MicroMAX-SOC Setup via Netspan

Property of Airspan Networks Inc. All Rights Reserved

MicroMAX-SOC Setup via Netspan

Setup via Netspan Property of Airspan Networks Inc. All Rights Reserved

Contents

Introduction .................................................................................................................................. - 4 - Initial MicroMAX-SOC Connection ............................................................................................. - 5 - MicroMAX-SOC Automatic Discovery by Netspan...................................................................... - 9 - Preparing Service Profiles ......................................................................................................... - 16 - Provisioning Service for Subscriber Station .............................................................................. - 25 -

- 3 - Introduction


This page is intentionally left blank

- 4 -


Introduction This document provides setup steps for using the MicroMAX-SOC via Netspan. To avoid or minimize potential service interruption, please ensure that you have read and understood the contents of this document.

The setup procedure will be defined as follows

Initial MicroMAX-SOC Connection Connecting via Netspan Subscriber Configuration via Netspan Final Subscriber Configuration

- 5 - Initial MicroMAX-SOC Connection


Initial MicroMAX-SOC Connection The following are the steps to the BS via the WEB.

Ensure that your Web browser with which you want to access the Web-based Management is running Netscape Communicator 4.03 or higher, or Microsoft Internet Explorer 4.01 or higher. In addition, before you can access the WBM tool, you need to ensure that your Web browser's settings enable access to Web-management tools such as the WBM. To connect to the MicroMAX-SOC via the WEB 1. Connect to the SOC BSR using WEB (10.0.0.123 default IP address)

2. Go to IP configuration and modify the IP address according to your network

3. Click Submit The following is displayed

4. Go to SNMP Communities and modify the parameters according to network (if required)

5. Click Submit The following is displayed

- 6 -


6. Navigate to Advanced > setMacUl and set UL frequency in HZ

(other parameters can be left on the defaults i.e. not configured)

7. Click Call As shown below

- 7 - Initial MicroMAX-SOC Connection


8. Wait until the OK confirmation appears (under the Call button) 9. Go to Advanced > setMacDL and set:

a. UL frequency in HZ

b. TX power in dbm

c. BS ID (example = 11:22:33:44:55:66)

Note: Defining other parameters is not mandatory.

10. Click Call

11. Wait until the OK confirmation appears (under the Call button)

- 8 -


12. Navigate back to Home

13. Perform Reboot and confirm 14. MicroMAX-SOC BS will reboot with the new setting in approximately 60 seconds

The MicroMAX-SOC is now ready to be connected via Netspan

- 9 - MicroMAX-SOC Automatic Discovery by Netspan


MicroMAX-SOC Automatic Discovery by Netspan The following are the steps for automatic discovery of MicroMAX-SOC via Netspan. To connect to the MicroMAX-SOC via Netspan 1. Login to Netspan

2. Navigate to Server > Discovery Parameters The following is displayed

3. Click Add 4. Define:

a. Name

b. Write Community

Note: This should be same as was configured before on the BS

c. Read Only Community define a Community then click Add (on right side of the field)

d. Port enter 161 then click Add (on right side of the field) As shown below

- 10 -


5. Click Add in the Discovery Target IP Address Ranges section this will create range.

For example Start address = 0.0.0.0 and End Address=0.0.0.0

6. Select within the values area to set (define) both to the required IP address (of the BS)

7. Click OK As shown below



The following is displayed after OK has been clicked: The Management panel of the BS for which the Discovery task was created

8. Navigate to Configuration Management and then Base Station (in the left-hand

column)

- 12 -


9. Select the BS that Netspan discovered

10. Double-click on the specific BSR row

11. Double-click on the BS and select the Sector tab

As shown below:



12. Double-click on the Sector row (of the specific BS) and select the Configuration tab

13. Click Update from BS (lower right hand section of the window) As shown below:

- 14 -


14. Check Allow Edit and select (change) Licensed on the Licensed Band dialog

(dropdown list) As shown below:



15. Confirm that the Frequency setting and the TX power are correct

16. Click Apply Your SOC is now discovered by Netspan and is ready for Subscriber configuration.

- 16 -


Preparing Service Profiles The following are the steps to preparing service profiles. To prepare service profiles 1. Navigate to Service Profiles and then SS Custom Configuration (in the left-hand

column)

2. Edit Subscriber Station Custom Configuration Profile for the Subscribers (Name, Services Settings, Modulation Setting)

Note: VLAN tagging is not mandatory as it is not supported

3. Click OK As shown below:

4. Navigate to Service Profiles and then Service Class (in the left-hand column)

5. Click Add 6. Set the following parameters

As shown below:

- 17 - Preparing Service Profiles


7. Set the following parameters

As shown below:

- 18 -


8. Click OK

9. Navigate back to Service Profiles and then VLAN Configuration (in the left-hand column)

10. Click Add 11. Create the following configuration

As shown below:

12. Click OK

13. Navigate back to Service Profiles and then Packet Classifier (in the left-hand column)

14. Click Add

15. Set Name and Priority As shown below:



16. Click OK

17. Navigate to Service Profiles and then Service Class (in the left-hand column)

18. Click Add 19. Create the following

As shown below:

- 20 -


20. Set the following parameters

As shown below:



21. Navigate back to Service Profiles and then Service Product (in the left-hand column)

22. Click Add

23. Set Name

24. Click Add

25. Select Service Class from dialog (dropdown list)

26. Select Download As shown below:

27. Click Add in the Service Flow Template Classifiers

28. Click OK As shown below:

- 22 -


29. Click Add

30. Select Service Class from dialog (dropdown list)

31. Select Upload As shown below:



32. Click OK

The following is displayed:

- 24 -


33. Click OK Subscribers are now ready to connect.

- 25 - Provisioning Service for Subscriber Station


Provisioning Service for Subscriber Station After the Subscriber is booted up it will scan for the BS and connect to it. The only thing that is required it to add this Subscriber to the Netspan database. This can be performed either by adding it manually or after it is connected to BS.

The following describes configuration via BS. To add a Subscriber to the Netspan dB via the BS 1. Start the SS and verify connection, wait for 30 seconds

2. Navigate to Configuration Manager and then to Base Station 3. Select the BS

4. Double-click on the specific BS and select the Configuration tab As shown below:

5. Double-click on the specific BS and select the Sectors tab

As shown below:

- 26 -


6. Select the Registered SSs tab

7. Double-click on the specific SS

8. Click Edit

9. Select Service Product from dialog (dropdown list) in the Service pane (section)

10. Select Config Profile from dialog (dropdown list) in the Service pane (section)

11. Set Services to Enabled (select Yes)

12. Click Add in the VLAN pane (section) As shown below:

- 27 - Provisioning Service for Subscriber Station


13. Click OK

14. Click Close

- 28 -


Settings are now complete

- 29 -


This page is intentionally left blank

IntroductionInitial MicroMAX-SOC ConnectionMicroMAX-SOC Automatic Discovery by NetspanPreparing Service ProfilesProvisioning Service for Subscriber Station

MicroMAX-SOC Setup via Netspan

Documents

Transcript of MicroMAX-SOC Setup via Netspan