Manufacture of High Resistivity, Low Oxygen Czochralski Silicon June 2005 Olli Anttila Okmetic...
-
Upload
roberta-shepherd -
Category
Documents
-
view
222 -
download
0
Transcript of Manufacture of High Resistivity, Low Oxygen Czochralski Silicon June 2005 Olli Anttila Okmetic...
Manufacture of High Resistivity, Low Oxygen Czochralski Silicon
June 2005Olli Anttila
Okmetic Fellow,Okmetic Oyj
Manufacture of High Resistivity, Low Oxygen Czochralski Silicon
Outline• Background• Crystal growth and wafer manufacturing• Wafer characteristics• High resistivity CZ
•Metals and lifetime•Dopants•Oxygen•Magnetic field
• Silicon melt behavior • Conclusions
Okmetic Worldwide Presence
Market Overview
Electronic Equipment$ 1000 billion / + 8% *)Semiconductors$ 250 billion /+15 % *)
Silicon Wafers$ 8 billion /+13 % *)
Polysilicon $ 0,7 billion +14 % *)
*) 1970-2003 CAGR
© NOKIA MEGATRENDS.PPT / 16.11.1998 / EKu page: 6
Silicon wafers: Key process steps
• Wafer slice• final thickness
typically 500-600 µm
• Crystal Growth• bulk and some surface
material properties
• Wafer etch• remove damage• final backside
Silicon wafers: Key process steps
• Polish• to obtain excellent
flatness and surface properties
• Final Clean and Package• remove particle, metallic,
ionic, and organic contamination
• ensure dependable storage behavior
Okmetic Products
•Polished Cz-silicon wafers for microelectronics
•MEMS silicon wafers for micromechanics•Epitaxial wafers•SOI-wafers •Diameters: 100...200 mm•Dopants: boron, phosphorus, arsenic
and antimony
•Resistivity: 0.002…> 2 kOhm-cm•Orientations: 1-0-0, 1-1-1 and 1-1-0•oxygen: < 6…18 ppma•epi: high uniformity
high resistivity available
Czochralski (CZ) Crystal Growth
1. Polysilicon charge in silica crucible.
3. Shoulder growth, after neck is complete.
5. Body growth.
2. Start of neck. Seed is dipped to > 1400 °C melt.
4. Start of body, after completion of shoulder.
5. Conical tail growth after completion of body.
Czochralski (CZ) Crystal GrowthAtmosphere: low pressure, high purity argon.Hot zone: isostatic high purity graphite and graphite felt.
Manufacture of High Resistivity, Low Oxygen Czochralski Silicon
Outline• Background• Crystal growth and wafer manufacturing• Wafer characteristics: lifetime and metals• High resistivity CZ
•Metals and lifetime•Dopants•Oxygen•Magnetic field
• Silicon melt behavior • Conclusions
0.01
0.1
1
10
1010
at
/cm
2
FeNiCuZnCrD.L.
Process Capability: MetalsVPD-TXRF, Vantaa plant, Q4/2000 - Q1/2005, average values
Metal levels have been stable at or below detection limit of 1E9 at /cm2. Values include contamination from handling during sampling and measurement.
Q4/
200
0
Q1/
200
1
Q2/
200
1
Q3/
200
1
Q4/
200
1
Q1/
200
2
Q2/
200
2
Q3/
200
2
Q4/
200
2
Q1/
200
3
Q2/
200
3
Q3/
200
3
Q4/
200
3
Q1/
200
4
Q2/
200
4
Q3/
200
4
Q4/
200
4
Q1/
200
5
0.01
0.1
1
10
1010
at
/cm
2
FeNiCuZnCrD.L.
Process Capability: MetalsVPD-TXRF, Vantaa plant, Q4/2000 - Q1/2005, average values
Imagine that a coin is made to slide on a wafer, leaving a tail of 109 /cm2 metal atoms. This equals the typical contamination level of a state-of-the-art clean. Then on another wafer, and another, over and over again. After a while, the coin wears and it gets thinner. How far should we make the coin go, before it is all used up???
Lifetime as-oxidized, during past 24 months
• specification > 500 cm• both n- and p-type• no specific emphasis on surface passivation
0.0
1000.0
2000.0
3000.0
4000.0
5000.0
6000.0
7000.0
8000.0
9000.0
10000.0
1 4 7 10 13 16 19 22 25 28 31 34 37 40 43 46 49
lifet
ime
(s)
average
80 % of area
CZ vs. FZ MATERIALfor high frequency and detector applications
• FZ comes naturally oxygen lean• high resistivity readily available with FZ
So, why look into CZ
• CZ available in larger diameters
• lower wafer cost
• better compatibility with advanced CMOS processes
• oxygen brings significant improvement in thermal slip resistance
• oxygen gives significant radiation hardness advantage?
CZ vs. FZ MATERIALfor high frequency and detector applications
Does CZ fulfill the requirements?
• dopant control?
• oxygen related donors?
• metallic contamination? !YES!
• recombination lifetime / diffusion length? !YES!
• COP’s?
Metals in silicon
Imagine that a coin is made to slide on a wafer, leaving a tail of 109 /cm2 metal atoms. This equals the typical contamination level of a state-of-the-art clean. Then on another wafer, and another, over and over again. After a while, the coin wears and it gets thinner. How far should we make the coin go, before it is all used up??? From the Earth to the Sun, 150 million km!!
Another quiz: Common metallic contaminants in grown crystal appear typically at 10 ppqa (parts per quadrillion atomic) level. That is 0. and how many zeros??
CZ vs. FZ MATERIALfor high frequency and detector applications
Does CZ fulfill the requirements?
• dopant control?
• oxygen related donors?
• metallic contamination? !YES!
• recombination lifetime / diffusion length? !YES!
• COP’s?
HIGH RESISTIVITY MATERIAL: 6”P100normal crucible quality
6" P100: 106990
200
300
400
500
600
700
800
0 500 1000 1500
Distance from seed/mm
Re
sist
ivity
/Oh
m c
m
• Intentional doping at about 1600 Ohmcm level at seed end.
•Typical seed-to-tail resistivity ratio is about 1.5; here much larger.
•High crucible boron (& Al) content results in < 1 kOhmcm material.
HIGH RESISTIVITY MATERIAL: 6”P100synthetic crucible
• special SiO2 coating• resistivity at seed end is higher due to oxygen donors• boron contamination in some critical graphite parts
6" P100: 120605
600
800
1000
1200
1400
1600
1800
0 500 1000 1500
Distance from seed/mm
Re
sist
ivity
/Oh
m c
m
HIGH RESISTIVITY MATERIAL: 150 mmAppr. attainable reproducible resistivityvs. crystal length
0
1000
2000
3000
4000
0 500 1000 1500 2000
Distance from seed /mm
Re
sist
ivity
/O
hm
cm
p-typen-type
• MCZ growth• high purity silica
crucible• polysilicon grade
comparable to high resistivity FZ
• high level of control on hot zone purity
CZ vs. FZ MATERIALfor high frequency and detector applications
Does CZ fulfill the requirements?
• dopant control? !YES?
• oxygen related donors?
• metallic contamination? !YES!
• recombination lifetime / diffusion length? !YES!
• COP’s?
HIGH RESISTIVITY CZ MATERIAL
• low interstitial oxygen mandatory• oxygen donors created during crystal
growth and device process• critical temperature appr. 450 °C• donors annihilated > 600 °C• back-end-of-the-line (BEOL) temperatures
between 400 and 500 °C to be avoided• e.g., at 420 °C, only 10-30 min allowed,
depending on Oi and resistivity• typical Oi 5-8 ppma for high res. material
Oxygen control parameters
• Gas flow• pressure• purge tubes (gas flow
pattern• crucible rotation• crystal rotation• temperature
distribution• magnetic field
MCZ Puller
• Vacuum system operating at above 1400 °C offers electrical power control, mechanical movements and gas flows. Argon purge pressure is typically 20-30 mbar.
• The I.D. of the magnet > 1 m, max. power range 100 kW.
MCZ stabilizes the melt and has some influence on oxygen level
• magnet used by Okmetic results to somewhat higher oxygen level than regular CZ
• better melt stability widens oxygen range; more aggressive control parameters can be used
Results from early crystals ~10 yrs. ago
0
2
4
6
8
1 2
1 4
1 8
2 0
0 2 0 4 0 6 0 8 0 1 0 0
d istan ce fro m seed (cm )
1 2 0 1 4 0 1 6 0 1 8 0 2 0 0
1 0ox
ygen
con
cent
rati
on (
ppm
a) 1 6re g u la r
C Z
Magnetic field changes oxygen behavior
• thicker laminar layer next to crucible wall => slower oxygen dissolution
• thicker laminar layer at gas interface => tendency to increase oxygen in the melt
• balance between these two effects defines oxygen level
• slow crucible erosion => long crucible lifetime, low dopant emission rate
• price to pay: more difficult control of radial variations! Both dopants and oxygen
CZ vs. FZ MATERIALfor high frequency and detector applications
Does CZ fulfill the requirements?
• dopant control? !YES?
• oxygen related donors? !YES?
• metallic contamination? !YES!
• recombination lifetime / diffusion length? !YES!
• COP’s? remains unresolved at this point, and
should be addressed later, if needed; typical density < 1E6 /cc.
HIGH RESISTIVITY MATERIAL: 150 mm
0
1000
2000
3000
4000
0 500 1000 1500 2000
Distance from seed /mmR
esi
stiv
ity /
Oh
m c
m
p-type
n-type
• > 2 kOhmcm P-type material manufacturable• 100 mm material allows somewhat higher values• n-type resistivity about factor 2 lower• oxygen < 8 ppma
Measument of Resistivity 4-Point Probe
• ~ 2000 cm p-type• proper value only at very low current (avalanche
injection!)• measurement stability major issue
-20
-10
0
10
20
-2E-3 -1E-3 0E0 1E-3 2E-3
Current [A]
Vol
tage
[V
]
000E+0
4E+3
8E+3
12E+3
16E+3
Res
ista
nce
[Ohm
]
I
U
Manufacture of High Resistivity, Low Oxygen Czochralski Silicon
Outline• Background• Crystal growth and wafer manufacturing• Wafer characteristics: lifetime and metals• High resistivity CZ
•Metals and lifetime•Dopants•Oxygen•Magnetic field
• Silicon melt behavior • Conclusions
Characteristic data
+ crucible diameter ~0.5 m+ crystal diameter 100-300 mm (300
mm)+ about 100 kg in the beginning of
process (several 100’s of kg)+ melting temp 1412 °C+ kinematic viscosity very low 2.8 E-7
m2/s+ Prandtl number very low 0.011+ crystal rotation 10-30 rpm+ crucible rotation 2-20 rpm+ typical Grashof number high 1E10+ typical crystal Reynolds number
some 10’s of thousands
Magnetic field effectPerpendicular velocity field (m/s)
200
A50
0 A
1000
A
• Strongest field at crucible corner
• flow suppressed by strong field
=> growth effectively from smaller, less unstable melt
• under crystal, minor impactdopant, oxygen
distribution is not uniform even with MCZ
Melt flow is buoyancy driven turbulent
The melt behavior is not quite so smooth…
Recombination Lifetime After Oxygen Precipitation125 mm N(100), 850 °C / 4h + 1000 °C /12 h O2
•shorter lifetime where more precipitates
•ring diameters give time scale, together with freezing interface curvature
•quasiperiodic behavior, time scale ~1 min
• ~ open hot zone, early 90’s
•behavior is not external pull rate related
LPS measurement on 150 mm N(100) 5 Ohmcm crystal
• area shown 100 x 50 mm
• sample as-grown and donor kill annealed
• freezing interface shape nicely visible
• time dependent freezing velocity can be measured if spectral response of measurement is known
sample cut
Growth axis
Silicon Melt Modeling:Temperature Distributionand Velocity Field
•crucible rotation 5 rpm • time dependent, chaotic
behavior•heat to the crystal largely from
the bottom
It was at a meeting of the British Association in London in 1932 that I remember Hoarce Lamb remarked:
“I am an old man now, and when I die and go to Heaven there are two matters on which I hope for enlightenment. One is quantum electrodynamics, and the other is the turbulent motion of fluids. And about the former I am really rather optimistic.”
– Sir Sydney GoldsteinAnnual Reviews of Fluid Mechanics, Vol. 1 (1969), p. 1
Turbulence
Modeling: Oxygen distribution in melt
• relatively large radial gradients in the melt
• well mixed melt poor assumption
• classical explanation for lower oxygen in tail needs reconsideration
• oxygen slow diffuser, contrary to heat
=> no direct connection between oxygen and dopant striations
50 slpm@20 mbar
Conclusions
•Main issues in high resistivity CZ material •metallic contamination•lifetime•dopant level•oxygen level
have been solved to satisfactory / reasonable level
•magnetic Cz and tight control of dopant contamination mandatory
•naturally appearing oxygen offers some advantages
•ample space for further developments
Manufacture of High Resistivity, Low Oxygen Czochralski Silicon
June 2005Olli Anttila
Okmetic Fellow,Okmetic Oyj