Medium Bore Size Cylinder CMK2 Series - CKD · Medium Bore Size Cylinder CMK2 Series ... processes...
-
Upload
nguyenhanh -
Category
Documents
-
view
221 -
download
0
Transcript of Medium Bore Size Cylinder CMK2 Series - CKD · Medium Bore Size Cylinder CMK2 Series ... processes...
TIGHT CYLINDER CMK2 SERIES
Medium Bore Size CylinderCMK2 SeriesStainless steel variation
High corrosion resistance
High water resistant switch
Prevents water from entering
Uses food processing machinery grease [option]
All exterior metallic parts are made from 100% stainless steel (SUS304). Demonstrates high corrosion resistance even in environments exposed to water.
Special scraper provided as standard.Prevents water from entering the cylinder.
NSF-H1 rated product. Eliminates concerns over contamination caused by lubricants.
Uses a cylinder switch designed to prevent water from entering.
This logo represents our commitment to support food manufacturing processes with safe CKD products.
G2Uses a nitrile rubber heavy duty scraper to prevent water from entering
G3In addition to G2, uses fluoro rubber packing that has resistance to swelling
T2YLH
2CC-1298A
Tough against water.
1
Medium bore size cylinder double acting/exterior 100% stainless steel/water resistant type
CMK2-JG2/JG3 Series Bore size: φ 20/φ 25/φ 32/φ 40
JIS symbol
Descriptions CMK2-JG2/JG3Bore size mm φ 20 φ 25 φ 32 φ 40Actuation Double acting/water resistant typeWorking fluid Compressed airMax. working pressure MPa 1.0Min. working pressure MPa 0.15Proof pressure MPa 1.6 Ambient temperature °C -10 to 60 (no freezing)Port size Rc 1/8Stroke tolerance mm +2.0
0 (0 to 200) +2.40 (More than 200)
Working piston speed mm/s 50 to 500Cushion Rubber cushionLubrication Not required (use turbine oil type 1 ISO VG32 if necessary)Allowable absorbed energy J 0.166 0.308 0.424 0.639
Bore size (mm)Standard stroke length
(mm)Max. stroke length
(mm)Min. stroke length
(mm)Min. stroke length with
switch (mm)
φ 20, φ 25, φ 32, φ 40
25, 50, 75, 100, 150, 200, 250, 300
750 5 25
*1: Custom stroke length is available per mm.*2: Single foot type (LS) has the max. stroke length of 50 mm.
Stroke
Specifications
2
CMK2-JG2/JG3 SeriesSpecifications
Type/model No. Proximity switch specificationsDescriptions T2YLH/T2YLV T3YLH/T3YLVApplications Dedicated for programmable controller Programmable controller, relayOutput method - NPN OutputPower supply voltage - 10 to 28 VDCLoad voltage/current 10 to 30 VDC, 5 to 20 mA *1 30 VDC or less, 50 mA or lessIndicator light Red/green LED (Lit when ON)Leakage current 1 mA or less 10 μA or lessShock resistance 980 m / S2
Weight g 1 m: 33 3 m: 87 5 m: 142
Description/mounting type
Product weight when stroke length (S) = 0 mm Switch weight
(per 1 pc)
Switch rail+ band weight
Additional weight per S = 10 mmBasic
(00)Axial foot
(LB)Axial foot
(LS)Flange type
(FA,FB)Eye bracket type
(CC)Bore size (mm)φ 20 0.31 0.57 0.44 0.46 0.37 Refer to the weight
in the switch specifications.
0.005 0.01φ 25 0.32 0.58 0.45 0.47 0.39 0.005 0.01φ 32 0.43 0.69 0.56 0.58 0.55 0.009 0.02φ 40 0.65 0.91 0.78 0.80 0.90 0.009 0.02
Product weight when S = 0 mm .......... 0.56 kgAdditional weight when S = 50 mm .... "Additional weight when S = 10 mm" 0.02 × Product stroke length (50)
10 = 0.10 kg
Weight of 2 switches ........................... 0.062 kgWeight of switch rail + 2 bands ........... 0.018 kgProduct weight .................................... 0.56 kg + 0.1 kg + 0.062 kg + 0.018 kg = 0.74 kg
(Example) Product weight of CMK2-JG2-FA-32-50-T2YL-D
Cylinder weight
*1: Max. load current of 20 mA as above is applied at 25°C. The current is lower than 20 mA if the operating ambient temperature around the switch is higher than 25°C. (5 to 10 mA at 60°C)
Switch specifications
Theoretical thrust tableBore size
(mm)Operating direction
Working pressure MPa0.1 0.15 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
φ 20Push 31.4 47.1 62.8 94.2 1.26 × 102 1.57 × 102 1.88 × 102 2.20 × 102 2.51 × 102 2.83 × 102 3.14 × 102
Pull 23.6 35.3 47.1 70.7 94.2 1.18 × 102 1.41 × 102 1.65 × 102 1.88 × 102 2.12 × 102 2.36 × 102
φ 25Push 49.1 73.6 98.2 1.47 × 102 1.96 × 102 2.45 × 102 2.95 × 102 3.44 × 102 3.93 × 102 4.42 × 102 4.91 × 102
Pull 37.8 56.7 75.6 1.13 × 102 1.51 × 102 1.89 × 102 2.27 × 102 2.64 × 102 3.02 × 102 3.40 × 102 3.78 × 102
φ 32Push 80.4 1.21 × 102 1.61 × 102 2.41 × 102 3.22 × 102 4.02 × 102 4.83 × 102 5.63 × 102 6.43 × 102 7.24 × 102 8.04 × 102
Pull 69.1 1.04 × 102 1.38 × 102 2.07 × 102 2.76 × 102 3.46 × 102 4.15 × 102 4.84 × 102 5.53 × 102 6.22 × 102 6.91 × 102
φ 40Push 1.26 × 102 1.88 × 102 2.51 × 102 3.77 × 102 5.03 × 102 6.28 × 102 7.54 × 102 8.80 × 102 1.01 × 103 1.13 × 103 1.26 × 103
Pull 1.10 × 102 1.65 × 102 2.21 × 102 3.31 × 102 4.41 × 102 5.51 × 102 6.62 × 102 7.72 × 102 8.82 × 102 9.92 × 102 1.10 × 103
(Unit: N)
(Unit: kg)
3
CMK2-JG2/JG3 Series
A
B
C
D
E
G
H
*1: Single foot type (LS) has the max. stroke length of 50 mm.*2: Refer to page 1 for the min. stroke with switch.*3: Up to three switches can be installed. If four or more
switches are required, switch mounting brackets for the extra switches must be prepared separately.
*4: "I" and "Y" cannot be selected together.
Model: Medium bore size cylinderA Variation : Exterior 100% stainless steel + water resistant scraper + packing NBRB Mounting : Eye bracket integratedC Bore size : φ 32D Stroke : 50 mmE Switch model No. : Proximity switch T2YLH, lead wire 1 mF Switch quantity : 2 pcs. includedG Option : Foodstuffs grade grease specificationH Accessory : Rod clevis
CMK2-JG2-CC-32-50-T2YLH-D-FP1Y[Example of model No.]
Accessory*4
With switch
Without switch
How to order
T2YL YR20
20
50
50
00
00JG2
FP1CMK2
CMK2
Variation
Mounting type*1
Bore size
Stroke
Switch model No.* indicates the lead
wire length.
Option
F Switch quantity*3Precautions for model No. selection
Code ContentA VariationJG2 Exterior 100% stainless steel + water resistant scraper + packing NBRJG3 Exterior 100% stainless steel + water resistant scraper + packing FKM
B Mounting type00 BasicLB Axial foot (both sides)LS Axial foot (one side)FA Rod side flangeFB Head side flangeCC Eye bracket integrated
C Bore size (mm)20 φ 2025 φ 2532 φ 3240 φ 40
D Stroke (mm)Bore size Stroke *2 Custom stroke length
φ 20 5 to 750
In 1 mm incrementsφ 25 5 to 750φ 32 5 to 750φ 40 5 to 750
E Switch model No.Lead wireStraight
Lead wireL-shaped Contact Voltage Indicator Lead
wireT2YLH* T2YLV*
Proximity DC2-color display
2-wireT3YLH* T3YLV* 3-wire
* Lead wire lengthBlank 1 m (Standard)
3 3 m (Option)5 5 m (Option)
F Switch quantityR 1 on rod sideH 1 on head sideD 2T 3
G Option Blank StandardFP1 Foodstuffs grade grease specification
V Boss cutoff
H AccessoryI Rod eyeY Rod clevis (pin and snap ring attached)
JG2
4
CMK2-JG2/JG3 SeriesHow to order
Bore size (mm)φ 20 φ 25 φ 32 φ 40
Mounting bracket
Axial foot (LB, LS) CMK2-JG2-20-LS CMK2-JG2-20-LS CMK2-JG2-20-LS CMK2-JG2-40-LSCMK2-JG2-20-LS (LB head side)
Flange (FA, FB) CMK2-JG2-20-FA CMK2-JG2-20-FA CMK2-JG2-20-FA CMK2-JG2-20-FA (for FB)CMK2-JG2-40-FA (for FA)
*1: Regarding mounting brackets, mounting nuts are attached with the axial foot and flange types.*2: For axial foot types (LB), 2 sets of the above "CMK2-JG2-*-LS" are required.
How to order mounting bracket
Switch body only
SW
Mounting bracket
Mounting bracket set
Bore size(Item C on the previous page)
20
T2YLH
T2YLH
TCMK2
CMK2
How to order switch Switch body + mounting bracket set
Switch model No.(Item E on the previous page)
Bore size(Item C on the previous page)
20
Switch model No.(Item E on the previous page)
5
CMK2-JG2/JG3 Series
No. Part name Material Remarks No. Part name Material Remarks1 Piston rod Stainless steel
10 PistonPacking
JG2 Nitrile rubber
2 Rod nut Stainless steel JG3 Fluoro rubber
3 ScraperJG2 Nitrile rubber 11 Magnet -
JG3 Fluoro rubber 12 Wear ring Resin
4 RodPacking
JG2 Nitrile rubber 13 Piston B Aluminum alloy
JG3 Fluoro rubber 14 Spacer Steel Zinc chromate
5 Rod cover Stainless steel 15 Hexagon nut Steel Zinc chromate
6 Bush Dry bearing 16 Head cover Stainless steel
7 Cylinder tube Stainless steel 17 Switch - With switch only
8 Cushion rubber Urethane rubber 18 Band Stainless steel With switch only
9 Piston A Aluminum alloy 19 Pan head machine screw Stainless steel With switch only
20 Switch rail Stainless steel With switch only
Material of mounting bracketMounting type Material
LB/LS Stainless steel
FA/FB Stainless steel
Internal structure and parts list
Note: This product is a caulked type and cannot be disassembled.
Cannot be disassembled
Note : Mounting bracket will be attached to the product when shipping.
1516141312119 108765431 217201819
6
Code Basic (OO) basic dimensionsBore size (mm) A B C D F G QA HA K KK LL MR MB MM MN MO T
φ 20 20 13 18 21.4 30 16 8 35 14 M8 × 1.0 66 M26 × 1.5 M26 × 1.5 10 8 5 5
φ 25 23 17 20 26.4 32 16 8 35 14 M10 × 1.25 69 M26 × 1.5 M26 × 1.5 12 10 5 6
φ 32 23 17 20 33.6 36 16 8 35 14 M10 × 1.25 69 M26 × 1.5 M26 × 1.5 12 10 5 6
φ 40 25 19 22 41.6 45 16 8 38 14 M12 × 1.5 73 M30 × 1.5 M26 × 1.5 14 12 6 7
Code With switch Boss cutoffBore size (mm) U V WF X XF RD HD P P1 (Pθ) ° X
φ 20 28 16 28 130 48 7 6 23.1 19.5 22 114
φ 25 30 16 28 136 51 8.5 7.5 25.6 22 18 120
φ 32 34 16 28 136 51 8.5 7.5 30.1 25.5 15 120
φ 40 43 16 28 142 53 10.5 9.5 34.1 29.5 12 126
Basic (OO)
Dimensions
RD: Rod end max. sensitivity positonHD: Head end max. sensitivity position
CMK2-JG2/JG3 SeriesDimensions
φ M
M
MO
MN (Tang)
MB
KK
Hexagon B MR
Tang U1010
φ F
φ D
T
30.5GVC
G
A WF
30.5 16
8
K
VLL+stroke
X+stroke
RD
QA
HD
2-Rc1/8
HA
P1
(Pθ)
P8
8
X+stroke
XF
7
Code Axial foot (LS) basic dimensionsBore size (mm) A B C D G QA HA K KK LL MB MM T U V WF X
φ 20 20 13 18 21.4 16 8 35 14 M8 × 1.0 66 M26 × 1.5 10 5 28 16 28 130
φ 25 23 17 20 26.4 16 8 35 14 M10 × 1.25 69 M26 × 1.5 12 6 30 16 28 136
φ 32 23 17 20 33.6 16 8 35 14 M10 × 1.25 69 M26 × 1.5 12 6 34 16 28 136
φ 40 25 19 22 41.6 16 8 38 14 M12 × 1.5 73 M26 × 1.5 14 7 43 16 28 142
Note 1: Max. stroke length: 50.
Dimensions
Axial foot (one side) (LS)
Axial foot (LB)
CMK2-JG2/JG3 Series
Code Axial foot (LB) basic dimensions Mounting dimensionsBore size (mm) A B C D G QA HA KK LL MM T U V WF LA LB LC LD LF
φ 20 20 13 18 21.4 16 8 35 M8 × 1.0 66 10 5 28 16 28 149 12 23 7 5
φ 25 23 17 20 26.4 16 8 35 M10 × 1.25 69 12 6 30 16 28 155 12 23 7 5
φ 32 23 17 20 33.6 16 8 35 M10 × 1.25 69 12 6 34 16 28 155 12 23 7 5
φ 40 25 19 22 41.6 16 8 38 M12 × 1.5 73 14 7 43 16 28 161 12 23 7 5
Code With switchBore size (mm) LG LH LI LR LS LT RD HD P P1 (Pθ) °
φ 20 112 30 20 46 62 3 7 6 23.1 19.5 22
φ 25 115 30 20 46 62 3 8.5 7.5 25.6 22 18
φ 32 115 30 20 46 62 3 8.5 7.5 30.1 25.5 15
φ 40 119 30 20 46 62 3 10.5 9.5 34.1 29.5 12
Code Mounting dimensions With switch Boss cutoffBore size (mm) LB LC LD LF LG LH LI LR LS LT RD HD P P1 (Pθ) ° X LG
φ 20 12 23 7 48 62 30 20 46 62 3 7 6 23.1 19.5 22 114 46
φ 25 12 23 7 48 65 30 20 46 62 3 8.5 7.5 25.6 22 18 120 49
φ 32 12 23 7 48 65 30 20 46 62 3 8.5 7.5 30.1 25.5 15 120 49
φ 40 12 23 7 48 69 30 20 46 62 3 10.5 9.5 34.1 29.5 12 126 53
QA
HA
P1P
LILH LT
LR
LS4-φ LD
T 8
30.5GVC
A WF
30.5 16
VLL+stroke
φ M
M
KK
Hexagon B
Tang U
10 10
RD HD
2-Rc1/8
LA+stroke
LB LBLC LC
LG+stroke
LF
8(Pθ)
φ D
2-Rc1/8
8(Pθ)
4-φ LD
PP1
HA
LILH LT
LR
LS
φ M
M
KK
Hexagon B Tang U
X+stroke
T 8QA30.5GVC
A WF30.5 16 K
VLL+stroke
1010
RD HD
φ D
LBLCLF LG+stroke
MB
G8
X+stroke
8
Code Rod side flange (FA) basic dimensionsBore size (mm) A B C D F G QA HA K KK LL MB MM T U V WF X
φ 20 20 13 18 21.4 30 16 8 35 14 M8 × 1.0 66 M26 × 1.5 10 5 28 16 28 130
φ 25 23 17 20 26.4 32 16 8 35 14 M10 × 1.25 69 M26 × 1.5 12 6 30 16 28 136
φ 32 23 17 20 33.6 36 16 8 35 14 M10 × 1.25 69 M26 × 1.5 12 6 34 16 28 136
φ 40 25 19 22 41.6 45 16 8 38 14 M12 × 1.5 73 M26 × 1.5 14 7 43 16 28 142
Code Mounting dimensions With switch Boss cutoffBore size (mm) FC FD FF FG FH FL FM FT RD HD P P1 (Pθ) ° X FG
φ 20 28 7 23 87 44 64 80 5 7 6 23.1 19.5 22 114 71
φ 25 28 7 23 90 44 64 80 5 8.5 7.5 25.6 22 18 120 74
φ 32 28 7 23 90 44 64 80 5 8.5 7.5 30.1 25.5 15 120 74
φ 40 28 7 23 94 44 64 80 5 10.5 9.5 34.1 29.5 12 126 78
Code Head side flange (FB) basic dimensionsBore size (mm) A B C D G QA HA K KK LL MR MM T U V WF X
φ 20 20 13 18 21.4 16 8 35 14 M8 × 1.0 66 M26 × 1.5 10 5 28 16 28 130
φ 25 23 17 20 26.4 16 8 35 14 M10 × 1.25 69 M26 × 1.5 12 6 30 16 28 136
φ 32 23 17 20 33.6 16 8 35 14 M10 × 1.25 69 M26 × 1.5 12 6 34 16 28 136
φ 40 25 19 22 41.6 16 8 38 14 M12 × 1.5 73 M30 × 1.5 14 7 43 16 28 142
Dimensions Rod side flange (FA)
Head side flange (FB)
Code Mounting dimensions With switchBore size (mm) FC FD FH FJ FL FM FT RD HD P P1 (Pθ) °
φ 20 28 7 44 99 64 80 5 7 6 23.1 19.5 22
φ 25 28 7 44 102 64 80 5 8.5 7.5 25.6 22 18
φ 32 28 7 44 102 64 80 5 8.5 7.5 30.1 25.5 15
φ 40 28 7 44 106 64 80 5 10.5 9.5 34.1 29.5 12
CMK2-JG2/JG3 SeriesDimensions
2-Rc1/8
φ M
M
KK
Hexagon B
X+stroke
30.5VCA WF
30.5 168
VLL+stroke
10 10
RD HD
φ D
T
MRFT
FJ+stroke
HA
FL
FM
FC FH
4-φ FD
KK
Hexagon B4-φ FD
HA
10 φ D
FT
FF FG+stroke
FL
FM
FC FH
8
X+stroke
FG+stroke
2-Rc1/8
X+stroke
30.5 30.5 168
LL+stroke
10
HD
MB
φ F
KV
V
φ M
M
CA WF
RD
T
Tang U
QAG
G
QAG
Tang U
9
Dimensions Eye bracket integrated (CC)
CMK2-JG2/JG3 Series
Code Eye bracket integrated (CC) basic dimensions Mounting dimensionsBore size (mm) A B C D F G QA KK LL MM T U WF CA CB CC CD CJ CM
φ 20 20 13 18 21.4 30 32 24 M8 × 1.0 82 10 5 28 12 135 12 9 8 106 21
φ 25 23 17 20 26.4 32 32 24 M10 × 1.25 85 12 6 30 12 141 12 9 8 109 21
φ 32 23 17 20 33.6 36 32 24 M10 × 1.25 85 12 6 34 12 146 14 12 10 111 26
φ 40 25 19 22 41.6 45 32 24 M12 × 1.5 89 14 7 43 12 156 16 14 12 117 30
Code With switchBore size (mm) CO CQ RD HD P P1 (Pθ) °
φ 20 22 16 7 6 23.1 19.5 22
φ 25 24 16 8.5 7.5 25.6 22 18
φ 32 24 16 8.5 7.5 30.1 25.5 15
φ 40 30 20 10.5 9.5 34.1 29.5 12
KK
Hexagon B
MO
φ CDH102-Rc1/8
φ M
M
T
30.5C
A WF
30.5 16
8
LL+stroke
10 10
RD HD
φ D CB CC
CM
CJ+stroke
CA+stroke
(Pθ)
8
P
φ C
O
φ F
P1
CQ -0.1-0.3
U
QA
G
MN (Tang)
10
Model No. Compatible tubeBore size (mm) AA CA CD CH EW KK MA MC Weight
(g)M1-I-20S 20 14 30 10 19 8 M8 × 1.0 13 10 60
M1-I-30S 25/32 14 36 12 25 10 M10 × 1.25 16 12 106
M1-I-40S 40 14 36 12 25 10 M12 × 1.5 16 12 100
Model No. Compatible tubeBore size (mm) CA CB CD CH CL KK MB MC Weight
(g)M1-Y-20S 20 30 8 10 19 19 M8 × 1.0 13 10 99
M1-Y-30S 25/32 36 10 12 25 25 M10 × 1.25 16 12 197
M1-Y-40S 40 36 10 12 25 25 M12 × 1.5 16 12 193
Note: A pin and split washer pin are included.
Model No. Applicable tube bore size (mm) A D CD EL T X Y Weight
(g)M1-P-20S 20 37 4 10 28 1.6 10.5 18 29
M1-P-30S 25/32/40 46 4 12 37 2.3 12.5 22 50
Note: A pin and split washer pin for rod clevis use come with the product.
Accessory dimensions
Material: Stainless steel
Rod clevis pin (P)
Rod clevis (Y)
Rod eye (I)
Material: Stainless steel
Material: Stainless steel
CMK2-JG2/JG3 SeriesAccessories (rod eye/pin)
-0.1-0.2EW
19CH
AA
MA
CA
KK
CDH10
MC
+0.3CB
CLCH
MB
CA
KK
CDH10
MC
+0.1
T
2-φ D
A
EL4.5
4
φ CDf8
208
3.7
7.4
φ Y
φ X
11
Safety PrecautionsAlways read this section before use.
When designing and manufacturing a device using CKD products, the manufacturer is obligated to check that device safety mechanism, pneumatic control circuit, or water control circuit and the system operated by electrical control that controls the devices is secured.It is important to select, use, handle and maintain the product appropriately to ensure that the CKD product is used safely.Observe warnings and precautions to ensure device safety.Check that device safety is ensured, and manufacture a safe device.
1 This product is designed and manufactured as a general industrial machine part.It must be handled by an operator having sufficient knowledge and experience in handling.
2 Use this product in accordance with specifications.This product must be used within its stated specifications. In addition, never modify or additionally machine this product.This product is intended for use in general industrial machinery equipment or parts. It is not intended for use outdoors (except for products with outdoor specifications) or for use under the following conditions or environments.(Note that this product can be used when CKD is consulted prior to its usage and the customer consents to CKD product specifications. The customer should provide safety measures to avoid danger in the event of problems.)1 Use for applications requiring safety, including nuclear energy, railways, aircraft, marine vessels, vehicles, medical devices, devices or
applications in contact with beverages or foodstuffs, amusement devices, emergency cutoff circuits, press machines, brake circuits, or safety devices or applications.
2 Use for applications where life or assets could be significantly affected, and special safety measures are required.3 Observe organization standards and regulations, etc. related to the safety of device design and control, etc.
ISO4414, JIS B 8370 (General rules for pneumatic systems)JFPS2008 (Principles for pneumatic cylinder selection and use)Including High Pressure Gas Safety Act, Industrial Safety and Health Act, other safety rules, body standards and regulations, etc.
4 Do not handle, pipe, or remove devices before confirming safety.1 Inspect and service the machine and devices after confirming safety of all systems related to this product.2 Note that there may be hot or charged sections even after operation is stopped.3 When inspecting or servicing the device, turn OFF the energy source (air supply or water supply), and turn OFF power to the
facility. Discharge any compressed air from the system, and pay attention to possible water leakage and leakage of electricity.4 When starting or restarting a machine or device that incorporates pneumatic components, make sure that the system safety, such
as pop-out prevention measures, is secured.5 Observe warnings and cautions in the following pages to prevent accidents.
WARNING
The precautions are ranked as "DANGER", "WARNING" and "CAUTION" in this section.
DANGER:When a dangerous situation may occur if handling is mistaken leading to fatal or serious injuries, and when there is a high degree of emergency to a warning.
WARNING: If handled incorrectly, a dangerous situation may occur, resulting in death or serious injury.
CAUTION:When a dangerous situation may occur if handling is mistaken leading to minor injuries or physical damage.
Note that some items described as "CAUTION" may lead to serious results depending on the situation.Every item provides important information and must be observed.
Limited warranty and disclaimer
1 Warranty periodThis warranty shall be valid for one year after delivery to the customer's designated site.
2 Scope of warrantyIf any faults, found to be the responsibility of CKD, occur during the above warranty term, the product shall be replaced, the required replacement parts provided free of charge, or shall be repaired at the CKD factory free of charge.This Limited Warranty will not apply to:(1) Failures due to use outside the conditions and environments set forth in the catalog or these specifications.(2) Failures resulting from factors other than this product.(3) Failures caused by improper use of the product.(4) Failures resulting from modifications or repairs made without CKD consent.(5) Failures caused by matters that could not be predicted with the technologies in practice when the product was
delivered.(6) Failures resulting from natural disasters or accidents for which CKD is not liable.The warranty covers the actually delivered product, and does not cover any damage resulting from losses induced by faults in the delivered product.
3 Compatibility checkThe customer is responsible for confirming the compatibility of CKD products with the customer's systems, machines and equipment.
12
Pneumatic components
Safety PrecautionsAlways read this section before use.Refer to "Pneumatic Cylinders I (No. CB-029SA)" for general information on cylinders and cylinder switches.
Product-specific cautions: Medium bore size cylinder CMK2-JG2/JG3 Series
Design/selectionCAUTION
Consider use only after carefully confirming device structural materials (only exterior parts are stainless steel), the valve structure, working fluids, and compatibility with the working environment.
Bearings used in cylinders contain trace amounts of mineral oil. This is processed so as not to cause discharges within product specifications. However, keep the installation location in mind.
Mounting, installation and adjustmentCAUTION
Do not turn the cover. If the cover is turned when mounting the cylinder or screwing the pipe fitting into the port, the breakage from the cover connection could occur.
During Use & maintenance
CAUTION When moving the switch position to the stroke length direction
When fine-tuning the switch position, move the band position.
Loosen the switch fixing screw, shift the switch along the rail, then tighten at the specified position.Tighten using a tightening torque of 0.5 to 0.7 N·m.
When moving the switch position to the circumferential direction
Loosen the band fixing screw, shift the switch rail in the circumference direction, then tighten at the specified position.Tightening torque is 0.6 to 0.8 N·m.
Minimize cleaning of the sliding sections. Grease should be applied after cleaning. If water splattering is temporary, periodically apply grease. Contact CKD for details on maintenance greases.
Do not apply an eccentric load to the piston rod. The service life of the scraper or bearing could be shortened.
Mount the speed controller on the cylinder. Mount the speed controller on the cylinder.Use each cylinder within the applicable working piston speed range.
If not exposed to water splattering, the lubrication of the piston rod will run out and the service life will be shortened.
Apply grease when using the pin to prevent seizing.
When shifting the band position Loosen the band fixing screw, shift the switch rail and band along the cylinder tube, and tighten at the specified position.Tightening torque is 0.6 to 0.8 N·m.
BandSwitch rail Cylinder tubeSwitchBand fixing screw
TOH
CK
D
After installing, check for leaks from pipes and for wire connections, and check that the product is correctly installed.
Do not use products as footing or place any heavy objects on top of the products.
If the product has not been in use for over one month, perform a test run before starting actual operation.
13
Related products
FP Series products for foodstuffs manufacturing processes
A wide range of products from air filters to actuators that can be used safely and securely in foodstuffs manufacturing processes.
FP1 Series eliminates concerns over contamination caused by lubricants, allowing the use of foodstuffs grade (NSF H1) lubricant.
In addition to FP1, FP2 Series uses resin and rubber materials that are compatible with the Food Sanitation Act.
Catalog No. CC-1271A
Equipment for food m
anufacturing processes FP seriesCKD INDIA PRIVATE LTD.
TAIWAN CKD CORPORATION
CKD UK OFFICE
CKD EUROPE BRANCH
CKD CZECH OFFICE CKD SINGAPORE PTE. LTD.CKD CORPORATION BRANCH OFFICE
M-CKD PRECISION SDN.BHD.
CKD THAI CORPORATION LTD.
:Distributors
CKD USA CORPORATION
CKD KOREA CORPORATION
CKD(SHANGHAI) CORPORATION
PT CKD TRADING INDONESIA
CKD FRANKFURTOFFICE
CKD VIETNAM ENGINEERING CO.,LTD
CKD MEXICO, S. DE R.L. DE C.V.
●Specifications are subject to change without notice.
The goods and/or their replicas, or the technology and/or software found in this catalog are subject to complementary export regulations by Foreign Exchange and Foreign Trade Law of Japan. If the goods and/or their replicas, the technology and/or software found in this catalog are to be exported, law requires that the exporter makes sure that they will never be used for the development or manufacture of weapons for mass destruction.
2016.9CKD Corporation 2016 All copy rights reserved.
Website http://www.ckd.co.jp/
U.S.A.CKD USA CORPORATION●CHICAGO HEADQUARTERS
4080 Winnetka Avenue, Rolling Meadows, IL 60008, USAPHONE +1-847-368-0539 FAX +1-847-788-0575・CINCINNATI OFFICE・SAN ANTONIO OFFICE・SAN JOSE OFFICE・DETROIT OFFICE
MexicoCKD MEXICO, S. DE R.L. DE C.V.
Cerrada la Noria No. 200 Int. A-01, Querétaro Park II, Parque Industrial Querétaro, Santa Rosa Jáuregui, Querétaro, C.P. 76220, MéxicoPHONE +52-442-161-0624
EuropeCKD CORPORATION EUROPE BRANCH
De Fruittuinen 28 Hoofddorp, the NetherlandsPHONE +31-(0)23-5541490 FAX +31-(0)23-5541491・CZECH OFFICE・UK OFFICE・FRANKFURT OFFICE
MalaysiaM-CKD PRECISION SDN.BHD.●HEAD OFFICE
Lot No.6,Jalan Modal 23/2, Seksyen 23, Kawasan MIEL,Fasa 8, 40300 Shah Alam,Selangor Darul Ehsan, MalaysiaPHONE +60-(0)3-5541-1468 FAX +60-(0)3-5541-1533・JOHOR BAHRU BRANCH OFFICE・PENANG BRANCH OFFICE
ThailandCKD THAI CORPORATION LTD.●SALES HEADQUARTERS
Suwan Tower, 14/1 Soi Saladaeng 1, North Sathorn Road, Kwaeng Silom, Khet Bangrak, Bangkok 10500, ThailandPHONE +66-(0)2-267-6300 FAX +66-(0)2-267-6305・RAYONG OFFICE・NAVANAKORN OFFICE・EASTERN SEABOARD OFFICE・LAMPHUN OFFICE・KORAT OFFICE・AMATANAKORN OFFICE・PRACHINBURI OFFICE・SARABURI OFFICE
SingaporeCKD SINGAPORE PTE. LTD.
No.33 Tannery Lane #04-01 Hoesteel Industr ial Building, Singapore 347789, Singapore PHONE +65-67442623 FAX +65-67442486CKD CORPORATION BRANCH OFFICE
No.33 Tannery Lane #04-01 Hoesteel Industr ial Building, Singapore 347789, Singapore PHONE +65-67447260 FAX +65-68421022・INDIA LIAISON OFFICE BANGALORE・INDIA LIAISON OFFICE DELHI
IndiaCKD INDIA PRIVATE LTD.
Unit No. 607, 6th Floor, Welldone Tech Park, Sector 48, Sohna Road, Gurgaon-122018, Haryana, IndiaPHONE +91-(0)124-418-8212
IndonesiaPT CKD TRADING INDONESIA
Wisma Keiai, 17th Floor, Jl. JendralSudirman Kav.3, Jakarta 10220, IndonesiaPHONE +62-(0)21-572-3220 FAX +62-(0)21-573-4112
VietnamCKD VIETNAM ENGINEERING CO.,LTD.
18th Floor, CMC Tower, Duy Tan Street, Cau Giay District, Hanoi, Vietnam PHONE +84-4-37957631 FAX +84-4-37957637
Taiwan台湾喜開理股 有限公司TAIWAN CKD CORPORATION
16F-3, No. 7, Sec. 3, New Taipei Blvd., Xinzhuang Dist., New Taipei City 242, TaiwanPHONE +886-(0)2-8522-8198 FAX +886-(0)2-8522-8128・新竹営業所(HSINCHU OFFICE)・台中営業所(TAICHUNG OFFICE)・台南営業所(TAINAN OFFICE)
China喜開理(上海)機器有限公司CKD(SHANGHAI)CORPORATION●営業部 /上海浦西事務所(SALES HEADQUARTERS / SHANGHAI PUXI OFFICE)
Room 601, 6th Floor, Yuanzhongkeyan Building, No. 1905 Hongmei Road, Xinhui District, Shanghai 200233, ChinaPHONE +86-(0)21-61911888 FAX +86-(0)21-60905356・上海浦東事務所(SHANGHAI PUDONG OFFICE)・無錫事務所(WUXI OFFICE)・杭州事務所(HANGZHOU OFFICE)・寧波事務所(NINGBO OFFICE)・南京事務所(NANJING OFFICE)・蘇州事務所(SUZHOU OFFICE)・昆山事務所(KUNSHAN OFFICE)・北京事務所(BEIJING OFFICE)・天津事務所(TIANJIN OFFICE)・長春事務所(CHANGCHUN OFFICE)・大連事務所(DALIAN OFFICE)・青島事務所(QINGDAO OFFICE)・済南事務所(JINAN OFFICE)・烟台事務所(YANTAI OFFICE)・瀋陽事務所(SHENYANG OFFICE)・重慶事務所(CHONGQING OFFICE)・成都事務所(CHENGDU OFFICE)・西安事務所(XIAN OFFICE)・武漢事務所(WUHAN OFFICE)・鄭州事務所(ZHENGZHOU OFFICE)・長沙事務所(CHANGSHA OFFICE)・広州事務所(GUANGZHOU OFFICE)・深圳西事務所(WEST SHENZHEN OFFICE)・深圳東事務所(EAST SHENZHEN OFFICE)・東莞事務所(DONGGUAN OFFICE)・厦門事務所(XIAMEN OFFICE)
KoreaCKD KOREA CORPORATION●HEADQUARTERS(3rd Floor), 44, Sinsu-ro, Mapo-gu, Seoul 121-856, KoreaPHONE +82-(0)2-783-5201~5203 FAX +82-(0)2-783-5204・水原営業所(SUWON OFFICE)・天安営業所(CHEONAN OFFICE)・蔚山営業所(ULSAN OFFICE)
□ 2-250 Ouji Komaki, Aichi 485-8551, Japan□ PHONE +81-(0)568-74-1338 FAX +81-(0)568-77-3461 Equipment for
Food manufacturing processes FP series
Equipment for Food manufacturing processes
FP series
Various needs on food production processes have shaped our products.
1CC-1271A
CMK2-JG2/JG3 Series
Equipment for food manufacturing processes FP seriesEquipment for food manufacturing processes FP series
Prevents food contamination caused by lubricant. Food grade lubricant (NSF H1) is used.Prevents food contamination caused by lubricant. Food grade lubricant (NSF H1) is used.
FP1FP1FP1FP1SCPD3 Series
Pencil shaped cylinder
FJ Series
Floating joint
CKG Series
3-way jaw bearing chuck
VSP Series
Suction pad
HMF Series
Compact wide parallel hand
4G Series
3/4/5-port pilot operated valve
GW Series
Fittings
ZW Series
Fittings(stainless-steel)
CMK2 Series
Medium bore size cylinder
CMK2J Series
Medium bore size cylinder (stainless steel)
SCM Series
Round shaped cylinder
SCG Series
Tie rod air cylinder
SCA2 Series
Medium bore size cylinder, tie rod type
SCS2 Series
Large bore size cylinder
SSD2 Series
Compact cylinder
STG-M Series
Guided cylinder
FPV Series
Block valve
2QV/3QV Series
Quick valve
VSH/VSC Series
Discrete type ejector
APK Series
Pilot kick type 2-port solenoid valve
FH100 Series
Feather hand (mini-parallel hand)
CKL2 Series
Powerful chuck
SU/SD Series
High polymer membrane dryer
EVD Series
Digital electro-pneumatic regulator
DSC Series
Speed controller with adjusting dial
SCL2 Series
Speed controller, inline with push-in fitting
DVL-S Series
Needle valve with adjusting dial
SC-M5 Series
Miniature speed controller
SC3W Series
Speed controller, elbow with push-in fitting
SC1 Series
Speed controller
CKLG2 Series
Powerful chuck
BHA/BHG Series
Compact cross roller parallel hand
FH500 Series
Feather hand (mini-fulcrum hand)
W1*00-W8*00 Series
Filter/regulator
SMW/SMW2 Series
Metering valve with silencer
SRL3 Series
Rodless cylinder
AF Series
Medium main line filter
F1000-F8000 Series
Air filter
R1*00-R8*00 Series
Regulator
CHB/CHG Series
Compact rotary valve
MXB/MXG Series
Oil-free motor driven 2-port ball valve
SPKSeries
Pilot kick type 2-port solenoid valve for steam
MYB3Series
Metal free solenoid valve
HB Series
High corrosion resistant direct acting 2-port solenoid valve
P1100-P8100 Series
Reed switch type compact pressure switch
V1000/V3000/V3010/V6010/Series
Shut-off valve
AG31/41/33/43/34/44Series
Direct acting 3-port solenoid valve (general purpose valve)
M(X)1000-M(X)8000 Series
Oil mist filter
SAB Series
Air operated 2-port valve
NAP Series
Air operated 3-port valve
EXA Series
Pilot operated 2-port solenoid valve for compressed air
ADK11-Z Series
Pilot operated 2-port solenoid valve for dry air (general purpose valve)
LAD Series
Diaphragm type cylinder valve
NAD Series
Diaphragm type cylinder valve
GNAD Series
Diaphragm type cylinder valve, manifold
FWD Series
Compact pilot operated solenoid valve for water
USB/G Series
Compact direct acting 2/3-port solenoid valve
AB31/41 Series
Direct acting 2-port solenoid valve (general purpose valve)
FP2FP2FP2FP2FP2FP2FP2Materials conforming to the Food Sanitation Act are used.
Standard model supports. ............................................................................. P239
Contact CKD for details. ................................................................................ P240
Related products ........................................................................................... P243
Equipment for food manufacturing processes FP series
14
CMK2-JG2/JG3 SeriesRelated productsEquipment for food manufacturing processes FP seriesEquipment for food manufacturing processes FP series
Prevents food contamination caused by lubricant. Food grade lubricant (NSF H1) is used.Prevents food contamination caused by lubricant. Food grade lubricant (NSF H1) is used.
FP1FP1FP1FP1SCPD3 Series
Pencil shaped cylinder
FJ Series
Floating joint
CKG Series
3-way jaw bearing chuck
VSP Series
Suction pad
HMF Series
Compact wide parallel hand
4G Series
3/4/5-port pilot operated valve
GW Series
Fittings
ZW Series
Fittings(stainless-steel)
CMK2 Series
Medium bore size cylinder
CMK2J Series
Medium bore size cylinder (stainless steel)
SCM Series
Round shaped cylinder
SCG Series
Tie rod air cylinder
SCA2 Series
Medium bore size cylinder, tie rod type
SCS2 Series
Large bore size cylinder
SSD2 Series
Compact cylinder
STG-M Series
Guided cylinder
FPV Series
Block valve
2QV/3QV Series
Quick valve
VSH/VSC Series
Discrete type ejector
APK Series
Pilot kick type 2-port solenoid valve
FH100 Series
Feather hand (mini-parallel hand)
CKL2 Series
Powerful chuck
SU/SD Series
High polymer membrane dryer
EVD Series
Digital electro-pneumatic regulator
DSC Series
Speed controller with adjusting dial
SCL2 Series
Speed controller, inline with push-in fitting
DVL-S Series
Needle valve with adjusting dial
SC-M5 Series
Miniature speed controller
SC3W Series
Speed controller, elbow with push-in fitting
SC1 Series
Speed controller
CKLG2 Series
Powerful chuck
BHA/BHG Series
Compact cross roller parallel hand
FH500 Series
Feather hand (mini-fulcrum hand)
W1*00-W8*00 Series
Filter/regulator
SMW/SMW2 Series
Metering valve with silencer
SRL3 Series
Rodless cylinder
AF Series
Medium main line filter
F1000-F8000 Series
Air filter
R1*00-R8*00 Series
Regulator
CHB/CHG Series
Compact rotary valve
MXB/MXG Series
Oil-free motor driven 2-port ball valve
SPKSeries
Pilot kick type 2-port solenoid valve for steam
MYB3Series
Metal free solenoid valve
HB Series
High corrosion resistant direct acting 2-port solenoid valve
P1100-P8100 Series
Reed switch type compact pressure switch
V1000/V3000/V3010/V6010/Series
Shut-off valve
AG31/41/33/43/34/44Series
Direct acting 3-port solenoid valve (general purpose valve)
M(X)1000-M(X)8000 Series
Oil mist filter
SAB Series
Air operated 2-port valve
NAP Series
Air operated 3-port valve
EXA Series
Pilot operated 2-port solenoid valve for compressed air
ADK11-Z Series
Pilot operated 2-port solenoid valve for dry air (general purpose valve)
LAD Series
Diaphragm type cylinder valve
NAD Series
Diaphragm type cylinder valve
GNAD Series
Diaphragm type cylinder valve, manifold
FWD Series
Compact pilot operated solenoid valve for water
USB/G Series
Compact direct acting 2/3-port solenoid valve
AB31/41 Series
Direct acting 2-port solenoid valve (general purpose valve)
FP2FP2FP2FP2FP2FP2FP2Materials conforming to the Food Sanitation Act are used.
Standard model supports. ............................................................................. P239
Contact CKD for details. ................................................................................ P240
Related products ........................................................................................... P243
Equipment for food manufacturing processes FP series
Equipment for food manufacturing processes FP seriesEquipment for food manufacturing processes FP series
Prevents food contamination caused by lubricant. Food grade lubricant (NSF H1) is used.Prevents food contamination caused by lubricant. Food grade lubricant (NSF H1) is used.
FP1FP1FP1FP1SCPD3 Series
Pencil shaped cylinder
FJ Series
Floating joint
CKG Series
3-way jaw bearing chuck
VSP Series
Suction pad
HMF Series
Compact wide parallel hand
4G Series
3/4/5-port pilot operated valve
GW Series
Fittings
ZW Series
Fittings(stainless-steel)
CMK2 Series
Medium bore size cylinder
CMK2J Series
Medium bore size cylinder (stainless steel)
SCM Series
Round shaped cylinder
SCG Series
Tie rod air cylinder
SCA2 Series
Medium bore size cylinder, tie rod type
SCS2 Series
Large bore size cylinder
SSD2 Series
Compact cylinder
STG-M Series
Guided cylinder
FPV Series
Block valve
2QV/3QV Series
Quick valve
VSH/VSC Series
Discrete type ejector
APK Series
Pilot kick type 2-port solenoid valve
FH100 Series
Feather hand (mini-parallel hand)
CKL2 Series
Powerful chuck
SU/SD Series
High polymer membrane dryer
EVD Series
Digital electro-pneumatic regulator
DSC Series
Speed controller with adjusting dial
SCL2 Series
Speed controller, inline with push-in fitting
DVL-S Series
Needle valve with adjusting dial
SC-M5 Series
Miniature speed controller
SC3W Series
Speed controller, elbow with push-in fitting
SC1 Series
Speed controller
CKLG2 Series
Powerful chuck
BHA/BHG Series
Compact cross roller parallel hand
FH500 Series
Feather hand (mini-fulcrum hand)
W1*00-W8*00 Series
Filter/regulator
SMW/SMW2 Series
Metering valve with silencer
SRL3 Series
Rodless cylinder
AF Series
Medium main line filter
F1000-F8000 Series
Air filter
R1*00-R8*00 Series
Regulator
CHB/CHG Series
Compact rotary valve
MXB/MXG Series
Oil-free motor driven 2-port ball valve
SPKSeries
Pilot kick type 2-port solenoid valve for steam
MYB3Series
Metal free solenoid valve
HB Series
High corrosion resistant direct acting 2-port solenoid valve
P1100-P8100 Series
Reed switch type compact pressure switch
V1000/V3000/V3010/V6010/Series
Shut-off valve
AG31/41/33/43/34/44Series
Direct acting 3-port solenoid valve (general purpose valve)
M(X)1000-M(X)8000 Series
Oil mist filter
SAB Series
Air operated 2-port valve
NAP Series
Air operated 3-port valve
EXA Series
Pilot operated 2-port solenoid valve for compressed air
ADK11-Z Series
Pilot operated 2-port solenoid valve for dry air (general purpose valve)
LAD Series
Diaphragm type cylinder valve
NAD Series
Diaphragm type cylinder valve
GNAD Series
Diaphragm type cylinder valve, manifold
FWD Series
Compact pilot operated solenoid valve for water
USB/G Series
Compact direct acting 2/3-port solenoid valve
AB31/41 Series
Direct acting 2-port solenoid valve (general purpose valve)
FP2FP2FP2FP2FP2FP2FP2Materials conforming to the Food Sanitation Act are used.
Standard model supports. ............................................................................. P239
Contact CKD for details. ................................................................................ P240
Related products ........................................................................................... P243
Equipment for food manufacturing processes FP series
( 器 ) 世界モ (16.11.8)B-44.ai
CKD INDIA PRIVATE LTD.CKD INDIA PRIVATE LTD. BANGALORE BRANCH
TAIWAN CKD CORPORATION
CKD UK OFFICE
CKD CZECH OFFICE CKD SINGAPORE PTE. LTD.CKD CORPORATION BRANCH OFFICE
M-CKD PRECISION SDN.BHD.
CKD THAI CORPORATION LTD.
:Distributors
CKD USA CORPORATION
CKD KOREA CORPORATION
CKD(SHANGHAI) CORPORATION
PT CKD TRADING INDONESIA
CKD FRANKFURTOFFICE
CKD VIETNAM ENGINEERING CO.,LTD
CKD MEXICO, S. DE R.L. DE C.V.
CKD EUROPE B.V.CKD EUROPE BRANCH
●Specifications are subject to change without notice.
The goods and/or their replicas, the technology and/or software found in this catalog are subject to complementary export regulations by Foreign Exchange and Foreign Trade Law of Japan. If the goods and/or their replicas, the technology and/or software found in this catalog are to be exported, law requires that the exporter makes sure that they will never be used for the development and/or manufacture of weapons for mass destruction.
2017.06CKD Corporation 2017 All copy rights reserved.
U.S.A.CKD USA CORPORATION●CHICAGO HEADQUARTERS
4080 Winnetka Avenue, Rolling Meadows, IL 60008, USAPHONE +1-847-368-0539 FAX +1-847-788-0575
・CINCINNATI OFFICE・SAN ANTONIO OFFICE・SAN JOSE OFFICE・DETROIT OFFICE
MexicoCKD MEXICO, S. DE R.L. DE C.V.
Cerrada la Noria No. 200 Int. A-01, Querétaro Park II, Parque Industrial Querétaro, Santa Rosa Jáuregui, Querétaro, C.P. 76220, MéxicoPHONE +52-442-161-0624
EuropeCKD EUROPE B.V.
Beechavenue 125A, 1119 RB Schiphol-Rijk, The NetherlandsPHONE +31-23-554-1490CKD CORPORATION EUROPE BRANCH
Beechavenue 125A, 1119 RB Schiphol-Rijk, The NetherlandsPHONE +31-23-554-1490
・CZECH OFFICE・UK OFFICE・FRANKFURT OFFICE
MalaysiaM-CKD PRECISION SDN.BHD.●HEAD OFFICE
Lot No.6,Jalan Modal 23/2, Seksyen 23, Kawasan MIEL,Fasa 8, 40300 Shah Alam,Selangor Darul Ehsan, MalaysiaPHONE +60-(0)3-5541-1468 FAX +60-(0)3-5541-1533
・JOHOR BAHRU BRANCH OFFICE・PENANG BRANCH OFFICE
ThailandCKD THAI CORPORATION LTD.●SALES HEADQUARTERS
Suwan Tower, 14/1 Soi Saladaeng 1, North Sathorn Road, Kwaeng Silom, Khet Bangrak, Bangkok 10500, ThailandPHONE +66-(0)2-267-6300 FAX +66-(0)2-267-6305
・RAYONG OFFICE・NAVANAKORN OFFICE・EASTERN SEABOARD OFFICE・LAMPHUN OFFICE・KORAT OFFICE・AMATANAKORN OFFICE・PRACHINBURI OFFICE・SARABURI OFFICE
SingaporeCKD SINGAPORE PTE. LTD.
No.33 Tannery Lane #04-01 Hoesteel Industr ial Building, Singapore 347789, Singapore PHONE +65-67442623 FAX +65-67442486CKD CORPORATION BRANCH OFFICE
No.33 Tannery Lane #04-01 Hoesteel Industr ial Building, Singapore 347789, Singapore PHONE +65-67447260 FAX +65-68421022
IndiaCKD INDIA PRIVATE LTD.
Unit No. 607, 6th Floor, Welldone Tech Park, Sector 48, Sohna Road, Gurgaon-122018, Haryana, IndiaPHONE +91-(0)124-418-8212
CKD INDIA PRIVATE LTD. BANGALORE BRANCHNo. 201/B, 2nd Floor, Museum Terraces Apartment, No. 29, Museum Road, Bangalore-560001, Karnataka, IndiaPHONE +91-(0)80-4212-7008/7009 FAX +91-(0)80-4212-7007
IndonesiaPT CKD TRADING INDONESIA
Menara Bidakara 2, 18th Floor, Jl. Jend. Gatot Subroto Kav.71-73, Pancoran, Jakarta 12870, IndonesiaPHONE +62 21-2938-6601 FAX +62 21-2906-9470
VietnamCKD VIETNAM ENGINEERING CO.,LTD.
18th Floor, CMC Tower, Duy Tan Street, Cau Giay District, Hanoi, Vietnam PHONE +84-4-37957631 FAX +84-4-37957637
Taiwan台湾喜開理股 有限公司TAIWAN CKD CORPORATION
16F-3, No. 7, Sec. 3, New Taipei Blvd., Xinzhuang Dist., New Taipei City 242, TaiwanPHONE +886-(0)2-8522-8198 FAX +886-(0)2-8522-8128・新竹営業所(HSINCHU OFFICE)・台中営業所(TAICHUNG OFFICE)・台南営業所(TAINAN OFFICE)
China喜開理(上海)機器有限公司CKD(SHANGHAI)CORPORATION●営業部 /上海浦西事務所(SALES HEADQUARTERS / SHANGHAI PUXI OFFICE)
Room 601, 6th Floor, Yuanzhongkeyan Building, No. 1905 Hongmei Road, Xinhui District, Shanghai 200233, ChinaPHONE +86-(0)21-61911888 FAX +86-(0)21-60905356・上海浦東事務所(SHANGHAI PUDONG OFFICE)・無錫事務所(WUXI OFFICE)・杭州事務所(HANGZHOU OFFICE)・寧波事務所(NINGBO OFFICE)・南京事務所(NANJING OFFICE)・蘇州事務所(SUZHOU OFFICE)・昆山事務所(KUNSHAN OFFICE)・北京事務所(BEIJING OFFICE)・天津事務所(TIANJIN OFFICE)・長春事務所(CHANGCHUN OFFICE)・大連事務所(DALIAN OFFICE)・青島事務所(QINGDAO OFFICE)・済南事務所(JINAN OFFICE)・烟台事務所(YANTAI OFFICE)・瀋陽事務所(SHENYANG OFFICE)・重慶事務所(CHONGQING OFFICE)・成都事務所(CHENGDU OFFICE)・西安事務所(XIAN OFFICE)・武漢事務所(WUHAN OFFICE)・鄭州事務所(ZHENGZHOU OFFICE)・長沙事務所(CHANGSHA OFFICE)・広州事務所(GUANGZHOU OFFICE)・深圳西事務所(WEST SHENZHEN OFFICE)・深圳東事務所(EAST SHENZHEN OFFICE)・東莞事務所(DONGGUAN OFFICE)・厦門事務所(XIAMEN OFFICE)
KoreaCKD KOREA CORPORATION●HEADQUARTERS(3rd Floor), 44, Sinsu-ro, Mapo-gu, Seoul 121-856, KoreaPHONE +82-(0)2-783-5201~5203 FAX +82-(0)2-783-5204・水原営業所(SUWON OFFICE)・天安営業所(CHEONAN OFFICE)・蔚山営業所(ULSAN OFFICE)
□ 2-250, Ouji, Komaki City, Aichi, Japan 485-8551□ PHONE +81-(0)568-74-1338 FAX +81-(0)568-77-3461Website http://www.ckd.co.jp/
Revisions• Dimensions: Dimensions corrected