Mark V ProVis - Edomed - · PDF fileMark V ProVis ™ SPECIFICATIONS ... 7-77 kg/sq cm...
4
Mark V ProVis ™ SPECIFICATIONS Medrad ® reserves the right to change product designs and specifications at any time in the continuing effort to improve their products. The following specifications refer to new units operating at room temperature (approximately 70 degrees F or 21 degrees C). INJECTOR HEAD Load Speed Forward or reverse 5-10 ml/sec. Syringe Heater 37° C (98° F) nominal Syringes Disposable: 60 ml, 150 ml or 200 ml Automatic Automatically sets higher than the Mechanical Stop selected volume before each injection: 1.5 ml with a 60 ml syringe 2.5 ml with a 150 ml syringe 4.0 ml with a 200 ml syringe WEIGHT Pedestal System (total) 213 lbs (97 kg) Injector Head 21.5 lbs (9,8 kg) Pedestal System (without head) 191.5 lbs (87,2 kg) Control Room Console (excluding head) 45 lbs (20,4 kg) Remote Control Panel (without cable) 10.5 lbs (4,8 kg) POWER REQUIREMENTS Available: 95-105 VAC, 50 or 60 Hz, 8 A typical 10 amp max 105-120 VAC, 50 or 60 Hz, 8 A typical 10 amp max 120-125 VAC, 50 or 60 Hz, 8 A typical 10 amp max 190-210 VAC, 50 or 60 Hz, 4 A typical 5 amp max 210-240 VAC, 50 or 60 Hz, 4 A typical 5 amp max 240-250 VAC, 50 or 60 Hz, 4 A typical 5 amp max (Typically defined at 15 ml/s with pressure of 600 psi) INJECTOR Flow Rate Syringe Size Flow Rate 60 ml syringe 0.3 to 10 ml/s, ml/min, ml/hr in 0.1 increments 10 to 20 ml/s, in 1 ml increments 10 to 59 ml/min, ml/hr in 1 ml increments 150 ml and 0.3 to 10 ml/s, ml/min, ml/hr in 200 ml syringes 0.1 increments 10 to 50 ml/s in 1 ml increments 10 to 59 ml/min, ml/hr in 1 ml increments Accuracy ± 5% and ± .25 ml/s and ml/min ± 10% and ± .25 ml/hr Rise/Fall Time Flow Rate 0.0 to 9.9 secs in 0.1 s increments Volume Maximum programmable Volume is limited only by syringe capacity. Minimum programmable Volume: 60 ml syringe 0.5 ml minimum, 150 ml and 200 ml syringe 1.0 ml minimum 0.1 ml increments with either syringe size. Pressure Limit In ml/s Flow scale, Pressure can be set to the following limits: 60 ml syringe 150 ml syringe 200 ml syringe 100-1100 psi 100-1200 psi 100-1000 psi 6-75 ATU (bar) 6-82 ATU (bar) 6-68 ATU (bar) 7-77 kg/sq cm 7-84 kg/sq cm 7-70 kg/sq cm 689-7584 kPa 689-8274 kPa 689-6895 kPa Pressure can be selected in increments of 1 for any scale (1 psi, 1 ATU (bar), etc.) In ml/min or ml/hr Flow scales, the maximum selectable Pressure is: 700 psi 48 atu (bar) 49 kg/sq. cm 4826 Kpa Delay Timer 0-99.9 seconds in increments of 0.1 second X-Ray Control Pair of normally-open isolated contacts rated to switch 10 A maximum at 28 VDC Program Up to 49 Single-Level injections, or 33 Multiple- Control Level injections Level Control Up to 4 levels (Flow Rate and Volume changes) per injection (single Flow scale only). ELECTRICAL LEAKAGE Earth <100 MA at 120 VAC <300 MA at 240 VAC Chassis <100 MA Patient <10 MA Protection Per EN 60601-1, designated as Class 1 Against Electrical Shock equipment with CF applied parts EMI/RFI Classified as Group 1, Class B equipment per EN 60601-1-2 CORD LENGTHS Power Cord Rack Mount 11 ft (3,3 m) Pedestals 15 ft (4,6 m) Film Changer Extension 25 ft (7,6 m) Cable RMC 100 I Auxillary Handswitch and Cable 25 ft (7,6 m) KMA 550IR Handswitch with Coiled 25 ft (7,6 m) Cable RPA 550IR Injector Head Cable 7 ft (2,13 m) pedestal std. 10 ft (3,05 m) Rack Mount std. in Americas/Asia 15 ft (4,6 m) std. in Europe and Japan
Transcript of Mark V ProVis - Edomed - · PDF fileMark V ProVis ™ SPECIFICATIONS ... 7-77 kg/sq cm...
Mark V ProVis™
SPECIFICATIONSMedrad® reserves the right to change product designs and specifications at any time in the continuing effort to improvetheir products. The following specifications refer to new units operating at room temperature (approximately 70 degrees For 21 degrees C).
INJECTOR HEAD
Load Speed Forward or reverse 5-10 ml/sec.Syringe Heater 37° C (98° F) nominal
Syringes Disposable: 60 ml, 150 ml or 200 mlAutomatic Automatically sets higher than the
Mechanical Stop selected volume before each injection:1.5 ml with a 60 ml syringe2.5 ml with a 150 ml syringe4.0 ml with a 200 ml syringe
WEIGHT
Pedestal System (total) 213 lbs (97 kg)Injector Head 21.5 lbs (9,8 kg)
Pedestal System (without head) 191.5 lbs (87,2 kg)Control Room Console (excluding head) 45 lbs (20,4 kg)
Remote Control Panel (without cable) 10.5 lbs (4,8 kg)
POWER REQUIREMENTS
Available:95-105 VAC, 50 or 60 Hz, 8 A typical 10 amp max
105-120 VAC, 50 or 60 Hz, 8 A typical 10 amp max120-125 VAC, 50 or 60 Hz, 8 A typical 10 amp max190-210 VAC, 50 or 60 Hz, 4 A typical 5 amp max210-240 VAC, 50 or 60 Hz, 4 A typical 5 amp max240-250 VAC, 50 or 60 Hz, 4 A typical 5 amp max(Typically defined at 15 ml/s with pressure of 600 psi)
INJECTOR
Flow Rate Syringe Size Flow Rate
60 ml syringe 0.3 to 10 ml/s, ml/min, ml/hr in0.1 increments
10 to 20 ml/s, in 1 ml increments10 to 59 ml/min, ml/hr in 1 ml
increments
150 ml and 0.3 to 10 ml/s, ml/min, ml/hr in200 ml syringes 0.1 increments
10 to 50 ml/s in 1 ml increments10 to 59 ml/min, ml/hr in 1 ml
increments
Accuracy ± 5% and ± .25 ml/s and ml/min± 10% and ± .25 ml/hr
Rise/Fall TimeFlow Rate 0.0 to 9.9 secs in 0.1 s increments
Volume Maximum programmable Volume is limited only bysyringe capacity. Minimum programmable Volume:60 ml syringe 0.5 ml minimum, 150 ml and 200 ml syringe 1.0 ml minimum0.1 ml increments with either syringe size.
Pressure Limit In ml/s Flow scale, Pressure can be set to thefollowing limits:
60 ml syringe 150 ml syringe 200 ml syringe
100-1100 psi 100-1200 psi 100-1000 psi6-75 ATU (bar) 6-82 ATU (bar) 6-68 ATU (bar)7-77 kg/sq cm 7-84 kg/sq cm 7-70 kg/sq cm689-7584 kPa 689-8274 kPa 689-6895 kPa
Pressure can be selected in increments of 1 forany scale (1 psi, 1 ATU (bar), etc.)
In ml/min or ml/hr Flow scales, the maximumselectable Pressure is:700 psi48 atu (bar)49 kg/sq. cm4826 Kpa
Delay Timer 0-99.9 seconds in increments of 0.1 second
X-Ray Control Pair of normally-open isolated contacts rated toswitch 10 A maximum at 28 VDC
Program Up to 49 Single-Level injections, or 33 Multiple-Control Level injections
Level Control Up to 4 levels (Flow Rate and Volume changes)per injection (single Flow scale only).
ELECTRICAL LEAKAGE
Earth <100 MA at 120 VAC<300 MA at 240 VAC
Chassis <100 MAPatient <10 MA
Protection Per EN 60601-1, designated as Class 1Against Electrical Shock equipment with CF applied parts
EMI/RFI Classified as Group 1, Class B equipmentper EN 60601-1-2
CORD LENGTHS
Power Cord Rack Mount 11 ft (3,3 m)Pedestals 15 ft (4,6 m)
Film Changer Extension 25 ft (7,6 m)Cable RMC 100 I
Auxillary Handswitch and Cable 25 ft (7,6 m)KMA 550IR
Handswitch with Coiled 25 ft (7,6 m)Cable RPA 550IR
Injector Head Cable 7 ft (2,13 m) pedestal std.10 ft (3,05 m) Rack Mountstd. in Americas/Asia15 ft (4,6 m) std. inEurope and Japan
90˚ 21˚
12˚0 0
10"(25,4 cm)
50.7"(128,8 cm)
58"(147,3cm)
55"(139,7
cm)
50.4"(128cm)
24.5" (62,2 cm)
26.6" (67,6 cm)
60"(152,4 cm)
180˚
205˚
26.3"(66,8 cm)
5.3"(13.5 cm) 4.9"
(12.4 cm)
22.6"(57.5 cm)
14.5"(36.8 cm)
7.2"(18.2 cm)
10.8"(27.5 cm)
DIMENSIONS
12"(30.5 cm)
9.3"(23.6 cm)
Top
16.875" (43 cm)
12.625"(32 cm)
10.5"(27 cm)
19" (48 cm)
2 in.(5,08 cm)48.5 in.
(123,19 cm)
26.75 in.(67,95 cm)
35.6 in.(90,42 cm)
▲ Injector Head PedestalKMA 320 RT
▲ Table BracketKMA 350Accomodates rails 7/8” – 1-1/4” wide (1.91 cm – 3.18 cm)
HEAD MOUNTING SYSTEMS
* 50 ft. (15.2 m) and 75 ft. (22.9 m) Remote Panel Cables are also available** 60 ft. (18.3 m) and 75 ft. (22.9 m) Injector Head Extension Cables are also available
Remote Control Panel
Power Cord
Electronics Box
Remote Panel Cable (100 ft. [30.5 m])*
RPC 100P-100 Injector Head Extension Cable (100 ft. [30.5 m])**KMA 950-S100 I
Table BracketKMA 350Height Range: 12"-17" (30.48 cm - 43.18 cm)
T
V
26" (66 cm)
USE 12-3/8" Ø BOLTSTO CEILING SUPPORTSTRUCTURE(BY ENGINEER OF RECORD)
T
V
26" (66 cm)
T
V
26" (66 cm)
24.7" (63 cm)
T
V
26" (66 cm)
C.G. WT. =138 LBS(63 Kg)
43.4
"(1
10 c
m)
T
V
26" (66 cm)
T
V
HEAD MOUNTING SYSTEMS
Max.
32" (
81 c
m)
or 1
9" (4
8 cm
)*
46" (
117c
m)
or 2
5" (6
4 cm
)*
AccessoryMount
Min.
2.5"6,4 cm
18 cm15 cm
7"6"
31.5"80 cm
1.5" 4 cm
360°
360°
360°
3.5" - 9 cm high pinwith cover
45°
50°
2.5"6,4 cm
4.5"11,4 cm
28"71 cm
31.5"
80 cm
▲ Ceiling Mounted CounterpoiseOCS 115A Weight: 27 kg (60 lbs)
70.5"179 cm
Required for fullyextended rotation
31.5"80 cm
45°
50°
1.5"3,8 cm
31.5"80 cm 22"
56 cm
Wall
57"145 cm
2.5"6,4 cm
4.5"11,4 cm
28"71 cm
80"203 cm
Floor
3.5"9 cm
▲ Wall Mounted CounterpoiseOCS 125A Weight: 18 kg (40 lbs)
All weights are without injector head.
� Support Arm OnlyOCS 135AWeight: 16 kg (35 lbs)Used when an existing ceilingcolumn is in place.
� Mobile Ceiling Mounted CounterpoiseOCS 155AWeight: 44 kg (97 lbs)
NOTES: 1. Forces are determined per California Building Code, Section 1630A
and Table 16A-0.Horizontal acceleration (VH) = 0.45WVertical acceleration (VV)= 0.15W
2. Forces are maximums, and occur when equipment is moved to themost eccentric position.
3. Provide ceiling structure designed to support weights and forcesshown. (By engineer of record for building).
*with optional short ceiling mount
Medrad, Inc. Corporate Office
One Medrad DriveIndianola, PA 15051-0780 U.S.A.
Telephone: (412) 767-2400FAX: (412) 767-4128
Web Site Address:www.medrad.com
MKVPV SPEC USA 200112
®
Medrad reserves the right to modify the specifications and features described herein, ordiscontinue manufacture of the product described at any time without prior notice orobligation. Please contact your authorized Medrad representative for the most currentinformation.
The only source for Medrad Engineering, MedradQuality, Medrad Service and Medrad Support. Medrad is dedicated to continually improving the quality of all our
products and services such that our customers’ satisfaction, loyalty, and respect areunsurpassed. It is our policy to clearly understand and agree upon the valid require-ments of the work we perform for our customers, both internal and external, and topursue 100% conformance to those requirements...on time, every time.
Qualityfor Life
®
Medrad, Inc. is EN-ISO 9001/EN 46001 Certified
Medrad, Quality for Life, Q and design are federally registered trademarks and Mark VProVis is a trademark of Medrad, Inc. U.S.A.
Printed in U.S.A. ©1999 Medrad, Inc. All Rights Reserved
