MCQS

41
CS601 Note: VuGujranwala.com is not responsible for any solved solution, but honestly we are trying our best to Guide correctly. Exam Term : Final Total MCQS : 287 Prepared By : page 1 / 41

description

Multiple choice questions of Communication systems

Transcript of MCQS

CS601 

 Note: VuGujranwala.com is not responsible for any solved solution, but honestly we are trying

our best to Guide correctly. 

Exam Term :   Final       Total MCQS :     287      

 Prepared By : 

page 1 / 41

1 - First commercial modems are developed in

1.     19472.     19503.     19604.     1970       Correct Choice : 4             From Lectuer # 23

www.vugujranwala.com

2 - Traditional modem's uploading data rate is

1.     33.3kbps2.     33.5kbps3.     33.6kbps4.     56kbps       Correct Choice : 3             From Lectuer # 23

www.vugujranwala.com

3 - In traditional modem, maximum data rate in downloading direction is

1.     33.3kbps2.     33.5kbps3.     33.6kbps4.     56kbps       Correct Choice : 4             From Lectuer # 23

www.vugujranwala.com

4 - What is the major factor that makes coaxial cable less susceptible to noise thantwisted-pair cable?

1.     Outer conductor2.     Inner conductor3.     Diameter of cable4.     Insulating material       Correct Choice : 1             From Lectuer # 24

www.vugujranwala.com

5 - Transmission media are usually categorized as _____________

1.     Fixed or Unfixed2.     Guided or Unguided3.     Determinate or Indeterminate4.     Metallic or Nonmetallic       Correct Choice : 2             From Lectuer # 24

www.vugujranwala.com

6 - Radio wave and microwave frequencies range from _________.

1.     3 to 300 KHz2.     300 KHz to300 KHz to 3 GHz3.     3 KHz to 300 GHz4.     3 KHz to 3000 GHz

page 2 / 41

       Correct Choice : 3             From Lectuer # 24www.vugujranwala.com

7 - Classes of Transmission Media are _________

1.     Electromagnetic Spectrum2.     Coxial and Twisted Cable Media3.     Guided and Unguided Media4.     None of Given       Correct Choice : 3             From Lectuer # 24

www.vugujranwala.com

8 - _______ cable consists of an inner copper core and a second conducting outer sheath.

1.     Coaxial2.     Twisted-pair3.     Fiber-optic4.     Shielded twisted-pair       Correct Choice : 1             From Lectuer # 24

www.vugujranwala.com

9 - In fiber optics the signal source is ____________waves.

1.     Light2.     Radio3.     Infrared4.     Very Low frequency       Correct Choice : 1             From Lectuer # 24

www.vugujranwala.com

10 - In data link layer, communication requires at least ___________ devices workingtogether.

1.     32.     23.     44.     1       Correct Choice : 2             From Lectuer # 24

www.vugujranwala.com

11 - Category 1 UTP cable is most often used in _______ networks.

1.     Infrared2.     Telephone3.     Fast Ethernet4.     Traditional Ethernet       Correct Choice : 2             From Lectuer # 24

www.vugujranwala.com

12 - The _______ is an association that sponsors the use of infrared waves.

1.     EIA2.     IrDA3.     FCC

page 3 / 41

4.     PUD       Correct Choice : 2             From Lectuer # 24

www.vugujranwala.com

13 - BNC connectors are used by _______ cables

1.     Fiber-optic2.     UTP3.     STP4.     Coaxial       Correct Choice : 4             From Lectuer # 24

www.vugujranwala.com

14 - In CRC there is no error if the remainder at the receiver is _______.

1.     Nonzero2.     The quotient at the sender3.     Equal to the remainder at the sender4.     Zero       Correct Choice : 4             From Lectuer # 24

www.vugujranwala.com

15 - BW of the local loop telephone line is

1.     4kHz2.     4bps3.     33.6kHZ4.     56 kHZ       Correct Choice : 1             From Lectuer # 24

www.vugujranwala.com

www.vugujranwala.com

17 - Metal cables use

1.     Voice band frequency2.     Radio frequency3.     visible light4.     both a and b       Correct Choice : 1             From Lectuer # 24

www.vugujranwala.com

18 - Electromagnetic signal can not travel through

1.     Vavuum2.     air3.     Transmission media4.     none of these       Correct Choice : 4             From Lectuer # 24

www.vugujranwala.com

19 - Classes of transmission media

1.     1

page 4 / 41

2.     23.     34.     4       Correct Choice : 2             From Lectuer # 24

www.vugujranwala.com

20 - Higher grades of STP cables are used in many LAN technologies including ethernetand token ring

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 24

www.vugujranwala.com

21 - Categories of UTP ccbles is

1.     22.     33.     44.     5       Correct Choice : 4             From Lectuer # 24

www.vugujranwala.com

22 - In which categories, the next higher grade, suitable for voice and data transmission ofup to 4Mbps

1.     Category 02.     Category 13.     Category 24.     Category 3       Correct Choice : 3             From Lectuer # 24

www.vugujranwala.com

23 - _______ is the propagation method subject to the greatest distortion.

1.     Single-mode2.     Multimode step-index3.     Multimode graded-index4.     Multimode single-index       Correct Choice : 2             From Lectuer # 25

www.vugujranwala.com

24 - The material of core and cladding in fiber optic cable is same.

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 25

www.vugujranwala.com

25 - STP is more expensive than UTP and is less susceptible to noise

page 5 / 41

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 25

www.vugujranwala.com

26 - STP can eliminate a phenomenon called Crosstalk

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 25

www.vugujranwala.com

27 - In fiber optic cable, the signal source is__________ waves

1.     Infrared2.     Light3.     Radio4.     Very Low Frequency       Correct Choice : 2             From Lectuer # 25

www.vugujranwala.com

28 - The RG number gives us information about ________.

1.     Twisted pairs2.     Coaxial cables3.     Optical fibers4.     all of the given       Correct Choice : 2             From Lectuer # 25

www.vugujranwala.com

29 - Transmission media are usually categorized as _______.

1.     Guided or unguided2.     Fixed or unfixed3.     Determinate or indeterminate4.     Metallic or nonmetallic       Correct Choice : 1             From Lectuer # 25

www.vugujranwala.com

30 - The RG number gives us information about _______.

1.     Optical fibers2.     Twisted pairs3.     Coaxial cables4.     All the above       Correct Choice : 3             From Lectuer # 25

www.vugujranwala.com

31 - The inner core of an optical fiber is _______ in composition.

page 6 / 41

1.     Copper2.     Bimetallic3.     Glass or plastic4.     Liquid       Correct Choice : 3             From Lectuer # 25

www.vugujranwala.com

32 - When we talk about unguided media, usually we are referring to _______.

1.     Metallic wires2.     Nonmetallic wires3.     The air4.     None of the above       Correct Choice : 3             From Lectuer # 25

www.vugujranwala.com

33 - In an environment with many high-voltage devices, the best transmission mediumwould be _________.

1.     Twisted-pair cable2.     Coaxial cable3.     The atmosphere4.     Optical fiber       Correct Choice : 4             From Lectuer # 25

www.vugujranwala.com

34 - Optical fibers, unlike wire media, are highly resistant to _______.

1.     High-frequency transmission2.     Low-frequency transmission3.     Refraction4.     Electromagnetic interference       Correct Choice : 4             From Lectuer # 25

www.vugujranwala.com

35 - STP is more expensive than UTP but is less susceptible to noise

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 25

www.vugujranwala.com

36 - Range of coaxial cable

1.     10kHZ to 100 kHz2.     100kHz to 500khz3.     100khz to 500MHz4.     500Mhz to 1GB       Correct Choice : 3             From Lectuer # 25

www.vugujranwala.com

page 7 / 41

www.vugujranwala.com

www.vugujranwala.com

39 - Reflection occurs when

1.     angle of incidence becomes less than critical angle2.     angle of refraction becomes less than critical angle3.     angle of refracted becomes greater than critical angle4.     angle of incidence becomes greater than critical angle       Correct Choice : 4             From Lectuer # 25

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

42 - Cable that connects the subscriber telephone to the nearest end office in a local loopis called _______

1.     Twisted-pair cable2.     Coaxial cable3.     Fiber-optic cable4.     Subscriber cable       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

43 - Which of the following is not a guided medium?

1.     Twisted Pair2.     Fiber Optic Cable3.     Coaxial Cable4.     Atmosphere       Correct Choice : 4             From Lectuer # 26

www.vugujranwala.com

44 - In an environment with many high-voltage devices, the best transmission mediumwould be _________.

1.     Atmosphere2.     Coaxial Cable3.     Twisted Pair4.     Fiber Optic Cable       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

45 - Troposhpheric Propagation is in two ways light of sight and broadcast.

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

page 8 / 41

46 - Ionosphere is the layer of atmosphere above the troposhere but below space

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

47 - In ______________ method a signal can be directed in a straight from Antenna toantenna.

1.     Line of sight2.     Ground propagation3.     Sky propagation4.     Microwaves       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

48 - ________ is a type of transmission impairment in which the signal loses strength dueto the resistance of the transmission medium.

1.     Attenuation2.     Distortion3.     Noise4.     Decibel       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

49 - _________ can impair a signal.

1.     Attenuation2.     Distortion3.     Noise4.     All of the above       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

50 - All of popular Fiber optic connectors are ___________ shaped.

1.     Conical2.     Barrel3.     Circular4.     Rectangular       Correct Choice : 2             From Lectuer # 26

www.vugujranwala.com

51 - ________ is a type of transmission impairment in which the signal loses strength dueto the different propagation speeds of each frequency that makes up the signal.

1.     Attenuation2.     Distortion

page 9 / 41

3.     Noise4.     Decibel       Correct Choice : 2             From Lectuer # 26

www.vugujranwala.com

52 - ________ is a type of transmission impairment in which an outside source such ascrosstalk corrupts a signal.

1.     Attenuation2.     Distortion3.     Noise4.     Decibel       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

53 - In asynchronous transmission, the gap time between bytes is _______.

1.     Fixed2.     A function of the data rate3.     Variable4.     Zero       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

54 - Synchronous transmission does not have _______.

1.     A start bit2.     A stop bit3.     Gaps between bytes4.     All the above       Correct Choice : 4             From Lectuer # 26

www.vugujranwala.com

55 - When a beam of light travels through media of two different densities, if the angle ofincidence is greater than the critical angle, _______ occurs.

1.     Refraction2.     Reflection3.     Incidence4.     Criticism       Correct Choice : 2             From Lectuer # 26

www.vugujranwala.com

56 - Which of the following is not a guided medium?

1.     Twisted-pair cable2.     Fiber-optic cable3.     Atmosphere4.     Coaxial cable       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

57 - Smoke signals are an example of communication through _______.

page 10 / 41

1.     A guided medium2.     A refractive medium3.     An unguided medium4.     A small or large medium       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

58 - Which of the following primarily uses guided media?

1.     Cellular telephone system2.     Satellite communications3.     Local telephone system4.     Radio broadcasting       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

59 - Radio wave and microwave frequencies range from _______.

1.     3 to 300 KHz2.     300 KHz to 3 GHz3.     3 KHz to 300 GHz4.     3 KHz to 3000 GHz       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

60 - When the angle of incidence is _______ the critical angle, the light beam bends alongthe interface.

1.     More than2.     Less than3.     Equal to4.     None of the above       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

61 - Which one is not the function of data link layer?

1.     Line discipline2.     Flow control3.     Error control4.     Network control       Correct Choice : 4             From Lectuer # 26

www.vugujranwala.com

62 - In an optical fiber, the inner core is _______ the cladding.

1.     Less dense than2.     Denser than3.     The same density as4.     Another name for       Correct Choice : 2             From Lectuer # 26

www.vugujranwala.com

63 - ________ is a type of transmission impairment in which the signal loses strength due

page 11 / 41

to the resistance of the transmission medium.

1.     Attenuation2.     Distortion3.     Noise4.     Decibel       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

64 - ________ is a type of transmission impairment in which the signal loses strength dueto the different propagation speeds of each frequency that makes up the signal.

1.     Attenuation2.     Distortion3.     Noise4.     Decibel       Correct Choice : 2             From Lectuer # 26

www.vugujranwala.com

65 - ________ is a type of transmission impairment in which an outside source such ascrosstalk corrupts a signal.

1.     Attenuation2.     Distortion3.     Noise4.     Decibel       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

66 - _________ can impair a signal.

1.     Attenuation2.     Distortion3.     Noise4.     All of the above       Correct Choice : 1             From Lectuer # 26

www.vugujranwala.com

67 - In asynchronous transmission, the gap time between bytes is _______.

1.     Fixed2.     A function of the data rate3.     Variable4.     Zero       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

68 - Synchronous transmission does not have _______.

1.     A start bit2.     A stop bit3.     Gaps between bytes

page 12 / 41

4.     All the above       Correct Choice : 4             From Lectuer # 26

www.vugujranwala.com

69 - Diameter of the core are expressed in

1.     cm2.     micro3.     meters4.     microns       Correct Choice : 4             From Lectuer # 26

www.vugujranwala.com

www.vugujranwala.com

71 - ILD provide

1.     Unfocused light2.     Unfocused light long distance3.     Focused light lon distance4.     Focused light small distance       Correct Choice : 3             From Lectuer # 26

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

77 - Measures the relative strengths of two signals

1.     Decibel2.     Bandwidth3.     Phase4.     Wavelength       Correct Choice : 1             From Lectuer # 27

www.vugujranwala.com

78 - The VLF and LF bands use _______ propagation for communications.

1.     Space2.     Ground3.     Sky4.     Line of sight       Correct Choice : 2             From Lectuer # 27

www.vugujranwala.com

79 - A traditional telephone line has a bandwidth of __________.

1.     4000 Hz

page 13 / 41

2.     2000 Hz3.     2000 MHz4.     4000 MHz       Correct Choice : 4             From Lectuer # 27

www.vugujranwala.com

80 - A parabolic dish antenna is a(n) _______ antenna.

1.     Omnidirectional2.     Bidirectional3.     Horn4.     Unidirectional       Correct Choice : 4             From Lectuer # 27

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

83 - HF use

1.     Line of sight2.     Ionospheric propagation3.     Tronospheric propagation4.     Broad cast       Correct Choice : 2             From Lectuer # 27

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

87 - Each service area is divided into small ranges

1.     packets2.     Cellular teliphony3.     MTSO4.     cells       Correct Choice : 4             From Lectuer # 27

www.vugujranwala.com

88 - Each cell office is controlled by a switching office called

1.     cells2.     MTS3.     cellular telephony4.     Mobile telephone switching office       Correct Choice : 4             From Lectuer # 27

www.vugujranwala.com

www.vugujranwala.com

90 - Negative dB means

page 14 / 41

1.     Impairment2.     Distortion3.     Attenuation4.     amplification       Correct Choice : 3             From Lectuer # 27

www.vugujranwala.com

91 - Positive dB means

1.     Impairment2.     Distortion3.     Attenuation4.     amplification       Correct Choice : 4             From Lectuer # 27

www.vugujranwala.com

92 - Distortion occur in

1.     Signal2.     Sine wave signal3.     Composite signal4.     EM signal       Correct Choice : 3             From Lectuer # 27

www.vugujranwala.com

93 - When propagation speed is multiplied by propagation time, we get the ________.

1.     throughput2.     wavelength of the signal3.     distortion factor4.     distance a signal or bit has traveled       Correct Choice : 4             From Lectuer # 28

www.vugujranwala.com

94 - In fiber optics, the signal source is _______ waves.

1.     Very low-frequency2.     Light3.     Radio4.     Infrared       Correct Choice : 2             From Lectuer # 28

www.vugujranwala.com

95 - When propagation speed is multiplied by propagation time, we get the ________.

1.     throughput2.     wavelength of the signal3.     distortion factor4.     distance a signal or bit has traveled       Correct Choice : 4             From Lectuer # 28

www.vugujranwala.com

www.vugujranwala.com

page 15 / 41

97 - Due to random motion of electron

1.     Thermal noise2.     Induced noise3.     Cross talk4.     Spike       Correct Choice : 1             From Lectuer # 28

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

103 - Data link protocols can be divided into ______________ sub-groups.

1.     Two2.     three3.     four4.     five       Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

104 - Data link protocols can be divided into ______________ sub-groups.

1.     Two2.     three3.     four4.     five       Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

105 - WDM stands for

1.     Wave Division Multiplexing2.     Wrong Division Multiplexing3.     Well Division Multiplexing4.     West Division Multiplexing       Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

106 - In Synchronous TDM, Time slots are not same in number as input devices.

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

page 16 / 41

107 - Multiplexing is the set of techniques that allows simultaneous TX of multiple signalsacross a ___________ data link

1.     Single2.     Double3.     Multi4.     None of the given       Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

108 - There are ________ basic categories of multiplexing.

1.     32.     43.     24.     5       Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

109 - WDM(wave division multiplexing) deals with

1.     electric waves2.     light waves3.     both4.            Correct Choice : 2             From Lectuer # 29

www.vugujranwala.com

110 - Which one is not the function of data link layer?

1.     Flow control2.     Error control3.     Network control4.     Line discipline       Correct Choice : 2             From Lectuer # 29

www.vugujranwala.com

111 - Which of the following techniques takes data from one high speed line and breaks itinto portions?

1.     Inverse subtraction2.     Inverse addition3.     Multiplexing4.     Inverse multiplexing       Correct Choice : 3             From Lectuer # 29

www.vugujranwala.com

112 - Time slots are dynamically allotted in _______________TDM technique.

1.     FDM2.     Asynchronous3.     WDM

page 17 / 41

4.     Synchronous       Correct Choice : 4             From Lectuer # 29

www.vugujranwala.com

113 - A prism can deflect the light depending upon the angle of ____________ and thefrequency.

1.     Deviation2.     Incident3.     Refraction4.     Reflection       Correct Choice : 4             From Lectuer # 29

www.vugujranwala.com

www.vugujranwala.com

115 - Data convert parrallel to series form, is the example of

1.     Multiplexing2.     Demultiplexing3.     FDM4.     TDM       Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

116 - MUX allocates exactly the same time slot to each device at all device whether or notthe device has any thing to transmit

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 29

www.vugujranwala.com

117 - Interleaving concept use in case of

1.     FDM2.     TDM3.     WDM4.     Synchronous       Correct Choice : 2             From Lectuer # 29

www.vugujranwala.com

118 - Prism can deflect the light depending upon the

1.     Angle of refraction2.     angle of incidence3.     Critical angle4.     both a and c       Correct Choice : 2             From Lectuer # 29

www.vugujranwala.com

119 - Inteleaving can done by

page 18 / 41

1.     Bits2.     Bytes3.     other data unit4.     all of these       Correct Choice : 4             From Lectuer # 29

www.vugujranwala.com

www.vugujranwala.com

121 - Which multiplexing technique shifts each signal to a different carrier frequency?

1.     FDM2.     Synchronous TDM3.     Asynchronous TDM4.     None of the Above       Correct Choice : 4             From Lectuer # 30

www.vugujranwala.com

122 - Multiplexing has long been used as an essential tool in ______.

1.     Electronic industry2.     Telephone industry3.     Space science4.     VLAN       Correct Choice : 2             From Lectuer # 30

www.vugujranwala.com

123 - Asynchronous TDM is efficient only when the size of the time slot is kept relatively________

1.     Large2.     Medium3.     Zero4.     Small       Correct Choice : 2             From Lectuer # 30

www.vugujranwala.com

124 - Telephone network is an example of a __________ network.

1.     Packet-switched2.     Circuit-switched3.     Message-switched4.     Tele-switched       Correct Choice : 4             From Lectuer # 30

www.vugujranwala.com

www.vugujranwala.com

126 - Asynchronous means

1.     flexible2.     fixed3.     Unstatistical

page 19 / 41

4.     both b and c       Correct Choice : 1             From Lectuer # 30

www.vugujranwala.com

127 - Need for addressing makes asynchronous TDM inefficient for bit or byte interleaving

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 30

www.vugujranwala.com

128 - Asynchronous TDM is efficient only

1.     when the size of the time slot is kept relativly large2.     when the size of the timeslot is kept relativly small3.     when the number of input are greater4.     when the numberof input are smaller       Correct Choice : 1             From Lectuer # 30

www.vugujranwala.com

129 - Telephone system application of

1.     Asynchronous TDM2.     Synchronous TDM3.     Multiplexing4.     Inverse Multiplexing       Correct Choice : 3             From Lectuer # 30

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

132 - Digital services are less sensitive than analog ones

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 31

www.vugujranwala.com

133 - Switched/56 service is already digital. Subcribers do not need modems they need

1.     DDS2.     DS3.     USD4.     DSU       Correct Choice : 4             From Lectuer # 31

www.vugujranwala.com

134 - DDS provide Max. date rate of

page 20 / 41

1.     56kbps2.     64kbps3.     33 kbps4.     168 kbps       Correct Choice : 2             From Lectuer # 31

www.vugujranwala.com

135 - DS is a hierarchy of

1.     FDM2.     TDM3.     Analog signal4.     Digital signal       Correct Choice : 4             From Lectuer # 31

www.vugujranwala.com

136 - Error control is both error _________ and error ___________

1.     detection; correction2.     detection; deletion3.     detection; avoidance4.     detection; forwarding       Correct Choice : 1             From Lectuer # 32

www.vugujranwala.com

137 - ______ Control refers to methods of error detection and correction?

1.     Flow2.     Error3.     Transmission4.     none of the above       Correct Choice : 2             From Lectuer # 32

www.vugujranwala.com

138 - T Lines are ___________ lines designed for digital data

1.     Analog2.     Digital3.     Composite4.     Telephone       Correct Choice : 2             From Lectuer # 32

www.vugujranwala.com

139 - Europeans use a version of T-lines called _________

1.     F-lines2.     E-lines3.     D-lines4.     S-lines       Correct Choice : 2             From Lectuer # 32

www.vugujranwala.com

140 - FTTC stands for _____________

page 21 / 41

1.     flexible to the curb2.     fiber to the curb3.     fiber to the cable4.     fiber to the center       Correct Choice : 2             From Lectuer # 32

www.vugujranwala.com

141 - FTTC can be implemented in ______________.

1.     Telephone system2.     Cable System3.     Telephone and Cable System4.     Non of the above       Correct Choice : 3             From Lectuer # 32

www.vugujranwala.com

142 - FTTC stands for ___________

1.     fiber to the center2.     fiber to the cable3.     fiber to the curb4.     flexible to the curb       Correct Choice : 3             From Lectuer # 32

www.vugujranwala.com

143 - Which error detection method consists of a parity bit for each data unit as well as anentire data unit of parity bits?

1.     Simple parity check2.     Checksum3.     Two-dimensional parity check4.     CRC       Correct Choice : 3             From Lectuer # 32

www.vugujranwala.com

www.vugujranwala.com

145 - Error detection and correction is implemented

1.     Data link layer2.     Transport layer3.     network layer4.     both a and b       Correct Choice : 4             From Lectuer # 32

www.vugujranwala.com

146 - Which error detection method consists of just one redundant bit per data unit?

1.     Simple parity check2.     Two-dimensional parity check3.     CRC4.     Checksum       Correct Choice : 1             From Lectuer # 33

page 22 / 41

www.vugujranwala.com

147 - Which error detection method can detect a single-bit error?

1.     Simple parity check2.     Two-dimensional parity check3.     CRC4.     All of the given       Correct Choice : 1             From Lectuer # 33

www.vugujranwala.com

148 - Which error detection method consists of just one redundant bit per data unit?

1.     Two-dimensional parity check2.     CRC3.     Simple parity check4.     Checksum       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

149 - Burst error is easily corrected then single bit error.

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 33

www.vugujranwala.com

150 - Which of the following best describes a single-bit error?

1.     A single bit is inverted2.     A single bit is inverted per transmission3.     A single bit is inverted per data unit4.     Any of the above       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

151 - Which error detection method involves polynomials?

1.     CRC2.     Simple parity check3.     Two-dimensional parity check4.     Checksum       Correct Choice : 1             From Lectuer # 33

www.vugujranwala.com

152 - In cyclic redundancy checking, what is the CRC?

1.     The remainder2.     The divisor3.     The quotient4.     The dividend       Correct Choice : 1             From Lectuer # 33

page 23 / 41

www.vugujranwala.com

153 - In CRC there is no error if the if the remainder at the receiver is

1.     Equal to the Remainder of the sender2.     Zero3.     Non Zero4.     The quotient at the sender       Correct Choice : 2             From Lectuer # 33

www.vugujranwala.com

154 - In cyclic redundancy checking, the divisor is _______ the CRC.

1.     The same size as2.     1 bit more than3.     1 bit less than4.     2 bits more than       Correct Choice : 2             From Lectuer # 33

www.vugujranwala.com

155 - At the CRC checker, _______ means that the data unit is damaged.

1.     A string of alternating 1s and 0s2.     A nonzero remainder3.     A string of 0s4.     A string of 1s       Correct Choice : 2             From Lectuer # 33

www.vugujranwala.com

156 - If the ASCII character G is sent and the character D is received, what type of error isthis?

1.     Single-bit2.     Multiple-bit3.     Burst4.     Recoverable       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

157 - If the ASCII character H is sent and the character I is received, what type of error isthis?

1.     Burst2.     Recoverable3.     Single-bit4.     Multiple-bit       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

158 - If the data unit is 111111, the divisor 1010, and the remainder 110, what is thedividend at the receiver?

1.     1111110112.     1010110

page 24 / 41

3.     1111111104.     110111111       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

159 - At the CRC generator, _______ added to the data unit after the division process.

1.     0s are2.     1s are3.     The CRC remainder is4.     The polynomial is       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

160 - At the CRC generator, _______ added to the data unit before the division process.

1.     A polynomial is2.     A CRC remainder is3.     0s are4.     1s are       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

161 - If the ASCII character G is sent and the character D is received, what type of error isthis?

1.     Single-bit2.     Multiple-bit3.     Burst4.     Recoverable       Correct Choice : 3             From Lectuer # 33

www.vugujranwala.com

162 - If the data unit is 111111 and the devisor is 1010, what is dividend at the transmitter?

1.     1111110002.     11111100003.     1111114.     1111111010       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

163 - Given a 10-bit sequence 1010011110 and a divisor of 1011, CRC will be

1.     0012.     0003.     1004.     101       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

164 - How does the CRC checker know that the received data unit is undamaged?

page 25 / 41

1.     The CRC checker divides the received data by the predetermined divisor andaccepts the data if the quotient is zero2.     The CRC checker divides the received data by the predetermined divisor andaccepts the data if the remainder is one3.     The CRC checker divides the received data by the predetermined divisor andaccepts the data if the remainder is less than zero4.     The CRC checker divides the received data by the predetermined divisor andaccepts the data if the remainder is zero       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

165 - At the CRC checker, ________ means that the data unit is damaged.

1.     A string of 0s2.     A string of 1s3.     A string of alternating 1s and 0s4.     A nonzero remainder       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

166 - Which error detection method involves the use of parity bits?

1.     Simple parity check2.     Two-dimensional parity check3.     CRC4.     (a) and (b)       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

167 - If odd parity is used for ASCII error detection, the number of 0s per 8-bit symbol is_______.

1.     Indeterminate2.     423.     Even4.     Odd       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

168 - Which error detection method can detect a burst error?

1.     The parity check2.     Two-dimensional parity check3.     CRC4.     (b) and (c)       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

www.vugujranwala.com

170 - Single bit error occur if we are sending data using

1.     Parallel TX

page 26 / 41

2.     Serial TX3.     Packet4.     Frame       Correct Choice : 1             From Lectuer # 33

www.vugujranwala.com

171 - Burst error mean

1.     two or more bit sign the data unit have changed from 0 to 1 or from 1 to 02.     Multiple bits are changed3.     Does not necessarily mean that error occur in consecutive bit4.     all of these       Correct Choice : 4             From Lectuer # 33

www.vugujranwala.com

www.vugujranwala.com

173 - it can not detect errors if the total number of error is even

1.     VRC2.     LRC3.     Redundancy4.     both a and b       Correct Choice : 1             From Lectuer # 33

www.vugujranwala.com

www.vugujranwala.com

175 - Which erroe dectetion method involves polynomials?

1.     Simple parity check2.     Two-dimensional parity check3.     CRC4.     Checksum       Correct Choice : 3             From Lectuer # 34

www.vugujranwala.com

176 - Which error detection method can detect a single-bit error?

1.     Simple parity check2.     Two-dimensional parity check3.     CRC4.     All the above       Correct Choice : 4             From Lectuer # 34

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

179 - The checksum of 0000 and 0000 is __________

1.     11112.     0

page 27 / 41

3.     11104.     111       Correct Choice : 1             From Lectuer # 35

www.vugujranwala.com

180 - Which error detection method uses ones complement arithmetic?

1.     Simple parity check2.     Two-Dimensional parity check3.     CRC4.     Checksum       Correct Choice : 4             From Lectuer # 35

www.vugujranwala.com

181 - Which error detection method uses ones complement arithmetic?

1.     Simple parity check2.     Two-dimensional parity check3.     CRC4.     Checksum       Correct Choice : 4             From Lectuer # 35

www.vugujranwala.com

182 - The sum of the checksum and data at the receiver is _______ if there are no errors.

1.     -02.     +03.     The complement of the checksum4.     The complement of the data       Correct Choice : 1             From Lectuer # 35

www.vugujranwala.com

183 - Which of the following best describes a single-bit error?

1.     A single bit is inverted2.     A single bit is inverted per data unit3.     A single bit is inverted per transmission4.     None of the given       Correct Choice : 2             From Lectuer # 35

www.vugujranwala.com

184 - Which error detection method uses ones complement arithmetic?

1.     Simple parity check2.     Checksum3.     Two-dimensional parity check4.     CRC       Correct Choice : 2             From Lectuer # 35

www.vugujranwala.com

185 - Which of the following best describes a single-bit error?

1.     A single bit is inverted.2.     A single bit is inverted per transmission

page 28 / 41

3.     A single bit is inverted per data unit.4.     Any of the above       Correct Choice : 3             From Lectuer # 35

www.vugujranwala.com

186 - The Hamming code is a method of _______.

1.     Error detection2.     Error correction3.     Error encapsulation4.     (a) and (b)       Correct Choice : 4             From Lectuer # 35

www.vugujranwala.com

www.vugujranwala.com

188 - which option better explain the concept of checksum

1.     one pattern remain elusive2.     Detects most error involving on even number of bits3.     Detects all error involving an odd number of bits4.     all if these       Correct Choice : 4             From Lectuer # 35

www.vugujranwala.com

189 - if a bit inversion is balanced by an opposite bit inversion in the corresponding digitalof another segment

1.     Error is dedected2.     Error is Undedected3.     Checksum error occur4.     CRC error occur       Correct Choice : 2             From Lectuer # 35

www.vugujranwala.com

190 - Error correction can be done if

1.     Receiver can ask sender for re TX2.     Receiver can use an error detecting code which automatically correct certainerror3.     Receiver can use an error correcting code4.     both a and b       Correct Choice : 4             From Lectuer # 35

www.vugujranwala.com

191 - In data link layer, communication requires at least ___________ devices workingtogether

1.     32.     23.     44.     5       Correct Choice : 2             From Lectuer # 36

page 29 / 41

www.vugujranwala.com

192 - Data link control is composed of ____________ important functions.

1.     22.     33.     44.     5       Correct Choice : 2             From Lectuer # 36

www.vugujranwala.com

www.vugujranwala.com

194 - Coordination of half duplex TX is a part pf a procedure called

1.     Line discipline2.     Flow control3.     Error control4.     all of these       Correct Choice : 1             From Lectuer # 36

www.vugujranwala.com

195 - Amount of data that can be sent before the receiving acknowledgment

1.     Line discipline2.     Flow control3.     Error control4.     all of these       Correct Choice : 2             From Lectuer # 36

www.vugujranwala.com

196 - Coordinates the link systems, which device can send and when, it can send?

1.     Line discipline2.     Flow control3.     Error control4.     all of these       Correct Choice : 1             From Lectuer # 36

www.vugujranwala.com

197 - Line discipline function of data link layer oversea

1.     The establishment of devices2.     Sight of a particular device to transmit a given time3.     full duplex4.     botha and c       Correct Choice : 2             From Lectuer # 36

www.vugujranwala.com

198 - If the primary wants to receive data, it asks the second-arise if they have anything tosend, this is called

1.     POLLING2.     SELECTING

page 30 / 41

3.     None SELECTING4.     None Polling       Correct Choice : 1             From Lectuer # 37

www.vugujranwala.com

199 - ENQ/ACK stands for______________

1.     Enquiry/ Acknowledgment2.     Enque/ Acknowledgment3.     Enquist/ Acknowledgment4.     none of the given       Correct Choice : 1             From Lectuer # 37

www.vugujranwala.com

200 - Flow control is needed to prevent ____________

1.     Bit errors2.     Overflow of the sender buffer3.     Overflow of the receiver buffer4.     Collision between sender and receiver       Correct Choice : 3             From Lectuer # 37

www.vugujranwala.com

201 - For point-to-point configuration, addressing is needed

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 37

www.vugujranwala.com

202 - For point-to-point configuration, addressing is needed

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 37

www.vugujranwala.com

203 - A timer is set when ___________ is (are) sent out.

1.     A data frame2.     An ACK3.     A NAK4.     All of given       Correct Choice : 2             From Lectuer # 37

www.vugujranwala.com

204 - Flow Control is the responsibility of _________

1.     Network Layer2.     Transport Layer

page 31 / 41

3.     Data Link Layer4.     Physical Layer       Correct Choice : 3             From Lectuer # 37

www.vugujranwala.com

205 - If a T-1 carries 8000 frames, then data rate will be ___________

1.     2.544 Mbps2.     1.544 Mbps3.     1.544 kbps4.     1.544 Gbps       Correct Choice : 2             From Lectuer # 37

www.vugujranwala.com

206 - if the primary wants to recive data, it asks the second arise of they have anything tosend called

1.     Selecting2.     Polling3.     Half duplex4.     Full duplex       Correct Choice : 2             From Lectuer # 37

www.vugujranwala.com

207 - if the primary want to send data, it tells the largest, secondary to get ready to receivecalled

1.     Selecting2.     Polling3.     Half duplex4.     Full duplex       Correct Choice : 1             From Lectuer # 37

www.vugujranwala.com

208 - For stop-and-wait ARQ, for n data packets sent, ___________ acknowledgments areneeded.

1.     n2.     2n3.     N-14.     N+1       Correct Choice : 1             From Lectuer # 38

www.vugujranwala.com

209 - In the _____ Protocol, the sender sends one frame, stops until it receivesconfirmation from the receiver, and then sends the next frame?

1.     Stop-and-Wait2.     Simplest3.     Go-Back-N ARQ4.     Selective-Repeat ARQ       Correct Choice : 1             From Lectuer # 38

www.vugujranwala.com

page 32 / 41

210 - Flow control is needed to prevent ____________.

1.     Collision between sender and receiver2.     Overflow of the receiver buffer3.     Overflow of the sender buffer4.     Bit errors       Correct Choice : 2             From Lectuer # 38

www.vugujranwala.com

211 - For a sliding window of size n-1 (n sequence numbers), there can be a maximum of__________ frames sent but unacknowledged.

1.     02.     N-13.     N4.     N+1       Correct Choice : 2             From Lectuer # 38

www.vugujranwala.com

212 - ARQ stands for ___________

1.     Automatic repeat quantization2.     Automatic repeat request3.     Automatic retransmission request4.     Acknowledge repeat request.       Correct Choice : 2             From Lectuer # 38

www.vugujranwala.com

213 - In __________ ARQ, if a NAK is received, only the specific damaged or lost frame isretransmitted.

1.     Stop and Wait2.     Go-Back-N3.     Selective repeat4.     Stop-and-wait & Go-back-N       Correct Choice : 3             From Lectuer # 38

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

216 - In sliding window, frames are numbered module n mean from 0 to

1.     n2.     n - 13.     n+ 14.     2n       Correct Choice : 2             From Lectuer # 38

www.vugujranwala.com

www.vugujranwala.com

218 - Frame can be lost in tranmit if

page 33 / 41

1.     Lost data frame2.     lost ACK frame3.     Lost NAK frame4.     all of these       Correct Choice : 4             From Lectuer # 38

www.vugujranwala.com

219 - XMODEM is a ______________ protocol designed for telephone-line communicationb/w PCs.

1.     File transfer2.     hardware3.     software4.     application exchange       Correct Choice : 1             From Lectuer # 39

www.vugujranwala.com

220 - Sliding window requires that data frames be transmitted _______________

1.     Sequentially2.     Frequently3.     Synchronously4.     Asynchronously       Correct Choice : 1             From Lectuer # 39

www.vugujranwala.com

221 - In __________ ARQ, if a NAK is received, only the specific damaged or lost frame isretransmitted.

1.     Stop-and-wait2.     Go-Back-N3.     Selective reject4.     Stop-and-wait & Go-back-N       Correct Choice : 3             From Lectuer # 39

www.vugujranwala.com

www.vugujranwala.com

223 - In synchronous protocols

1.     Treat each char ina a bit stream dependently2.     Treat each char ina a bit stream independently3.     traet the whole bit stream and chop it into char of equal size4.     both b and c       Correct Choice : 3             From Lectuer # 39

www.vugujranwala.com

www.vugujranwala.com

225 - Control frames from the receiver

1.     ACK2.     NAK

page 34 / 41

3.     CAN4.     all of these       Correct Choice : 4             From Lectuer # 39

www.vugujranwala.com

226 - In X Modem

1.     One CANs to abort transmission2.     Two CANs to abort transmission3.     Multiple files can be sent simultaneously4.     both b and c       Correct Choice : 1             From Lectuer # 39

www.vugujranwala.com

227 - BLAST stands for :

1.     Blocked synchronous transmission2.     Barrel asynchronous transmission3.     Below asynchronous transmission4.     Blocked asynchronous transmission       Correct Choice : 4             From Lectuer # 40

www.vugujranwala.com

228 - Which of the following combines features of the other two.

1.     ZMODEM2.     YMODEM3.     XMODEM4.     None of given       Correct Choice : 1             From Lectuer # 40

www.vugujranwala.com

229 - The HDLC ___________ field defines the beginning and end of a frame.

1.     Flag2.     Address3.     Control4.     FCS       Correct Choice : 1             From Lectuer # 40

www.vugujranwala.com

230 - The shortest frame in HDLC protocol is usually the _________ frame.

1.     Supervisory2.     Management3.     Information4.     None of the given       Correct Choice : 1             From Lectuer # 40

www.vugujranwala.com

231 - In Y Modem

1.     Multiple files can be sent simultaneously2.     Two CANs to abort transmission

page 35 / 41

3.     ITU-T CRC 16 for error checking4.     all of these       Correct Choice : 4             From Lectuer # 40

www.vugujranwala.com

232 - Protocols interpret a transmission frame or packet are succession of characters eachusually compared of one byte

1.     Byte Criented protocols2.     Bit oriented protocol3.     BSC4.     both a nd b       Correct Choice : 1             From Lectuer # 40

www.vugujranwala.com

233 - BSC developed by IB in

1.     19602.     19643.     19684.     1970       Correct Choice : 2             From Lectuer # 40

www.vugujranwala.com

234 - BSc is

1.     Usable in point to point2.     Usable in multiple communication3.     Half duplex4.     all of these       Correct Choice : 4             From Lectuer # 40

www.vugujranwala.com

235 - if a fram is used stricly for control purpose called

1.     Data purpose2.     Data control purpose3.     Control purpose4.     bsc frame control       Correct Choice : 3             From Lectuer # 40

www.vugujranwala.com

www.vugujranwala.com

237 - multi block frame

1.     increase the likelihood of error detection2.     text in a message is often divided b/w several block3.     Several frames can carry continuation of single message4.     all of these       Correct Choice : 4             From Lectuer # 40

www.vugujranwala.com

www.vugujranwala.com

page 36 / 41

239 - Shortest frame in HDLC protocols is usually the ____ frame.

1.     Information2.     Supervisory3.     Management4.     None of the above       Correct Choice : 4             From Lectuer # 41

www.vugujranwala.com

www.vugujranwala.com

241 - Characterestic of HDLC is

1.     Full duplex2.     Point to pint3.     Configaration4.     all of these       Correct Choice : 3             From Lectuer # 41

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

247 - The ending flag of 1 frame can not be used as the bedinning flag of the next frame

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 41

www.vugujranwala.com

www.vugujranwala.com

249 - The PDU has no flag fields, no CRC, and no station address

1.     TRUE2.     FALSE3.     4.            Correct Choice : 1             From Lectuer # 42

www.vugujranwala.com

250 - The DSAP and SSAP are addresses used by ____to identify the protocol stack.

1.     Network2.     MAC

page 37 / 41

3.     LLC4.     None of the above       Correct Choice : 2             From Lectuer # 42

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

259 - A device listens to the line before it transmit

1.     Multiple Access2.     Carrier Sense3.     Collision Setection4.     all of these       Correct Choice : 2             From Lectuer # 42

www.vugujranwala.com

www.vugujranwala.com

261 - Ethernet LAN can support data rates between

1.     1 to 100 kbps2.     1 to 100 Mbps3.     100 to 1000kbps4.     100 to 1000Mbps       Correct Choice : 2             From Lectuer # 42

www.vugujranwala.com

www.vugujranwala.com

263 - In 10 base 2

1.     No AUI cables are needed2.     RG 83.     BNC4.     all of these       Correct Choice : 1             From Lectuer # 43

www.vugujranwala.com

www.vugujranwala.com

265 - Switched ethernet use an attempt to improve the perpormance of

page 38 / 41

1.     100 base FX2.     100 base TX3.     10 base T4.     10 base T4       Correct Choice : 3             From Lectuer # 43

www.vugujranwala.com

266 - In FDDI, THT stands for:

1.     Token Hash Timer2.     Tier Holding Timer3.     Target Holding Timer4.     Token Holding Timer       Correct Choice : 4             From Lectuer # 44

www.vugujranwala.com

267 - Acces control of token ring

1.     Priority2.     reservation3.     time limits4.     all of these       Correct Choice : 4             From Lectuer # 44

www.vugujranwala.com

268 - FDDI standardized by

1.     ANSI2.     ITU-T3.     IEEE4.     both a and b       Correct Choice : 4             From Lectuer # 44

www.vugujranwala.com

269 - In FDDI timers, which timers incrementing

1.     THT2.     TRT3.     TTRT4.     AMT       Correct Choice : 2             From Lectuer # 44

www.vugujranwala.com

270 - In FDDI timers, which timers decrementing

1.     TRT2.     TTRT3.     THT4.     AMT       Correct Choice : 3             From Lectuer # 44

www.vugujranwala.com

www.vugujranwala.com

page 39 / 41

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

275 - Bridges can divide a large ________ into smaller segments

1.     Network2.     Packet3.     Frame4.     Address       Correct Choice : 1             From Lectuer # 45

www.vugujranwala.com

276 - Repeater is an amplifier, not a regenerator.

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 45

www.vugujranwala.com

277 - Repeaters work on the ____Layer/Layers

1.     Data Link2.     Physical3.     LLC4.     None of the above       Correct Choice : 2             From Lectuer # 45

www.vugujranwala.com

278 - On the transport layer of TCP/IP suit_____ protocols are used

1.     TCP & IP2.     TCP & UDP3.     IP4.     TCp       Correct Choice : 2             From Lectuer # 45

www.vugujranwala.com

279 - A Repeater does not allow us to extend the physical length of network

1.     TRUE2.     FALSE3.     4.            Correct Choice : 2             From Lectuer # 45

www.vugujranwala.com

280 - Application layer of TCP/IP suit is equivalent of _____layers of OSI Model

1.     Application, Presentation and Transport2.     Application, Session and Transport

page 40 / 41

3.     Application, Presentation and Session4.     None of the above       Correct Choice : 3             From Lectuer # 45

www.vugujranwala.com

281 - Bridge is _____ Layer Device

1.     Data Link2.     Physical3.     Network4.     None of the above       Correct Choice : 1             From Lectuer # 45

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

www.vugujranwala.com

Powered by TCPDF (www.tcpdf.org)

page 41 / 41