Materials Handling · Duty Rating Single Speed - 60% ED (60 min) Dual Speed - 40/20% ED (30/10min)...
Transcript of Materials Handling · Duty Rating Single Speed - 60% ED (60 min) Dual Speed - 40/20% ED (30/10min)...
HandlingMaterials
EDITION 2015
Power Hoisting Designed To Lift Your Work Rate
Materials Handling
01
» Hoist ..................................................................... 03
» Chain Blocks ..................................................... 80
» Lever hoist ......................................................... 93
» Trolley .................................................................. 106
» Clamps ................................................................ 126
» Magnetic Lifter .................................................. 152
» Load Skate ......................................................... 156
» Spring Balances ............................................... 158
» Drum Clamp ...................................................... 165
1800 067 687
3“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Care & Safety Instructions forPower Hoists and Trolleys
Safety
Before Use
While in Operation
Danger exists when heavy loads are transported, particularly when the equipment is not being used correctly or is poorly maintained. Because accidents and serious injury could result, special safety precautions apply to the operation, maintenance and inspection of PWB Anchor power hoist products.
• Always read the owner’s manual and safety instructions.• Never lift more than the capacity shown on the hoist name plate.• Always check that the hook latches work properly.• Never operate a hoist if damaged or malfunctioning.• Never use a twisted, kinked, damaged or stretched load chain.• Never use a hoist if the hook latch is missing or broken.• Never use a hoist without a hoist name plate.• Never use a hoist with a modified or deformed hook.
• Never use a hoist for lifting, supporting or transporting people.• Never lift or transport loads over or near people.• Never support a load on the tip of the hook.• Always make sure that the load is properly seated in the hook.• Never use the hoist chain as a sling.• Never swing a suspended load.
WARNINGIMPROPER chain hoist use could result in death or serious injury
42015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Electric Hoists & TrolleysKey features of the Kito ER2 Electric Chain Hoist
1800 067 687
5“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Key features of the Kito ER2 Electric Chain Hoist Electric Hoists & Trolleys
ER2 Series Electric Chain Hoist
(415v - 50Hz) - 3 Phase
Rated Capacity Single Speed - 125kg to 20 tonne Dual Speed - 125kg to 20 tonne
Voltage 380-415 V 50Hz
Duty Rating Single Speed - 60% ED (60 min) Dual Speed - 40/20% ED (30/10min)
Classifications ISO Heavy Duty classification M4 & M5 FEM (Europe) 1Am & 2m ratingASME HST (USA) H4 Duty Class
Enclosure Hoist body - IP55 (dust proof and water jet protected) Push button control - IP65 with emergency stop
Suspension varieties Hook, manual trolley, motorized trolley
Operating Temperature
-20 to 40 degress
Operating Humidity 85% RH or less
62015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
CapacityPart No. (3 Metre)
Part No. (6 Metre)
ModelLifting Speed m/min
Motor Rating output KW
Motor Rating (%ED)
Load ChainDia (mm) x fall
Hook SuspendedHeadroom
(mm)
Hook Suspended Weight (kg)
Load ChainDia x Pitch
(mm)
Load Chain
Part No.
Single Speed
250kg 45801 45961 ER2-003S 9.1 0.56 60 4.3 x 1 350 27 4.3 x 12.0 45951
500kg 45802 45962 ER2-005L 3.8 0.56 60 6.0 x 1 370 33 6.0 x 16.7 45952
500kg 45803 45963 ER2-005S 7.3 0.9 60 6.0 x 1 370 37 6.0 x 16.7 45952
1 tonne 45804 45964 ER2-010L 3.5 0.9 60 7.7 x 1 430 47 7.7 x 21.4 45953
1 tonne 45805 45965 ER2-010S 7.1 1.8 60 7.7 x 1 430 54 7.7 x 21.4 45953
1.5 tonne 45806 64121 ER2-015S 4.5 1.8 60 10.2 x 1 510 72 10.2 x 28.4 45954
2 tonne 45807 45966 ER2-020L 3.7 1.8 60 10.2 x 1 575 73 10.2 x 28.4 45954
2 tonne 45808 63453 ER2-020S 7.0 3.5 60 10.2 x 1 590 91 10.2 x 28.4 45954
2.5 tonne 45809 63550 ER2-025S 5.7 3.5 60 11.2 x 1 625 104 11.2 x 31.2 45955
3 tonne 45810 63130 ER2-030S 4.4 3.5 60 10.2 x 2 785 107 10.2 x 28.4 45954
5 tonne 45811 62866 ER2-050S 2.9 3.5 60 11.2 x 2 850 132 11.2 x 31.2 45955
Dual Speed with Inverter
250kg 45821 - ER2-003IS 10.8-1.8 0.56 40 / 20 4.3 x 1 350 27 4.3 x 12.0 45951
500kg 45822 - ER2-005IL 4.5 - 0.8 0.56 40 / 20 6.0 x 1 370 32 6.0 x 16.7 45952
500kg 45823 - ER2-005IS 8.5 - 1.4 0.9 40 / 20 6.0 x 1 370 36 6.0 x 16.7 45952
1 tonne 45824 - ER2-010IL 4.2 - 0.7 0.9 40 / 20 7.7 x 1 430 45 7.7 x 21.4 45953
1 tonne 45825 - ER2-010IS 8.2 - 1.4 1.8 40 / 20 7.7 x 1 430 52 7.7 x 21.4 45953
1.5 tonne 45826 - ER2-015IS 5.3 - 0.9 1.8 40 / 20 10.2 x 1 510 72 10.2 x 28.4 45954
2 tonne 45827 - ER2-020IL 4.3 - 0.7 1.8 40 / 20 10.2 x 1 575 73 10.2 x 28.4 45954
2 tonne 45828 - ER2-020IS 8.2 - 1.4 3.5 40 / 20 10.2 x 1 590 89 10.2 x 28.4 45954
2.5 tonne 45829 - ER2-025IS 6.6 - 1.1 3.5 40 / 20 11.2 x 1 625 100 11.2 x 31.2 45955
3 tonne 45830 - ER2-030IS 5.2 - 0.9 3.5 40 / 20 10.2 x 2 785 105 10.2 x 28.4 45954
5 tonne 45831 - ER2-050IS 3.3 - 0.6 3.5 40 / 20 11.2 x 2 850 128h 11.2 x 31.2 45955
1800 067 687
7“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Electric Hoists & Trolleys
ER2 Series Electric Chain Hoist (415v - 50Hz) - 3 Phase
» Standard features include:
• Five metres of power supply cable as standard.
• Optional length of lift, pendant cable and power supply cable other than standard available on request.
• Steel chain containers are available as an option if your lift is more than capacity of the standard container volume.
• Patented Friction Clutch allows for reliable overload protection and safety.
• Thermal Protection on Hoist Motor reduces risk of motor burnout.
• Upper/Lower Limit Switch.
• Adjustment free brakes - less maintenance.
• Nickel plated load chain - Added Resistance to rust and abrasion.
• Fan Cooled motor - reduces overheating.
• Condition Monitoring with Counter/Hour Meter - Built in.
The PWB Anchor ER2 Electric Chain Hoist manufactured by KITO is environmentally friendly with its new compact, lightweight and energy efficient design. Offering thermal protection to prevent overheating, upper and lower limit switches, CH (Counter/Hour) meter and variable speed inverter as standard equipment (Inverters installed on 2 speed models only).Available in capacities ranging from 250kg to 20 tonnes in optional lift heights.
Coupled with the new MR2 Motorised Trolley, the ER2/MR2 combination allows for easier and accurate load positioning in the work place.
• Applications: Mining, construction, engineering, entertainment
• Australian Standard: AS1418.2
82015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Capacity (kg)
ModelPart No. (3 metre)
Part No. (6 metre)
D (mm)
a (mm)
b (mm)
d (mm)
e(mm)
f (mm)
g (mm)
h (mm)
i(mm)
ER2 Dimensions
250 ER2-003S 45801 45961 430 478 321 219 259 260 27 99 93
250 ER2-003IS 45821 - 430 535 345 276 259 284 27 99 117
500 ER2-005L 45802 45962 490 513 348 242 271 283 27 113 106
500 ER2-005IL 45822 - 490 571 348 300 271 283 27 113 106
500 ER2-005S 45803 45963 490 510 348 242 268 283 27 113 106
500 ER2-005IS 45823 - 490 568 348 300 268 283 27 113 106
1000 ER2-010L 45804 45964 550 589 376 291 298 335 31 129 118
1000 ER2-010IL 45824 - 550 614 376 316 298 335 31 129 118
1000 ER2-010S 45805 45965 550 598 376 219 307 335 31 129 118
1000 ER2-010IS 45825 - 550 623 376 316 307 335 31 129 118
1500 ER2-015S 45806 64121 630 646 427 308 338 385 34 161 138
1500 ER2-015IS 45826 - 630 710 427 372 338 384.5 34 160.5 137.5
2000 ER2-020L 45807 45966 630 646 427 308 338 385 39 161 138
2000 ER2-020IL 45827 - 630 710 710 427 338 384.5 39 160.5 137.5
2000 ER2-020S 45808 63453 630 703 427 347 356 385 39 161 138
2000 ER2-020IS 45828 - 630 767 427 411 356 384.5 39 160.5 137.5
2500 ER2-025S 45809 63550 840 736 445 337 399 438 39 174 143
2500 ER2-025IS 45829 - 840 800 445 401 399 437.5 39 173.5 142.5
3000 ER2-030S 45810 63130 920 703 427 347 356 397 44 216 82
3000 ER2-030IS 45830 - 920 767 427 411 356 397 44 216 82
5000 ER2-050S 45811 62866 920 736 445 337 399 439 47 232 85
5000 ER2-050IS 45831 - 920 800 445 401 399 439 47 231.5 84.5
1800 067 687
9“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Electric Hoists & Trolleys
MR2 Electric Motorised Trolley
» Standard features include:
• Bearings built in side rollers provide smooth running through the minimum radius curve and excellent traversing performance and assist with derailment prevention.
• Simple gear box construction.
• Improved balance due to a lighter weight geared
motor.
• Semi tapered flange wheels - allows use on most monorail beams.
• Speed variations; single low speed, single standard
speed, and dual speed - high and low.
• Motor has a pull rotor brake for accurate and safe stopping.
• 10 metre power supply cable as standard.
• 10 m/min traverse speed available on request.
• Applications: Mining, construction, engineering, entertainment
• Australian Standard: AS1418.2
102015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Part No. Model Capacity (kg)Traverse
Speed M/MinBeam Range
(mm)Min Radius
(Mtr)
Single speed standard flange width
45901 MR2-010S 1000 20 58 - 153 Flg 0.8
45902 MR2-020S 2000 20 82 - 178 Flg 0.8
45903 MR2-030S 3000 20 82 - 178 Flg 1.0
45904 MR2-050S 5000 20 100 - 178 Flg 1.8
Dual speed standard flange width
45921 MR2-01IS 1000 24 / 4 58 - 153 Flg 0.8
45922 MR2-02IS 2000 24 / 4 82 - 178 Flg 0.8
45924 MR2-03IS 3000 24 / 4 82 - 178 Flg 1.0
45925 MR2-05IS 5000 24 / 4 100 - 178 Flg 1.8
Single speed wide flange
45911 MR2-010SW 1000 20 154- 305 Flg 0.8
45912 MR2-020SW 2000 20 179- 305 Flg 0.8
45913 MR2-030SW 3000 20 179- 305 Flg 1.0
45914 MR2-050SW 5000 20 179- 305 Flg 1.8
Dual speed wide flange
45931 MR2-010ISW 1000 24 / 4 154- 305 Flg 0.8
45932 MR2-020ISW 2000 24 / 4 179- 305 Flg 0.8
45933 MR2-030ISW 3000 24 / 4 179- 305 Flg 1.0
45935 MR2-050ISW 5000 24 / 4 179- 305 Flg 1.8
1800 067 687
11“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Electric Hoists & TrolleysKey features of the Kito EQ Electric Chain Hoist
122015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
» EQ Electric Chain Hoist - Dual Speed with Inverter
Standard features include:
• Adjustable speed inverter. • Counter hour meter.
• IP55 dust and water jet proof body. • 40/20% duty rating.
• No load, high speed feature. • Standard 3m and 6m lifts.
• Applications: Mining, construction, engineering, entertainment and manufacturing.
• Australian Standard: AS1418.2
Capacity Part No. ModelStandard
Lift (m)
Lift Speed
(m / min)
Headroom
(mm)
Load Chain dia
(mm) x falls
Weight
(kg)
125 kg 47106 EQ001IS 3 17 - 2.8 395 5.6 x 1 30
250 kg 47107 EQ003IS 3 10 - 1.7 395 5.6 x 1 30
500 kg 47108 EQ005IS 3 7.6 - 1.3 410 5.6 x 1 32
1000 kg 47109 EQ010IS 3 7.1 - 1.2 465 7.1 x 1 42
125 kg 47190 EQ001IS 6 17 - 2.8 395 5.6 x 1 32
250 kg 47191 EQ003IS 6 10 - 1.7 395 5.6 x 1 32
500 kg 47192 EQ005IS 6 7.6 - 1.3 410 5.6 x 1 34
1000 kg 47193 EQ010IS 6 7.1 - 1.2 465 7.1 x 1 46
1800 067 687
13“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
» MR2Q Electric Motorised Trolley
Standard features include:
• Side rollers with in-built bearings provide smooth running through the minimum radius curve and excellent traversing performance with derailment prevention. • Simple gear box construction.
• Improved balance due to a lighter weight geared motor. • Speed variations.
• No load, high speed feature. • Dual Speed, standard and wide beam flange width.
• Applications: Mining, construction, engineering and manufacturing.
Capacity Part No. ModelTraverse Speed
M / Min
Bean Range
(mm)Min Radius Mtr
125 kg 47162 MR2Q001IS 24 / 4 58 - 153 0.8
250 kg 47163 MR2Q003IS 24 / 4 58 - 153 0.8
500 kg 47164 MR2Q005IS 24 / 4 58 - 153 0.8
1000 kg 47160 MR2Q010IS 24 / 4 58 - 153 0.8
125 kg 47167 MR2Q001IS 24 / 4 154 - 305 0.8
250 kg 47168 MR2Q003IS 24 / 4 154 - 305 0.8
500 kg 47170 MR2Q005IS 24 / 4 154 - 305 0.8
1000 kg 47165 MR2Q010IS 24 / 4 154 - 305 0.8
142015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Electric Hoists & Trolleys
EQ Electric Chain Hoist Series (415v - 50Hz) - 3 Phase
The new EQ Series Electric Chain Hoist from Kito is economical, lightweight and compact. It incorporates the quality and safety features expected of a Kito hoist.
Available in standard 3 and 6 metre lifts only.
Rated Capacity 125kg - 1 tonne (Dual Speed)
Voltage 380-440V 50/60Hz/3 Phase
Duty Rating 40/20%
Motor Insulation Class B
Enclosure Hoist body: IP55Push button control IP65 with emergency stop
Suspension Varieties Suspension Eye, Adapted motorized trolley available on request
Operating Temperature -200 to 400 celsius
Operating Humidity 85% RH or less
Suitable Industries Mining, Construction, Engineering, Entertainment and Manufacturing
Australian Standard AS1418.2
1800 067 687
15“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Capacity ModelPart No. (3 metre)
Part No. (6 metre)
D (mm) a (mm)
EQ Dimensions
125 kg EQ001IS 47106 47190 485 417
250 kg EQ003IS 47107 47191 485 417
500 kg EQ005IS 47108 47192 485 417
1000 kg EQ010IS 47109 47193 535 433
b (mm) d (mm) e (mm) f (mm) g (mm) h (mm) i (mm)
EQ Dimensions
367 230 187 298 27 137 128
367 230 187 298 27 137 128
367 230 187 298 27 137 128
403 245 188 332 31 154 142
» EDL Series Electric Chain Hoist (240v - 50Hz)
This compact single phase Electric Hoist available in Single or Dual Speed, is ideal for lifting small loads that are too heavy to be handled manually. The EDL range of single phase hoists from KITO feature heavy duty motors with automatic load brake and overload clutch, an IP54 rated lightweight compact aluminium body.
Standard features include:
• 30% ED Rating.
• Patented ‘Friction Clutch’ allows for reliable overload protection and safety.
• Upper Limit Switch.
• Motor has high performance mechanical brake for safe stopping.
• Nickel plated load chain allows for added resistance to rust and wear.
162015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Rated Capacity 100kg to 480kg
Voltage 240V 50Hz
Control Voltage Low voltage control is standard
Motor Insulation Class F
Enclosure Single speed/ Dual speed - IP54 (dust proof and water protected) Cylinder - IP44IP65 Pendant with emergency stop
Suspension Varieties Hook, mini trolley, universal trolley, manual trolley
Operating Temperature -200 to 400 celsius
Operating Humidity 85% RH or less
• Applications: Mining, construction, engineering
• Australian Standard: Complies to AS1418.2
Model a (mm) d (mm) e (mm) f (mm) h (mm) i (mm) g (mm) j (mm) k (mm) m (mm) n (mm)
EQ Dimensions
EDL10S 371 187 184 205 125 80 25 25 340 92 73
EDL18S 371 187 184 205 125 80 25 25 340 92 73
EDL16S 428 205 223 219 135 84 25 25 362 92 73
EDL24S 428 205 223 219 135 84 25 25 362 92 73
EDL06ST 371 187 184 205 125 80 25 25 340 92 73
EDL10ST 371 187 184 205 125 80 25 25 340 92 73
EDL18ST 371 187 184 205 125 80 25 25 340 92 73
EDL16ST 428 205 223 219 135 84 25 25 362 92 73
EDL24ST 428 205 223 219 135 84 25 25 362 92 73
EDCL10SD 371 187 184 205 125 80 25 25 340 92 73
EDCL18SD 371 187 184 205 125 80 25 25 340 92 73
EDCL16SD 428 205 223 219 135 84 25 25 362 92 73
1800 067 687
17“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
» EDL Single Speed - Pendant Control
» EDL Dual Speed - Pendant Control
» EDCL Dual Speed - Cylinder Control
CapacityPart
No.Model
Standard
Lift
Lift Speed
(m / min)
Headroom
(mm)
Load Chain
dia (mm) x
falls
Weight
(kg)
Load Chain
Dia x Pitch
(mm)
Load
Chain
Part No.
100 kg 45398 EDL10S 3.0 13.0 315 4.0 x 1 12 4.0 x 12.0 48351
160 kg 48347 EDL16S 3.0 20.0 330 4.0 x 1 16 4.0 x 12.0 48351
180 kg 45399 EDL18S 3.0 8.0 315 4.0 x 1 12 4.0 x 12.0 48351
240kg 48348 EDL24S 3.0 13.5 330 4.0 x 1 16 4.0 x 12.0 48351
480 kg 62445 EDL48S 3.0 6.7 520 4.0 x 2 21.5 4.0 x 12.0 48351
CapacityPart
No.Model
Standard
Lift
Lift Speed
(m / min)
Headroom
(mm)
Load Chain
dia (mm) x
falls
Weight
(kg)
Load Chain
Dia x Pitch
(mm)
Load
Chain
Part No.
100 kg 45400 EDL10ST 3.0 13.0 /3.0 315 4.0 x 1 12.5 4.0 x 12.0 48351
160 kg 44282 EDL16ST 3.0 20.0 / 5.0 330 4.0 x 1 16.5 4.0 x 12.0 48351
180 kg 45401 EDL18ST 3.0 8.0 / 3.0 315 4.0 x 1 12.5 4.0 x 12.0 48351
240kg 48349 EDL24ST 3.0 13.5 / 3.0 330 4.1 x 1 16.5 4.0 x 12.0 48351
480 kg 61866 EDL48ST 3.0 6.7 / 2.0 520 4.0 x 2 21.5 4.0 x 12.0 48351
CapacityPart
No.Model
Standard
Lift
Lift Speed
(m / min)
Headroom
(mm)
Load Chain
dia (mm) x
falls
Weight
(kg)
Load Chain
Dia x Pitch
(mm)
Load
Chain
Part No.
100 kg 45402 EDCL10SD 1.8 20.0 /4.0 960 4.0 x 1 15 4.0 x 12.0 48351
240 kg 44209 EDCL24SD 1.8 13.5 / 3.0 960 4.0 x 1 19 4.0 x 12.0 48351
182015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Rated Capacity Single phase hoist: 500 to 1000kg
Voltage 240V 10amp power supply
Control voltage 24V
Motor insulation Class B
Enclosure IP54 (dust proof and water protected)IP65 Pendant with emergency stop
Suspension varieties Hook/Trolley
Operating Temperature
-20 to 40 degress
Operating Humidity 85% RH or less
The EF/SHL range of heavy duty single phase electric hoists are light and compact units with aluminium die-cast bodies that are available in 500kg and 1 tonne capacities.
Standard features include:
• Exclusive pull-rotor type motor braking system provides high braking capability for the most sure way to stop the load at the desired position.
• Totally enclosed exclusive pull rotor type motor permits ideal operation of hoists.
• KITO’s friction clutch, which prevents from overloading, allows the motor to run free at the highest and lowest hook positions.
• Aluminium die-cast hoist body provides lighter weight, compactness, high mobility and rapid heat dissipation.
» EF Electric Chain Hoist
1800 067 687
19“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
• Totally enclosed weather-resistant construction makes it ideal for use in humid atmospheres.
• Case hardened chain.
• Highly insulated push button station.
• Drop-forged heat treated hook does not fracture but opens slowly when excessively overloaded.
• Emergency stop device available on request.
• Applications: Mining, construction, engineering
• Australian Standard: Complies to AS1418.2
CapacityPart No. 3
MetreModel
Lift Speed
(m / min)
Load Chain dia
(mm) x falls
Headroom
(mm)
Weight
(kg)
Load Chain Dia x
Pitch (mm)
Load Chain
Part No.
500 kg 45586 EF / SHL005S 3.5 6.3 X 1 560 45 6.3 X 19 43206
1 Tonne 45587 EF / SHL010S 1.8 6.3 X 2 635 50 6.3 X 19 43206
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
202015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Hitachi Electric Chains Hoists
Hitachi’s reputation for excellence in design, quality, reliability and performance has made this brand a global market leader. With over three decades of proven reliability throughout Australasia and an extensive operating range, Hitachi Electric Chain Hoists are suited to most applications. The Hitachi models vary from 250kg to 15 tonne capacity and are available in three or single phase, two speed or single speed while being tested to the Australian standards.
Features
• All Hitachi models are manufactured to comply with AS1418.2.
• Operation: fully contactorised with high rated contactors and pendant controls; both fitted with mechanical interlocks and 24 Volt control.
• Optional IP65 pendant including E-Stop available.
• Safety Limits: full current and shunt limit switches operate in both directions of hook travel.
• Overload Limiter: this electro-mechanical device is exclusive to the Hitachi range and boasts a far more superior overload protection device than the slipping clutch method. Available on all Hitachi models.
• Braking: all models are fitted with an electro-magnetic, self-adjusting disc type brake to the gearbox and the “F” models have an additional auxiliary centrifugal brake fitted to the motor.
• Chain Bucket: noiseless design with flexible mounting.
• High quality Grade 80 zinc plated load chain supplied as
standard.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
21“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists• IP54 protection rating on all electric hoists and trolleys.
• Motor thermal protection on all Hitachi models.
• Optional radio remote control.
• Ambient temperature requirement of -10 to 40 degrees.
• Class M4 inclusive of 180 starts per hour.
• Completely enclosed design. Entire mechanism including; the motor, dual brake system, gears, rotating parts and electrical system can be operated under severe conditions.
• Reverse phase protection relay on all models excluding; 250kg, 500kg and all single phase models.
• Special low headroom hoist and trolley arrangements available to suit tight headroom applications.
• Electric trolleys are fitted with Guide Rollers as standard to reduce wear and ensure suitability for curved beam.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
222015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Specifications
THREE PHASE / SINGLE SPEED HOISTS - 415 Volt, 50 Hz
Model 1/4S 1/2S 1S 2S 1F 2F 3F 5F
Stock Code HEH010 HEH050 HEH100 HEH200 HEH0110 HEH210 HEH300 HEH500
Rated Capacity (kg) 250 500 1000 2000 1000 2000 3000 5000
Speed (m/min) 10 7.2 4.6 2.3 7.1 6.8 4.1 2.8
Motor (kW) 0.45 0.63 0.8 1.3 1.3 2.4 2.4 2.4
Weight (kg) 28 31 37 49 42 80 99 121
Headroom (mm) 450 450 530 645 535 660 820 1020
Model 1/4SN 1/2SN 1SN 2SN 2FN 3FN 5FN
Stock Code HEH020 HEH060 HEH120 HEH220 HEH230 HEH330 HEH530
Rated Capacity (kg) 250 500 1000 2000 2000 3000 5000
Speed (m/min) 7.2 / 1/8 7.2 / 1.8 4.6 / 4.2 2.3 / 0.6 6.8 / 1.7 4.0 / 1.0 2.8 / 0.7
Motor (kW) 0.32 / 0.08 0.63 / 0.16 0.8 / 0.2 0.8 / 0.2 2.4 / 0.6 2.4 / 0.6 2.4 / 0.6
Weight (kg) 33 36 42 54 96 112 146
Headroom (mm) 450 450 530 645 660 820 1020
THREE PHASE / TWO SPEED HOISTS - 415 Volt, 50 Hz
Model 1/4S1 1/2S1 1S1 2S1
Stock Code HEH900 HEH907 HEH911 HEH920
Rated Capacity (kg) 250 500 1000 2000
Speed (m/min) 5 3.6 2.3 1.1
Motor (kW) 0.25 0.32 0.4 0.4
Weight (kg) 34 34 39 51
Headroom (mm) 450 450 530 645
SINGLE PHASE / SINGLE SPEED HOISTS - 240 Volt, 50 Hz
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
23“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists
Model 1ET 2ET 3ET 5ET
Stock Code HET100 HET200 HET300 HET500
Rated Capacity (kg) 1000 2000 3000 5000
ET Speed (m / min) Single Speed ET 10.5 or 21.0
ETN Speed (m / min) Two Speed ETN 21.0 / 5.3
Motor (kW) 0.14 0.14 0.3 0.3
Weight (kg) 38 52 60 86
Min, Radius (m) 1.5 1.8 2.0 3.0
Girder Width (mm)* 75 - 125 100 - 150 100 - 150 125 - 175
THREE PHASE / ELECTRIC TROLLEYS - 415Volt, 50Hz
* Larger girder widths are available upon request.
Dimensions (in mm)
HITACHI S SERIES HOISTS
250kg / 500kg 1 Tonne 2 Tonne
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
242015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
1 Tonne 3 Tonne2 Tonne 5 Tonne
Model 1/4S 1/4SN 1/2S 1/2SN 1S 1SN 2S 2SN 1/4S1 1/2S1 1S1 2S1
Z 450 450 450 450 530 530 645 645 450 450 530 645
A 181 183 181 183 216 216 216 216 181 181 246 246
B 184 210 184 210 216 246 216 246 210 210 246 246
C 125 125 125 125 135 135 90 90 125 125 135 90
D 165 185 165 185 170 170 215 215 165 165 170 215
E 620 620 620 620 680 680 705 705 620 620 680 705
G 19 19 19 19 23 23 26 26 19 19 23 26
Model 1F 2F 2FN 3F 3FN 5F 5FN
Z 535 660 660 820 820 1020 1020
A 250 280 280 280 280 280 280
B 250 280 330 280 330 280 330
C 135 175 175 120 120 145 145
D 170 170 170 245 245 330 330
E 680 845 845 1090 1090 1295 1295
G 23 26 26 42 42 48 48
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
25“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsHITACHI ET SERIES TROLLEYS
Model 1ET 2ET 3ET 5ET
B1 185 210 210 240
B2 190 210 210 240
D 64 75 75 90
d 27 32 37 46
F 303 313 316 323
H 226 245 265 322
K 136 130 140 177
T 65 80 80 90
U 55 40 37.5 54
V 159 172 175 181
L 182 200 203 219
W 120 148 148 173
E 133 169 168 202
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
262015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Electric Chain Hoists
The Pacific Electric Chain Hoists offer a great balance between quality and price. The models vary from 250kg to 2 tonne capacity and are all tested to the Australian standards. All hoists are inclusive of many features which makes them suited for most applications. Optional Motorised Trolleys are available to complete the package.
Features
• All Pacific models are manufactured to comply with AS1418.2.
• IP65 pendant with 24 volt control for operator safety.
• Overload protection clutch prevents damage caused by overloading.
• Inclusive of DC Brake which automatically engages in the event of a power failure.
• Completely enclosed design to withstand harsh conditions.
• Upper and lower electrical limit switches.
• Grade 80 zinc plated load chain supplied as standard.
• Motor thermal protection on all Pacific Electric Chain Hoists.
• Fuse protection provided for both primary and secondary control circuits.
• IP54 protection rating on all electric hoists and trolleys.
• Reverse phase protection relay on all models excluding 250kg.
• Optional radio remote control.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
27“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsSpecifications
Pacific Electric Chain Hoists - 415Volt, 50Hz
Model PEH025 PEH050 PEH100 PEH200
Stock Code PEH025 PEH050 PEH100 PEH200
Rated Capacity (kg) 250 500 1000 2000
Standard Lift Height (m) 3 3 3 3
Chain Dimension (mm) 4 X 12 6.3 X 19.1 7.1 X 20.2 7.1 X 20.2
Speed (m/min) 12/3 10/2.5 8/2 4/1
Motor (kW) 0.6 / 0.15 1.1 / 0.28 1.5 / 0.37 1.5 / 0.37
E.D Rating (%) 40 / 20 40 / 20 40 / 20 40 / 20
Load Chain Fall No. 1 1 1 2
Weight (kg) 30 42 57 62
Motorised Trolleys - 415Volt, 50Hz
Model PET050 PET100 PET200 PET055 PET105 PET205
Stock Code PET050 PET100 PET200 PET055 PET105 PET205
Rated Capacity (kg) 500 1000 2000 500 1000 2000
Speed (m/min) 10 10 10 20 / 5 20 / 5 20 / 5
Motor (kW) 0.12 0.18 0.37 0.12 / 0.03 0.18 / 0.04 0.37 / 0.09
*Standard beam sizes available up to 300mm width. Larger sizes available upon request.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
282015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Dimensions (in mm)
Pacific Electric Chain Hoists
Model PEH025 PEH050 PEH100 PEH200
A 380 468 487 487
B 175 221 240 240
C 205 247 248 248
D 135 156 170 170
E 299 366 398 398
F 143 186 188 188
G 156 180 210 210
H 376 485 520 592
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
29“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsPacific Electric Chain Hoists plus Trolley
Model PEH025 +PEH055
PEH050 +PET050
PEH100 +PET105
PEH200 +PET205
A 382 382 382 392
B 125.5 125.5 125.5 159
C 324 324 324 357
D 180 180 180 183
E 75 - 125 75 - 125 75 - 125 100 - 150
H 385 483 510 582
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
302015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Porta Hoists
The Pacific Porta Hoists are compact, lightweight 240 volt single phase electric chain hoists. They conveniently come in a durable travel case which makes them the ideal portable solution for lifting, lowering and handling loads up to 500kg. All models are tested to the Australian standards.
Features
• All Pacific Porta Hoists are manufactured to comply with AS1418.2.
• All models suitable for 240 volt, 50 Hz single phase power supply.
• Available in 80kg, 125kg, 250kg and 500kg capacities.
• Duty cycle rated at 30% ED with 180 starts per hour.
• 18 volt DC low voltage control for safe operation.
• IP65 pendant control, dual speeds with variable speed slow control for raise and lower.
• Overload protection clutch prevents damage caused by overloading.
• All models are supplied as standard with 6 metre height of lift, a 5 metre pendant control, chain bucket and 3 metre power supply cable.
• Upper and lower electrical limit switches.
• Supplied with durable travel case.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
31“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsSpecifications
Model PPH080 PPH125 PPH240 PPH500
Stock Code PPH080 PPH125 PPH240 PPH480
Rated Capacity (kg) 80 125 250 500
Standard Lift Height (m) 6 6 6 6
Pendant Length (m) 5 5 5 5
Power Supply 50Hz (volt) 240 240 240 240
Chain Dimension (mm) 4 .0 x 12 4 .0 x 12 4 .0 x 12 4 .0 x 12
Motor Power (kW) 0.3 0.3 0.6 0.6
Speed (m/min) 0 - 4.8 (varialble) / 18 0 - 3.2 (varialble) / 12.5 0 - 3.2 (varialble) / 12.5 0 - 1.6(varialble) / 6.3
IP Rating 54 54 54 54
E.D Rating (%) 30 30 30 30
E.D. Rating (%) 1 1 1 2
Weight (kg) 17.5 17.5 17.5 20.6
*Additional height of lift is available upon request. Please note that this may vary the size and weight of the hoist and
therefore may not fit into the travel case.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
322015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Dimensions (in mm)
Model PPH080 PPH125 PPH240 PPH500
A 364 364 364 364
B 182 182 182 182
C 182 182 182 182
D 89 89 89 89
E 423 423 423 423
F 6m lift 6m lift 6m lift 6m lift
G 25 25 25 25
H 25 25 25 25
I 260 260 260 260
J 108 108 108 84
K 152 152 152 176
L 400 400 400 494
1800 067 687
33“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsElectric Chains Hoists
Austlift AEC-1 415v3 Phase dual lifting speed Electric Chain Hoist is designed for optimum hoisting performance with features of durability, ease of operation and maintenance.
• Aluminium body.
• Capacities from 250kg to 10,000kg available.
• Auto power cut of to prevent damage from overloading.
• Brakes hold system in the event of power failure.
• Upper and lower electrical limit switches fitted.
• Fan cooled motor for thermal protection.
• Reverse phase protection relay fitted on all models.
• IP54 rated protection with 24 volt Pedant control.
• Quality Chain supplied by FEC Japan.
• All hoists are CE certified and comes with instructuin manual and Test Certificate.
• Load chain length of 4M and 6M as standard. Longer length are available upon request.
342015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Code WLL (T) Classification Duty Cycle
Power(kw)
Lifting Speed(m/min)
Load Chain N.W(Kg)
4M 6M
113024 114026 0.25 M6 80% 0.85 / 0.21 14 / 3.5 5 x 15 36 / 40
113054 114056 0.5 M6 60% 0.9 / 0.3 7.6 / 2.5 6.3 x 19 38 / 42
113104 114106 1 M6 50% 1.1 / 0.37 5 / 1.7 8 x 24 40 / 46
113204 114206 2 M6 50% 3 / 1 6 / 2 11.2 x 34 50 / 56
113304 114306 3 M4 40% 3 / 1 6 / 2 11.2 x 34 98 / 108
113504 114506 5 M4 40% 3 / 1 3 /1 11.2 x 3.4 105 / 115
113904 114906 10 M4 40% 2 x 3 / 1 3 /1 11.2 x 3.4 280 / 300
Code Dimension (mm)
4M 6M C D a b d e f g h
113024 114026 505 620 570/592 304 273 297/337 255 24 120
113054 114056 520 620 592/610 304 273 319/337 255 31 120
113104 114106 550 640 592/630 304 273 319/357 255 38 120
113204 114206 605 770 694/740 408 336 358/404 342 45 170
113304 114306 820 770 694/740 408 336 358/404 342 45 170
113504 114506 880 860 694/740 408 336 358/404 342 61 170
113904 114906 1320 1100 694/740 408 336 358/404 342 71 170
*Electrical Trolley available from 025T to 10T.
1800 067 687
35“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Care & Safety Instructions for Entertainment Hoists
Safety
Before Use
While in Operation
Moving heavy loads is hazardous. When lifting equipment is not used correctly or is poorly maintained, accidents and serious injury could result. The following safety precautions should be applied to the operation, maintenance and inspection of PWB Anchor entertainment hoist products.
• Always read the owner’s manual and safety instructions.• Never lift more than capacity shown on the hoist name plate.• Always check that the hook latches work properly and replace missing or broken hook latches.• Never operate a hoist if damaged or malfunctioning.• Never use a twisted, kinked, damaged or stretched load chain.• Never use a hoist if the hook latch is missing or broken.• Never use a hoist without a hoist name plate.• Never use a modified or deformed hook.• Never use a hoist in an explosive atmosphere.
• Never use a hoist for lifting, supporting or transporting people.• Never lift or transport loads over or near people.• Never support a load on the tip of the hook.• Always make sure that the load is properly seated in the hook.• Never use the hoist chain as a sling.• Never swing a suspended load.
WARNINGIMPROPER chain hoist use could result in death or serious injury
362015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
CM Entertainment Hoists 415v - 50Hz
The range of CM entertainment hoists from PWB Anchor are easy to handle, operate and maintain. Protected bya lifetime warranty (conditions apply) and designed for versatile operation in the inverted position, PWB Anchor entertainment hoists are supplied in a black powder coat finish and are available in a range of capacities that can be chained up to your specific lift requirements.
Voltage 415v - 50Hz
Low Voltage Control 24v control voltage
Enclosure Durable and lightweight housing. Cast aluminium, black powder coated finish for low visibility
Brake Heavy duty DC brake
Gearing Helical design for long wear life and smooth operation
Load Chain Designed and manufactured by Columbus McKinnon USA. Zinc plated to protect against corrosionBlack phosphate finish optional
Optional Features Chain bag - easy to mount cloth type bagsChain stop - mounted on load chain to prevent over-travel
» CM Lodestar Electric Hoist
The lodestar D8 is unsurpassed for reliability, a true industry leader. It’s clutch, outside the load path, acts as a precise overload device.
• Applications: Entertainment
• Australian Standard: AS1418.2
Capacity Part No. Model Lift Speed (m / min)
No. of Chains
Load Chain Dia (mm) x fall
Headroom (mm)
Load Chain Dia x Pitch (mm)
Load Chain Part No.
500kg 47112 F 4 1 6.3 x 1 413 6.3 x19 43746
1 Tonne 47113 L 4 1 7.9 x 1 472 7.9 x 21.8 46747
2 Tonne 47114 RR 2 2 7.9 x 2 613 7.9 x 21.8 46747
1800 067 687
37“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
CM Entertainment Hoists 415v - 50Hz
Control
Voltage
110 volt for long cable runs without voltage drop. Low voltage is available on request
Enclosure Lightweight, cast aluminium. Durable and strong black powder coated finish for low visibility
Brake DC mechanical brake for low maintenance and quiet operation
Gearing Precision machined gears, heat treated for strength and durability
Load Chain Designed and manufactured by Columbus McKinnon USA.Zinc plated to protect against corrosion. Black phosphate finish optional
» CM Prostar Electric Hoist
The CM Prostar Model is designed and built for the unique rigging applications typically encountered at small venues. Lightweight, quiet, portable and complete with overload protection. Pickle operated weiland tail optional.
• Applications: Entertainment
• Australian Standard: AS1418.2
Standard features include:
• Available in custom lift heights to suit your requirements.
• Chain stop mounted on load chain prevents over-travel.
• Overload protection helps prevent lifting of dangerous overloads.
• Units are not oil lubricated - no risk of oil on stage.
Capacity Part No. Model Lift Speed (m / min)
No. of Chains
250kg 44945 250 4 3.98
Headroom (mm)
Load Chain Dia x Pitch (mm)
Load Chain Part No.
281 3.98 x 11.98 44301
382015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Associated Entertainment Products
» Entertainment Clamps
Low visibility, black powder coat finish and simple to install. Suitable for use with powered hoists such as CM Lodestars and Prostars or chain blocks.
Standard features include:
• Load pin incorporated for load suspension with reduced headroom.
• Working load limit up to 9,890kg.
• Designed to fit flanges of most structural beams.
• Applications: Entertainment
• Australian Standard: AS1418.2
Size (mm)
WLL (tonnes)
Part No.
d (mm)
D (mm)
W (mm)
L (mm)
B (mm)
e (mm)
13 2.0 41794 13 16 21 48 33 33
16 3.25 41795 16 20 27 61 43 40
19 4.75 41796 19 22 32 72 51 48
Capacity Part No.
Bean Range (mm)
Headroom (min / mm)
Headroom (max / mm)
Suspension Weight (kg)
1 tonne 45785 65 - 230 78 135 20.3 4.8
» Entertainment Shackles
These shackles represent an easy and effective way of providing a connection of chain, wire rope or other rigging equipment.Supplied in a black powder coat finish for low visibility.
• Applications: Entertainment
• Australian Standard: AS 2741
1800 067 687
39“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Extras
» Chain Buckets / Bags
» Hoist maintenance and training
Standard lift hoists are fitted with either plastic chain buckets or canvas chain bags that suit a range of lifts. For longer lifts, PWB Anchor offers a range of larger canvas bags or steel buckets that may be attached to the hoists and cater for the storage of load chain during the lifting or lowering process.
Bag/bucket size is dependent on the height of lift and size of load chain used in the hoist.
As a leading supplier of power hoisting products, PWB Anchor is committed to providing reliable products to the highest standard. We are committed to providing training to ensure our hoist products are used safely.
PWB Anchor provides training through our distributors and directly to a wide variety of user groups. Maintenance and installation is also available through a range of service agents.
402015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
» EHL Series Chain Air Hoist
EHL Air hoists from Endo Kogyo are fitted with rotary vane motors in strong lightweight aluminium bodies, for easy handling in a variety of industrial and construction applications. Variable speed models available in either cord or pendant controls with optional lift heights.
Standard features include:
• Compact and lightweight ensures ease of handling.
• Operation speed depends on the amount of pressure applied to the push buttons or how hard the control rope is pulled.
• Installation - simply connect the air hose.
• Precise variable lifting and high speed.
• Quality load chain allowing high frequency of use.
• Upper and lower limit switches.
• Applications: Mining, construction, engineering, offshore
• Australian Standard: AS1418.2
Capacity
Part No.
3 Metre
(Pendant)
Part No. 3
Metre (Pull
Cord)
ModelLift Speed
(m / min)
Load Chain dia
(mm) x falls
Headroom
(mm)
Weight
(kg)
Load Chain Dia
x Pitch (mm)
Load Chain
Part No.
125kg 44519 NA AT125K 14.5 4.0 x 1 790 12.5 4 x 12 48351
500kg 49251 49250 EHL05ST 10.5 6.3 X 1 365 19 6.3 X 19 43206
1 Tonne 49253 49252 EHL1TW 5.2 6.3 x 2 440 25 6.3 X 19 43206
1 Tonne 63538 48237 EHL1ST 6.0 7.1 x 1 480 34 7.1 x 21 46745
2 Tonne 48238 48239 EHL2TW 3.0 7.1 x 2 540 42 7.1 x 21 46745
3 Tonne 44181 44998 EHL3TS 3.0 12.5 x 1 585 75 12.5 x 38 46752
6 Tonne 47609 45000 EHL6TW 1.5 12.5 x 2 770 96 12.5 x 38 46752
1800 067 687
41“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
» MTH Series Air Trolley
• Used in conjunction with the EHL Air Hoist.
• Designed for easy handling and high speed performance.
• Available in pendant control with 2 directional functions.
• Applications: Mining, construction, engineering, offshore
• Australian Standard: AS1418.2
Capacity Part No. ModelTravel Speed
(m / min)
Beam Range
(mm)
Mini Beam
RadiusControl Type Weight (kg)
Standard Flange Width1 Tonne 44610 MTH - 1T 28.0 75 - 125 800 Pendant 35.0
2 Tonne 44611 MTH - 2T 18.0 125 - 150 1000 Pendant 63.0
6 Tonne 44612 MTH - 6.3T 19.0 150 - 190 2500 Pendant 127.0
Wide Beam Flange Width
1 Tonne TBA MTH - 1T 28.0 154 - 305 800 Pendant 35.0
2 Tonne TBA MTH - 2T 18.0 154 - 305 1000 Pendant 63.0
6 Tonne TBA MTH - 6.3T 19.0 154 - 305 2500 Pendant 127.0
422015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Standard features include:
• Heat treated planetary reduction gears are small and lightweight and can take a large speed reduction ratio.
• Control valve is engineered with spool valves of spring return in 2 positions and 3 ports. The valve works by controlling the lever switch connected with the spool.
• The cone brake system is suited to wire rope hoists and has a contol valve integrated with the proper speed reduction mechanism at air motor, finally achieving the excellent control.
• Reverse winding protection is incorporated in EHW air hoist series. When the wire rope is pulled out 1.9m, the system makes the air motor stop automatically.
• Applications: Mining, construction, engineering.
• Australian Standard: AS1418.2
Capacity Part No. ModelStandard
Lift (m)
Lift Speed (m /
min)
Headroom Hook
Suspended (mm)Control Type Weight (kg)
120kg 44992 EHW - 120 1.9 16.0 680 On Hook 9.5
120kg 44993 EHW - 120R 1.9 16.0 630 Pendant 9.7
250kg 44182 AH - 250R 2.5 11.0 745 Pendant 18.2
» EHW Series Air Hoists
Designed for Wire Rope lift, the ENDO EHW Air Hoist is available in hook or pendant control with a cone brake system.
1800 067 687
43“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Anchor Extras
» Radio Remote Controls
» Cable Trolleys
» Chain Buckets / Bags
» Extra Close Headroom Hoists
» Hoist Maintenance and Training
To complement the power hoisting product range, PWB Anchor offers a range of products with additional benefits to suit your requirements.
When the traditional hand held Pendant Control becomes cumbersome or does not suit the application, PWB Anchor offers a Radio Remote Control system that allows the operator to work away from the hoist, yet be in control of its operation. Complete with a transmitter and receiver system that can be operated from various angles and distances, thereby allowing for platform or restricted access use.
This feature can be fitted to a range of electric hoists to suit your application.
Specifically designed to suspend the power supply cable to your hoist or motorised trolley. These small cable trolleys are supplied with the power cable or can be purchased seperately. Cable Trolleys can be fitted and suspended on 4mm cable wire.
Standard lift hoists are fitted with either plastic chain buckets or canvas chain bags. For longer lifts, PWB Anchor offers a range of larger canvas bags or steel buckets that may be attached to the hoists and cater for the storage of load chain during the lifting or lowering process.
This feature is dependant on the length of lift and size of load chain used in the hoist.
Some workplace environments restrict or limit space and access. Should your application have a limited space or headroom problem, PWB Anchor is able to assist with extra close headroom hoists, either from our existing range or from one of our specialised suppliers.
As a leading supplier of power hoisting products, PWB Anchor is committed to providing reliable products of the highest standard. We are commited to providing the training on our hoist products to ensure they are used safely.PWB Anchor provides training through our distributors and directly to a wide variety of user groups. Maintenance or repair is also available through a range of service agents.
442015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Commonly Asked Questions
» Electric Chain Hoists
• Are ER2 Electric Hoists available in an explosive proof version?No. However, PWB Anchor do have air operated explosion proof hoists available.
• What makes the ER2 Hoist environmentally friendly?Energy saving: An energy saving can be made due to the reduction in rated current drawn compared to the previous
model, ER.
Lower Noise: The utilisation of the inverter, 4-pole motor as well as the electromagnetic brake reduces the noise
during operation and braking.
Hazardous substances outlined in the restriction of hazardous substances (ROHS) directive are not used.
• What is the difference between a Chain Block and a Chain Hoist?A Chain Block is a manual lifting device. A Chain Hoist is a power operated lifting device.
• What does the IP rating for an electric hoist refer to?The IP rating is a weather protection rating. IP means ingress protection and is shown, for example, as IP55. The
first number relates to dust protection. 5 means the unit is sealed to prevent sufficient dust entering the hoist which
could interfere with normal operation. The second number relates to water ingress. A rating of 5 stipulates the hoist
is protected against low pressure water jets from all directions.
• Can I add chain to extend the height of lift of a hoist?Chain can not be joined together to extend the lift of any hoisting product. To satisfy this requirement, a
new length of chain must be purchased and fitted by a competent person. It then needs to be tested to ensure the
product has been assembled correctly and re- certified.
• Where can I get PWB Anchor Hoists serviced?PWB Anchor can recommend accredited service agents throughout Australia.
1800 067 687
45“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
• Is the emergency stop feature standard on ER2 Electric Chain Hoists?Yes it is, allowing the motor power to be disconnected from the main power supply in any emergency.
• Can I use a KITO Electric Hoist upside down?No, due to the mechanics and lubricants in the hoist, this is not a recommended practice. However, PWB Anchor has
a range of CM Lodestar or Prostar motors that are specifically designed for the entertainment industry that can be
used in the inverted position.
• Which hoists are suited for use in the entertainment industry?PWB Anchor has a wide range of hoists that are suited for operation in the entertainment industry. They include CM
Lodestar, CM Prostar, Kito ER2 and Kito ED Electric Chain Hoists.
• Can ER2 Electric Hoists be supplied with longer lift heights?Yes. ER2 Electric Hoists are available in many different lift heights to suit your requirements.
• Can ER2 Electric Hoists be used outdoors?Yes, ER2 Hoists that are rated IP55. This means they have protection from direct jet spray and dust particles. Also
they have a strong epoxy coated painted body and the load chain is Nickel-plated, which is corrosion and abrasion
resistant. However to better protect the hoist in external applications a cover is recomended.
• Do you get 2 pendants with electric hoist and motorised trolley combinations?These come with one pendant that controls the entire assembly.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
462015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
JDN Air Hoists
J.D. Neuhaus manufactures high quality, superior PROFI Air Hoists which are known for their robust designs. This makes their products suitable for tough industrial applications, even in continuous working processes. Safety features, as 100% duty rating and explosion protecting, are an important advantage for applications in hazardous areas.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Patented pre-lube motor design for low maintenance, oil-free operation.
• 100% duty rating and unlimited duty cycle suits all environmental conditions.
• Only six atmospheres of compressed air required.
• Insensitive to dust, humidity and temperatures ranging from -20 °C up to + 70 °C.
• ATEX–approved models available, suitable for application in dangerous and explosive environments.
• Self-cooling economic air motor which will not overheat.
• Fail-safe brake, in case of air supply failure.
• From 1 tonne upwards available with overload protection.
• Low decibel rating.
• F-type sensitive infinitely variable speed control for the precise positioning of loads.
• Cord control or Brass Pendant control available, as well as an electro pneumatic interface for Radio Remote control as an option.
• Easy operation and low maintenance design.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
47“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsSpecifications
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti
Stock Code JDN705 JDN706 JDN715 JDN719 JDN725 JDN735
Rated Capacity (kg) 0.25 0.5 1 1.6 2 3.2
Weight with standard 3m lift (m) 27 27 28 56 34 86
No. of chain strands 1 1 1 1 2 1
Motor Power (kW) 1.0 1.0 1.0 1.3 - 2 1.0 3.5
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 9 x 27 7 x 21 13 x 36
Air Pressure (bar) 6 6 6 4 - 6 6 6
Air Consumption at full load (m3/min)LiftingLowering
1.21.5
1.21.5
1.21.5
1.5 - 2.62.2 - 3.6
1.21.5
45.5
Air Connection G 1/2 G 1/2 G 1/2 G 3/4 G 1/2 G 3/4
Lifting speed at full load (m/min) 20 11 5.5 4 - 6 2.7 5
Lowering speed at full load (m/min) 38 17 11 11 - 12 5.5 10.8
Model 3Ti/2 6Ti 10Ti 16Ti 20Ti
Stock Code JDN732 JDN765 JDN775 JDN785 JDN795
Rated Capacity (tonne) 3.2 6.3 10 16 20
Weight with standard 3m lift (m) 66 110 156 240 285
No. of chain strands 2 2 2 3 4
Motor Power (kW) 1.3 - 2 3.5 3.5 3.5 3.5
Chain Dimension (mm) 9 x 27 13 x 36 16 x 45 16 x 45 16 x 45
Air Pressure (bar) 4 - 6 6 6 6 6
Air Consumption at full load (m3/min)LiftingLowering
1.5 - 2.62.2 - 3.6
45.5
45.5
45.5
45.5
Air Connection G 3/4 G 3/4 G 3/4 G 3/4 G 3/4
Lifting speed at full load (m/min) 2 - 3 2.5 1.6 1 0.7
Lowering speed at full load (m/min) 5.5 - 6 5.4 3.4 2.1 1.6
*PROFI range available up to 100 tonne.**Chain buckets, longer lift heights and alternative controllers available at additional cost. ***Weight and headroom based on PROFI standard model with rope control and no chain bucket.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
482015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Dimensions (in mm)
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti 20Ti
A (min. headroom1)
450 450 450 480 498 593 544 674 813 898 1030
B 288 288 288 293 336 373 356 454 548 598 670
C 145 145 145 200 145 233 200 233 308 382 382
D 297 297 297 412 297 483 412 483 575 692 692
E1 28 28 28 28 28 40 28 40 44 53 75
E2 28 28 28 26 28 30 28 40 44 53 75
F (up to hook centre)
137 137 137 170 137 187 140 154 197 199 180
G (max. width) 176 176 176 215 183 233 215 233 306 308 315
1Chain buckets increase the hoist headroom
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
49“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsJDN Mining Air Hoists
The JDN M-series are specifically designed for underground mining operations where loads can be lifted, lowered and horizontally pulled. Due to their versatility, they are also suitable for many different industrial applications. The M-series have the same features as the JDN PROFI-series, however; they operate with an air pressure of only 4 bar.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Patented pre-lube motor design for low maintenance, oil-free operation.
• 100% duty rating and unlimited duty cycle suits all environmental conditions.
• Insensitive to dust, humidity and temperatures ranging from -20 °C up to + 70 °C.
• ATEX–approved models available, suitable for application in dangerous and explosive environments.
• Fail-safe brake, in case of air supply failure.
• Cast iron housing suitable for severe conditions.
• Easy operation and low maintenance design.
• Two chain falls for operation in both directions.
• Specially designed for horizontal and vertical moving of loads.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
502015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Specifications
Dimensions (in mm)
Model M64 M63D
Stock Code JDN991 JDN990
Rated Capacity (tonne) 1 - 2 3 - 6
Weight with standard 3m lift (kg) 60 100
No. of chain strands 1 - 2 1 - 2
Motor Power (kW) 0.77 1.3
Chain Dimension (mm) 9 x 27 13 x 36
Air Pressure (bar) 4 4
Air Consumption at full load (m3/min)LiftingLowering
1.02.0
2.23.2
Air Connection Rd 32 x 1/8” Rd 32 x 1/8”
Lifting speed at full load (m/min) 3 - 1.5 2.2 - 1.1
Lowering speed at full load (m/min) 12.5 - 6.5 6 - 3
Model M64 M63D
A1 (smallest headroom with 1/1 chain strands)
603 750
A2 (smallest headroom with 1/2 chain strands) 660 870
B1 (with 1/1 chain strands) 313 370
B2 (with 1/2 chain strands) 370 490
C 175 237
D 375 507
E1 (Hook opening) 30 40
E2 (Hook opening) 30 40
E3 (Hook opening) 30 30
F (maximum width) 144 195
* Custom lift heights available. Weight based on standard model.Lifting speed at 2m length of control. Longer control hoses decrease the lifting speeds.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
51“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsJDN Mini Air Hoists
The JDN Mini Series widens the range of applications in the light duty sector as a handy, flexible and light-weight hoist. The optional Mini Manipulator can be used to lift, lower, traverse and position loads in an easy, manual manner. The carrying capacities vary from 125kg to 980kg, with the 125kg model and the 250kg available with optional travel case.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Patented pre-lube motor design for low maintenance, oil-free operation.
• 100% duty rating and unlimited duty cycle suits all environmental conditions.
• Only six atmospheres of compressed air required.
• Insensitive to dust, humidity and temperatures ranging from -20 °C up to + 70 °C.
• ATEX–approved models available, suitable for application in dangerous and explosive environments.
• Also suitable for horizontal pulling.
• Self-cooling economic air motor which will not overheat.
• Fail-safe brake, in case of air supply failure.
• Wear resistant motor braking system.
• Extremely sensitive lever control with emergency shut-off valve; maximum control length is 6 metres.
• Price competitive alternative when compared to other types of powered hoists.
• Easy operation and low maintenance design.
• Lightweight for easy handling.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
522015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model Mini125 Mini250 Mini500 Mini1000
Stock Code JDN123 JDN253 JDN503 JDN603
Rated Capacity (kg) 125 250 500 980
Weight with standard 3m lift (kg) 9.5 10.5 21 23
No. of chain strands 1 1 1 1
Motor Output (kW) 0.4 0.4 1 1
Chain Dimension (mm) 4 x 12 4 x 12 7 x 21 7 x 21
Air Pressure (bar) 6 6 6 6
Air Consumption at full load (m3/min)LiftingLowering
0.50.7
0.50.7
1.21.6
1.21.6
Air Connection G3/8 G3/8 G1/2 G1/2
Lifting speed at full load (m/min) 15 8 10 5
Lowering speed at full load (m/min) 30 16 18 10
Model Mini125 Mini250 Mini500 Mini1000
A 328 328 458 458
B 232 232 316 316
C 367 367 505 505
D 92 92 122 122
E 213 213 292 292
F 109 109 148 148
G 104 104 144 144
H 177 177 234 234
J 148 148 194 194
K 83 83 119 119
L 29 29 40 40
M 19 19 28 28
* Custom lift heights available. Weight and headroom based on mini standard model with pendant control and chain bucket.** Pneumatic trolleys and cord controls not available for this range.
Specifications
Dimensions (in mm)
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
53“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsJDN Hydraulic Monorail Hoists
The JDN Hydraulic Monorail Hoists can be deployed as an alternative to air driven units in all situations where hydraulic lines, central hydraulic systems or hydraulic power supplies exist. The carrying capacities vary from 3 tonne up to 100 tonne and depending on the motor size; these hoists work with an intake pressure of 100 bar up to 180 bar.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Ideal for applications in explosion risk areas.
• Sensitive, infinitely variable speed control of lifting / lowering and travelling motions.
• Extremely low noise emissions.
• Fully enclosed highly robust gear motor.
• Integrated overload protection.
• Only two supply connections at hoist “P” and “T”, leakage oil drained internally.
• Controlled load-lowering up to 20 tonne carrying capacities in the event of oil supply failure.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
542015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model 3 TI-H 6 TI-H 10 TI-H 16 TI-H 20 TI-H
Stock Code - - - - -
Rated Capacity (tonne) 3.2 6.3 10 16 20
No. of chain strands 1 2 2 3 4
Motor Type KM 1/16 KM 1/16 KM 1/16 KM 1/16 KM 1/16
Motor Power (kW) 3.5 3.5 3.5 3.5 3.5
Intake Pressure (bar) 130 130 130 130 130
Intake Volume (l/min) 48 48 48 48 48
Lifting speed at full load (m/min) 4.0 2.0 1.7 1.1 0.8
Lowering speed at full load (m/min) 4.5 2.3 2.1 1.5 1.0
Weight with standard lift height (kg) 90 114 160 244 289
Chain Dimension (mm) 13 x 36 13 x 36 16 x 45 16 x 45 16 x 45
Weight of chain (kg/m) 3.8 3.8 5.8 5.8 5.8
Standard Lift (m) 3 3 3 3 3
Length of control as standard lift (m) 2 2 2 2 2
Specifications
JDN Hydraulic PROFI Hoists (available up to 100 tonne)
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
55“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsJDN Hydraulic Monorail Hoists
Model EH 20 H EH 25 H EH 37 H EH 50 H EH 75 H EH 100 H
Stock Code JDN810 - - JDN850 - -
Rated Capacity (tonne) 20 25 37.5 50 75 100
No. of chain strands 4 2 3 4 3 4
Motor Type – Trolley KM 1/16 KM 1/16 KM 1/16 KM 1/16 KM 1/16 KM 1/16
Motor Type – Hoist KM 1/8 - KM 1/16 KM 2/32 KM 2/32 KM 2/32 KM 2/32 KM 2/32
Motor Output – Trolley (kW) 0.7 1.4 1.4 1.4 2.8 2.8
Motor Output – Hoist (kW) 3.5 6 6 6 10 10
Intake Pressure (bar) 160/100 150 150 150 180 180
Lifting speed at full load (m/min) 0.8 1.1 0.7 0.5 0.7 0.55
Lowering speed at full load (m/min) 0.9 1.2 0.8 0.6 0.8 0.6
Travelling Speed 12 12 12 12 12 12
Connection G1/2 G3/4 G3/4 G3/4 G3/4 G3/4
Hose Dimension DN 12 DN 16 DN 16 DN 16 DN 16 DN 16
Weight with standard lift height (kg) 720 1050 1550 1880 4100 5800
Chain Dimension (mm) 16 x 45 23.5 x 66 23.5 x 66 23.5 x 66 32 x 90 32 x 90
Weight of chain (kg/m) 5.8 12.2 12.2 12.2 21.3 21.3
Standard Lift (m) 3 3 3 3 3 3
Dimensions (in mm)JDN Hydraulic PROFI Hoists
Model 3 TI-H 6 TI-H 10 TI-H 16 TI-H 20 TI-H
A (smallest headroom¹) 593 674 813 898 1030
B 373 454 548 598 670
C 233 233 308 382 382
D 578 578 670 787 787
E1 40 40 44 53 75
E2 30 40 44 53 75
F 187 154 197 199 180
¹Chain buckets increase the hoist headroom
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
562015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Dimensions (in mm)
JDN Hydraulic Monorail Hoists
Model EH 20-H EH 25-H EH 37-H EH 50-H EH 75-H EH 100-H
A 130 146 146 125 100 125
B 68 70 70 68 68 68
C 267 257 267 272 267 272
D 35 25 25 40 35 40
E 220 198 220 283 220 283
F1 820 998 1070 1150 1480 1535
G 200 170 190 420 286 575
H 75 75 100 100 120 120
J 266 350 455 340 740 470
K 600 1185 1730 1680 3210 3130
L 367 377 377 462 640 762
M 420 562 562 687 670 765
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
57“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsJDN Big Bag Handling Air Hoists
For Big Bag Handling JDN offers innovative design solutions to meet the special requirements for these applications. These Air Hoists are available in capacities of 1100kg and 2200kg with an air pressure of 6 bar and are supplied with one or two load hooks. One load hook for standard cross lifting beam design. The extended distance between the hook and the chain box is particularly advantageous since this guarantees no risk of collision between the load and the chain box. The twin loads hooks are suited for more complex multipoint cross beam designs or for standard lifting beam designs with two suspension points.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Particularly suited for use as big bag handling hoist and for the movements of bulky loads due to the low headroom design.
• Compact and modern design.
• Suitable for use as a synchronized hoist in twin-hook design.
• The use of JDN standard components guarantees reliable operation and cost effective manufacture.
• No additional motor lubrication required.
• Small number of maintenance / wear free moving parts.
• Chain box included as standard.
• Suitable for a wide variety of beam sizes / profiles, with hook centres to suit your requirements.
• 100% duty rating and unlimited duty cycle suits all environmental conditions.
• Suitable for use as standard in areas at risk of explosion with ATEX–approved models available, for application in dangerous and explosive environments.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
582015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model BBH 1000-1 BBH 2000-1 BBH 1000-2 BBH 2000-2
Stock Code JDN900 - - -
No. of hooks 1 1 2 2
Air Pressure (bar) 6 6 6 6
Rated Capacity (tonne) 1.1 2.2 1.1 2.2
No. of chain strands 1 2 2 4
Motor Output – Hoist (kW) 0.7 0.7 0.7 0.7
Motor Output – Trolley (kW) 0.2 0.2 0.2 0.2
Lifting speed at full load (m/min) 3.7 1.7 3.7 1.7
Lowering speed at full load (m/min) 10 5 10 5
Air consumption at full load (m³/min) 1.4 1.4 1.4 1.4
Weight with standard lift andminimum k dimension (kg)
130 137 137 149
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 7 x 21
Weight of 1m chain (kg) 1 1 1 1
Standard Lift (m) 3 3 3 3
Length of control at standard load (m) 2 2 2 2
Noise level at full load (dB (A)) 76 76 76 76
Specifications
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
59“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists
Model BBH 1000-1 BBH 2000-1 BBH 1000-2 BBH 2000-2
A 332 332 332 332
B 163 / 220 163 / 220 163 / 220 163 / 220
b min. 90 90 90 90
b max. 310 310 310 310
C 182 182 182 182
E 195 195 373 346
F 195 195 95 95
G 195 195 159 159
H 388 388 388 438
J 192 220 192 220
K min. 435 410 260 260
K max. 1100 1100 1300 1300
L - - 175 150
M 28 28 28 28
N 250 250 250 250
P 70 70 70 70
R 116 116 116 116
t max. 30 30 30 30
Dimensions (in mm)
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
602015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
JDN Ultra Low Monorail Hoists
The JDN Ultra Low Monorail Hoist provides the ideal solution when loads have to be lifted andtransported in extremely reduced spaces. As an example; the model with a 6 tonne load capacityfeatures a headroom of only 230mm. The carrying capacity of these models vary from 4 tonne up to 100tonne, with an air pressure of 6 bar.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Ideal for applications in explosion risk areas.
• Insensitive to dust, humidity and temperatures ranging from -20 °C up to + 70 °C.
• Extremely low headroom.
• Low air consumption.
• Available with increased spark protection.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
61“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists
Model UH 4 UH 6 UH 8 UH 12 UH 16
Stock Code - JDN806 JDN808 JDN999 -
Rated Capacity (tonne) 4 6 8 12 16
No. of chain strands 2 2 4 4 4
Air pressure (bar) 6 6 6 6 6
Motor Output (kW) 2.5 2.5 2.5 2.5 2.5
Lifting speed at full load (m/min) 3.0 2.0 1.4 0.9 0.65
Lowering speed at full load (m/min) 7.5 5.2 3.6 2.5 1.5
Air consumption at full load (m3/min) 4.0 4.0 4.0 4.0 4.0
Weight with standard lift and control length (kg)
460 470 540 550 560
Chain Dimension (mm) 13 x 36 13 x 36 13 x 36 13 x 36 13 x 36
Weight of 1 m chain (kg) 3.8 3.8 3.8 3.8 3.8
Standard Lift (m) 3 3 3 3 3
Length of control as standard load (m) 2 2 2 2 2
Noise level at full load lifting (dB (A)) 78 78 78 78 78
Noise level at full load lowering (dB (A)) 80 80 80 80 80
Specifications
*Capacities up to 100 tonne available on request
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
622015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
JDN Trolleys
JDN Trolleys are available for both the PROFI and Mining Air Hoists as a manual option (LN) for pushingor pulling by hand. Geared trolleys (LH) are also available for load movement by operating the handchain mechanism and JDN also offers a motorised trolley (LM) which is powered by an air motor. Thecarrying capacities go up to 20 tonne.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Easy to install.
• Fitted with Anti-climb and anti-drop devices as standard.
• Robust manufacture requiring little maintenance.
• Able to negotiate curves.
• Rack and pinion drive and spark resistance package available as options.
• Four coat epoxy paint finish available for offshore protection.
• The air supply can be fed by various systems; energy chain, c-rail, square rail, spiral hose or hose trolleys.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
63“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti 20Ti
Stock Code - JDN925 JDN925 - JDN925 JDN931 - JDN960 JDN970 JDN970 JDN970
Rated Capacity - LN Trolley (tonne)
0.5 0.5 1 2 2 3.2 3.2 6.3 10-16 10-16 -
Rated Capacity - LH & LM Trolley (tonne)
2 2 2 2 2 3.2 3.2 6.3 10-16 10-16 20
Rated Capacity - Hoists incl. Trolley (tonne)
0.25 0.5 1 1.6 2 3.2 3.2 6.3 10 16 20
Weight - LN Trolley (kg) 7.7 7.7 10.5 18 18 26 26 117 190 190 -
Weight - LH Trolley (kg) 26 26 26 26 26 37 37 127 220 220 285
Weight - LM Trolley (kg) 26 26 26 26 26 33 33 124 220 220 285
Hose weght with standard lift (kg)
27 27 28 56 34 86 66 110 156 240 285
Weight with standard lift - LN trolley (kg)
34.7 34.7 38.5 74 52 112 92 227 346 430 -
Weight with standard lift - LH trolley (kg)
53 53 54 82 60 123 103 237 376 460 570
Weight with standard lift - LM trolley (kg)
53 53 54 82 60 119 99 234 376 460 570
Weight of 1m chain (kg) 1 1 1 1.8 1 3.8 1.8 3.8 5.8 5.8 5.8
No. of chain strands 1 1 1 1 2 1 2 2 2 3 4
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 9 x 27 7 x 21 13 x 36 9 x 27 13 x 36 16 x 45 16 x 45 16 x 45
Air Pressure - LM trolley (bar)
6 6 6 4 - 6 6 6 4 - 6 6 6 6 6
Air Consumption - LM
trolley (m3/min)0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 1.3 1.3 1.3
Air Consumption - Hoist
(m3/min)1.5 1.5 1.5 1.5-2.6 1.5 5.5 1.5-2.6 5.5 5.5 5.5 5.5
Motor Output - LM Trolley (kW)
0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.7 0.7 0.7
Motor Output -Hoist (kW) 1 1 1 1.3 - 2 1 3.5 1.3 - 2 3.5 3.5 3.5 3.5
Travelling Speed - LM Trolley (m/min)
9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 5 / 12 5 / 12 5 / 12
Hose connection- LM Trolley
G 1/2 G 1/2 G 1/2 G 3/4 G 1/2 G 3/4 G 3/4 G 3/4 G 3/4 G 3/4 G 3/4
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
642015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti
With trolley LN 0.5T LN 1T LN 2T LN 3.2T LN 6.3T LN 10-16T
A 260 260 260 310 310 292 292 500 490 490
B max. 119 119 122 122 162 113 162 141 142 142
C b + 28 b + 28 b + 28 b + 26 b + 26 b + 60 b + 60 b + 70 b + 70 b + 70
d 55 55 68 80 80 84 84 165 165 165
D max 199 199 199 122 122 113 113 141 142 142
E 137 137 137 170 137 187 140 154 197 199
F 39 39 39 45 46 46 75 79 109 109
G 145 145 145 200 145 233 200 233 308 382
H 152 152 152 212 152 250 212 250 267 310
J* (mounted) - - - - - 635 613 763 929 982
J* (suspended) 530 530 530 588 597 798 - 919 1176 1260
K 67.5 67.5 81.5 94 94 108 107 188 188 188
L 28 28 28 26 28 30 28 40 44 53
M 42 42 42 40 42 42 42 51 66 82
N 130 130 130 150 150 136 136 236 236 236
JDN Manual Trolleys (LN)
*Chain buckets increase the hoist headroom
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
65“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti 1/2 6Ti 10Ti 16Ti 20Ti
With trolley LH 2T LH 3.2T LH 6.3T LH 10 - 16 LH 20T
A 250 250 250 250 250 292 292 500 490 490 600
B max. 130 130 130 130 130 113 113 141 142 142 132
C b + 36 b + 36 b + 36 b + 36 b + 36 b + 60 b + 60 b + 70 b + 70 b + 70 b+68
d 70 70 70 70 70 84 84 165 165 165 185
D 284 284 284 283 284 294 297 307 320 320 320
E 137 137 137 170 137 187 140 154 197 199 180
F 39 39 39 45 46 46 75 79 109 109 135
G 145 145 145 200 145 233 200 233 308 382 382
H 152 152 152 212 152 250 212 250 267 310 310
J* (mounted) - - - - - 635 613 763 929 982 1125
J (*) (suspended) 563 563 563 602 611 798 - 919 1176 1171 1475
K 103 103 103 103 103 110 110 215 215 215 226
L 28 28 28 26 28 30 28 40 44 53 75
M 42 42 42 40 42 42 42 51 66 82 86
N 116 116 116 116 116 136 136 236 236 236 274
JDN Geared Trolleys (LH)
*Chain buckets increase the hoist headroom
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
662015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti1/2 6Ti 10Ti 16Ti 20Ti
With trolley LM 2T LM 3.2T LM 6.3T LM 10 - 16T LM 20T
A 250 250 250 250 250 292 292 500 490 490 600
B max. 130 130 130 130 130 113 113 141 142 142 132
C b + 36 b + 36 b + 36 b + 36 b + 36 b + 60 b + 60 b + 70 b + 70 b + 70 b+68
d 70 70 70 70 70 84 84 165 165 165 185
D 183 183 183 185 183 191 191 205 328 328 328
E 137 137 137 170 137 187 140 154 197 199 180
F 39 39 39 45 46 46 75 79 109 109 135
G 145 145 145 200 145 233 200 233 308 382 382
H 152 152 152 212 152 250 212 250 267 310 310
J* (mounted) - - - - - 635 613 763 929 982 1125
J* (suspended) 563 563 563 602 611 798 - 919 1176 1171 1475
K 95 95 95 95 95 107 107 188 188 188 218
L 28 28 28 26 28 30 28 40 42 55 75
M 42 42 42 40 42 42 42 51 66 82 86
N 116 116 116 116 116 136 136 236 236 236 274
JDN Motorised Trolleys (LM )
*Chain buckets increase the hoist headroom
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
67“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsJDN Low Headroom Trolleys
The JDN Low Headroom Trolleys are the solution where headroom is restricted and standard trolleysare unable to meet the lifting height requirements. This, together with having the JDN Air Hoist mountedin a horizontal position, could just be the answer in a difficult lifting situation. The carrying capacity ofthese models vary from 0.5 tonne up to 6.3 tonne, with an air pressure of 6 bar.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Small number of maintenance / wear-free moving parts.
• No additional motor lubrication required.
• Two-step travelling speed.
• Adjustable trolley widths to suit your requirements.
• Able to negotiate curves.
• Extended trolley tie bars for bulky elongated loads.
• Optional Rack and pinion drive, off shore paint and spark resistant packages available
• Various options for Air supply systems available.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
682015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Hoist & Trolley Model PROFI 0.5Ti& LMF05 - 2t
PROFI 1Ti& LMF05 - 2t
PROFI 2Ti& LMF05 - 2t
PROFI 3Ti& LMF3.2t
PROFI 6Ti& LMF6.3t
Stock Code JDN706 JDN715 JDN725 JDN735 JDN765
Rated Capacity (tonne) 0.5 1 2 3.2 6.3
No. of chain strands 1 1 2 1 2
Motor Output – Hoist (kW) 1 1 1 3.5 3.5
Motor Output – Trolley (kW) 0.2 0.2 0.2 0.2 0.2
Air Pressure (bar) 6 6 6 6 6
Lifting speed at full load (m/min) 10 5 2.5 4.5 2.2
Lowering speed at full load (m/min) 17 11 5.5 10.8 5.4
Travelling speed at full load (m/min) 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14
Air consumption at full load (m3/min) 1.2 1.2 1.2 1.2 1.2
Air Connection G 1/2 G 1/2 G 1/2 G 3/4 G 3/4
Hose Dimension (mm) 13 13 13 19 19
Weight with standard lift & control (kg) 98 99 105 210 330
Chain Dimension (mm) 7 X 21 7 X 21 7 X 21 13 X 36 13 X 36
Weight of chain (kg) 1 1 1 3.8 3.8
Standard Lift (m) 3 3 3 3 3
Max. bottom fiange - thickness (mm) 25 25 25 35 35
Max. bottom fiange - width (mm) 310 310 310 310 310
Min. bottom fiange - width (mm) 80 80 80 125 125
Noise level at full load lifting (dB (A)) 75 76 76 78 78
Noise level at full load lowering (dB (A)) 78 78 78 80 80
Specifications
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
69“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Hoists
Hoists & Trolley Model PROFI 0.5Ti &LMF 05 - 2t
PROFI 1Ti &LMF 05 - 2t
PROFI 2Ti &LMF 05 - 2t
PROFI 3Ti &LMF 3.2t
PROFI 6Ti &LMF 6.3t
A max. 105 105 105 105 106
B 36 36 36 36 70
b min. 80 80 80 80 125
C 164 164 164 164 169
D1 70 70 70 70 165
D2 70 70 70 70 70
E1 116 116 116 116 236
E2 116 116 116 116 116
F 172 172 195 228 351
G1 95 95 95 95 197
G2 95 95 95 95 95
H min. 320 320 394 415 537
J 320 320 320 397 397
K1 145 145 145 233 233
K2 152 152 152 248 248
L 715 715 715 825 995
M 28 28 28 30 40
N 42 42 42 42 51
t max. 25 25 25 35 35
Dimensions (in mm)
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
702015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
JDN Controls
JDN Air Hoists are available with various controls to suit every application.
Rope Control
The rope control provides infinite speed control for lifting and lowering and is suitable for any required control length. The rope control is available for all PROFI hoists up to 25 tonne carrying capacity. The PROFI 37Ti, 50Ti and 100Ti are fitted with a pull chain instead of a cord.
FI-Control
This FI-control allows infinitely variable speed control and the ergonomic design of the synthetic housing ensures comfortable handling for the operator. The use of non-rusting materials allows the application in areas with aggressive substances in the atmosphere. The control hoses are enclosed in an outer sheath which protects them from external conditions.
F-Control
The F-control consists of unbreakable synthetic material resistant to ambient influences. The ergonomically designed housing ensures ease ofhandling. Up to 18 different control functions can be integrated into a single pendant control; for example key switch, double stage travelling speed and simultaneous control of several motors. The F-control can alsobe delivered with optional infinitely variable control of hoisting and travelling speeds.
E-Control
The very robust brass valve distinguishes the E-control. The orientated design results in easy of handling. Only available in single speed control.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
71“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsControls for JDN M-Series
DS Control
The operating air is connected to the hand control valve. A built-in pressureregulator prevents overload to the hoist in case of inadmissibly high pressure. The motor connection housing of the DS control includes an oiler which automatically stops the oil flow when the hoist comes to a standstill.
An additional advantage: the oiler is situated directly around the motor. The operating air immediately feeds to the motor when the hand lever is actuated. The hand lever is spring loaded and returns automatically to the zero position when released. This forced release serves also as an emergency stop. The DS control is for two-hand operation and it is available for all air hoists of the “B” and “M” series.
PS Control
The PS control is an alternative for the DS control, being a single hand usecontroller for the M-series hoists.
Controls for JDN Air Hoists with Motor Trolley and JDN Monorail Hoists
For controlling JDN air hoists with motorised trolleys and JDN monorail hoists we recommend the four button version E or F - Control. The rope control option is also available.
Controls for JDN Air Cranes
For controlling JDN air cranes the F-control is the most suitable due to its multi-function capability.
Operating convenience via Radio Control
To overcome excessive distances between operator and crane, or to remotely use hoisting equipment, the JDN Radio Control offers a convenient and safe alternative to other control types. The JDN Radio Control is also available in explosion proof design.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
722015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
JDN Subsea Hoists
J.D. Neuhaus have been writing hoist technology history for over 260 years through consistent product innovations. Today, JDN air hoists are used in more than 70 different industries in over 90 different countries. That the expertise of JDN goes beyond the border is proven by their latest technology in SubSea hoisting, of which the world launch was hosted in Australia. The new JDN PROFI SubSea series are developed to be used in complex underwater lifting operations; using variable speed control and overload protection with an operating depth of up to 70m in water. JDN offer air and hydraulic options, in capacities of 3 to 6 tonnes.
Features
• Manufactured in Germany, under strict quality control with demanding tolerances.
• All JDN models are manufactured to comply with AS1418.2.
• Available with air or hydraulic operation.
• Variable speed control.
• Supplied with overload protection.
• Design for water operating depth of up to 70m.
• For both horizontal and oblique use.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
73“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsHoists & Trolley Model 3TI - SUBSEA 6TI - SUBSEA
Stock Code JDN737 JDN767
Rated Capacity (tonne) 3.2 6.3
Weight with standard 3m lift (kg) 150 161.5
Motor Output (kW) 3 3
Chain Dimension (mm) 13 x 36 13 x 36
No. of Chain Strands 1 2
Air Pressure (bar) 6 6
Air Consumption at full load (m3/min) LiftingLowering
45.5
45.5
Air Connection G1 G1
Lifting speed at full load (m/min) 2.3 1.2
Lowering speed at full load (m/min) 5.4 2.7
Length of Control at standard lift (m) 2 2
Max. water depth (m) 552 552
Specifications
Dimensions (in mm)
Model 3TI - SUBSEA 6TI - SUBSEA
A 593 674
B 373 454
C1 300 300
C2 455 455
D 755 755
E1 40 40
E2 30 40
F 187 154
G 233 233
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
742015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Electric Wire Rope Hoists
The Pacific Electric Wire Rope Hoists are suited for a wide range of applications such as warehouses, construction sites and factories. Due to its compact and lightweight design, it is perfect for when easy installation and quick use is needed.
Features
Automatic upper limit switch; when rope disc touches the limit arm,hoisting is automatically stopped.
Dynamic and mechanical brake providing instant and safe braking.
Convenient 240V / single phase power supply.
Sensor arm automatically activates lower limit switch to stop motorif rope is under wound.
Supplied with 3m power lead and industry plug & 10m heavy dutyIP65 waterproof pendant control.
Wire rope with 360º weighted hook with safety latch.
Optional push trolley mount CRH0720.
Optional mounting arm CRH0710 (not available for CWS300).
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
75“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsModel CWS80 CWS160 CWS230 CWS300
Stock Code CWS080 CWS160 CWS230 CWS300
Rated Capacity (kg) 80 160 230 300
Speed (m/min / 50Hz) 30 22 14 13
Motor Output (kW) 0.8 1.2 1.3 1.5
Power Supply 240 1Ø 50 Hz
Max. Height of Lift (m) 35 40 24 24
Wire Rope Dimension (Ø mmxm) 3.3 x 36 4.0 x 41 5.0 x 25 4.8 x 25
Net Weight (kg) 9 14 15 17
Specifications
Optional Attachments
Model CRH0710 CRH0720 CRH0720A
Stock Code CRH071 666110 666111
Description Swivel arm assembly Trolley mount bracket to fit hoist to PPT105 push trolley.
Suitable for CWS80
Trolley mount bracket to fit hoist to PPT105 push trolley.
Suitable for CWS160/CWS230 / CWS300
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
762015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Dimensions
Model CWS80 CWS160 CWS230 CWS300
A 200 244 244 244
B 168 182 182 182
C Ø65 Ø60 Ø60 Ø60
D 605 640 640 640
E 879 879 879 879
1800 067 687
77“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
HoistsElectric Wire Rope Hoist
Austlift Electric Rope Hoist is lightweight and compact in design. For use on construction sites and suitable for a variety of applications such as Factories, Warehouses, production lines etc.
Features
• Dual capacities from 500kg to 1000kg.
• Fitted with overwind limit switch with dynamic braking system.
• Power supply of 240 volt/single phase with plug fitted ready for work.
• Pendant control has IP54 protection classification.
• Hoist can be fitted to motorized trolley or rotary mounting jib as option.
• All hoists are CE certified and comes with instruction manual and Test Certificate.
Model Configuration Volt (V) Imput Power (w)
WLL (kg) Lifting Spedd (m / min)
Lifting Height (m)
Package Size (cm)
G.W / N.W
144016 Single HookDouble Hook
240 1700 5001000
105
126
60x30x37 36 / 34
782015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Mini Wire Rope Hoist
Austlift Mini electrical wire rope hoist IP54 with safety devices are easy control of lifting for a wide range of application for warehouse, storage areas, factories, house areas, construction sites and plubings.
Features
• Light weight & Compact design.
• Automatic stop when rope touches limit arm.
• Dynamic brake designs for both static and dynamic loading.
Model 144051 144053
Rated Load (Kg) 150 250
Rated Volt(V) AC100-240 50/60Hz
Input Power(W) 780 1200
Wire rope Dia(mm) Ф3.8 Ф4.2
Lifting Speed(m/min) 15 12
Lifting Height(m) 20
G.W./N.W.(Kg) 28/27 30 / 29
Packing Size(mm) 425x365x370
1800 067 687
79“We have the right product, at the right price, when you need it, on-time, every time”
Hoists
www.keblestrading.com.au
Care & Safety Instructions forManual Hoists
Safety
Before Use
While in Operation
Moving heavy loads is hazardous. When lifting equipment is not used correctly or is poorly maintained, accidents and serious injury could result. The following safety precautions should be applied to the operation, maintenance and inspection of PWB Anchor manual hoist products.
• Read the owner’s manual and familiarise yourself with the safety instructions.• Never lift more than the capacity shown on the hoist name plate if the plate is missing, DO
NOT use the hoist.• Never operate a hoist if damaged or malfunctioning.• Check that the hook latches work properly and replace missing or broken hook latches.• Check if load chain is twisted, kinked, damaged or streched.• Check if hook is modified or deformed.• Never use a hoist in an explosive atmosphere.
• Never use a hoist for lifting, supporting or transporting people.• Never lift or transport loads over or near people.• Never support a load on the tip of the hook.• Always ensure that the load is properly seated in the hook.• Never use the hoist load chain as a sling.• Never swing a suspended load.
WARNINGIMPROPER use could result in death or serious injury
802015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Gear case and hand wheel cover resistant to external shocksBoth sides of the hoist are covered with a thick steel gear case and with a strengthened wheel cover. They have the ideal shape and rigidity to maintain bearing alignment and withstand external shock.
Double enclosureThe braking mechanism, which makes up the heart of the hoist, is enclosed in a double cover: the wheel and the brake covers. These protective covers not only keep out weather elements but also help to prevent mud and dust from entering internal mechanisms.
Double Pawl SpringIn case one of the pawl springs is damaged, the other maintains its function increasing reliability.
Mechanical brakeKITO’s dry type mechanical brake ensures strong reliable brake performance.
HooksSpecifically heat treated top and bottom hooks have enough strength and toughness for the job. The design of the bottom hook, with relatively large dimensions, makes it easy to stabilize a load in a proper position.
BearingsUse of ball and needle bearings remarkably increases mechanical efficiency and produces high output power with minimum manual input.
Stopper prevents excessive loweringStopper assembly prevents excessive lowering of a load and also keeps load chain from exiting. When you feel a noticeable increase in pull force to lower the load, you should realize that you cannot lower the load any further.
Load chain guideSmooth load chain movement is facilitated by having a chain guide mechanism in the flanged load sheave and guide roller.
GearsCompact, highly efficient and durable gears.
Grade 100 Load ChainThis component comprises the heart of the chain hoist, made of heat treated special steel alloy.
Kito Manual Chain Blocks10 key features of a “Kito Mighty Model M3” Chain Hoist
1800 067 687
81“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Chain BlocksKito Manual Chain Blocks
Capacity Part No. Headroom (mm)
Load Chain Dia (mm) x fall
Weight (Kg)
Load ChainDia x Pitch
(mm)
Load Chain Part No.
250Kg 45377 217 3.2 x 1 2.9 3.2 x 9 44835
The CX003 chain block has been designed with an integral aluminium body with a net weight of 2.4kg. With a rated load of 250kg, the CX003 is equipped with an overload limiter as standard.Available in standard lift height of 2.5 metres. Optional lift heights also available.
Standard features include:
• Wide internal diameter of hooks (top and bottom).• Smart body with non-protruding bolt.• Equipped with overload limiter.• High strength load chain.• Hook latch with tip supporting structure.
• Applications: Mining, engineering, construction
• Australian Standard: AS1418.2
» CX Series Chain Blocks
822015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
CapacityPart No. (3m Lift)
Part No. (6m Lift)
Headroom(mm)
CloseHeadroom
(mm)
Load Chain Dia (mm) x
fallWeight* (kg)
Load ChainDia x Pitch
(mm)
Load Chain
Part No.
M3 Series Chain Block
500kg 43269 47769 360 405 5.0 x 1 10.0 5.0 x 15 44863
1 tonne 43271 47444 410 440 6.3 x 1 11.5 6.3 x 19.1 46722
1.5 tonne 43273 46637 470 495 7.1 x 1 14.5 7.1 x 21 46731
2 tonne 43275 47882 500 520 8.0 x 1 21.0 8.0 x 24 44864
3 tonne 43277 47883 540 595 7.1 x 2 24.0 9.0 x 27 46731
5 tonne 43279 47884 640 720 9.0 x 2 41.0 9.0 x 27 46735
7.5 tonne 43281 63286 810 865 9.0 x 3 63.0 9.0 x 27 46735
10 tonne 49575 49577 780 890 9.0 x 4 83.0 9.0 x 27 46735
M3 Series Chain Block with overload limiter
500kg 63067 63109 360 405 5.0 x 1 10.0 5.0 x 15 44863
1 tonne 63068 63063 410 440 6.3 x 1 11.5 6.3 x 19.1 46722
2 tonne 63069 63064 500 520 8.0 x 1 21.0 7.1 x 21 44864
3 tonne 63070 63065 540 595 7.1 x 2 24.0 7.1 x 21 46731
5 tonne 63071 63066 640 720 9.0 x 2 41.0 7.1 x 21 46735
10 tonne 64659 64302 730 890 9.0 x 4 83 9.0 x 27 46735
M3 Series chain blocks are designed for maximum durability and safety in continuous heavy duty applications. Available in standard lift heights of 3 and 6 metres, these premium units can also be close coupled to PWB Anchor push and geared trolleys. Optional lift heights also available.
*Weights shown for Chain Blocks are for standard 3 metre lift models
• Applications: Mining, engineering, construction
• Australian Standard: AS1418.2
» M3 Series Chain Blocks
1800 067 687
83“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Chain BlocksAnchor Manual Chain Blocks
C Series Chain Blocks
» Standard features include:
• Compact size and lightweight body.
• Strong robust steel construction.
• Suitable for Rigging and Construction applications.
• Applications: Manufacturing, construction and mining
• Australian Standard: AS1418.2
PWB Anchor’s C Series Chain Blocks have displayed their strength and reliability in industry over many years. They are a cost effective choice, designed to meet demanding applications. Optional lift heights also available.
CapacityPart No. (3m Lift)
Part No. (6m Lift)
Headroom(mm)
Load Chain Dia (mm) x
fallWeight* (kg)
Load ChainDia x Pitch
(mm)
Load Chain
Part No.
500kg 48188 48190 295 5.0 x 1 8.0 5.0 x 15 46719
1 tonne 48191 48193 340 6.3 x 1 12.5 6.3 x 19.1 46722
2 tonne 48487 48489 480 10.0 x 1 28.0 10 x 30 46726
3 tonne 48491 48493 550 8 x 2 25.0 8.0 x 24 46734
5 tonne 48495 48497 690 10.0 x 2 39.0 10 x 30 46726
10 tonne 48499 48500 920 10.0 x 4 78.0 10 x 30 46726
20 tonne 48581 63654 1040 10.0 x 8 168.0 10 x 30 46726
*Weights shown for Chain Blocks are for standard 3 metre lift models.
842015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Mini II Chain Blocks
• Applications: Mining, construction, engineering, entertainment
• Australian Standard: AS1418.2
The lightweight PWB Anchor Mini II Chain Block is a general purpose, compact unit, designed for a wide range of lighter applications.Available in standard lift heights of 3 and 6 metres.
CapacityPart No. (3m Lift)
Part No. (6m Lift)
Headroom(mm)
Load Chain Dia (mm) x
fallWeight* (kg)
Load ChainDia x Pitch
(mm)
Load Chain
Part No.
500kg 43681 43683 295 5.0 x 1 7.5 5.0 x 15 43748
1 tonne 43685 43687 330 6.3 x 1 11.0 6.3 x 19.1 43749
2 tonne 43689 43691 455 9.0 x 1 24.0 9.0 x 27 43750
*Weights shown for Chain Blocks are for standard 3 metre lift models.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
85“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Chain BlocksVital Chain Blocks
Features
Vital is a Japanese brand which is globally recognised for their high quality products. Their range of chain blocks are suited for many applications in the mining, construction, industrial and automotive industry. They have proven to be an economical method to lift heavy loads with ease. The capacities vary from 0.5 tonne to 20 tonne and all chain blocks can be supplied with overload protection for added security of use.
• Manufactured in Japan using optimum high quality steel which conforms to the strict JIS & ISO regulations.
• All Vital models are manufactured to comply with AS1418.2.
• Designed for long-term use while providing the lowest possible per-use cost.
• Can be supplied close coupled and extra close coupled to girder trolleys to alleviate headroom restrictions.
• All Vital chain blocks can be supplied with overload protection.
• Customised lift height are available upon request.
• Quality caged needle bearings on load sheave and thrust bearings on bottom hook.
• Hardened alloy steel load chain with embossed identification, marked as to the relevant standards.
• Load chain exceeds Australian Standards with 5:1 Safety Factor.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
862015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model 05VH5 10VH5 15VH5 20VH5 30VH5 50VH5 75VH5 90VH5 92VH5 93VH5
Stock Code VCB050 VCB100 VCB150 VCB200 VCB300 VCB500 VCB750 VCB910 VCB915 VCB920
Rated Capacity (tonne) 0.5 1.0 1.5 2.0 3.0 5.0 7.5 10.0 15.0 20.0
Standard Lift Height (m) 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0
Pull to lift load (kg) 25 33 34 34 35 39 41 41 41 X 2 41 X 2
Net Weight (kg) 8.6 11.5 13.8 21.6 23.0 41.0 60.5 78.0 150.0 190.0
Model 05VHS 10VHS 15VHS 20VHS 30VHS 50VHS 75VHS 90VHS 92VHS 93VHS
A 127 147 147 179 147 179 179 179 207 207
B 144 157 174 204 206 263 345 367 745 873
C 305 345 370 425 505 635 740 760 850 870
D 27 30 34 37 43 47 67 67 87 87
Specifications
Dimmensions (in mm)
*Vital chain blocks with customised lift heights are available
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
87“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Chain BlocksPacific Chain Blocks with Optional Overload Protection
Features
• All Pacific models are manufactured to comply with AS1418.2.
• High strength end stop with secondary end anchor for increased safety.
• “T” type hooks for improved load holding integrity (except for the 250kg capacity).
• Gear system design for reduced effort when lifting loads.
• Includes a specially designed hand wheel to eliminate hand chain slippage and pocket wear.
• Encapsulated needle bearings and side plate bearings for smoother operation.
• Brake lockout bearing for security of braking mechanism.
• Key internal components are CNC machined before being heat-treated and toughened.
• Fitted with high quality European zinc plated Grade 80 load chain.
• No aluminum content which ensures suitability for mining applications.
• Overall better design and improved finish to prolong life expectancy.
• All models available with a patented Overload Limiting device (except for the 250kg capacity).
• Now available with a complimentary display stand when purchasing a product stock package.
Pacific Chain Blocks feature better quality in a new compact design. The extensive range is suitable for many applications in the mining, construction, industrial and automotive industry. A patented Overload Limiting device is available for all sizes (except for 250kg capacity) to improve safety. These chain blocks have it all; better quality, easy to use, improved safety and all of this with reduced cost.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
882015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Capacity 250 KG 500 KG 1 TONNE 1.5 TONNE 2 TONNE 3 TONNE 5 TONNE 10 TONNE
Stock Code PCB 301 302 303 306 313 316 318 319 323 326 333 336 353 356 359 360
Lift Height (m) 3 6 3 6 3 6 3 6 3 6 3 6 3 6 3 6
Test Load (kg) 375 750 1500 2250 3000 4500 7500 15000
Effort to lift full load (N)
190 210 285 325 355 340 400 540
No. of Falls 1 1 1 1 1 2 2 4
Hand Chain (mm x mm)
Ø5 x 23.7
Hand Chain Drop (m)
2 5 2 5 2 5 2 5 2 5 2 5 2 5 2 5
Load Chain (mm x mm)
Ø4 x 12 Ø5 x 15 Ø6.3 x 19 Ø7.1 x 21 Ø8 x 24 Ø7.1 x 21 Ø9 x 27 Ø9 x 27
Net Weight for 3m lift (kg)
6 9 12 14 20 23 39 65
Stock Code with O/L PCB
301L 302L 303L 306L 313L 316L 318L 319L 323L 326L 333L 336L 353L 356L 359L 360L
Specifications
*Pacific chain blocks with customised lift heights are available
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
89“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Chain Blocks
Capacity 250 KG 500 KG 1 TONNE 1.5 TONNE 2 TONNE 3 TONNE 6 TONNE 10 TONNE
A 106 128 142 158 175 158 183 195
B 68 75 76 80 88 80 90 95
C 108 130 150 170 185 220 225 355
D 280 280 330 360 385 510 615 810
E 20 22 26 29 35 37 43 47
F Ø18 Ø20 Ø25 Ø30 Ø33 Ø36 Ø43 Ø44
Dimmensions (in mm)
902015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
» Chain Block (W3 Series)
• Austlift industrial Grade W-3 series manually operated Chain Blocks are used for general hoisting operation such as mining, construction, industrial lifting and domestic applications.
• Rated capacities from 250kg to 20 tonne.
• Standard height of lift is 3 and 6 metre.
• Other height of lift available upon request. Manufactured for ease of operation, and light weight in design.
• Robust, durable and compact in construction.
• All blocks come with ball bearing Swivel Hook. Individually serial numbered with Test Certificate and instruction manual supplied.
• Conforms to AS1418.2 standards.
W3 Series
1800 067 687
91“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Chain Blocks
3M Chain Code
6M Chain Code
WLL (T)Test
Load (T)
Pulling Effort (Kg)
Load Chain Size (mm)
No. of chain falls
Net Weight
(Kg)
Extra Weight/M Extra Lift
(Kg)
Packaging Dimensions
(cm)
111002 - 0.25 0.32 ≤25 4 1 3 1.5 22x17x23
111005 111505 0.5 0.63 ≤27 5 1 8.2 1.5 22x17x23
111010 111510 1 1.25 ≤31.5 6 1 11.3 1.8 24x18x23
111015 111515 1.5 1.88 ≤36 7.1 1 13.2 2 26x18x26
111020 111520 2 2.5 ≤40 8 1 21.3 2.7 32x20x29
111025 111525 3 3.75 ≤47.5 7.1 2 21.7 3.2 31x18x33
111030 111530 5 7.5 ≤48 9 2 39.7 5.3 40x20x36
111035 111535 10 12.5 ≤49.5 9 4 66 9.8 54x50x31
111040 111540 15 18.75 ≤45.6 10 6 95 14.2 55x60x40
111045 111542 20 25 ≤44.7 10 8 155 23.9 60x70x50
* Other chain length available.(111541 15Tx10M, 111544 20Tx9M.)
Dimensions
3M Chain Code
6M Chain Code
WLL Tonne
A mm
B mm
C mm
D mm
E mm
H MINI mm
111002 - 0.25 95 97 27 27 18 230
111005 111505 0.5 140 131 60 33 31 312
111010 111510 1 156 151 61 31 33 360
111015 111515 1.5 176 151 60 44 38 385
111020 111520 2 223 183 67 58 40 430
111025 111525 3 223 151 106 85 44 490
111030 111530 5 252 183 133 64 49 675
111035 111535 10 380 183 263 88 64 880
111040 111540 15 420 230 310 95 80 950
111045 111542 20 480 320 580 100 95 1075
Please check operation manual for more details
922015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
1800 067 687
93“We have the right product, at the right price, when you need it, on-time, every time”
Lever Hoists
www.keblestrading.com.au
Kito Lever Hoists
The L5 series lever hoist offers one of the largest range of capacities on the market.Lightweight, compact and designed for heavy duty work in rigorous and demanding applications. All models feature the patented ‘free wheel safety brake mechanism’ and nickel plated load chain.Supplied in standard lift heights of 1.5 metres and 3 metre, with optional lift heights also available.L5 Series Lever Hoists have earned their position in industry providing strength, endurance and reliability across various applications.
Compact and light weightKito’s original technology has realised innovative size and weight reductions. Operability, portability and storage have become easier and more convenient.
Nickel plated chainThe nickel plated chain developed and manufactured by Kito has a high strength of 1000N/mm2. Besides strength, it is also excellent in both corrosion and wear resistance.
High strength frameThe frame is an integral structure made of carbon steel. For load bearing supports, induction hardening has been applied. The strength has also increased frame thickness.
Lever strength increaseLever strength (bending, torsion, and lever support) has been improved by reviewing the shape and the thickness of the lever.
Hook latchA hook latch has been designed to fix securely. The increase of the hook latch thickness has also resulted in greater resistance to deformation and damage.
Weight saving hookAlloy steel has been used for the hooks of LB025 to LB090. This has allowed weight saving without changing the overall size.
Reliable brake performanceA unique dry condition brake has been designed to have strong braking force.
Maintenance improvementCap nuts are used to tighten the gear case and brake cover. This allows maintenance to occur without damaging the screws.
Standard features of a Kito L5 Lever Block
» L5 Series Lever Hoists
942015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Complementing the Lever Hoist range are the lightweight LX003 and LX005 models. Compact and portable these 250kg and 500kg capacity units are an ideal lever hoist for lifting, lowering or positioning of loads and can be carried or stored in your toolbox. Optional lift heights also available.
» LX Series Lever Hoists
Capacity Part No. Lift Height (metres)
Headroom (mm)
Load Chain Dia (mm) x fall
Weight (Kg)
Load Chain Dia x Pitch
(mm)
Load Chain Part No.
250Kg 44200 1.0 205 3.2 x 1 1.6 3.2 x 9 44835
500kg 44201 1.2 246 4.3 x 1 2.6 3.2 x 12.0 44836
Standard features include:
• Compact and Light.
• Easy to carry and easy to use, even in tight quarters or in elevated work locations.
• Fasteners are designed to protect threads from damage making maintenance easier.
• Nickel plated chain.
• The hook latch is highly resistant to deformation and damage.
• Single-step reduction gear, requires manual fastening force and assured load holding. Reliable load fastening can be provided to the last click of the lever.
• LX003 comes complete with belt bag.
• Applications: Mining, engineering, construction
• Australian Standard: AS1418.2
1800 067 687
95“We have the right product, at the right price, when you need it, on-time, every time”
Lever Hoists
www.keblestrading.com.au
Available with overload limiter for mining and offshore applications.
» L5 Lever Hoist
Standard features include:
• Unique patented ‘Free Wheeling Hub’ mechanism.
• Smaller, lighter, high grade (solid), alloy steel frame construction.
• Double brake pads with four braking surfaces.
• Low headroom design.
• Double Pawl & Double Spring Assemblies.
• Nickel plated grade 100 load chain.
• Needle and Ball roller bearings allow maximum mechanical efficiency with minimum effort.
• Applications: Mining, construction, engineering, entertainment
• Australian Standard: AS1418.2
962015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Capacity Part No.(1.5m Lift)
Part No.(3m Lift)
Headroom (mm)
Lever Lenght (mm)
Load Chain Dia (mm) x fall
Weight (Kg)
Load Chain Dia x Pitch
(mm)
Load Chain
Part No.
L5 Lever Block
800Kg 44202 45890 280 245 5.6 x 1 5.7 5.6 x 15.7 44278
1 tonne 44203 62575 300 245 5.6 x 1 5.9 5.6 x 15.7 44278
1.6 tonne 44204 45891 335 265 7.1 x 1 8.0 7.1 x 19.9 44279
2.5 tonne 44205 61917 375 265 8.8 x 1 11.2 8.8 x 24.6 44280
3.2 tonne 44206 45892 395 415 10.0 x 1 15.0 10 x 28.0 44281
6.3 tonne 44207 45893 540 415 10.0 x 2 26.0 10 x 28.0 44281
9 tonne 44208 61498 680 415 10.0 x 3 40.0 10 x 28.0 44281
L5 Lever Block with overload limiter
800Kg 63090 64934 280 245 5.6 x 1 6.0 5.6 x 15.7 44278
1 tonne 63091 64935 300 245 5.6 x 1 6.2 5.6 x 15.7 44278
1.6 tonne 63092 64936 335 265 7.1 x 1 8.4 7.1 x 19.9 44279
2.5 tonne 63093 64937 375 265 8.8 x 1 11.6 8.8 x 24.6 44280
3.2 tonne 63094 64938 395 415 10 x 1 15.2 10 x 28.0 44281
6.3 tonne 63095 64939 540 415 10 x 2 26.2 10 x 28.0 44281
9 tonne 63096 64940 680 415 10 x 3 40.2 10 x 28.0 44281
*Weights shown for Lever Hoists are for standard 1.5 metre lift models.
1800 067 687
97“We have the right product, at the right price, when you need it, on-time, every time”
Lever Hoists
www.keblestrading.com.au
The CM Puller is a lightweight tool that lifts or pulls with minimum effort. The puller has almost unlimited applications as it can pull or lift in the vertical or horizontal position or at any angle.Overload protection is available as an optional extra.
» CM Puller
Standard features include:
• Designed for heavy-duty construction and industrial applications.• Aluminium alloy construction, weather proofing and powder coat finish.• Corrosion resistant.
• Applications: Manufacturing, construction and mining
• Australian Standard: AS1418.2
CM Pullers & Riggers
Capacity Part No.(1.5m Lift)
Headroom (mm)
Level Length(mm)
Load Chain Dia (mm) x fall
Weight (Kg)
Load Chain Dia x Pitch
(mm)
Load Chain Part No.
750Kg 45036 273 540 6.1 x 1 6.3 6.3 x 19.1 46722
1.5tonne 45041 362 540 7.9 x 1 10.9 7.9 x 21.8 46747
3 tonne 45046 432 540 7.9 x 2 20.0 7.9 x 21.8 46747
6 tonne 45049 543 540 7.9 x 4 29.5 7.9 x 21.8 46747
982015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
The CM Rigger is designed to handle the rated capacity with minimal effort. Its lightweight, non-kinking, flexible load chain makes the rigger extremely easy to operate. This simple design assures low maintenance, with no special tools required. Hooks are forged steel, heat treated and both top and bottom hooks swivel easily through a full 3600.
» CM Rigger
Standard features include:
• Lightweight and compact.• Designed for light industrial lifting and pulling applications.• Easily stored in a tool box.
• Applications: Manufacturing, construction and mining
• Australian Standard: AS1418.2
Capacity Part No.(1.5m Lift)
Headroom (mm)
Level Length(mm)
Load Chain Dia (mm) x fall
Weight (Kg)
Load Chain Dia x Pitch
(mm)
Load Chain Part No.
700Kg 43194 273 540 4.7 x 1 3.4 4.7 x 14.2 46754
1400kg 43195 318 540 4.7 x 2 5.7 4.7 x 14.2 46754
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
99“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Lever HoistsVital Lever Blocks NR-2 Series
Features
• Manufactured in Japan using optimum high quality steel which conforms to the strict JIS & ISO regulations.
• All Vital models are manufactured to comply with AS1418.2.
• One-touch operation for free chain adjustment.
• Vital lever blocks can be supplied with overload protection for added security of use (excluding 250kg and 500kg models).
• The unique design of the bottom hook prevents slipping and ensures safe operation.
• Hardened alloy steel load chain with embossed identification, marked to the relevant standards.
• Load Chain Exceeds Australian Standards with 5:1 Safety Factor.
• Minimum load requirement of up to 10% of the Working Load Limit to ensure the operation of the braking system. E.g. a 1.5 tonne lever block requires a minimum load of 150kg.
• Light loading; not suitable for tandem operations. If one of the lever blocks used in the tandem experiences an increase in the shared load and the other is reduced below the minimum load, inoperative breaks may occur and this could cause for the load to fall. For these applications we recommend the Vital Lever Blocks VR-2 series
Vital is a Japanese brand which is globally recognised for their high quality products. The NR-series lever blocks feature the “free-wheeling” braking system which enables fast and easy operation. There is a minimum load requirement of 10% of the Working Load Limit to ensure that the braking system remains operative and continues to support the load. These lever blocks are ideally suited for the shipbuilding, construction, mining and power transmission industries.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1002015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model NR2-03 NR2-05 NR2-08 NR2-10 NR2-15 NR2-30 NR2-60 NR2-90
Stock Code VLB202 VLB205 VLB207 VLB210 VLB215 VLB230 VLB260 VLB290
Rated Capacity (tonne) 0.25 0.5 0.8 1.0 1.6 3.2 6.3 9.0
Standard Lift Height (m) 1.0 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Pull to lift load (kg) 30 34 21 23 27 38 39 40
Net Weight (kg) 1.9 3.5 6.0 7.2 9.8 16.6 27.0 47.3
Chain Size (mm) 4.0 5.0 5.6 6.3 7.1 9.0 9.0 9.0
No. of Falls 1 1 1 1 1 1 2 3
Model NR2-03 NR2-05 NR2-08 NR2-10 NR2-15 NR2-30 NR2-60 NR2-90
A 85 110 146 146 161 191 191 191
B 65 82 119 126 146 180 243 318
C 230 260 295 325 350 425 565 680
D 150 267 256 256 368 368 368 368
E 24 27 27 30 34 43 47 67
Specifications
Dimmensions (in mm)
*Vital lever blocks with customised lift heights are available.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
101“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Lever HoistsVital Lever Blocks VR-2 Series
Features
• Manufactured in Japan using optimum high quality steel which conforms to the strict JIS & ISO regulations.
• All Vital models are manufactured to comply with AS1418.2.
• Vital lever blocks can be supplied with overload protection for added security of use (excluding 250kg and 500kg models).
• The unique design of the bottom hook prevents slipping and ensures safe operation.
• Easy two-step operation to prevent accidental free-wheeling.
• Hardened alloy steel load chain with embossed identification, marked as to the relevant standards.
• Load Chain Exceeds Australian Standards with 5:1 Safety Factor.
• The Vital VR-2 series are suitable for tandem lifting applications.
Vital is a Japanese brand which is globally recognised for their high quality products. The VR-series lever blocks feature a “lock-in and lock-out” braking system which is the more traditional style with a free- wheeling system requiring the disengagement of the gear drive mechanism which is impossible with any load suspended on it. These lever blocks are ideally suited for the (underground) mining, aerospace and energy industries.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1022015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model VR2-08 VR2-15 VR2-30 VR2-60
Stock Code VLB107 VLB115 VLB130 VLB160
Rated Capacity (tonne) 0.8 1.6 3.2 6.3
Standard Lift Height (m) 1.5 1.5 1.5 1.5
Pull to lift load (kg) 15 18 38 39
Net Weight (kg) 6.9 9.7 16.3 26.7
Chain Size (mm) 6.3 7.1 9.0 9.0
No. of Falls 1 1 1 2
Model VR2-08 VR2-15 VR2-30 VR2-60
A 148 163 191 191
B 128 148 181 244
C 295 355 405 550
D 260 370 370 370
E 27 34 43 47
Specifications
Dimmensions (in mm)
*Vital lever blocks with customised lift heights are available.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
103“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Lever HoistsPacific Lever Blocks with Optional Overload ProtectionThe extensive range of Pacific Lever Blocks feature superior quality at an affordable price. They are suitable for applications in the mining, construction, transport and automotive industry. A patented Overload Limiting device is available to improve safety (except for 250kg capacity).
Features
• All Pacific models are manufactured to comply with AS1418.2.
• “T” type hooks for improved load holding integrity (except for the 250kg capacity).
• New design double pawl safety springs to eliminate sticking
• New style cast hand wheel for added strength and durability
• Encapsulated needle bearings and side plate bearings for smoother operation.
• Brake lockout bearing for security of braking mechanism.
• All Pacific lever blocks can be supplied with overload protection (except 250kg).
• Key internal components are CNC machined before being heat- treated and toughened.
• Fitted with high quality European zinc plated Grade 80 load chain.
• No aluminum content which ensures suitability for mining• applications.
• Overall better design and improved finish to prolong life expectancy.
• Now available with a complimentary display stand when purchasing a product stock package.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1042015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Capacity 250Kg 500 Kg 800 Kg 1.6 Tonne 3.2 Tonne 6.3 Tonne
A 100 143 147 173 200 200
B 70 85 87 99 112 112
C 86 118 132 145 198 230
D 235 310 340 400 520 640
E 168 253 273 378 418 418
F 20 22 26 29 37 43
G Ø18 Ø20 Ø25 Ø30 Ø36 Ø43
Capacity 250Kg 500 Kg 800 Kg 1.6 Tonne 3.2 Tonne 6.3 Tonne
Stock Code PLB302 PLB305 PLB308 PLB316 PLB332 PLB363
Lift Height (m) 1.5 1.5 1.5 1.5 1.5 1.5
Test Load (kg) 375 750 1200 2400 4800 9450
Effort to lift full load (N) 115 248 285 315 360 370
No. of Falls 1 1 1 1 1 2
Load Chain (mmxmm) Ø4x12 Ø5x15 Ø5.6x17 Ø7.1x21 Ø10x28 Ø10x28
Length of lever handle (D)(mm) 168 253 273 378 418 418
Net Weight for 1.5m lift (kg) 1.86 4.42 5.71 9.27 16.50 21.29
Stock Code with O/L N/A PLB305L PLB308L PLB316L PLB332L PLB363L
Specifications
Dimensions (in mm)
*Pacific lever blocks with customised lift heights are available
1800 067 687
105“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Lever Hoists
Austlift L-3 series Lever Blocks are used for general hoisting in the mining, construction, industrial and domestic situations. Commonly used for short lifts and pulling applications.
» Lever Block (L3 Series)
• Rated capacities available 250kg to 9 tonnes.
• Standard height of lift 1.5 or 3 metre except for 250kg which has 1 metre lift, Other lift height available upon request.
• Robust, durable, portable and compact in construction.
• All Lever Blocks come with ball bearing Swivel Hook.
• Test Certificate and instruction manual supplied.
• Conforms to AS1418.2 standards.
WLL 0.25T 0.5T 0.75T 1T 1.5T 3T 6T 9T
CODE 121002 121005 /121305
121010 /121310
121015 /121315
121020 /121320
121025 /121325
121030 /121330
121035 /121335
Lift Length (m) 1 1.5 / 3 1.5 / 3 1.5 / 3 1.5 / 3 1.5 / 3 1.5 / 3 1.5 / 3
Test Load (T) 0.38 0.75 1.12 1.5 2.25 4.5 9 13.5
Effects required At capacity, (N)
217 303 140 185 234 363 370 375
Lifting Chain Size (mm) 4 5 6.3 6.3 7.1 9 9x2 9x3
Min Hook to Hook: C (mm)
205 260 295 295 335 450 542 645
Head Room: B (mm) 75 82 128 128 148 181 232 366
Head RoomL: A (mm) 92 110 152 152 175 195 195 195
Handle size: D (mm) 153 251 256 256 368 368 368 368
Net weight (kg) 1.85 3.5 7.0 7.2 11 20 28 43
Please check operation manual for more details. Longer Chain Lengths are available upon request.
1062015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Girder Trolleys
Geared Trolley
Designed to travel along rolled steel joists, universal beams and universal columns. Suits a variety of beam widths. 2.5 metre standard drop hand chain (optional lengths available on request).
• Applications: Construction, manufacturing, mining and general engineering. • Australian Standard: AS 1418.2
1800 067 687
107“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Trolley
CapacityBeam Range (mm)
Part No. Weight
(kg)Headroom
*H (mm)
Wheel Dia. Running
surface D (mm)
Min. Radius
(m)A (mm) C (mm) L (mm)
M (mm)
N2 (mm)
Hand chain size
Hang P in Dia
(B)
Single Hanger Pin Trolley - Standard Beam
1 tonne 64-210 49183 20 136 88 0.9 102 352 274 120 22/22 5 30
2 tonne 89-210 49184 30 155 100 1.5 117 371 310 120 22/22 5 36
3/4 tonne 102-210 49185 54 200 130 1.8 145 411 376 166 28/28 5 48
5/6 tonne
114-210 49187 86 252 155 2.4 173 437 460 166 28/28 5 56
Single Hanger Pin Trolley - Wide Beam
1 tonne 210-268 63697 25 136 88 0.9 102 423 214 120 22/22 5 30
1 tonne 268-330 61605 28 136 88 0.9 102 488 214 120 22/22 5 30
2 tonne 210-268 44102 32 155 100 1.5 117 439 310 120 22/22 5 36
2 tonne 268-330 63698 35 155 100 1.5 117 505 310 120 22/22 5 36
3 tonne 210-268 49186 70 200 130 1.8 145 489 376 166 28/28 5 48
3 tonne 268-330 62318 82 200 130 1.8 145 553 376 166 28/28 5 48
5 tonne 210-268 49188 97 252 155 2.4 173 515 460 166 28/28 5 56
5 tonne 268-330 49625 102 252 155 2.4 173 579 460 166 28/28 5 56
Dual Hanger Pin Trolley
10 tonne 127-210 49189 175 288 195 3.7 214 468 544 218 36/36 6,3 56
10 tonne 210-330 64124 205 288 195 3.7 214 583 544 218 36/36 6,3 56
20 tonne 210-330 64125 355 270 195 N/A Dimensions available on request
*Running surface of track wheel to hooking surface of hanger plate
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1082015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Series 1 Girder Trolleys
Pacific Series 1 Girder Trolleys feature a strongly constructed, fully adjustable trolley which is designed to fit the flanges of both tapered and parallel beams. They are available as push or geared variety and comply with all relevant Australian Standards.
Features
• All Pacific girder trolleys are manufactured to comply with AS1418.2.
• Choose from either push or hand-geared travel.
• Twin pin configuration provides closer headroom than single pin variety.
• Available to suit larger beam widths on request.
• Fitted with anti-drop plates for improved safety and compliance.
• Can be supplied close coupled to suit most Pacific Hoists.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
109“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleySpecifications
Pacific Series 1 Girder Trolleys (GEARED)
Pacific Series 1 Girder Trolleys (GEARED)
Model PGT110 PGT120 PGT130 PGT150 PGT160
Stock Code PGT110 PGT120 PGT130 PG150 PGT160
Rated Capacity (kg) 1000 2000 3000 5000 10,000
Beam width (mm) 76 - 204 90 - 216 126 - 210 126 - 210 125 - 310
Min. curve radius (m) 1.0 1.5 1.7 1.7 2.7
Net Weight (kg) 15.08 24.44 40.30 42.10 131.0
Gross Weight (kg) 15.75 25.32 41.64 43.50 148.0
*Additional beam width available on request.
Model PGT110 PGT120 PGT130 PGT150 PGT160
A 238 303 332 332 399
B 206 212.5 210.5 210.5 335.5
C 153 164 176 179 253.5
D 87 117.5 131 131 167
E 69 83 125.5 125.5 172
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1102015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Girder Trolleys
Pacific Girder Trolleys feature high quality construction for an economical price. They are available in either a push or geared variety and comply with all relevant Australian Standards.
Features
• All Pacific girder trolleys are manufactured to comply with AS1418.2.
• Fully adjustable to suit various beam widths.
• Fitted with anti-drop plates for improved safety and compliance.
• High-grade, fully sealed bearings for maintenance free extended life.
• Available with either push or hand geared travel.
• Anti-drop plates as standard for improved safety and compliance.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
111“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleySpecifications
Pacific Series 1 Girder Trolleys (GEARED)
Model PGT305 PGT310 PGT320 PGT330 PGT350 PGT360
Stock Code PGT305 PGT310 PGT320 PGT330 PGT350 PGT360
Rate Capacity (kg) 500 1000 2000 3000 5000 10000
Pin Configuration Single Single Single Single Single Twin
Min. Radius of curve (m) 0.8 1.0 1.1 1.3 1.4 2.0
Net Weight (kg) 10.5 14.5 21.5 31.0 46.0 91.0
Model PGT305 PGT310 PGT320 PGT330 PGT350 PGT360
A 223 270 300 356 405 485
B 188 224 261 308 354 395
C 32 40 52 62 75 110
D 24 30 38 40 50 70
E 273 341 349 362 374 501
F 50 - 152 64 - 203 88 -203 100 - 203 114 - 203 124 - 305
G 1.5 - 3
H 105 126.5 146 169 197 188
I 31 38 36 40 42 40
Pacific Girder Trolleys (GEARED)
1122015 EDITION Campbellfield
Tel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Geared Trolley
The Austlift Geared Trolley is hand-operated by pulling the hand-chain, running on the bottom flange of monorail. With a main shaft with spacers you can adjust the width of beam. They are widely used in Factories, Mines, Wharves, Docks, Warehouses and Engineering Workshops for installation of equipment and conveyance of goods. They are especially suitable for maintenance and repairing of equipment in places where no power supply is available.
Features
• Standard hand chain is 3 metres however longer chain lengths are available.
• High quality sealed ball bearings.
• Identification tag with serial number.
• Proof tested to 2 x WLL with certificate.
• Fitted with anti-drop plates for safety.
• Low headroom by design.
• Complies to AS1418.2.
Code WLL Beam Size Pulling Force*
Wt. Dimensions
A B C H
ton mm mm kg mm
131505 1 64 - 203 50N 14 287 236 211 115
131510 1.5 - 2 76 - 210 90N 16 305 273 236 130
131515 3 100 - 305 95N 24 420 320 295 164
131520 5 100 - 305 140N 36 426 366 334 177
131530 10 125 - 305 240N 90 450 389 460 237
*Pulling force is measured when the trolley is in full load.
1800 067 687
113“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleyGirder Trolleys
Push Trolley
Designed to travel along rolled steel joists, universal beams and universal columns. Suits a variety of beam widths.
• Applications: Construction, manufacturing, entertainment, mining and general engineering • Australian Standard: AS 1418.2
1142015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
CapacityBeam
Range (mm)Part No.
Weight (kg)
Headroom*H (mm)
Wheel Dia. Running
surface D (mm)
Min. Radius
(m)A (mm) C (mm) L (mm)
N1 (mm)
Hang P in Dia (B)
Single Hanger Pin Trolley - Standard Beam
250 kg 32 - 51 44439 3 86 48 0.9 54 116 178 10/10 16
500 kg 64 - 152 49175 7 110 58 0.9 70 256 216 14/14 25
1 tonne 64 - 210 49176 16 136 88 0.9 102 328 274 14/14 30
2 tonne 89 - 210 49177 24 155 100 1.5 117 350 310 14/14 36
3/4 tonne 102 - 210 49178 44 200 130 1.8 145 384 376 14/14 48
5/6 tonne 114 - 210 49180 74 252 155 2.4 173 414 460 16/16 56
Single Hanger Pin Trolley - Wide Beam
500 kg 64 - 210 49353 16 110 58 0.9 70 348 216 14/14 25
500 kg 210-268 49354 18 110 58 0.9 70 412 216 22/22 25
1 tonne 210-268 49355 18 136 88 0.9 102 423 274 22/22 30
1 tonne 268-330 49282 20 136 88 0.9 102 448 274 22/22 30
2 tonne 210-268 44103 27 155 100 1.5 117 439 310 22/22 36
2 tonne 268-330 44641 29 155 100 1.5 117 505 310 22/22 36
3 tonne 210-268 49179 52 200 130 1.8 145 489 376 28/28 48
3 tonne 268-330 49696 54 200 130 1.8 145 553 376 28/28 48
5 tonne 210-268 49181 85 252 155 2.4 173 515 460 28/28 56
5 tonne 268-330 49296 87 252 155 2.4 173 585 460 28/28 56
Dual Hanger Pin Trolley
10 tonne 127-210 49182 155 288 195 3.7 214 468 544 36/36 56
10 tonne 210-330 49760 170 288 195 3.7 214 583 544 36/36 56
*Running surface of track wheel to hooking surface of hanger plate
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
115“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleySpecifications
Pacific Series 1 Girder Trolleys (PUSH)
Model PPT105 PPT110 PPT120 PPT130 PPT150 PPT160
Stock Code PPT105 PPT110 PPT120 PPT130 PPT150 PPT160
Rate Capacity (kg) 500 1000 2000 3000 5000 10000
Beam width (mm) 62 - 172 76 - 204 90 - 216 126 - 210 126 - 210 125 - 310
Min. curve radius (m) 0.8 1.0 1.5 1.7 1.7 2.7
Net Weight (kg) 6.06 10.88 19.12 34.96 36.30 118.0
Gross Weight (kg) 6.4 11.32 19.88 36.22 36.70 133.0
*Additional beam width available on request.
Dimensions (in mm)
Pacific Series 1 Girder Trolleys (PUSH)
Model PPT105 PPT110 PPT120 PPT130 PPT150 PPT160
A 179 217 281 315 315 399
B 131 151 162 176 179 253.5
C 132 153 164 176 179 253.5
D 68 76 106.5 123 123 167
E 51.5 69 83 125.5 125.5 172
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1162015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Specifications
Pacific Girder Trolleys (PUSH)
Model PPT305 PPT310 PPT320 PPT330 PPT350 PPT360
Stock Code PPT305 PPT310 PPT320 PPT330 PPT350 PPT360
Rate Capacity (kg) 500 1000 2000 3000 5000 10000
Pin Configuration Single Single Single Single Single Twin
Min. Radius of curve (m) 0.8 1.0 1.1 1.3 1.4 2.0
Net Weight (kg) 6.5 10.5 17.5 27.0 41.0 86.0
Dimensions (in mm)
Pacific Girder Trolleys (PUSH)
Model PPT305 PPT310 PPT320 PPT330 PPT350 PPT360
A 223 270 300 356 405 485
B 188 224 261 308 354 395
C 32 40 52 62 75 110
D 24 30 38 40 50 70
E 244 310 327 342 354 480
F 50 - 152 64 - 203 88 -203 100 - 203 114 - 203 124 - 305
G 1.5 - 3
H 105 126.5 146 169 197 188
I 31 38 36 40 42 40
1800 067 687
117“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleyPush Trolley
Austlift Plain Trolley is moved by pushing the load lifted by the trolley,running along a flange of a monorail. A main shaft with spacers you can adjust the width of UB/UC beam. They are widely used in Factories, Mines, Wharves, Docls, Warehouses and Engineering Workshops for installation of equipment in places where no power supply is available.
Features
• High quality sealed ball bearings.
• Identification tag with serial number
• Proof tested to 2 x WLL with certificate.
• Fitted with anti-drop plates for safety
• Low headroom by design.
• Complies to AS1418.2.
Code WLL Beam Size
Min. Radius of Curve
Wt.
A B C H
ton mm mm kg mm
131005 0.5 64 - 140 0.8 5.5 228 196 190 108
131010 1 64 - 203 0.9 8.9 300 236 211 115
131015 2 76 - 210 1.0 10.7 318 273 236 130
131020 3 100 - 305 1.2 24.3 420 320 295 164
131025 5 100 - 305 1.3 36.3 444 366 334 177
131030 10 125 - 305 2.0 83.3 468 389 460 237
1182015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Cast Iron Wheels
Trolley Wheels
The PWB Anchor range of single flanged plain trolley wheels are designed from 250kg to 10 tonne capacities (over 4 wheels).
Each wheel has a machine cut tread for smooth running on rolled steel joists, universal columns or universal beams. Supplied in high quality cast iron, these trolley wheels are complete with bearings, knurled, axle, nut, dust cover and circlip.
• Applications: engineering • Australian Standard: AS 1418.2
Capacity
(on 4 wheels)
Part No. D (mm)
A (mm)
B (mm)
C (mm)
W (mm) Thread
H (mm) L (mm) N (mm) P (mm) O (mm)
250 kg* 49476 48 5 14 60 M12 1.5 17 14 22 12
500 kg 49477 58 8 27 82 M20 3 27 22 30 20
1 tonne 49478 88 8 27 116 M20 3 27 22 30 20
2 tonne 49479 100 8 32 133 M24 3 33 25 33 24
3 tonne 49480 130 8 37 159 M30 3 40 30 36 30
5 tonne 49481 155 10 43 190 M36 3 49 35 45 36
10 tonne * 49482 195 12 48 232 M42 21 61 43 75 42
*non-knurled axle, supplied with sellok pin.
1800 067 687
119“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleyCast Iron WheelsHand Wheels
Manufactured from cast iron with an un-machined, solid boss, these hand chain wheels are easily identified by their pattern number and ANCHOR markings and are used in conjuction with the appropriate PWB Anchor Hand Chain.
• Applications: engineering.
D(mm)
Part No. Pattern Number A(mm)
B(mm)
Hand Chain Dia (mm)
Hand Chain Part No.
132 46342 463 31 32 5.0 40261
170 46338 425 34 25 5.6 46763
180 46328 294 45 25 6.3 46768
210 46343 378 76 27 6.3 46768
245 46330 257 63 33 6.3 46768
265 46339 433 63 33 6.3 46768
330 46331 405 63 38 6.3 46768
380 46333 406 70 38 6.3 46768
460 46335 204 70 38 6.3 46768
610 46336 280 80 64 6.3 46768
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1202015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Single Flange Trolley Wheels
The Pacific Single Flange Trolley Wheels are ideally suited for general machinery production, crane building, platforms, carriages and rail systems. They are designed to suit both parallel and tapered flanges and are available in different capacities from 500 kg to 10 tonne.
Features
• CNC machined from high quality 45# steel.
• Designed to suit both parallel and tapered flanges.
• Fully sealed ball bearings.
• Inclusive of dust cap and circlip.
• Supplied complete; with galvanised axle and nut.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
121“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleySpecifications
Model PTW005 PTW010 PTW020 PTW030 PTW050 PTW100
Rated Capacity on 4 wheels
500 kg 1 tonne 2 tonne 3 tonne 5 tonne 10 tonne
Rated Capacity per wheel 125 kg 250 kg 500 kg 750 kg 1.25 tonne 2.5 tonne
Weight (kg) 0.7 1 2.5 3.7 6.2 12.3
Model PTW005 PTW010 PTW020 PTW030 PTW050 PTW100
ØA 62 70 100 114 140 175
ØB 92 100 136 160 190 230
C 9 9 11 13 15 12
D 18 20 24 28 34 53
E 2 2 2 3 3 3.2
F M16 M20 M24 M30 M36 M48
G 30 35 45 50 60 70
Dimensions (in mm)
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1222015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Pipe Trolley
The Pacific Pipe Trolley is compact and lightweight, a general purpose unit and designed to suit 60mm O/S diameter pipe.
Features
• The Pacific pipe trolley is manufactured to comply with AS4991.
• Designed to suit 60mm outside diameter pipe.
• Compact and lightweight with powder coated finish.
Specifications
Model PPT203
Stock Code PPT203
Rate Capacity (kg) 300
Pipe Dieameter (mm) 60
Net Weight (kg) 2.5
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
123“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Trolley
Model PPT203
A 147.5
B 160
C 22
D 68
E 160
F 60
G 17
Dimensions (in mm)
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1242015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Self-Locking Beam Trolleys
The PacificSelf-Locking Beam Trolleys feature a robust design in accordance with Australian Standard AS1418.2. The spring assisted locking pin enables quick and easy installation which makes this trolley ideally suited for the rigging industry.
Features
• Designed and tested in accordance with Australian Standard AS1418.2.
• Quick and easy installation with no tools required.
• Suitable for a wide range of beam sizes.
• Inclusive of Inclusive of a spring assisted locking pin for safe and easy attachment to the beam.
• A cost-effective and time saving way of suspending loads.
• Ideal for the rigging industry.
Specifications
Model CLP250 CLP251 CLP250
Rated Capacity 3 tonne 6 tonne 10 tonne
Beam Size (mm) 76 - 230 100 - 305 120 - 305
Weight (kg) 21 32 47.5
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
125“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleyDimensions (in mm)
Model CLP250 CLP251 CLP252
A 380 500 600
B 280 296 310
C 126 126 131
D 253 290 290
E 170 170 170
H 82 88 113
J 30 40 54
K 32 38 43
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1262015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Adjustable Angle Clamps
Pacific Adjustable Angle Clamps are suitable for a wide range of angle sections and will prove to be a cost-effective way of suspending loads. They feature an adjustable locking pin for safe and easy attachment which makes them ideally suited for the rigging industry. All clamps are designed and tested in accordance with Australian Standard AS4991.
Features
• Designed and tested in accordance with Australian Standard
AS4991.
• Quick and easy installation with no tools required.
• Suitable for a wide range of angle sections.
• Inclusive of an adjustable locking pin for safe and easy
attachment.
• Features a V-type clamping jaw which secures the clamp to the
angle section.
• A cost-effective and time saving way of suspending loads.
• This clamp can be used as both an anchor and suspension
device.
• Ideal for the rigging industry.
Specifications
Model CLP253 CLP254 CLP255 CLP256
Rated Capacity 500 kg 1 tonne 1.5 tonne 3 tonne
Beam Size (mm) 38 - 101 38 - 101 50 - 152 101 - 203
Weight (kg) 4.0 4.5 11.0 21.5
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
127“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsDimensions (in mm)
Model CLP253 CLP254 CLP255 CLP256
A 4 6 8 10
B 69 69 99 99
C 70 70 107 107
D 96 96 98 98
E 206 206 270 343
G 15 15 19 25.4
H 258 258 346 490
J 16 16 20 20
K 38 - 101 38 - 101 50 -152 101 - 203
1282015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Precautions for the use of PWB Lifting ClampsImportant: Before using PWB Anchor Lifting Clamps be sure to read the instruction manual.
Checking loads before use
• Ascertain the weight of a load and its centre of gravity.
• When lifting a load longer than 1m, calculate the centre of gravity in the lateral (side to side) direction.
• Ensure the load is free of oil and water.
Use clamps suitable for the lift
• Select clamps according to the mechanism and capacity necessary for the lift.
• Use clamps within the specified capacity (maximum working load, opening size and material hardness).
• Do not lift loads that have a thickness less than 1/4 of the maximum clamp opening size.
• Match the clamp working load capacity to the weight of the load. A load should weigh at least 1/5 of the
working load weight of the clamp.
• When lifting loads where the surface is slippery (e.g oil, water etc.), remove the oil first and ensure that the
clamp teeth are in good condition.
• Select the appropriate clamp.
• When lifting diagonal materials, use a model SBB clamp and refer to the instructional manual for the correct
lifting procedure.
• When lifting long materials vertically (more than 10 times in length/width), use the model SBB Clamp and refer
to the instructional manual for the correct lifting procedure.
• Do not use clamps instead of hooks.
• Never use clamps that have been hit hard or had impact type loads placed on them.
1800 067 687
129“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsPrecautions when attaching clamps
• Determine the position to attach clamps so that the safety lock lever (or clutch) does not touch
the wire, chain, lifting shackle, or other objects when lifting or lowering.
• Ensure clamps are attached at a position higher than the centre of gravity of the object.
• Make sure the clamps are set close together on the load.
• Make sure that the safety lock (latch or lever) has been set securely.
• Always determine positions for attachment taking into account where the load will be set down.
General precautions
• Do not clamp steel plates from the side if they are to be raised vertically.
• When using many points for lifting, pay attention to unbalanced loads.
• When lifting heavy or long objects (more than 1m), ensure the lift is completed with 2 to 4 lifting clamps.
• Use only certified lifting wires and chains.
• Before lifting check for twists and kinks.
• Use clamps with the correct orientation.
• Do not lift several different objects using separate clamps suspended from one hook.
• Do not lift more than one steel plate with one clamp.
Precautions when lowering and setting down
• Anticipate the impact load where you will be lowering the object.
• Operate a crane slowly to reduce the chance of high impact on the clamps (loading shock).
• After removing clamps from objects ensure that they do not collide with each other.
1302015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Girder Trolleys and ClampsGirder Clamps
Featuring a single threaded adjustment pin for simple and easy installation, PWB Anchor Girder Clamps are supplied in a durable electrostatic enamel finish.
Note: Maximum headroom for narrowest beam width. Headroom decreases as beam width is increased.
• Applications: Construction, manufacturing, entertainment, mining and general engineering.
• Australian Standard: AS1418.2
Capacity Part No. Beam Range (mm)
Headroom (min / mm)
Headroom (max / mm)
Suspension pin dia (mm)
Weight (kg)
1 tonne 48246 65 - 230 78 135 20.3 4.8
2 tonne 48247 65 - 230 78 135 20.3 5.5
3 tonne 48248 100 - 250 100 160 22.1 11.8
5 tonne 48249 100 - 320 119 159 40.0 16.0
10 tonne 48276 130 - 320 150 205 53.0 31.0
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
131“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsPacific Girder Clamps
Pacific Girder Clamps are used to safely suspend loads of many descriptions from girders (I-beams). Manual, Electric and Air hoist installations are examples of their wide capability of usage.
Features
• All Pacific girder clamps are manufactured to comply with AS4991.
• Quick and easy to install and reposition makes them ideal for maintenance tasks.
• Jaws clamp over girder flanges.
• Also suitable for lifting I-beams.
• Can be used at up to 45 degree angle with a 50% reduction in capacity.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1322015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model PGC310 PGC320 PGC330 PGC350 PGC390
Stock Code PGC310 PGC320 PGC330 PGC350 PGC390
Rated Capacity (kg) 1000 2000 3000 5000 10,000
Beam width range (mm) 80 - 245 80 - 245 90 - 310 90 - 310 90 - 320
Net Weight (kg) 3.5 4.5 9.5 11.0 16.0
Model PGC310 PGC320 PGC330 PGC350 PGC390
A 270 270 365 365 365
B 375 375 520 520 520
C 66 74 103 111 120
D 4 6 8 10 12
E 210 210 258 258 280
F 165 165 225 225 230
G 25 25 45 45 50
H 50.5 - 82 50.5 - 82 80.5 -126 80.5 -126 94.5 - 138
I 12 12 19 19 21
Specifications
Dimensions (in mm)
1800 067 687
133“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsGirder Clamp
Auslift CG - 01 Ginder clamps are designed to lift steel girders and narrow steel plate or clamped on girder to utilize as a lifting point.
Features
• Capacities available from 1 tonne to 10 tonne.
• Can use on material hardness up to 37RC.
• Individually serial numbered comes with Test Certificate and user manual.
• Complies to AS4991 & AS1418.2.
Code WLL ADJ Beam Size
Wt. Dimensions
A B C D E F G H
T mm kg maxmm
minmm
maxmm mm mm mm
minmm
maxmm mm mm
132005 1 75 - 220 4.5 260 180 360 64 5 215 102 155 25 22
132010 2 75 - 220 5.2 260 180 360 74 6 215 102 155 25 22
132013 3 80 - 320 10 354 490 490 103 8 260 140 225 45 24
132015 5 80 - 320 11.1 354 490 490 110 10 260 140 225 45 28
132020 10 90 -320 20 365 505 505 120 12 280 170 235 50 40
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1342015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Top Girder Clamps
Pacific Top Girder Clamps are ideal for situations where quick and easy installation is required with no use of tools. They are suited to a wide range of beam sizes and the Low Profile Girder Clamp is the solution for applications where headroom is restricted. The locking pin with articulated handle will make this device easy to attach. Both the Standard and the Low Profile clamps are designed and tested in accordance with Australian Standard AS4991.
Features
• Designed and tested in accordance with Australian Standard AS4991.
• Quick and easy installation with no tools required.
• Suitable for a wide range of beam sizes.
• Available as a Low Profile Girder Clamp for applications where headroom is restricted.
• Inclusive of a locking pin with articulated handle for safe and easy fixture.
• A cost-effective and time saving way of suspending loads.
• This clamp can be used as both an anchor and suspension device.
• Ideal for the rigging industry.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
135“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsModel CLP257 CLP258
Rated Capacity 200 kg 200 kg
Head Room Standard Low Profile
Beam Size (mm) 90 - 204 90 - 180
Weight (kg) 5.8 4.5
Model CLP257 CLP258
A 357 (max) 407
B 90 - 204 259
C 150 90
D 60 90 - 180
E - 130
F - 60
Specifications
Dimensions (in mm)
1362015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Vertical Lifting ClampsVertical Plate Clamp - Model E
• Dependable latch type safety lock (spring type clamping mechanism).
• Automatic Powerful clamping mechanism, clamps securely in proportion to the weight of the load.
• Clamps with a force of more than twice the lifting load, yet leaves the material free from unnecessary scars.
• Induction hardened, special alloy steel cam.
• Main body made of high-tensile steel with a welded construction, resistant to cracks.
• Round swivel jaw to grip steel materials securely.
• Easy to handle, large sized lifting shackle.
• Baked epoxy finish.
• Crack resistant, welded construction.
• Lightweight, easy to use, safety lock latch.
• PWB VPC & SBBA state higher grade steel suitability.
• Manufactured in Japan.
• Applications: Lifting, moving and turning steel plates.
• Australian Standard: AS 4991
1800 067 687
137“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Clamps
Pa
rt N
o.
Mo
de
l
WLL
(to
nn
es)
Ha
ard
ne
ss
Ra
ng
e
Eff
ect
ive
T
hic
kn
ess
(m
m)
We
igh
t (k
g)
A (
mm
)
B (
mm
)
C (
mm
)
D (
mm
)
E (
mm
)
F (
mm
)
G (
mm
)
H (
mm
)
I (m
m)
R (
mm
)
W1
(mm
)
W2
(m
m)
43283 E-1t 1.0 Hv 85-320 3-20 3.6 23 36 124 50 24 225-265 33 155 12 38 51 30
43284 E-1t 1.0 Hv 85-320 3-30 4.3 34 34 141 50 25 240-295 35 180 12 38 51 30
43286 E-2t 2.0 Hv 85-320 3-30 5.7 35 35 153 60 30 270-320 40 194 14 44 60 36
43287 E-3t 3.0 Hv 85-320 3-35 9.0 40 50 175 60 35 315-375 45 226 19 50 68 40
43290 E-5t 5.0 Hv 85-320 5-45 16.7 50 50 218 65 45 380-440 57 260 22 55 76 44
1382015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Vertical Lifting ClampsAnchor Plate Lifting Clamp - Model VPC
• Rigid steel construction.• Manufactured in China.
• Applications: Lifting, moving and turning steel plates.
• Australian Standard: AS 4991
Pa
rt N
o.
Mo
de
l
WLL
(to
nn
es)
Ha
ard
ne
ss
Ra
ng
e
Eff
ect
ive
T
hic
kn
ess
(m
m)
We
igh
t (k
g)
A (
mm
)
B (
mm
)
C (
mm
)
D (
mm
)
E (
mm
)
F (
mm
)
G (
mm
)
H (
mm
)
I (m
m)
R (
mm
)
W1
(mm
)
W2
(m
m)
49311 1t VPC 1.0 Hv 85-400 3-20 3.9 25 37 125 50 24 275 30 156 14 38 53 31
49667 2t VPC 2.0 Hv 85-400 3-30 6.0 36 45 155 60 30 320 51 194 15 44 60 35
49668 3t VPC 3.0 Hv 85-400 3-35 9.8 40 47 175 60 36 380 58 227 20 51 68 39
1800 067 687
139“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsVertical Lifting ClampsVertical Non-marring Clamp - Model NE
• Screw type, wedge clamping mechanism with smooth rotation.
• Automatic powerful clamping mechanism, clamps securely in proportion to the weight of the load.
• Large-sized, high tensile steel wedge to securely grip steel plates without scars.
• Main body made of high-tensile steel with a welded construction, resistant to cracks.
• Easy to handle, large sized lifting shackle.
• Stopper cam locking mechanism to prevent slippage.
• Guide pin which allows visual indication of locking.
• Baked epoxy finish.
• Manufactured in Japan.
• Applications: Lifting, moving and turning steel plates.
• Australian Standard: AS 4991
1402015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Part No. Model WLL (tonnes)
HaardnessRange
Jaw Opening (mm)
Effective Thickness (mm)
Weight (kg)
45005 NE-0.5t 0.5 Hv 85 - 250 0 - 20 3 -20 5.8
45006 NE-1t 1.0 Hv 85 - 250 5 - 25 5 - 25 8.6
45007 NE-2t 2.0 Hv 85 - 250 5 - 30 5 - 30 15.1
45008 NE-3t 3.0 Hv 85 - 250 10 - 35 10 - 35 23.6
Mo
de
l
I (m
m)
I 1
(mm
)
I 2
(m
m)
L (m
m)
H1
(mm
)
H2
(m
m)
H3
(m
m)
H (
mm
)
W1
(mm
)
W2
(m
m)
W (
mm
)
D (
mm
)
R (
mm
)
T (
mm
)
A (
mm
)
B(m
m)
NE - 0.5t 25 55 68 148 18 78 99 195 36 48 60 50 40 12 40 40
NE - 1t 31 60 80 171 27 88 110 225 43 55 71 50 45 16 50 50
NE - 2t 36 71 91 198 26 107 133 266 54 71 87 60 55 19 50 60
NE - 3t 40 85 100 225 35 110 155 300 62 82 102 60 55 19 60 60
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
141“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsCrosbyip Lifting Clamps
The CrosbyIP range of lifting clamps are manufactured from high quality steel which has been forged, quenched, tempered and heat-treated to guarantee the safety and durability required by industrial applications. All clamps have been ergonomically designed to be user friendly (smaller, lighter and more compact), while not sacrificing strength and durability.
The CrosbyIP lifting clamps are available in a variety of models to allow the lifting and transferring of steel plates and other materials in a wide variety of industries. These industries include ship building, offshore, aircraft, construction and metal-processing.
Features
• All models are manufactured to comply with AS4991.
• Manufactured by a market world leader.
• All clamps have been subject to rigorous quality control for maximum reliability.
• All products are supplied with a test certificate and instruction manual.
• All vertical plate clamps may be used to lift materials with a hardness up to 345 Brinell (37Rc).
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1422015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Clamp Type Model Rated Capacity (kg)
Jaw (mm) Stock Code
Universal Vertical Plate
This model is based on the IP10 lifting clamp but is equipped with a universal (hinged) hoisting eye. This makes it possible to lift loads from any given direction. The IPU10 clamp is also very useful in applications where larger plate are to be lifted with two clamps in combination with a two-legged chain.
0.5 - IPU101 - IPU102 - IPU103 - IPU10
4.5 - IPU106 - IPU109 - IPU10
9 - IPU10/J12 - IPU10
12 - IPU10/J
50010002000300045006000900090001200012000
0 - 160 -200 - 350 - 400 - 400 - 500 - 50
50 - 1000 - 54
54 - 108
CLP005CLP010CLP020CLP030CLP040CLP060CLP070CLP071CLP080CLP081
Vertical Plate
The IP10 clamps may be used to lift, turn by 180o and vertically transport steel plates and construction elements.
0.5 - IP101 - IP102 - IP103 - IP10
4.5 - IP106 - IP109 - IP10
9 - IP10/J12 - IP10
12 - IP10/J
50010002000300045006000900090001200012000
0 - 160 -200 - 350 - 400 - 400 - 500 - 50
50 - 1000 - 54
54 - 108
CLP014CLP012CLP022CLP032CLP042CLP062CLP075CLP076CLP085CLP086
Non Marring Vertical Plate
1 - IPNM10 1000 0 - 20 CLP410
Specifications
1800 067 687
143“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsHorizontal Lifting ClampsHorizontal Plate Clamps - Model HO
• Lightweight, induction-hardened, special alloy cam with a lifting hole.
• No side-slipping construction.
• Automatic, powerful clamping mechanism, clamps securely in proportion to the weight of the load. Leaves the materials free from unnecessary scars.
• Main body made of high tensile steel with a welded construction, resistant to cracks.
• Simple construction and operation.
• Baked epoxy finish.
• Must be used in pairs for horizontal lifting.
• Spring closed action on 1 tonne WLL unit (pictured).
• Sprung open on 2tonne & 3 tonne WLL units.
• Manufactured in Japan.
• Applications: Horizontal lifting, moving of steel plate
• Australian Standard: AS 4991
Part No.
A (mm)
B (mm)
C (mm)
D (mm)
E (mm)
F (mm)
G (mm)
H (mm)
I (mm)
J(mm)
WLL per pair (tonnes)
Set(comprising)
EffectiveThickness
(mm)
Weight (kg)
44922 56 80 126 126 32 92 16 100 16 206 1.0 2xHO - 0.5T 10-50 8.0
44923 65 95 185 145 36 142 29 110 19 240 2.0 2xHO - 1.0T 10-50 15.0
44924 67 115 210 160 40 160 36 120 22 267 3.0 2xHO - 1.5T 10-50 22.0
1442015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Horizontal Lifting ClampsHorizontal Plate Clamps - Model HPC
• Must be used in pairs for horizontal lifting.
• Spring closed action on 1.5 tonne WLL unit.
• Sprung open on 3 tonne and 5 tonne units.
• Manufactured in China.
• Applications: Horizontal lifting, moving of steel plate
• Australian Standard: AS 4991
Part No.
WLL perpair
(tonnes)
A (mm)
B(mm)
C(mm)
D (mm)
E (mm)
F (mm)
G (mm)
H (mm)
I(mm)
J(mm)
Set(comprising)
EffectiveThickness
(mm)
Weight (kg)
49669 1.5 55 82 127 127 30 50 16 100 16 38 2x750kg HPC 10-50 8.0
49670 3.0 52 130 220 157 36 142 32 110 19 47 2x1.5t - HPC 10-50 15.0
49671 5.0 56 155 260 181 40 172 40 130 22 60h 2x2.5T - HPC 10-50 29.0
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
145“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Clamps
Clamp Type Model Rated Capacity (kg)
Jaw (mm) Stock Code
Horizontal Plate
These clamps are suitable for the lifting and transfer in horizontal position of non-sagging steel plates. The clamp is equipped with a handle for simple and easy placement onto the plate. These clamps must be used in pairs or more. Available in capacities of 2 to 12 tonne. All clamps are individually proof tested to 2 times the rated capacity with certification.
2 IPH10E3 IPH10E3 IPH10E
4.5 IPHTONZ6 IPH10E6 IPH10JE9 IPH10E9 IPH10JE12 IPH10E12 IPH10JE
200030003000450060006000900090001200012000
0 - 600 - 60
60 - 1200 - 600 - 60
60 - 1200 - 60
60 - 1200 - 60
60 - 120
CLP516CLP531CLP536CLP545CLP561CLP571CLP091CLP096
--
Horizontal Lifting Clamp (Manual pre-tensioning)
1 - IPBC2 - IPBC
10002000
0 - 200 - 25
CLP100CLP200
Horizontal Plate (with locking device)
1.5 - IPHGZ3 - IPHGZ
15003000
0 - 250 - 40
CLP115CLP130
Horizontal Pipe Hook (pair)
2 - IPP 2000 200 CLP320
Specifications
1462015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Horizontal Plate Clamp
Austlift HPC Horizontal Lifting Clamps are used in pairs to lift and transport steel material on a flat plane confiration.
• Capacities available from 0.75 tonne to 5 tonne per pair.
• Can be used on material hardness up to 37RC.
• Individually serial numbered comes with Test Certificate and user manual.
• Spare Parts are available.
• Complies to AS4991.
Code WLL Jaw Opening
Wt. Eye Height Width
T mm kg dia mm mm
143075 0.75 0 - 25 3.5 ø25 175 125
143100 1 0 - 30 4 ø30 205 161
143150 1.5 0 - 30 4.3 ø30 205 161
143200 2 0 - 35 7.2 ø30 245 175
143300 3 0 - 40 8 ø30 250 180
143500 5 0 - 50 9 ø30 260 185
1800 067 687
147“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsMulti- Directional Lifting ClampsScrew Clamp - Model SBB
• Patented ‘torque confirmation device’ (visible red ring indicates when tightening force is
achieved).
• For horizontal and vertical lifting applications.
• Spring type pressure locking device.
• Twin shackle allows for movement in any direction.
• Double safety feature with screw type vice and automatic clamping mechanism.
• Forged special alloy steel body with galvanised finish.
• Clamp screw and swivel jaw made of induction hardened, alloy steel.
• Tightening force must be minimum of 150kgf-cm.
• Attachment and detachment are easily performed with the patented spring collar.
• Manufactured in Japan.
• Applications: Lifting, moving of steel plate
• Australian Standard: AS 4991
1482015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Part No. Model WLL (tonnes)
Hardness Range
Effective Thickness
(mm)
Weight (kg)
44925 SBB - 05 0.5 Hv 85 - 320 1 - 25 1.8
44926 SBB - 1 1.0 Hv 85 - 320 1 - 40 4.0
44927 SBB - 2 2.0 Hv 85 - 320 1 - 40 7.6
43497 SBB - 3 3.0 Hv 85 - 320 5 - 35 8.3
43496 SBB - 5 5.0 Hv 85 - 320 10- 40 14.3
Mo
de
l
B (
mm
)
C (
mm
)
D (
mm
)
E (
mm
)
F (
mm
)
G (
mm
)
H (
mm
)
I (m
m)
J (m
m)
K (
mm
)
L (m
m)
M (
mm
)
N (
mm
)
O (
mm
)
P (
mm
)
Q (
mm
)
R (
mm
)
S (
mm
)
SBB-05 23 25 27 22 41 29 140 112 15 24 96 20 46 26 150 15 24 27
SBB-1 30 45 32 31 61 46 203 166 18 34 124 24 55 36 150 22 34 32
SBB-2 37 43 36 44 66 46 218 185 25 38 134 32 74 44 150 25 36 32
SBB-3 40 47 45 40 60 60 240 170 30 43 137 36 80 50 150 30 30 31
SBB-5 48 55 50 45 70 70 276 213 35 47 150 40 96 60 150 35 45 37
1800 067 687
149“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
ClampsMulti- Directional Lifting ClampsScrew Clamp - Model SBBA
• Patented ‘torque confirmation device’ (visible red ring indicates when tightening force is achieved).
• Suitable for most bisalloy steel (up to Hv600).
• Spring type pressure locking device.
• Twin Shackle allows movement in any direction.
• Double safety feature with screw type vice and automatic clamping mechanism.
• Clamp screw, edge pad and swivel jaw made of induction hardened, alloy steel.
• For steel plates with higher hardness range.
• Tightening force on SBBA must be a minimum of 300kgf-cm.
• Manufactured in Japan.
• Applications: Lifting, moving of steel plate
• Australian Standard: AS 4991
1502015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Part No. Model WLL (tonnes)
Hardness Range
Effective Thickness
(mm)
Weight (kg)
44932 SBBA- 05 0.5 Hv 85 - 600 1 - 25 1.8
49600 SBBA - 1 1.0 Hv 85 - 600 1 - 40 4.0
49601 SBBA - 2 2.0 Hv 85 - 600 1 - 40 7.6
49602 SBBA - 3 3.0 Hv 85 - 600 5 - 35 8.3
Mo
de
l
B (
mm
)
C (
mm
)
D (
mm
)
E (
mm
)
F (
mm
)
G (
mm
)
H (
mm
)
I (m
m)
J (m
m)
K (
mm
)
L (m
m)
M (
mm
)
N (
mm
)
O (
mm
)
P (
mm
)
Q (
mm
)
R (
mm
)
S (
mm
)
SBBA-05 23 25 27 22 41 29 140 223 15 24 96 20 46 26 150 15 24 27
SBBA-1 30 45 32 31 61 46 203 166 18 34 124 24 55 36 150 22 34 32
SBBA-2 37 43 36 43 66 45 210 183 25 38 134 32 70 44 150 25 36 32
SBBA-3 40 47 45 40 60 60 240 170 30 42 137 36 80 50 150 30 30 31
1800 067 687
151“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Clamps
Code WLL Jaw Opening Wt. Eye Height Width
T mm kg dia mm mm
142075 0.75 0 - 15 2 ø30 218 105
142150 1.5 0 - 20 7.4 ø60 370 170
142200 2 0 - 25 7.8 ø60 375 175
142300 3 0 - 30 16 ø60 418 195
142500 5 0 - 50 23 ø80 480 230
Universal Plate Clamps
Austlift UPC range of Clamps are equipped with a Universal Hinged Lifting Eye, making it possible to lift loads from any given direction.
Features
• Capacities available from 0.75 tonne to 5 tonne.
• Can be used on material hardness up to 37RC.
• Individually serial numbered comes with Test Certificate and user manual.
• Spare Parts are available.
• Complies to AS4991.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1522015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Magnetic Lifters can be used in various industries for the lifting and moving of steel, engine parts, semi-manufactured goods and moulds, Due to its magnetic force, there is no need to use slings, clamps or other holding devices. This will eliminate the chance of damaging the lifted materials.
Pacific Magnetic Lifters
Features
• The magnetic lifter features a breakaway force 3.5 times greater than the working load limit.
• Weight capacities are available from 100kg to 6000kg.
• No electricity needed which will increase product safety. Once operated there is less than 1% residual magnetism.
• The simple switch and safety button design allows for one handed operation.
• Use of plate with high-carbon content will reduce the absorbability to less than 50% of rated capacity. Use of plate with high carbon content is not recommended.
Model PML -1 PML -3 PML -6 PML -10 PML -20 PML -30 PML -60
Stock Code MAG010 MAG030 MAG060 MAG100 MAG200 MAG300 MAG600
Rated Capacity (kg) 100 300 600 1000 2000 3000 6000
Cylindrical Carrying Capacity (kg) 50 150 300 500 800 1200 1800
Max. Break-away Force (kg) 350 1050 2100 3500 7000 10500 21000
Net Weight (kg) 3 10 24 50 125 240 440
Specifications
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
153“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Magnetic LifterRate of Reduction Graph
Model PML -1 PML -3 PML -6 PML -10 PML -20 PML -30 PML -60
Rated Capacity (kg) 100 300 600 1000 2000 3000 6000
Suitable Thickness of Plate (mm) > 25 > 35 > 40 > 50 > 60 > 80 >120
Plate Material ≤ 45# steel ≤ 45# steel ≤ 45# steel ≤ 45# steel ≤ 45# steel ≤ 45# steel ≤ 45# steel
Carbon Content Low Low Low Low Low Low Low
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1542015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Dimensions (in mm)
Model PML -1 PML -3 PML -6 PML -10 PML -20 PML -30 PML -60
A 67 91 117 163 212 261 355
B 62 92 122 176 234 286 430
C 92 162 232 258 378 458 600
D 126 155 196 285 426 521 -
1800 067 687
155“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Magnetic LifterPermanent Magnetic LifterAustlift AM-1 Permanent Magnetic Lifter have a wide variety of uses for lifting and shifting steel products, flat plate and round bar, steel parts and finished steel goods etc. This versatile lifting device has the advantage of moving material without damaging the steel surface.
• Capacities available from 100kg to 6,000kg.
• No power source required with less than 1% residual magnetism.
• Simple to operate with safety button design.
• Magnet breakaway force of 3.5 times the Work Load Limit.
• Complies to AS4991 with test certificate supplied.
Product Code
Rated Lifting Strength (Kgf )
Vertical / Cylindrical Lifting Strength
(Kgf )
Max. Pull-off Strength (Kgf )
Dimensions (mm) Operation Temperature
(°C)
Net Weight (Kg)
L W H R
144101 100 30 300 92 64 70 145 <80 3
144102* 200 60 600 114 72 86 145 <80 5
144103 300 100 900 165 88 96 176 <80 10
144104* 400 130 1000 165 88 96 176 <80 10
144106 600 200 1800 216 118 118 219 <80 20
144110 1000 300 3000 264 148 138 266 <80 37
144150* 1500 500 3750 264 168 168 285 <80 50
144200 2000 600 5000 352 168 168 380 <80 70
144300* 3000 1000 7500 424 188 183 478 <80 100
144400* 4000 1300 10000 508 226 215 612 <80 160
144500* 5000 1500 12500 516 290 265 627 <80 290
144600* 6000 2000 15000 582 290 265 627 <80 320
* Non-stocked items, please check with us.
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1562015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Pacific Load Skates
The Pacific Load Skates are designed to facilitate the moving, positioning or installation of a wide range of loads, including heavy equipment, machinery and bridge structures. The optional turntable and positioning handle ensure that these load skates are suitable for many applications.
Features
• Available in capacities varying from 5 to 75 tonne.
• Optional turntable and positioning handle available for all models.
• High visibility colours for safety purposes.
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
157“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Load Skates
Model LSK005 LSK010 LSK020 LSK030 LSK050 LSK075
Stock Code LSK005 LSK010 LSK020 LSK030 LSK050 LSK075
Rated Capacity per 4 Units (tonne) 5 10 20 30 50 75
Rated Capacity per Units (tonne) 1.25 2.5 5 7.5 12.5 18.75
Unit Length (mm) 169 188 210 210 275 290
Unit Width (mm) 100 100 100 100 140 145
Unit Height (mm) 65 65 65 65 100 100
Unit Track Width (mm) 55 55 55 55 72 72
Unit Roller Diameter (mm) 20 20 20 20 30 30
Number of Rollers per unit 12 14 16 16 14 14
Rollers in Contact 4 5 6 6 6 6
Net Weight (kg) 3.9 4.5 5.0 5.0 18.0 18.0
Stock Code Turntable LSK120 LSK120 LSK120 LSK120 LSK175 LSK175
Height incl. Turntable (mm) 100 100 100 100 - 145
Turntable Top Diameter (mm) 100 100 100 100 - 150
Specifications
1582015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Endo Spring BalancersERP Series Spring Balancers
» Standard features include:
• Strong, lightweight aluminium body.
• Easy maintenance with interchangeable kit parts.
• Tapered drum for exact torque retraction across the full stroke.
• Food Grade Balancers also available.
• Suitable industries: Engineering, manufacturing and abattoirs• Applications: Suspension of electric or pneumatic power tools, or
for hanging tools, parts or welding equipment atworkstations or
assembly lines.
Capacity Min (Kg) Capacity Max (Kg) Part No. Model Stroke (m) Weight (kg)
0.3 0.6 43997 ERP - 06 1.5 0.4
Capacity Min (Kg)
Capacity Max (Kg)
Part No. Model Stroke (m)
Weight (kg)
0.5 1.5 43335 EK - 00 0.5 0.2
0.5 1.5 43334 EK - 0 1.0 0.5
EK Series Spring Balancers
» Standard features include:
• Strong, lightweight aluminium body.
• Easy maintenance with interchangeable kit parts.
• Tapered drum for exact torque retraction across the full stroke.
• Food Grade Balancers also available.
• Suitable industries: Engineering, manufacturing and abbattoirs
• Applications: Suspension of electric or pneumatic power tools, or for hanging tools,
parts or welding equipment at workstations or assembly lines.
1800 067 687
159“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Spring BalanceEndo Spring BalancersEW Series Spring Balancers
» Standard features include:
• Strong, lightweight aluminium body.
• Heavy duty top and bottom hook.
• Easy maintenance with interchangeable kit parts.
• Tapered drum for exact torque retraction across the full stroke.
• Food Grade Balancers also available.
• Suitable industries: Engineering, manufacturing and abattoirs
• Applications: Suspension of electric or pneumatic power tools, or for hanging tools, parts or welding
equipment at workstations or assembly lines
Capacity Min (Kg)
Capacity Max (Kg)
Part No. Model Stroke (m)
Weight (kg)
1.0 3.0 47885 EW - 3 1.3 1.4
2.5 5.0 47886 EW - 5 1.3 1.5
EWF Series Spring Balancers
» Standard features include:
• Strong, lightweight aluminium body.
• Heavy duty top and bottom hook.
• Easy maintenance with interchangeable kit parts.
• Tapered drum for exact torque retraction across the full stroke.
• “Anti Snap Back” models available.
• Food Grade Balancers also available.
1602015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
• Suitable industries: Engineering, manufacturing and abattoirs
• Applications: Suspension of electric or pneumatic power tools, or for hanging tools,
parts or welding equipment at workstations or assembly lines
Capacity Min (Kg)
Capacity Max (Kg)
Part No. Model Stroke (m)
Weight (kg)
4.9 9.0 44263 EWF9 1.3 3.5
9 15 44264 EWF15 1.3 3.8
15 22 44265 EWF22 1.5 7
22 30 44266 EWF30 1.5 7.6
30 40 44267 EWF40 1.5 9.8
40 50 44268 EWF50 1.5 10.2
50 60 44269 EWF60 1.5 11.6
60 70 44270 EWF70 1.5 11.9
ELF Series Spring Balancer
» Standard features include:
• Strong lightweight aluminium body.
• 2.5 metre cable lengths.
• Heavy duty top and bottom hook.
• Easy maintenance with interchangeable kit parts.
• Tapered drum for exact torque retraction across the full stroke.
• Suitable industries: Engineering, manufacturing and abattoirs
• Applications: Ideal for applications for balancers that require a
longer stroke
1800 067 687
161“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Spring BalanceCapacity Min (Kg) Capacity Max (Kg) Part No. Model Stroke (m) Weight (kg)
1.5 3.0 45508 ELF - 3 2.5 4.1
3.0 5.0 45509 ELF - 5 2.5 4.2
5.0 9.0 45510 ELF - 9 2.5 4.7
9.0 15.0 45794 ELF - 15 2.5 10.0
15.0 22.0 45795 ELF - 22 2.5 10.2
22.0 30.0 45796 ELF - 30 2.5 11.0
30.0 40.0 45797 ELF - 40 2.5 14.0
40.0 50.0 45798 ELF - 50 2.5 14.5
50.0 60.0 45799 ELF - 60 2.5 17.0
60.0 70.0 45800 ELF - 70 2.5 18.1
Capacity Min (Kg) Capacity Max (Kg) Part No. Model Hose Travel (m) Weight (kg)
0.5 1.5 43351 ATB - 0 1.3 1.6
1.5 3.0 43352 ATB - 1 1.3 1.7
Air Tool BalancersAir Tool balancers perform the function of both hose reel and balancer.
» Standard features include:
• Strong lightweight aluminium body.
• Heavy duty top and bottom hook.
• Easy maintenance with interchangeable kit parts.
• Tapered drum for exact torque retraction across the full stroke.
• Suitable industries: Engineering, manufacturing and abattoirs
• Applications: Suspension of air tools
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1622015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Kromer Spring Balancers
Kromer Spring Balancers (Retractors) and Zero Gravity Balancers are designed to support heavy handoperatedprocess tools and enables them to be operated with minimum effort. The balancers will automatically retract the tool to its initial position upon releasing it after use. An automatic arresting mechanism (ratchet lock) is available in some models. It allows setting retraction stops to keep the load suspended at predefined positions. The stops are automatically activated if the working load (tool) is moved back slowly. If pushed back fast, the mechanism remains inactive.
Features
• Stops automatically if main spring fails.
• Safety expansion chain as a separate added fall prevention device.
• Step less load balancing via worm gearing.
• Replaceable high grade steel main spring.
• Cable limiters prevent overload damage.
• Cable exit opening prevents wear.
• Adjustable return stop and buffer.
• High strength safety hook can be swivelled and adjusted laterally for easy loading.
• Minimises operator fatigue and encourages smooth work processes.
• Models 7212 / 7222 / 7231 / 7236 are fitted with ratchet lock as standard.
• Models 7241 and 7251 can be supplied with optional ratchet lock.
• Shock resistant and non-abrasive housing.
• All spring balancers have been life-tested and meet the terms of the DIN 15112 requirements. They also comply with the relevant EC legislation as attested by the CE-mark. In addition, they hold the “GS” mark (safetytested).
1800 067 687
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
163“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Spring Balance
Model Stock Code Capacity (kg) Stroke (m) Weight (kg)
7200 - 1 KRM001 0.5 - 1.5 1.6 0.5
7211 - 1 KRM111 0.5 - 2.0 2.5 0.8
7211 - 2 KRM112 1.5 - 3.0 2.5 0.8
7212 - 1 KRM121 0.5 - 2.0 2.5 0.9
7212 - 2 KRM122 1.5 - 3.0 2.5 0.9
7221 - 1 KRM211 2.0 - 5.0 3.0 3.3
7221 - 2 KRM212 4.0 - 8.0 3.0 3.7
7221 - 3 KRM213 7.0 - 10.0 3.0 3.7
7221 - 4 KRM214 10.0 - 14.0 3.0 3.9
7222 - 1 KRM221 2.0 - 5.0 3.0 3.5
7222 - 2 KRM222 4.0 - 8.0 3.0 3.8
7222 - 3 KRM223 7.0 - 10.0 3.0 3.8
7222 - 4 KRM224 10.0 -14.0 3.0 4.0
7230 - 4 KRM304 9.0 - 14.0 2.0 3.4
7230 - 5 KRM305 13.0 - 17.0 2.0 3.6
7230 - 6 KRM306 16.0 - 21.0 2.0 3.8
7231 - 4 KRM314 9.0 - 14.0 2.0 3.6
7231 - 5 KRM315 13.0 - 17.0 2.0 3.8
7231 - 6 KRM316 16.0 - 21.0 2.0 4.0
7235 - 1 KRM351 15.0 - 25.0 2.0 7.8
7235 - 2 KRM352 25.0 - 35.0 2.0 8.9
7235 - 3 KRM353 35.0 - 45.0 2.0 9.5
7235 - 4 KRM354 45.0 - 55.0 2.0 9.75
Specifications
The information shown is to be used as a guide only. Specifications are subject to change without notice.
All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
1642015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Model Stock Code Capacity (kg) Stroke (m) Weight (kg)
7236 - 1 KRM361 15.0 - 25.0 2.0 8.9
7236 - 2 KRM362 25.0 - 35.0 2.0 10.0
7236 - 3 KRM363 35.0 - 45.0 2.0 10.6
7236 - 4 KRM1364 45.0 - 55.0 2.0 10.85
7241 - 2 KRM412 20.0 - 30.0 2.0 15.2
7241 - 3 KRM413 30.0 - 45.0 2.0 16.9
7241 - 4 KRM414 45.0 - 60.0 2.0 17.3
7241 - 5 KRM415 60.0 - 75.0 2.0 18.7
7241 - 6 KRM416 75.0 - 90.0 2.0 19.7
7251 - 1 KRM521 15.0 - 25.0 3.0 25.0
7251 - 2 KRM522 25.0 - 35.0 3.0 26.0
7251 - 3 KRM523 35.0 - 50.0 3.0 27.0
7251 - 4 KRM524 50.0 - 65.0 3.0 28.0
7251 - 5 KRM525 65.0 - 80.0 3.0 29.0
7251 - 6 KRM526 80.0 - 90.0 3.0 30.0
7251 - 7 KRM527 90.0 - 100.0 3.0 32.0
7251 - 10 KRM530 130.0 -140.0 3.0 44.6
7261 - 3 KRM613 200.0 - 225.0 1.5 49.0
Specifications
1800 067 687
165“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
Clamps
Part No. Model Capacity (kg) Drum Size Headroom (mm)
Suspension hole Dia (mm)
Weight (kg)
44274 Vertical Drum Clamp 500 200 152 50 5
Drum ClampsDrum Clamps
Three designs are available to provide safe, fast lifting and repositioning of 210 litre (44 gallon) drums, with or without lids. The available types are:
• Vertical drum clamp (suitable for drums with a lid).
• Horizontal drum clamp (suitable for drums with a lid).
• Vertical drum tong (for drums without a lid).
» Standard features include:
• Main body made of high tensile steel with welded construction that is resistant to cracks.
• Design factor 5:1.
• Epoxy painted finish.
• Applications: Lifting.
• Australian Standard: AS 4991
Drum
1662015 EDITION
CampbellfieldTel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Part No. Model Capacity (kg) Drum Size Headroom (mm)
Suspension hole Dia (mm)
Weight (kg)
44275 Horizontal Drum Clamp
500 200 470 50 5
Part No. Model Capacity (kg) Drum Size Headroom (mm)
Suspension hole Dia (mm)
Weight (kg)
44276 Vertical Drum tong 500 200 520 50 14
1800 067 687
167“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
TrolleySpecifications
Clamp Type Model Rated Capacity (kg)
Jaw (mm) Stock Code
Vertical Drum
The IPVK drum clamp is for vertical lift an transfer. Automatically locks on drum and can be used alone or in pairs. The IPDV drum is for vertical lift and transfer. Allows drum to remain in an upright position during the lift and transfer using one clamp.
0.5 - IPVK0.5 - IPDV
500500
17300
CLP900CLP910
Beam Clamp (with locking device)
1.5 - IPBHZ13 - IPBHZ
15003000
0 - 250 - 40
CLP580CLP585
Drum
1682015 EDITION Campbellfield
Tel (03) 9357 9611
Fax (03) 9357 9488
DandenongTel (03) 9794 5570
Fax (03) 9791 3212
KilsythTel: (03) 9761 4125
Fax: (03) 9761 4286
LavertonTel (03) 9314 4599
Fax (03) 9314 8766
Drum Trolley
Austlift Drum Trolley are specially designed to carry 210 litre (55 gallon) drums. Easy to use for fast repositioning of drums.
Features
• Work load limit 500 kg.
• Manufactured from hi-tensile steel.
Code WLL Wt. Dimensions
KG Kg A B C
mm mm mm
144005 500 5 600 170 50
1800 067 687
169“We have the right product, at the right price, when you need it, on-time, every time”[email protected]
www.keblestrading.com.au
DrumDrum Lifter
Austlift Drum Lifters are specially designed to lift 210 litre (55 gallon) drums vertically with or without lids. Easy
to use for fast lifting and repositioning of drums.
• Work load limit 600kg.
• Manufactured from hi-tensile steel with a safety factor of 5 to 1.
• Conforms to AS 4991, Test Certificates available.
Code Opening WLL Wt. Dimensions
H h M S W
mm tonne kg mm mm mm mm mm
144000 0 - 30 0.6 6.5 350 420 570 105 260
144001* 0 - 30 0.6 7.8 350 420 570 105 260
* Assembled with G80-10mm Master Link and 8mm Chain Connector for forklift.