Technical Data Sheet.

For professional use only! VR Technical Data Sheet No. 0100/04/2007-GB

Permasolid® Matting Component MA 100

Permasolid® Matting Component MA 100 gives Permasolid® HS Automotive Top Coat Series 275 a matt top coat finish on plastic parts.

1 / 30.10.2007

Substrate.

Suitable substrates: 1)

2) Plastic parts coated with a primer and surfacer

Application.Products: Permasolid® Matting Component MA 100

Permasolid® HS Automotive Top Coat Series 275

Permasolid®VHS Hardener 3225Permasolid®VHS Hardener 3230 slowPermasolid® VHS Hardener 3240 extra slow

Matting Table:

Series 2759080706050

* Depends on the colour, the gloss level of light colours drops more than the gloss level of dark colours when MA 100 is added.

The gloss level is affected by other factors, as well. See table listing parameters affecting the gloss level.

60-90 GE*25-65 GE*

60° angle85-95 GE*80-90 GE*75-90 GE*

50

10

Mixing ratio (% by weight)

Gloss level (GE) according to DIN 67530

For plastic parts, see System Data Sheet "Paint System for Plastic Parts" (VR Technical Data Sheet No. 903.1).

Clean all substrates carefully with Permaloid® Silicone Remover 7010 or Permaloid® Silicone Remover 7799.

Sand lightly.

Substrate pretreatment:

Fully cured, well maintained and lightly sanded original or old finish.

Before further treatment carefully clean substrate with a suitable cleaning agent to remove dust and residues.

203040

MA 100

2 / 30.10.2007

Mixing ratio: Crosslink the matting mixture:

4:1 by volume with

Permasolid®VHS Hardener 3225(for small to medium-sized areas at medium temperatures)

Permasolid®VHS Hardener 3230 slow(for larger areas at medium temperatures)

Permasolid® VHS Hardener 3240 extra slow(for large areas and high temperatures)

See Technical Data SheetPermasolid® VHS Hardeners.

Pot life: Ready for use 60-90 minutes at +20°C.

Reducer: Permacron® Reducer 3364Permacron® Reducer 3380Permacron® Reducer 3365 slowPermacron®Reducer 3385 slow

Spray nozzle*:

Spray pressure*:

Atomising pressure*:

* See manufacturer's instructions!

18-20 seconds

15%

- 0.7 bar

1.3 -1.4 mm

2.0-2.5 bar

2 coats with intermediate flash-off

50 - 60 µm dry film thickness:

Reducer at +20°C material temperature:

Method of application:

Application viscosity 4 mm, +20°C, DIN 53211:

Number of coats:

Recommended film thickness:

-

HVLP

1.3 -1.4 mm

Compliant

3 / 30.10.2007

Special notes. 1

2

3

The material becomes liquid after stirring.

4

5

Factors influencing the degree of gloss:

shorter flash-off time

force drying

longer flash-off time

air drying

hardener with lower solids content

higher application viscosity lower application viscosity

higher dry film thickness lower dry film thickness

slower hardener faster hardener

slower reducer faster reducer

hardener with higher solids content

It is not necessary to add Permasolid® Elastic Additive 9050.

Permasolid® Matting Component MA 100 is not suitable for matting clear coats.

Different hardeners, reducers, methods of application, drying conditions and film thicknesses lead to different degrees of gloss (up to 20%)

Permasolid® Matting Component MA 100 is thixotropic.

The actual gloss level achieved is influenced by various factors aside from the colour.

The following table shows some additional parameters and their effect on the gloss level.

Higher gloss level Lower gloss level

Permasolid® Matting Component MA 100 may influence the hiding power.

4 / 30.10.2007

Drying.

Air drying At +20°C ambient temperature:dust dry: 30-50 minutesdry for assembly: 5-6 hoursdry: overnight

Force drying: Flash-off time: 5-10 minutes

Drying time at +60°C metal temperature:30-40 minutes

Infrared drying: Flash-off time: 5-10 minutes

short wave:5 minutes at 50 % power10 minutes at 100 % power

Data.

Viscosity as supplied:

Flash point:

Solids content:

Specific weight:

VOC content:

*

paste-like

above +23°C

46.0 % by weight31.2 % by volume

The EU limit value for this product (product category IIB.e) in ready to use form is max. 840 g/litre of VOC.

1.13 g/m³

The VOC content of this product in ready to use form is max. 600 g/l.

The coverage was calculated on the basis of the recommended dry film thickness and the solids content by volume (without reducer). No allowance was made for wastage during application.

5 / 30.10.2007

Storage.

6 months in sealed original containers

SPIES HECKER GMBHHorbeller Straße 17D-50858 KölnPhone ++49 (0)2234 - 6019-06Fax ++49 (0)2234 - 6019-4100www.spieshecker.com

Spies Hecker.

Guaranteed shelf life:

A member of DuPont Performance Coatings.

The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved.

We may modify and/or discontinue operation of all or portions of this information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments.

The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose.

The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed.

6 / 30.10.2007