansion ApplicatorsMiniBlue II expansion applicators have been designed to fit directly into existing Solid Blueapplications with no modifications to mounting brackets. The nozzle tip is in the samelocation as legacy applicators, and the expansion applicators accommodate bar mountingand direct manifold mounting applications.
Freedom™ ApplicatorsFreedom applicators are based on the MiniBlue II platform, but can only be used as part of aFreedom Hot Melt Adhesive Dispensing System. As part of that system, the Freedomapplicator offers the following feature benefits:S Component RecognitionS On-screen system inventory at the melter, including part numbers and serial numbers.S Troubleshooting guidance.
S Freedom applicators only work with Freedom hoses.S Solenoid actuation signal routed through through the Freedom hose (single module
applicator only).S Melter integrated OptiBond™ bead stitching control, allowing for reduced adhesive
consumption (up to 4 channels per melter).
MiniBlue II Pneumatic Applicators12
Part 1124393_01 E 2015 Nordson Corporation
Description (contd)Figure 2 shows some typical MiniBlue II applicators. Figures 3 and 4 show the key parts oftwo typical MiniBlue II applicators.
NOTE: The illustrations in this manual depict typical MiniBlue II applicators. Yourapplicator may differ in appearance.
1 2
3
Figure 2: Typical MiniBlue II applicators1. SlimLine single-module applicator with SP solenoid
valve and plastic hard cover2. Wide single-module applicator with SP solenoid
valve, soft flexible cover and side mounted cordset
3. Multi module applicator with SPsolenoid valve
MiniBluet II Pneumatic Applicators 13
E 2015 Nordson Corporation Part 1124393_01
1
2
3
4
5
67
8
Figure 3: Key parts of a SlimLine single-module MiniBlue II ball and seat applicator1. Cordset2. Solenoid valve3. Mounting bracket4. Hose connector
5. Filter (integrated, not shown)6. Applicator cover7. Module (under the cover)8. Muffler
MiniBlue II Pneumatic Applicators14
Part 1124393_01 E 2015 Nordson Corporation
Description (contd)
2
1
3
4
5
6
7
Figure 4: Key parts of a multi-module MiniBlue II ball and seat applicator1. Cordset2. Solenoid valve3. Mounting bracket4. Hose connector/inline filter
5. Body6. Module7. Muffler
MiniBluet II Pneumatic Applicators 15
E 2015 Nordson Corporation Part 1124393_01
Solenoid ValveSee Figure 5. Solenoid valves may be configured for independent, common, or programmedmodule actuation, as described in Table 3.
CAUTION! SP, SP Waterwash, and P1 solenoids run at a maximum 24 VDC. Ifvoltage exceeds 24 VDC, premature failure will occur.
21 3
Figure 5: MiniBlue II Solenoid Valves1. SD Solenoid2. SP and SP Waterwash Solenoid
3. P1 Solenoid
MiniBlue II Pneumatic Applicators16
Part 1124393_01 E 2015 Nordson Corporation
Solenoid Valve (contd)
Table 3 Types of Module Air ActuationType of Actuation DescriptionIndependent One solenoid valve directly actuates one module. (SP, SD, P1)
NOTE: SD is not available on retrofit applicatorsCommon One solenoid valve actuates all modules.
NOTE: SP multi-module valves are the only option formulti-module CA applicators configurations.
NOTE: This type of actuation is not recommended for stitchingapplications.
Programmed Two solenoid valves actuate two groups (left and right) ofmodules.NOTE: An SP multi-module valve is the only option formulti-module PA applicators.
NOTE: This type of actuation is not recommended for stitchingapplications.
NOTE: Module performance will be sacrificed proportionately as more modules arecontrolled by a single solenoid valve (common or programmed actuation).
NOTE: SP valves are standard for single-module applications. SD valves are used inapplications with limited mounting space.
NOTE: Solenoid response drift comparison:P1: <1.0 msSP Single: <2.5 msSD: <5.0 msSP Multi: <5.0 ms
MiniBluet II Pneumatic Applicators 17
E 2015 Nordson Corporation Part 1124393_01
Dispensing ModuleBall-and-seat modules are used in combination with Saturn nozzles, allowing easierchange-out of nozzle sizes and eliminating the need to stock multiple reduced-cavitymodules with different orifice sizes. Needle-and-seat modules are used in combination withSureBead nozzles. SureBead nozzles perform similar to reduced cavity and zero cavitynozzles. Because of improved design efficiency, adhesive bead volume may vary slightlyfrom equivalent Blue Series RC and ZC modules. Adjust the adhesive pressure tocompensate.
A MiniBlue II applicator may have 1-8 modules. Air is supplied constantly to a modulethrough a solenoid valve. When the applicator is not being triggered, air will flow through themodule's air-close port to keep the module needle on its seat. When triggered, the solenoidvalve will direct air into the air-open port, lifting the needle from its seat to dispense theadhesive.
EasyOn™ FeatureSee Figure 6. All MiniBlue II applicators use the EasyOn feature. The EasyOn feature on themodule mates with the EasyOn feature on the applicator body. The EasyOn feature allowsthe module to be installed onto the applicator body, regardless of the orientation of theapplicator body.
Figure 6: EasyOn design
MiniBlue II Pneumatic Applicators18
Part 1124393_01 E 2015 Nordson Corporation
Hose Connector/FilterTable 4 shows the filter options based on the style of applicator you have.
See Figure 7. All MiniBlue II applicators have a straight, 45-degree, or 90-degree hoseconnector and either an integrated or an inline Saturn filter. Saturn filters are available in 50,100 or 200 mesh screens to meet your requirements.
Table 4 MiniBlue II Selection Options
Applicator TypeMiniBlue II
Standard Expansion ApplicatorsSpring Closed Air Closed
SlimLine SingleModule Integrated Filter ------ ------
Wide Body SingleModule Inline Filter Integrated Filter Integrated Filter
ConfiguredMulti-Module Inline Filter Inline Filter Inline Filter
1
2
3
Figure 7: Location of hose connectors and Saturn filters on different applicatorconfigurations
1. Hose connector (45 degree shown)2. Integrated filter (SlimLine single-module applicator)
3. Hose connector/inline filter(45 degree shown)
MiniBluet II Pneumatic Applicators 19
E 2015 Nordson Corporation Part 1124393_01
CordsetThe applicator cordset may be positioned on either the right or left end, or on the right or leftside of the back of configurable multi-module applicators.
Only top mounted cordsets are available on SlimLine applicators.
See Figure 8. Cordsets are available in water-resistant and T-style versions.
12
3
Figure 8: Cordset types1. Freedom cordset2. T-style cordset
3. Water-resistant cordset
Temperature ControlAll MiniBlue II applicators use 120-ohm nickel resistance temperature detectors (RTDs) forprecise temperature sensing and for applicator temperature control to within +0.5 _C (1.0 _F)of a setpoint temperature.
Intended UseMiniBlue II applicators are specifically designed for industrial applications that require thedeposition of a precisely controlled bead of hot melt material onto a moving substrate. Theapplicators are designed to be rigidly mounted, pneumatically operated, and triggered by aNordson-approved, electrically controlled solenoid valve. MiniBlue II applicators aredesigned for use with Nordson melters and hoses.
Auxiliary Devices and Spare PartsMiniBlue II applicators should only be connected to approved auxiliary devices. Use onlynew Nordson replacement parts or approved factory refurbished parts.
MiniBlue II Pneumatic Applicators20
Part 1124393_01 E 2015 Nordson Corporation
InstallationApplicators are installed using the following six-step process:S unpack and inspectS mountS connect the air supplyS connect the hoseS flushS install nozzles
Applicators ordered with special options may require additional installation steps that are notdescribed here.
NOTE: Nozzles must be ordered separately. Refer to Parts for nozzle part numbers.
Items NeededTo ensure a smooth installation, have the following items on hand:S personal protective equipment for working with hot adhesiveS product manuals for associated equipment (melter, hose, etc.)S device to lift and position the applicatorS mounting equipment, such as a mounting rod, appropriate for the parent machineS wiring and 24 VDC power supply for the solenoid valveS air pressure regulator and air line tubing (Refer to Connect the Air Supply provided in
the following pages).S automatic applicator hoseS set of standard and metric hex-head wrenchesS flat-blade and Phillips-head screwdriversS drain pans and waste containers suitable for waste adhesiveS O-ring lubricantS anti-seize lubricant
MiniBluet II Pneumatic Applicators 21
E 2015 Nordson Corporation Part 1124393_01
Installation GuidelinesUse the following installation guidelines for optimum applicator performance.
MountingS Mount the applicator such that the nozzle will be as close as possible to the substrate, but
at a distance that works best for your application. Typically, the minimum distance is twotimes the diameter of the nozzle orifice.
S Ensure that the mounting location provides sufficient clearance around the rear or sides ofthe applicator to allow for removal of the manifold covers.
S Mount the applicator on a rigid support that is isolated from external vibrations and thatprevents the applicator from rotating.
S Insulate the applicator from the support using the insulator provided with the applicator.S Do not remove the nozzle from the SureBead applicator until it is time to start the system
and flush the applicator.
Hydraulic and Pneumatic ConnectionsS Use only one fitting to connect a hose to a hose connector on the applicator.S Insulate hose-to-applicator joints. Insulating cuffs may be ordered separately. Refer to
Parts.S Use only clean, dry, non-lubricated air.S Ensure that the plant air supply and regulator provide a minimum of 4 bar (58 psig) to the
applicator solenoid valve.
Unpacking and Inspection1. Carefully unpack the applicator.2. Inspect the applicator and inventory the contents of the shipping package. applicators are
shipped fully assembled and typically include the following components:S mounting clampS module(s)S solenoid valve(s)Applicators ordered with optional features may be shipped with additional components.
Mounting the ApplicatorThis section describes the following applicator-mounting options:S mounting a applicator on a new or existing systemS replacing a applicator on an existing system
The configuration of your equipment and production line may require a variation in themounting options described in this section. Regardless of the mounting method used, followthe guidelines provided in Installation Guidelines.
MiniBlue II Pneumatic Applicators22
Part 1124393_01 E 2015 Nordson Corporation
Mounting an Applicator on a New or Existing System1. See Figure 9. Slide the applicator mounting clamp(s) onto a 12-mm, 13-mm, or 0.5 in.
mounting bar, or disassemble the clamp(s) and reassemble them (with the applicator andinsulators) onto the mounting bar. Ensure that the insulators are placed between themanifold and the clamp(s).
1(12 mm, 13 mm or0.5 in. diameter)
23
Figure 9: Mounting an applicator using the mounting clamp (SlimLine applicator shown)1. Mounting bar2. Clamp
3. Insulator
2. Securely tighten the mounting clamp(s).3. Go toMaking the Solenoid Valve Connections.
MiniBluet II Pneumatic Applicators 23
E 2015 Nordson Corporation Part 1124393_01
Replacing an Applicator on an Existing SystemNOTE: MiniBlue II applicators are preassembled with a Nordson-approved,performance-matched solenoid valve.
NOTE: The distance from the mounting rod centerline and the nozzle tip is different ona slim single-module applicator and a single-module configurable applicator. If you arereplacing a single-module applicator, be sure to the replace the correct applicator style.
1. Relieve system hydraulic pressure and disable the applicator to be replaced. Refer toSafety.
2. Disconnect the hose from the applicator both electrically and hydraulically.3. Separate the existing applicator from its mounting. If a mounting clamp will not be reused,
remove it from the mounting bar.4. Mount the new applicator and insulator onto the existing mounting clamp (or rod) or
disassemble a new applicator's mounting clamp and then reassemble the clamp (with theapplicator and insulator) onto the existing mounting bar. Tighten the clamp securely.
5. Go toMaking the Solenoid Valve Connections.
Making the Solenoid Valve ConnectionsSolenoid valves must be connected to:S an air supplyS a triggering device, such as a pattern controller or timer
Be sure to refer to the correct triggering device connection procedure for the solenoid valveon your applicator.
Connect the Air SupplyConnect a clean, dry, non-lubricated air supply to the air inlet on the solenoid valves.
CAUTION! The air line tubing should be 6 mm OD x 4 mm ID for IndependentActuation (IA) solenoids/applicators, 10 mm OD x 8 mm ID (without adapter) or8 mm OD x 6 mm ID (with adapter) for Continuous Actuation (CA) or ProgrammedActuation (PA) solenoids/applicators. Using tubing smaller than that specifiedmay negatively affect applicator performance.
NOTE: Refer also to Installation Guidelines earlier in this section and, if applicable, tothe instructions supplied with the solenoid valve.
MiniBlue II Pneumatic Applicators24
Part 1124393_01 E 2015 Nordson Corporation
Connect the Triggering Device to a Solenoid ValveSee Figures 10 and 11. Connect the solenoid valve cable to the solenoid valve and to thetriggering device.
NOTE: Refer to Solenoid, Tubing and Fittings table in the Parts section for the cablepart numbers.
SP and SP Waterwash SolenoidsCAUTION! Do not use a spiked signal. Doing so will destroy the internally spikedvalve.
1. Connect the brown and blue wires to the 24 VDC signal.
Brown: 24VDC
Black: Not used
Blue: Common
Figure 10: Connecting the cable to an SP and waterwash solenoid valves
MiniBluet II Pneumatic Applicators 25
E 2015 Nordson Corporation Part 1124393_01
SD SolenoidNOTE: This cable is approved for non-spiked Nordson pattern controllers with SDsolenoid valves. If used with third-party timers, make sure the output is voltageprotected for inductive loads to avoid damage to the timer.
1. Connect the brown and black wires to the 24 VDC signal.
Brown: 24 VDC
Black: Common
Blue: Not used
Figure 11: Connecting the cable to an SD solenoid valve
MiniBlue II Pneumatic Applicators26
Part 1124393_01 E 2015 Nordson Corporation
P1 SolenoidCAUTION! Do not use a spiked signal. Doing so will destroy the internally spikedvalve.
1. Connect the brown and blue wires to the 24 VDC signal.
Brown: 24VDCBlack: Not used
Blue: Common
Figure 12: Connecting the cable to the P1 solenoid valve
NOTES:S P1 requires 1123970 and either 1100687 or 1100688.S Cable 1123970 includes a circuit that limits the maximum current draw of the attached
solenoid valve.
MiniBluet II Pneumatic Applicators 27
E 2015 Nordson Corporation Part 1124393_01
Attach Accessories to the SP Waterwash SolenoidUse the waterwash solenoid accessory kit (P/N 1124349) to complete the instructionsgiven below. This kit is intended for use with SP waterwash solenoids, P/Ns 1124235and 1124238.
2
13
4
Figure 13: Connecting the exhaust muffler relocation kit to a waterwash solenoid valve1. Fittings2. Tubes
3. Unions4. Mufflers
1. Make sure that the system is de-energized and the applicator is disabled. Refer toSafety given earlier in this manual.
2. Using an M4 Hex key attach the two fittings into the solenoid's exhaust ports.3. Insert a tube into each of the fitting. Make sure it is secure.4. Install a union onto the opposite end of each of the tube.5. Insert a muffler into each of the union.6. Route the tubes downward and away from the applicator.
IMPORTANT: Be sure to secure the ends of the tubes with the Velcro strap provided inthe kit.
7. Resume normal operation.
MiniBlue II Pneumatic Applicators28
Part 1124393_01 E 2015 Nordson Corporation
Connecting the HoseNOTE: Refer to the user's guide shipped with the hose for detailed hose installationguidelines.
1. Connect the hose to the applicator.2. Connect the applicator cordset to the hose.3. Connect the hose to the melter. Refer to the hose user's guide and/or the melter product
manual as needed.4. Go to Flushing the Applicator.
MiniBluet II Pneumatic Applicators 29
E 2015 Nordson Corporation Part 1124393_01
Flushing the ApplicatorBefore the applicator is placed into operation, it must be flushed of foreign material.
WARNING! Risk of personal injury or equipment damage. Do not remove thenozzle from SureBead applicators until it is time to start the system and flush theapplicators. The sharp needle on these applicators is exposed whenever thenozzle is removed.
CAUTION! This equipment is factory tested with Nordson Type R fluid containingpolyester adipate plasticizer. Certain adhesives may react with the Type R fluidresidue to form a solid gum that can be difficult to remove. Consult with youradhesive supplier to determine the compatibility of your adhesive with Type Rfluid.
1. Disconnect or turn off the solenoid valve triggering device.2. Start the melter and heat the system to the operating temperature and pressure required
for the adhesive being used. Refer to the melter product manual and the instructionsprovided with the adhesive as needed.
3. Place a drain pan under the applicator.4. Remove the nozzle(s) from the applicator. Refer to the nozzle removal procedures under
Cleaning Nozzles later in this manual as needed.5. Dispense adhesive from the applicator by manually triggering the solenoid valve(s).6. Stop dispensing when the adhesive flow is clear and free of foreign material.7. Check for leaks between the applicator, hose, and melter.8. Install the applicator nozzles.
SureBead nozzles: Install the nozzle by threading it onto the module by hand and thenusing a torque wrench to tighten the nozzle to no more than 4.5 Nm (40 in.-lb). Do notover-tighten. Refer to the nozzle installation procedures under Cleaning Nozzles later inthis manual as needed.
MiniBlue II Pneumatic Applicators30
Part 1124393_01 E 2015 Nordson Corporation
OperationRefer to the melter product manual for operating instructions.
WARNING! MiniBlue II applicator modules operate as air-open, air-close valves.The loss or elimination of air pressure to the applicator solenoid valve without acorresponding reduction in system hydraulic pressure may cause the applicatormodules to remain open.
MaintenanceTable 5 provides the recommended schedule for applicator maintenance. Detailedprocedures for weekly and semi-annual maintenance tasks are provided in the remainder ofthis section.
Table 5 Applicator Maintenance ScheduleFrequency Task Notes
Daily Remove hot melt and charfrom the exterior of theapplicator assembly.
Weekly Clean the applicatornozzle(s). Refer toCleaning Nozzles.
A, B
Semi-annually Inspect the applicatorwiring. Refer to Inspectingthe applicator Wiring.
As needed Replace the filter. Refer tothe instructions suppliedwith the replacement filter.
NOTE A: Nordson recommends the use of a nozzle cleaning kit.B: Process-specific nozzle performance history may indicate the need for more or less
frequent nozzle cleaning.
MiniBluet II Pneumatic Applicators 31
E 2015 Nordson Corporation Part 1124393_01
Cleaning NozzlesWARNING! Risk of personal injury or equipment damage. Do not remove thenozzle from SureBead applicators until it is time to start the system and flush theapplicators. The sharp needle on these applicators is exposed whenever thenozzle is removed.
Applicator nozzles may become clogged when char, a by-product of overheating the hotmelt, becomes lodged in the nozzle.1. Heat the applicator to operating temperature.2. Disable the applicator. Refer to Safety.3. Remove the nozzle. Refer to Table 6.
Table 6 Nozzle removal proceduresNozzle Type Nozzle Removal Procedure
Saturn
SureBead
Use a wrench to loosen the nozzle; then remove thenozzle by hand.
WARNING! Risk of fire. Do not heat Nordson Type R fluid above 245 _C (475 _F).Use only an industrial grade, regulated, electrical heating device that is designedto heat industrial fluids. Personal injury or property damage can result if Type Rcleaning fluid is heated with an open flame or in an unregulated heating device.
4. Soak the nozzles in Nordson Type R cleaning fluid that has been heated above themelting point of the adhesive, to a maximum of 177 _C (350 _F).
5. Remove the nozzles from the cleaning fluid.
CAUTION! Use the correct size precision pin probe to clean Nordson nozzles.The use of non-precision or incorrectly sized probes may damage the nozzle. TheNordson nozzle cleaning kit (part 901915) contains a variety of probe sizes.
MiniBlue II Pneumatic Applicators32
Part 1124393_01 E 2015 Nordson Corporation
Cleaning Nozzles (contd)6. See Figure 14. At the outlet of each nozzle, insert a correctly sized cleaning probe.7. With a clean cloth, firmly grip the cleaning probe, then pull the probe out of the nozzle,
wiping the probe clean.
Figure 14: Cleaning a nozzle8. Reinstall the nozzle. Refer to Table 7.
Table 7 Nozzle installation proceduresNozzle Type Nozzle Installation Procedure
Saturn
SureBead
Thread the nozzle onto the module threads by hand;then use a torque wrench to tighten the nozzle to4.5 NDm (40 in.-lb).
9. Restore the system to normal operation.
MiniBluet II Pneumatic Applicators 33
E 2015 Nordson Corporation Part 1124393_01
TroubleshootingWARNING! Allow only personnel with appropriate training andexperience to operate or service the equipment. The use ofuntrained or inexperienced personnel to operate or service theequipment can result in injury, including death, to themselves andothers, and damage to the equipment.
Troubleshooting Table for MiniBlue IIThe following table lists the applicator problems that are most likely to occur, the possiblecauses of each problem, and steps for corrective action. Where applicable, cross-referencesare made to expanded diagnostic procedures (DPs) provided later in this section or to othersections of this manual.
Problem Possible Cause Corrective Action1. No adhesive flow
from a singleapplicator moduleor from anymodule on amulti-moduleapplicator
Adhesive level low Add adhesive.
No input power Connect power to the melterand auxiliary devices. Ensurethat all disconnect switches orcircuit breakers are on.
Melter, hose, or applicatortemperature setting too low
Adjust the setting. Refer to themelter product manual.
System not at operatingtemperature
Verify that the system readylight is on and that the adhesiveis molten.
Insufficient air pressure tomelter piston pump (pistonpump melters)
Adjust the pump air pressure.
Melter motor not operating(gear pump melters)
Check the motor operation.Refer to the melter productmanual.
No air supply to solenoidvalve
Check the plant air supplypressure.
Solenoid valve failed Check the solenoid valve andreplace if necessary. Refer toDP1.
Hose clogged Replace the hose.Continued...
MiniBlue II Pneumatic Applicators34
Part 1124393_01 E 2015 Nordson Corporation
Troubleshooting Table for MiniBlue II (contd)
Problem Possible Cause Corrective Action1. No adhesive flow
from a singleapplicator moduleor from anymodule on amulti-moduleapplicator(contd)
Nozzle clogged Check the nozzle. Refer to DP2.
Adhesive in air section ofmodule
Replace the module. Refer tothe instructions provided withthe module.
Module failed Replace the module. Refer tothe instructions provided withthe module.
Dirty or faulty triggeringdevice
Clean or replace the triggeringdevice.
Faulty encoder Test the encoder and replace ifdefective.
2. No adhesive flowfrom somemodules in amulti-moduleapplicator
Nozzle clogged Check the nozzle. Refer to DP2.
Module failed Replace the module. Refer tothe instructions provided withthe module.
3. Uncontrolledadhesive flowfrom module
Hydraulic pressure toohigh
Decrease the system hydraulicpressure.
Hydraulic pressure toohigh and applicator airpressure lost
Stop the melter pump andrestore the air pressure to theapplicator.
Module failed to open Replace the module. Refer tothe instructions provided withthe module.
Solenoid valve ported tomanifold backwards orfailed to open
Correct the solenoid valveporting or replace the solenoidvalve. If applicable, refer to theinstructions supplied with thesolenoid valve.
4. Adhesive or airflows from bleedhole
Air or adhesive seals failed Replace the module. Refer tothe instructions provided withthe module.
Continued...
MiniBluet II Pneumatic Applicators 35
E 2015 Nordson Corporation Part 1124393_01
Problem Possible Cause Corrective Action5. Modules not
triggering at thesame time onmulti-moduleapplicator
Module failed Replace the module. Refer tothe instructions provided withthe module.
Insufficient applicator airpressure
Increase the applicator airpressure.
6. Applicator fails toheat orunderheats
No power Check that the melter is on.Refer to the melter productmanual.
Applicator temperaturesetpoint too low
Adjust the temperature setpoint.Refer to the melter productmanual.
Applicator heater failed(open or short)
Check for an open heater circuit.Refer to DP3.
Applicator RTD failed(open or short)
Check the RTD resistance.Refer to DP4.
7. Applicatoroverheats
Tank, hose, or applicatortemperature setpoint toohigh
Adjust the setpoint. Refer to themelter product manual.
Applicator RTD shorted(melter should shut down)
Check the RTD resistance.Refer to DP4.
Short in heater controlcircuit
Troubleshoot the melter. Referto the melter product manual.
8. Freedom melterdoes notacknowledge thatan applicator isinstalled.
Component ID (CID) notinstalled or not recognized.
Refer to Freedom Hot MeltAdhesive System Manual.
9. Freedom melterdoes acknowledgethat an applicatoris installed butdoes notrecognize asFreedomapprovedapplicator.
Non-Freedom Applicatorinstalled
Refer to Freedom Hot MeltAdhesive System Manual.
Damaged or misconnectedRTD or cordset.
See pin out and verify RTD andheater resistance.
10. Freedomapplicator is notstitching(modulating)beads whendispensing.
Refer to Freedom Hot MeltAdhesive System Manual.
Refer to Freedom Hot MeltAdhesive System Manual.
MiniBlue II Pneumatic Applicators36
Part 1124393_01 E 2015 Nordson Corporation
Inspecting the Applicator Wiring1. De-energize the system. Refer to Safety.2. Remove the plastic cover (SlimLine single module applicators only). Refer to Replacing
the Plastic Heater Cover (SlimLine Applicators Only).3. Remove the manifold cover.4. Check the internal applicator wiring for signs of damage and the cable connection for
tightness.5. Reinstall the manifold cover.
MiniBluet II Pneumatic Applicators 37
E 2015 Nordson Corporation Part 1124393_01
Diagnostic Procedures (DPs)The following diagnostic procedures (DPs) are referenced in the Troubleshooting Table.
DP1. Check a Solenoid Valve1. Place the system into operation.2. Trigger the applicator using the timer or pattern controller:S Adhesive flows—normal indication. Return to the Troubleshooting Table.S No adhesive flow—go to step 3.
3. Manually trigger the applicator at the solenoid valve:S Adhesive flows—normal indication. Return to the Troubleshooting Table.S No adhesive flow—go to step 4.
4. Check the solenoid valve coil for continuity (P1, SG and SD Valves):S Continuity okay—normal indication. Return to the Troubleshooting Table.S No continuity—failed solenoid valve. Replace the solenoid valve.
NOTE: Verify that the solenoid valve being used has a rated service temperatureabove 85 _C (185 _F).
DP2. Check for a Clogged Nozzle or Module1. Disable the applicator. Refer to Safety.2. Remove the nozzle. Refer to Cleaning Nozzles for the nozzle-removal procedure.3. Place the applicator back into operation.4. Trigger the applicator:S Adhesive flows—normal indication. Clean the nozzle. Refer toMaintenance.S No adhesive flow—the module is clogged. Replace the module. Refer to Repair.
MiniBlue II Pneumatic Applicators38
Part 1124393_01 E 2015 Nordson Corporation
DP3. Check a Heater1. Disable the applicator. Refer to Safety.2. Unplug the applicator cordset from the hose.3. See Figure 15. Test for continuity across the heater circuit (pins 1 and 2):S Continuity okay—normal indication. Return to the Troubleshooting Table.S No continuity—the heater is defective. Replace the heater. Refer to Repair.
1
2
3 4
5
6
1235
HEATERHEATERRTDRTDGND
412
34
5
1
2
3 4
5
6
1235
HEATERHEATERRTD
RTD CommonGun CID Data
46
Applicator CID Common
FreedomWiring:
Figure 15: Applicator cordset pin positions
DP4. Check an RTD1. Disable the applicator. Refer to Safety.2. Unplug the applicator cordset from the hose.3. Allow the applicator to reach room temperature or use a pyrometer to determine the
temperature of the applicator.4. See Figure 15. When the applicator temperature is known, measure the resistance across
the RTD circuit (pins 3 and 5).
MiniBluet II Pneumatic Applicators 39
E 2015 Nordson Corporation Part 1124393_01
5. See Figure 16 to determine the expected resistance of the RTD at the known temperature.Compare the expected and measured resistance values.
4209012A
Resistancein Ohms
Temperature in F
Temperature in CNickel RTD
Figure 16: RTD resistance vs. temperatureS Measured resistance is within the expected range—normal indication. Return to the
Troubleshooting Table.S Measured resistance is not within the expected range—the RTD is defective. Replace
the RTD. Refer to Repair.
MiniBlue II Pneumatic Applicators40
Part 1124393_01 E 2015 Nordson Corporation
RepairRefer to these repair procedures as needed. For repair procedures not included in thissection, refer to the instructions supplied with the replacement part.
Replacing the Plastic Cover (SlimLine Applicators Only)The plastic cover must be removed from the MiniBlue II applicator.1. Disconnect and lock out power to the MiniBlue II SlimLine applicator.2. Allow the applicator to cool down to room temperature.3. Place the side cover insulation into the side covers.4. Insert M3 screws through side cover(s) and insulation.5. Screw the right side cover and insulation onto the applicator to 3-5 in-lbs (.34-.56 NDm).6. Lightly press the module cover into the right side cover.7. Screw the left side cover and insulation onto the applicator to 3-5 in-lbs (.34-.56 NDm).8. Turn power back on to applicator.
1
2
3
4
5
6
4
6
Figure 17: Replacing the plastic cover1. Module2. Right cover3. Left cover
4. Cover insulation5. Module cover6. M3 screw
MiniBluet II Pneumatic Applicators 41
E 2015 Nordson Corporation Part 1124393_01
Replacing a Module1. Relieve system pressure, and then purge the applicator and hose. Refer to the melter and
applicator product manuals for additional information.2. Disable the applicator driver.3. Remove the M4 X 25 module retaining screws, and then remove the module.4. Using a non-abrasive cloth, remove adhesive residue from the face of the applicator body.
CAUTION! Risk of Burns! Applicator body may be hot! Use caution when cleaningit.
5. Insert the two O-rings for each pneumatic port, and the one O-ring for the adhesive port.6. Apply an anti-seize compound (Nordson Corporation PN 900344) to the module retaining
screws, and then install the new module. Tighten the screws to 1.7-2.2 Nm (15-20 in.-lb).
Figure 18: Replacing the module
MiniBlue II Pneumatic Applicators42
Part 1124393_01 E 2015 Nordson Corporation
Replacing a Heater or RTDRTDs are hardwired through the applicator cordset. If an RTD fails, Nordson recommendsthat the entire applicator cordset be replaced. Heaters are terminated inside the manifoldand can be replaced individually without replacing the entire cordset.
The following procedure describes the replacement of an RTD by replacing the entirecordset. Instructions for replacing a heater are also included.
De-energize the system and disable the applicator. Refer to Safety.
Unplug the applicator cordset from the hose.
(Optional) Relieve system hydraulic pressure. Refer to Safety.
(Optional) Using two wrenches, disconnect the hose from the applicator.NOTE: Steps 3 and 4 are not necessary if the applicator is easily accessible and canbe serviced without the need to disconnect the hose.
See Figure 19 or 20 as applicable.1. Remove the applicator cover to access the RTD or heater and remove it from from the
applicator body.2. Disconnect the cordset leads from the terminal block. If the heater is being replaced,
disconnect the heater leads from terminal block.3. Do one of the following:
To Replace the RTDa. Disconnect the ground lead from the manifold and remove the cordset.b. Install a new cordset and insert the RTD in the manifold.c. Reconnect the ground lead to the manifold.
To Replace the Heatera. If necessary, trim the leads of the new heater to match the leads of the old heater.b. Crimp eyelets (P/N 972862) onto the end of the heater.c. Insert the heater into the manifold.d. Insert the heater leads in the terminal block and tighten the terminal block screws.e. Insert the cordset heater leads in the terminal block and tighten the terminal block
screws.4. Reinstall the applicator cover. Refer to Replacing the Plastic Heater Cover (SlimLine
Applicators Only) as needed.5. If the hose was removed earlier, use two wrenches to connect the hose to the applicator.6. Plug the applicator cordset into the hose.7. Restore the system to normal operation.
MiniBluet II Pneumatic Applicators 43
E 2015 Nordson Corporation Part 1124393_01
10
1
2
3
4
5
6
7
8
9
Figure 19: Replacing a heater or RTD on a slim-line applicator1. Mounting bracket2. M3 screw3. Cordset heater leads4. Ground wire5. Terminal block
6. Module7. Heater8. Heater leads9. applicator body
10. RTD
MiniBlue II Pneumatic Applicators44
Part 1124393_01 E 2015 Nordson Corporation
Replacing a Heater or RTD (contd)
12
34
5
67
Figure 20: Replacing a heater or RTD on a single wide or multi module configurableapplicator
1. Cordset heater leads2. Terminal block3. Eyelet4. Heater leads
5. Heater6. RTD7. Ground wire
MiniBluet II Pneumatic Applicators 45
E 2015 Nordson Corporation Part 1124393_01
Replacing a Solenoid Valve1. De-energize the system and disable the applicator. Refer to Safety.2. Unplug the applicator cordset from the hose.3. Relieve system hydraulic pressure. Refer to Safety.4. (Optional) Using two wrenches, disconnect the hose from the applicator.
NOTE: Steps 3 and 4 are not necessary if the applicator is easily accessible and canbe serviced without the need to disconnect the hose.
See Figure 21.
1
2
Figure 21: Replacing a solenoid valve5. Disconnect the solenoid valve cable.6. For IA applicators: remove the two screws and washers (1) from of the applicator, and
then remove the solenoid and tubes.7. For CA or PA applicators: Use two wrenches to remove the tube fittings (2) from the
tubing, and then remove the solenoid.8. Un-thread the tubes or fittings from the solenoid.9. Install the new solenoid valve assembly by reversing step 6.10. Connect the solenoid valve cable.11. Restore the system to normal operation.
MiniBlue II Pneumatic Applicators46
Part 1124393_01 E 2015 Nordson Corporation
This page intentionally left blank.
MiniBluet II Pneumatic Applicators 47
E 2015 Nordson Corporation Part 1124393_01
Using the Illustrated Parts ListsTo order parts, call the Nordson Customer Service Center or your local Nordsonrepresentative. Use these five-column parts lists, and the accompanying illustrations, todescribe and locate parts correctly. The following chart provides guidance for reading theparts lists.
The number in the Part column is the Nordson part number you can use to order thepart. A series of dashes indicates that the part is not saleable. In this case, youmust order either the assembly in which the part is used or a service kit thatincludes the part.
The Description column describes the part and sometimesincludes dimensions or specifications.
The Note column contains letters that refer tonotes at the bottom of the parts list. These notesprovide important information about the part.
Part Description Note
S
S S
NOTE A:B:
NS: Not Shown
MiniBlue II Pneumatic Applicators48
Part 1124393_01 E 2015 Nordson Corporation
SlimLine Single Module Applicator AssemblySee Figure 22.
Item Part Description Qty. Note1 1095703 KIT, REPL, MODULE, MINIBLUE II 12 1051289 HEATER PLUG, WATER RESISTANT 13 371579 O-RING, VITON, 4 X 1 14 ------ HEATER CARTRIDGE, 6MM X 30MM,
230V, 100W1 C
5 1098830 MANIFOLD, SLIMLINE, MINIBLUE II 16 ------ FILTER, APPLICATOR, 100 MESH,
SATURN, M141 D
7 ------ RTD 1 B8 274179 CONNECTOR, HOSE, WITH O-RING,
45 DEGREE1
9 1098834 GASKET 110 1098831 COVER, MINIBLUE II, SLIMLINE 111 733548 INSULATOR, MOUNTING BRACKET 112 1098832 CLAMP, MOUNTING, BOTTOM 113 1098833 CLAMP, MOUNTING, TOP 114 ------ WASHER, M6 115 ------ WASHER, SPRING, 6MM 116 ------ SCREW, SOCKET, M6 X 40 117 ------ SOLENOID 1 A18 ------ SOLENOID MOUNTING TUBE 2 A19 ------ CORDSET 120 ------ SCREW, SOCKET, M4 X 16 221 ------ WASHER, LOCK, M4 222 ------ SCREW, ALLEN HEAD, M3 X 10 123 ------ SCREW, ALLEN HEAD, M3 X 6 124 ------ WASHER, LOCK, M3 125 1103018 PLASTIC COVER SERVICE KIT 126 ------ SCREW, HEX HEAD, M6 X 35 127 375291 O-RING, 6 MM X 1 MM 2NS 939586 CONNECTOR, PORCELAIN, 2STATION 1NS 940081 O RING,VITON, .188X.313X.063, 10408,
MODULE, HYDRAULIC2
NS 940090 O RING,VITON,.208ID X .070W, BR,10409, MODULE
1
NOTE A: Refer to the Solenoid, Tubing and Fittings table provided later in the Parts section.B: Cordsets include RTD. Refer to the Cordsets table provided later in the Parts section.C: Refer to the Heaters table provided later in the Parts section.D: Refer to the Integrated Filters table provided later in the Parts section.
MiniBluet II Pneumatic Applicators 49
E 2015 Nordson Corporation Part 1124393_01
1 2 3
4
5
67
8
14, 15
16
17
18
23
24
19
91011
1213
22
2120
25
25
25
26
27
Figure 22: SlimLine applicator assy.
MiniBlue II Pneumatic Applicators50
Part 1124393_01 E 2015 Nordson Corporation
Single Wide and Multi Module Applicator AssemblySee Figures 23 and 22.
Item Part Description Qty. Note1 1095703 KIT, REPL, MODULE, MINIBLUE II 12 ------ MANIFOLD, MINIBLUE, MULTI-MODULE3 ------ HEATER CARTRIDGE C4 ------ RTD B5 939586 CONNECTOR, PORCELAIN, 2-STATION6 973574 PLUG, O-RING, 9/16-187 ------ GASKET, MINIBLUE, MULTI 1 E8 ------ COVER, MINIBLUE, MULTI, LS, RS 1 E9 ------ PAN HEAD SCREW, M4 X 8 510 ------ FILTER, SATURN, IN-LINE 1 D11 ------ CORDSET 1 B12 ------ ISOLATOR, MOUNTING BRACKET 1 F13 ------ BRACKET, MOUNTING 1 F14 ------ WASHER, M6 215 ------ WASHER, SPRING, 6MM 216 ------ SCREW, SOCKET, M6 X 40 217 ------ SOLENOID 1 A18 ------ TUBE ANS 940081 O RING,VITON, .188X.313X.063, 10408,
MODULE, HYDRAULIC2
NS 940090 O RING,VITON,.208ID X 070W, BR,10409, MODULE
1
NOTE A: Refer to the Solenoid, Tubing and Fittings table provided later in the Parts section.B: Refer to the Cordsets table provided later in the Parts section. Cordsets include RTD.C: Refer to the Heaters table provided later in the Parts section.D: Refer to the Integrated Filters table provided later in the Parts section.E: Refer to Covers and Gaskets provided later in the Parts section.F: Refer to Non SlimLine Mounting provided later in the Parts section
MiniBluet II Pneumatic Applicators 51
E 2015 Nordson Corporation Part 1124393_01
34 5
6
7
8
109
15
1617
2
1
14
13
12
11
18
Figure 23: Multi module applicator assembly independent air
MiniBlue II Pneumatic Applicators52
Part 1124393_01 E 2015 Nordson Corporation
Single Wide and Multi Module Applicator Assembly (contd)
3
45
67
8
10
9
15
16
17
2
1
14
13
12
11
18
Figure 24: Multi module Best Choice replacement applicator assembly continuous air
MiniBluet II Pneumatic Applicators 53
E 2015 Nordson Corporation Part 1124393_01
Replacement ModulesPart Description
1095703 MODULE,MINIBLUE II BALL AND SEAT1121479 MODULE, MINIBLUE II SUREBEAD .20 (.008) PURPLE1121480 MODULE, MINIBLUE II SUREBEAD .31 (.012) GREEN1121481 MODULE, MINIBLUE II SUREBEAD .41 (.016) ORANGE1121482 MODULE, MINIBLUE II SUREBEAD .51 (.020) BEIGE1121483 MODULE, MINIBLUE II SUREBEAD .81 (.032) GOLD1121484 MODULE, MINIBLUE II SUREBEAD 1.0 (.040) TURQUOISE1120093 KIT,MODULE BLANK, MINIBLUE II
CordsetsCordsets include RTDs.
Part Description Note1124023 CORDSET, SLIM, MINIBLUE II A1103014 CORDSET, MINIBLUE II B
1124021 CORDSET, MINIBLUE II, SIDE-MOUNT C
1103908 CORDSET, MINIBLUE II, WATERWASH B
1103015 CORDSET, MINIBLUE II, SLIM, WATERWASH A
1121501 KIT, CORDSET, APPLICATOR, FREEDOM A,B1123116 KIT, CORDSET, APPLICATOR, FREEDOM, WW B
1123115 KIT, CORDSET, APPLICATOR, FREEDOM, WW, SLIM A
NOTE A: Used With Slimline Applicators.B: Used With Standard Applicators, except side-mounted cordsets.C: Used with standard applicators, with side-mounted cordsets.
MiniBlue II Pneumatic Applicators54
Part 1124393_01 E 2015 Nordson Corporation
Solenoid and AccessoriesSolenoids
PartNumber Description Where Used Notes
1095800SINGLE-MODULESOLENOID, SATURNSP (M5 PORTS)
Used for single moduleapplicators andindependent actuationfor multi-moduleapplicators
Nordsonrecommendedsolenoid for standardstitching applications
1124235SINGLE-MODULESOLENOID, SATURNSP, WATERWASH(M5 PORTS)
Used for single moduleapplicators andindependent actuationfor multi-moduleapplicators
Nordson waterwashsolenoidrecommended forstandard stitchingapplications
1123910SINGLE-MODULESOLENOID, P1(M5 PORTS)
Used for single moduleapplicators andindependent actuationfor multi-moduleapplicators.
High Performancesolenoid,recommended forapplications thatdemand the highestlevel of precision andrepeatability
771458SINGLE-MODULESOLENOID, SD MINI(M5 PORTS)
Used for single moduleapplicators andindependent actuationfor multi-moduleapplicators
Recommendedwhere Compactprofile is of thehighest importance
1120826MULTI-MODULESOLENOID, SATURNSP (1/8 IN. NPTPORTS)
Used for common andprogrammed actuation
High flow SP notrecommended forstitching applications
1124238MULTI-MODULESOLENOID, SATURNSPWATERWASH (1/8IN. NPT PORTS)
Used for common andprogrammed actuation
High flow SP forwaterwash, notrecommended forstitching applications
1069020SOLENOID, SATURN,SG, 24 VDC, REV.FUNCTION
Used for common andprogrammed actuation
Available as areplacement only forlegacy applicators
MiniBluet II Pneumatic Applicators 55
E 2015 Nordson Corporation Part 1124393_01
Solenoid CablingPart
Number Description Where Used Notes
1100687CABLE ASSY,SOLENOID, M8,3-WIRE, 5 M
P1 with cable, SD andSP
1100688CABLE ASSY,SOLENOID, 90 DEG,M8, 3-WIRE, 5 M
1100958CABLE ASSY,SOLENOID, M8,3-WIRE, 10 M
1100959CABLE ASSY,SOLENOID, 90 DEG,M8, 3-WIRE, 10 M
1121990 KIT, CABLE, SPLITTERConnects oneextension cable to 2solenoids
1123970CABLE ASSY, P1,SUPPRESSED, 2 PINSOCKET TO M8
Used with P1 onlyLimits current to 2Amaximum. Connectsto STD M8
MiniBlue II Pneumatic Applicators56
Part 1124393_01 E 2015 Nordson Corporation
Solenoid Hard Tubing Replacements KitsPart
Number Description Where Used Kit ContentsIndependent Air Kits
1123003 KIT, SOL TUBING,MB2, M5 X 48
Slim and MBII BCAretrofit applicators withIA
Contains 2 of1098835 and O-rings
1123004 KIT, SOL TUBING,MB2, M5 X 39
MBII Wide applicatorswith IA
Contains 2 of1099274 and O-rings
1123005 KIT, SOL TUBING,MB2, M5 X 75
MBII BCS retrofitapplicators with IA
Contains 2 of1120909 and O-rings
Independent Air Kits
1123672KIT, SOL TUBING,MB2, WIDE W/CA/PASG
Wide body MBIIapplicator with commonor programmed air andSG solenoid
Necessary hardtubing and fittings
1123673KIT, SOL TUBING,MB2, WIDE W/CA/PASP
Wide body MBIIapplicator with commonor programmed air andSP solenoid
Necessary hardtubing and fittings
1123674KIT, SOL TUBING,MB2, BCA/BCSW/CA/PA SP
MBII BCA/BCS retrofitapplicator with commonor programmed air andSP solenoid
Necessary hardtubing and fittings
1123675KIT, SOL TUBING,MB2, BCSW/CA/PA SPSPECIAL
MBII BCS retrofitapplicator (only fits 2module, 22mm pitch,w/LB or RB cordsetposition)
Necessary hardtubing and fittings
Solenoid Optional Flexible Tubing Connection KitsPart
Number Description Where Used Kit Contents
735375 KIT,FLEX TUBING,MB2IA, SP AND SD
IA MBII with SP and SDsolenoids (incl straightand 90 deg fittings)
Straight fittings + 90banjo fittings + shortapplicator inserttubes + tubing +springs
735140KIT, FLEX TUBING,MB2 W/CA/PA SPMULTI AND SG
CA/PA MBII with SP MMand SG solenoids
Pre-assembled, 1/8NPT + tubing+spring
Note: If longer tubing is needed, order by meter, 252277.
MiniBluet II Pneumatic Applicators 57
E 2015 Nordson Corporation Part 1124393_01
Solenoid Accessories and Spare PartsPart
Number Description Where Used Kit Contents
375291 O-RING P1, SP, SP Waterwash,and SD with M5 ports
734262 MUFFLER, M5 SD1100452 MUFFLER, 1/8 IN. NPT,
PLASTIC, COMPACT SP
1058058 MUFFLER, 1/8 IN. NPT,POLYETHYLENE SG
1106321MUFFLERRESTRICTORSERVICE KIT SP
SPUsed when adhesiveviscosity is below700 cps
1082500 MUFFLER, R1/8 SP SPUsed when reducednoise is required(<85 dB)
1106320APPLICATORSOLENOID FIELDWIREABLE M8FEMALE CONNECTOR
SP and SD
1123073KIT, REPLACEMENTELECTRICALCONNECT
SP 10 pieces - SolenoidM8 connectors
1065791 MUFFLER, M7 P17507003 FITTING, M7 X6 TUBE P1
1124325WATERWASHSOLENOIDACCESSORY KIT
SP Waterwash Exhaust relocationhardware
MiniBlue II Pneumatic Applicators58
Part 1124393_01 E 2015 Nordson Corporation
Covers and GasketsCovers and gaskets apply to single wide, multi-module and retrofit applicators. Items mustmeet all of the conditions specified in order to be used on the applicator.
Item Part Description Qty Note7 1098838 GASKET, MINIBLUE MULTI 1 B, C, H8 1098836 COVER, MINIBLUE MULTI, LB, RB 17 1098838 GASKET, MINIBLUE MULTI 1 B, C, G8 1103762 COVER,MINIELITE MULTI, LS, RS 17 1120809 GASKET, MB2/BC, AOSC, SINGLE 2 A, D8 1120661 COVER, MB2/BC, AOSC, SINGLE 27 1120906 GASKET, MB2/BC, AOAC, SINGLE 2 A, E8 1120900 COVER, MB2/BC, AOAC, SINGLE 27 1120907 GASKET, MB2/BC, AOSC, MULTI 2 B, D, H8 1120902 COVER, MB2/BC, AOSC, RB/LB, MULTI I, J7 1120907 GASKET, MB2/BC, AOSC, MULTI 2 B, D, G8 1120903 COVER, MB2/BC, AOSC, RS/LS, MULTI 17 1120908 GASKET, MB2/BC, AOAC, MULTI 2 B, E, H8 1120904 COVER, MB2/BC, AOAC, RB/LB, MULTI I, J7 1120908 GASKET, MB2/BC, AOAC, MULTI 2 B, E, G8 1120905 COVER, MB2/BC, AOAC, RS/LS, MULTI 1
NOTE A: Used on Single Module ApplicatorsB: Used on Multi-Module ApplicatorsC: Used on "000" Manifold StyleD: Used on Expansion Spring-Close Manifold StyleE: Used on Expansion Air Close Manifold StyleF: Used For Water Wash ApplicationsG: Used For "LS or RS" Cordset LocationsH: Used For "LB or RB" Cordset LocationsI: If Cordset Position is "LS or RS" then Quantity is 1J: If Cordset Position is "LB or RB" then Quantity is 2
MiniBluet II Pneumatic Applicators 59
E 2015 Nordson Corporation Part 1124393_01
Non SlimLine MountingItem Part Description Qty Note
12 272400 INSULATOR, MOUNT 1 A13 326508 KIT, BRACKET, APPLICATOR
MOUNTING, KBCGS 1
14 WASHER, FLT, M, NARROW, M8, STL,ZN 2
15 WASHER, LK, M, SPT, M8, STL, ZN 216 SCR, HEX, CAP, M8X45, BL 116 SCR, HEX, CAP, M8X25, BL 112 733539 ISOLATOR, 3MM, MINIBLUE B, C, D13 1026940 BRACKET E, F, G14 WASHER, FLT, M, REG, M6, STL, ZN15 WASHER, LK, M, SPT, M6, STL, ZN16 SCR, SKT, M6X40, ZN
NOTE A: Only Used on Single Module Applicators with Expansion Air Close ManifoldStyle
B: If Manifold Length is < 150mm then Quantity is 1C: If Manifold Length is > 150mm and < 300 then Quantity is 2D: If Manifold Length is > 300 then Quantity is 3E: If Manifold Length is < 150mm then Quantity is 2F: If Manifold Length is > 150mm and < 300 then Quantity is 4G: If Manifold Length is > 300 then Quantity is 6
MiniBlue II Pneumatic Applicators60
Part 1124393_01 E 2015 Nordson Corporation
Hose Connectors and Filter AssembliesRefer to Table 8 to select the appropriate filter mesh size based on the orifice diameter of thenozzle being used. Refer to Table 9 for Saturn filter part numbers.
Figure 25: Saturn in-line filter and integrated filter
Table 8 Recommended Filter Mesh SizeIf the Nozzle Orifice Diameter is... ...use a filter with a...
50 Mesh (.30 mm) Screen(Red ring)
100 Mesh (.15 mm)Screen (Gold ring)
200 Mesh (.07 mm)Screen (Purple ring)
MiniBluet II Pneumatic Applicators 61
E 2015 Nordson Corporation Part 1124393_01
Table 9 Saturn In-line Filters and Filter ElementsDescription Part
NO FITTING, 50 MESH 1120049NO FITTING, 100 MESH 1120050NO FITTING, 200 MESH 1120051STRAIGHT FILTER, 0.30 MM (0.0156 IN.), 50 MESH 1007033STRAIGHT FILTER, 0.15 MM (0.0059 IN.), 100 MESH 1007034STRAIGHT FILTER, 0.07 MM (0.0029 IN.), 200 MESH 100703590_ FILTER, 0.30 MM (0.0156 IN., 50 MESH 100723090_ FILTER, 0.15 MM (0.0059 IN.), 100 MESH 100723190_ FILTER, 0.7 MM (0.0029 IN.), 200 MESH 100723245_ FILTER, 0.30 MM (0.0156 IN.), 50 MESH 100723345_ FILTER, 0.15 MM (0.0059 IN.), 100 MESH 100723445_ FILTER, 0.07 MM (0.0029 IN.), 200 MESH 1007235
Filter KitsReplacement parts for the Saturn In-line filter.
Description 2-PieceKit Part Number
5-PieceKit Part Number
KIT, FILTER, 50 MESH, SATURN IN-LINE 1007372 1007036KIT, FILTER, 100 MESH, SATURNIN-LINE
1007373 1007037
KIT, FILTER, 200 MESH, SATURNIN-LINE
1007374 1007038
Replacement parts for the Saturn M14 Integrated applicator filter.Description 2-Piece
Kit Part Number5-Piece
Kit Part NumberKIT, FILTER, 50 MESH, SATURNINTEGRATED
1045502 1123661
KIT, FILTER, 100 MESH, SATURNINTEGRATED
1045506 1123662
KIT, FILTER, 200 MESH, SATURNINTEGRATED
1045520 1123663
MiniBlue II Pneumatic Applicators62
Part 1124393_01 E 2015 Nordson Corporation
Applicator-to-Hose ConnectorsSee Figure 26. applicator-to-hose connectors are installed between the applicator and hoseto ease hose routing and to help prevent bending or pinching of the hose.
2 31
4
Figure 26: Applicator-to-hose fittingsItem Part Description Note
1 972657 CONNECTOR, HOSE, WITHO-RING, STRAIGHT
A
2 274179 CONNECTOR, HOSE, WITHO-RING, 45_
3 274180 CONNECTOR, HOSE, WITHO-RING, 90_
4 945032 S O-RING, VITON, 3/8 IN. TUBE BNOTE A: All applicators are shipped with this straight hose connector pre-installed on the
applicator.B: This is the replacement O-ring for all hose connectors.
Insulating CuffsInsulating cuffs are used to insulate hose-to-applicator joints.
Part Description273634 CUFF, INSULATING, 64 MM (2.5 IN.)273635 CUFF, INSULATING, 50 MM (2.0 IN.)274429 CUFF, INSULATING, 44 MM (1.75 IN.)
MiniBluet II Pneumatic Applicators 63
E 2015 Nordson Corporation Part 1124393_01
Standard Saturn NozzlesSaturn precision nozzles have patented color-coded rings that provide easy identification ofnozzle orifice size. Refer to the Adhesives and Sealants Equipment Guide for a full listing ofavailable Saturn nozzles.
Engagement Length RingOrifice Diameter Ring
Orifice Diameterand Bottom RingColor mm (in.)
Engagement Length and Top Ring Color mm (in.)1.3 (.050)Purple
1.9 (.075)Brown
2.5 (.100)Blue
3.8 (.150)Green
7.6 (.300)Black
.20 (.008) Purple 322008.25 (.010) Blue 322010.31 (.012) Green 322012 322112 322212 322312 322412.36 (.014) Yellow 322014 322114 322314 322414.41 (.016) Orange 322016 322116 322216 322416.46 (.018) Red 322018 322118 332318 322418.51 (.020) Beige 322020 322120.53 (.021) Brown 322421.61 (.024) Gray 322424.71 (.028) Black 322428
MiniBlue II Pneumatic Applicators64
Part 1124393_01 E 2015 Nordson Corporation
MiniBlue II Sure Bead NozzlesPart Description
1121473 KIT, NOZZLE, .008 (PURPLE)1121474 KIT, NOZZLE, .012 (GREEN)1121475 KIT, NOZZLE, .016 (ORANGE)1121476 KIT, NOZZLE, .020 (BEIGE)1121477 KIT, NOZZLE, .032 (GOLD)1121478 KIT, NOZZLE, .040 (TURQUOISE)
HeatersSlimLine Applicator
240 VAC Cartridge 200 VAC Cartridge6mm Diameter Heater P/N Heater
Wattage6mm Diameter Heater
P/NHeaterWattage
734013 109 1061561 100
MiniBluet II Pneumatic Applicators 65
E 2015 Nordson Corporation Part 1124393_01
Standard MiniBlue II ApplicatorMinimumApplicator
Body Length(mm)
MaximumApplicator
Body Length(mm)
240 VAC Cartridge 200 VAC Cartridge⅜ in.
DiameterHeater P/N
HeaterWattage
⅜ in.DiameterHeater P/N
HeaterWattage
40.0 52.9 938123 150 1070406 15053.0 64.9 448841 200 1070401 20065.0 75.9 250682 200 1070291 20076.0 83.9 121662 250 1070294 25084.0 94.9 139311 250 1070296 25095.0 109.9 109387 250 1070293 250110.0 118.9 938126 280 1070407 280119.0 128.9 109327 300 1070292 300129.0 140.9 710669 327 1070400 300141.0 153.9 702409 300 1070299 300154.0 172.9 149294 350 1070297 350173.0 179.9 938127 380 1072628 380180.0 198.9 135817 476 1070295 400199.0 221.9 938132 440 1072629 440222.0 242.9 860879 500 1070402 500243.0 267.9 149299 550 1070298 550268.0 290.9 938077 600 1070405 600291.0 305.0 938067 600 1070404 600
Retro-Fit MiniBlue II ApplicatorMinimumApplicator
Body Length(mm)
MaximumApplicator
Body Length(mm)
240 VAC Cartridge 200 VAC Cartridge½ in./13mmDiameterHeater P/N
HeaterWattage
½ in./13mmDiameterHeater P/N
HeaterWattage
44.0 58.2 1054662 200 1054628 20058.3 69.4 1054663 200 1054629 20069.5 77.2 1054664 250 1054630 25077.3 88.2 1054672 250 1054633 25088.3 102.6 1054673 250 1054634 250102.7 112.3 1054675 280 1054635 280112.4 121.7 1054676 300 1054637 300121.8 134.5 1055575 300 1054638 300134.6 147.5 1055576 300 1054639 300147.6 166.9 1054677 350 1054640 350167.0 173.4 1054678 380 1054642 380173.5 192.8 1054659 400 1054644 400192.9 216.9 1054681 440 1054647 440217.0 238.2 1054683 500 1054650 500283.3 264.1 1054685 550 1054652 550264.2 286.9 1054688 600 1054655 600287.0 305.0 1054689 600 1054656 600
MiniBlue II Pneumatic Applicators66
Part 1124393_01 E 2015 Nordson Corporation
Thermal Insulating Applicator CoversPart Description
1099297 COVER, FLEXIBLE, SLIMLINE1099298 COVER, FLEXIBLE, SINGLE MODULE, WIDE1103018 PLASTIC COVER KIT, SINGLE MODULE SLIM1120818 COVER, FLEXIBLE, SINGLE MODULE, WIDE, BEST CHOICE SPRING
CLOSED RETRO-FIT1121065 COVER, FLEXIBLE, SINGLE MODULE, WIDE, BEST CHOICE AIR
CLOSED RETRO-FIT
Extension CablesExtension cables are used when a applicator has two cordsets and only one hose will beused.
Part Description108946 CABLE, EXTENSION, APPLICATOR TO MELTER, 4.9 M (16 FT)728023 CABLE, EXTENSION, WATER-WASH APPLICATOR TO MELTER,
5.5 M (18 FT)728093 CABLE, EXTENSION, WATER-WASH, 6.1 M (20 FT)124992 CABLE, EXTENSION, APPLICATOR TO BULK MELTER, 4.3 M
(14 FT)
MiniBluet II Pneumatic Applicators 67
E 2015 Nordson Corporation Part 1124393_01
Maintenance AccessoriesPart Description
132426 DIAGNOSTIC DEVICE W/CABLE ASSY (hose/applicator)1108372 LUBRICANT, O-RING, 4 OZ (FOR LUBRICATING O-RINGS)1108371 LUBRICANT, NEVER-SEEZ, 8 OZ CAN1120201 NEVER-SEEZ, 1 OZ900290 NEAT'S FOOT OIL901915 NOZZLE CLEANING KIT331871 NUTDRIVER,5/32 (Tool, removal/installation, integrated
right-angle module nozzles)231262 KIT, QUICK-DISCONNECT FITTING, 1/4 NPT (solenoids)270755 TYPE R FLUID, 1.0 GAL902514 GLOVES,SAFETY (Protective gloves)
SpecificationsParameter Specification
Operating temperature 204 _C (400 _F) maximumOperating air pressure(1) 3.4-5.5 bar (50-80 psi)Working hydraulic pressure 103 bar (1500 psi) maximumSolenoid valves Nordson 24 VDC high temperature,
factory installedElectrical service 240 VAC, 50/60 Hz; 200 VAC, 50/60 Hz
optional(1) Recommended range. Dry, regulated non-lubricated air required for consistent applicatoroperation.
MiniBlue II Pneumatic Applicators68
Part 1124393_01 E 2015 Nordson Corporation
DimensionsDimension drawings can be found on the emanuals.nordson.com website.
MiniBlue™ II Pneumatic Applicators 69
Part 1124393_01E 2015 Nordson Corporation
MiniB
lueIIA
pplic
ator
Configu
ratio
nCod
eTo
deter
mine
theco
nfigu
ration
ofaa
pplicato
r,obta
inits
confi
gurat
ionco
dean
drefe
rtoTa
ble10
.Ta
ble10
Expla
natio
nofA
pplicato
rCon
figura
tionC
odeP
ositio
nsCo
dePo
sition
Desc
riptio
nCo
deVa
lue
MB2BEL
ACA
TTS
E4
1000
00SP
}
}
}
}
}
}
}
}
}
}
}
12
34
56
78
910
11
Confi
gurat
ionCo
de
000}
12
1Ap
plica
tormo
del
MiniB
lueII
2Mo
duletyp
eBE
L=Mi
niBlue
IIball
ands
eat
020=
.020S
urebe
adori
ficen
ozzle
008=
.008S
urebe
adori
ficen
ozzle
032=
.032S
urebe
adori
ficen
ozzle
012=
.012S
urebe
adori
ficen
ozzle
040=
.040S
urebe
adori
ficen
ozzle
016=
.016S
urebe
adori
ficen
ozzle
3Nu
mber
ofmo
dules
1-8,0
0=Sli
mline
,allo
thers
wide
modu
lesNOTE:A
llSlim
linea
pplicato
rswillc
omew
ithpla
sticc
overs
instal
led.
4Vo
ltage
A=2
40V
B=2
00V
5Air
supp
lyco
nfigu
ration
CA=c
ommo
nair
IA=i
ndep
ende
ntair
PA=p
rogram
meda
ir6
Cordse
ttype
T=30
00/Blue
Serie
sF=
Free
dom
Serie
scord
set
W=W
aterw
ash
D=F
reedo
mSe
riesw
aterw
ashc
ordse
tCo
ntinu
ed...
70 MiniBlue™ II Pneumatic Applicators
Part 1124393_01 E 2015 Nordson Corporation
Code
Posit
ionDe
scrip
tion
Code
Value
s
7Co
rdse
tpos
ition
TS=T
opSid
eLS
=Left
Side
RS=R
ightS
ideLB
=Left
Back
RB=R
ightB
ack
8So
lenoid
SP=S
aturn
Platin
umSD
=MiniMa
cP1
=P1
NOTE:T
heSG
solen
oidisav
ailab
leon
lyfor
legac
yapp
licato
rs.9
Hose
conn
ector
angle
andm
eshs
izeE0
=50-me
shstr
aight
E4=5
0-me
sh45
-deg
reeE9
=50-me
sh90
-deg
reeF0
=100
-mes
hstra
ight
F4=1
00-m
esh4
5-deg
reeF9
=100
-mes
h90-d
egree
G0=2
00me
shstr
aight
G4=2
00me
sh45
-deg
reeG9
=200
mesh
90-deg
ree10
Numb
erof
hydrau
licpo
rts1 3 5
11Co
ver
000=
NoCo
ver
010=
SoftC
over
12Ma
nifold
style
000=
Stan
dard
MiniB
lueBC
A=M
ounts
insa
meloc
ation
asaB
estC
hoice
Air-C
losea
pplicato
rBC
S=M
ounts
insa
meloc
ation
asaB
estC
hoice
Sprin
g-Clos
eapp
licato
r