Materials Handling, Rigging, & Cranes
-
Upload
phungduong -
Category
Documents
-
view
225 -
download
3
Transcript of Materials Handling, Rigging, & Cranes
New England
Roofing Industry
Partnership
Materials Handling, Rigging, & Cranes
Training Objectives After completing this unit, you will:
– Know the basic OSHA requirements for the storage and disposal of materials.
– Know hazards in both mechanical and manual material handling.
– Understand hazards of rigging and crane operations and how to minimize them.
– Be aware of proper lifting techniques.
Materials Handling, Rigging & CranesSUBPARTS
1 H,N,O
References 29 CFR 1926.250; Subpart H, Materials
Handling, Storage, Use, and Disposal 29CFR1926.500, Subpart N – Cranes,
Derricks, Hoists, Elevators, and Conveyors
29CFR1926.600, Subpart O – Motor Vehicles, Mechanized Equipment, and Marine Operations
ANSI and ASME Standards
Materials Handling, Rigging & CranesSUBPARTS
2 H,N,O
Materials Handling Dangers Unsafe storage and materials movement can lead to:
– Back injuries (the number one cause of worker compensation claims).
– Struck-by or crushed by falling loads due to rigging failures.
– Electrocutions due to power line contact.– Injury from falling materials.– Injury from slipping, tripping and falling.
Materials Handling, Rigging & CranesSUBPARTS
3 H,N,O
Moving Materials by Hand: Back Facts
8 out of 10 Americans will have a back injury during their life.
Approximately 1 out of 3 injuries at work are back injuries.
Personal pain and inconvenience can not be measured.
Back injuries cost employers an estimated 10 billion dollars each year!
Materials Handling, Rigging & CranesH, N, OSUBPARTS
4
Preventing Back Injuries You can avoid back injuries by:
– Using mechanical aids.– Using proper lifting techniques.– Keeping in lifting shape.– Working as a team when lifting.– Knowing the truth about back belts.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
5
Proper Lifting Technique Basic moves of a proper lift:
– Plan your lift.– Use a wide-balanced stance.– Get close to the load and keep it close to your
body.– Tighten your stomach muscles.– Keep your back straight and use your legs.– Turn with with your feet don’t twist your back.– Avoid lifting above shoulder height.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
6
A Proper Lift
Materials Handling, Rigging & CranesH, N, OSUBPARTS
7
Keeping in Lifting Shape Keeping your stomach and back
muscles strong can help prevent back injuries.
Even if you don’t work out in a gym, you can prevent back injuries.
Strength and flexibility exercises should be done at least every other day.
Materials Handling, Rigging & Cranes 8SUBPART
H,N,O
For Strength and Flexibility
Materials Handling, Rigging & CranesH, N, OSUBPARTS
9
Mechanical Aids Use hand trucks,
dollies, carts, wheel barrows, and wagons whenever possible.
Encourage management to include mechanical aids whenever possible.
Materials Handling, Rigging & CranesSUBPARTS
10 H,N,O
Mechanical AidsMaterials Handling, Rigging & Cranes
SUBPARTS
11 H,N,O
Slab carrying righere has eliminated bending over and has provided securenon-abrasive hand-holds.
Team Lifting
Use team lifting for:– Loads too heavy for one person.– Loads too bulky for one person.– Long loads such as pipes and rolls of
material. Talk to your team-mate! Coordinate your lift!
Materials Handling, Rigging & CranesH, N, OSUBPARTS
12
What About Back Belts? The National Institute for Occupational
Safety and Health (NIOSH) says:– Back belts may not reduce stress on the
back.– May increase blood pressure and heart rate.– May make you think you can lift heavier
loads with a belt on and you could get hurt trying to.
If you want to wear a belt; don’t wear it too tight and don’t lift more than you usually would.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
13
Material Storage Five basic rules for safe storage:
– Keep total weight within the safe loading limits of the building’s floors.
– Keep passageways clear.
– Control materials so they do not slide, fall, or collapse.
– Provide cribbing for heavy loads on unstable surfaces.
– Store materials away from traffic.
Materials Handling, Rigging & CranesH,N, OSUBPARTS
14
What Does OSHA Require? Basic requirements:
– Don’t put materials within 10 feet of roof edge.
– Don’t store materials on scaffolds or runways.
– Keep materials at least 6 feet from floor openings and hoistways.
– Keep aisles clear.– Keep work area free from tripping, fire,
explosion, pest and vegetation hazards.
Materials Handling, Rigging & CranesH,N,OSUBPARTS
15
OSHA Also Requires Specific requirements:
– Stack bagged materials by stepping back the layers and cross-keying the bags at least every 10 bags high.
– Stack bricks no higher than 7 feet.
– Taper masonry blocks back one-half block per tier for stacks above 6 feet.
– Stack lumber on sills and on level solid ground - never exceed 16 feet high and always remove nails!
Materials Handling, Rigging & CranesH,N,OSUBPARTS
16
Setting Materials on the Deck
What could happen to these stacked materials?
Materials Handling, Rigging & CranesH,N,OSUBPARTS
17
Disposal of Waste Material OSHA requirements:
– Scrap lumber, waste and trash must be regularly removed from the work area.
– Burning must meet local regulations.
– Materials dropped more than 20 feet require a chute.
– Solvent waste, oily rags, and flammables must be kept in fire resistant containers until removed.
– If the waste is considered hazardous, your employer will have to follow federal, state, and local regulations.
Materials Handling, Rigging & CranesH,N,OSUBPARTS
18
Debris Chutes
Objectives in using a chute: material control, dust control and protection of workers and bystanders – note the differences here….
Materials Handling, Rigging & CranesH ,N, OSUBPARTS
19
Mechanical Materials Handling Depending on the job, you might use
or work around:– Buggies– Roof Hoists– Conveyors– Skid-steers (“Bobcats”)– Rough Terrain Forklifts (“Lulls”) – Cranes
Materials Handling, Rigging & CranesH, N, OSUBPARTS
20
Buggies
What are the safety concerns while moving materials with these?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
21
Mechanical Equipment on Flat Roofs Will the deck support the weight of the
equipment? Has the equipment been inspected? Are all equipment guards in place? Is the operator trained?
– See Subpart C - .20(b)(4) Are all aware that the equipment is not to be
operated outside warning lines due to the fall hazard? – See Subpart M - Fall Protection -.502– Closest approach is 6 feet parallel and 10 feet
perpendicular to direction of travel.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
22
Roof Hoists
What are the manufacturer’sinstructions for set up & use?
What does OSHA say?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
23
Roof Hoist Safety Concerns .552(a)(1) Compliance with manufacturer’s
specifications and limitations. .552(a)(2) Load capacity, hazard warnings and
instructions must be posted. .552(a)(3)(i-iv) Wire rope replacement criteria. .552(a)(4) Hoist rope is to be installed in
accordance with manufacturer’s instructions. .501(b)(3) Fall Protection (Subpart M) in hoist area.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
24
Is the Hoist Operator Protected?Materials Handling, Rigging & CranesH, N, O
SUBPARTS
25
Using Conveyors to Move MaterialsMaterials Handling, Rigging & CranesH, N, O
SUBPARTS
26
Safety Concerns In Conveyor Use Set up and used in accordance with the
manufacturer’s instructions?
Guards in place on pinch points?
Power line clearances maintained?
Maintenance program in place?
Materials Handling, Rigging & CranesH, N, O 27SUBPART
Safety Concerns In Conveyor Use No riders on conveyor!
.555(a) Means for stopping motor at operator’s station and start up warning.
.555(a)(5) Protection for workers below against falling objects.
.555(a)(7) Lockout/Tagout for maintenance.
Materials Handling, Rigging & CranesH, N, O 28SUBPART
Using Conveyors to Move MaterialsMaterials Handling, Rigging & CranesH, N, O 29
Power line clearance?
Back up alarm orsignal person?
Fall protection for roof workers?
SUBPART
Using Skid Steers If on the roof – will it take the load? Is the operator qualified?
– .20(b)(4) – Again! Training is available from some manufacturers.
– Skid Steers are powerful, work in close quarters with people and are very quick, with large areas where the operator cannot see (the “no-zone”).
Is the work area adequately barricaded?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
30
Skid Steer Loader
What do weneed to know about this operator?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
31
Eye level 5 ft - 5 in above ground level
6’ 1”
11’ 7”
6’ 3”
Operator sight distancesfrom eye level to ground
Vehicle:S-44 Bobcat
3’ 1”
4’ 10”
11’ 5”
21’ 8”
The “NO-ZONE”
Materials Handling, Rigging & CranesH, N, O 32SUBPARTS
Using Forklifts to Move Materials What do we need to know?
– Is the operator trained?• See .602(d)
– Has the machine been inspected and properly maintained?
– Is the backup alarm audible?– Are ground personnel protected?– Is the balanced load within capacity?– Are workers on roof protected from falls?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
33
Getting Materials to the Roof
How can we protect against falls in these situations?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
34
Using Forklifts
What precautions need to be taken around the machine’s operating area?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
35
Eye level 7 ft - 3 in aboveground level
39’ 0”
21’ 2”
Operator sight distancesfrom eye level to ground
Vehicle: R-14793 High Reach Fork Lift
10’ 9”7’ 9”
3’ 0”
85’ 0”
14’ 10”
18’ 2”
The “NO-Zone”
N, OTS
Materials Handling, Rigging & CranesSUBPARTS
H, N, O 36
Platforms on Forklifts If you work off of some attachment it must:
(1) Be secured to forks. (2) Have a guardrail.
(3) Have a Personal Fall Arrest System tie-off.
(4) Used only while the operator is in the seat.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
37
Rigging and Crane Safety
Rigging is the lines or cables used to lift and move materials by hoisting with a crane.
A rigger is a skilled mechanic who prepares heavy equipment or loads of material for movement.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
38
Examples of Rigging
Materials Handling, Rigging & CranesH, N, OSUBPARTS
39
The Hazards of Rigging
Possible contact with power lines. Rigging failures due to overloaded,
improper, or defective rigging. Out of control loads. Being struck by the crane’s swing
radius.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
40
Can Anyone Rig or Lift Loads?
Rigging must be done under the supervision of a Competent Person.
The crane operator must be highly qualified and certified.
Improper rigging or unqualified operators can be deadly!
Materials Handling, Rigging & CranesH, N, OSUBPARTS
41
The Rigger’s Duties
The rigger selects the rigging.
The rigger sets-up the rigging.
The rigger directs the lift.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
42
OSHA Rigging Requirements All slings and hardware must be manufactured
to meet demanding specifications which include safety factors.
All web or alloy chain slings must be clearly stamped, marked, or labeled, for capacity.
OSHA prohibits job made: slings, hooks, links, and fasteners formed from bolts.
Before each use all components must be inspected by a Competent Person.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
43
Safe Working Load (SWL) The maximum load allowed on rigging is
the Safe Working Load (SWL). The sling may actually be able to hold 5
times the SWL. A safety factor is the ratio of the ultimate
strength to the SWL. If a rigger exceeds the SWL, then they lose
some of the safety factor.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
44
Knowing Safe Working LoadsMaterials Handling, Rigging & CranesH, N, O
SUBPARTS
45
Sling Angle The safest sling angles are greater than 450 from the horizontal.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
46
Rigging the Load
Balanced load; sling angle >600
Sling angles <450, loadunstable, worker notprotected.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
47
Working Safely Around Rigging General safety practices:
– Keep at least ten feet away from power lines up to 50 kV.
– Increase power line clearance distance by .4” per kV >50kV
– Never hoist loads over workers.– Never stand too close or under a load.– Never ride a load.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
48
Working Safely Around Rigging2
General safety practices:– Use tag lines to control loads while
lifting.– Test lift the rigging.– Use proper equipment, make sure it is
marked, not home-made, and in good shape.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
49
Crane Hand Signals
Only a qualified rigger will give hand signals.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
50
Basic Crane Safety Do we have the right crane for the job? Is the operator qualified on that crane? Has the crane been inspected? Is the crane set up on solid ground?
– Full outriggers with cribbing?– Level, with tires off the ground?
Are power line clearances known? Do we know the weight of the load? Is everyone aware that a lift is being
made?
Materials Handling, Rigging & CranesH, N, OSUBPARTS
51
Basic Crane Safety2
Is the load properly rigged for a stable, vertical lift?
Is there a high wind condition? Is the swing radius barricaded? Can a tagline be properly used? Can the crane make the lift and set
the load without interference?
Materials Handling, Rigging & Cranes H, N, OSUBPARTS
52
Truck-Mounted Cranes/Boom Trucks
Materials Handling, Rigging & CranesH, N, OSUBPARTS
53
Case Study: What went wrong?Two employees were moving structural steel building beams to a storage area. After setting the fourth beam on the crib, the signal man signaled the crane operator to pull the sling from around a cribbed structural beam which was set on its flange side. The second employee then attempted to remove the shackle from the beam when the swaged fitting of the sling apparently caught and caused the steel beam to roll off the cribbing, crushing the second employee.
Materials Handling, Rigging & CranesH, N, OSUBPARTS
54
Materials Handling(1926.250 - 252)
Common OSHA Citations:.251(a)(1) Rigging equipment inspection
and removal from service..251(e)(8) Synthetic Web Slings – removal from service..252(a) Exterior drop chutes.251(a)(4) Rigging capacity not marked – not proof-
tested.
How can the hazards addressed by these Standards best be corrected, controlled, or eliminated?
SUBPARTS
H, N,O Materials Handling, Rigging & Cranes 55
Review Questions True or False?
1. Back injuries are the number one cause of worker compensation claims.
2. Using proper lifting techniques, staying in shape, using mechanical aids, and team lifting are the best ways to avoid back injuries.
3. Using a back belt almost always prevents a back injury.
4. Anyone can hook-up a sling and be a rigger.
Materials Handling, Rigging & Cranes H, N, OSUBPARTS
56
Review Questions True or False?
5.Job-made slings, hooks, links, and fasteners formed from bolts are allowed if a Competent Person says so.
6.Proper knots are permitted in web-slings.7.Slings should be inspected before each use
and pulled from service if found defective. 8.The safest sling angles are less than 45
degrees from the horizontal.
Materials Handling, Rigging & Cranes H, N, OSUBPARTS
57
Review Questions True or False?
9. Cranes and rigging must stay at least 10 feet from power lines.
10. Materials can be stored within 10 feet of the roof’s edge.
11. Materials dropped more than 20 feet require a chute.
12. Materials must be kept at least 2 feet from floor openings and hoistways.
Materials Handling, Rigging & Cranes H, N, OSUBPARTS
58