Architectural Door Accessories - Dugmore Duncan · 2020-01-24 · hinges. ...
McKINNEY Builder’s Hardware Catalog #4 - Dugmore
Transcript of McKINNEY Builder’s Hardware Catalog #4 - Dugmore
McKINNEY Hinge Catalog
An ASSA ABLOY Group company An ASSA ABLOY Group company
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - 23Hinge Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Knuckle Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Hinge Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 14Reference Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 - 17Hand of Doors and Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Hinge Swaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Screws and Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21Finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 - 23
Full Mortise Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 - 39Full Mortise Plain Bearing Hinges - Two Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . .25Full Mortise Bearing Hinges - Two Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .26Full Mortise Bearing Hinges - Two Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Full Mortise Plain Bearing Hinges - Three Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . .28Full Mortise Bearing Hinges - Three Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . .29Full Mortise Bearing Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .30Full Mortise Institutional Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . .31Swing Clear Full Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . .32Full Mortise Plain Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . .33Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .34Wide Throw Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . .35Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Wide Throw Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . .37Swing Clear Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . .38Swing Clear Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . . .39
Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41Standard Duty Center Hung Jamb Mount Pivot Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Full Mortise Anchor Hinge Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 - 46
Half Mortise Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 - 53Half Mortise Plain Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . .47Half Mortise Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . . . .48Half Mortise Bearing Hinges - Three Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . .49Half Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . .50Half Mortise Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . . . .51Swing Clear Half Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . .52Swing Clear Half Mortise Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . .53
Half Surface Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 - 61Half Surface Bearing Hinges - Three Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . .55Half Surface Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . . .56Half Surface Plain Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . .57Half Surface Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . . . .58Half Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . . . .59Swing Clear Half Surface Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . .60Swing Clear Half Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . .61
Full Surface Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 - 68Full Surface Bearing Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .63Full Surface Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .64Full Surface Bearing Hinges - Three Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . .65Full Surface Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .66Full Surface Swing Clear Bearing Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . .67Full Surface Swing Clear Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . .68
Table of Contents Page #
Ap
ril2
003
McKINNEY Hinge Catalog
1An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
006
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Spring Hinges & Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 - 82Full Mortise Single Acting Standard Weight Spring Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69Full Mortise Single Acting Standard Weight Spring Hinge Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70Half Surface Single Acting Standard Weight Spring Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71Heavy Duty Double Acting Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72Heavy Duty Spring Steel Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Heavy Duty Adjustable Tension Simplex Half Surface Double Acting Door Spring . . . . . . . . . . . . . .74Simplex Full Mortise Double Acting Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 - 77Simplex Double Acting Clamp Flange Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78Simplex Half Surface Double Acting Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79Ajax Double Acting Horizontal Spring Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80Sagless Double Acting Gate Spring Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81Lightweight Double Acting Gravity Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Miscellaneous Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 - 86Hinge Back Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83Combination Strike and Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84Emergency Door Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85Double Lipped Strike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Specialty Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 - 98Electrolynx Hinge (QC Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Concealed Circuit Electric Hinge (CC Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88Concealed Switch Electric Hinge (CS Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89Magnetic Monitoring Hinge (MM Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90Junction Box for Electric Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91Pocket Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92Standard Weight Loose Pin Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93Full Mortise Five Knuckle Plain Bearing Light Weight Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94Olive Knuckle Full Mortise Standard Weight Bearing Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95Raised Barrel Full Mortise Standard and Heavy Weight Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96Slip In Full Mortise Type I and Type II Standard Weight Bearing Hinges . . . . . . . . . . . . . . . . . . . . . .97Full Mortise Interim Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Aluminum Continuous Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 - 105Full Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99, 100, 101, 105Full Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102, 103Half Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104Aluminum Continuous Hinge Clearance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Stainless Continuous Hinges and Edge Guards . . . . . . . . . . . . . . . . . . . .106-112Full Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106, 107. 108Half Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109, 110Swing Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111Full Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112300 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Stainless and Steel Continuous Hinge Clearance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Steel Continuous Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113-119Full Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113Full Mortise, Full-Wrap Edge Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114Full Mortise, Half-Wrap Edge Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115Half Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116Half Mortise, Half-Wrap Edge Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117Swing Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118Full Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iNumerical Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover
Discontinued
Discontinued, refer to Architectural Hardware Trim,Protection Plates & Devices Section
McKINNEY Hinge Catalog
2 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
McKINNEY, Your Source For Hinges
McKINNEY Products Companyprovides the non-residentialconstruction industry with a full rangeof commercial door hinges for everyneed. The information in this catalogwill assist you in choosing the hingesthat fully satisfy your design andengineering requirements.Quality And Innovation For MoreThan 100 Years
McKINNEY Products Companyhas been a leader in the design andmanufacture of quality builder’shardware since 1865. McKINNEY is asubsidiary of ASSA ABLOY. TheASSA ABLOY Group is the world'sleading manufacturer and supplier oflocking solutions, dedicated tosatisfying end-user needs for security,safety and convenience.
From its220,000square footplant inScranton,Pennsylvania, McKINNEYproduces a full line of commercial doorhinges in a variety of finishes, bearingsand functions for all interior orexterior applications. AmongMcKINNEY’s many innovations wasthe oil impregnated bearing whichgreatly improved the performance ofbearing hinges. To meet today’s needfor greater security applications,McKINNEY developed a variety ofelectric hinges used in remote doormonitoring and access control systems.Quality, performance
and the ability to meet critical
construction deadlines havemade McKINNEY hinges a first
choice for construction projectsworldwide. Hinge Solutions For Every Design Need
McKINNEY hinges and other doorhanging hardware provide solutions forthe most highly specialized functionsas well as decorative requirements. The broad line and exceptional quality ensure getting exactly the right product for your new or retrofitconstruction projects.
“McKINNEY iscomprised of a worldclass team of highlyskilled people focusedon exceeding customerneeds throughinnovation andflexibility in themanufacture ofarchitectural buildingproducts.”
McKINNEY Hinge CatalogHinge Types
3An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
04
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
McKINNEY offers the broadest rangeof full mortise hinges in a variety ofmetals, finishes, sizes, and weights tomeet all your load bearing and securityapplications. They include two, three,and five knuckle styles, swing clearhinges, wide throw hinges, anchorhinges, electric hinges, institutionalhinges, and pivots.
McKinney hinges conform toGovernment standards CS9-65 andSDI as well as the following standardsapproved by the Builders hardwareManufacturers / American NationalStandards Institute:ANSI/BHMA Standard 156.1 - TheAmerican National Standard for Buttsand Hinges
Available in a choice of metals, gauges,and sizes for a wide range of doorthicknesses. You may specify plainbearing, standard weight bearing, orheavy weight bearing models. Regularand swing clear applications. Twoknuckle, three knuckle, as well as fiveknuckle styles are available.
Choose from regular and swing clearmodels for heavy weight bearing orstandard weight bearing applications ina choice of metals, gauges, and sizes.Two knuckle, three knuckle, and fiveknuckle styles are available.
Heavy weight bearing, standard weightbearing, and plain bearing hinges in arange of metals, gauges, and sizes.Regular and swing clear applications.Two knuckle, three knuckle, and fiveknuckle styles
A full range of spring hinges areavailable for all types of door sizes,weights, and applications. Included arefull mortise single acting hinges, singleacting reverse spring hinges, full mortisedouble acting hinges, and half surfacedouble acting hinges, plus our heavy dutyspring butt hinge that permits doors toopen 90˚ in either direction. In addition,McKINNEY produces a variety of hingesfor special applications including anchorhinges, wide throw hinges, swing clearhinges, and pocket hinges.
McKINNEY self-aligning continuoushinges extend the full height of thedoor. These hinges bond the door andframe into an integrated unit andpresent a streamlined, no-gap surface,affording privacy, safety, andoutstanding performance. The highload capacity of these hinges makesthem ideal for use in high-frequencyareas where hinges are subject to abuse.The hinge design affords resistance tovandalism. McKINNEY continuousgeared hinges are warranted for the lifeof the building. UL listed in both theUSA and Canada up to 3 hour (Alabel) application. These hinges areavailable in aluminum, stainless andsteel.
McKINNEY produces an assortment ofelectrical security hinges for a widevariety of control functions. Includedare full mortise bearing hinges witheither concealed circuitry or concealedswitch. In addition, a unique, field-replaceable magnet monitoring hinge,featuring a magnetic reed concealedswitch, is available. McKINNEY alsoproduces full mortise institutionalhinges for maximum security installations,and our full mortise single acting springhinge is available with a TamperResistant Screw (TRS Option) whichis screwed into the tension ratchet afterproper tension has been set.
McKINNEY provides a standard dutycenter hung jamb mount pivot set.
Additionally, we provide emergency door stops, strikes, and stainless steeledge guards.
The most up to date Templatesare available on our website @www.mckinneyhinge.com
McKINNEY offers the broadest rangeof full mortise hinges in a variety ofmetals, finishes, sizes, and weights tomeet all your load bearing and securityapplications. They include two, three,and five knuckle styles, swing clearhinges, wide throw hinges, anchorhinges, electric hinges, institutionalhinges, and pivots.
Full Mortise Hinges Half Mortise Hinges Continuous Hinges
Half Surface Hinges
Spring and Specialty HingesSecurity Hinges Misc.
Full Surface Hinges
ANSI/BHMA Standard 156.7 - TheAmerican National Standard forTemplate Hinge DimensionsANSI/BHMA Standard 156.17 - TheAmerican National Standard for Self-Closing Hinges & PivotsANSI/BHMA Standard 156.18 - TheAmerican National Standard forMaterial and Finishes
McKINNEY Hinge CatalogBearings
4 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
This is the designation for non-bearing hinges. Knuckles aremachined with bearing-like surfaces to move against one another. These arenot recommended for high frequencydoors or doors with closing devices.These hinges are not approved for usein labeled openings. An anti-frictioncomponent is provided on allMcKINNEY three knuckle and Moderne (two knuckle) plainbearing hinges.
Ball bearings are available on all fiveknuckle bearing hinges.
These are furnished only uponwritten request to the factory statingthat all bearings are to be ball bearings.Standard on institutional hinges, andall hinges over 6".
One piece, non-ferrous, and self-lubricating bearings ensure evenlonger-lasting wear and resistance toclogging, corrosion, and hinge failure.This feature is standard and supplied onall five knuckle bearing hinges.
Concealed, anti-friction type bearingsare available on all five knucklebearing hinges, which provide long-lasting wear and consistency of hingebarrel design.
Note: All three and two knuckle bearing hingesare provided with concealed, anti-friction typebearings (designated TA).
Standard gauge McKINNEY threeknuckle and five knuckle bearinghinges (.123 - .160) are supplied with two bearings. These hinges areintended for use on doors subjected to average traffic in residential andlight commercial construction. Four bearings can be specified(T4A2714/T4A2314) on some five knuckle hinges.
Heavy gauge McKINNEY hinges(.180 - .203) are regularly furnishedwith four bearings. 8" five knucklehinges supplied with six bearings.These hinges are intended for use onheavy doors and high frequency doorsfor all types of construction.
Note: One bearing carries the vertical load ontwo bearing hinges. On four bearing hinges,two bearings carry the load.
Door weight, height, width,thickness and frequency of operationare all factors in determining theproper hinge. Four bearing hingesshould be specified whenever there is any question.
McKINNEY steel or stainless steelbased Bearing Hinges are approved foruse on Labeled Applications basedupon Table 1 Reference NFPA-80Table 2-8.1.1 1995 Builders hardware.See catalog page 17 for additionalinformation.
Plain Bearing
Ball Bearing (TB)Oil Impregnated Bearing (TA)
Number of Bearings (Five Knuckle Only)
McKINNEY Hinge CatalogKnuckle Features
5An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
This model offers the most security in a standard hinge. The bearing hingeshave a concealed stainless steel oil-impregnated bearing. Also, an anti-friction bushing in the door leafprovides additional protection againstvertical and lateral wear.
• Plain bearing hinges have an anti-friction component insertedbetween the two knuckles
• The Moderne two knuckle hinge isavailable in stainless steel
• Standard and heavy weight • Pins in all bearing hinges are
stainless steel• Pins in plain bearing hinges are steel
Stainless steel pins are available.• Standard hinges are packed with all
machine by half wood screws• By design, pins are non-rising,
non-removable and tamper protectedby a flush, non-removable cap at theend of the barrel. A door can not beremoved when in the closed position,thus affording maximum security.Intermediate hinges can be orderedopposite hand and installed upsidedown, to inhibit removal of the door inan open position
• Available non-removable door (NRD)hinges have a dowel in the barrel. OneNRD hinge can be ordered per set
• Two knuckle hinges are handed• Template hinges are made to conform
to U.S. Government standards*
Bearing hinges have concealed verticaland lateral thrust twin anti-frictiontype bearings at both joints.
• Plain bearing hinges have an anti-friction T bushing at both joints
• Pin stems in all non-ferrous bearinghinges are stainless steel
• Pins in all ferrous hinges are steel• Pins in all hinges are non-rising type • Standard hinges are packed with all
machine by half wood screws• Hinges are reversible for right or left
hand except anchor hinges and certainelectric hinges
• Template hinges are made to conformto U.S. Government standards*
Bearing hinges are furnished witheither an oil-impregnated bearing(TA*) or ball bearing (TB). (TA isstandard unless TB is specified.)Concealed bearings (TCA) areavailable.
• Pin stems in all non-ferrous bearinghinges are stainless steel
• Pins in all ferrous hinges are steel• Pins in all hinges are non-rising type• Pin caps are made of the same material
as the hinge • Template hinges are made to conform
to U.S. Government standards** Refer to our website atwww.mckinneyhinge.com for additionalinformation regarding McKinney bearings.
Three Knuckle Five KnuckleModerne Two Knuckle
A stud attached to the face of one leafrotates into a cavity in the opposite leafwhen the door is closed. This optioninterlocks the two leaves together,preventing the removal of the dooreven if the pin is removed.
SSF - Safety Stud Feature
*Template hinges are made in sizes, gauges,and with screw holes located to conform toANSI/BHMA A156.7 and U.S.Government standards CS9-65 and SDI.Templates are available on request.
NOTE: Dimensions and weights indicated throughoutthis catalog are in US/SI units; metricequivalents in millimeters and kilograms areshown in parenthesis.
A 7/16" diameter stud projects from theback of each leaf which slips into ahole in the hinge reinforcing plates inboth the door and the frame. Thisprevents the hinge from being removedeven if the screws have been shearedoff. This option is available on theHTA786 steel and HTA386 stainlessprison hinge only.
PSF - Prison Safety Feature
McKINNEY Hinge CatalogTips
6 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
04
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Hospital tips which feature a one-piecenon-removable pin with tapered tips.To order this option prefix our hingenumber by “H”. The hospital tipfeature by design makes the pinvirtually non-removable.
Hospital Tips
Button Tips and plugs are standard onMcKINNEY five knuckle hinges andcan be furnished on three knucklehinges as an option. These tips can bespecified on three knuckle hinges byadding the suffix “E.T.” (exposed tip).
Flush pins and plugs are furnished onour two and three knuckle hinges.
Ball Tips, made of solid brass, areavailable on three and five knucklehinges for a more decorative hingeappearance. To order this option addthe suffix “BT” to the hinge number.
Ball Tips
Standard Tips
Steeple Tips, made of solid brass, areavailable on three and five knucklehinges for a more decorative hingeappearance. To order this hinge option,add the suffix “ST” to the hingenumber.
Steeple Tips
McKINNEY Hinge CatalogPins
7An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Non-Removable Pins
A set screw is driven into the barrel ofthe hinge that is inaccessible when thedoor is in the closed position. To order,add the suffix “NRP” to the hingenumber.
NRP
Two knuckle hinges are available witha non-removable pin which features adowel which is force fitted into thejamb leaf. When the door is hung, thepin is completely concealed andimpossible to remove. One doweledhinge is usually furnished per set ofthree. To order, add the suffix “NRD”to the hinge number.
NRD
Plain Bearing pins are furnished in steeland can be ordered with stainless steelpins as an option. To order this option,add the suffix “SSP” to the hingenumber. Pins on bearing hinges arefurnished in stainless steel.
Two Knuckle
Pin stems in all non-ferrous bearinghinges are stainless steel. Pins in allferrous hinges are steel.
Three Knuckle
Pins on all non-ferrous bearing hingesare stainless steel with the button tipsmanufactured of the same material asthe hinge leaves.
Pins on all ferrous hinges are steel.These hinges are available withoptional brass pins or stainless steelpins. To order these options, add thesuffix “BR” (brass) or “SSP” (stainless).
Five Knuckle
Pins, by design, are non-rising, non-removable and tamper protected by a flush,non-removable cap at the end of the barrel.
McKINNEY Hinge CatalogHinge SelectionCommon Flush Door/Wall/Frame Application
8 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
This section will seek to addressdifferent variations of door, frame and wall conditions which you mightencounter in hanging the door and the product solutions offered byMcKINNEY.
Included are some of the morecommon conditions and some of thenot-so-common conditions. The focushere will be on the type of hinge to usewithin a given door/frame/wallcondition. The following examples are
not intended to cover every possiblesituation in which a particular typehinge might be used, but only arepresentative sampling. Consult thefactory for any unusual installationrequirements not shown here.
The most common application is aflush door/frame/wall condition using ahollow metal frame with a standardhollow metal or wood door which isflush or 1⁄16" inset from the face of theframe, with a wall which is either flush(or inset from the face of the frame.Recommended to hang door for 180˚swing: Full Mortise Hinge. The samehinge could be used with a wood oraluminum frame provided thedoor/frame/wall conditions are flush.
Note: A fire labeled wood door requiressufficient hinge reinforcement to use this type hinge.
Full Mortise Hinge
Furnished as 1⁄4" radius unless specifiedotherwise. 5⁄32" may be specified on fullmortise hinges 41⁄2" or larger. Specifyoption “RC”.
Round Corner Option
MCK TA2714
MCK RCT2714
APPLICATION
McKINNEY Hinge CatalogHinge SelectionUncommon Flush Door/Wall/Frame Applications
9An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
A hollow metal or wood door withchannel iron frame. Recommended tohang door for 180˚ swing: Half Mortise Hinge.
Half Mortise Hinge
MCK TA2771APPLICATION
MCK TA2772APPLICATION
MCK TA2774APPLICATION
A fire labeled wood door (withoutsufficient hinge reinforcement) or akalamein (metal-clad wood door) withchannel iron frame. Recommended tohang door for 180˚ swing: Full Surface Hinge. On fire labeledwood doors, the door leaf is hung usinga back plate with grommet nuts andbolts. Another popular application forthis type hinge is a tubular steel gatehung on a channel iron frame.
A fire labeled wood door (withoutsufficient hinge reinforcement) or akalamein (metal-clad wood door) withhollow metal frame. Recommended tohang door for 180˚ swing: Half SurfaceHinge. On fire labeled wood doors, thedoor leaf is hung using a back platewith grommet nuts and bolts.
Full Surface Hinge
Half Surface Hinge
Less common flush door/frame/wall conditions requiring different typehinges would include:
McKINNEY Hinge CatalogHinge SelectionSpecial Flush Door/Wall/Frame Applications
10 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
On high frequency and/or heavy woodor metal doors, additional anchoring ofthe hinges into the door and jamb maybe necessary. This is a commonapplication in schools, hospitals or anyother buildings where heavy traffic andunusual strain on the doors, jamb andhinges is experienced. Recommendedto hang door for 180˚ swing: FullMortise Anchor Hinge. Sold in sets ofone full mortise anchor hinge and twoheavy weight full mortise hinges.
Some door/frame/wall and even ceilingconditions make door closersimpractical. An alternative closingdevice is the Spring Hinge. Generally,at least two hinges on a door must bespring hinges to provide adequateclosing force. Note: NFPA requires aminimum of two (2) spring hinges onfire labeled doors. With adjustablespring tension on the hinge, theclosing speed of the door is determinedby the amount of closing force set onthe hinge. Spring hinges may not besuitable for applications requiring aclosing device with non-critical closingand latching speed adjustments. Withrespect to meeting ADA requirementsfor closing devices, carpeting and/orgasketing can interfere with latching.McKINNEY offers both Full Mortiseand Half Surface Spring Hinges.
McKinney now offers a ReverseAction,1502R, ( by special request)which allows the door to remain in theopen position. In addition, for highsecurity applications, we offer the TRSoption. This Tamper Resistant Screw isscrewed into the tension ratchet afterthe proper tension has been set.
Spring Hinge MCK 1572 (HALF SURFACE TYPE)MCK 1502 (FULL MORTISE TYPE)
Variations of the basic hinge types may be needed to accommodatespecial situations in flush door/frame/wall conditions:Note: General aforementioned guidelines regarding selection of basic hinge types with respect to door and frame types including fire labeled and applicable to any variations of those hinge types listed hereafter. Variations may not be listed or available in all basic hinge types. Consult the factory for availability.
Anchor Hinge MCK TA792APPLICATION
Note: Anchor hinges are handed and sold foreither square edge doors on hinge side orbeveled (1⁄8" in 2") edge doors on hinge side.Hand and bevel (McKINNEY uses a “5” infront of the item number to indicate 1⁄8" in 2"bevel. Example: TA5792) should be specified.
McKINNEY Hinge CatalogHinge SelectionSpecial Flush Door/Wall/Frame Applications
11An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
04
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
A condition which is common inbarrier free openings, and especially inhospitals, is how to remove the dooredge from the opening at 90˚ of swingwith flush door/wall/ frame conditions.Recommended to hang door withswing to 180˚: Full Mortise SwingClear Hinge. The solution offered bythis hinge is the offset of the hingebarrel to a location along the face ofthe hinge jamb, thereby removing thedoor edge and the barrel of the hinge asobstacles in the opening at 90˚ or moreof swing. If the door is beveled on thehinge side, specify the appropriatebeveled hinge and handing for yourapplication*.
* Consult individual Swing Clear catalog pagesfor beveled hinge product numbers.
Swing Clear Hinge MCK TA2895APPLICATION
Meets or exceedsANSI A117.1 - 1986Providing Accessibilityand Usability forPhysicallyHandicapped People
McKINNEY Hinge CatalogHinge SelectionNon-Flush Door/Wall/Frame Applications
12 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Not all door/frame/wall conditions are flush and, in order to hang thedoor, other variations on the basic hinge types may be needed.
If the door is not flush with the frame,is sitting back in a deep reveal from theface of the frame with or withoutadditional obstacles created by appliedtrim on the face of the frame or adeeper reveal caused by a projectingwall, and the door is to swing 180˚, thena Full Mortise Wide Throw Hingemay be used in hanging the door.
Important in this regard is how tocalculate the proper width of a widethrow hinge (rounded to the nexthigher whole number if result is not awhole number: e.g., 6", 7", 8", etc.)
Wide Throw Hinge
1. If the door is sitting inside a deepframe reveal with no otherobstacles (i.e., projecting trim orwall), add the depth of the reveal(distance from the face of theframe to the face of the door) tothe recommended width of hingeused under flush conditions. Example: A 6" wide (wide throw)hinge would replace a 41⁄2" wideregular mortise hinge (used underflush conditions) if the depth ofthe reveal is 11⁄2".
2. If the door is to clear projectingtrim or wall and the barrel of thehinge is not obstructed, thencalculate as follows:
(a) double the size of the door
(b) subtract 1⁄2" if the door thickness is less than or equal to21⁄4" or subtract 3⁄4" if the doorthickness is greater than 21⁄4"
(c) add for the additional depthfrom the face of the obstruction tothe face of the door
(d) add for clearance between thedoor and the face of theobstruction at 180˚ of swing(generally 1" or more).
If, for instance, you have a 13⁄4"thick door:
(a) 13⁄4" door thickness x 2 = 31⁄2"
(b)less 1⁄2" equals 3"
(c) plus 3" for the additional depthfrom the face of the wall to theface of the door equals 6"
(d) plus 1" for the clearancebetween the door and the face ofthe obstruction at 180˚ of swingequals 7" overall hinge width.
MCK TA2798APPLICATION
How to Calculate
McKINNEY Hinge CatalogHinge Selection
13An ASSA ABLOY Group company An ASSA ABLOY Group company May
2005
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
An increasingly popular door, frameand wall condition in corridors iscross-corridor or double egress pairs ofdoors standing in wall pockets at 90˚ ofswing, so as to be clear of the initialopening and out of the corridoraltogether. Solution: Pocket Hinge.
As corridor doors are often firelabeled, the hardware must beapproved for use in fire labeledopenings. Solution: the McKINNEYPH-4 Pocket Hinge. U.L. approvedfor use on both hollow metal and steelcovered composite fire doors rated upto 3 hours and on wood core type firedoors rated 20 minutes.
Pocket Hinge
Recommended for use on averagefrequency double acting doors inschools, hospitals, institutions andother public buildings. Not for use onlabeled doors and frames.
Pivots
If the door is not flush with the framebut rather is sitting back in a deepreveal from the face of the frame a FullMortise Raised Barrel Hinge may beused in hanging the door. The solutionoffered by this hinge is the offset of thehinge barrel away from the hinge jamb.Bevel of door edge should be specified.
Raised Barrel Hinge
MCK PH-4APPLICATION
EP-5J
RAISED BARREL SQUARE EDGE DOOR RAISED BARREL BEVELED EDGE DOOR
McKINNEY Hinge CatalogHinge Selection
14 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
McKINNEY Aluminum ContinuousHinges consist of two anodized, full-height, bearing-geared leaves that areheld together by a full-length channelcap. This design provides properalignment and eliminates prematurewear. The geared construction andfull-length channel cap seals the gapbetween the door and frame andprovides privacy and security againstprying. This feature also provides safetyagainst pinched fingers especially inpublic areas where children are apt tomove throughout the opening. Thegear design ensures identical operationof each leaf, and even-distribution ofload stress along the full length of the
door and frame which eliminates doorsag and binding. Mortising is notnecessary, and the hinge doubles asweather stripping on the hinge side.These hinges are tested and certifiedby UL® (USA & CANADA) tostandards UL 10C and UBC7.2(positive pressure) for up to a 3-hour(A-Label) Fire Listing for all4'0"x10'0" and 8'0"x10'0" door andframe assemblies. Fire testingcertification applies to all approvedhollow metal and wood doorassemblies in dry wall or masonry wallconstruction. FirePins™ are now onlyrequired on 3-Hour (A-label)Assemblies. These hinges have been
cycle tested using a 150 lb. Door andare now certified fully functional after1.5 million cycles. The screw holelocations on these hinges are ideallysuited for use on lead lined doors (i.e.hospital X-ray rooms. Refer to theAluminum Continuous Hinge pagesection for additional information.
McKINNEY Steel or Stainless ContinuousHinges are fabricated from independentlymachined 14 gauge cold rolled steeland finished in prime coat, or 304stainless steel door leaves. The concealedTeflon-coated stainless steel pin andtwin self-lubricated nylon bearings ateach knuckle provides for properalignment and smooth operation.
These hinges are UL® (USA &CANADA) up to a 3-hour (A-label)Fire Listing for 4'0"x8'0" single doorsand 8'0"x8'0" pairs of doors. The non-handed, slim barrel design isrecommended for new constructionand retrofit installations. Refer to theSteel and Stainless Continuous Hingepage section for additional information.
Aluminum Continuous Hinges – GUARANTEED FOR THE LIFE OF THE OPENING
Steel and Stainless Steel Continuous Hinges – GUARANTEED FOR THE LIFE OF THE OPENING
FULL SURFACE CENTER PIVOT 58 SERIES
FULL MORTISE 12, 14, 25 SERIES HALF-SURFACE 54 SERIES FULL SURFACE 22 SERIES
FULL SURFACE MCK-FS302
FULL MORTISE MCK-FM300, MCK-HG305, MCK-HG315 HALF MORTISE MCK-HM304, MCK-HG306 SWING CLEAR MCK-HG311
may be used as swing clear
Note: Not all products shown. Refer to pages 113 - 122 for additional information.
McKINNEY Hinge CatalogReference Charts
15An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Hollow Metal Door Weights by Gauge Wood Door Weights by Door ThicknessDoor Gauge – # Per Square Foot # Per Square Foot
20 Gauge Door 4 Door Thickness 1-3/8" 1-3/4"
18 Gauge Door 5 Particle/Mineral Core 4.75 5.25
16 Gauge Door 6 Stave Core Wood 3.75 4.25
14 Gauge Door 7 Hollow Core Wood 1.3 1.5
Door, Frame Wall Conditions Frame Type Door Type Hinge Type
Variation of Basic Hinge Type
Shown Below (See Note 2)
McKINNEY Example
(See Note 3)
Flush* Wood or Metal Wood or Metal Full Mortise (not applicable) TA2714
Flush* Channel Iron Wood or Metal Half Mortise (not applicable) TA2774
Flush* Channel Iron Kalamein or Fire Labeled Wood Door (see Note 1)
Full Surface (not applicable) TA2771
Flush* Metal Kalamein or Fire Labeled Wood Door (see Note 1)
Half Surface (not applicable) TA2772
Flush* MetalHeavy and/or High Frequency
Wood or MetalAnchor Full Mortise TA792
Flush* Wood or Metal Wood or Metal Requiring Alternative Closing Device
Spring Full Mortise Half Surface
1502, 1572
Flush* Wood or Metal Wood or Metal Required to Clear Opening at 90˚ of Swing
Swing Clear Full Mortise TA2895
Deep Frame Reveal Wood or Metal Wood or Metal with Maximum Swing of 90˚ to 110˚
Raised Barrel Full Mortise RBTA2714
Deep Frame Reveal with or without Trim on the Face of the Frame or a Projecting Wall
Wood or MetalWood or Metal with swing to 180˚ Wide Throw Full Mortise TA2798
Wall Pocket at 90˚ of swing
Metal Wood or Metal Pocket Hinge (not applicable) PH-4
The following wood and metal doorweights are provided as a convenienceto catalog users. They are approximateand will vary slightly among doormanufacturers. The weight of the doorhardware should be added to theweights listed below. For any thicknessnot shown, the individualmanufacturer’s catalog should beconsulted.
Door Weights (Based upon 3'0"x7'0" Door Size(Weights do not include hardware)
Quick Reference Chart
* Includes door and frame conditions of up to 1⁄8" inset
Notes:
(1) Fire labeled wood door without sufficient hinge reinforcement. Door leaf is hung using back plate with grommet nuts and bolts.
(2) The four basic hinge types are full mortise, half mortise, full surface and half surface. Variations (i.e. anchor, swing clear, raised barrel, wide throw) are available in the basic types shown above but may not be available in all basic hinge types. Consult individual catalog pages for availability.
(3) Consult individual catalog pages for available sizes, weights, materials, versions, bearings and finishes. Hinges for doors beveled (1⁄8" in 2") on hinge side use 5000 series for 3K hinges (e.g. TA5792); use 4000 series for 5K hinges (e.g., TA4895).
Door Weights
McKINNEY Hinge CatalogReference Charts
16 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Knowing the door thickness and trimprojection, use the following formulafor determining minimum hinge widthof all full mortise hinges:
(1) Door thickness(2) Backset(3) Required Clearance(4) Inset
Door thickness minus the backsetmultiplied by 2, plus the requiredclearance, plus the inset (if applicable)will equal the proper hinge width.
D = Door Thickness T = Trim Depth W = Hinge Width
Clearance
"T"
"W"
"D"
For doors up to 21/2" thick: W=(2 x D) + T For doors 21/2" to 3" thick: W=(2 x D)+(2 x T)+ 1/4"
Door Heightin Inches (MM)
# of HingesPer Door
Up to 60 (1524) 2
60 to 90 (1524 to 2286) 3
90 to 120 (2286 to 3048) 4
Recommended Number of Hingesper Door 3'0" Wide (Wood or Metal)
Expected Frequency of Door OperationHow to Determine the Proper Hinge Width
One Cycle = one complete opening and closing
Expected FrequencyInstallation Type Daily Yearly
COMMERCIAL
Commercial Store Entrance 5,000 1,5000,000Office Building Entrance 4,000 1,200,000Theatre Entrance 1,000 450,000School Entrance 1,250 225,000School Restroom Door 1,250 225,000Store or Bank Entrance 500 150,000Office Building Restroom Door 400 118,000School Corridor Door 80 15,000Office Building Corridor Door 75 22,000Store Restroom Door 60 18,000
RESIDENTIAL
Entrance 40 15,000Restroom Door 25 9,000Corridor Door 10 3,600Closet Door 6 2,200
Note: We recommend that bearing hinges be used on allabove categories other than “Residential”.
Low
Ave
rage
Hig
h
Door Hinge Max ClearanceThickness Width Provided
13⁄8" 31⁄2" 11⁄4"4" 13⁄4"
13⁄4" 4" 1"41⁄2" 11⁄2"
5" 2"
6" 3"
2" 41⁄2" 1"5" 11⁄2"6" 21⁄2"
21⁄4" 5" 1"6" 2"
Trim Clearance
The table above indicates the trimclearance provided by hinges of specifiedwidths on flush doors, not inset, ofstandard thickness. For doors of otherthicknesses, apply the proper formula.
The hinge widths of half mortise, halfsurface and full surface hinges arestandard, depending on the hinge length.Note that in these hinge types, theamount of clearance available isdetermined by the amount of offset andnot by the hinge width.
Recommended Size of Hinges per Door (Wood or Metal)
13⁄8 (35)
13⁄8 (35)
13⁄4 (44)
13⁄4 (44)
13⁄4 (44)
2 - 21⁄2 (51 - 64)
2 - 21⁄2 (51 - 64)
31⁄2 (89)
4 (102)
41⁄2 (114)
5 (127)
6 (152)
5 (127) HW
6 (152) HW
*
*
*
* Heavy weight hinges should be used on allextra heavy doors or those exposed to highfrequency use. Consult the factory for doorswider than 3'0". Five knuckle heavy weighthinges are four bearing. The following gauges of metal may apply:
Heavy weight 4-1⁄2" (114) high = .180 gaugeHeavy weight 5" (127) high = .190 gaugeHeavy weight 6" (152) high = .203 gauge
Note: Five knuckle 8" (203) high hinges have six bearings.
Note: On hinge size the dimension shown is the hingeheight. Where full mortise or other hinges withtwo dimensions are used, the first dimensiongiven is always the height. The seconddimension is the hinge width when open.
Up to 36 (914) .123
Over 36 (914) .130
Up to 36 (914) .134
Over 36 - 48 (914 - 1219)
.134
Over 48 (1219) .160
Up to 42 (1067) .190
Over 42 (1067) .203
Door Thickness in Inches (MM)
Door Width in Inches (MM)
Hinge Height in Inches (MM)
Hinge Gauge
McKINNEY Hinge CatalogReference Charts
17An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
The top of the top hinge should be 5" from thejamb header.The bottom of the bottom hinge should be 10"from the finished floor.The center of the center hinge should beequidistant from the other two.EXCEPTION: The McKINNEY Anchor Hinge mounts at thevery top of the door.On doors over 7’6" high, fourhinges are required.
For 13⁄4" (44.5mm) or Thicker Doors3 11⁄2 1 3⁄4 1⁄2 1⁄3 4 (1.22) 10 (3.05) 41⁄2 (114.3) 0.180 (4.57) Steel, Mortise or Surface3 11⁄2 1 3⁄4 1⁄2 1⁄3 4 (1.22) 8 (2.44) 41⁄2 (114.3) 0.134 (3.40) Steel, Mortise or Surface
11⁄2 3⁄4 1⁄2 1⁄3 3’2" (0.96) 8 (2.44) 6 (152.4) 0.225 (5.72) Steel-Olive Knuckle or Paumelle3 11⁄2 3⁄4 1⁄2 1⁄3 4 (1.22) 10 (3.05) 4 (101.6) 0.225 (5.72) Steel Pivots (including top, bottom and intermediate)
11⁄2 1 3⁄4 1⁄2 1⁄3 3 (0.91) 5 (1.52) 4 (101.6) 0.130 (3.30) Steel Mortise or Surface11⁄2 1 3⁄4 1⁄2 1⁄3 2 (0.61) 3 (0.91) 3 (76.2) 0.092 (2.34) Steel, Mortise or Surface
3 11⁄2 1 3⁄4 1⁄2 1⁄3 3 (0.91) 7 (2.13) 41⁄2 (114.3) 0.134 (3.40) Steel, Mortise or Surface (labeled self closing spring type)3 11⁄2 1 3⁄4 1⁄2 1⁄3 3 (0.91) 7 (2.13) 4 (101.6) 0.105 (2.67) Steel, Mortise or Surface (labeled self closing spring type)
For 13⁄8" (34.93mm) Doors3 11⁄2 3⁄4 1⁄2 1⁄3 3 (0.91) 7 (2.13) 31⁄2 (88.9) 0.123 (3.12) Steel, Mortise or Surface3 11⁄2 1 3⁄4 1⁄2 1⁄3 2’8" (0.81) 7 (2.13) 31⁄2 (88.9) 0.105 (2.67) Steel, Mortise (spring closing)
Notes:
(1) All hinges or pivots, except spring hinges, shall beof the ball-bearing type. Hinges or pivotsemploying other antifriction bearing surfaces arepermitted if they meet the test requirements ofANSI A156.1, Standard for Butts and Hinges. Springhinges shall be labeled.
(2) 41⁄2" (114mm) high, 0.180" (4.57mm) thick hingesshall be permitted for use on wide and heavy doorsor doors that are subjected to heavy use or unusualstress.
(3) Some manufacturers can provide fire doors withhinges of lighter weight that are not of the ballbearing type where they are part of a listedassembly and meet the test requirements of ANSI
A156.1, Standard for Butts and Hinges, and havebeen tested to a minimum of 350,000 cycles.
(4) Pivot sets made up of components that are smallerand/or of a lighter gauge than shown in Table 2-8.1.1 shall be permitted to be used, provided theymeet the requirements of ANSI A156.4, DoorControls (Closers) and are in accordance with themanufacturers’ labeled service procedures.
Maximum Door Size Minimum Hinge SizeDoor Rating, Hr. Width ft. (m) Height ft. (m) Height in. (mm) Thickness in. (mm) Type Hinge
Table 1 Reference NFPA-80 Table 2-8.1.1 1995 Builders Hardware
The requirements of the Underwriters’Laboratories, Inc., for fire doorhardware are determined by door label,which in turn is established by thelocation of the opening. The followingare the classifications of Underwriter’sLaboratories, Inc.
On all public and some private heavyconstruction three hinges are requiredfor each door. This practice is standardunder U.S. Government specificationsand is required under most buildingcodes and Fire Underwriters’specifications.
Three hinges assure proper dooralignment and enable other hardware
to function properly. There is less doorwarping and less hinge wear. On lightwood doors the alignment problem isas great as on heavy doors so less thanthree hinges should never beconsidered.
DoorSituation
Location
Class A Fire Walls
Class B Vertical Shafts
Class C Corridor & Room Partitions
Class DExterior Walls(severe fire exposure)
Class DExterior Fire Escapes(severe fire exposure)
Class EExterior Wallsmoderate fire exposure)
Class EExterior Fire Escapes(moderate fire exposure)
Underwriters’ LaboratoriesRequirements
5"
EQUAL
EQUAL
10"
Mortise and Surface Hinges, Pivots or Spring Hinges for Swinging Doors. Doors up to 60“ (1.52 m) in height shall be provided with two hinges and an additional hinge for each additional 30" (0.76 m) of doorheight or fraction thereof. The distance between hinges shall be permitted to exceed 30" (0.76 m). Where spring hinges are used, at least two shall be provided.
Reprinted with permission from NEPA 80, Fire Doors and Fire Windows, Copyright ©1995, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association on the referenced subject which is represented only by the standard in its entirety.
McKINNEY Hinge CatalogHand of Doors and Hinges
18 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
All doors are handed - right or left. The following illustrations indicate clearly this“handing” as it is understood within the hardware industry.
(Hand of door is determined from the outside)When standing on outside of door and hinges are on the right, it is right hand.When hinges are on the left, it is left hand.
A double acting door opens from you and toward you, therefore it is not calledreverse like a single acting door.
Hand of Doors
McKINNEY Anchor Hinges arehanded right or left as are McKINNEYModerne, Olive, Knuckle, Paumelle,Beveled Edge and CS Electric typehinges. Full surface, half surface andhalf mortise hinges with set screw(NRP) in the barrel are manufacturedas reversibles (with no hole in plug).
A simple method of determiningthe hand of all loose joint hinges is toopen the hinge full with thecountersunk screw holes in view. If thehinge can be held by the right handleaf and it does not fall apart, it is aright hand (RH) hinge. If the hingemust be held by the left hand leaf tokeep it from falling apart, it is a lefthand (LH) hinge.
The hand of hinges may bespecified by suffixing the symbols RHor LH to the catalog number.
Hand of Hinges
REGULAR DOORS OPENING IN
OUTSIDELeft Hand Door takes left hand hinges
OUTSIDERight Hand Door takes right hand hinges
REVERSE DOORS OPENING OUT
OUTSIDELeft Hand Reverse Door takes right hand hinges
OUTSIDERight Hand Reverse Door takes left hand hinges
DOUBLE ACTING
Left Side of HingeLeft Hand Door
Right Side of HingeRight Hand Door
Right Side of Hinge Left Side of Hinge
Outside
McKINNEY Hinge CatalogHinge Swaging
19An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
All hinges for full mortise applicationsare swaged. Normal swaging onstandard and heavy gauge hingesprovides a clearance of 1⁄16" when theleaves are parallel. Full mortise widethrow hinges have a clearance of 3⁄32".
Swaging is the slight offset in the hinge leaves which permits them toclose to a parallel position as the door closes.
Full Mortise
Hinges for full surface applications arenot swaged. Blank hinges are for fullsurface welded application and arealways furnished “flat back” unlessspecified otherwise when ordered.
Full Surface
Hinges for beveled door applicationshave one leaf swaged at an angle of31⁄2˚ (1⁄8" in 2") to maintain properdoor and frame clearance when doorsare beveled on the hinge side. Specifyhanding on these hinges.
Beveled Door
When only one leaf is swaged, the non-swaged leaf is approximately 1⁄16"shorter as a standard. For all hollowmetal door and frame applications,both leaves must be the same width.On your order, specify “Leaves must be equal”.
One Leaf Swaged
When only one leaf is swaged flat, thenon-swaged leaf is approximately 3⁄32"shorter as a standard. For all hollowmetal door and frame applications,both leaves must be the same width.On your order, specify “Leaves must be equal”.
One Leaf Swaged Flat
Hinge with One Leaf Swaged Hinge with One Leaf Swaged Flat
Hinge Opened
Hinge Closed
Hinge Opened
Hinge Closed
Hinge Opened
Hinge Closed
McKINNEY Hinge CatalogScrews and Fasteners
20 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
McKINNEY hinges are manufacturedwith templated screw hole locationsand tolerances which conform to theAmerican National Standards Institute(ANSI/BHMA A-156.7). McKINNEYpublishes a complete listing oftemplates which list the overall hingesize, material gauge and exact screwhole location. The most currenttemplates are found on our website @www.mckinneyhinge.com. Thesetemplates should be consulted prior toany door or frame preparation.
MACHINE AND WOOD SCREWS
McKINNEY offers a wide variety ofscrews and fasteners.
Shown:1. Torx Bit and Driver2. Spanner Bit and Driver3. Phillips Head Machine Screw4. Torx Head Machine Screw5. Spanner Head Machine Screw6. Torx Head Wood Screw7. Spanner Head Wood Screw8. Phillips Head Wood Screw9. Oval Phillips Head Machine Screw
with Grommet Nut
TORX DRIVER & SPANNER DRIVER
TEMPLATED SCREW HOLES
1
2
93 4 5 6 7 8
McKINNEY Hinge CatalogScrews and Fasteners
21An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
Full Mortise Hinges
31⁄2 x 31⁄2 1⁄2 x 10-24 1 x 1031⁄2 x 5 1⁄2 x 10-24 1 x 10
4 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12
4 x 6 1⁄2 x 12-24 11⁄4 x 124 x 7 1⁄2 x 12-24 11⁄4 x 12
41⁄2 x 6 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 7 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 8 1⁄2 x 12-24 11⁄4 x 12
5 x 4 1⁄2 x 12-24 11⁄4 x 125 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 125 x 7 1⁄2 x 12-24 11⁄4 x 125 x 8 1⁄2 x 12-24 11⁄4 x 126 x 5 1⁄2 x 1⁄4-20 11⁄4 x 146 x 6 1⁄2 x 1⁄4-20 11⁄4 x 148 x 6 1⁄2 x 1⁄4-20 11⁄4 x 148 x 8 1⁄2 x 1⁄4-20 11⁄4 x 14
Size of Hinge Machine WoodScrews Screws
All five knuckle 41⁄2 x 41⁄2 full mortisesteel hinges (except US-P) are packedall machine (8 ea.) x all wood (8 ea.)screws. Two and three knuckle, as wellas all other sizes of five knuckle steel fullmortise and all non-ferrous full mortisehinges are packed with all machine (8 ea.) x 1⁄2 wood (4 ea.) screws.
Packing:
41⁄2 1⁄2 x 12-24
5 1⁄2 x 12-24
6 1⁄2 x 1⁄4-20
MachineSize of Hinge Screws
Swing Clear Hinges
41⁄2 1⁄2 x 12-24 2 x 1⁄4-20
5 1⁄2 x 12-24 2 x 1⁄4-20
Machine ThruSize of Hinge Screws Bolts
Full Surface Hinges
41⁄2 1⁄2 x 12-24 2 x 1⁄4-20
5 1⁄2 x 12-24 2 x 1⁄4-20
6 1⁄2 x 1⁄4-20 2 x 1⁄4-20
Machine Thru Bolts &Size of Hinge Screws Grommet Nut
Half Surface Hinges
41⁄2 1⁄2 x 12-24 2 x 1⁄4-20
5 1⁄2 x 12-24 2 x 1⁄4-20
6 1⁄2 x 1⁄4-20 2 x 1⁄4-20
Machine Thru Bolts &Size of Hinge Screws Grommet Nut
Half Mortise Hinges
McKINNEY Hinge CatalogFinishes
22 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
04
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
U.S. Finish Description McKINNEY
US P Primed for Painting P
US 2C Zinc Plated, Commercial 2C
US 2G Zinc Plated, Governmental 2G
US 3 Bright Brass 3
US 4 Dull Brass 4
US 5 Dull Brass, Oxidized 5
US 7 Brass, Nickel Oxidized, Bright Relieved 7
US 9 Bright Bronze 9
US 10 Dull Bronze 10
US 10A Antiqued Bronze, Oiled and Lacquered 10A
US 10B Antiqued Bronze, Oiled 10B
US 11 Dull Bronze, Oxidized 11
US 14 Bright Nickel Plated 14
US 15 Dull Nickel Plated 15
US 15A Nickel Oxidized Relieved 15A
US 17A Half Polished Iron, Smooth 17A
US 20 Statuary Bronze, Light 20
US 20A Statuary Bronze, Dark 20A
US 26 Bright Chromium 26
US 26D Dull Chromium 26D
US 32 Polished Stainless Steel 32
US 32D Dull Stainless Steel 32D
McKINNEY and Government Finish Symbols
McKINNEY Powder Coat Finishes
Aluminum AP
Beige PB
Gold PG
Grey Tone GT
White PW
Bright Brass with Clear Powder Coat 3-C
Dull Brass with Clear Powder Coat 4-C
Dull Nickel with Clear Powder Coat 15-C
Co-Laq - Dark D-3
Co-Laq - Black D-4
Custom Polymer Coating *
Every effort is made by McKINNEY tofurnish finishes which do comply withthe U.S. Standard. However, wecannot guarantee that our finish willmatch other manufacturers’ finish.Where a special finish or a matchedfinish is required, a sample must besubmitted with the order.
McKINNEY’s electrostatically appliedpolyester powder finishes have beentested to exceed all recommended salt-spray testing requirements. These finisheshave also been proven to be by far thebest finish for steel hinges in areas wherehardware is susceptible to corrosion suchas caused by high humidity, moisture orcoastal environments.
McKINNEY Hinge CatalogFinishes
23An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
B.H.M.A.Code
Finish Description Base MaterialMcKINNEYEquivalent
600 Primed for Painting Steel USP
602 Zinc Plated, Commercial Steel US2C
603 Zinc Plated, Governmental Steel US2G
605 Bright Brass Brass US3
606 Dull Brass Brass US4
609 Dull Brass, Oxidized Brass US5
610Brass, Nickel Oxidized, BrightRelieved
Brass US7
611 Bright Bronze Bronze US9
612 Dull Bronze Bronze US10
613 Antiqued Bronze, Oiled Bronze US10B
616 Dull Bronze, Oxidized Bronze US11
618 Bright Nickel Plated Brass, Bronze US14
619 Dull Nickel Plated Brass, Bronze US15
620 Nickel Oxidized Relieved Brass, Bronze US15A
621 Half Polished Iron, Smooth Brass, Bronze US17A
623 Statuary Bronze, Light Bronze US20
624 Statuary Bronze, Dark Bronze US20A
625 Bright Chromium Brass, Bronze US26
626 Dull Chromium Brass, Bronze US26D
629 Polished Stainless SteelStainless Steel
300 SeriesUS32
630 Dull Stainless SteelStainless Steel
300 SeriesUS32D
632 Bright Brass Steel US3
633 Dull Brass Steel US4
636 Dull Brass, Oxidized Steel US7
637 Bright Bronze Steel US9
639 Dull Bronze Steel US10
640 Antique Bronze, Oiled Steel US10B
643 Dull Bronze, Oxidized Steel US11
645 Bright Nickel Plated Steel US14
646 Dull Nickel Plated Steel US15
647 Nickel Oxidized Relieved Steel US15A
648 Half Polished Iron, Smooth Steel US17A
649 Statuary Bronze, Light Steel US20
650 Statuary Bronze, Dark Steel US20A
651 Bright Chromium Steel US26
652 Dull Chromium Steel US26D
McKINNEY and B.H.M.A. Finish Symbols McKINNEY hinge finishes meet orexceed the American National Standardsfor materials and finishes (ANSI/BHMA- A156.18 and BHMA 1301).
Ferrous BaseSteel base hinges which are
polished and plated are dipped inlacquer, baked and dried. US4 Finishover steel, a purely decorative finishwhich in the past was susceptible topitting is now furnished with a nickelbase for added durability, and followedby 20 minutes of brass and then lacquered.This new process allows McKinney tohave one of the best US4 finish in theindustry. However, brass finishes oversteel should not be cleaned with anytype of paint remover or abrasivemethod which will remove the lacquer.
Our US10B is a true oil rubbedfinish. However, due to excessivehandling on installation of electrichinges and sample cards, we use a 10BLwith a very light lacquer to protect thefinish.
Steel hinges which are supplied inprime coat are finished with Powder CoatPrime finish which is ready for paintingin the field, or durable enough to letstand on its own.
Non-Ferrous Base (should be usedfor exterior installations).
Brass or Bronze hinges are polishedand plated.
Stainless Steel hinges are passivatedto remove any impurities in thestainless material, then polished to asatin finish (US32D) or can bepolished to a bright finish (US32).
McKINNEY Hinge Catalog
24 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
INTENTIONALLYLEFT
BLANK
McKINNEY Hinge CatalogFull Mortise Plain Bearing HingesTwo Knuckle Standard Weight Series
25An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Steel base polished and plated or furnished in prime or powder coat finish.
31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .13441⁄2 x 41⁄2 114.3 x 114.3 .134
Available Sizes
Inches MM Gauge All 2K standard weight full mortiseplain bearing steel hinges are packed allmachine x 1⁄2 wood screws. For specialscrews consult price book on avail-ability. Specify hand when ordering.
Not recommended for medium or high frequency doors, or doors withclosing devices.
T2731
• NRD (non-removable door - one doweled hinge furnished per set)
• RC (round corner - 1⁄4" radius furnished unless specified otherwise)
• HT (hospital tip)• SSF (safety stud feature)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are on hinge side specify T4731)
APPLICATION
Available Options:
A8133 Steel
ANSI Cross Reference:
Packing:
McKINNEY Hinge CatalogFull Mortise Bearing HingesTwo Knuckle Standard Weight Series
26 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
• NRD (non-removable door - one doweled hinge furnished per set)
• RC (round corner - 1⁄4" radius furnished unless specified otherwise)
• HT (hospital tip)• SSF (safety stud feature)• CC-4 (concealed circuit - 4 wire)• CC-6 (concealed circuit - 6 wire)*• CC-8 (concealed circuit - 8 wire)*• CS- (concealed switch)*• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify TA4331 or TA4731)
* Not available in Stainless
All 2K standard weight full mortisebearing hinges are packed all machinex 1⁄2 wood screws. For special screwsconsult price book on availability.Specify hand when ordering.
Stainless steel base or available in brass or bronze base material polishedand plated or furnished in prime orpowder coat.
Steel base polished and plated or furnished in prime or powder coat finish.
31⁄2 x 31⁄2* 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .134
41⁄2 x 41⁄2 114.3 x 114.3 .134
5 x 41⁄2 127 x 114.3 .146
5 x 5 127 x 127 .146
* Not available in Stainless
TA3331 TA2731
Available Sizes
Inches MM Gauge
APPLICATION
Available Options:
A2112 Brass, BronzeA5112 StainlessA8112 Steel
ANSI Cross Reference:
Recommended for standard weight, medium frequency doors, or doors with closing devices.
Packing:
McKINNEY Hinge CatalogFull Mortise Bearing HingesTwo Knuckle Heavy Weight Series
27An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
• NRD (non-removable door - one doweled hinge furnished per set)
• RC (round corner - 1⁄4" radius furnished unless specified otherwise)
• HT (hospital tip)• SSF (safety stud feature)• CC-4 (concealed circuit - 4 wire)• CC-6 (concealed circuit - 6 wire)*• CC-8 (concealed circuit - 8 wire)*• CS- (concealed switch)*• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify TA5350 or TA5750)
* Not available in Stainless
All 2K heavy weight full mortisebearing hinges are packed all machinex 1⁄2 wood screws. For special screws consult price bookon availability. Specify hand whenordering.
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.
Stainless steel base or available in brass or bronze base material polishedand plated or furnished in prime orpowder coat.
Steel base polished and plated or furnished in prime or powder coat finish.
41⁄2 x 41⁄2 114.3 x 114.3 .1805 x 41⁄2 127 x 114.3 .190
5 x 5 127 x 127 .190
* Not available in Stainless
TA3350 TA3750
Available Sizes
Inches MM Gauge
Available Options:
A2111 Brass, BronzeA5111 StainlessA8111 Steel
ANSI Cross Reference:
Packing:APPLICATION
McKINNEY Hinge CatalogFull Mortise Plain Bearing HingesThree Knuckle Standard Weight Series
28 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Steel base polished and plated or furnished in prime or powder coat finish.
All 3K standard weight full mortiseplain bearing hinges are packed all machine x 1⁄2 wood screws. For special screws consult price bookon availability.
Not recommended for medium or high frequency doors, or doors with closing devices.
31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .134
41⁄2 x 41⁄2 114.3 x 114.3 .134
5 x 41⁄2 127 x 114.3 .146
5 x 5 127 x 127 .146
Available Sizes
Inches MM Gauge
T714
• NRP (non-removable pin)• ETC (exposed tip)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• SSF (safety stud feature)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify T5714)
Available Options:
A8133 Steel
ANSI Cross Reference:
Packing:APPLICATION
McKINNEY Hinge CatalogFull Mortise Bearing HingesThree Knuckle Standard Weight Series
29An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All standard weight full mortise non-ferrous hinges are packed with allmachine x 1⁄2 wood screws. For specialscrews consult price book on availability.
Packing:
• NRP (non-removable pin)• ETC (exposed pin and plug)• RC (round corner - 1⁄4"radius furnished
unless specified otherwise)• HT (hospital tip)• SSF (safety stud feature)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available• CC (concealed circuit) 4, 6 or 8 wire
available*• CS-(concealed switch - handing required)*• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify TA5314 or TA5714)
* Not available in Stainless
Recommended for standard weight, medium frequency doors, or doors with closing devices.
Brass or bronze base polished and plated, or stainless steel base polished and passivated.
Steel base polished and plated or furnished in prime or powder coat finish.
31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .13441⁄2 x 41⁄2 114.3 x 114.3 .134
5 x 41⁄2 127 x 114.3 .1465 x 5 127 x 127 .146
Available Sizes
Inches MM Gauge
TA314 TA714 Available Options:
A2112 Brass, BronzeA5112 StainlessA8112 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogFull Mortise Bearing HingesThree Knuckle Heavy Weight Series
30 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortise hingesare packed all machine and 1⁄2 woodscrews. For special screws consult pricebook on availability.
Packing:
• NRP (non-removable pin)• ETC (exposed pin and plug)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• SSF (safety stud feature)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available• CC (concealed circuit) 4, 6 or 8 wire
available*• CS- (concealed switch - handing required)*• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyTA5386 or TA5786)
• 8x6 furnished in steel only (hole pattern differs from photo shown)
* Not available in Stainless
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.
Stainless steel base or available in brass or bronze base material polishedand plated or furnished in prime orpowder coat.
41⁄2 x 41⁄2 114.3 x 114.3 .1805 x 41⁄2 127 x 114.3 .1905 x 5 127 x 127 .1906 x 5 152.4 x 127 .2036 x 6 152.4 x 152.4 .203
8 x 6* 203.2 x 152.4 .225
Steel base material polished and platedor furnished in prime or powder coat.
Available Sizes
Inches MM Gauge
TA386 TA786 Available Options:
A2111 Brass, BronzeA5111 StainlessA8111 Steel
ANSI Cross Reference:
* Consult templates 046A and 046B forappropriate hole pattern.
APPLICATION
McKINNEY Hinge CatalogFull Mortise Institutional HingesThree Knuckle Heavy Weight Series
31An ASSA ABLOY Group company An ASSA ABLOY Group company Feb
ruar
y 20
06
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortiseinstitutional hinges are packed with allTorx Head Security machine screws.For special screws consult price bookon availability.
Packing:
• PSF (prison safety feature)(shown below)• CC-4 (concealed circuit - 4 wire)• MM (magnetic monitoring)*• Beveled Edge (where doors are
beveled on hinge side specify IHTB5386 or IHTB5786)
* Not available with PSF option
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where security requirements exist.
Stainless steel base material polishedand passivated or sand blasted andfurnished in prime coat. Hospitaltipped ends, double stainless steeldowel construction, concealed bearing assemblies.
41⁄2 x 41⁄2 114.3 x 114.3 .180
5 x 41⁄2* 127 x 114.3 .190
Steel base material polished and platedor furnished in prime or powder coat.Hospital tipped ends, double stainlesssteel dowel construction, concealedbearing assemblies.
Available Sizes
Inches MM Gauge
IHTB386 IHTB786
PRISON SAFETY FEATURE (PSF)(OPTIONAL)
HOSPITAL TIP (HT)
Available Options:
A5111 StainlessA8111 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogSwing Clear Full Mortise Bearing HingesThree Knuckle Heavy Weight Series (Reversible)
32 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortise hingesare packed with all machine and 1⁄2wood screws. For special screws consultprice book on availability. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.
Packing:
• RC (round corner - 1⁄4" radius furnished unless specified otherwise)
• HT (hospital tip)• SSF (safety stud feature)• MM (magnetic monitoring)• Beveled Edge (where doors are beveled
on hinge side specify TA5795)
Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. Hinge allows for maximum clearance for passage of beds, tables or other equipment throughdoorway. Pressed steel jambs require no special reinforcing.
Steel base material polished and plated or furnished in prime or powder coat.
41⁄2 114.3 .180
5 127 .190
Available Sizes
Inches MM Gauge
TA795 Available Options:
A8121 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogFull Mortise Plain Bearing HingesFive Knuckle Standard Weight Series
33An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All standard weight full mortise non-ferrous hinges are packed with all machine x 1⁄2 wood screws. Steelhinges (except USP) are packed allmachine x all wood screws. For special screws consult price book on availability.
Packing:
Stainless steel base or available in brass or bronze base material polishedand plated or furnished in prime orpowder coat.
Steel base polished and plated or furnished in prime or powder coat finish.
• NRP (non-removable pin)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• BT (ball tip)• ST (steeple tip)• SSF (safety stud feature)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify T4314 or T4714)
Not recommended for medium or high frequency doors, or doors withclosing devices.
31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .134
41⁄2 x 41⁄2 114.3 x 114.3 .1345 x 41⁄2 127 x 114.3 .1465 x 5 127 x 127 .146
6 x 6* 152.4 x 152.4 .160
*Not available in Stainless
Available Sizes
Inches MM Gauge
T2314 T2714 Available Options:
A2133 Brass, BronzeA5133 StainlessA8133 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogFull Mortise Bearing HingesFive Knuckle Standard Weight Series
34 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
• NRP (non-removable pin)TB (ball bearing)
• TCA (concealed bearing)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• BT (ball tip)• ST (steeple tip)• SSF (safety stud feature)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available• CC (concealed circuit) 4, 6 or 8 wire
available*• CS- (concealed switch - handing required)*• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Slip In (Type 1 or Type 2)• Beveled Edge (where doors are beveled
on hinge side specify TA4314 or TA4714)
* Not available in Stainless
All standard weight full mortise non-ferrous hinges are packed with allmachine x 1⁄2 wood screws. Steelhinges (except USP) are packed allmachine x all wood screws. For special screws consult price book on availability.
Recommended for standard weight, medium frequency doors, or doors with closing devices.
Stainless steel base or available in brass or bronze base material polishedand plated or furnished in prime orpowder coat.
Steel base polished and plated or furnished in prime or powder coat finish.
31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .13441⁄2 x 41⁄2 114.3 x 114.3 .134
5 x 41⁄2 127 x 114.3 .1465 x 5 127 x 127 .1466 x 6* 152.4 x 152.4 .160
*Not available in Stainless
Available Sizes
Inches MM Gauge
TA2314 TA2714 Available Options:
A2112 Brass, BronzeA5112 StainlessA8112 Steel
ANSI Cross Reference:
Packing:
APPLICATION
McKINNEY Hinge CatalogWide Throw Full Mortise Bearing HingesFive Knuckle Standard Weight Series
35An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K standard weight full mortisewide throw hinges are packed with allmachine and 1⁄2 wood screws. For special screws consult price bookon availability.
Packing:
• NRP (non-removable pin)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• BT (ball tip)• ST (steeple tip)• SSF (safety stud feature)• RB (raised barrel)• QC (quick connect hinge) 2,4,6,8,10,
or 12 wire available*• CC-4 (concealed circuit - 4 wire)*
available on hinges up to 6 inches wide• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify TA4398 or TA4798)
* QC and CC options available on hinges upto 6" wide
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced and it is necessary to open the door around a large reveal.
Stainless steel base material polishedand passivated.
4 x 7 101.6 x 177.8 .13041⁄2 x 6 114.3 x 152.4 .13441⁄2 x 7 114.3 x 177.8 .13441⁄2 x 8 114.3 x 203.2 .134
5 x 7 127 x 177.8 .146
5 x 8 127 x 203.2 .146
Steel base material polished and plated or furnished in prime or powder coat.
Available Sizes
Inches MM Gauge
TA2398 TA2798
APPLICATION
Available Options:
A5112 StainlessA8112 Steel
ANSI Cross Reference:
McKINNEY Hinge CatalogFull Mortise Bearing HingesFive Knuckle Heavy Weight Series
36 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K heavy weight full mortise hingesare packed with all machine and 1⁄2wood screws. For special screws consultprice book on availability.
Packing:
• NRP (non-removable pin)• T4B (ball bearing)• TCA (concealed bearing)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• BT (ball tip)• ST (steeple tip)• SSF (safety stud feature)• RB (raised barrel)*• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available• CC (concealed circuit) 4, 6 or 8 wire
available**• CS- (concealed switch - handing required)**• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify T4A4386 or T4A4786)
*Refer to page 104 for raised barrel.** Not available in Stainless
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.
Steel material polished and plated orfurnished in prime or powder coat.
41⁄2 x 41⁄2 114.3 x 114.3 .180
5 x 41⁄2 127 x 114.3 .1905 x 5 127 x 127 .190
6 x 5 152.4 x 127 .203
6 x 6* 152.4 x 152.4 .203
8 x 6* 203.2 x 152.4 .2258 x 8* 203.2 x 203.2 .225
* Supplied in Bronze or Steel only
Stainless steel base or available in brass or bronze base materialpolished and plated or furnished in prime or powder coat.
Available Sizes
Inches MM Gauge
T4A3386 T4A3786 Available Options:
A2111 Brass, BronzeA5111 StainlessA8111 Steel
ANSI Cross Reference:
APPLICATION
Note: 8" x 6" and 8" x 8" have six bearings.
McKINNEY Hinge CatalogWide Throw Full Mortise Bearing HingesFive Knuckle Heavy Weight Series
37An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K full mortise heavy duty widethrow hinges are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book on availability.
Packing:
• NRP (non-removable pin)• T4B (ball bearing)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• BT (ball tip)• ST (steeple tip)• SSF (safety stud feature)• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify T4A4386 or T4A4786)
Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced.
Stainless steel base or available in brass or bronze base materialpolished and plated or furnished in prime or powder coat.
41⁄2 x 5 114.3 x 127 .180
41⁄2 x 6 114.3 x 152.4 .190
41⁄2 x 7 114.3 x 177.8 .19041⁄2 x 8 114.3 x 203.2 .180
5 x 6 127 x 152.4 .1905 x 7 127 x 177.8 .1905 x 8 127 x 203.2 .190
Steel base material polished and platedor furnished in prime or powder coat.
Available Sizes
Inches MM Gauge
T4A3386 T4A3786 Available Options:
A2111 Brass, BronzeA5111 StainlessA8111 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogSwing Clear Full Mortise Bearing HingesFive Knuckle Standard Weight Series (Reversible)
38 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K standard weight full mortisehinges are packed with all machine and 1⁄2 wood screws. For special screwsconsult price book on availability. Thepin is held in place by an NRP set screwwhich allows the hinge to be reversible.
Packing:
• TB (ball bearing)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• SSF (safety stud feature)• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify TA4895 or TA4395)
Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. Hinge allows for maximum clearance for passage of beds, tables or other equipment throughdoorway. Pressed steel jambs require no special reinforcing.
Stainless steel material or steel base material polished and plated or furnished inprime or powder coat.
41⁄2 114.3 .134
Available Sizes
Inches MM Gauge
TA2395 / TA2895 Available Options:
A8122 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogSwing Clear Full Mortise Bearing HingesFive Knuckle Heavy Weight Series (Reversible)
39An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K heavy weight full mortise hingesare packed with all machine and 1⁄2wood screws. For special screws consultprice book on availability. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.
Packing:
• T4B (ball bearing)• RC (round corner - 1⁄4" radius furnished
unless specified otherwise)• HT (hospital tip)• SSF (safety stud feature)• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specify T4A4395 or T4A4795)
Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. Hinge allows for maximum clearance for passage of beds, tables or other equipment throughdoorway. Pressed steel jambs require no special reinforcing.
Stainless steel material polished and passivated.
Steel base material polished and plated or furnished in prime or powder coat.
41⁄2 114.3 .1805 127 .190
Available Sizes
Inches MM Gauge
T4A3395 T4A3795 Available Options:
A5121 StainlessA8121 Steel
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogFull Mortise Steel HingesFive Knuckle Standard Weight Series
40 An ASSA ABLOY Group company An ASSA ABLOY Group companyNo
vem
ber
200
3
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
• NRP (non-removable pin)• Consult the factory for available finishes
Packed 3 each per box, 48 per carton.All machine x all wood screws.
Recommended for standard weight doors. For doors withclosing devices MPB 79, bearing hinge must be used.MacPro by McKINNEY templated hinges are made toconform to ANSI/BHMA 156.1, 156.7.
Plain bearing hinge. Steel base materialpolished and plated or furnished inprime coat.
Bearing hinge. Steel base polished andplated or furnished in prime coatfinish.
MP79 MPB79 Available Options:
A8112 SteelA8133 Steel
ANSI Cross Reference:
Packing:APPLICATION
41⁄2 x 41⁄2 114.3 x 114.3 .134
Available Sizes
Inches MM Gauge
McKINNEY Hinge CatalogFull Mortise Steel HingesFive Knuckle Standard Weight Series
40-a An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
• NRP (non-removable pin)
Packed 3 each per box, 48 per carton.All machine x all wood screws.
Recommended for standard weight , medium frequency doors,or doors with closing devices. MacPro by McKINNEYtemplated hinges are made to conform to ANSI/BHMA156.1, 156.7.
Bearing hinge. Stainless base polishedto a satin satin finish.
MPB91 Available Options:
• U32D Satin Stainless
Available Finishes
A5112 Stainless
ANSI Cross Reference:
Packing:
APPLICATION
41⁄2 x 41⁄2 114.3 x 114.3 .134
Available Sizes
Inches MM Gauge
McKINNEY Hinge CatalogFull Mortise Steel HingesFive Knuckle Standard Weight Series
40-bAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril2
003
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
• NRP (non-removable pin)• Consult the factory for available finishes
Packed 3 each per box, 48 per carton.All machine x all wood screws.
Recommended for use on high frequency and or heavy woodor metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. MacPro by McKINNEYtemplated hinges are made to conform to ANSI/BHMA156.1, 156.7.
Bearing hinge, stainless steel base,polished to a satin stainless finish.
Bearing hinge. Steel base polished andplated.
MPB99 Available Options:
A5111 StainlessA8111 Steel
ANSI Cross Reference:
Packing:
APPLICATION
41⁄2 x 41⁄2 114.3 x 114.3 .180
Available Sizes
Inches MM Gauge
MPB68
McKINNEY Hinge CatalogStandard Duty Center HungJamb Mount Pivot Set
41An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Interior or exterior doors up to:• 125 lbs• 3'6" x 8'0"*
Ferrous base pivot set polished and plated.
Recommended for use on average frequency double acting doors in schools,hospitals, institutions and other public buildings. Not for use on labeled doors and frames.
C07042
EP5-J
Aluminum 31⁄2 lbs 5 lbs
Wood - Particle Core 5 lbs 53⁄4 lbsWood - Stave Block Core 4 lbs 41⁄2 lbs14 Gauge Hollow Metal 83⁄4 lbs 10 lbs16 Gauge Hollow Metal 71⁄2 lbs 81⁄2 lbs18 Gauge Hollow Metal 61⁄2 lbs 71⁄2 lbs
Door Weight Chart(lbs per square foot)
Door Thickness13⁄4" 2"
• Thrust steel ball bearing in bottom pivot, oil impregnated bronze bearingin top pivot
• Center hung• Mortised into side jamb• Full mortise top pivot• Non-handed• Ferrous material• 15⁄32" radius heel edge of door
ANSI Cross Reference
Features:
Maximum Door Weight:
All EP5-J Pivot sets are packed with 14 x 11⁄2" wood screws and 1⁄4-20 x 5⁄8"machine screws
Packing:
McKINNEY Hinge CatalogFull Mortise Institutional HingesMaximum Security Protection Series
42 An ASSA ABLOY Group company An ASSA ABLOY Group companyOct
ob
er 2
005
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortiseinstitutional hinges are packed with allTorx Head Security machine screws.For special screws consult price bookon availability.
Packing:
• MM (magnetic monitoring)*• Beveled Edge (where doors are
beveled on hinge side specify
HTA5386 MSP-A or HTA5386 MSP-B
*Not available with PSF option
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where security requirements exist.
Set of three Hospital Tip hingesfeaturing concealed bearing assemblies.The top and bottom hinges arefurnished with Prison Safety Feature(PSF) and Safety Studs (SSF).
The middle hinge is not supplied withPSF or SSF
41⁄2 x 41⁄2 114.3 x 114.3 .1805 x 41⁄2* 127 x 114.3 .190
Set of three Hospital Tip hingesfeaturing concealed bearing assemblies.The top and bottom hinges arefurnished with Prison Safety Feature(PSF) and Safety Studs (SSF) - thethird hinge is furnished with QC8Electrolynx connectors.
The electric hinge is not furnishedwith PSF or SSF
Available Sizes
Inches MM Gauge
HTA386 MSP-A HTA386 MSP-B
PRISON SAFETY FEATURE (PSF)HOSPITAL TIP (HT)
Available Options:
A5111 Stainless
ANSI Cross Reference:
APPLICATION
McKINNEY Hinge CatalogFull Mortise Anchor Hinge SetThree Knuckle Heavy Weight Series
43An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortiseanchor hinge sets consist of one anchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for door header only, permits use of holders and closers concealed in the top of the jamb. The screws gointo the door header and are in shearpreventing the hinge from pulling loosefrom the door.
A2551 BronzeA5551 StainlessA8551 Steel
Packing:
• SSF (safety stud feature)• CC-4 (concealed circuit - 4 wire, center
hinge only)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available, center hinge only• CC (concealed circuit) 4, 6 or 8 wire
available, center hinge only*• CS- (concealed switch - handing
required, center hinge only)*• MM (magnetic monitoring, center
hinge only)• Beveled Edge (where doors are beveled
on hinge side specifyTA5391 or TA5791)
* Steel or Bronze base material only
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced. They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.
Stainless steel or bronze base materialpolished and plated or furnished inprime or powder coat.
5 x 41⁄2 127 x 114.3 .190
Available Sizes
Inches MM Gauge
Steel base material polished and platedor furnished in prime or powder coat.
For use with concealed door holders or door closersTA391 TA791
APPLICATION
ANSI Cross Reference
Available Options:
McKINNEY Hinge CatalogFull Mortise Anchor Hinge SetThree Knuckle Heavy Weight Series
44 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortiseanchor hinge sets consist of one anchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for jamb and door header permitsuse of surface applied holders andclosers. The screws are in shearpreventing the hinge from pulling loose from either the door or the jamb.
A2551 BronzeA5551 StainlessA8551 Steel
Packing:
5 x 41⁄2 127 x 114.3 .190
Available Sizes
Inches MM Gauge
• SSF (safety stud feature)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available, center hinge only• CC (concealed circuit) 4, 6 or 8 wire
available, center hinge only*• CS- (concealed switch - handing
required, center hinge only)*• MM (magnetic monitoring, center
hinge only)• Beveled Edge (where doors are beveled
on hinge side specifyTA5392 or TA5792)
* Steel or Bronze base material only
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced. They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.
Stainless steel or available in bronzebase material polished and plated orfurnished in prime or powder coat.
Steel base material polished and platedor furnished in prime or powder coat.
For use with surface applied door holders or door closersTA392 TA792
APPLICATION
ANSI Cross Reference
Available Options:
McKINNEY Hinge CatalogFull Mortise Anchor Hinge SetThree Knuckle Heavy Weight Series
45An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortiseanchor hinge sets consist of one anchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for jamb header only, permits useof holders and closers concealed in thetop of the door. The screws go into the jamb header and are in shearpreventing the hinge from pulling loose from the jamb.
A2551 BronzeA5551 StainlessA8551 Steel
Packing:
• SSF (safety stud feature)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available, center hinge only• CC (concealed circuit) 4, 6 or 8 wire
available, center hinge only*• MM (magnetic monitoring, center
hinge only)• Beveled Edge (where doors are beveled
on hinge side specifyTA5393 or TA5793)
* Steel or Bronze base material only
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced. They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.
Stainless steel or bronze base materialpolished and plated or furnished inprime or powder coat.
5 x 41⁄2 127 x 114.3 .190
Available Sizes
Inches MM Gauge
Steel base material polished and platedor furnished in prime or powder coat.
For use with concealed door holders or door closersTA393 TA793
APPLICATION
ANSI Cross Reference
Available Options:
McKINNEY Hinge CatalogFull Mortise Anchor Hinge SetThree Knuckle Heavy Weight Series
46 An ASSA ABLOY Group company An ASSA ABLOY Group companyjan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight full mortiseanchor hinge sets consist of one anchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for jamb and door header, permitsuse of surface applied holders andclosers. The screws are in shearpreventing the hinge from pulling loosefrom either the jamb or the door.
A2551 BronzeA5551 StainlessA8551 Steel
Packing:
5 x 41⁄2 127 x 114.3 .190
Available Sizes
Inches MM Gauge
• SSF (safety stud feature)• CC-4 (only)• QC (ElectroLynx hinge) 2, 4, 6, 8, 10
or 12 wire available, center hinge only• CC (concealed circuit) 4, 6 or 8 wire
available, center hinge only*• CS- (concealed switch - handing
required, center hinge only)*• MM (magnetic monitoring, center
hinge only)• Beveled Edge (where doors are beveled
on hinge side specifyTA5394 or TA5794)
* Steel or Bronze base material only
Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced. They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.
Stainless steel base or available inbronze base material polished andplated or furnished in prime or powder coat.
Steel base material polished and platedor furnished in prime or powder coat.
TA394 - 4" DOOR LEG TA794 - 4" DOOR LEG
APPLICATION
ANSI Cross Reference
Available Options:
McKINNEY Hinge CatalogHalf Mortise Plain Bearing HingesFive Knuckle Standard Weight Series (Reversible)
47An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K plain bearing standard weighthalf mortise hinges are packed with allmachine screws. For special screwsconsult price book on availability. Thejamb leaf is applied to the surface ofthe jamb with machine screws. Thedoor leaf is mortised into the edge ofthe door. The pin is held in place by anNRP set screw which allows the hingeto be reversible.
A8233 Steel
Packing:
• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyT4774)
Recommended for use on minimum frequency and/or light weight wood or stockhollow metal doors in residences, apartments or other very low frequency doors incommercial construction. The hinges may be used on channel iron jambs.
Note: Bearing hinges should be used on high and average frequency doors and on all doors equippedwith door closers and/or door holders.
Steel base material polished and plated or furnished in prime or powder coat.
T2774
41⁄2 114.3 .134
Available Sizes
Inches MM Gauge
APPLICATION
ANSI Cross Reference
Available Options:
McKINNEY Hinge CatalogHalf Mortise Bearing HingesFive Knuckle Standard Weight Series (Reversible)
48 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K standard weight half mortisehinges are packed with all machine screws. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf ismortised into the edge of the door. The pin is held in place by an NRP set screw which allows the hinge to be reversible.
A2212 BronzeA5212 StainlessA8212 Steel
Packing:
• TB (ball bearing)• TCA (concealed bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyTA4374 or TA4774)
Recommended for use on average frequency and/or medium weight wood or metaldoors in schools, hospitals or other public buildings where medium traffic isexperienced. The hinges may be used on channel iron jambs.
41⁄2 114.3 .134
5 127.0 .146
Available Sizes
Inches MM Gauge
Steel base material polished and platedor furnished in prime or powder coat.
TA2774
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
TA3374
ANSI Cross Reference
Available Options:
APPLICATION
McKINNEY Hinge CatalogHalf Mortise Bearing HingesThree Knuckle Standard Weight Series (Reversible)
49An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K standard weight half mortisehinges are packed with all machine screws. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf ismortised into the edge of the door. Thepin is held in place by an NRP set screwwhich allows the hinge to be reversible.
A2212 BronzeA5212 StainlessA8212 Steel
Packing:
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyTA5374 or TA5774)
Recommended for use on average frequency and/or medium weight wood or metaldoors in schools, hospitals or other public buildings where medium traffic isexperienced. The hinges may be used on channel iron jambs.
Steel base material polished and platedor furnished in prime or powder coat.
TA374 TA774
41⁄2 114.3 .1345 127.0 .146
Available Sizes
Inches MM Gauge
Available Options
ANSI Cross Reference
APPLICATION
McKINNEY Hinge CatalogHalf Mortise Bearing HingesThree Knuckle Heavy Weight Series (Reversible)
50 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight half mortisehinges are packed with all machine screws. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf is mortisedinto the edge of the door. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.
Packing:
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyTA5384 or TA5784)
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The hinges may be used on channel iron jambs.
41⁄2 114.3 .180
5 127.0 .1906* 152.4 .203
* Advise door thickness 13⁄4" or 21⁄4"
Available Sizes
Inches MM Gauge
Steel base material polished and platedor furnished in prime or powder coat.
TA384 TA784
A2211 BronzeA5211 StainlessA8211 Steel
ANSI Cross Reference
Available Options
APPLICATION
McKINNEY Hinge CatalogHalf Mortise Bearing HingesFive Knuckle Heavy Weight Series (Reversible)
51An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K heavy weight half mortisehinges are packed with all machine screws. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf is mortisedinto the edge of the door. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.
A2211 BronzeA5211 StainlessA8211 Steel
ANSI Cross Reference
Packing:
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
• T4B (ball bearing)• TCA (concealed bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyT4A4384 or T4A4784)
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The hinges may be used on channel iron jambs.
Steel base material polished and platedor furnished in prime or powder coat.
T4A3384 T4A3784
41⁄2 114.3 .1805 127.0 .1906* 152.4 .203
* Advise door thickness 13⁄4" or 21⁄4"
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogSwing Clear Half Mortise Bearing HingesThree Knuckle Heavy Weight Series (Reversible)
52 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K swing clear heavy weight halfmortise hinges are packed with allmachine screws for the door and 1⁄2 x 1⁄4-20 machine screws for thejamb leaf. For special screws consultprice book on availability. The jambleaf is applied to the surface of thejamb with machine screws. The doorleaf is mortised into the edge of thedoor. The pin is held in place by anNRP set screw which allows the hingeto be reversible.
A8221 Steel
ANSI Cross Reference
Packing:
Steel base material polished and plated or furnished in prime or powder coat. • HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyTA5789)
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tables or other equipment through door openings. These hinges may be used on channeliron frames.
TA789
APPLICATION
5 127.0 .190
Available Sizes
Inches MM Gauge
Available Options
McKINNEY Hinge CatalogSwing Clear Half Mortise Bearing HingesFive Knuckle Heavy Weight Series (Reversible)
53An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K swing clear heavy weight halfmortise hinges are packed with allmachine and 1⁄2 wood screws for thedoor and 1⁄2 x 1⁄4-20 machine screwsfor the jamb leaf. For special screwsconsult price book on availability. Thejamb leaf is applied to the surface ofthe jamb with machine screws. Thedoor leaf is mortised into the edge ofthe door. The pin is held in place by anNRP set screw which allows the hingeto be reversible.
A8221 Steel
ANSI Cross Reference
Packing:
Steel base material polished and plated or furnished in prime or powder coat. • T4B (ball bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Beveled Edge (where doors are beveled on hinge side specifyT4A4789)
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tables or other equipment through door openings. These hinges may be used on channeliron frames.
T4A3789
5 127.0 .190
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge Catalog
54 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
INTENTIONALLYLEFT
BLANK
McKINNEY Hinge CatalogHalf Surface Bearing HingesThree Knuckle Standard Weight Series (Reversible)
55An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
All 3K standard weight half surfacehinges are packed with all machine screws and 2 x 1⁄4-20 door bolts. Forspecial screws consult price book onavailability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacewith wood screws or grommet nuts andbolts. Specify if the door thickness isgreater than 13⁄4" to insure that properbolt is packed. The pin is held in placeby an NRP set screw which allows thehinge to be reversible.
Packing:
• Back Plate (BP-10)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on average frequency and/or medium weight wood or metal doors in schools, hospitals or other public buildings where medium traffic is experienced.
Steel base material polished and platedor furnished in prime or powder coat.
TA372 TA772
41⁄2 114.3 .1345 127.0 .146
Available Sizes
Inches MM Gauge
APPLICATION
A2212 BronzeA5212 StainlessA8212 Steel
ANSI Cross Reference
Available Options
McKINNEY Hinge CatalogHalf Surface Bearing HingesThree Knuckle Heavy Weight Series (Reversible)
56 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 3K heavy weight half surface hingesare packed with all machine screws anddoor bolts. For special screws consultprice book on availability. The jambleaf is fastened into the mortise withmachine screws. The door leaf isapplied full surface with wood screws or grommet nuts and bolts. Specify ifthe door thickness is greater than 13⁄4"to insure that proper bolt is packed.The pin is held in place by an NRP set screw which allows the hinge to be reversible.
Packing:
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
• Back Plate (BP-10)• TB (ball bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.
Steel base material polished and platedor furnished in prime or powder coat.
41⁄2 114.3 .1805 127.0 .190
6 152.4 .203*
Available Sizes
Inches MM Gauge
A2411 BronzeA5411 StainlessA8411 Steel
ANSI Cross Reference
Available Options
APPLICATION
TA382 TA782
* Not available in Stainless Steel
McKINNEY Hinge CatalogHalf Surface Plain Bearing HingesFive Knuckle Standard Weight Series (Reversible)
57An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K plain bearing standard weighthalf surface hinges are packed with allmachine screws and 2 x 1⁄4-20 doorbolts. For special screws consult pricebook on availability. The jamb leaf isfastened into the mortise with machinescrews. The door leaf is applied fullsurface with wood screws or grommetnuts and bolts. Specify if the doorthickness is greater than 13⁄4" to insurethat proper bolt is packed. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.
Packing:
• Back Plate (BP-10)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Steel base material polished and plated or furnished in prime or powder coat.
41⁄2 114.3 .134
Available Sizes
Inches MM Gauge
Recommended for use on minimum frequency and/or light weight wood or stockhollow metal doors in residences, apartments or other very low frequency doors incommercial construction. The hinges may be used on channel iron jambs.
Note: Bearing hinges should be used on high and average frequency doors andon all doors equipped with door closers and/or door holders.
A8433 Steel
ANSI Cross Reference
Available Options
APPLICATION
T2772
McKINNEY Hinge CatalogHalf Surface Bearing HingesFive Knuckle Standard Weight Series (Reversible)
58 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K standard weight half surfacehinges are packed with all machine screws and 2 x 1⁄4-20 door bolts. Forspecial screws consult price book onavailability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacewith wood screws or grommet nuts andbolts. Specify if the door thickness isgreater than 13⁄4" to insure that properbolt is packed. The pin is held in placeby an NRP set screw which allows thehinge to be reversible.
Packing:
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
• Back Plate (BP-10)• TB (ball bearing)• TCA (concealed bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on average frequency and/or medium weight wood or metaldoors in schools, hospitals or other public buildings where medium traffic isexperienced.
Steel base material polished and platedor furnished in prime or powder coat.
TA2372 TA2772
41⁄2 114.3 .1345 127.0 .146
Available Sizes
Inches MM Gauge
A2412 BronzeA5412 StainlessA8412 Steel
ANSI Cross Reference
Available Options
APPLICATION
McKINNEY Hinge CatalogHalf Surface Bearing HingesFive Knuckle Heavy Weight Series (Reversible)
59An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 5K standard weight half surfacehinges are packed with all machine screws and 2 x 1⁄4-20 door bolts. Forspecial screws consult price book onavailability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacewith wood screws or grommet nuts andbolts. Specify if the door thickness isgreater than 13⁄4" to insure that properbolt is packed. The pin is held in placeby an NRP set screw which allows thehinge to be reversible.
Packing:
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
• Back Plate (BP-10)• TB (ball bearing)• TCA (concealed bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.
Steel base material polished and platedor furnished in prime or powder coat.
T4A3382 T4A3782
41⁄2 114.3 .1805 127.0 .1906* 152.4 .203
* Not available in Stainless Steel or TCA
Available Sizes
Inches MM Gauge
A2411 BronzeA5411 StainlessA8411 Steel
ANSI Cross Reference
Available Options
APPLICATION
McKINNEY Hinge CatalogSwing Clear Half Surface Bearing HingesThree Knuckle Heavy Weight Series (Reversible)
60 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Steel base material polished and plated or furnished in prime or powder coat. • HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
All 3K swing clear heavy weight halfsurface hinges are packed with allmachine and 1⁄2 wood screws for thedoor and 1⁄2 x 1⁄4-20 machine screwsfor the jamb leaf. For special screwsconsult price book on availability. Thejamb leaf is applied to the surface ofthe jamb with machine screws. Thedoor leaf is mortised into the edge ofthe door. The pin is held in place by anNRP set screw which allows the hingeto be reversible.
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tables orother equipment through door openings.
TA796
APPLICATION
5 127.0 .190
Available Sizes
Inches MM Gauge
A8421 Steel
ANSI Cross Reference
Available Options
Packing:
McKINNEY Hinge CatalogSwing Clear Half Surface Bearing HingesFive Knuckle Heavy Weight Series (Reversible)
61An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Steel base material polished and plated or furnished in prime or powder coat. • T4B (ball bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
All 5K swing clear heavy weight halfsurface hinges are packed with allmachine and 1⁄2 wood screws for thedoor and 1⁄2 x 1⁄4-20 machine screwsfor the jamb leaf. For special screwsconsult price book on availability. Thejamb leaf is applied to the surface ofthe jamb with machine screws. Thedoor leaf is mortised into the edge ofthe door. The pin is held in place by anNRP set screw which allows the hingeto be reversible.
Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tables orother equipment through door openings.
T4A3796
5 127.0 .190
Available Sizes
Inches MM Gauge
A8421 Steel
ANSI Cross Reference
Available Options
Packing:APPLICATION
McKINNEY Hinge Catalog
62 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
INTENTIONALLYLEFT
BLANK
McKINNEY Hinge CatalogFull Surface Bearing HingesThree Knuckle Heavy Weight Series
63An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06A2311 BronzeA5311 StainlessA8311 Steel
ANSI Cross Reference
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24)* screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".
• HT (hospital tip)
Recommended for use on high frequency and/or heavy weight wood or Kalameindoors in schools, hospitals or other public buildings where medium traffic prevails.The hinges may be used on channel iron frames.
Steel base material polished and platedor furnished in prime or powder coat.
TA381 TA781
41⁄2 114.3 .134
5 127.0 .146
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogFull Surface Bearing HingesFive Knuckle Heavy Weight Series
64 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06 A2311 BronzeA5311 StainlessA8311 Steel
ANSI Cross Reference
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24)* screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".
* (1⁄2x1⁄4-20 provided on 6")
• T4B (ball bearing)• TCA (concealed bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on high frequency and/or heavy weight wood or Kalameindoors in schools, hospitals or other public buildings where medium traffic prevails.The hinges may be used on channel iron frames.
Steel base material polished and platedor furnished in prime or powder coat.
T4A3381 T4A3781
41⁄2 114.3 .134
5 127.0 .1466* 152.4 .203
* Not available in Stainless Steel
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogFull Surface Bearing HingesThree Knuckle Standard Weight Series
65An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06A8312 Steel
ANSI Cross Reference
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24) screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".
• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on standard weight and/or medium frequency doors inschools, hospitals or other public buildings where medium traffic prevails. Thehinges may be used on channel iron frames.
Steel base material polished and platedor furnished in prime or powder coat.
TA371 TA771
41⁄2 114.3 .134
5 127.0 .146
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogFull Surface Bearing HingesFive Knuckle Standard Weight Series
66 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06 A8312 Steel
ANSI Cross Reference
Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inprime or powder coat.
The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24) screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".
• TB (ball bearing)• TCA (concealed bearing)• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on standard weight and/or medium frequency doors inschools, hospitals or other public buildings where medium traffic prevails. Thehinges may be used on channel iron frames.
Steel base material polished and platedor furnished in prime or powder coat.
TA2371 TA2771
41⁄2 114.3 .1345 127.0 .146
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogFull Surface Swing Clear Bearing HingesThree Knuckle Heavy Weight Series
67An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06A8321 Steel
ANSI Cross Reference
The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x1⁄4-20) screws and the door leaf isapplied to the surface of the door withwood screws (1x1⁄4-14) or grommetnuts and bolts (2x1⁄4-20). Specify doorthickness if greater than 13⁄4".
• HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on high frequency and/or heavy weight wood or Kalameindoors in hospitals or other institutions where heavy traffic prevails. This hingeallows for the maximum clearance for passage of beds, tables and other equipmentthrough the doorway.
Steel base material polished and plated or furnished in prime or powder coat.
TA797
5 127.0 .190
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogFull Surface Swing Clear Bearing HingesFive Knuckle Heavy Weight Series
68 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06 A8321 Steel
ANSI Cross Reference
The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x1⁄4-20) screws and the door leaf isapplied to the surface of the door withwood screws (1x1⁄4-14) or grommetnuts and bolts (2x1⁄4-20). Specify doorthickness if greater than 13⁄4".
• T4B (ball bearing) • HT (hospital tip)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
Recommended for use on high frequency and/or heavy weight wood or Kalameindoors in hospitals or other institutions where heavy traffic prevails. This hingeallows for the maximum clearance for passage of beds, tables and other equipmentthrough the doorway.
Steel base material polished and plated or furnished in prime or powder coat.
T4A3797
5 127.0 .190
Available Sizes
Inches MM Gauge
Available Options
APPLICATION
McKINNEY Hinge CatalogFull Mortise Single ActingStandard Weight Spring Hinge
69An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 1502 and 1552 series standardweight single acting spring hingesare packed with all machine and 1⁄2wood screws. For special screws consultprice book on availability. This non-handed hinge series has infiniteadjustment and tension can be addedor reduced by means of a hex keywhich is provided. Locking screwprovides tamper-resistance after theproper tension has been set. Forunparalled tamper resistance andsecurity choose our TRS option. Twonylon tee bearings for vertical andlateral loads. Coil spring providesclosing power.
Packing:
• RC (round corner - 1⁄4" radius furnished unless specified otherwise
• HT (hospital tip - on one side only*)• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
• Reverse Spring Option 1502-R*(Maintains the door in the open position)
• TRS (tamper resistant option) for additional security. A tamper resistant screw is screwed into the tension ratchet after the proper tension has been set.
* Voids the UL® listing
Recommended for standard weight, medium frequency doors in place of doorclosers in apartments, hotels, motels, office buildings, etc.
Caution: Use of gasket for smoke or sound protection, wind condition ofunbalanced air pressure may prevent door from latching. Additional closingpower would be required. NFPA requires a minimum of two (2) spring hingeson labeled doors.
4 x 4* 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .134
41⁄2 x 41⁄2 114.3 x 114.3 .134*4 x 4 not available in stainless.
Available Sizes
Inches MM Gauge
K81071 SteelK81071F SteelK51071 Stainless SteelK51071F Stainless Steel
ANSI Cross Reference
Available Options
APPLICATION
1502 1552
C USLISTED
Steel base material polished and plated orfurnished in prime or powder coat.
Stainless steel material polishedand passivated.
McKINNEY Hinge CatalogFull Mortise Single ActingStandard Weight Spring Hinge Set
70 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 1522 sets of standard weight singleacting spring hinges are furnished withtwo 1502 and one 1500 (springless)hinge with all machine and 1⁄2 woodscrews. For special screws consult pricebook on availability. This non-handedhinge series has infinite adjustmentand tension can be added or reducedby means of a hex key which isprovided. Locking screw providesunparalleled tamper-resistance after theproper tension has been set. Two nylontee bearings for vertical and lateralloads. Coil spring provides closingpower.
Packing:
Steel base material polished and plated or furnished in prime or powder coat finish. • RC (round corner - 1⁄4" radius furnished unless specified otherwise
• HT (hospital tip - on one side only*)• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
* Voids the UL® listing
Recommended for standard weight, medium frequency doors in place of doorclosers in apartments, hotels, motels, office buildings, etc.
Caution: Use of gasket for smoke or sound protection, wind condition ofunbalanced air pressure may prevent door from latching. Additional closingpower would be required. NFPA requires a minimum of two (2) spring hingeson labeled doors.
1522
4 x 4 101.6 x 101.6 .130
41⁄2 x 4 114.3 x 101.6 .134
41⁄2 x 41⁄2 114.3 x 114.3 .134
Available Sizes
Inches MM Gauge
K81071 SteelK81071F Steel
ANSI Cross Reference
Available Options
APPLICATION
C USLISTED
McKINNEY Hinge CatalogHalf Surface Single ActingStandard Weight Spring Hinge
71An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 1572 Series Standard Weight SingleActing Spring Hinges are packed withall machine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. This non-handed hingeseries has infinite adjustment andtension can be added or reduced bymeans of a hex key which is provided.Locking screw provides unparalleledtamper-resistance after the propertension has been set. Two nylon teebearings for vertical and lateral loads.Coil spring provides closing power.
Packing:
Steel base material polished and plated or furnished in prime or powder coat finish. • RC (round corner - 1⁄4" radius furnished unless specified otherwise
• HT (hospital tip - on one side only*)• MM (magnetic monitoring)• “S” (sherardizing, our additional rust
resistant base under prime coat onsteel base)
* Voids the UL® listing
Recommended for standard weight, medium frequency doors in place of doorclosers in apartments, hotels, motels, office buildings, etc.
Caution: Use of gasket for smoke or sound protection, wind condition ofunbalanced air pressure may prevent door from latching. Additional closingpower would be required. NFPA requires a minimum of two (2) spring hingeson labeled doors.
1572
41⁄2 x 41⁄2 114.3 x 114.3 .134
Available Sizes
Inches MM Gauge
K81081 SteelK81081F Steel
ANSI Cross Reference
Available Options
APPLICATION
C USLISTED
McKINNEY Hinge CatalogHeavy Duty Double ActingSpring Butt Hinge
72 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Specification ScheduleMaximum Door Thickness 13⁄4" 13⁄4"
# of Hinges for Each Door 2 3
Maximum Door Width 3’0" 4’0"
Door Height* 8 to 9’ 8 to 9’
Maximum Door Weight 265 320
The application is simplified andmore secure by fastening the jambflange directly to the jamb without ahanging strip. The door flange ismortised into the door. If desired thejamb flange may be applied to thesurface of the jamb with a mortise inthe door sufficient to receive thethickness of both flanges. Thisapplication eliminates a filler strip andis used frequently on channel ironframes. This hinge is packed withhexagonal head bolts and nuts for theclamp flange and machine screws forthe jamb flange.
K61091 Cast Iron
ANSI Cross Reference
• Due to its heavy construction, the CS1 is useful in preventing door oscillations in extreme and variable draft conditions
• Heavy cast malleable iron with two axis’s which permit the door to open 180˚
• Hinge pins are securely held in place by a set screw
• Spring is protected from damage inside the all cast malleable construction
• Door and frame should be prepped using the installation instructions provided with the unit
Features:
When estimating the weight ofdoors, be sure to include (with theexception of hinges) all hardware,metal plates and buffers. For hollowmetal doors or wood doors over 3' widewith heavy metal plates, we recommendthree hinges for each door to avoidpossible sagging. The third hingeshould be placed near the top hinge butallow space for pin removal. The use ofHi-Duty Spring Steel Buffers will inmost installations protect the doorwithout use of heavy metal plates. Thiswill reduce the weight of the door andload on the hinges. Spring Steel Buffersillustrated on next page.
For replacement spring, order H15 Spring.
Recommended for use on high frequency and/or heavy wood or metal trucking doorsin post offices, warehouses or other buildings where heavy traffic is experienced.
APPLICATION
* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.
Cast malleable iron furnished in PC (Prime Powder Coat) or AP or D4 finish.
CS1
McKINNEY Hinge CatalogHeavy Duty Spring Steel Buffer
73An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Steel base material polished andfurnished in Nickel Plate.
McKINNEY type 35 spring steelbuffers are recommended where thereare two doors to a doorway which arehung as double-acting. This size bufferis suitable to any width door and
applicable to any height. Buffer shouldbe applied backset from edge of doorone inch. Specify thickness of door toindicate length of fastening boltsrequired. Also advise if application isfor one side of door only to insure thatproper fastening is supplied.
35
K87431 Steel
ANSI Cross Reference
• Used to prevent door and hinges from being damaged on trucking doorways where violent use is involved
• Buffer is constructed of an 8" wide spring steel band, strong enough to resist heavy shock
• Furnished 4 buffers and keepers per set• Available for one side of door application
Features:
It is recommended that if truck bumpers are of various heights, apply two or threebuffers, one above the other.
APPLICATION
Suggested for use with CS1, Heavy Duty Double Acting Spring Butt Hinge,illustrated on previous page.
McKINNEY Hinge CatalogHeavy Duty Adjustable Tension SimplexFull Surface Double Acting Door Spring
74 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
450 SERIES
K87441 Steel
ANSI Cross Reference
• Coil springs made of high grade steel wire• Adjustable tension, no special tools required• Wrought steel brackets prevent breakage• Economical• Simplified method of closing doors
Features:
All 450 Series are finished in 1D(black) and are packed with 1x12wood screws. This economical series isdesigned to be surface applied to thedoor and frame.
Dimensions
Number 451 452 453
Overall Length 9" 11" 13"
Packing:
McKINNEY Hinge CatalogSimplex Full Mortise Double Acting Spring Butt-Hinge
75An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All 1001 Series Double Acting SpringHinges are packed all machine x 1⁄2wood screws. This hinge is designed tobe applied directly to the jamb withoutthe use of a hanging strip. Door flangerequires a shallow mortise.
Packing:
1001
K81041 Steel
ANSI Cross Reference
• For wood doors not weighted with plate glass or heavy hardware
• Door flange mortised in door• Jamb Flange Surface applied to the
frame face• Non-templated (sizes 3", 4", 5", 6")• Springs are made of high grade
tempered steel• Non-handed
Features:
It is recommended that three hinges be used on door sizes as indicated above. The center hinge should be installed as close as possible to the top hinge for maximum support.
Steel base material polished and plated or furnished in prime coat finish.
Approximate Dimensions in InchesA Length of Door Flange
(size of hinge) 3 4 5 6
B Minimum Thickness of Door 3⁄4 7⁄8 11⁄8 11⁄4C Maximum Thickness of Door
with Chamfering 1 11⁄4 11⁄2 13⁄4
D Maximum Thickness of Doorwithout Chamfering for Metal Doors 7⁄8 11⁄8 13⁄8 13⁄4
Door SpecificationsMinimum 3⁄4" x 2’2" to 7⁄8" x 2’2" to 11⁄8" x 2’4" to 11⁄4" x 2’6" toMaximum 1" x 2'0" 11⁄4" x 2’0" 11⁄2" x 2’2" 13⁄4" x 2’4"
Maximum Door Sizes and Weights2 Hinges Per Door 3 Hinges Per Door
Catalog Number Door Weight Lbs. Door Width Door Weight Lbs. Door Width Door Height*
1001 3" 35 2’0" 40 2’8" 5’0"
1001 4" 60 2’4" 75 3’0" 6’8"
1001 5" 65 2’8" 90 3’0’ 6’8"
1001 6" 72 2’8" 105 3’0" 7’0"
* Minimum height for weights shown. Hinge capacity decreases as door height decreases.
APPLICATION
McKINNEY Hinge CatalogSimplex Full Mortise Double Acting Spring Butt-Hinge
76 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
APPLICATION
All 6x41⁄2"1001 Series Double ActingSpring Hinges are packed all machine x1⁄2 wood screws. This hinge is designedto be applied directly to the jambwithout the use of a hanging strip.Door flange requires a shallow mortise.
Packing:
K81151 Steel
ANSI Cross Reference
1001 6 X 41⁄2
• For stock hollow metal or wood doors that are 13⁄4" thick
• Door flange designed to fit standard 41⁄2x41⁄2" template mortise
• Jamb Flange Surface applied to the frame face
• Springs are made of high grade tempered steel
• Non-handed
Features:
It is recommended that three hinges be used on door sizes as indicated above.These listed weights include a margin of safety. Minimum clearance required onedge of door and frame on lock side. Hinge side clearance, allow 1⁄4" per doorbecause of jamb flange and hinge body not being mortised. The center hingeshould be installed as close as possible to the top hinge for maximum support.Hinge capacity decreases as door height decreases.
Steel base material polished and plated or furnished in prime coat finish.
Specification Schedule for Door 7’ High or MoreMax Door Weight* Lockside Clearance*
Door Width 2 Each 3 Each Flat Edge Round Edge
2’0" 96 145 1⁄4" 1⁄16"
2’2" 89 135 3⁄16" 1⁄16"
2’6" 77 125 3⁄16" 1⁄16"
2’8" 72 115 1⁄8" 1⁄16"
3’0" 64 105 1⁄8" 1⁄16"
*Minimum height for weights shown. Hinge capacity decreases as door height decreases.
McKINNEY Hinge CatalogSimplex Full Mortise Double Acting Spring Butt-Hinge
77An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
APPLICATION
9001
K81041 Steel
ANSI Cross Reference
• For wood or metal doors of heavy construction. Note: For stock hollow metal doors, use 6x41⁄2 1001
• Jamb Flange Surface applied to the frame face
• Springs are made of high grade tempered steel
• Non-handed
Features:
It is recommended that three hinges be used on door sizes as indicated above. The center hinge should be installed as close as possible to the top hinge formaximum support.
All 9001 Series Double Acting SpringHinges are packed all machine x 1⁄2wood screws. For special screws consultprice book on availability. This hinge isdesigned to be applied directly to thejamb without the use of a hangingstrip. Door flange requires a deepermortise than a 1001.
Steel base material polished and plated or furnished in prime coat finish.
Specifications for 8" 9001Door Weight Door Width # Hinges/Door
103 3’6" 2
143 4’0" 3
11⁄2" to 2" Door Thickness7’0" Door Height*
* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.
Packing:
McKINNEY Hinge CatalogSimplex Double Acting Clamp Flange Spring Butt-Hinge
78 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
19001
K81111 Steel
ANSI Cross Reference
• Designed for use on trucking doorways• Springs are made of high grade
tempered steel• Channels are spot welded and riveted to
flange for additional strength
Features:
If doors are extra heavy, we recommend three hinges per door. The third hingeshould be installed as close as possible to the top hinge as conditions will permit formaximum support. For doors subjected to severe shock, we recommend the CS1Spring Hinge.
All 19001 Series Double Acting SpringHinges are packed with Hex Headthrough bolts, nuts and all woodscrews. The clamp flange is attached tothe door surface with through bolts forgreater security of fastenings.
Steel base material polished and plated or furnished in prime coat finish.
Specifications for 8" 19001Door Weight Door Width # Hinges/Door
100 3’6" 2
140 4’0" 3
Minimum 31⁄2" Door Style Width7’0" Door Height*
* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.
APPLICATION Packing:
McKINNEY Hinge CatalogSimplex Half Surface Double Acting Spring Butt-Hinge
79An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
HS1001
K81131 Steel
ANSI Cross Reference
• For thin plywood doors or gates where screws will not hold in edge of door
• Does not require a hanging strip• Non-Templated (sizes 3", 4")• Springs are made of high grade
tempered steel• Non-handed
Features:
It is recommended that three hinges be used on door sizes as indicated above. The center hinge should be installed as close as possible to the top hinge formaximum support.
All Half Surface 1001 Series DoubleActing Spring Hinges are packed withall wood screws. This hinge is designedfor one flange to be applied to thesurface of door and other to the surfaceof jamb.
Steel base material polished and plated or furnished in prime coat finish.
Specifications for 3" HS1001Door Weight Door Width # Hinges/Door
35 2’0" 2
38 2’8" 33⁄4" to 1" Door Thickness5'0" Door Height*
* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.
Specifications for 4" HS1001Door Weight Door Width # Hinges/Door
60 2’8" 2
75 3’0" 37⁄8 to 11⁄4" Door Thickness6'8" Door Height*
* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.
APPLICATION Packing:
McKINNEY Hinge CatalogAjax Double Acting Horizontal Spring Pivot Hinge
80 An ASSA ABLOY Group company An ASSA ABLOY Group companyAu
gu
st 2
004
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Furnished painted or in finely plated finish.
This hinge is equipped with a 90˚ hold open feature, hardened steel roller bearingsand slotted screws that hold in the floor plate to permit easy alignment. It also hasadjustable tension and nylon top pivot and socket.
Application of attaching plate and hinge to the bottom of door is very simple andrequires only a rectangular mortise cut.
3001-STEEL / J3001-STEEL
• For use on hollow metal or wood doors in residences, restaurants and other public places
• All wood screws• Optional jamb attaching plate for
concrete or tile floor (to order, prefix “J” to number)
Features:
Specifications for 3001Door Thickness 11⁄8" to 13⁄4"
Door Weight 90
Door Width 3'0"
McKINNEY Hinge CatalogSagless Double Acting Gate Spring Pivot Hinge
81An ASSA ABLOY Group company An ASSA ABLOY Group company Au
gu
st 2
004
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Furnished painted or in finely plated finish.
Has an exterior tension adjustmentwhich can be adjusted after hinge isapplied. Anti-friction bearing to carrythe weight of the gate and an anti-friction bearing in the top socketwhich reduces friction and wear. The
pintle has an adjustment in the bottomattachment with a locking devicewhich permits aligning the gate orsetting the gate in desired position.Spring is large enough for heavy dutyconditions but the adjustable tensionmakes it equally suited for light gates.
The 4007 RB Series attachmentsare applied to the surface of the frame
and the box is applied to the bottomsurface of the gate. However, in the4007MRB Series, the box is mortisedinto the bottom of the gate.
Specify MRB for mortised box andreversed brackets; specify RB forreverse brackets only.
Before ordering, please noteclearances in chart.
4007RB-MALLEABLE IRON 4007MRB-MALLEABLE IRON
• For use on wood and metal gates• All wood screws• Exterior tension adjustment• Anti-friction bearings• Pintle adjustment with locking device
Features:
Clearances
Catalog # 4007MRB 4007RB
Minimum Clearance Under Gate 23⁄8" 4"
Gate or Handrail Thickness 11⁄8 -21⁄2" 11⁄8 -21⁄2"
Weight of Gate 75 75
Width of Gate 3'6" 3'6"
Width of Jamb Attachment 11⁄4" 11⁄4"
* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.
McKINNEY Hinge CatalogLightweight Double Acting Gravity Pivot Hinge
82 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Furnished painted or in finely plated finish.
The 8007 features a unique ballbearing pivot riding on a hardenedsteel cam providing frictionless longlasting service. The H8007 is similar tothe 8007 except that it has a 90˚ holdopen feature in either direction.
Attachments are surface applied tothe jamb and the top socket may besurface applied or mortised into the topof the door. The box may be surfaceapplied or mortised into the bottom ofthe door.
8007-STEEL / H8007-STEEL
• For use on double acting wood Louvre doors 3⁄4" to 13⁄4" thick which do not exceed 18" in width, 5' in height or 40lbs in weight
Features:
Specifications for 8007/H8007Door Thickness 3⁄4" to 13⁄4"
Door Weight 40
Door Width 1'6"
Door Height* 5'0"
* Maximum height for weights shown. Hinge capacitydecreases as gate height decreases.
McKINNEY Hinge CatalogHinge Back Plate
83An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Furnished painted or in finely plated finish.
BP-10 / BP-11 / BP-12
McKINNEY Hinge CatalogCombination Strike and Stop
84 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
CSS-9
All Combination Strike and Stops arepacked with 1⁄2 x 8-32 machine screws.
.095 gauge brass material polished and plated. Manufactured for use withcylindrical or bored locks.
• Available in offset or center hung latch bolt location for frame sizes 53⁄4" and 63⁄4"
Features:
Packing:
Recommended for installations on hospital or nursing home toilet doors along with our EP5-J. This unit allows center hung or 1⁄8" inset doors to be opened inboth directions without damaging the frame.
APPLICATION
OFFSET HUNG CENTER HUNG
May not work with mortise locks. Consult the factory for mortise lock application.
McKINNEY Hinge CatalogEmergency Door Stop
85An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Bronze material polished and plated, rubber bumper insert encased in high impactABS plastic case.
DS-6
APPLICATION
Recommended for installation with our EP-5J pivot in schools, hospitals,institutions and other public buildings. This unit allows center hung or 1⁄8" inset doors to be opened in both directions without damaging the frame.
All Combination Strike and Stops arepacked with 1⁄2 x 8-32 machine screws.
• Used to convert double acting doors hung on center pivots to single acting doors
• Emergency release allows door to swing open in the opposite direction
• Mortise only on frame• Latch releases with a touch of the finger• Second touch of lever returns latch to
original position
Features:
A1882 Bronze
ANSI Cross Reference
Specifications for DS-6
Size of Surface Plate 41⁄2" x 15⁄8"
Bolt Length 2"
Size of Case 21⁄8" x 15⁄16"
Packing:
McKINNEY Hinge CatalogDouble Lipped Strike
86 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
06
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All Double Lipped Strikes are packedwith 1⁄2 x 8-32 machine screws.
.095 gauge brass material polished and plated. Manufactured for use withcylindrical or bored locks.
Packing:
DLS-8
Recommended for installations on hospital or nursing home toilet doors along with our EP5-J and DS-6 Emergency Stop. This unit allows center hung or 1⁄8" inset doors to be opened in both directions without damaging the frame.
• Available in offset or center hung• Latch bolt location for frame sizes 53⁄4"
and 63⁄4"
Features:
APPLICATION
Center Hung Shown
May not work with mortise locks. Consult the factory for mortise lock application.
McKINNEY Hinge CatalogElectroLynx Hinge (QC Option)
87An ASSA ABLOY Group company An ASSA ABLOY Group company Jun
e 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
The McKinney ElectroLynx Hingeis an intermediate connector whichpasses a constant flow of currentbetween the source of power (jamb)and the actuated devices in the door(i.e. electric locks, exit devices, etc.)regardless of door position.
Each hinge features concealed plugconnectors which eliminate the needfor separate or exposed wiring. Brasseyelets add protection and durability tothe ElectroLynx Hinge and commonwire colors and standard connectorsmake installation quick and simple.
The ElectroLynx Hinge should beinstalled in the center position on thedoor. Once installed, it will give nooutward indication of its function andwill transmit power efficiently andreliably, as long as the wire capacity isnot exceeded.
All ElectroLynx Electric Hinges arefactory tested and specially packaged tominimize against damage duringshipment. Installation instructions arepacked with each hinge.
28 Gauge multi-strand wires areused. A pigtail is provided forconnection to the source wiring. Thewire colors are coordinated to workwith other ASSA ABLOY Companieselectro-mechanical hardware.
An 8 position connector is used forQC2, QC4, QC6 and QC8 wirehinges. An 8 position and 4 positionconnector is used for QC12 wirehinges. A QC2A wire hinge isavailable for power on, power off applications.
QC
• Available up to 12 wires• Rated 1 Amp Capacity• Can be used in conjunction with CS hinge
(QC8 wire maximum)* on most 5 Knuckle full mortise hinges
• Can be used with MM option on most 5 knuckle full mortise hinges*
• Optional MG-16 mortar guard available (mortar guard required on steel frames)
• QC2 wire hinges provided with 8 position connector for new construction , specify QC2
* Refer to individual catalog pages regardingthe availability of these options
Features:
UNDERWRITERSLABORATORYLISTED
APPLICATION
McKINNEY Hinge CatalogConcealed Circuit Electric Hinge (CC Option)
88 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
The McKINNEY Concealed CircuitHinge is an intermediate connectorwhich passes a constant flow of currentbetween the source of power (jamb)and the actuated devices in the door(i.e. electric locks, exit devices, etc.)regardless of door position.
The color of the wires assists inmaintaining proper circuit hookupbetween the power source and actuateddevices during installation.
CC Electric Hinges should beinstalled in the center position on thedoor. Once installed, it will give nooutward indication of its function andwill transmit power efficiently andreliably, as long as the wire electricalcapacity is not exceeded.
All CC Electric Hinges are factorytested and specially packaged to insureagainst damage during shipment.Installation instructions are packedwith each hinge.
28 gauge multi-strand wire is used. Itis recommended that care be exercisedduring connection of the leads andinstallation of the hinge to avoid wire damage.
The CC feature is available on mosttwo, three and five knuckle fullmortise contract grade hinges. Consultthe individual catalog pages for thisoption feature.
CC
• Available with 2, 3 or 4 circuits• 1 Amp, 24 Volts maximum each circuit
continuous duty, 16.0 Amps intermittentduty (pulse)
• Can be used in conjunction with CS or MM option on most full mortise hinges
• Optional mortar guard MG-16 available• Electric feature undetectable when hinge
is installed
Features:
Wire Capacity
4 Wires 2 Circuits
6 Wires 3 Circuits
8 Wires 4 Circuits
UNDERWRITERSLABORATORYLISTED
APPLICATION
REAR VIEW
McKINNEY Hinge CatalogAluminum Continuous Electrified Hinge (SER & ACC Options)
89An ASSA ABLOY Group company An ASSA ABLOY Group company Oct
ob
er 2
005
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
The McKINNEY electrified continuous hinge is furnished with bonded, 4- conductorflat cable with connectors at each leaf. Each 4-conductor cable is able to carry 4amps @ 24 volts with a 16 amp in-rush current for 300 milliseconds. To protect thecable from any overload or surge in power, each hinge is supplied with a 4 amp in-line fuse. And a wire harness is supplied with each hinge as a standard.
Two options allow variable degrees of service to be performed at the specificlocation of the current carrying cables via either a removable 8" or a pivoting 8"section of the hinge. Both of these options, SER and ACC are available as QC4, 8or 12 wire configurations on our Full Mortise Aluminum Continuous Hinges.
SER & ACC OPTIONS
• Performance tested 1,250,000 cycles withthe 4 conductor flat cable
• Each 4-conductor cable carries 4 amps @ 24volts with a 16 amp inrush current for 300milliseconds
• Each hinge is provided with a 4 amp in-linefuse to protect the cable from any overloador surge in power
• Flat cable conductor is warranted 5 years• Each electrical prep is supplied with a 36"
and 72" wire harness• Available on Full Mortise Aluminum
Continuous Hinges• Works with other ASSA ABLOY
ElectroLynx Products• Electrical modification meets new SDI
location at center of hinge
Features:
The hinge is furnished to be installedin three sections, allowing the currentcarrying cables to be serviced orreplaced without removing the doorfrom the frame.
Additionally the SER option allows thecurrent carrying cables to be safelystored or delivered to the electrician orsecurity contractor prior to theinstallation of the electrified hardware,eliminating the necessity of theelectrician or security contractor beingpresent when the doors are being hung. Product Number Example:83"MCK25HD CL x –SER-8*
*hinges are handed
SERVICEABLE/REMOVABLE (SER)
The hinge is furnished to be installedin a single section with leafs modifiedto pivot at the location of the currentcarrying cables and allow access to thecables and connected wiring. Electricalmodification is in the center of the hinge.
Product Number Example:83"MCK25HD CL x ACC-8*
*hinges are handed
ACCESSIBLE (ACC)
Product Number Example: 83"MCK25HD CL x -SER
Concealed Magnetic Monitoring (CM) is also available with the SER and ACC options.Product Numbering Example: MCK25HD-83C x CM-SER
MCK25HD-83C x CM-ACC
Flat cable connector is warranted for five years. Failure to install the 4 amp in-line fuse voids the warranty
ACC is the same leaf components witha single piece (full length) gear cap...and is accessible/non-removable.
SER Option Shown
McKINNEY Hinge CatalogMagnetic Monitoring Hinge (MM Option)
90 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
• Switch is U.L. Listed at 6V - .25 amps; 12V- .25 amps; 24V - .125 amps; 48V - .062 amps
• For low voltage (48 volt maximum) .25 AMP AC or DC non-inductive load
• Monitoring feature undetectable when hinge is installed
• Magnetic reed concealed switch imperviousto dirt and moisture
• 12" leads supplied as standard (extra lengths available)
• Narrow Stile (NS) Switch and Wide Gap Magnet options available
• Can be used in conjunction with QC option on most full mortise hinges up to QC12
• Can be used in conjunction with CC option on most full mortise hinges up to CC8 Wire
The McKINNEY Magnetic MonitoringHinge is the only system on the marketthat permits field replacement ofmagnet and switch. It is a simple,dependable system which defiesdetection, yet is readily accessible forinspection and easy adjustment.
MM Electric Hinges should beinstalled in the center position on doors with three hinges or the secondhinge position from the bottom ondoors with four hinges. Neither switchnor operating magnet are attached to
the hinge. Non-attachment featurereduces the chance of damage duringinstallation. Installation instructionspacked with each hinge.
All MM Electric Hinges areindividually factory pre-tested.
The MM feature is available onmost two, three and five knuckle fullmortise standard and heavy weighthinges, including the 1502 SpringHinge, and our full mortise aluminumcontinuous hinges. Consult theindividual catalog pages for this optionfeature.
MM Features:
REAR VIEW
U.L. Listing
6 V .25 Amps
12 V .25 Amps
24 V .125 Amps
48 V .062 Amps
UNDERWRITERSLABORATORYLISTED
APPLICATION
FRONT VIEW
McKINNEY Hinge CatalogJunction Box for Electric Hinges
91An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
20 gauge galvanized sheet steel, furnished in 2C finish.
MG-16
Recommended for use with our Concealed Circuit and Concealed Switch Hingesto protect wires. Unit to be installed in middle hinge location.
• Knock-out holes on both ends for wires to pass through
• Removable cover plate from end brackets• Guard supplied assembled for use with
electric hinges• Fits hinge reinforcements for 41⁄2" or 5"
contact grade hinges
Features:
McKINNEY Hinge CatalogFull Mortise Pocket Pivot Hinge
92 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Investment cast steel base materialpolished and plated or furnished inprime or powder coat finish.
The Full Mortise Pocket PivotHinge is designed to give a flushappearance to the corridor when thedoor is open and recessed into a pocketin the corridor wall.
For single and cross corridor doors,the PH-4 allows the door to lay againstthe wall with no projection into theopening and no gap between the doorand frame.
When combined with a floorcloser, this application has minimumvisible hardware and clearances.
The PH-4 Full Mortise PocketPivot Hinge meets material andperformance requirements of NFPA-80and ANSI A-156-1
PH-4
All Pocket Pivot Hinges are packedwith all machine and all wood screws.
• Two thrust bearings for vertical loads• Roller bearing for lateral support• Listed for both hollow metal or steel
covered composite fire doors rated up to 3 hours
• Listed for wood core type fire doors rated 20 minutes
• .187 Gauge• Non-handed
Features:
Recommended for applications where Swing Clear Hinges are aestheticallyunacceptable and use of the full width of the corridor is required, such as crosscorridor and smoke and fire doors as well as patient room doors.
Specifications# of HingesRequired Maximum Door WeightPer Door Door Size (lbs)
2 3'0" x 7'0" 150
3 3'0" x 7'0" 250
4 4'0" x 7'0" 350
Packing:Meets or exceedsANSI A117.1 - 1986Providing Accessibilityand Usability forPhysicallyHandicapped People
APPLICATION
C USLISTED
McKINNEY Hinge CatalogStandard WeightLoose Pin Hinges
93An ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
SpecificationsSize Size of
(Inches) Gauge Wood Screws
31⁄2 x 31⁄2 .123 7⁄8" x 9
4 x 4 .130 1 x 12
703 STEEL
• For use on doorways of very low frequencyand medium weight in industrial application
• Hinges are also available blank (withoutholes) for welding
• Available in plain steel with brass pins• Full mortise on both doors and jambs• Plain steel furnished less screws; zinc plated
hinges furnished with all wood screws
Features:
DISCONTINUED
McKINNEY Hinge CatalogFull Mortise Five Knuckle Plain BearingLight Weight Hinges
94 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Steel based material planished andplated or powder coated or bonderizedand primed for paint.
1400 - Square Corner1414 - 1⁄4" Radius1458 - 5⁄8" - 5⁄8" Radius
Available SizesInches MM Gauge
31⁄2 x 31⁄2 88.90 x 88.90 .099
4 x 4 101.60 x 101.60 .099
• Full mortise on both doors and jambs• Can be supplied as bulk pack, assembled
or unassembled• Supplied with all wood screws as standard• Machine screws available by special order
Features:
Recommended for use on light weight, low frequency doors hung in wood jambs inresidential construction.
1/4" Radius Shown
1400 / 1414 / 1458
Note: The plated finish on this non-contract grade hinge may not matchthat of an architectural grade hinge.
31⁄2" x 31⁄2" 4 x 4 Staggered HolePattern
McKINNEY Hinge CatalogOlive Knuckle Full MortiseStandard Weight Bearing Hinge
95An ASSA ABLOY Group company An ASSA ABLOY Group company Jun
e 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
• Designed for unusual decorative effect since only olive knuckle is visible whendoor closed
• Permanently attached anti-friction bearingcarries vertical load
• Non-removable stainless steel pin• Full mortise on hollow metal or wood doors
and frames• Handed hinge
Features:
Brass casting polished and/or plated.
TA3383
Recommended for use where doors are of average weight and average frequency,such as fine residential and commercial buildings such as offices, restaurants,hotels/motels or other public buildings where an architecturally pleasingappearance is desired.
SizeInches MM Gauge
6 152.40 .203
All TA3383 Olive Knuckle Hinges arepacked with all machine (1⁄2" x 12-24)and all wood screws (11⁄4" x 12).
Packing:APPLICATION
Discontinued
McKINNEY Hinge CatalogRaised Barrel Full MortiseStandard and Heavy Weight Hinges
96 An ASSA ABLOY Group company An ASSA ABLOY Group companySep
t 20
03
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Hinges for square edge doors suppliedwith no hole in bottom plug, side-viewMcKINNEY stencil and NRP featureare reversible for handing.
Hinges for beveled edge doors suppliedwith standard plug and are handed(specify RB-TA4714 or RB-TA4314standard weight or RB-T4A4786 orRB-T4A4386 for heavy weight).
All Raised Barrel Hinges are packedwith all machine x 1⁄2 wood screws.
Packing:
• Door leaf mortised into door• Frame leaf may be mortised or
surface applied• Non-removable stainless steel pin• Full mortise on hollow metal or wood doors
and frames• Handed hinge
Features:RB-TA2714 / RB-TA2314 RB-T4A3786 / RB-T4A3386
Standard weight recommended for use on average frequency and/or medium weight wood or metal doors in schools, hospitalsor other public buildings where medium traffic is experienced.
Heavy weight recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other publicbuildings where heavy traffic is experienced.
Specification Schedule
Standard Wt Heavy Wt
Size (Inches) 41⁄2" x 41⁄2" 41⁄2" x 41⁄2"
Size (MM) 114.30 x 114.30 114.30 x 114.30
Gauge .134 .180
SQUARE EDGE BEVELED EDGE
McKINNEY Hinge CatalogSlip-In Full Mortise Type I and Type IIStandard Weight Bearing Hinges
97An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y 20
04
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All Slip-In Hinges are packed with allmachine x 1⁄2 wood screws.
Packing:
• Non-removable stainless steel pin• Handed hinge• Both leaves specially swaged to provide
5⁄16" clearance when leaves are parallel
Features:
TA-TB2314 Slip-In Brass, Bronze or Stainless Steel. TA-TB2714 Slip-In Steel.
TYPE I TA-TB2314 / TA-TB2714 TYPE II TA-TB2314 / TA-TB2714
Recommended for use on average frequency and/or medium weight aluminumdoors with aluminum frames in schools, hospitals and other public buildings wheremedium traffic is experienced.
One leaf has standard punching andcountersinking and the other leaf isdrilled and tapped so it can be insertedthrough a slot in the door frame. Both leaves are specially swaged toprovide 3⁄16" clearance between leaveswhen parallel.
Both leaves are drilled and tapped sothey can be inserted through a slot inthe door and frame. Both leaves arespecially swaged to provide 5⁄16"clearance between the leaves when parallel.
TYPE 1 TYPE 2
Available SizesInches MM Gauge
4 x 4 101.60 x 101.60 .130
41⁄2 x 4 124.30 x 101.60 .134
41⁄2 x 41⁄2 124.30 x 124.30 .134
Type I Hinges Handed - Indicate Hand When Ordering
RH Shown, LH Opposite
McKINNEY Hinge CatalogFull Mortise Interim Hinges
98 An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
All Interim Hinges are packed with allmachine x 1⁄2 wood screws.
When ordering, specify which is thedoor leaf and which is the jamb leafdimension.
Packing:
• For new or retrofit installations where the door and frame are prepared for different sizehinge leaves
• Available in both standard (TA2714; TA2314) and heavy weight (T4A3786; T4A3386)
• Hinges are handed
Features:INTERIM HINGE
Specifications
Door Leaf Jamb Leaf
5" 41⁄2" trimmed to height*
41⁄2" 4" trimmed to height*
Specifications
Jamb Leaf Door Leaf
5" 41⁄2" trimmed to height*
41⁄2" 4" trimmed to height*
Recommended for installations where door and frame are prepped for two differentsize hinges.
*An equal amount is trimmed from the top and bottom of the leaf. For custom trimming, consultthe factory.
McKINNEY Hinge CatalogContinuous Geared Aluminum Hinge
CG-1An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07O
cto
ber
2006
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
07
1-800-346-7707www.mckinneyhinge.com
Performance testing has shown that1,250,000 cycles can be achieved usingour exclusive bonded 4 conductor flatcable which is capable of carrying 4 amps@ 24 volts with a 16 amp in rush currentfor 300 milliamps. The electrical prep isprovided with a 4 amp in-line fuse toprotect the cable from any overload orsurge in power. Installing the hingewithout the fuse will void the warranty(5 year warranty on electrified hinges).
The standard Concealed Current(Option QC) electrically modifiedhinges are supplied with Flat plugconnectors at each leaf, with 4, 8 or 12wires at each leaf and two 6" pigtails for use with ElectroLynx® doors andhardware supplied by other ASSA ABLOYcompanies. In addition, these hinges arepackaged with a 36" and a 72" wireharnesses with connector on one endand leads for hard wiring on opposite end.
Our new Serviceable, SER andAccessible, ACC versions (refer tocatalog page 89) come furnished withthe hardware noted above. The SERversion is supplied in three separatesections which allow for the door to beinstalled and the 8" electrical sectioncan be installed at a later time. TheACC version is supplied as a singlehinge with leafs modified to pivot at thelocation of the current carrying cables.This allows for access to cables andconnected wiring.
Power Transfer Cut OutsPT & EPT Preps are available. A prepform must accompany your order andindicate handing, dimension from top of hinge to PT location, etc.
PT for: Adams Rite, Securitron, Yale,Centurion, Dorma
EPT for: Von Duprin
Magnetic Monitoring Hinge(MM Suffix) is available alone or withthe CC option. Refer to catalog page 90 for additional information on ourMM function.
PRODUCT INFORMATION ELECTRICAL MODIFICATONS
Two full-height, paired and geared leavesmanufactured of extruded 6063-T6aluminum Alloy / temper with pinlessassembly that distribute load stressuniformly along the full length of thedoor and frame.
To reduce wear, the frame and door leafare independently machined and thenanodized. This allows the machinedaluminum surfaces that are in directcontact with the bearing to have asmoother, harder surface.
The continuous hinge acts asreinforcement for both door and frame.Special hinge reinforcements are notrequired. However door and framemanufacturers standard is acceptableand removal of hinge reinforcements inthe door and frame is not advised.
The patented chemical composition andinjection process used to produce ourbearings provides for a stronger moreaccurately formed bearing whicheliminates premature wear, guaranteesproper alignment, and requires fewerbearings to carry more weight. And theintermeshing gear segments in the hingenow provide 50% more bearing surface,which results in less wear.
The gear design ensures identicaloperation of each leaf. This allows forvery little effort required in openingheavy commercial grade doors.
These hinges are Guaranteed For TheLife of the Opening (Flat cableconductor or electrically modified hingesare guaranteed for five years). They aretested and certified by UL® (USA &CANADA) to standards UL10B,UL10C and UB7C.2 Part B & BS476(positive pressure) for up to a 3-hour (A-Label) Fire Listing for all 4'0" x 10'0"and 8'0" x 10'0” door and frameassemblies.
These hinges have been cycle testedusing a 150 lb. door and are nowcertified fully functional after 1.5 millioncycles. Per ANSI / BHMA StandardA156.26-2000, these hinges conform to:Grade 2-150 (150# Door @ 1,500,000 cycles)Grade 1-300 (300# Door @ 1,000,000 cycles)Grade 2-300 (300# Door @ 500,000 cycles)Grade 1-600 (600# Door @ 500,000 cycles)
Fire Rating3 hours- hollow metal doors*90 minutes- wood fire doors
FirePins™
are required only for 3 Hour (A Label)Assemblies see page B for additionalinformation
Mounting Hardware To preventwarping of the door along the hingejamb, screws are located along the fulllength of the hinge.
These hinges are ideal for use on centerhung lead lined door
CYCLE REQUIREMENTS
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
Heavier weight can be carried. Contactthe factory at 800-346-7707 forapplications and those not listed in theabove chart
C USLISTED
Classified and Listed to meet therequirements of Standards, UL10B,UL10C, UBC7-2, Part 1 & BS476POSITIVE PRESSURE
LISTEDDoor Hinges
McKINNEY Hinge CatalogContinuous Geared Aluminum Hinge
CG-2 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
OTHER AVAILABLE OPTIONS DRILL SIZE CHART
Options may require handing. Refer toindividual catalog pages for availability
DD Dutch Door PrepHT Hospital TipCustom length, indicate handing andlength in inches
FirePins™ Kit
1. Frame Portion all fasteners are 12-24 x 7/16" Type C, FH U/C threadforming screws• 20 Screws are required per each leaf• Wood Screws available on request
and should be specified on order
• 1/2 x 12-24 Torx Pin Head MachineScrews available on request
2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"• 4 Required per hinge• Shoulder Bolt 1/4-20 x 1" PCH• 4 Required per hinge• Pan Head Self Drilling # 12 x 3/4• 6 Required per hinge
HALF –SURFACE HINGES
EDGE HUNG HINGES
1. Fasteners are # 12-24 x 7/16" Type C,FH U/C thread-forming screws• 20 Screws are required per each leaf• Wood Screws available on request
and should be specified on order• 1/2 x 12-24 Torx Pin Head
Machine Screws available on request
FULL –SURFACE HINGES
1. Frame Portion all fasteners are 12-24 x 7/16" Type C, FH U/C threadforming screws• 12 Screws are required for frame leaf
–Wood Screws available on request.• 1/2 x 12-24 Torx Pin Head Machine
Screws available on request2. Door Portion
• Thru-Bolt 1/4-20 x 1-5/8"– 4 Required per hinge
• Shoulder Bolt 1/4-20 x 1" PCH– 4 Required per hinge
• Pan Head Self Drilling # 12 x 3/4– 6 Required per hinge
12HD, 14HD, 22HD, WTHD, 25HD, 28HD & 54HD
Material Thickness Drill Size
Aluminum .090 - .140 13
Metal 20 Gauge 17
Metal 16-18 Gauge 15
Metal 12-14 Gauge 13
Wood N/A 5/32"
58HD
1/4-20 Screws
Aluminum .090 - .140 7
Metal 12 – 16 Gauge 7
Metal 18 – 20 Gauge 9
CL Clear anodized aluminumBZ Dark anodized aluminumG Gold anodized aluminumBL Black anodized aluminumSN Brushed satin nickel anodized
aluminum
Consult the factory for availability ofcustom colors on complete hinges or gearcaps only.
FINISHES
HINGE INSTALLATION
The top of the hinge should be installedflush with the top of the door leaf
Installation instructions are packed witheach hinge.
6'8" 79" 20067'0" 83" 21087'2" 85" 21598'0" 95" 241310'0" 120" 3048
Available Sizes
Door Size Hinge Length Hinge Length MM
– 79", 83", 85" 95" and 120" lengths arestandard for nominal door heights. Thehinges may be ordered in custom lengths,specify handing and length in inches.
– These hinges may also be cut in thefield. If the hinge must be shortened, cutthe bottom only using a chop saw. Thiswill allow material chips to work outafter the installation. Although thehinge is typically not handed, it becomeshanded after cutting and the cut edgemust be installed at the bottom.
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-3An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07O
cto
ber
2006
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
07
McKINNEY Hinge CatalogContinuous Geared Aluminum Hinge
Security, Safety, Privacy, Ease of Maintenance• Eliminates alignment problems, such as door sag and binding. Our continuous
hinge distributes load stress uniformly along the full length of the door and frame.
• Our inter-meshing gear design, which provides 50% more bearing surface, ensuresless wear and identical operation of each leaf, therefore, very little effort isrequired to open heavy commercial grade doors
• Screws located along the full length of the hinge prevents warping of the dooralong the hinge jamb
• Our continuous hinge acts as reinforcement for both door and frame
• Anodizing is performed after completing all machining, thus allowing that allaluminum surfaces that are in direct contact with the bearing have a smoother,harder surface, thereby reducing wear
• With our geared construction and full length channel cap, the common gapbetween the door and frame is sealed thereby providing security against prying
• The closing of the gap also protects against pinching fingers in doors in publicareas, especially those where children are present
• Sightproof design of the continuous hinge provides privacy for lavatories,executive offices, file rooms etc.
• Superior hinge design and bearings eliminate premature wear, guarantee properalignment and require fewer bearings to carry more weight. This is why we canguarantee our hinge for the Life Of the Opening*
• Our QC, Serviceable and Accessible Options make connecting a Snap!
* Hinges with electrical modifications carry a five year warranty from date of shipment
Why Choose a McKINNEY Continuous Geared Aluminum Hinge?McKINNEY commercial grade hinges consist of two full-heights paired and geared leaves. Each geared leaf rotates evenly formtop to bottom riding on Delrin® -Teflon® bearings. The geared leaves and bearings are held together by a full-length channel cap.This assembly retains the smooth, clean lines of the door and frame while easily supporting heavy vertical loads.
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogAluminum Continuous Gear HingeClearance Dimensions
CG-4 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
The full-mortise units are designed mainly for new doors and frames, and are applied so as to conceal both leaves. In retrofitapplications, the door width must be reduced for proper clearance (See Figures 1, 2, 3 and 4 below for proper clearance).
The full-surface units are designed mainly for retrofit work, and are applied to the exposed surface of the door and frame (See Figures 1 & 2 below for proper clearance).
The half-surface units are designed mainly for retrofit applications. The door leaf is applied to the exposed surface of the door,and the frame leaf is applied to the concealed surface of the frame rabbet (See Figures 1 & 2 below for proper clearance).
* Allow extra clearance as required per astragal manufacturer
Full Mortise5/16"
Full Surface0 to 1/8"
Half Surface1/8"
ALL 1/8"
ALL 1/8"
Full Mortise5/16"
Full Surface0 to 1/8"
Half Surface1/8"
ALL 1/8"
ALL1/8" to3/16"
Full Mortise5/16"
Full Surface0 to 1/8"
Half Surface1/8"
Figure 1 – Typical Figure 2 – Typical
Full Mortise / Raised GearWide Throw (w/SquareEdge Door) 5/16"
Wide Throw (w/Beveled 3/8"Edge Door
Residential 1-3/4"Raised Gear w/Beveled Edge Door 11/32"Full Mortise Safety 9/16"(w/Square Edge Door)
Full Mortise Safety 5/8"(w/Beveled Edge Door)
ALL 1/8"
ALL 1/8"
Figure 3 – Typical
Full Mortise / Raised GearWide Throw (w/SquareEdge Door) 5/16"
Wide Throw (w/Beveled 3/8"Edge Door
Residential 1-3/4" 1/4"
Full Mortise Safety(w/Square Edge Door) 9/16"
Full Mortise Safety(w/Beveled Edge Door) 5/8"
Raised Gear 11/32" (w/Beveled Edge Door)
ALL 1/8"
Figure 4 – Typical
Full Mortise / Raised GearWide Throw (w/Square
5/16" Edge Door)
3/8" Wide Throw (w/BeveledEdge Door
1/4" Residential 1-3/4"
9/16" Full Mortise Safety(w/Square Edge Door)
5/8" Full Mortise Safety (w/Beveled Edge Door)
11/32" Raised Gear (w/Beveled Edge Door)
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-5An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogContinuous Aluminum HingeFire Ratings
All Hinges designated with these symbols on our catalog pages are tested and certified by Underwriters Laboratories Inc®
(U.S.A. & Canada) to standards UL10B, UL10C (negative pressure) and UBC7.2 Part 1, & BS476 (positive pressure) for up toa 3-Hour (A Label) Fire Listing for all 4'0" x 10'0" and 8'0" x 10'0" door and frame assemblies. Fire listing certifications applyto all approved hollow metal and wood door assemblies in drywall or masonry wall construction. Our Intumescent FirePins™ areonly required on 3-Hour (A Label) assemblies.
Template Screw Locations •
1,500,000 Cycle Test w/150# Door By U.L. Certified Independent La •
UL10B Listed (Negative Pressure), UBC 7.2 (Positive Pressure) •
UL C Listed (Canada) •
Rated 20 min WD x HM Drywall •
Rated 20 min HM x HM Drywall •
Rated 20 min WD x HM Masonry •
Rated 20 min HM x HM Masonry •
Rated 30 min WD x HM Drywall (Canada) •
Rated 30 min HM x HM Drywall (Canada) •
Rated 30 min WD x HM Masonry (Canada) •
Rated 30 min HM x HM Masonry (Canada) •
Rated 45 min WD x HM Drywall •
Rated 45 min HM x HM Drywall •
Rated 45 min WD x HM Masonry •
Rated 45 min HM x HM Masonry •
Rated 60 min WD x HM Drywall •
Rated 60 min HM x HM Drywall •
Rated 60 min WD x HM Masonry •
Rated 60 min HM x HM Masonry •
Rated 90 min WD x HM (16 ga) Drywall •
Rated 90 min WD x HM (16 ga) Masonry •
Rated 90 min WD x HM (18 ga) Drywall •
Rated 90 min WD x HM (18 ga) Masonry •
Rated 90 min HM (20 ga) x HM (18 ga) Drywall •
Rated 90 min HM (20 ga) x HM (18 ga) Masonry •
Rated 90 min HM (20 ga) x HM (16 ga) Drywall •
Rated 90 min HM (20 ga) x HM (16 ga) Masonry •
Rated 90 min HM (18 ga) x HM (18 ga) Drywall •
Rated 90 min HM (18 ga) x HM (18 ga) Masonry •
Rated 90 min HM (18 ga) x HM (16 ga) Drywall •
Rated 90 min HM (18 ga) x HM (16 ga) Masonry •
Rated 90 min HM (16 ga) x HM (16 ga) Drywall •
Rated 90 min HM (16 ga) x HM (16 ga) Masonry •
Rated 90 min HM (16 ga Vert. Stiff) x HM (16 ga) Drywall •
Rated 90 min HM (16 ga Vert. Stiff) x HM (16 ga) Masonry •
Rated 3 Hour HM x HM Masonry/Drywall
Retrofit Applications - Fire Rated •
Maximum Rated Opening Size - Pair 8'0" Wide x 10' high •
Cut to Size in Field •
Indicates FirePins™ Required
s ss s
s s
LISTEDDoor Hinges
CG-6 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogContinuous Geared Aluminum HingeFirePins™
FirePin™ Locations• The loctions illustrated below
indicate where holes should be drilledon the hinge edge of the door
• These locations are appropriate for allhinge models (edge hung, full-surface,and half sufrace)
FirePin™ Locations for Use With Fire Rated Assemblies• Although McKINNEY Continuous Geared Hinges carry UL Fire Ratings
unequaled in the industry, some applications may require the use of FirePins™.Please refer to the Fire Label Ratings Chart (page CG-5) for informationregarding their use.
• FirePin™ applications fall within the UL guidelines for retrofitting assemblies inthe field. Expensive shop modifications and door/frame reinforcements are notrequired.
• FirePins™ also add extra security to a door assembly.
r
LISTEDDoor Hinges
d
McKINNEY Hinge CatalogFull Mortise - Edge Hung Flush DoorContinuous Gear Hinge
CG-7An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harness withconnectors on one end and hard wiringon opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toinstall the fuse voids the warranty.
• Quick Connect – Passes constant flow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12
• Serviceable – Same as QC except hingesupplied in three sections with 8"electrically modified leaf.SER-4; SER-8; SER-12*
• Accessible – Same as QC exceptfurnished with a pivoting 8” section.ACC-4; ACC-8; ACC-12
• MM – Magnetic Monitoring
• PT - Power transfer Prep (cut out only)For Adams Rite, Securitron, Yale,Dorma & Centurion*
• EPT – Power transfer prep (cut outonly) For Von Duprin*
*PT or EPT Location Form mustaccompany your order
Refer to catalog Pages 88-90 additionalinformation on our electrical options.
Extruded 6063-T6 aluminumalloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-12HD SERIES
STANDARD APPLICATION
The MCK-12HD Series is designed foruse with doors that are standard 1-3/4"up to 2-1/4" thick.
–Designed for use on retrofitapplications and allows for adjustmentin order to properly align the lock edgeof the door to the frame.
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.
Mounting Hardware # 12-24 x 7/16"FHUC, Type C, thread-forming. 20required for each leaf. Wood screwsavailable on request only.
For Kawneer Tuffline Series, specifythe prefix “K”, for instance 83" KMCK-12HD –Designed for use with bi-foldapplications to keep the faces of thedoors flush.
Kawneer Tuffline Series Application
The McKINNEY MCK-12HD continuousgear hinges are recommended for newconstruction and renovations includingnew door and frame, new door withexisting frame or existing door with new frame.
These hinges are GUARANTEEDFOR THE LIFE OF THE OPENING
The flat cable conductor or electricallymodified hinges are guaranteed for five years.
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
OPTIONAL FEATURES
LISTEDDoor Hinges
McKINNEY Hinge CatalogFull Mortise - Edge Hung Inset DoorContinuous Gear Hinge
CG-8 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harness withconnectors on one end and hard wiringon opposite end. A 4 amp fuse issupplied to protect the cable Fromoverload or surge in power. Failure toinstall the fuse voids the warranty.
• Quick Connect – Passes constant flowof current between source of powerand actuated devices in the door QC-4; QC-8; QC-12
• Serviceable – Same as QC excepthinge supplied in three sections with8" electrically modified leaf.SER-4; SER-8; SER-12*
• Accessible – Same as QC exceptfurnished with a pivoting 8" section.ACC-4; ACC-8; ACC-12
• MM – Magnetic Monitoring
• PT – Power transfer Prep (cut out only)For Adams Rite, Securitron, Yale,Dorma & Centurion*
• EPT – Power transfer prep (cut outonly) For Von Duprin*
*PT or EPT Location Form mustaccompany your order
Refer to catalog Pages 88-90 additionalinformation on our electrical options.
Extruded 6063-T6 aluminum alloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-14HD SERIES
79", 83", 85", 95" and 120" lengthsare standard for nominal door heights.The MCK-14HD continuous gear hingemay be field-cut to exact door heightsand also may be ordered in customlengths. Consult the factory for minimumrequirements on custom sizes.
The MCK-14HD Series is designed foruse with doors which are the standard1-3/4" up to 2-1/4" thick.
Mounting HardwareStandard Fasteners are#12-24x7/16" FH U/C, thread forming.20 required for each leaf.
Wood screws are available upon request.
–Designed for use with hollow metalframes, where the inset conforms toS.D.I. specifications for aligning doorsand frames
–Designed for use on retrofitapplications and allows for adjustmentsin order to properly align the lock edgeof the door to the frame.
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.
The flat cable conductor or electrically modified hinges are guaranteed for five years.
OPTIONS
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
SHORT LEAF INSET APPLICATION
LISTEDDoor Hinges
McKINNEY Hinge CatalogFull SurfaceContinuous Gear Hinge
CG-9An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
G – Gold Anodized FinishBL – Black Anodized FinishFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)
All electrically modified hinges arefurnished with our 4 conductor flatcable connectors at each leaf and pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harnesswith connectors on one end and hardwiring on opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toInstall the fuse voids the warranty
• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in the doorQC-4; QC-8; QC-12
• MM – Magnetic Monitoring
Refer to catalog Pages 88-90 additionalinformation on our electrical options.
Please note that Power Transfer Cut OutsPT & EPT are not available on this hinge.
Extruded 6063-T6 aluminum alloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-22HD SERIES
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.
The McKINNEY MCK-22HDcontinuous gear hinges are designedmainly for retrofit applications wherethe door must swing completely out ofthe frame opening. This hinge isapplied to the exposed surface of thedoor and frame.
It may also be used for newconstruction including new door andframe, new door with existing frame,existing door with new frame orexisting door with existing frame.
Mounting Hardware1. Frame Portion all fasteners are
12-24 x 7/16" Type C, FH U/Cthread forming screws• 12 Screws are required for frame leaf–Wood screws are available on request• 1/2x12-24 Torx Pin Head Machine
Screws available on request
2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"• 4 Required per hinge• Shoulder Bolt 1/4-20 x 1” PCH• 4 Required per hinge• Pan Head Self Drilling # 12 x 3/4
6 Required per hinge
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
FULL SURFACE SWING CLEAR APPLICATION
OPTIONS
LISTEDDoor Hinges
McKINNEY Hinge CatalogFull Mortise - Edge HungContinuous Gear Hinge
CG-10 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
Extruded 6063-T6 aluminumalloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-25HD SERIES OPTIONS
G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harnesswith connectors on one end and hardwiring on opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toinstall the fuse voids the warranty
• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in the doorQC-4; QC-8; QC-12
• Serviceable – Same as QC excepthinge supplied in three sections with8" electrically modified leaf.SER-4; SER-8; SER-12*
• Accessible – Same as QC exceptfurnished with a pivoting 8" section.ACC-4; ACC-8; ACC-12
• MM – Magnetic Monitoring
• PT – Power transfer Prep (cut outonly) For Adams Rite, Securitron,Yale, Dorma & Centurion*
• EPT – Power transfer prep (cut outonly) For Von Duprin*
*PT or EPT Location Form mustaccompany your order
Refer to catalog Pages 88-90 additionalinformation on our electrical options.
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.
The McKINNEY MCK-25HDcontinuous gear hinges are recommendedfor new construction and retrofitinstallations including new door andframe, new door with existing frame or existing door with new frame.
Mounting HardwareFrame Portion all fasteners are 12-24 x 7/16" Type C, FH U/C threadforming screws• 20 Screws are required for each leaf–Wood screws are available on request• 1/2x12-24 Torx Pin Head Machine
Screws available on request
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
SHORT LEAF FLUSH APPLICATION
LISTEDDoor Hinges
McKINNEY Hinge CatalogFull Mortise - Raised GearContinuous Gear Hinge
CG-11An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
Extruded 6063-T6 aluminumalloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-28HD SERIES OPTIONS
G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
– Designed for use on metal or woodframes with applied casing.
– Applied as to conceal both leaves
– Designed for use on metal or woodframes with applied casing
– Full mortise hinges are designed foraluminum door and frameapplications where the hinge leaf mayinterfere with the weatherstrip orapplied stop of the frame.
Mounting HardwareMCK-28HD Continuous Gear hingesare recommended for new constructionand retrofit installations including newdoor and frame; new door and existingframe, existing door and new frame
Fasteners are # 12-24 x 7/16" Type C,FH U/C thread-forming screws
1. 20 Screws are required per each leaf
2. Wood Screws available on requestand should be specified on order
3. 1/2x12-24 Torx Pin Head MachineScrews available on request
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
Door Closed
Door Open 90°
LISTEDDoor Hinges
5/16" @ Square Edge Application
11/32" @ Beveled Edge Application
McKINNEY Hinge CatalogHalf SurfaceContinuous Hinge
CG-12 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
Extruded 6063-T6 aluminumalloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-54HD SERIES OPTIONS
G – Gold Anodized FinishBL – Black Anodized FinishFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)All electrically modified hinges areare furnished with our 4 conductor flatcable connectors at each leaf and twopigtails for use with ElectroLynxconnectors as well as a 36" and a 72"wire harness with connectors on oneend and hard wiring on opposite end.A 4 amp fuse is supplied to protect thecable From overload or surge in power.Failure to Install the fuse voids thewarranty.
• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12
• PT – ower transfer Prep (cut outonly) for Adams Rite, Securitron,Yale, Dorma & Centurion*
• EPT – Power transfer prep (cut outonly) for Von Duprin*
*PT or EPT Location form mustaccompany your order.
Refer to catalog Pages 88-90 foradditional information on our electricaloptions.
The MCK-54HD series hinge isdesigned for use with hollow metalframes, where the inset conforms toS.D.I. specifications for aligning doorsand frames
–Designed for use on retrofit applicationsand allows for adjustment in order toproperly align the lock edge of the doorto the frame.
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.
The McKINNEY MCK-54HDcontinuous gear hinges are designedmainly for retrofit applications. Thedoor leaf is applied to the exposedsurface of the door and the frame leaf isapplied to the concealed surface of theframe rabbit. It may also be used fornew construction including new doorand frame, new door with existingframe, existing door with new frame orexisting door with existing frame.
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
HALF-SURFACE APPLICATION
MOUNTING HARDWARE
1. Frame Portion all fasteners are 12-24 x 7/16" Type C, FH U/C threadforming screws• 20 Screws are required per each leaf
• Wood Screws available on requestand should be specified on order
• 1/2x12-24 Torx Pin Head MachineScrews available on request
2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"
• 4 Required per hinge
• Shoulder Bolt 1/4-20 x 1" PCH
• 4 Required per hinge
• Pan Head Self Drilling # 12 x 3/4
• 6 Required per hinge
LISTEDDoor Hinges
McKINNEY Hinge CatalogFull SurfaceCenter Pivot Continuous Hinge
CG-13An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
Extruded 6063-T6 aluminumalloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-58HD SERIES OPTIONS
G – Gold Anodized FinishBL – Black Anodized FinishFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)All electrically modified hinges are arefurnished with our 4 conductor flat cable connectors at each leaf andtwo pigtails for use with ElectroLynxconnectors as well as a 36" and a 72"wire harness with connectors on oneend and hard wiring on opposite end. A 4 amp fuse is supplied to protect thecable from overload or surge in power.Failure to install the fuse voids thewarranty.
• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12
Please note that Power Transfer Cut OutsPT & EPT are not available on this hinge
The MCK-58HD Series is designed foruse where pivot point must be centeredbetween the door and frame and areapplied to the exposed surface of thedoor and frame.
–Designed for use where frame face isless than 1-1/2" wide.
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.
The McKINNEY MCK-58HDcontinuous gear hinges are designed forretrofit work and can be used for newconstruction and renovation projectsapplications where the pivot point mustbe centered between the door andframe, or where the frame face is lessthan 1-1/2".
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
HALF-SURFACE APPLICATION
MOUNTING HARDWARE
1. Frame Portion all fasteners are 12-24 x 7/16" Type C, FH U/C threadforming screws• 12 Screws are required for frame leaf
• and should be specified on order
• 1/2x12-24 Torx Pin Head MachineScrews available on request
2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"
• 8 Required per hinge
• Shoulder Bolt 1/4-20 x 1" PCH
• 8 Required per hinge
• Pan Head Self Drilling # 12 x 3/4
• 4 Required per hinge
LISTEDDoor Hinges
McKINNEY Hinge CatalogWide Throw Full-MortiseContinuous Gear Hinge
CG-14 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
Extruded 6063-T6 aluminum Alloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-WTHD SERIES OPTIONS
G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
Electrical Modifications (Suffix)All electrically modified hinges are arefurnished with our 4 conductor flatcable connectors at each leaf and twopigtails for use with ElectroLynxconnectors as well as a 36" and a 72"wire harness with connectors on oneend and hard wiring on opposite end. A4 amp fuse is supplied to protect thecable from overload or surge in power.Failure to install the fuse voids thewarranty
• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12
• Serviceable – Same as QC excepthinge supplied in three sections with8" electrically modified leaf.SER-4; SER-8; SER-12*
• Accessible – Same as QC exceptfurnished with a pivoting 8" section.ACC-4; ACC-8; ACC-12
• MM – Magnetic Monitoring
• PT – Power transfer Prep (cut outonly) For Adams Rite, Securitron,Yale, Dorma & Centurion*
• EPT – Power transfer prep (cut outonly) For Von Duprin*
*PT or EPT Location Form mustaccompany your order
Refer to catalog Pages 88-90 additionalinformation on our electrical options.
Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.Undersizing of door must also includeclearances for lock side of door, added toclearance, to obtain the properUndersizing of door.The McKINNEY MCK-WTHDcontinuous gear hinge is recommendedfor new construction or renovationsthat require extra clearance due tospecial frame or door design and areapplied so as to conceal both leaves.These include new door and frame, newdoor with existing frame or existingdoor with new frame, or new doorapplications that require extra clearance(provides 2-3/4" clearance) due tospecial frame or door design.
Requires 5/16" clearance for square edgedoors and 3/8" clearance on beveled edge doors. Clearances noted here are forhinge edges only. Undersizing of doormust also include clearance for lock sideof door, added to hinge clearance toobtain proper undersizing of door.
Mounting Hardware1. Fasteners are # 12-24 x 7/16” Type C,
FH U/C thread-forming screws1. 20 Screws are required per each leaf2. Wood Screws available on request and
should be specified on order3. 1/2x12-24 Torx Pin Head Machine
Screws available on request
APPLICATION
7'0" 83" 21088'0" 95" 2413
Available Sizes
Door Size Hinge Length Hinge Length MM
LISTEDDoor Hinges
McKINNEY Hinge CatalogFull Mortise - Safety HingesContinuous Gear Hinge
CG-15An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
Extruded 6063-T6 aluminumalloy/temper with pinless assembly.
CL – Clear anodized aluminumBZ – Dark anodized aluminum
MCK-35HD & MCK-38HD SERIES OPTIONS
G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)
1. Fasteners are # 12-24 x 7/16" Type C,FH U/C thread-forming screws
1. 20 Screws are required per each leaf
2. Wood Screws available on requestand should be specified on order
3. 1/2x12-24 Torx Pin Head MachineScrews available on request
–Designed mainly for new doorapplications in child care and nursingfacilities. These hinges require extraclearance with a special frame designand are applied as to conceal bothleaves.
–The unique design prevents smallfingers from getting pinched in the door.
–Safety hinges are designed for frameswith no stops on the hinge jamb
Door Hinge # of DoorSize Length Bearings Weight
6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs
MCK-35HD
Required 13/16" clearance for squareedge doors and 27/32" clearance onbeveled edge doors.
MCK-38HD
Required 13/16" clearance for squareedge doors and 27/32" clearance onbeveled edge doors.
LISTEDDoor Hinges
LISTEDDoor Hinges
McKINNEY Hinge CatalogStainless and Steel Continuous HingesStainless Edge Guards
CG-17An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
PRODUCT INFORMATION
Our Pin and Barrel Hinge stainless steel, 300 and 3500 Seriesand cold rolled steel 3700 Series are UL listed.
Our stainless and steel continuous hinges distribute shockforces evenly so wear and tear to the frame and door isreduced significantly. Security is enhanced by preventinginsertion of devices between the door and frame thus reducingvandalism. The continuous design allows for easy alignmentof electrical transfers and monitoring switches. These hingesalso aid in stopping air infiltration by creating a complete sealfrom top to bottom of the door at the hinge stile.
The Pin and Barrel Hinge is held together with a 1/4" stainlesssteel Teflon coated rod free moving rod. The hinge works ona split bearing assembly which eliminates premature wear andguarantees proper alignment.
The Pin and Barrel Hinge acts as reinforcement for both doorand frame. For the majority of our hinges, special hingereinforcements are not required. However door and framemanufacturers standard is acceptable and removal of hingereinforcements in the door and frame is not advised. Whenusing our HG models HG-305, HG-310, HG-322, HG-326and HG3505 in a hollow metal door application, we stronglysuggest reinforcement at the lock side of the door for properuse of the AdjustaScrews™ assembly. This addedreinforcement will ensure the proper amount of material forthreading the Adjusta-Screw, giving the assembly the strengthneeded to last the life of the opening. It is important to notethat these added reinforcements must be added to the door at time of manufacture. Please be sure to take this intoconsideration when ordering your doors. Again, thisreinforcement applies only to the Adjusta-Screw assembly and is not needed for any other hardware application.
Door Hinge Length Weight CapacitySize 1-3/4" Doors
Inches MM 300 & 3700 Series6'8" 78.75" 2000.2 600 lbs7'0" 83.125" 2111.4 600 lbs7'2" 85" 2159.0 600 lbs8'0" 95" 2413.0 600 lbs10'0" 118.75" 3016.2 600 lbs
Door Hinge Length Weight CapacitySize 2" Doors
Inches MM 3500 Series6'8" 78.75" 2000.2 900 lbs7'0" 83.125" 2111.4 900 lbs7'2" 85" 2159.0 900 lbs8'0" 95" 2413.0 900 lbs10'0" 118.75" 3016.2 900 lbs
CYCLE REQUIREMENTS
Both the 300 Series and 3500 Series stainless hinges meet or exceed ANSI / BHMA Standard A156.1 - Grade 1.The 3700 Series steel hinge meets or exceeds ANSI / BHMAStandard A156.1 – Grade 2.
Classified and Listed to meet the requirements ofStandards, UL10B, UL10C, UBC7-2 POSITIVE PRESSURE
Maximum Door Opening:
– Single Doors: 4'0" x 10'0"– Pair of Doors: 8'0" x 10'0"
Fire Rating3 hours
– hollow metal doors mounted singly
90 minutes– hollow metal and composite core wood fire doors
20 minutes– wood doors
MOUNTING HARDWARE
To prevent warping of the door along the hinge jamb, screwsare located along the full length of the hinge. The templatedhole pattern makes these hinges are ideal for use on center-hung lead lined doors – Lead Line covers are available forsurface mount units.
Our AdjustaScrews™ fastener available on the Hinge Guardmodels permits up to 3/8” width adjustment. Full door lengthadjustment can means doors can be squared accurately andeasily in new installations and existing frames can be used inretrofits. Future adjustments can be made by the Maintenancestaff by re-positioning the Adjusta-Screw fasteners.
Please refer to the individual catalog pages for fastenerinformation.
Hinges may be field cut per installation instructions.
FINISHES
The 300 and 3500 Series stainless hinges are supplied as astandard in brushed satin finish US-32D (630) and areavailable in brite stainless US-32 (629). The 3700 series steelhinges are supplied in Gray Powder Coat finish. Consult thefactory for availability of custom finishes.
McKINNEY Hinge CatalogStainless and Steel Continuous HingesStainless Edge Guards
CG-18 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
HINGE NUMBERING SYSTEM
EG – Edge GuardFM – Edge MountFS – Full SurfaceHG – Hinge/GuardHM – Half MortiseHS – Half SurfaceSC – Swing Clear
This series number indicates the type of hinge and basematerial used:
Hinge Series300 14 Gauge, 304 Stainless steel barrel hinges with
stainless pin
3500 12 Gauge, 304 stainless steel pin and barrel securityhinges with stainless pin
3700 14 Gauge, 1012 Carbon steel barrel hinges withstainless pin
Hinge ModelsThe last two digits of the model number indicate theapplication:
00 – edge mount (formerly full mortise)01 – full surface, 1/8" offset02 – full surface, flush03 – half surface, 1/8" offset04 – half mortise, 1/8" offset05 – edge mount hinge/guard06 – half mortise hinge/guard07 – double hinge/guard08 – edge guard09 – full surface, swing clear10 – swing clear hinge/guard11 – edge mount, self aligningOther numbers are used for specific applications
Option SuffixesAMS – Adjustable Monitoring SwitchCC – Concealed Current TransferDD – Dutch DoorPT – Power Transfer Cut Out for Adams Rite, Securitron,Yale, Centurion & DormaEPT – Power Transfer Cut Out for Von DuprinES – Exposed Monitoring SwitchHT – Hospital TipLL – Lead LinedMB – Medical BearingsPC – Powder CoatedRB – Raised BarrelWT – Wide Throw
HANDING
Some Options including but not limited to CC, PT, EPT, HT,will require handing. Refer to the individual catalog pages.
Specify handing on all custom hinge lengths.
Custom Design
McKinney’s engineering department will be willing to assistyou in developing custom applications to solve any of yourunique door hinging problems. Together with the customer,we will go through an official sign-off process to assure customhinges fit your exact needs.
Medical Bearings for 300 series Hinges
Specially designed for hospitals and other high frequencyopenings.
Patented fiber-reinforcement polymer bearings:– Self lubricating with high resistance to wear– Uniquely designed to provide clean and quiet hinge
operation– Exceeds ANSI/BHMA Grade 7 requirements– Support doors weighing up to 600 lbs.– 25 year warranty
Specify by suffixing “MB” to the Stainless steel hinge models
McKINNEY Hinge CatalogStainless and Steel Continuous HingesStainless Edge Guards
CG-19An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
HINGE MODIFICATOINS
Hospital Tip
Available on all models except spring-loaded toilet partition hinges,
FS 321 and FM 327.Suffix hinge “-HT”Helps provide a safe, clean environment
Dutch Door Prep
Available on all hinge modelsSuffix hinge “-DD”Continuous frame leaf with two-piece
door leafIndicate handing, clearances, door and frame heights, and materials when
ordering
Wide Throw
Only available on 300 series hingesSuffix hinge “-WT”Specify distance from pin centerline to
heel edge of hinge when ordering
Reinforcement may be required on extreme wide throw applications.
These conditions will be determinedthrough a drawing approval process.
Cost will be determined at time of approval
BlankHoles omitted for specialapplications, such as welded installation.Not available on adjustable models.
Standard Edge Guard Cut-Outs
• 4 7/8 ASA strike • manual flush bolt• 161 latch • automatic flush bolt• 86 mortise • 161 strike
Security Studs
Stainless steel security studs mounted to the frame leaf
Door leaf is drilled to accommodate studsThree studs installed on hinges up to 7'2"Four studs installed on hinges over 7'2"Door and frame must be specially prepared to accommodate security studs
Sheared Leaf
Used for narrow door thickness’, unevenlyrabbetted frames or other special
applicationsSpecify distance from pin centerline to
heel edge of hinge when ordering
Custom Hole PatternAny hole shape or pattern other thanMcKinney's standard templated hole
patternIndicate desired pattern and include
dimensioned diagrams when ordering
Raised Barrel (Swaged)Available on all edge mount and half
surface models except on Aluminum hinges
Required on models FS-201, FS-202,FS-301 & FS-302 in order to open 180°Suffix hinge “-RB”For cased open or center pivot doors
McKinney Hinge CatalogStainless and Steel Continuous HingesStainless Edge Guards
CG-20 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
HINGE MODIFICATOINS
AMS Adjustable Monitoring Switch
Rigid welded assembly gives you the ability to adjust your monitoring switch to work with all applications.
Not available on aluminum hinges or powder coat finishes.
CC Concealed Current Transfer
For 300, 3500, and 200 series Edge mount only. Not available on Raised Barrel applications.
CE-4: Qty (4) 28ga wiresCE-8: Qty (8) 28ga wires
Handing required
CT Current Transfer Contact Switch
Rated for 16 amp. surge currentNo wire furnished: 1/4-20 screw posts will accommodate any gauge wire
Recommended only for low-traffic doors;requires CTP Current Transfer Prep
MP-ETAPElectrical Transfer Access Prep
Modifications that allows easy one person access to wiring between thehinge and door/frame.
PT or EPT Current Transfer Prep
Hinge leaf cutout to accommodate PT for Adams Rite, Securitron, Yale, Centurion & Dorma
EPT for Von DuprinPlease provide location and handing for all locations.
Standard Edge Guard Cut-Outs
• 4 7/8 ASA strike • manual flush bolt• 161 latch • automatic flush bolt• 86 mortise • 161 strikeEdge Guard Order Form must accompany your order
Security Fastener
Torx Head security fastenersare available in lieu of standard fasteners.
Standard Powder Coat Finishes
MP-PC-1 Dark Bronze
MP-PC-2 Eggshell White
MP-PC-3 Semi Gloss Black
MP-PC-4 Aluminum
MP-PC-5 Sun Gold
MP-PC-6 Light Copper
MP-PC-7 Polished Brass*
* FM300 Series only
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-21An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
ADJUSTA-SCREW ASSEMBLY
One full turn of the ajusta-screw adjusts thewidth of the door and hinge assembly 1/16"
The door width can be adjusted up to .3/8"with the Adujsta-Screw assembly as shown
MP-7 10-32 x 3/4"Phillips flat head
undercut stainless steelmachine screw
MP-25 13/8"Adjusta-stud fastener
with 10-32 internal threadand hex head adjustment
NOTE:You must predrill your door using a 5/16"bit for every fastener.Please see instruction sheets for full details on proper prepwork and installation procedures.
Adjust screw assemblies are also approved onour Edge Guards, EG-308 and EG-T308.The Underwriters Laboratories Inc.certification file number is R15384(N)
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-22 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
ADJUSTA-STUD HOLLOW METAL VS WOOD
The right hand Adjusta-Stud was designed for use in a wood door application. The Adjusta-Stud will cut its own thread intothe pre-drilled pilot hole. Pre-tapping of the pilot hole is not required in a wood application.
HG-3505, HG-305, HG-310, HG-322, HG-326
MP-7 10-32 x 3/4"Phillips flat head
undercut stainless steelmachine screw
MP-25 13/8"Adjusta-stud fastener
with 10-32 internal threadand hex head adjustment
NOTE:When ordering the hinges indicated above, where the Adjusta-Stud is included at no extra charge, you must indicate whichtype of application is preferred. The standard default will provide the right hand Adjusta-Stud.
The left hand Adjusta-Stud was designed for use in a hollow metal door application. Proper reinforcement must first be appliedto the door during manufacturing to allow for tapping of the 3/8-16 left handed thread. Using this left handed stud in a hollowmetal door application will help prevent the stud from dropping into the door during hinge installation and adjustment.
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-23An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
MCK-FM300 EDGE MOUNT OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths- specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix, may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel• WT Wide Throw
Electrical Modifications (Suffix)• AMS Adjustable Monitoring Switch• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out
Only) For Adams Rite, Securitron,Yale, Dorma & Centurion*
• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *
Consult the Factory on other availableoptions
* Power Transfer Location Templatemust accompany your order
When installed on a 16 gage (orheavier) metal frame, hinge reinforce-ments are not required, nor are theyrecommended. However, if the framesare equipped with mortise hingereinforcements, removal is not advised.
This edge-mounted pin & barrel typehinge is used on many of today’s hightraffic, high abuse doors. The hingeworks well in locations that usedanchor hinges, pivot reinforcementhinges or thrust pivot unit and hingesets. This hinge saves on special doorand frame preparation charges andmakes the installer’s job easier. It can be used on both fire labeled and non-labeled openings.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.0
8'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
A156.26 Grade 1
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners when closedFastener screw pack includes#10x7/8" PH U/C Self Drilling, 410 S.S.#10x1-1/4" PH U/C S.S.
Capacity (1-3/4” Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter, 304 stainless steel pinLong-life split nylon bearingsExterior barrel diameter .438 (7/16)
Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-24Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogFull Surface, 1/8" InsetStainless Steel Continuous Hinge
An ASSA ABLOY Group company
MCK-FS301 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Brite dipped fastener cover• 1-3/4" aluminum sleeve bolts
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised Barrel• LL Lead-lined cover w/ 1/16"
lead-lining
Consult the Factory on other availableoptions
When installed on a 16 gage (orheavier) metal frame, hingereinforcements are not required, nor arethey recommended. However, if theframes are equipped with mortise hingereinforcements, removal is not advised.
For 1/8" inset doors. This surfacemounted hinge can be used to repairboth fire labeled and non-labeled doorsthat have very tight clearances. Thehinge has a built-in 1/8" offset to assistin weather seal and sound barrier areas.
78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed Universal screw pack includes 1/4-20 x 3/4 PPH Tek SD, Zinc #8 x 3/4”PHF Tek, Zinc Cover Clip
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-25 Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogFull Surface Flush MountStainless Steel Continuous Hinge
An ASSA ABLOY Group company
MCK-FS302 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Brite dipped fastener cover• 1-3/4" aluminum sleeve bolts
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised Barrel• LL Lead-lined cover w/ 1/16"
lead-lining
Consult the Factory on other availableoptions
When installed on a 16 gage (orheavier) metal frame, hingereinforcements are not required, nor arethey recommended. However, if theframes are equipped with mortise hingereinforcements, removal is not advised.
For flush doors. This surface mountedhinge can be used to repair both firelabeled and non-labeled doors thathave very tight clearances, giving it aweather tight seal.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting Hardware (1-3/4" Doors)No exposed mounting fasteners whenclosed Universal screw pack includes 1/4-20 x 3/4 PPH Tek SD, Zinc #8 x 3/4”PHF Tek, Zinc Cover Clip
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-26Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogHalf SurfaceStainless Steel Continuous Hinge
An ASSA ABLOY Group company An ASSA ABLOY Group company
MCK-HS303 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised Barrel• LL Lead-lined cover w/ 1/16"
lead-lining
Electrical Modifications (Suffix requireshanding)
• PT Power Transfer Prep (Cut out forframe leaf only) For Adams Rite,Securitron, Yale, Dorma & Centurion*
• EPT Power Transfer Prep (Cut out forframe leaf for frame leaf only) For VonDuprin*
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This half-surface pin & barrel typecontinuous hinge can be used to repairboth fire labeled and non-labeledopenings. The hinge fits into the gapleft after standard butt hinges areremoved. It can assist in reversing thehanding of a door, or to reverse theswing of a door hung in an evenly-rabbetted frame. (Please call the factoryat 800-346-7707. for instructions onunevenly-rabbetted frames.)
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.0
10'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S. Cover Clip #8 x 3/4" PHF Tek, Zinc
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-27An ASSA ABLOY Group company An ASSA ABLOY Group company Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
2007
1-800-346-7707www.mckinneyhinge.com
MCK-HM304 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom lengths - specify in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised Barrel
Electrical Modifications (Suffix requireshanding)• PT Power Transfer Prep (Cut out door
leaf only)For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer Prep (Cut out doorleaf only) For Von Duprin *
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This pin & barrel type hinge is used torepair wooden doors that have split, orare chipped and dented from trafficabuse. The surface mounted frame leafallows for easy retrofit installation. This hinge can be used to reverse thehanding or swing of the door withoutany modifications to the existing door.
MCK-HM304
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S. 1/4-20 x 1-3/4" Sleeve Bolt SSCover Clip #8 x 3/4" PHF Tek, Zinc
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
MCK-HM304
Heavy-Duty 14 Gauge 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
MCK-HM304
Classified in accordance with UBCcode standard 7-2 for positivepressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-28 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogEdge Mount, Full-Wrap Edge GuardStainless Steel Continuous Hinge
MCK-HG305 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised Barrel
Electrical Modifications (Suffix requires handing)• AMS Adjustable Monitoring Switch
• CC4 Concealed Circuit (4 Wire)
• CC8 Concealed Circuit (8 Wire)
• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer Prep (Cut out Only)For Von Duprin *
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAsssembly. This added reinforcement willensure the proper amount of material forthreading the Adjusta-Screw, giving theassembly the strength needed to last thelife of the door. Remember to order yourdoors with reinforcement.
This unique design answers the problemof adjusting doors where frames are notinstalled plumb or properly aligned. Notonly that, but the wrap-around edgeguard protects the door from unsightlydents and gouges and will deflectobjects, preventing further damage.Strategically located fasteners coupledwith the AdjustaScrew fastener allowthe door to be adjusted up to 3/8"within the channel of the hinge anddistribute the load of the door down theentire length of the jamb. The properalignment of the door to the frame willallow your closers, panics magneticlocks, electronic strikes, and automaticoperators to assist you in meeting allyour life safety code requirements.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.
#10 x 1-1/4" PH U/C S.S.
10-32 x 3/4" PH U/C S. S.
1-3/8" RH, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge 304 stainless steelFinished in 32D (630)
Door Closed
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
Door Open 90°
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-29An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogHinge GuardStainless Steel Continuous Hinge
MCK-HG306 OPTIONAL FEATURES
• 32 Bright Polished• Custom lengths - specify length in inches• Custom hole pattern• Tamper-proof security• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised Barrel
Electrical Modifications (Suffix requires handing)
• PT Power Transfer Prep (Cut out doorleaf only) For Adams Rite, Securitron,Yale, Dorma & Centurion *
• EPT Power Transfer Prep (Cut out doorleaf only) For Von Duprin *
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gauge (or heavier)metal frame, hinge reinforcements are not required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This barrel-type hinge is used withhollow metal frames and wood orhollow metal doors. The guard thatwraps the door covers up dents,scratches, and splitting of the door.This product covers the door’s edge andwraps the door face to prevent furtherdamage. This hinge can also be used toreverse the swing of a door.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.Cover Clip#8 x3 /4" PHF Tek, Zinc
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-30 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogFull Surface, Swing ClearStainless Steel Continuous Hinge
MCK-FS309 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Brite dipped fastener cover• 1-3/4” aluminum sleeve bolts
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• LL Lead-lined cover w/ 1/16"
lead-lining
Consult the Factory on other available options
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This barrel-type hinge is used to ensurethat a door opened to a 90-degree angleis removed from the opening. Thishinge will mount on a 1 3/4" face, andis especially useful for ADA upgradework and lead lined door conversionprojects.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross ReferenceMounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes#10 x 1-1/4" PH U/C S.S.#10 x 7/8" PFH U/C SD, 410 SS1/4-20 x 3/4 PPH Tek SD, Zinc#8 x 3/4" PHF Tek, ZincCover Clip
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-31An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogEdge Mount, Half-Wrap Edge GuardStainless Steel Continuous Hinge
MCK-HG310 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel
ToolsMTSP-100 Right angle skew driver forease of installation
Consult the Factory on other available options
When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAsssembly. This added reinforcement willensure the proper amount of material forthreading the Adjusta-Screw, giving theassembly the strength needed to last thelife of the door. Remember to order yourdoors with reinforcement.
ADA-compliant barrel-type hinge isused on operating room doors to swingthe door out of the opening whenmoving equipment in and out. Thehinge guard also protects the door fromdents and gouges.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.10-32 x 3/4" PH U/C S. S.1-3/8" H, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter .438 (7/16)
Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-32 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogSwing Clear, Half-Wrap Edge GuardStainless Steel Continuous Hinge
MCK-HG311 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel
Tools
MTSP-100 Right angle skew driver forease of installation
Consult the Factory on available options
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
ADA Compliance
This surface applied swing clear versionallows doors to meet ADA requirements.The single wrap protects door edgesfrom cart damage.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosedFastener pack includes#10 x 7/8 PHF U/C SD 410 SS#10 x 1-1/4" PHF U/C SS
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-33An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogEdge Mount, Half-Wrap Edge GuardStainless Steel Continuous Hinge
MCK-HG315 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrelElectrical Modifications (Suffix requireshanding)
• AMS Adjustable Monitoring Switch• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *
Consult the Factory on other availableoptions
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
Featuring our unique edge guard, thiseconomical hinge prevents objectsbeing placed between the door andframe as well as protecting the door’sedge while supporting the door’s weightalong the entire length of the jamb.The EG-C308 Edge Guard when usedwith this hinge makes for a nicelybalanced look.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PFH U/C SD 410 SS#10 x 1-1/4" PFH U/C SS
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-34 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogFull Surface, 3/4" InsetStainless Steel Continuous Hinge
MCK-FS321 OPTIONAL FEATURES
• DD Dutch door hinges (DD Form
• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• LL Lead lined cover with 1/16" lead
lining
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This surface mount pin & barrel modelwas developed to work in conjunctionwith existing 3/4" offset floor closers.Where top or intermediate pivots haveworn and the floor closer will remain,the FS-321 is the solution to extendingthe life of the opening.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes 1/4-20 x 3/4 PPH Tek SD Zinc#8 x 3/4" PHF Tek, ZincCover Clip
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge, stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-35An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogEdge Mount, Full-Wrap Hinge GuardStainless Steel Continuous Hinge
MCK-HG322 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Brite dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel
Electrical Modifications (Suffix requireshanding)
• AMS Adjustable Monitoring Switch• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAsssembly. This added reinforcement will ensure the proper amount of materialfor threading the Adjusta-Screw, givingthe assembly the strength needed to lastthe life of the door. Remember to orderyour doors with reinforcement.
All the features of the HG-305Hinge/Guard plus 2” extensions. Thisunique design answers the problem ofadjusting doors where frames are notinstalled plumb or properly aligned. Notonly that, but the wrap-around edgeguard protects the door from unsightlydents and gouges and will deflectobjects, preventing further damage.Strategically located fasteners coupledwith the AdjustaScrew fastener allowthe door to be adjusted up to 3/8" withinthe channel of the hinge and distributethe load of the door down the entirelength of the jamb. The proper alignmentof the door to the frame will allow yourclosers, panics magnetic locks, electronicstrikes, and automatic operators to assistyou in meeting all your life safety coderequirements.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed
Fastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.
#10 x 1-1/4" PH U/C S.S.
10-32 x 3/4" PH U/C S. S.
1-3/8" RH, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door ClosedDoor Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-36 An ASSA ABLOY Group company An ASSA ABLOY Group companyJan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogEdge Mount, Full-Wrap Hinge GuardStainless Steel Continuous Hinge
MCK-HG323 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Brite dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel
Electrical Modifications (Suffix requireshanding)
• AMS Adjustable Monitoring Switch• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are not required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This extended wrap model allows youto sandwich the door between two leafsof stainless steel and thru-bolt themtogether. Ideal for salvaging doorswhich have split. This hinge has all ofthe features of the MCK HG-305 plus2" extensions.
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed
Fastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.
#10 x 1-1/4" PH U/C S.S.
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-Duty 14, Gauge 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBCcode standard 7-2 for positivepressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-37An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogSwing Clear, Full-Wrap Hinge GuardStainless Steel Continuous HingeMcKINNEY
MCK-HG326 OPTIONAL FEATURES
Door EdgeSpecify square of beveled edge• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom lengths - specify in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installing on a hollow metal door application we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAsssembly. This added reinforcement will ensure the proper amount of materialfor threading the Adjusta-Screw, givingthe assembly the strength needed to lastthe life of the door. Remember to orderyour doors with reinforcement.
This unique design solves the problemof aligning doors and lockingmechanisms crucial in any securityapplication. It also solves the problemwhen adjusting doors where frames arenot installed plumb or properly aligned.The incorporated edge guard protectsthe door from unsightly dents andgouges while also protecting the hingefrom vandalism. The proper alignmentof the door to the frame will allow yourclosers, panics, magnetic locks, electronicstrikes and automatic operators to assistyou in meeting all your life safety coderequirements.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.10-32 x 3/4" PH U/C S. S.1-3/8" RH, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedBarrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter .438 (7/16)
Heavy-duty 14, Gauge 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-38 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
McKINNEY Hinge CatalogEdge Mount, Safety HingeStainless Steel Continuous Hinge
MCK-FM327 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Torx Security Screws 1/2 x 12-24• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• MB Medical Bearings• RB Raised barrel
Electrical Modifications (Suffix requireshanding)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This unique design prevents smallfingers from getting pinched in thedoor. It is ideal for elementary schools,day care, childcare, and nursing homefacilities. This full-length continuoushinge also provides privacy by blockingsight lines into rooms. The hinge mustbe used with a cased open type frame.
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes
#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.
Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
This Hinge is not fire rated.
McKINNEY Hinge CatalogEdge Mount SecurityStainless Steel Continuous Hinge
CG-39An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
MCK-FM3500 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Plug weld hole pattern• Torx Security Screws 1/2 x 12-24• Special sheared leaf• Security Stud Option
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• RB Raised barrel
Electrical Modifications (Suffix requireshanding)• AMS Adjustable Monitoring Switch• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion*
• EPT Power Transfer Prep (Cut outOnly) For Von Duprin*
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This hospital tip, edge mount pin andbarrel type hinge is fabricated withextra-heavy duty components for use on high traffic, high abuse doors. Thehinge is specially designed and wellsuited for correctional facilities andother high security locations using 2"thick swing-type doors. Prison doors,gates, extremely tall doors and extraheavy doors are all good candidates forthe 3500 Security Hinge.
Abuse TestingExceeds ASTM-F-1450-A–The MCK-FM3500 was subjected to aseries of impacts generated by a RamPendulum System. 400 blows weredelivered to the lock, 100 ti the cornerof the vision lite and 150 each to threeseparate locations along the hinge. Inorder to pass, the door assembly cannotbe damaged to the extent that forcibleegress can be achieved, and the doormust be capable of being unlockednormally.
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed#1/2x12-24 PFHMS U/C S.S.
Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter .510
Heavy-duty 12 Gauge (.105”), 304stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-40 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
FM-3500 SECURITY STUD LOCATIONS FOR 8' 0"& 7' 0"
A 5/8" x 1/8" hole is required in the door to receive thesecurity stud.
FM-3500 SECURITY STUD OPTION
The 1/2" diameter x 1/4" proiected 3O4 stainless SecurityStud is permanently mounted to the frame leaf and extendsthrough the door leaf into the door for added security.There are 3 Security Studs required for the 7'O" hinge and4 required for the 8'O" hinge. A 5/8" x 1/8" hole is requiredin the door to receive the Security Stud.
CG-41 Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
McKINNEY Hinge CatalogFull Surface Security, for 1/8” Inset DoorsStainless Steel Continuous Hinge
MCK-FS3501 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing and
length in inches• Custom hole pattern• Plug weld hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• RB Raised barrel
Consult the Factory on other available options
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
For 1/8" inset doors. This hinge allowsfor perfect alignment for the retrofittingof doors in correctional facilities andother high security locations using 2"thick swing-type doors. Prison doors,gates, extremely tall doors and extraheavy doors are all good candidates forthe 3501 Security Hinge.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed#1/2 x 12-24 PFHMS U/C S.S.
Capacity (2" Doors) Supports weights up to 900lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter .510
Heavy-Duty 12 gauge (.105), 304stainless material.Finished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Abuse TestingExceeds ASTM-F-1450-92
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-42 An ASSA ABLOY Group companyOct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
MCK-FS3502 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Plug weld hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• RB Raised barrel
Consult the Factory on other available options
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This surface-mounted pin and barreltype hinge is fabricated with extra-heavy duty components and designedfor solving door sag problems on hightraffic - high abuse doors. This hinge iswell suited for correctional facilities andother high security locations using 2"thick swing type doors. Prison doors,gates extremely tall doors and extraheavy doors are all good candidates forthis 3502 Security Hinge.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed#1/2 x 12-24 PFHMS U/C S.S.
Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width(2" Doors)
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter .510
Heavy-Duty 12 gauge (.105), 304stainless materialFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Abuse TestingExceeds ASTM-F-1450-92
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-43An ASSA ABLOY Group company Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
MCK-HG3505 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• RB Raised barrel
Electrical Modifications (Suffix requireshanding)
• AMS Adjustable Monitoring Switch• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAsssembly. This added reinforcement will ensure the proper amount of materialfor threading the Adjusta-Screw, givingthe assembly the strength needed to lastthe life of the door. Remember to orderyour doors with reinforcement.
This unique design solves the problemof aligning doors and lockingmechanisms crucial in any securityapplication. It also solves the problemwhen adjusting doors where frames arenot installed plumb or properly aligned.The incorporated edge guard protectsthe door from unsightly dents andgouges while also protecting the hingefrom vandalism. The proper alignmentof the door to the frame will allow yourclosers, panics, magnetic locks, electronicstrikes and automatic operators to assistyou in meeting all your life safety coderequirements.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 1ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosed12-24 S.S. Phillips F.H.M.S.1-3/8 RH, 12-24 int., Adjusta Screws forcorrecting alignment problems up to 3/8"
Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 12 Gauge (.105”), hingeleafs; 16 Gauge returns on door leaf, 304stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-44Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MCK-FM3700 OPTIONAL FEATURES
• Custom lengths - specify handing andlength in inches
• Custom hole pattern• Tamper-proof security screws• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• RB Raised barrel
Electrical Modifications (Suffix)
• CC4 Concealed Circuit (4 Wire)• CC8 Concealed Circuit (8 Wire)• PT Power Transfer Prep (Cut out Only)
For Adams Rite, Securitron, Yale,Dorma & Centurion *
• EPT Power Transfer
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This edge-mounted pin & barrel typehinge is used on many of today’s hightraffic, high abuse doors. The hingeworks well in locations that usedanchor hinges, pivot reinforcementhinges or thrust pivot unit and hingesets. This hinge saves on special doorand frame preparation charges andmakes the installer’s job easier. It can be used on both fire labeled and non-labeled openings.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 2ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, Zinc
#10 x 1-1/4" PH U/C Zinc
Capacity (1-3/4" Doors)Supports weights up to 600 lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge, 1012 carbon steel,Gray Powder Coat
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogFull Surface, 1/8" InsetSteel Continuous Hinge
CG-45 Jan
uar
y 20
07
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
07
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MCK-FS3701 OPTIONAL FEATURES
• Custom lengths - specify handing andlength in inches
• 1-3/4" aluminum sleeve bolts
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• RB Raised barrel
• LL Lead-lined cover w/ 1/16” lead-lining
Consult the Factory on other available options
* Power Transfer Location Template mustaccompany your order
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
For 1/8" inset doors. This surface-mounted pin & barrel type continuoushinge can be used to repair both firelabeled and nonlabeled doors that havevery tight clearances. The hinge has abuilt-in 1/8" offset to assist in weatherseal and sound barrier areas.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 2ANSI / BHMA Standard A156.26
ANSI Cross ReferenceMounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes1/4-20 x 3/4" PPH Tek, SD, Zinc#8 x 3/4 PFH Tek, ZinkCover Clip
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Doors)Supports weights up to 600 lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge 1012 carbon steel,Gray Powder Coat
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogFull Surface Flush MountStainless Steel Continuous Hinge
CG-46Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MCK-FS3702 OPTIONAL FEATURES
• Custom lengths - specify handing andlength in inches
• 1-3/4" aluminum sleeve bolts
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• RB Raised barrel• LL Lead-lined cover w/ 1/16" lead-
lining
Consult the Factory on other available options
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
For flush doors. This surface-mountedpin & barrel type continuous hinge canbe used to repair both fire labeled andnon-labeled doors that have very tightclearances.
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 2ANSI / BHMA Standard A156.26
ANSI Cross ReferenceMounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes1/4-20 x 3/4" PPH Tek, SD, Zinc#8 x 3/4 PFH Tek, ZinkCover Clip
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Door)Supports weights up to 600 lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge, 1012 carbon steel,Gray Powder Coat
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogHalf SurfaceSteel Continuous Hinge
CG-47 Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MCK-HS7303 OPTIONAL FEATURES
• US32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern• Tamper-proof security screws• 1-3/4" aluminum sleeve bolts• Special sheared leaf
Options (Suffix may require handing)• DD Dutch door hinges (DD Form
Required)• HT Hospital tips• RB Raised barrel• LL Lead-lined cover w/ 1/16" lead-
lining
Electrical Modifications (Suffix requireshanding)• PT Power Transfer Prep (Cut out frame
leaf only) For Adams Rite, Securitron,Yale, Dorma & Centurion*
• EPT Power Transfer Prep (Cut out,frame leaf only) For Von Duprin*
Consult the Factory on other available options
When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.
This half-surface pin & barrel typecontinuous hinge can be used to repairboth fire labeled and non-labeledopenings. The hinge fits into the gapleft after standard butt hinges areremoved. It can assist in reversing thehanding of a door, or to reverse theswing of a door hung in an evenly-rabbetted frame. (Please call the factoryat 800-346-7707. for instructions onunevenly-rabbetted frames.)
C USLISTED
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Grade 2ANSI / BHMA Standard A156.26
ANSI Cross Reference
Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, Zinc#10 x 1-1/4" PH U/C ZincCover Clip#8 x 3/4" PHF Tek, Zinc
Fastener CoverBrushed Aluminum
Capacity (1-3/4" Door)Supports weights up to 600 lbs.4'0" maximum door width
Hole PatternSymmetrically templatedNon-handed
Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings
Exterior Barrel Diameter.438 (7/16)
Heavy-duty 14 Gauge, 1012 carbon steel,Gray Powder Coat
Door Closed
Door Open 90°
Classified in accordance with UBC code standard 7-2 for positive pressure
Fire Rating3 hours- hollow metal doors mounted
singly
90 minutes- hollow metal and compositecore wood fire doors
20 minutes- wood doors
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-48Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
CUTTING HINGES TO CUSTOM LENGTHS
Pin & Barrel Hinges
1. The following instructions will apply to all McKinney pinand barrel hinges. The general instructions apply to both 300 and 3700 series hinges.
2. Determine the amount that the hinge needs to beshortened. Note the hand of the hinge before begining tolay out your cut. All cuts will be done at the bottom ofyour hinge assembly making sure to leave the gang holepattern at the top.
3. Measure from the top down and scribe a cut line on yourleaf at the desired length.
4. Cut the hinge to length with a hacksaw, going through theleafs, barrel and pin. If necessary, use a file to removesharp edges and deburr.
5. Slide the stainless steel pin out approximately 1" makingsure the assembly stays together as one unit. Remove 1/4"from the end of the pin using a hacksaw and then pushback into it's original position.
6. Using a pair of vice-grips, crimp the end of the steel barrelmaking sure the hinge pin will not slide out.
6.
McKINNEY Hinge Catalog300 SeriesStainless Steel Edge Guard
CG-49 Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MCK EG-308 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern for lead line doors• DD – Dutch door guard application• #10-32 x 3/4 PFH U/C Stainless• AS - Adjusta Screws for correcting
alignment problems up to 3/8”
Adjusta Screw assemblies are approved for use on labeled doors. UL Certificationfile #R15384 (N)
This edge guard which can make doorsadjustable to non-plumb frames protectsthe leading edge of the door is used inconjunction with the McK-HG305 fora balanced aesthetic look.
When using this edge guard in aHollow Metal Door application, westrongly suggest your doors be orderedand manufactured with reinforcementat the lock side of the door for properuse of the Adjusta-Screw Assembly.
This added reinforcement will ensurethe proper amount of material forthreading the Adjusta-Screw, giving the strength needed to last the life ofthe door. This reinforcement onlyapplies to Adjusta-Screw assembly andis not needed for any other hardwareapplication.
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Mounting Hardware#10 x 1-1/4 PFH U/C Stainless
Door EdgeSpecify square of beveled edge
Hole PatternSymmetrically templatedNon-handed
Heavy-Duty 16 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed Door Open 90°
Classified in accordance with UBCcode standard 7-2 fire test of doorassemblies for positive pressure
– also Miscellaneous Firedoor Accessory 8N60
Fire RatingUp to 1-1/2 hours, for use on wood,plastic coated wood composite andhollow metal fire rated door.
MAY NOT APPLY TO ALL WOODDOORS IN ACCORDANCE WITHUBC STANDARD CODE 7-2.PLEASE CONSULT FACTORY FOR SPECIFIC WOOD DOORAPPLICATIONS.
• Flush Bolts• ASA Strike• 86 edge and ASA lock• Hospital latch• 161 cutoutMeasurements should be given from Top of door to centerline of cutout. The EdgeGuard Order Form must accompany your order.Please note that hinge cut outs are notavailable at this time
HARDWARE CUTOUTS(requires handing)
McKINNEY Hinge Catalog300 SeriesStainless Steel Edge Guard
1-800-346-7707www.mckinneyhinge.com
MCK EG-C308 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern for lead line doors• DD – Dutch door guard application
This edge guard which protects theleading edge of the door from dents and gouges is used in conjunction withthe McK-HG315 for a balancedaesthetic look.
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Mounting Hardware#10 x 1-1/4 PFH U/C Stainless
Door EdgeSpecify square of beveled edge
Hole PatternSymmetrically templatedNon-handed
Heavy-Duty 16 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed
Door Open 90°
Classified in accordance with UBCcode standard 7-2 fire test of doorassemblies for positive pressure
– also Miscellaneous Firedoor Accessory 8N60
• Flush Bolts• ASA Strike• 86 edge and ASA lock• Hospital latch• 161 cutoutMeasurements should be given from Top of door to centerline of cutout. The EdgeGuard Order Form must accompany your order.Please note that hinge cut outs are notavailable at this time
HARDWARE CUTOUTS(requires handing)
CG-50Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
An ASSA ABLOY Group company
Fire RatingUp to 1-1/2 hours, for use on wood,plastic coated wood composite andhollow metal fire rated door.
MAY NOT APPLY TO ALL WOODDOORS IN ACCORDANCE WITHUBC STANDARD CODE 7-2.PLEASE CONSULT FACTORY FOR SPECIFIC WOOD DOORAPPLICATIONS.
McKINNEY Hinge Catalog300 SeriesStainless Steel Edge Guard
CG-51 Ap
ril 2
003
Oct
ob
er 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MCK EG-T308 OPTIONAL FEATURES
• 32 Bright Polished stainless (629)• Custom lengths - specify handing and
length in inches• Custom hole pattern for lead line doors• DD – Dutch door guard application• #10-32 x 3/4 PFH U/C Stainless• AS - Adjusta Screws for correcting
alignment problems up to 3/8”
Adjusta Screw assemblies are approved for use on labeled doors. UL Certificationfile #R15384 (N)
The integral overlapping astragal of thisedge guard provides an additional levelof security by acting as a latchprotector. It is ideal for exterior pairs ofdoors that require protection fromvandalism. This edge guard also makesdoors adjustable to non-plumb frames.
When using this edge guard in aHollow Metal Door application, westrongly suggest your doors be orderedand manufactured with reinforcementat the lock side of the door for properuse of the Adjusta-Screw Assembly.
This added reinforcement will ensurethe proper amount of material forthreading the Adjusta-Screw, giving thestrength needed to last the life of thedoor. This reinforcement only applies to Adjusta-Screw assembly and is notneeded for any other hardwareapplication.
6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2
Available Sizes
Door Size Hinge Length Hinge Length MM
Mounting Hardware#10 x 1-1/4 PFH U/C Stainless
Door EdgeSpecify square of beveled edge
Hole PatternSymmetrically templatedNon-handed
Heavy-Duty 16 Gauge, 304 stainless steelFinished in 32D (630)
Door Closed Door Open 90°
Classified in accordance with UBCcode standard 7-2 fire test of doorassemblies for positive pressure
– also Miscellaneous Firedoor Accessory 8N60
Fire RatingUp to 1-1/2 hours, for use on wood,plastic coated wood composite andhollow metal fire rated door.
MAY NOT APPLY TO ALL WOODDOORS IN ACCORDANCE WITHUBC STANDARD CODE 7-2.PLEASE CONSULT FACTORY FOR SPECIFIC WOOD DOORAPPLICATIONS.
• Flush Bolts• ASA Strike• 86 edge and ASA lock• Hospital latch• 161 cutoutMeasurements should be given from Top of door to centerline of cutout. The EdgeGuard Order Form must accompany your order.Please note that hinge cut outs are notavailable at this time
HARDWARE CUTOUTS(requires handing)
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-52Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
MT-SP-100
Right angle drive skewdriverThis member of McKinney's line of installation tools is the MT-SP100 Right Angle Drive Skewdriver. Its unique gearingdesign gives conventional screwdriver action on hard-to-reach fasteners, and the adjustable stabilizer wing provides extrastability in high torque and restricted locations. Heavy-duty construction- with die-cast housing and hardened steel gears.
This tool is especially helpful when installing our MCK-HG310 and MCK-HG311 models.
An ASSA ABLOY Group company
1.800.346.7707 • PR
ICE
BO
OK
©M
cKIN
NE
YP
roducts Com
pany 2006
McKINNEY CG53STAINLESS AND STEEL CONTINUOUS
Hinge Door Frame ClearancesFastener Information
July 1, 2006
®
Under-sizing Required For All Door Applications:• Hinge Side Clearance.......................Dimension Specific Per Model• Lock side clearance..........................1/8" Per N.F.P.A. (For single as well as between a pair of doors)• Allowance for frame irregularities...1/16"
Standard Non-Adjustable Application Formulas
Example for Standard Single Door:MODEL: (MCK-HG305) . . . . . . . . .3/8" Hinge Side Clearance
1/8" Lock-side Clearance+1/16" Frame Irregularity9/16" (As shown in 300 Series Standard Non-Adjustable Chart Page CG54)
Example for Standard Pair of Doors:MODEL: (MCK-HG305) . . . . . . . . .3/8" Hinge Side Clearance (Door 1)
3/8" Lock-side Clearance (Door 2)1/8" Lock-side Clearance (Between Pair of Doors)
+1/16" Frame Irregularity15/16" (As shown in 300 Series Standard Non-Adjustable Chart Page CG54)
For adjustable models used in an Adjustable Application, an additional 1/8" of clearance isrequired as shown below
Example for Standard Single Door:MODEL: (MCK-HG305) . . . . . . . . .3/8" Hinge Side Clearance
1/8" Lock-side Clearance1/16" Frame Irregularity+1/8" Additional Adjustment Clearance
11/16” (As shown in 300 Series Adjustable Chart Page CG55)
Example for Standard Pair of Doors:MODEL: (MCK-HG305) . . . . . . . . .3/8" Hinge Side Clearance (Door 1)
3/8" Hinge Side Clearance (Door 2)1/8" Lock-side Clearance (Between Pair of Doors)
1/16" Frame Irregularity1/8" Additional Adjustment Clearance (Door 1)
+1/8" Additional Adjustment Clearance (Door 2)1-3/16" (As shown in 300 Series Adjustable Chart Page CG55)
1.80
0.34
6.77
07 •
PR
ICE
BO
OK
©
McK
INN
EY
Pro
duct
s C
ompa
ny 2
006
An ASSA ABLOY Group company
McKINNEY CG54300 Series Pin & Barrel
Stainless Steel Continuous HingesClearance Dimensions
®
July 1, 2006
Standard “Non-Adjustable” Application
MODEL Clearance (A) Single Door Pair of Doors
MCK-FM300 1/4 7/16 11/16
MCK-FS301 1/8 5/16 7/16
MCK-FS302 1/8 5/16 7/16
MCK-FS303 1/8 5/16 7/16
*MCK-HM304 1/8 5/16 7/16
MCK-HG305 3/8 9/16 15/16
*MCK-HG306 1/8 5/16 7/16
*MCK-FS309 1/8 5/16 7/16
MCK*HG310 1/4 7/16 11/16
*MCK-HG311 1/8 5/16 7/16
MCK-HG315 1/4 7/16 11/16
*MCK-FS21 1/8 5/16 7/16
MCK-HG322 5/16 1/2 13/16
MCK-HG323 5/16 1/2 13/16
MCK-HG326 3/8 9/16 15/16
MCK-FM327 11/16 7/8 1-9/16
*Will work with Industry Standard Clearances.
“Adjustable” Application
Total TotalUnder-sizing Under-sizing
Hinge Side For ForMODEL Clearance (A) Single Door Pair of Doors
MCK-HG-305 3/8 11/16 1-3/16
MCK-HG-310 1/4 9/16 15/16
MCK-HG-322 5/16 5/8 1-1/16
MCK-HG-323 5/16 5/8 1-1/16
MCK-HG-326 3/8 11/16 - 3/16
Proper door reinforcement is required for adjustable feature.
An ASSA ABLOY Group company
1.800.346.7707 • PR
ICE
BO
OK
©M
cKIN
NE
YP
roducts Com
pany 2006
McKINNEY CG55300 Series Pin & Barrel
Stainless Steel Continuous HingesClearance Dimensions
July 1, 2006
®
Standard “Non-Adjustable” Application
Total TotalUnder-sizing Under-sizing
Hinge Side For ForMODEL Clearance (A) Single Door Pair of Doors
MCK-EG308 1/16 3/16 1/4
MCK-EG-C308 1/16 3/16 1/4
MCK-EG-T308 1/16 1/4
In a stand-alone application, where the MCK-EG-T308 is used ona pair of doors while the opposite door contains no edge guard, theTotal Under-sizing for the pair of doors would be 3/16".
“Adjustable” Application
Total TotalUnder-sizing Under-sizing
Hinge Side For ForMODEL Clearance (A) Single Door Pair of Doors
MCK-EG308 1/16 5/16 1/2
MCK-EG-T308 1/16 1/2
In a stand-alone application, where the MCK-EG-T308 is used ona pair of doors while the opposite door contains no edge guard, theTotal Under-sizing for the pair of doors would be 5/16".Proper door reinforcement is required for adjustable feature.
1.80
0.34
6.77
07 •
PR
ICE
BO
OK
©
McK
INN
EY
Pro
duct
s C
ompa
ny 2
006
An ASSA ABLOY Group company
McKINNEY CG56300 Series Pin & Barrel
Stainless Steel Continuous HingesClearance Dimensions
®
July 1, 2006
Standard “Non-Adjustable” Application
Total TotalUnder-sizing Under-sizing
Hinge Side For ForMODEL Clearance (A) Single Door Pair of Doors
MCK-FM3700 1/4 7/16 11/16
*MCK-FS3701 1/8 5/16 7/16
*MCK-FS3702 1/8 5/16 7/16
*MCK-HS3703 1/8 5/16 7/16
* Will work with Industry Standard Clearances.
McKINNEY Hinge CatalogEdge MountStainless Steel Continuous Hinge
CG-53 Jan
uar
y20
07©
McK
INN
EY
Pro
duc
tsC
omp
any
2007
1-800-346-7707www.mckinneyhinge.com
An ASSA ABLOY Group company
PREVENTING MORTAR FROM BREAKING DRILLS AND TAPS
Preventing mortar from breaking drills and tapsOne way to ease installation of continuous hinges in the field on new construction projects is to coordinate with the anchoringand hollow metal supplier prior to frame installation, by placing a 1/4" or 3/8" strip of expanded polystyrene insulation on theback of the hollow metal frame as shown below. When the frames are grouted in, the foam backer will allow drilling andtapping without dulling or breaking the installers bits.
You'll be a hero with the installer, contractor and architect!
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross Reference
iAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
This cross reference is intended for theuse of architects and contract hardwaredistributors in establishing comparisonsbetween the hinge products ofMcKINNEY and other manufacturers.
These listings have been carefullycompiled from the most recentcatalogs of the manufacturers involvedand it is believed that it represents afair comparison between the product
lines. While all contract gradehardware is to be manufactured inaccordance with BHMA and ANSIstandards, McKINNEY assumes noresponsibility for the accuracy of thislist of competitors’ numbers andsuggests that both manufacturers’catalog and templates be consulted foradditional information.
McKINNEY welcomes theopportunity to consult with any
architect, distributor, contractor orbuilder at any time regarding anymatter concerning the specification of our products.
Note: McKINNEY pioneered the use of “OilLite” bearings in 1935 for improved bearingperformance. The standard five knucklebearing hinges manufactured by McKINNEYare furnished with oil-impregnated bearings(TA). However, ball bearings can be suppliedas specified.
Hinges, Spring Hinges, Misc.ANSI Hinge Standard Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iiBommer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iiiHager Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ivLawrence Brothers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vStanley Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viUnited States Government Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii
Aluminum Continuous HingesMarkar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ixRoton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ixSelect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ixStanley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ix
Stainless Continuous HingesGallery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viiMarkar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viiStanley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii
Finish SymbolsUnited States Government Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xLawrence Brothers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xStanley Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xHager Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x
Table of Contents Page
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceANSI Hinge Standard Numbers
ii An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
ANSI McKINNEY
A5212 TA3374 (32-32D)
TA374 (32-32D)TA3324 (32-32D)
A5311 T4A3381 (32-32D)TA381 (32-32D)TA3361 (32-32D)
A5361 T4A3385 (32-32D)A5411 T4A3382 (32-32D)
TA382 (32-32D)TA3362 (32-32D)
A5412 TA2372 (32D)TA372 (32D)
A5551 TA392TA393
A8111 T4A3786TA786TA3750
A8112 TA2714TA714TA2731
A8121 T4A3795
TA795TA3765
A8122 TA2895A8133 T2714
T714T2731
A8142 TA2714 Type II
A8152 TA2714 Type IA8173 2705A8211 T4A3784
TA784
TA3764A8212 TA2774
TA774TA2724
A8221 T4A3789
TA789TA3769
A8233 T2774
A8311 T4A3781
ANSI McKINNEY
A1612 TA3383
A1711 TA3329A1882 DS-6A2111 T4A3386
TA386TA3350
A2112 TA2314TA314
TA3331A2133 T2314A2142 TA2314 - Type IIA2152 TA2314 - Type I
A2211 T4A3384TA384TA3364
A2212 TA3374TA374TA3324
A2311 T4A3381
TA381TA3361
A2361 T4A3385A2411 T4A3382
TA382TA3362
A2412 TA372
TA2372A2551 TA392
TA393TA5392
A2742 EP-5A5111 T4A3386 (32-32D)
TA386 (32-32D)TA3350 (32-32D)
A5112 TA2314 (32-32D)TA314 (32-32D)TA3331 (32-32D)
A5133 T2314 (32-32D)A5211 T4A3384 (32-32D)
TA384 (32-32D)TA3364 (32-32D)
ANSI McKINNEY
A8311 TA781
TA3761A8312 TA2771
TA771TA2741
A8321 T4A3797TA797TA3767
A8361 T4A3785A8411 T4A3782
TA782TA3762
A8412 TA2772TA772
TA2732A8421 T4A3796
TA796TA3769
A8433 T2772A8551 TA792
TA793
TA5792K61091 CS1K63201 4007K81041 3", 4", 5", 6" 1001
8" 9001K81071 1502K81071F 1502
K81081 1572K8108F 1572K81111 8" 19001K81131 HS1001K81151 6 X 4-1/2 1001K82011 8007
K82021 H8007K82183 3001K87431 35K87441 9" 451
11" 45213" 453
ANSI Hinge Standard and McKINNEY Equivalent Numbers
Note: NFPA requires that all hinges or pivots, except spring hinges, installed on labeled doors be of thebearing type. Acceptable hinge material - steel or stainless steel. (Spring hinges available in steel only.)Ball Bearings available upon request.
ANSI # McKINNEY # ANSI # McKINNEY # ANSI # McKINNEY #
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceBommer Industries Inc. Numbers
iiiAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
Feature Bommer McKINNEY
Non-Removable Pin N NRP (Suffix)
Security Stud S SSF (Suffix)Non-Removable Pinwith Security Stud
A NRP x SSF (Suffix)
Maximum Security Stud M PSF (Suffix)
Hospital Tip H HT (Prefix)
Decorative Ball Tip Decorative Ball Tip BT (Suffix)
Decorative Steeple Tip Decorative Steeple Tip ST (Suffix)
Stainless Steel Pins J SSP (Suffix)Brass Pins K BR
BB5042 RBMTA2314-32D
BB5044 RBT4A3786
BB5045 RBT4A3386
BB5046 RBT4A3386-32D
BB5050 TA2714 Slip-in Type 2BB5051 TA2314 Slip-in Type 2
BB5052TA2314-32D Slip-in Type 2
BB5060 TA2714 CCBB5061 TA2314 CC
BB5062 TA2314-32D CC
BB5064 T4A3786 CC
BB5065 T4A3386 CC
BB5066 T4A3386-32D CC5100 T2774
BB5101 TA3374
BB5102 TA3374-32D
BB5104 T4A3784
BB5105 T4A3384BB5106 T4A3384-32D
BB5124 T4A3789
BB5200 TA2771
BB5201 TA3341
BB5204 T4A3785BB5205 T4A3385
BB5224 T4A3797
BB5226 T4A3397-32D
5300 T2772
BB5300 TA2772BB5301 TA2372
BB5302 TA2372-32D
BB5304 T4A3782
BB5305 T4A3382
MB-1 MG-16
170 352410 451
2430 453
3023 HS1001
3024 19001
3029 10013029 (8") 9001
4310 1502
4313 1572
5000 T2714
5001 T23145002 T2314-32D
BB5000 TA2714
BB5001 TA2314
BB5002 TA2314-32D
BB5004 T4A3786BB5005 T4A3386
BB5006 T4A3386-32D
BB5010 TA2798
BB5011 TA2398
BB5012 TA2398-32DBB5014 T4A3786
BB5015 T4A3386
BB5016 T4A3386-32D
BB5020 TA2895
BB5021 TA2395BB5022 TA2395-32D
BB5024 TA3795
BB5026 T4A3395-32D
BB5034 TA792
BB5040 RBMTA2714BB5041 RBMTA2314
BB5306 T4A3382-32D
BB5324 T4A37967112 4007RB
7112 4007MRB
7512 8007
H7512 H8007
7811 30017812 J3001
8000 T714
8001 T314
8002 T314-32D
BB8000 TA714BB8001 TA314
BB8002 TA314-32D
BB8004 TA786
BB8005 TA386
BB8006 TA386-32DBB8024 TA795
BB8034 TA792
BB8036 TA392
BB8040 RBMTA714
BB8044 RBMTA786BB8060 TA714 CC
BB8064 TA786 CC
BB8100 TA774
BB8101 TA374
BB8102 TA374-32DBB8104 TA784
BB8105 TA384
BB8106 TA384-32D
BB8124 TA789
BB8200 TA771BB8201 TA371
BB8202 TA371-32D
BB8204 TA781
BB8205 TA381
BB8206 TA381-32DBB8224 TA797
BB8300 TA772
BB8301 TA372
BB8302 TA372-32D
BB8304 TA782BB8305 TA382
BB8306 TA382-32D
BB8324 TA796
Bommer Industries Inc. Numbers and McKINNEY Equivalent Numbers
Bommer # McKINNEY # Bommer # McKINNEY # Bommer # McKINNEY #
Options
1-800-346-7707www.mckinneyhinge.com
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceHager Catalog Numbers
iv An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
OptionsFeature Hager McKINNEY
Suffix for Electric Hinges
1191 T2314BB1191 TA2314BB1193 TA3313BB1199 T4A33861250 15021253 1572BB1264 T4A3789BB1265 T4A4789BB1266 T4A3797BB1260 TA2895BB1261 TA4895BB1262 T4A3795BB1263 T4A4795BB1265 T4A4789BB1270 T4A3796BB1277 TA2714 Slip-inBB1278 TA2714 Slip-inRC1279 RC27141279 T2714BB1279 TA2714WTBB1279 TA2798BB1577 TA2314 Slip-inBB1578 TA2314 Slip-in1741 1400RC1741 14141804 7031808 705RC1841 1458BB2098 T4A3384BB2109 T4A3381BB2108 T4A3385BB2110 TA2371BB2112 TA2372BB2113 T4A3382BB2169 T4A3781BB2168 T4A3785BB2171 TA2771BB7508 TA5792BB8508 TA5392
E ESETM CCxMMETW CCEMN MMEIS CS
Hager Catalog Numbers and McKINNEY Equivalent Numbers
Hager # McKINNEY # Hager # McKINNEY # Hager # McKINNEY #
BB7506 TA792BB7507 TA5792BB800 TA314BB801 TA374BB802 TA371BB803 TA372BB850 TA386BB851 TA384BB852 TA381BB853 TA382BB858 TA393920 T2731AB920 TA2731BB8505 TA393BB8506 TA392BB8507 TA53921250 15021256 81330BB1109 TA33741129 T2774BB1129 TA2774BB1138 T4A3784BB1163 T4A3782BB1168 T4A37861173 T2772BB1173 TA2772BB1174 TA3713
417 BP-10418 BP-11451 DLS-8452 DLS-8453 DLS-8454 DLS-8495 R1-TOP496 R2-CENTER497 R3-BOTTOM600 EPS & DS6610 DS-6700 T714BB700 TA714BB701 TA774BB702 TA771BB703 TA772BB750 TA786BB751 TA784BB752 TA781BB753 TA782BB7501 TA795BB7501 TA5795BB7511 TA789BB7512 TA5789BB7523 TA797BB7534 TA796BB7505 TA793
Raised Barrel RBB RBM (Prefix)
Raised Barrel RBS RBS (Prefix)
Ball Bearing BB TB (Prefix)
Oilite Bearing OB TA (Prefix)
Triple Plate CP S (Prefix)
Brass Pin BP BR (Suffix)
Stainless Steel Pin SP SSP (Suffix)
Set Screw in Barrel NRP NRP (Suffix)
Spun or Riveted Pin FRP FR/SP (Suffix)
Safety Stud SH SSF (Suffix)
Hospital Tip HT HT (Prefix)
Steeple Tip ST ST (Suffix)
Ball Tip BT BT (Suffix)
Round Corner RC RC (Prefix)
“Luma Sheen” LS AP (Finish)
“Luma-color” Black L1 D-4 (Finish)
“Luma-color” Dark Bronze L2 D-3 (Finish)
“Luma-color” Medium Bronze L3 D-2 (Finish)
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceLawrence Catalog Numbers
vAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
Lawrence Brothers Numbers and McKINNEY Equivalent Numbers
Lawrence # McKINNEY # Lawrence # McKINNEY # Lawrence # McKINNEY #
CHP-1 EP-5
TPU-2 1/2 TA792TPU-2-1/2-A TA392SC2500 1400SC2514 1414SC2558 1458BB4101 TCA2714BB4101-32D TCA2314-32D
BB4101-A TCA2314BB4101WT TCA2798RB-BB4101 RBM-TA2714BB4105 TA2714 Slip-inBB4105-A TA2314 Slip-in4168 15024181 T2714
RC4181 RC27144181-A T23144181xRP T2705BB4301 TA27724381 T2772BB4601 TA27744681 T2774
BB4701 TA2771BB4901 TCA2714BB4901-32D TCA2314-32DBB4901-A TCA23144981 T27144981-32D T2314-32D
4981A T2314
BB4951 TCA3786BB4951-32D TCA3386-32DBB4951A TCA3386BB5151 T4A3786BB5151-32D T4A3386-32DRB-BB-5151 RBM-T4A3786BB5151-A T4A3386
BB5152 T4A3795BB5351 T4A3782BB5351-32D T4A3382-32DBB5351-A T4A3382BB5352 T4A3796BB5601 TA3774BB5601-A TA3374
BB5601-32D TA3374-32DBB5651 T4A3784BB5651-A T4A3384BB5652 T4A3789BB5751 T4A3781BB5751-32D T4A3381-32DBB5751-A T4A3381
BB5752 T4A3797BB6154A TA33297106 CSS98040 7038080 705
BB9101 TA714
BB9101-A TA314BB9151 TA786BB9151-32D TA786-32DBB9151-A TA386BB9152 TA7959181 T714BB9301 TA772
BB9301-A TA372BB9351 TA782BB9351-A TA382BB9352 TA796BB9601 TA774BB9601-A TA374BB9651 TA784
BB9651-A TA384BB9652 TA789BB9701 TA771BB9701-A TA371BB9751 TA781BB9751-A TA381BB9752 TA797
CEC CCCES CSSW ES
Suffix for Electric Hinges
Ball Bearings available upon request.
OP-1 R1-TOPES-1 DS-6DLS-1 DLS-8JB-1 MG-16BP-1 BP-10/BP-11DAP-3 EP-5BB98 T4A3384FBB108 TA3374FBB109 T4A3381FBB109-1/2 T4A3385FBB112 TA2372FBB113 T4A3382FBB138 T4A3784FBB163 T4A3782FBB167 TA2774F167 T2774FBB168 T4A3786/MPB68FBB169 T4A3781FBB169-1/2 T4A3785FBB171 TA2771F173 T2772FBB173 TA2772F179 T2714/MP79FBB179 TA2714/MPB79FBB179WT TA2798FBB179 Slip-in TA2714 Slip-inF191 T2314FBB191 TA2314/MPB91FBB191 Slip-in TA2314 Slip-in
1-800-346-7707www.mckinneyhinge.com
©M
cKIN
NE
YP
rod
ucts
Com
pan
y20
06
McKINNEY Hinge CatalogCross ReferenceStanley Catalog Numbers
vi An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril2
003
Suffix for Electric Hinges
Stanley Catalog Numbers and McKINNEY Equivalent Numbers
Stanley # McKINNEY # Stanley # McKINNEY # Stanley # McKINNEY #
Feature Stanley McKINNEY
Rust-Resistant Base K S (Prefix)
Solid Brass Ball Tips Solid Brass Ball Tips BT (Suffix)Steeple Tips Steeple Tips ST (Suffix)Hospital Tip HT HT (Prefix)Shear Resisting Stud SRS PSF (Suffix)Non Removable Pin NRP NRP (Suffix)Fast Spun Pin FSP SP (Suffix)
Security Stud Sec. St. SSF (Suffix)No Hole Prefix NH BLANKRaised Barrel RB RBM/RBS (Prefix)Slip-in Slip-in S1H Type 1
S1H Type 2 (Prefix)
Options
CB1920 TA774
CB1921 TA784CB1930 TA771CB1931 TA781CB1941 TA789CB1942 TA5789CB1948 TA795CB1949 TA5795
CB1951 TA797CB1959 TA796CB1960 TA314CB1961 TA386CB1967* TA393CB1968* TA392CB1969 TA5392
CB1970 TA372CB1971 TA382CB1980 TA374CB1981 TA384CB1990 TA371CB1991 TA3812060 1502
2063 1572
CE CC
CS CSES ESCS MMCExCS CCxCS
Note: *Available only in Bronze.
FBB199 T4A3386 / MPB99FBB211* TA793FBB212* TA792FBB213* TA5792FBB221* TA393FBB222* TA392FBB223* TA5392241 2714FBB248 TA2895FBB258 TA4895FBB264 T4A3789FBB266 T4A3797FBB268 T4A3795FBB269 T4A3796FBB274 T4A4789FBB278 T4A4795BB601-8" TB786-8"0700 T2731CB700 TA2731741 1400RD741 1414RD758 14581900 T714CB1900 TA714CB1901 TA786CB1907* TA793CB1908* TA792CB1909* TA5792CB1910 TA772CB1911 TA782
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceUnited States Government Numbers
viiAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
003
F1820 451
F1840 452F1840 4532102 A3313T2102 TA3313TH2102 HTA33132105 A2714T2105 TA2714
TH2105 HTA27142106 A2314T2106 TA23142107 A27142107 A2798T2107 TA2714T2107 TA2798
TH2107 HTA27142112 4A3386T2112 T4A3386TH2112 HT4A33862115 4A3786T2115 T4A3786TH2115 HT4A3786
2117 4A3786PT2117 T4A3786P
TH2117 HT4A3786P
2126 23142127 2714T2127 T27142127H 27142CBR2135 A2772T2135 TA2772TH2135 HTA2772P
T2136 T4A3382TH2136 HT4A3382T2137 T4A3782TH2137 HT4A3782T2139 T4A3782PTH2139 HT4A3782PT2142 TA3374
TH2142 HTA3374T2143 TA3774TH2143 HTA3774T2145 TA2774TH2145 HTA2774PT2146 T4A3384TH2146 HT4A3384
T2147 T4A3784TH2147 HT4A3784
T2149 T4A3784P
TH2149 HT4A3784PT2155 TA2771TH2155 HTA2771PT2156 T4A3381TH2156 HT4A3381T2157 T4A3781TH2157 HT4A3781
T2159 T4A3781PTH2159 HT4A3781PT2160 T4A3789T2161 T4A3789PT2163 T4A3797T2164 T4A3797P2170 3305
T2170 T33052171 2705T2171 T27052171H SC7052CBR2176 SC7032176G SC7032CBR2331A 1001
2332A 9001
United States Government Numbers and McKINNEY Equivalent Numbers
U.S. # McKINNEY # U.S. # McKINNEY # U.S. # McKINNEY #
Gallery, Markar, Stanley and McKINNEY Equivalent NumbersMcKINNEY # Gallery # Markar # Stanley #
Steel Stainless Steel Stainless Steel Stainless Steel Stainless
MCK-FM3700 MCK-FM300 CH-941 951 FM200 FM300 641 651
MCK-HG3705 MCK-HG305 CH-942 952 HG305 652
MCK-HG3715 MCK-HG315 CH-943 953 HG315 643 653
MCK-HM3704 MCK-HM304 CH-944 954 HM204 HS303 644 654
MCK-HG3706 MCK-HG306 CH-945 955 HG306 645 655
MCK-HG3711 MCK-HG311 CH-946 956 SFS/SC-209 HG311 646 656
MCK-FS3702 MCK-FS302 CH-947 957 FS202 FS3-2 647 657
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceContinuous Aluminum Geared Hinge
viii An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
006
Hea
vy D
uty
Hea
vy D
uty
Stan
dard
Wei
ght
Hea
vy D
uty
Stan
dard
Wei
ght
Flus
h M
ount
Con
ceal
ed w
ith
Stop
s
Roton, Stanley, Markar, Select and Pemko Product Numbers and McKINNEY Equivalent Numbers
Stan
dard
Wei
ght
1 ⁄ 16"
Ins
et M
ount
wit
h D
oor
Lea
f L
ip
MCK-22HD 83" Clear 780-041 665 CFS 83MCK-22HD 83" Bronze 780-041 665 DFS 83MCK-22HD 85" Clear 780-041 665 CFS 85MCK-22HD 85" Bronze 780-041 665 DFS 85MCK-22HD 95" Clear 780-041 665 CFS 95MCK-22HD 95" Bronze 780-041 665 DFS 95MCK-22HD 120" Clear 780-041 665 CFS 120MCK-22HD 120" Bronze 780-041 665 DFS 120MCK-22HD 83" Clear 780-041HD 665HD CFS 83FDMCK-22HD 85" Bronze 780-041HD 665HD DFS 83FDMCK-22HD 85" Clear 780-041HD 665HD CFS 85FDMCK-22HD 85" Bronze 780-041HD 665HD DFS 85FDMCK-22HD 95" Clear 780-041HD 665HD CFS 95FDMCK-22HD 95" Bronze 780-041HD 665HD DFS 95FDMCK-22HD 120" Clear 780-041HD 665HD CFS 120FDMCK-22HD 120" Bronze 780-041HD 665HD DFS 120FDMCK-12HD 83" Clear 780-112 661 SL-11CL CFM 83SLFMCK-12HD 83" Bronze 780-112 661 SL-11BR DFM 83SLFMCK-12HD 85" Clear 780-112 661 SL-11CL CFM 85SLFMCK-12HD 85" Bronze 780-112 661 SL-11BR DFM 85SLFMCK-12HD 95" Clear 780-112 661 SL-11CL CFM 95SLFMCK-12HD 95" Bronze 780-112 661 SL-11BR DFM 95SLFMCK-12HD 120" Clear 780-112 661 SL-11CL CFM 120SLFMCK-12HD 120" Bronze 780-112 661 SL-11BR DFM 120SLFMCK-12HD 83" Clear 780-112HD 661HD FM-2000 SL-11HDCL CFM 83SLFHDMCK-12HD 83" Bronze 780-112HD 661HD FM-2000 SL-11HDBR DFM 83SLFHDMCK-12HD 85" Clear 780-112HD 661HD SL-11HDCL CFM 85SLFHDMCK-12HD 85" Bronze 780-112HD 661HD SL-11HDBR DFM 85SLFHDMCK-12HD 95" Clear 780-112HD 661HD FM-2000 SL-11HDCL CFM 95SLFHDMCK-12HD 95" Bronze 780-112HD 661HD FM-2000 SL-11HDBR DFM 95SLFHDMCK-12HD 120" Clear 780-112HD 661HD FM-2000 SL-11HDCL CFM120SLFHDMCK-12HD 120" Bronze 780-112HD 661HD FM-2000 SL-11HDBR DFM120SLFHDMCK-14HD 83" Clear 780-111 CFM 83SLIMCK-14HD 83" Bronze 780-111 DFM 83SLIMCK-14HD 85" Clear 780-111 CFM 85SLIMCK-14HD 85" Bronze 780-111 DFM 85SLIMCK-14HD 95" Clear 780-111 CFM 95SLIMCK-14HD 95" Bronze 780-111 DFM 95SLIMCK-14HD 120" Clear 780-111 CFM 120SLIMCK-14HD 120" Bronze 780-111 DFM 120SLIMCK-14HD 79" Clear 780-111HD SL-18HD CFM 79SLIHDMCK-14HD 79" Bronze 780-111HD SL-18HD DFM 79SLIHDMCK-14HD 83" Clear 780-111HD SL-18HD CFM 83SLIHDMCK-14HD 83" Bronze 780-111HD SL-18HD DFM 83SLIHDMCK-14HD 85" Clear 780-111HD SL-18HD CFM 85SLIHDMCK-14HD 85" Bronze 780-111HD SL-18HD DFM 85SLIHDMCK-14HD 95" Clear 780-111HD SL-18HD CFM 95SLIHDMCK-14HD 95" Bronze 780-111HD SL-18HD DFM 95SLIHD MCK-14HD 120" Clear 780-111HD SL-18HD CFM 120SLIHDMCK-14HD 120" Bronze 780-111HD SL-18HD DFM 120SLIHD
McKinney # Roton # Stanley # Markar # Select # Pemko #
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
McKINNEY Hinge CatalogCross ReferenceContinuous Aluminum Geared Hinge
ixAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
Full
Surf
ace
Hal
f Su
rfac
e1 ⁄ 1
6" I
nset
Mou
nt w
ith
Doo
r L
eaf
Lip
Hea
vy D
uty
Hea
vy W
eigh
tSt
anda
rd W
eigh
tH
eavy
Dut
ySt
anda
rd W
eigh
tH
eavy
Dut
ySt
anda
rd W
eigh
tSt
anda
rd W
eigh
t
Roton, Stanley, Markar, Select and Pemco Product Numbers and McKINNEY Equivalent Numbers
McKINNEY # Roton # Stanley # Markar # Select #
MCK-22HD 83" Clear 780-210 SL-21CLMCK-22HD 83" Bronze 780-210 SL-21BRMCK-22HD 85" Clear 780-210 SL-21CLMCK-22HD 85" Bronze 780-210 SL-21BRMCK-22HD 95" Clear 780-210 SL-21CLMCK-22HD 95" Bronze 780-210 SL-21BR
MCK-22HD 120" Clear 780-210 SL-21CLMCK-22HD 120" Bronze 780-210 SL-21BRMCK-22HD 83" Clear 780-210HD FS-2002 SL-21HDCLMCK-22HD 83" Bronze 780-210HD FS-2002 SL-21HDBRMCK-22HD 85" Clear 780-210HD SL-21HDCLMCK-22HD 85" Bronze 780-210HD SL-21HDBR
MCK-22HD 95" Clear 780-210HD FS-2002 SL-21HDCLMCK-22HD 95" Bronze 780-210HD FS-2002 SL-21HDBRMCK-22HD 120" Clear 780-210HD FS-2002 SL-21HDCLMCK-22HD 120" Bronze 780-210HD FS-2002 SL-21HDBRMCK-54HD 83" Clear 780-053 SL-53CLMCK-54HD 83" Bronze 780-053 SL-53BRMCK-54HD 85" Clear 780-053 SL-53CL
MCK-54HD 85" Bronze 780-053 SL-53BRMCK-54HD 95" Clear 780-053 SL-53CL
MCK-54HD 95" Bronze 780-053 SL-53BRMCK-54HD 120" Clear 780-053 SL-53CLMCK-54HD 120" Bronze 780-053 SL-53BRMCK-54HD 83" Clear 780-053HD HS2003 SL-53HDCLMCK-54HD 83" Bronze 780-053HD HS2003 SL-53HDBR
MCK-54HD 85" Clear 780-053HD SL-53HDCLMCK-54HD 85" Bronze 780-053HD SL-53HDBRMCK-54HD 95" Clear 780-053HD HS2003 SL-53HDCLMCK-54HD 95" Bronze 780-053HD HS2003 SL-53HDBRMCK-54HD 120" Clear 780-053HD HS2003 SL-53HDCLMCK-54HD 120" Bronze 780-053HD HS2003 SL-53HDBR
Pemco #
CFS83DFS83CFS85DFS85CFS95DFS95
CFS120DFS120CFS83FDDFS83FDCFS85FDDFS85FD
CFS95FDDFS95FDCFS120FDDFS120FDCHS83DHS83CHS85
DHS85CHS95DHS95CHS120DHS120CHS83HDDHS83HD
CHS85HDDHS85HDCHS95HDDHS95HDCHS120HDDHS120HD
MCK-25HD 83" Clear 780-224 SL-24CLMCK-25HD 83" Bronze 780-224 SL-24BRMCK-25HD 85" Clear 780-224 SL-24CLMCK-25HD 85" Bronze 780-224 SL-24BR
MCK-25HD 95" Clear 780-224 SL-24CLMCK-25HD 95" Bronze 780-224 SL-24BRMCK-25HD 120" Clear 780-224 SL-24CLMCK-25HD 120" Bronze 780-224 SL-24BRMCK-25HD 83" Clear 780-224HD FM-2011 SL-24HDCLMCK-25HD 83" Bronze 780-224HD FM-2011 SL-24HDBR
MCK-25HD 85" Clear 780-224HD SL-24HDCLMCK-25HD 85" Bronze 780-224HD SL-24HDBRMCK-25HD 95" Clear 780-224HD FM-2011 SL-24HDCLMCK-25HD 95" Bronze 780-224HD FM-2011 SL-24HDBRMCK-25HD 120" Clear 780-224HD FM-2011 SL-24HDCLMCK-25HD 120" Bronze 780-224HD FM-2001 SL-24HDBR
CFM 83DFM 83CFM 85DFM 85
CFM 95DFM 95CFM 120DFM 120CFM 83HDDFM 83HD
CFM 85HDDFM 85HDCFM 95HDDFM 95HDCFM 120HDDFM 120HD
MCK-58HD 83" Clear 780-157 SL57AMCK-58HD 83" Bronze 780-157 SL57DMCK-58HD 85" Clear 780-157 SL57AMCK-58HD 85" Bronze 780-157 SL57D
MCK-58HD 95" Clear 780-157 SL57AMCK-58HD 95" Bronze 780-157 SL57DMCK-58HD 83" Clear 780-157HD FS-2002 SL57A-HDMCK-58HD 83" Bronze 780-157HD FS-2002
FS-2002FS-2002
SL57D-HD
MCK-58HD 85" Clear 780-157HD SL57A-HDMCK-58HD 85" Bronze 780-157HD SL57D-HDMCK-58HD 95" Clear 780-157HD FS-2002 SL57A-HDMCK-58HD 95" Bronze 780-157HD FS-2002 SL57D-HD
CFS83CPDFS83CPCFS85CPDFS85CP
CFS95CPDFS95CPCFS83CP HDDFS83CP HD
CFS85CP HDDFS85CP HDCFS95CP HDDFS95CP HD
664664664664664664
664HD664HD664HD664HD664HD664HD
662662662662662662662662
662HD662HD662HD662HD662HD662HD662HD662HD
665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD665HD
663663663663663663663663
663HD663HD663HD663HD663HD663HD663HD663HD
McKINNEY Hinge CatalogComparative Finish Symbols
x An ASSA ABLOY Group company An ASSA ABLOY Group companyAp
ril 2
003
1-800-346-7707www.mckinneyhinge.com
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
ANSI/BHMA Finish Code Base Material
McKINNEY U.S. Description Lawrence Stanley Hager Bommer Steel Brass Bronze Stainless
P USP Primed for Painting P USP USP USP 600
D-4 US1D Dull Black US1D US1D US1B 601
2C US2C Zinc Plated, Commercial US2C US2C US2G 602
3 US3 Bright Brass 3 US3 US3 US3 632 605
4 US4 Dull Brass DB US4 US4 US4 633 606
5 US5 Dull Brass, Oxidized US5 US5 US5 638 609
7 US7 Brass, Nickel OxidizedBright Relieved
US7 US7 636 610
9 US9 Bright Bronze US9 US9 US9 637 611
10 US10 Dull Bronze 10 US10 US10 US10 639 612
10A US10A Antique Bronze, Lacquered 10A US10A US10A US10A10B US10B Antique Bronze, Oiled US10B US10B US10B 640 613
11 US11 Dull Bronze, Oxidized US11 US11 643 616
14 US14 Bright Nickel Plated US14 US14 US14 645 618 618
15 US15 Dull Nickel Plated US15 US15 US15 646 619 619
15A US15A Nickel Oxidized Relieved US15A US15A 647 620 620
17A US17A Half Polished Iron, Smooth US17A US17A US17A 648 621 621
20 US20 Statuary Bronze, Light US20 US20 649 623
20A US20A Statuary Bronze, Dark US20A US20A 650 624
26 US26 Bright Chromium 26 US26 US26 US26 651 625 625
26D US26D Dull Chromium 26D US26D US26D US26D 652 626 62632 US32 Polisehd Stainless Steel US32 US32 US32 629
32D US32D Dull Stainless Steel 32D US32D US32D US32D 630
3C Bright Brass with Clear Powder Coat
4C Dull Brass with Clear Powder Coat
15C Dull Nickel with Clear Powder Coat
AP Aluminum Lacquer LA LS FL2
D-2 CO-Laq, Medium DM L3
D-3 CO-Laq, Dark DD L2 FE3
D-4 CO-Laq, Black L1
GT Grey TonePB Powdered Beige
P-G Powdered Gold
P-W Powdered White DW 13P
Every effort is made by McKINNEY to furnish finishes which do comply with the U.S. Standard, however, we cannotguarantee that our finish will match other manufacturers finish. Where a special finish or a matched finish is required, a sample must be submitted with the order.
xiAn ASSA ABLOY Group company An ASSA ABLOY Group company Ap
ril 2
006
© M
cKIN
NE
YP
rod
ucts
Com
pan
y 20
06
Beveled Edge . . . . . . . . . . . . . . . . . . . . . . . . . .19
Non-Removable Pins . . . . . . . . . . . . . . . . . . . . .7
Raised Barrel . . . . . . . . . . . . . . . . . . . . . . . . . .13
Round Corner . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rust Resistant Base . . . . . . . . . . . . . . . . . . . . .23
Safety Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Prison Safety Feature . . . . . . . . . . . . . . . . . . . . .5
Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73451 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74452 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74453 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74703 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .931001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75-761400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .941414 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .941458 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .941502 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .691552 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .691572 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .713001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .804007-MRB . . . . . . . . . . . . . . . . . . . . . . . . . . . .814007RB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .818007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .829001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7719001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78BP-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83BP-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83BP-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83CS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72CSS-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84DLS-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86DS-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85Edge Guards . . . . . . . . . . . . . . . . . . . . . . . . . .120EP-5J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41FM300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106FS302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112H8007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82HG305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107HG306 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110HG311 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111HG315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108HM304 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109HS1001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79HTA2714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34HTA386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30HTA714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29HTA786 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30ICHTB386 . . . . . . . . . . . . . . . . . .DiscontinuedIHTB386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31IHTB786 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Interim Hinge . . . . . . . . . . . . . . . . . . . . . . . . .98J3001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80MCK-12HD . . . . . . . . . . . . . . . . . . . . . . . . . . .99MCK-14HD . . . . . . . . . . . . . . . . . . . . . . . . . .100MCK-22HD . . . . . . . . . . . . . . . . . . . . . . . . . .102MCK-25HD . . . . . . . . . . . . . . . . . . . . . . . . . .101MCK-54HD . . . . . . . . . . . . . . . . . . . . . . . . . .104MCK-58HD . . . . . . . . . . . . . . . . . . . . . . . . . .103MCK FM300 . . . . . . . . . . . . . . . . . . . . . . . . .106MCK FS302 . . . . . . . . . . . . . . . . . . . . . . . . . .112MCK HG305 . . . . . . . . . . . . . . . . . . . . . . . . .107MCK HG306 . . . . . . . . . . . . . . . . . . . . . . . . .110MCK HG311 . . . . . . . . . . . . . . . . . . . . . . . . .111MCK HG315 . . . . . . . . . . . . . . . . . . . . . . . . .108MCK HM304 . . . . . . . . . . . . . . . . . . . . . . . . .109
MG-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91PH-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92RB-TA2314 . . . . . . . . . . . . . . . . . . . . . . . . . . .96RB-TA2714 . . . . . . . . . . . . . . . . . . . . . . . . . . .96RB-T4A3386 . . . . . . . . . . . . . . . . . . . . . . . . . .96RB-T4A3786 . . . . . . . . . . . . . . . . . . . . . . . . . .96T714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28T2314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33T2714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33T2731 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25T2772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57T2774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47TA314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29TA371 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65TA372 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55TA374 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49TA381 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63TA382 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56TA384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50TA386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30TA391 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43TA392 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44TA393 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29TA771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65TA772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55TA774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49TA781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63TA782 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56TA784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50TA786 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30TA789 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52TA791 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43TA792 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44TA793 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA794 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32TA796 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60TA797 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67TA2314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TA2371 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66TA2372 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58TA2398 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35TA2714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TA2731 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26TA2771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66TA2772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58TA2774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TA2798 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35TA2895 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38TA3331 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26TA3350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27TA3374 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TA3383 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95TA3384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51TA3750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27TA3784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
TA5391 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43TA5392 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44TA5393 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA5394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA5791 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43TA5792 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44TA5793 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA5794 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TCA2314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TCA2714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TCA2771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66TCA2772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58TCA2774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TCA3374 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TCA3381 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64TCA3382 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59TCA3384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51TCA3386 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37TCA3781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64TCA3782 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59TCA3784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51TCA3786 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37T4A3381 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64T4A3382 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59T4A3384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51T4A3386 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37T4A3395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39T4A3781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64T4A3782 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59T4A3784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51T4A3786 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37T4A3789 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53T4A3795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39T4A3796 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61T4A3797 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68T4A4795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39TA4895 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38T6A3386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36T6A3786 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36TCA2371 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66TCA2372 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58TCA4395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
General Information
Index
McKINNEY Products Company • 820 Davis Street • Scranton • PA 18505 • Phone: 800-346-7707 • Fax: 800-541-1073ASSA ABLOY Door Security Solutions – Canada • 6940 Edwards Boulevard • Mississauga, Ontario • Phone: 905-564-5854 • Fax: 905-564-8182
Founded in 1864, McKINNEY Products Company is a market leader in the manufacture of quality architectural gradehinges including security hinges, and continuous hinges for the builders’ hardware industry.
© McKINNEY Products Company 2006
ASSA ABLOY is the world’s leading manufacturer and supplier of locking solutions, meeting tough end-user demands for safety, security and user friendliness.
51101-3/06