MICE magnet positional tolerances when assembling the cooling channel
description
Transcript of MICE magnet positional tolerances when assembling the cooling channel
![Page 1: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/1.jpg)
MICE magnet positional tolerances when assembling the cooling channel
1
Tim HaylerSTFC
![Page 2: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/2.jpg)
MICE NOTES
• 229 Alignment Errors on Emittance Measurements for MICEDavid Forrest, F.J.P. Soler deals with spectrometer alignment (step VI, flip, 200 MeV/c) - gives tolerance of order 10 mm, 3 mrad
• 202 Beamline to MICE Alignment and Matching ToleranceC. Rogers deals with beam alignment to cooling channel (step VI flip 200 MeV/c - gives tolerance of order 2 mm, 10 mrad
• 64 Initial study of MICE Magnet Alignment RequirementsU. Braver, J.H. Cobbdeals with focus coil alignment (step VI, flip, 200 MeV/c) - gives tolerance of order 2 mm, 2 mrad
Thanks to Chris Rogers and John Cobb for the information
2
![Page 3: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/3.jpg)
ConclusionDifferent studies, all agreeing with a general tolerance of 1 mm, 1 mrad? Does this tolerance simply cover our backs?
Can we relax these tolerances for the cooling channel?seems the order of importance is: Tilt angle very importantTransverse not so importantLongitudinal less stringent again
Can we split up the tolerance into these three components?
3
![Page 4: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/4.jpg)
MICE Hall CSYS
x
y
z
4
![Page 5: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/5.jpg)
The position of the magnetic axis with respect to a tolerance zone about the nominal axis
Magnetic axis of the module
Cylindrical tolerance zone of 1mm diameter1mm
Y
ZX
Reference the MICE hall coordinate system on slide four
Beam Nominal axis
Projection 5
![Page 6: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/6.jpg)
The positional tolerance of the magnet centre longitudinally with respect to the nominal centre
X
Y
Z
y
xz
Reference the MICE hall coordinate system on slide four
Nominal centre
Magnet centre
Upstream Downstream
6
±0.5mm
![Page 7: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/7.jpg)
Table of positional tolerances
Component Positional tolerance zone of the magnetic axis with respect to the nominal axis
The positional tolerance of the magnet centre longitudinally with respect to the nominal centre
Comments
Virostek plates 5mm ±3mm
Spectrometer Solenoid
1mm ±0.5mm
AFC 1mm ±0.5mm
RFCC 1mm ±0.5mm
7
Potential to relax and split the tolerance zone into tilt and traverse tolerances?
![Page 8: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/8.jpg)
Spectrometer support frame
8
![Page 9: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/9.jpg)
Spectrometer feet locations
The Spectrometer has four feet, in each foot there is a boss that houses a locating pin. The locating pin is threaded into the boss and can be adjusted in height about its nominal position. A hemispherical dome on the end of the pin locates in a similar hemispherical cup on the support frames.
1250
2160
Spectrometer foot
![Page 10: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/10.jpg)
Height adjustment
10
![Page 11: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/11.jpg)
Longitudinal adjustment
11
![Page 12: MICE magnet positional tolerances when assembling the cooling channel](https://reader036.fdocuments.in/reader036/viewer/2022062806/56814ef7550346895dbc86c8/html5/thumbnails/12.jpg)
Traverse adjustment
12