Goboservice Lighting by Sunland Optics SRL Via Gaspare del Fosso 33, 89127 Reggio Calabria

+39 0965 813264 Via Lombardia 269, 20047 Brugherio (MB)

+39 02 23166538 www.goboservice.com info@goboservice.com

INSTRUCTIONS, USE

AND MAINTENANCE

MANUAL FOR MERCURY PROJECTOR

BEFORE USE

This fixture must be operated only by adults.

Unpack the content from the box and check whether there are any damages caused by transportation.

Make sure that voltage and frequency in your area are the same the projector is certified to operate within.

You must connect the projector to a grounded wall socket.

Make sure there are no inflammable materials around the projector.

Put the projector in a place with good airflow. Do not use the projector in closed or semi-closed environments that

might increase the working temperature, thereby reducing the life of the unit.

The ambient temperature should not exceed 30°C.

INTRODUCTION

Read carefully the following instructions before any operation. The product described in this manual is a lighting

fixture for projecting a luminous beam. It is normally employed to illuminate, with a high level of brightness, small

areas that must be emphasized. The projector can be used to create luminous effects for decorative purposes. The

fixture must be used only for the purposes for which it has been designed and built. It is aimed to indoor and

outdoor lighting, every other use is not approved by the manufacturer and therefore it frees him from any

responsibility for damages deriving from improper or uncorrect use. This unit should be disposed of according to your

country’s regulations regarding the differentiated waste collection and disposal.

CLAUSES

This instructions manual must accompany the fixture. This manual must be stored carefully for at least 10 years, in a

place known by all the concerned persons. This manual has been written accordingly to the EU directives 2006/95/EC

and 2004/108/EC. The safety instructions contained in this manual cannot exclude other situations where the

product may result dangerous. Remember always to pay attention and to be careful when dealing with the product.

FOREWORD

For a proper use of the product, please follow these user's instructions to avoid damages to the product and to the

user. The aim of this manual is to inform you about installation, use, safety and maintenance. The manual does not

give only a description of the fixture, but it gives also useful advice in order to guarantee the maximum efficiency.

Since the knowledge of the manual is very important when dealing with emergencies, it must be read carefully

before using the product and must be consulted everytime difficulties or doubts should arise.

INSTALLATION AND USE

After undertaking the aforementioned checks, the user can install the projector. The installation must be executed

exclusively by qualified staff. The fixture must be fixed to wall with dowels, screws or other type of suitable

elements. After fixing the unit, you can connect it to the wall socket (you must connect it to a grounded wall socket).

Please follow the standard safety measures concerning any electrical appliance.

Caution ! never connect the projector to the wall socket when the installation is still taking place

Caution ! when the projector is connected to the wall socket, avoid any contact with water or humid surfaces or

moisture

After installing the fixture and connecting it to the ground, the unit can be switched on. If the lamp does not start or

there is a significant flicker, disconnect the unit from the wall socket before any action. The user is not allowed to

dissasemble the projector or to carry out any action on the electric part of it.

The projector's purpose is the projection of logos, texts, pictures. Should you see any cracks or breaks in the

housing, stop using the product immediately. Do not install the projector in a place where there are people or crowd

passing by. The fixture, if disconnected from the wall socket, is not harmful even when wet or under the rain.

The fixture works with low woltage AC and is as dangerous as a normal household appliance. The projector has been

designed according to all the available criteria of safety and has been built using materials fit for preventing dangers

and minimizing risks, but behave responsibly during use.

The projector is for indoor use only and should be kept away from moisture.

The projector gets very hot during use: avoid contact with the naked skin to prevent burns. You should wear gloves

when touching it.

When the projector is turned on, do not touch the housing or the cables and avoid watching in the lamp’s direction.

Before doing any maintenance on the unit, you must:

• switch off the unit and unplug it from the wall socket.

• wait 15 minutes before opening the housing.

After turning off the projector, wait 5-10 minutes before turning it on again, to avoid damages to the lamp.

If you need replacing the lamp, the engine or the ballast, please contact your reseller for genuine spare parts.

Never disassemble the projector or replace the faulty parts with non-genuine ones.

RESDIUAL RISKS

Even if the fixture has been built according to all laws and regulations, there is still some risk due to some structural

and functional aspects of the fixture. Do not disassemble the unit, and all maintenance operations must be carried

out only by specialized staff. The ballast is sealed for safety reasons and it should never be opened. Warranty is void

if the ballast seal is broken. Please put the projector in a place that can be easily seen by other people, to avoid

them stumble upon it. Avoid installing the unit in a place where it might fall from, hurting people underneath. Keep

children away at all times when the unit is switched on or when it is plugged to the wall socket.

MAINTENANCE

The only maintenance operation you can undertake is the cleaning of the unit, which must not be washed but only

cleaned with a soft damp cloth. Never clean the unit when it is switched on or when it is plugged to the wall socket.

FUSE REPLACEMENT

Inside a small locker on the back there is a 10A fuse, which will protect the projector from tension jolts.

FOCUSING

You can set the focus by one of the two lenses.

You only need to set the picture diameter by moving the lens.

LAMP REPLACEMENT

MOUNTING GOBOS

A gobo holder is supplied with the projector.

Two 9V plugs are located on the front panel for the feeding of accessories.

VENTILATION AND SAFETY SYSTEM

The projector is equipped with a forced ventilation system that guarantees the lamp’s cooling. It is always necessary

to maintain a good airflow around the projector.

If the projector overheates, its inner thermal protection will cause the lamp to switch off leaving the fans on until the

projector has cooled down enough to let the thermostat enable a new ignition of the lamp.

First make sure the projector is cold and disconnected from the mains system.

Put the projector on the ground, with the lenses facing the ceiling, then unscrew the lamp locker.

Wear gloves to avoid touching the lamp with your bare hands.

Unscrew the two metal bezels that hold the lampe in its right place, take out the old lamp, put the new in and screw

the two metal bezels to lock the lamp.

Make sure that the lamp's extremities have arrived at the end of the support staples.

If you own a HMI 575W projector, install the lamp with the little dot (on the central bulb) facing towards the ceiling.

Screw the locker cover back in place.

The unit has been delivered to you in perfect conditions. All users are required to follow strictly the safety instructions and

the notes contained in this manual. Any damage caused by the disregarding of the manual voids the warranty. We are not

responsible for damages or problems caused by the disregarding of the manual.

Any servicing or repairing must be undertaken only by the manufacturer. We are not responsible for damages caused by

unauthorized servicing or repairing. Unauthorized total or partial disassembling of the projector voids the warranty. Spare

parts such as lamps or fuses are not covered by the warranty.

We have the right to modify the manual’s content, anytime and without notice.

Pictures shown are for illustration purpose only.

IMPORTANT

Pictures shown are for illustration purpose only. Actual product may vary due to product enhancement.

REPLACEMENTS

Any replacement or substition must be carried out only by specialized staff. For any maintenance operation, please

contact your reseller.

CE MARKING

The projector described in this manual has been designed and built according to EU Directives 2006/95/EC (low vol-

tage) and 2006/95/EC (electromagnetic compatibility). This is confirmed by the CE mark on the product and by the

Declaration of Conformity at the end of this manual.

WASTE DISPOSAL

This unit should be disposed of according to your country’s regulations regarding the differentiated waste collection

and disposal.

WARRANTY

Our products have a 24-month warranty. We will, at our own choice, repair or replace your product. We need an

adequate amount of time for the operations required and for the spare parts delivery. All the costs for shipping the

parts to be replaced are charged on you. Unauthorized servicing or repairing voids the warranty. Only the original

purchaser can benefit the warranty. We are not subject to the warranty when the original purchaser resells the

product, the product is modified or any parts not produced by us are added to the product. Warranty does not cover

damages caused by excessive strain, such as after realizing there is an anomaly caused by misuse, improper

maintenance, or ignoring the use instructions. We are not responsible for any difficulties that might arise when

reselling the product or using it abroad in the country when it has been sold.

Should you need to use the warranty, please tell us the following information:

• Date of purchase

• Detailed description of the problem