MICRO IRRIGATION SYSTEM - d3pcsg2wjq9izr.cloudfront.net€¦ · MICRO IRRIGATION SYSTEMS DRIP LINE...
Transcript of MICRO IRRIGATION SYSTEM - d3pcsg2wjq9izr.cloudfront.net€¦ · MICRO IRRIGATION SYSTEMS DRIP LINE...
MICRO IRRIGATION SYSTEM IDEAL FOR HORTICULTURE, FLORICULTURE AND ARBORICULTURE, GREENHOUSE AND OPEN FIELDS
DRIP LINE WITH FLAT EMITTER
MEGAMICRO
AQUADROP® is a drip line with fl at dripper designed for open fi eld irrigation or greenhouse. It is ideal for vegetable crops such as watermelons, melons, strawberries, zucchini, peppers, eggplants, potatoes, cucumbers, onions, etc.., and fl ower crops like gerbera, roses, carnations, etc.The new and innovative dripper has been designed with a dual protection system to ensure a high resistance to clogging. The active system locks the particles suspended into water, while the turbulent fl ux reduces the accumulation of deposits within the dripper labyrinth.
· Irrigation of surface crops or slightly covered cultivations. · Easy installation and low maintenance cost.· Excellent emission uniformity over long distances.· Endurance to clogging.· Internal fi lters prevent particles intrusion into the dripper.· Blue stripe to indicate correct laying up on the ground.· Endurance to UV rays.· Warranty: 1 to 5 years depending on the thickness.
° D/16 mm spacing 15 cm: 6 mil = 2800 m - 7 mil = 2500 m - 8 mil = 2200 m - 10 mil = 2000 m° D/22 mm spacing 15 cm: 7 mil = 2000 m - 8 mil = 1500 m - 10 mil = 1300 m - 12 mil = 1000 m* Recommended fi ltration for 1,1 l/h: 150 mesh – 100 micron
MICRO Test carried out on 10 mil (0.25 mm) thickness with water at 20° C MEGA Tests carried out on 25 mil (0.62 mm) thickness with water at 20° C
TECHNICAL FEATURES
SPECIFICATIONS
MICRO MEGANominal diameter 16 - 22 - 29 mm
Thickness 6 mil0,15 mm
7 mil0,18 mm
8 mil0,20 mm
10 mil0,25 mm
12 mil0,30 mm
15 mil0,38 mm
18 mil0,45 mm
25 mil0,62 mm
Max work pressure D/16 mm 0,80 bar 0,90 bar 1,00 bar 1,20 bar 1,40 bar 1,60 bar 1,80 bar 2,00 bar
Max work pressure D/22 mm - 0,80 bar 0,90 bar 1,10 bar 1,30 bar 1,50 bar 1,70 bar 1,90 bar
Max work pressure D/29 mm - - - 0,90 bar 1,10 bar - - -
Nominal Flow rate (1,0 bar) 1,10* - 1,30 - 1,60 - 2,10 - 4,50 l/h 1,30 - 2,20 l/h
Dripper spacing 15 - 100 cm
Reel Length D/16 mm ° 3000 m 2700 m 2500 m 2200 m 1700 m 1200 m 1000 m 900 m
Reel Length D/22 mm ° - 2100 m 1800 m 1500 m 1200 m 900 m 800 m 600 m
Reel Length D/29 mm - - - 1200 m 1000 m - - -
Recommended fi ltration 120 mesh - 130 micron
PRESSURE - FLOW RATE RATIO
Pressurebar
Nominal fl ow rate l/h
1,10 1,30 1,60 2,10 4,50 1,30 2,20
0,50 0,60 0,86 1,00 1,40 2,80 0,80 1,15
0,60 0,70 0,96 1,15 1,50 3,30 0,90 1,60
0,70 0,80 1,05 1,30 1,70 3,60 1,00 1,80
0,80 0,90 1,15 1,45 1,80 3,90 1,10 2,00
0,90 1,00 1,23 1,55 1,90 4,20 1,20 2,10
1,00 1,15 1,35 1,65 2,15 4,50 1,30 2,20
1,20 1,25 1,50 1,90 2,40 4,80 1,50 2,40
1,40 - - - - - 1,70 2,60
1,60 - - - - - 1,90 2,80
1,80 - - - - - 2,05 3,00
2,00 - - - - - 2,15 3,20
MICRO MEGA
* EU = 90% - Data reported on fl at grounds. Work pressure 1,00 bar
RECOMMENDED LATERAL LENGTH RELATED TO EMISSION UNIFORMITY (m)* FLOW RATE VARIATIONS
MICRO
Diam.mm
Nominalfl ow rate
l/h
Spacing cm
20 30 40 50 60
16
1,10 145 187 227 261 292
1,30 130 167 202 233 261
1,60 105 137 165 190 210
2,10 98 126 153 176 197
4,50 62 79 96 111 124
22
1,10 264 340 411 474 530
1,30 213 274 332 382 427
1,60 170 220 265 307 340
2,10 158 203 246 283 317
4,50 99 128 155 178 200
29
1,10 383 503 617 720 816
1,30 309 406 498 581 658
1,60 276 363 444 518 588
2,10 229 300 369 430 488
4,50 144 189 233 271 308
5,00MICRO
4,00
3,00
2,00
1,00
0,50 0,70 0,90 1,10 1,30
MEGA
MEGA
Diam.mm
Nominalfl ow rate
l/h
Spacing cm
20 30 40 50 60
161,30 127 164 198 228 256
2,20 80 103 125 144 162
221,30 211 272 329 377 424
2,20 150 193 234 269 301
291,30 303 345 422 492 559
2,20 218 285 351 409 464
4,50 l/h
2,10 l/h
1,30 l/h
1,10 l/h
1,30 l/h
1,60 l/h
2,20 l/h
Flow
rate
l/h
Flow
rate
l/h
Pressure bar
Pressure bar
0,40
1,00
1,50
2,00
2,50
3,00
3,50
0,60 0,80 1,00 1,20 1,40 1,60 2,00
MICRO IRRIGATION SYSTEMS
DRIP LINE WITH FLAT EMITTER DRIP LINE WITH CYLINDRICAL EMITTER DRIP TAPE
Viale Aldo Moro, 31 . 70043 Monopoli, BA . ItalyTel. +39 080 802122 . Fax +39 080 802567
www.plasticpuglia.it
FITTINGS AND VALVES