MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above...
Transcript of MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above...
![Page 2: MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above problem we have to draw the parts from 1 to 5 on Pro E and then after doing assembly,](https://reader033.fdocuments.in/reader033/viewer/2022041703/5e42c410688bf6549a104f8a/html5/thumbnails/2.jpg)
Problem:
Calculate the stress and displacement on both ends of PART2 using Pro Mechanica when a force of 600N is applied at an angle of 30° on PART 3. PART1 is grounded and the angles between the parts are shown in the figure above.
XpertSolver.com
![Page 3: MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above problem we have to draw the parts from 1 to 5 on Pro E and then after doing assembly,](https://reader033.fdocuments.in/reader033/viewer/2022041703/5e42c410688bf6549a104f8a/html5/thumbnails/3.jpg)
SOLUTION:
For solving the above problem we have to draw the parts from 1 to 5 on Pro E and then after doing assembly, have to apply Pro Mechanica for finding out the stress applied and the resultant displacement on both ends of part 2 after applying a force of 600N at an angle of 30 degree on Part 3.
The ends of part 2 will be named as right end and left end.
First step will be to draw the parts that are:
Part 1:
XpertSolver.com
![Page 5: MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above problem we have to draw the parts from 1 to 5 on Pro E and then after doing assembly,](https://reader033.fdocuments.in/reader033/viewer/2022041703/5e42c410688bf6549a104f8a/html5/thumbnails/5.jpg)
Part 5:
Then after doing assembly, Pro Mechanica is applied and the snapshots and results are as follows:
STRESS ON PART 2: ( Left End)
XpertSolver.com
![Page 6: MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above problem we have to draw the parts from 1 to 5 on Pro E and then after doing assembly,](https://reader033.fdocuments.in/reader033/viewer/2022041703/5e42c410688bf6549a104f8a/html5/thumbnails/6.jpg)
STRESS ON PART 2: ( Right End)
DISPLACEMENT OF PART 2 ( Right End):
XpertSolver.com
![Page 7: MEDICAL DEVICE DESIGN AND STANDARDS (Pro E) · 2016-10-16 · SOLUTION: For solving the above problem we have to draw the parts from 1 to 5 on Pro E and then after doing assembly,](https://reader033.fdocuments.in/reader033/viewer/2022041703/5e42c410688bf6549a104f8a/html5/thumbnails/7.jpg)
DISPLACEMENT OF PART 2 ( Right End):
RESULTS:
The stress and displacement on both ends of PART2 is given as:
Sr No End Divisions Stress Displacement
1 Right End 2.897Kpa 0.0003cm
2 Left End 2.084kpa 2.904cm
CONCLUSION:
Hence it is concluded that the stress on both ends is nearly same ( as also shown by same color as per matched by color chart ) and there is a great difference in displacement , very less displacement nearly negligible on right side and much more on left side of part 2.
XpertSolver.com