Mastercam 2019 ReadMe - Support Services | CAD CAM...BETA101/25/2018 Category Name Number...

MASTERCAM 2019 README

May 2018

MASTERCAM 2019 README

May 2018© 2018 CNC Software, Inc. – All rights reserved.Software: Mastercam 2019

Terms of Use

Use of this document is subject to the Mastercam End User License Agreement. The Mastercam End User License Agreementcan be found at:

http://www.mastercam.com/companyinfo/legal/LicenseAgreement.aspx

Be sure you have the latest information!

Informationmight have changed or been added since this document was published. The latest version of the document isinstalled with Mastercam or can be obtained from your local Reseller. A ReadMe file (ReadMe.PDF) – installed with each release– includes the latest information about Mastercam features and enhancements.

2

http://www.mastercam.com/companyinfo/legal/LicenseAgreement.aspx

INTRODUCTION

Please review this ReadMe for last-minute product information about Mastercam 2019. Report any problems [email protected].

Mastercam 2019 ReadMe—Introduction

2

mailto:[email protected]

3

MASTERCAM 2019

Category Name Number

GeneralUpdated to Spatial R2018 SP2 in support of the .SAT and other ACIS-based import-ers/exportors; most notably increased Catia V5 import support to V5R28.

R-16266

GeneralJapanese characters did not output to text files in the IGES importer's Scan FIlefunction.

R-16047

Geometry Creation of a relief groove resulted in a crash. R-16249

InterfaceAnalyze Entity dialog box was missing the Propagate button, and the ability toright-click for Selcue values did not work.

R-16359

Interface Analyze Distance on a DZ plane resulted in reversed values. R-16142

Toolpaths ThreadMill's Entry/exit arc angle value on the LeadIn/Out page defaulted to 0. R-16314

Mastercam 2019 ReadMe—Mastercam 2019

BETA 5 04/12/2018


General Unicode issues were preventing text files from being output correctly. R-16047

Geometry Spline Blended did not give the expected result. D-34226

Geometry Surfaces created from a solid after a Dynamic Transformation were in the wronglocation.

R-16120

Geometry Spline Blend required additional work to create expected result. R-16095

Geometry Curves sometimes appeared to be incorrectly on or in front of surfaces. R-16059

Geometry Solids with new Plane associativity crashed. R-16001

Interface Updated to Granite 11 SDK in support of the import of ProE/Creo ® parts. Thisprovides support for the new release of Creo 5.0.

R-16028

Lathe STL stock did not display properly. R-15962

Tooling Manufacturer code did not output in the posted code. R-16115

Tooling When renumbering a tool, the tool number did not update in the operation, or rever-ted. This caused a crash.

R-11422

Mastercam 2019 ReadMe—BETA 5 04/12/2018

4

5

BETA 4 03/22/2018


General Opening STEP file caused crash in Mastercam 2018 andMastercam 2019. R-15848

General Importing a file fromMastercam for SOLIDWORKS into Mastercam 2019, geometryimported but the toolpath did not.

R-15887

Interface Scroll wheel inside of Translate panel in fields was not working. R-15775

Mill When deselecting geometry in Surface finish toolpath, Mastercam locked up. R-15831

Mill-Turn The Model Chamfer toolpath was returning grayed out lead in/out fields when usingPlane Rotation.

R-15596

General Licensed products were not properly shown as installed inMastercam Launcher. R-15906

Mill OptiRough and Area Roughing regression failed to regenerate. S-55130


BETA 3 03/01/2018


Configuration Selected edge line style was not being used in solids. R-15570

General Error reading files which contained solids with Japanese names. R-15619

General Attribute definition and block reference were missing, and improper type font wasimported on a drawing file.

R-15542

Geometry Solid edges were difficult to select in some situations. R-15645

Geometry Wireframe geometry residing along a surface edge was sometimes difficult to see. R-15451

Interface Replacing default value in the panel returned bad results when using right-click copyand paste.

R-15678

Interface Planes, Rotate Incremental reset the planes' Section state and color. R-15599

Interface Toggeling Levels All on/All off did not work properly. R-15571

Interface Viewsheets were removed after renaming local machine definition. R-15505

Interface Toolpaths could not be seen though glass entities. R-15452


6

7

BETA 2 02/08/2018


General Importing some STEP files failed if the step file was saved indifferent units than the current Mastercam session.

R-15244

Interface Levels were not maintained when exported as STEP. R-15347


BETA 1 01/25/2018


Backplot/Verify/Simulation

Mastercam Simulator with Rewind feature active caused crash when closingMastercam.

D-33179


Verify - Arc start radius did not equal arc end radius. D-33174


Verifyingmultiple transform operations inMastercam Simulator caused crash. D-33149


Verify Compare results were different first time than subsequent times. D-31676


Tool movement and display with Verify running was slow and choppy if the mousewas moving in the simulation area. If mouse was still, Verify ran normally.

D-26098


IOF error appeared first time launching IOF Simulation. D-24950


IOF Simulation was showing an extra move before cutting the contour. D-16919


Tool holder caused error in Verify. R-14795


Machine Simulation did not display fixture from a level. R-11311

Configuration Custom tabs did not display after importing the workspace file fromMastercam2018.

D-33358D-33220

Configuration AutoCursor Settings - Set the Quadrant setting to be off by default. R-15169

Configuration AddingMachine Type group to additional ribbon tabs disabledmachine selection. R-14742

Configuration Import function inOptions, Context menu was resulting in blank context menuwhenMastercam was localized.

R-08808

General When importing AutoCAD files, drawings were missing text upon conversion. R-15255

General Zero length line in imported DWG file caused axes lines not to display. R-15017

General Attached parasolid opened in Mastercam 2017 in a few seconds, in 2018 it took 20minutes.

R-14925

General Mastercam was unable to remember paper size selection for print in Japanese. R-14823

General Opening a DWF file in Mastercam 2017 and 2018 created random geometry,instead of what was actually in the file.

R-11909

Geometry Surface - Three Fillet Blend crashed when using the attached file. R-15153

Geometry Hitting [Enter] in Create Letters added extra lines to the text rather than closingthe function.

R-15108

Geometry Transform Stretch – Could no longer unselect an entity. R-14917

Geometry Curve Slice - Curve was not being created on all surfaces as expected. R-11788

Mastercam 2019 ReadMe— BETA 1 01/25/2018

8

9


Geometry Parting Line did not create curves on all edges. R-07765

Interface Editing operation defaults sometimes changed active color. D-33262

Interface Selecting a quick mask item was not always changing focus to the graphics area. R-15023

Interface Right-click copy no longer functioned in Mastercam 2018 and 2019. R-14972

Interface Level Manager – Purge Empty Levels did not always work correctly. R-14956

Interface Dynamic Plane - AutoCursormenuwas not enabled during initial gnomon place-ment.

R-14529

Interface Right-click paste overwrote entire field instead of inserting clipboard value. R-13996

Lathe Aggregate Head was not visible in Machine DefinitionManager. R-15259

Lathe C-axis Contour chain geometry was showing geometry as still chained after beingunselected.

R-15223

Lathe Lathe Miscellaneous Operations, Do not process this operation, was not func-tioning.

R-15096

Lathe Lathe Chuck Jaws OD #2 Reference point was not being used in the Pick Off/CutOff pickoff Z coordinate.

R-14955

Lathe Lathe C-axis toolpath - changing work offset did not mark the operation dirty. R-14845

Lathe Stock Models using C-Axis source operations were not positioned correctly. R-13974

Lathe Variables were not being passed to the post processor correctly. R-13626

Lathe Contour Rough ignored stock. R-13528

Lathe Stock was gone after Lathe Canned Finish operation. R-11578

Lathe Lathe Contour Rough gave No cuts were made error with 0.0 stock to leave. R-10764

Lathe Lathe Rough cuts were twice as deep as set in toolpathparameters.

R-08905

Lathe Toolplanes were not being calculated properly. R-07842

Lathe Lathe Roughmissed passes if cut angle was set to less than 1.3 degrees. R-07413

Mill 2D Dynamic Contour - No depth cuts with open chain. D-15965

Mill 2D Contour - Depth cuts were applied only to some chains. D-15935

Mill Dynamic OptiRest gouged part in rapid move. D-15450

Mill Dynamic OptiRest gouging on one of the feedmoves going through one of the fil-lets.

D-13422

Mill 2D Dynamic Area Mill did not clear top of island. D-09699

Mill 2D Dynamic Peel Mill finish passes had bad retracts. R-15219

Mill 2D Pocket toolpath used pocket type Open and open pocket cuttingmethod; nocorner radius was produced.

R-15207

Mill Finish pass depths were not working in C-Axis Face Contour. R-14073

Mill Surfacing Rough and Finish Toolpaths selection of solids was not working prop-erly.

R-13920

Mill Surface High Speed Toolpaths Project stock to leave not applied. R-13610



Mill When RCTF was enabled inDynamic Mill, Feed Rate changed if Preview toolpathwas accessed from the Cut Parameters page.

R-11916

Mill 2D Contour using Ramp, Multi pass and External corner break radius were fail-ing on last pass.

R-10011

Mill Stockmodel failed to build when usingmultiple drilling operations. R-07522

Mill Surface Finish Contour locked up - smoothing/tolerance related regression issue. R-05478

Mill 2D Dynamic Mill Rest Material crashedMastercam X8 when trying to generate atoolpath. If Containment Regions were added, it would then work.

R-05095

Mill Dynamic Mill spindle speed went back to the ramp in speed when using any of theMotion > Gap size, retract options.

R-04866

Mill 2D Dynamic Mill, Rest - ignored previous operation andmachining entire area. R-04631

Mill Helix Bore ignored Clearance value. R-04383

Mill If negative stock to leave equaled the tool radius, a Reporting Computation Errorwarning was displayed.

R-04003

Mill 3D Waterline with negative stock to leave needed warning. R-02848

Mill Surface Finish Contour - long regeneration eventually failed. D-13666

Mill Waterline plunge rate was not output in some cases. R-02595

Mill-Turn Output of Semi-finish speed resulted with improper turning spindle direction. R-15065

Mill-Turn Job setup pickoff position was not accepted when value was manually entered. R-14775

Mill-Turn Pinch turn operation and its associated operation did not have consistent syncpoints.

R-14410

Mill-Turn Thread Mill operation went dirty after it was opened with no changes made. R-10844

Mill Cutter compensation set to Control - compensation was only displaying in graph-ics window on last chain .

R-06273

Mill In 2D Dynamic Mill, Island Facing was not cutting the entire face. R-03844

Tooling Coolant was not set to tool's setting. R-14791

Tooling Renumbered tool was not listed in Tool Manager library. R-14570

Tooling Holders with four significant digits caused issues. R-13622

Toolpaths Hidden Stock Models were sometimes visible when file was opened. R-12965

Toolpaths Drill 5 axis - Added parameter to end of toolpath lines to denote this was a sub-type of drill.

S-52913

Wire Contour -Make tab cutoff move with skim cut checkbox was enabled whenchanging Tech sequence.

R-13500


10

11

TECHNICAL PREVIEW 12/28/2017


Configuration Startupmachine was loading alongside machine contained in the part file. R-14708

General Merging in STEP files incremented level numbers by 2 instead of 1. R-14899

General Drawing level names with "" or / caused the file to fail to export geometry. R-14806

Geometry [OK/New] did not clear prior selection in Surfaces from Solids. .R-14709

Geometry Vertical geometry was no longer deleted when projected using Transform Project. R-14797

Interface The graphics area controlled the [Delete] key, when the Levels properties area washidden, if trying to delete the level name.

R-14574

Interface [Alt] key remained active when [Alt+Tab] was used to switch to Mastercam. R-14329

Lathe Extending a chain resulted in air cutting in Lathe Canned toolpaths. R-14732

Lathe Lathe Canned Finish would not accept tool used in Lathe Canned Rough. R-14664

Lathe Clearance values for Plunge Turn toolpath created a collision with stock. R-14644

Lathe Legacy operation would not drag and drop in Toolpaths Manager. R-14596

Lathe Lathe Rough did not update stock correctly whenMinimum Arc length was toosmall.

R-11432

Mill 2D Contour using Ramp and Plunge setting gave an assert. R-14610

Mill High Speed ToolpathModel Geometry grid did not use the stock default when theSystem Configuration, Toolpath/Surface Selection, Drive Option was set to All.

R-14378

Mill 2D Contour, Depth cut orderwas disabled and effected the selection behavior. R-13943

Mill Trim toolpath caused a crash. R-13736

Mill Stock model appeared when unblanking entities. R-10185

Mill Contour tool paths with Tab Cutoff in separate operations duplicated the TabCutoff Operations when regenerated.

R-06309

Mill-Turn Mill Turn posting reverted lathe stock boundary to initial position. R-14661

Mill-Turn Code Expert crashed when posting. R-11294

Tooling Copied and editedHigh Feed tool disappeared from the library. R-14857

Tooling Migrating TOOLDBs changed the projection length for tools withmulti-segmentholders.

R-14485

Tooling Metric tools had non-displayable descriptions. R-11048

Tooling Added cut and plunge direction arrows to the graphics view for 3D tools S-52216

Toolpaths Manager Multi-threaded operations with dependents failed to regenerate D-33072

Toolpaths Manager Display Options, Dependencies were not applied to upstream operations. D-32550

Toolpaths Manager Exporting operations that use a solid displayed a warning, then caused crash. R-14663

Toolpaths Manager Contour multipasses could not post or Backplot after regeneration R-14518

ToolpathManager Toolpaths Manager lost focus after pasting operations using [CTRL+V]. R-13538

Wire Regenerating Agie Collar toolpath changed coordinates. R-14743

Mastercam 2019 ReadMe— Technical Preview 12/28/2017



General File, Merge creates entities on active level - used to create on unique level. D-32698

General Mastercam Home Learning Edition crashed when opening file. R-14591

General File, Mergeoverwrote existing level names. R-14558

General Nesting Toolpath filtered duplicate diameter tools. R-14503

General Printing error: Attempted an unsupported operation. R-14429

General FlattenSurf C-Hook was missing the text on the Flip U/V button. R-14385

General Convert Apply to all existing printers to a button . R-14332

Geometry Bounding Boxsize changed if circle was rotated. R-14592

Geometry The speed of creating a Curve Slice on the solid body had slowed down. R-14550

Geometry Trim Surface to Curves gave different results, based on chain start point. R-14501

Geometry Curve All Edges failed on X_T file. R-14486

Geometry Transform Project crashed when projecting arcs to solid face R-14412

Geometry Surface Trim to Curve on a torus or line did not do a clean job. R-14373

Geometry Solid Variable Radius Fillet, Cycle did not highlight the current point. R-14284

Geometry Arrows did not adjust for Hole Axis when changing orientation. R-13737

Geometry Parting Linemissed some edges. R-07765

Interface When changing entity color, the entity stayed selected if the selected color was thesame as the entity.

R-14441

Interface Fit included dirty toolpaths. R-14405

Interface Spin control settings did not work with the new panels. R-07900

Lathe Lathe Stock Advance operation did not work correctly when using Lathe Refer-ence points.

R-11299

Lathe Deselecting Inspection Length in Lathe Rough Tool, still used the values fromLead In/Out and Start/End of pass allowance.

R-07576

Mill-Turn Mill-Turn job setup type effected ID clamping diameter. R-13604

Mill 2D Area Mill missing depth cuts. D-29278

Mill Stock Model would not regenerate. R-13317

Mill Canned Text, Add functionality stoped functioning after a fixed number of inter-actions.

R-11118

Mill Stock Model used all available systemmemory, and did not process. R-07934

Toolpaths Curve 5-axis was offset from chain. R-14092

Toolpaths CustomWork Coordinate System in a Mastercam X9 file regenerated incorrectly. R-13487

Mastercam 2019 ReadMe—Technical Preview 11/30/2017

12

13



ATP Invoice data did not output to ATP reports. R-14314

General Opening a SOLIDWORKS file with the Import Solids History option selected, impor-ted a problematic solid that causedMastercam to crash.

D-20075

General Opening a SOLIDWORKS file with the Import Solids History option selected, impor-ted only one side of a flat instead of a flat on both sides.

D-14078

General Opening a SOLIDWORKS file with the Import Solids History option selected, impor-ted a part with a circular pattern that was incorrect.

R-14270

General Opening a file with corrupt machine file name causedMastercam to crash. R-14043

General Opening a SOLIDWORKS file with the Import Solids History option selected,caused incorrect results.

R-10819

Geometry The wrong section was trimmed when using Blended Spline. R-14199

Geometry When the Orientation was changed inHole Axis, the arrows did not adjust cor-rectly.

R-13737

Geometry Curve Slice did not create curves on all surfaces as expected. R-11788

Lathe Lathe Rough did not cut the entire chain when the insert corner radius was set to1/64.

R-14312

Lathe The spindle was reversed when using a C-axis Face Contour toolpath. R-13706

Mill 3D Finish Contour had an error when usingUndercutwith a tapered shank tool. R-14313

Mill Dynamic OptiRough's vertical retracts should have been rapid instead of feedrate.

R-14220

Mill-Turn The Select button was incorrectly labeled on the Part Geometry page for Mill-Turntoolpaths.

R-14001

Toolpaths Adjusting the end chain point during Guided Chaining did not move the directionarrows.

R-14424

Toolpaths Bad preparatory data was written to ASCII NCI when aMultiaxis Curve toolpathwas trimmed to stock.

R-14066

Toolpaths Multiaxis Curve, using 4 axis with tilt from Lines, did not respect the customWCS. R-13975

Toolpaths Multiaxis Roughing, Stock to leave was not correctly calculated in Mastercam2018.

R-13838

Toolpaths Blade Area Roughing, which was removed from theMultiaxis Parallel toolpath,has been returned to theMisc page.

R-13392

Toolpaths Added an option in Advanced Configuration, to turn off multiaxis toolpath thread-ing.

S-52058

Toolpaths Added a parameter to the NCI forMultiaxis Drill toolpath with a Safety Zone, todenote this is a sub-type of drill.

S-51556

Toolpaths Manager Draggingmultiple operations did not show the multiple folder icon. R-13537

Toolpaths Manager Added operationDependencies report output. S-51999




General [Enter] no longer functioned as OK and Create New Operation in Transformfunctions.

R-14184

General When nesting, an imported .ini file that referenced two Mastercam files onlybrought the operations from the first file into the Parts List.

R-14037

General Solids Chamfer had a tessellation issue. R-13707

General The Leader size prevented the dimension from being placed inside when using Cir-cular dimensions.

R-13593

General When using Transform,Offset Chains on a small part, the geometry disappearedor was not created.

R-13474

General Three Surface Blend used the untrimmed portion of the surface. R-13027

Interface System planes were changed after editing a lathe machine definition. D-31017

Interface Most Recently Used (MRU) list did not collapse when the [Enter] key was pressed. R-14069

Interface PlanesWork offset changed fromManual to Automatic when changing planes inlegacy toolpaths.

R-14034

Mill Avoidance was not applied when entire solid was selected. R-13147

Mill 3D Toolpaths Rough and Finish Stock did not use the defaults forWall Stock andFloor Stock, nor were the values output in NCI.

R-11818

Mill 3D High Speed Toolpaths, Model Geometry did not have the ability to save stockto leave values to defaults.

R-11690

Mill 3D Dynamic OptiRough gouged solid faces. R-10863

Reports Added geometry was not output in operation view. R-14010


14

15



Drafting The arrow size of anOrdinate dimension changed when placingmultiple dimen-sions.

R-13533

General A DWG file came in with bad data. R-14018

General Migration Wizard did not update binary post with the files. R-13802

General Dynamic Transform in 2D mode did not project the anchor point correctly. R-13774

General Classic Backplot had a graphics issue with tool showing through the part surface. R-13712

Lathe Cross Drill, Change at point output the absolute value instead of the incrementalvalue.

R-13738

Lathe Bad NCI was written for Lathe Canned Grooving. R-13692

Lathe Linearization tolerance was missing from the Lathe Finish dialog box. R-13588

Lathe Lathe created planes for all chains in a toolpath when changed to a Y-axis rotation. R-09342

Lathe Lathe Dynamic Rough started the toolpath with tool buried in the part and pro-duced an error.

R-08633

Lathe Lathe Pattern Repeat gouged a specific part. R-07588

Mill 3D High Speed Toolpaths - Project did not keepMachining Geometry and Stockvalues.

R-13848

Mill 3D Dynamic OptiRough gouged solid faces. R-10863

Mill 3D Dynamic OptiRough, Avoidance was not applied when the entire solid wasselected.

R-13147

Mill-Turn Exporting an operation to a Mill-Turn operations file failed. R-13812

Mill-Turn Work Offset field was not available on theMill Setup page. R-13781

Toolpaths Setup Sheet,Minimum andMaximum values were incorrect when the WCS wasdifferent from Tplane and Cplane.

R-13139

Toolpaths Manager Deleting nested empty toolpath groups failed. D-31528




API NET-Hook Drill operation commit method did not respect the supplied flag. D-29223

API Canceling out of theMetafile C-Hook, File Selection dialog put the graphics win-dow in an unusable state.

D-26921

API Solid entities were not properly deleted using the NET-Hook API. D-24180

API IsEvaluationLicense functionality was missing from NET-Hook API. R-10458

ATP Edits made to an operation via the Strategy Explorerwere not saved. R-13407


An error occurred when selectingQuick Verify. D-30353


A collision with a workpiece was not reported in Verify. D-30176


Mastercam Simulator's Remove chips option did not work as in the previous ver-sion.

D-28552


Mill-Turn Mastercam Simulator showed a gouge, whereMastercam Simulatorand Backplot did not.

D-26993


When using Sync Views inMastercam Simulator, a part would sometimes be outof view.

D-26992


Lathe Face Drilling was in the wrong position inMastercam Simulator. D-26982


Rapid moves disappeared as the toolpath ran in Classic Backplot. D-25474


Classic Backplot buttons needed a double-click to work. D-24763


Multiaxis Link Tool Change, Before Linking did not show correctly in ClassicBackplot.

D-24508


True Thread mode option was incorrectly selected by default inMastercam Sim-ulator.

D-24474


Tool Tip Compensation for a 5-axis Drill transform was shown incorrectly in Clas-sic Backplot.

D-18205


Tool from DXF file showed a gap between holder and tool in Classic Backplot. R-11618


Classic Backplotwas not fully cutting a Lathe Groove toolpath. R-11106


When in Classic Backplotwith Toolpaths Manager set to Auto-Hide, the playbackcontrols were hidden and unusable.

R-10968


The Simulationmode ofMastercam Simulator now displays collision items in red. S-49615

Configuration Invalid File Namemessage appeared when selecting the Default Machines. R-10153


16

17


Configuration Plane WCS gnomon has been changed to Plane on the System Configuration,Colors page.

S-50490

Drafting Note using a TrueType font displayed at a lower resolution. R-13203

General Design-only error message appeared whenMachine Group was present uponFile,Open.

R-13036

General Import Operations did not support .emcam and .emcx file types. R-09298

General Crash could occur when logging system errors. D-30351

General Files no longer shipped were not migrated from previous versions. D-29720

General Importing a certain KeyCreator file consumed RAM while being processed. D-26986

General Raster To Vector took longer to convert a file than in Mastercam X9. D-24332

General STEP files created in Creo were missing faces when read into Mastercam. D-22488

General Renumber level did not work correctly on a STEP file. R-13761

General CAD Import SOLIDWORKS did not create all the holes with Import SolidsHistory.

R-13750

General Verify Selection did not always show the preview. R-13186

General With AutoSave selected, saving after every operation with a 2D Dynamic Milltoolpath locked upMastercam.

R-13173

General Improved performance with a part file containing large amounts of geometry data. R-13120

General Imported DXF profile arcs were changed from bottom to top view when importingand extracting profiles.

R-11258

General Create Door, Export to separate file did not work. R-11257

General Merge Pattern causedMastercam to become unresponsive with certain functionsand plane settings.

R-11250

General Files with special characters in name would not open. R-04921

General Mastercam would not save to a folder named with foreign characters. R-04655

Geometry Using the Trim option in Blended Spline created bad results. R-10890

Geometry Extending a spline converted it into a parametric spline. R-07942

Interface Levels Manager had incorrect context menu behavior. R-11877

Interface Enable All has been changed to Restore Defaults in AutoCursor Settings. R-11471

Interface Delete key was not focused in Planes Managerwhen used inOrigin fields. R-10235

Interface Opening a part file changed theWCS/Tplane/CPlane settings. D-30203

Interface File opened with plane coordinate set to Lathe instead ofMill. D-26682

Interface Selecting a Quick Mask item did not change focus to the graphics area. R-13667

Interface Incorrect tool tip shown in Planes Manager right-click context menu. R-13654

Interface Lathe, Stock Plane did not change. R-13493

Interface Clear unpinned documents from recent file list triggered improper argumenterror and failed.

R-13432

Interface Plane information was not saved to the bookmark of the Viewsheet. R-13393



Interface The up/down scroll bar of the Planes and Levels Managers disappeared whenHide Plane Properties was selected.

R-13364

Interface Blanked entities were included in Fit. R-13269

Interface Blank/Unblank caused odd behavior with Select all entities by color. R-13269

Interface Levels were not getting updated in the Entity Attributes Manager. R-13264

Interface Right-click menu displayed incorrect string for Gview. R-13263

Interface AddingMachine selection to the Quick Access Toolbar disabled that machine inthe ribbon.

R-11775

Interface Not all levels were visible after opening a file. R-11585

Interface Pressing the [Delete] key when in the Comments field removed the Planes Man-ager.

R-11542

Interface Gview gnomon showed wrong plane name. R-11097

Interface Entities did not display whenmoved to a hidden level via Analyze. R-10924

Interface Moving entity used to define a plane broke the associativity. R-10109

Interface The Set all option in Printing, Linewidth Attributes dialog did not apply the linewidth to all colors.

R-09683

Interface The current Viewsheet was not preserved after the file was saved and reopened. R-09190

Interface Part did not always align or fit correctly after editing plane orientation. R-08570

Interface Reset all in Customize Keyboard allowed shortcut keys to appear in the contextmenu.

R-07996

Interface Plane sometimes showed incorrectly as Used in a Viewsheet. R-04674

Interface Updatedmachine images. S-50010

Lathe Some Lathe toolpaths displayed as rapids. D-29276

Lathe Classic BackplotwithQuick verify selected caused all tools to remove all stock. D-18777

Lathe Pickoff/Pull/Cutoff did not respect the tool choice. R-13389

Lathe Pickoff/Pull/Cutoff, ID jaws on right spindle caused geometry to be translated toincorrect Z location.

R-13134

Lathe A collision occurred when the Lathe Face options, Use stock and Finish stepoverwere enabled.

R-11802

Lathe Spindle direction was incorrect. R-11625

Lathe Lathe tool offset change in the operation’s parameters did not post the correct off-set.

R-11445

Lathe Lathe jaws and stock were not retained when defined on right chuck. R-11431

Lathe When exporting a Lathe operation as CSS, the operation stayed as RPM. R-11310

Lathe Compensation direction was wrong when using Lathe Z = World Z. R-11303

Lathe Lathe Dynamic Rough stock was not updated correctly. R-11255

Lathe Lathe Rough, Zig zag straight cuttingmethod collided with certain part shapes. R-11167

Lathe Lathe Cross Drill returned to the first position and re-drilled it. R-08889

Lathe Stock Flip had incorrect original position for chuck. R-08809


18

19


Lathe Enabling Extend start of passes in the Lathe Finish, Down Cutting dialog boxreset the Standoff distance value.

R-08295

Mill Tabbing between fields of 2D Peel Mill jumped around. D-08345

Mill Surface Finish Contour toolpath using an undercut tool did not undercut properly. R-13813

Mill Global,Minimum arc feed setting was not used. R-13502

Mill Surface Finish Contour using a lollipop tool withDetect Undercuts selectedcaused a warning.

R-13380

Mill Model Geometry page appeared empty for a 3D Project toolpath. R-13199

Mill Editing theModel Geometry grid changed the stock to leave amount to zero. R-13179

Mill A reporting computation error occurred when theMaximum stepover equaled theflat diameter of the tool.

R-13114

Mill 3D Hybrid toolpath did not create a toolpath when using 3D passes, Preserve Zpasses and Flat detection.

R-12979

Mill 3D Waterline with negative stock to leave had a long regeneration time. R-12954

Mill 2D Contourwithmultiple chains and using Control did not show compensationmove on both geometry.

R-11667

Mill 3D Waterline toolpath using a flat endmill with a negative value in Leave stock oncreated a computation error.

R-10716

Mill Dynamic OptiRough toolpath gouged a part when using a large Stepdown value. R-10549

Mill 3D Pencil toolpath cut deeper than theMaximum depth setting. R-09963

Mill Stockmodel did not create the model properly when there were many 3D HighSpeed Toolpaths selected.

R-06163

Mill-Turn Mill-Turn Pull position was invalid. R-13611

Mill-Turn Slot Mill added to theMilling ribbon gallery. R-13583

Mill-Turn MP.net—Adding array to watch list did not work from resource tree. R-11297

Mill-Turn MP.net—Else orphan was not detected. R-11296

Mill-Turn MP.net—// in literal string resulted in comment output when posting. R-11295

Mill-Turn Code Expert crashed when posting. R-11294

Mill-Turn MP.net—.DidOutput property was set incorrectly. R-11293

Mill-Turn Code Expert crashed whenOutput statements were made in anOutputCallBack. R-10986

Mill-Turn 3D Contourwas not supported inMill-Turn. R-10897

Mill-Turn Chuck jaw angle about C axis did not work on a sub spindle. R-09888

Mill-Turn ImportingMill-Turn operations brought in unnecessary planes. R-09863

Mill-Turn Lathe Groove, Finish spindle speed output incorrect NC code under a specificcondition.

R-09156

Mill-Turn Spindle sync did not work in both upper and lower streams. R-05209

Mill/Router Corrupt or Invalid file warning appeared when Engrave was the first toolpath cre-ated.

D-24635

Tooling Overall tool length was incorrect. D-30967



Tooling Problem tool holder causedMastercam to crash. R-13495

Tooling Tool Manager profile containedmissing 0.0001 line and failed inMastercam Sim-ulator.

R-11707

Tooling Error message was no longer issued withmultiple DbProviderFactories. R-11442

Tooling When editing a holder, the standard size warning appearedmultiple times. R-09991

Toolpaths Contour toolpath with tapered walls enabled did not import correctly. R-11767

Toolpaths Setup Sheets'white geometry did not displayed in images. R-13531

Toolpaths Feed rate and other properties in Analyze Toolpath did not update until afterregeneration.

R-11747

Toolpaths Code Expert's Region control context menu was missing when editing a PST post. R-10668

Toolpaths Mask on Arc, Sorting, Depth filtering overrode masked arc diameter. R-10184

Toolpaths The shortcut key for reverse chaining did not work until you clicked in the SolidChaining dialog box.

R-09529

Toolpaths Manual entry toolpaths caused errors in Simulation when they contained syncs. S-50473

Toolpaths Manager RegeneratingHigh Speed Toolpaths after usingModel Prep created newtoolpath groups.

R-11676

Toolpaths Manager Display Options, Dependencies, Selection setting was being used in the oper-ation-specific operation trees.

D-30753

Toolpaths Manager Changed default choice for the Partial NCI output filemessage toNo. R-11083

Toolpaths Manager Imported operations were marked dirty, making it difficult to see selections. R-10879

Toolpaths Manager Moving a toolpath group from one machine group to another did not list the tools inthe tool list.

R-09103

Toolpaths Manager Manual Entry operations were not marked dirty whenmodified. R-08661

Toolpaths Manager The Also renumber tools not used in any operation option was always selected. R-06330

Toolpaths Manager When using Edit Common Parameters the unchangedManual Entry operationswere marked dirty.

D-24364

Toolpaths Manager Renumber Tools in Lathe caused crash. R-13766

Toolpaths Manager The number of active teeth changed when a Thread Mill operation was imported. R-11876

Toolpaths Manager Parameters opened slower when a solid model was visible. R-10956

Toolpaths Manager Added support for multiple line comments in theMachine Group, Comments box. R-10176

Toolpaths Manager Toolpaths Managerwent blank for a period of time during toolpath regenerationwhen a solid was visible.

R-08478

Toolpaths Manager Improved the state of operation display when operations are collapsed. R-08236

Wire New planes were created upon wire toolpath regeneration. R-11932


20

ATTENTION! UPDATES MAY BE AVAILABLE.PLEASE REFER TO MASTERCAM.COM/SUPPORT FOR THE LATEST

DOWNLOADS.

https://www.instagram.com/mastercamcadcam/http://i.youku.com/Mastercamhttps://www.instagram.com/mastercamcadcamhttps://plus.google.com/u/0/112469607931783596009https://www.youtube.com/user/MastercamCadCamhttps://twitter.com/Mastercamhttps://www.facebook.com/Mastercam

IntroductionMastercam 2019BETA 5 04/12/2018BETA 4 03/22/2018BETA 3 03/01/2018BETA 2 02/08/2018BETA 1 01/25/2018Technical Preview 12/28/2017Technical Preview 11/30/2017Technical Preview 11/09/2017Technical Preview 10/19/2017Technical Preview 09/28/2017Technical Preview 09/07/2017

Mastercam 2019 ReadMe - Support Services | CAD CAM...BETA101/25/2018 Category Name Number...

Documents

Transcript of Mastercam 2019 ReadMe - Support Services | CAD CAM...BETA101/25/2018 Category Name Number...