Mibet (Xiamen) New Energy Co., Ltd. MRac Tile Roof...

Mibet (Xiamen) New Energy Co., Ltd.

No 69, Xintian Rd., Jimei District, Tel: +86 592 3754999

Xiamen, China 361022 Fax: +86 592 6771575

www.mbt-energy.com Email: [email protected] 1

MRac Tile Roof Installation Guide

Tile Interface 117HA

AS/NZS1170.2

Content

1. Product Introduction-------------------------------------------------------P2

2. Installation Tools& Components---------------------------------------P3

3. Installation Guide----------------------------------------------------------P5

4. Warranty--------------------------------------------------------------------P10



Xiamen, China 361022 Fax: +86 592 6771575


1. Product Introduction

MRac Tile Interface 117HA tile roof mounting system is specially developed for

the maximum flexibility in designing for both residential and commercial rooftop

solar system. Using our patented components, the panels can be freely

installed on almost all even and sloping surfaces, no matter what tile material it

is. The system is also impressive coz of its top-quality material, high

compatibility and overall concept.

Please read this Installation Guide thoroughly before installing the MRac

RoofOn system. This Guide offers the planning and installation instruction for

MRac RoofOn solution.

MRac RoofOn products, when installed in accordance with this guide, will be

structurally adequate and will meet the local standards. During installation,

especially when working on the roof, be sure to observe the appropriate safety

regulations and please pay attention to the relevant regulations of your local

region. Please check that you are using the current version of the installation

manual by contact Mibet Energy by mail on [email protected], or your

local representative.

The installer is solely responsible for:

Complying with all applicable local or national building codes, including any that may

supersede this manual;

Ensuring that MRac and other products are appropriate for the particular installation

and the installation environment;

Using only MRac parts and installers-supplied parted as specified by MRac

(Substitution of parts may void the warranty and invalidate the letter of certification on

page 2);

How to recycle: According to the local relative statute;

How to disassemble: Countermove with installation;

Ensure that there are no less than two professional workers in panel installation;

Ensure the installation of relative electrical equipment is performance by professional

electrician.

Ensure safe installation of all electrical aspects of the PV array.

mailto:[email protected]



Xiamen, China 361022 Fax: +86 592 6771575


2. Installation Tools & Components

2.1 Installation Tools

6mm Inner hexagon spanner;

Electrical tool（Fasten M6 outer hexagon self-drilling screws and cross

recessed pan head screws）;

9, 10, 17, 19 mm open spanner (Fasten bolts on End Clamps and Inner

Clamps);

Angle grinder;

Electrical wire;

Small pieces of wood (in case interfaces are not on a line coz of beam

situation.)

2.2 Components

Components

Standard Rail

Standard Rail Connector

Inter Clamp Kit

End Clamp Kit

Tile Interface 117HA


No 53, Baihuyan Rd., Jimei District, Tel: +86 592 6771595

Xiamen, China 361022 Fax: +86 592 6771575


2.3 Solution Overview

a. Standard Rail

b. Inter Clamp Kit

c. Interface

d. Standard Rail

Connector

e. End Clamp Kit

2.4 Planning installation Area

1) Panel qty in MD x Panel length (Please check it with Installation Guide

from panel manufacturer as well)

2) Panel qty in TD x(Panel width +18mm)+32mm.

3) Spacing between interfaces can as wide as 2.0m in TD

4) Spacing between interfaces in MD= around 1/2 or 3/4 of panel length

5) Spacing between panels:17 mm

(Note:

Spacing between panels should be adjusted smaller when system is

exposure in wind, placed on edge or in the corner of the rooftop.

MD: Machine Direction; TD: Transverse Direction)

c d e

a b



Xiamen, China 361022 Fax: +86 592 6771575


3. Installation Guide

3.1 Installation of Tile Interface 117HA

3.1.2 Install the

interface onto the

wooden beam by

three M6*80

screws.

3.1.3 The interface

is not allowed to

press on the tile,

using small piece of

wood to lift the

height of interface if

necessary.

3.1.4 Get rid of the

small part of tiles

where you find the

interface is difficult

to lie down on the

bottom tiles flatly,

using Angle Grinder

or hammer. This

step is still

necessary if the

system is installed

on curved tile.

CAUTION: It was

forbidden taking the

interfaces as

ladder, this may

destroy the tiles.



Xiamen, China 361022 Fax: +86 592 6771575


3.1.5 When

installed on flat tile

rooftop, cut off one

corner where the

interface need to be

installed.

3.1.6 Cut one piece

of Titanium zinc

plate for the corner

area, put it under

the interface and

make sure 20mm

surrounding area

need to be covered

by this plate.

(Note: See photos

in right.)

3.1.7 Installation of

Cross Module: In

order that the Cross

Module can be

installed easily,

please make sure

the bolts haven’t

been fastened too

tight. Install the

Cross Module as

picture show, fasten

the bolt for 2 or 3

circle, move it to

wherever need to

connect with Inter

Clamp, End Clamp

or Interfaces.

Fasten it tightly.

(Suggested torque

force: 8 N·m).



Xiamen, China 361022 Fax: +86 592 6771575


3.2 Installation of Rail

3.2.1 Put the Rail

onto the Interface,

fixing it with the

clamp, but not

fastened, as

showed.

3.2.2 Install the

Rail onto Interfaces

in rows as planned,

levelling by a rope

or laser ensuring

all the Rails are in

a line. Fastened all

the bolts after

thorough check as

showed in right.

(Suggested force:

8 N·m）

3.2.3 Install Rail

Connector:

If there’re different

lengths of rails,

then start from the

shortest one.

Install the rails onto

the interfaces by

M8 Hexagon Bolt,

Flat Washer, String

Washer and Cross

Module as showed.



Xiamen, China 361022 Fax: +86 592 6771575


3.3 Installation of Panels

3.3.1 Place the panels

onto the rail, fix it with

End Clamps a showed in

right. (Suggested torque

force: 8N·m)

3.3.2 Fix the panel with

Inter Clamps as well as

showed, fasten it slightly.

3.3.3 Place the other

panel under the Inter

Clamp, fastening the

bolts of Inter Clamp.

(Suggested torque

force: 8N·m)

Caution: Anti-slipping

should be placed in the

bottom rail slot as

showed.

3.3.4 Fix the panels in the

end of each line by End

Clamps. (Suggested

Torque force: 8N·m)

18mm



Xiamen, China 361022 Fax: +86 592 6771575


3.3.5 Install the upper line

panels, a gap around

18-20mm need to be

remained between the

two lines considering of

the sunlight angle. Finish

the installation in the

same procedure until all

the panels are installed

successfully.



Xiamen, China 361022 Fax: +86 592 6771575


4. 15 year limited Product Warranty, 5 year limited Finish Warranty

Mibet (Xiamen) New Energy Co., Ltd. (hereinafter as “Mibet Energy”) warrants to

the original purchaser (“NSEW Trading Pty Ltd.”) of products that it manufactures

(“Solar PV Mounting Systems”) at the original installation site that the Product shall

be free from defects in material and workmanship for a period of fifteen (15) years,

except for the under normal atmospheric conditions for a period of five (5) years,

from the earlier of 1). The date the installation of the Product is completed, or 2). 30

days after the purchase of Product by the original Purchaser (“Finish Warranty”).

The Finish Warranty does not apply to any foreign residue deposited on the finish. All

installations in corrosive atmospheric conditions are excluded. The Finish Warranty is

VOID if the practices specified by AAMA 609 & 610-02 –“Cleaning and

Maintenance for Architecturally Finished Aluminum” (www.aamanet.org) are not

followed by Purchaser. This Warranty does not cover damage to the Product that

occurs during its shipment, storage, or installation.

This Warranty shall be VOID if installation of the Product is not performed in

accordance with Mibet’s written installation instructions, or if the Product has been

modified, repaired, or reworked in a manner not previously authorized by Mibet IN

WRITING, or if the Product is installed in an environment for which it was not

designed. Mibet shall not be liable for consequential, contingent or incidental

damages arising out of the use of the Product by Purchaser under any circumstances.

If within the specified Warranty periods the Product shall be reasonably proven to be

defective, then Mibet shall repair or replace the defective Product, or any part thereof,

in Mibet’s sole discretion. Such repair or replacement shall completely satisfy and

discharge all of Mibet’s liability with respect to this limited Warranty. Under no

circumstances shall Mibet be liable for special, indirect or consequential damages

arising out of or related to use by Purchaser of the Product.

In addition to our Warranty against Defects, the Frame also comes with guarantees

that cannot be excluded under the Australian Consumer Law (Consumer Guarantees).

In the event that the Frame fails to satisfy a Consumer Guarantee, you are entitled to a

replacement or refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the Frame repaired or

replaced if the Frame fails to be of acceptable quality and the failure does not amount

to a major failure. Please note that in addition to the rights and remedies set out in this

document, you may also have other rights and remedies available to you under the

law.



Xiamen, China 361022 Fax: +86 592 6771575


*Manufacturers of related items, such as PV modules and flashings, may provide

written warranties of their own. Mibet’s limited Warranty covers only its Product, and

not any related items.

Making a claim

If you believe that the Frame is defective and you are an End-User, you may either

make a claim against the installer or builder from whom you purchased the Frame or

you may make a claim against us directly. In order to make a claim against us, you

must post, fax or email us a notice, using the contact details set out below.

In your notice you must provide: details of why you believe the Frame is defective; a

copy of your invoice, receipt or any other document which provides proof of

purchase;

Details of any expenses you have incurred in making your claim; and details of how

we should contact you.

Within a reasonable time after receipt of your claim we will contact you to arrange a

time to attend the premises at which the Frame is located.

Jurisdiction

Our Warranty against Defects is to be construed in accordance with the laws of

Victoria and any disputes will be determined by the exclusive jurisdiction of the

courts of Victoria.

Contact Details

NSEW Trading Pty Ltd

Level 5, 24 Albert Road

South Melbourne Vic 3205

Tel: 0417 387673

Email: [email protected]

Mibet (Xiamen) New Energy Co., Ltd. MRac Tile Roof...

Documents

Transcript of Mibet (Xiamen) New Energy Co., Ltd. MRac Tile Roof...