Manual Xwave 5000 Eng
Transcript of Manual Xwave 5000 Eng
-
7/21/2019 Manual Xwave 5000 Eng
1/32
Operang Instrucons
5.1CH DIGITAL MPEG4 PLAYER
Xwave 5000
Please read carefully before operation
-
7/21/2019 Manual Xwave 5000 Eng
2/32
- 1 -
CAUTION: To avoid electric shock, do not remove t he top or the bottom
cover, or repair the unit by yourself. Please have it f ixed with eligible engineers.
To avoid luring danger of electric
shock, do not touch any parts
that are uninsulated.
Do not repair it by yourself
without repairing instructions.
CAUTION: To avoid fire and electric shock, do NOT expose
the unit in rain or place of high humidity.
MIND ELECTRIC SHOCK
DO NOT OPENCAUTION
SAFETY INSTRUCTIONS
Installation and safety precaution
Keep away from heat, humidity, dust,
and objects that vibrate
Do NOT locate the unit in places of high temperature
or humidity, such as areas nearing the radiator, oven,
etc, and places dusty or close to vibrating objects.
Drastic shocks can also result in damages to the unit.
Hence, be gentle and careful while moving the unit.
Store the unit under ventilation
Store the unit in well
ventilated place; avoid
leaving objects around
the vent of the unit.
To avoid fire accident, there should be at
least 10CM space between the ambient
objects and the rear panel and the right
and left sides of the unit; and at least 20CM
space from the top surface.
Use standard outlet
1. High-tension AC, as the current for air-
conditioners, can cause danger, damages
of the unit, or a fire.
2. Do NOT use DC, especially on a ship
or other places where DC is used.
3. To avoid electric shock, please use
appropriate plug and suitable socket
Unplug from electricity if the unit
is not to use in long term
As long as the power
cord is connected to
the socket, despite
that the unit is turned
off, it is still connected
to 220V high tension AC. Hence, please unplug
the outlet if you decide not to use it in a long time.
Power Cautions: do not open!
CAUTION!
Do not repair the unit by yourself or re-systemise it.
There are no spare parts provided for such case.
Reparation has to be performed by professional
electricians. Self-repairing and relocation of any
internal parts can generate further difficulty for the
engineers and cause danger for the unit as well as
for yourself.
PRECAUTION!
Do NOT let your kids insert any objects into the
unit,
especially metallic objects. Coins, screws and other
small metallic items can cause serious electric
shock or misfunction. If water is found splashed
into
the unit, it can cause serious electric shock and fire.
In this case, please first disconnect the power andhandle carefully. Insect spray, ethyl products, and
thinner can age the plastic parts and deform the
appearance of the unit. In occasions, spray can even
lead to a fire accident.
-
7/21/2019 Manual Xwave 5000 Eng
3/32
- 2 -
SAFETY INFORMATION
Installation Warnings
Ventilation Slots and openings in the case are provided for ventilation to ensure reliable operation of the video
product and to protect it from overheating. These openings must not the blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or heat register. This product should not be placed in
a built-in installation such as a bookcase or rack, unless proper ventilation is provided or the video product
manufacturer instructions have been followed.
Power Lines :An outside antenna system should not be located in the vicinity of overhead power lines, other
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching or approaching such power lines or circuits,
as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to a
professional antenna installer.
Lightning :For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the video product due to lightning and power line surges.
Compulsory Warnings
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified
person, in order to avoid a hazard. This product has not been designed for any uses other than those specified in
this booklet.
Laser Safety
This compact disc player is classified as a CLASS 1
Laser Product.
Only qualified service personnel should remove the cover or attempt to service this device due to possible eye
injury. Invisible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
-
7/21/2019 Manual Xwave 5000 Eng
4/32
- 3 -
TABLE OF CONTENTS
SAFETY INSTRUCTIONS......1
SAFETY INFORMATION...2
TABLE OF CONTENTS.3
GENERAL INFORMATION..4-5
Setup precautions..4
Accessories supplied.4
Cleaning discs4
About recycling.. ..4
DISC type which can be played ...5
How to deal with disc....5
MAIN UNIT6-8
Front Panel6
Rear Panel..7
Remote Control.. ..8USING THE REMOTE CONTROL..9
Basic instruction9
SYSTEM CONNECTIONS...10-13
Basic stereo sound connections.10
Surround sound connections..11
Video connection..12
Power13
GETTING STARTED14-17
Turning on the DVD system.14
Setting language preferences14
On-screen display (OSD) language..14
Audio, Subtitle and Menu language for DVD playback...14
Setting the video display mode.16
Setting the subtitles in MPEG-417
DISC OPERATIONS.18-22
Playable discs....18
Region Codes for DVD discs18
Playing a disc....18
Basic playback controls.....19
Selecting various repeat functions....................................19
Other playback features for video discs (DVD/VCD/SVCD) ..20
DVD Setup Menu Options 23-27
Accessing the DVD setup menu...23General Setup Page...23
Audio Setup Page .24
Video Setup Page...24
Preference Page.26
Password setup page..26
MPEG4 Subtitle Setup Page..27
SOFTWARE UPGRADES..28
TROUBLESHOOTING....29
SPECIFICATIONS 30
-
7/21/2019 Manual Xwave 5000 Eng
5/32
- 4 -
GENERAL INFORMATION
CAUTION!
The machine does not contain any user-serviceable parts. Please leave all maintenance work to qualified
personnel.
Setup precautions
Finding a suitable location
Place the set on a flat, hard and stable surface. Do not place the set on a carpet.
Do not position the set on top of other equipment that might heat it up (e.g., receiver or amplifier)
Do not put anything under the set (e.g., CDs, magazines).
Install this unit near the AC outlet where the AC power plug can be easily reached.
Space for ventilation
Place the apparatus in a location with adequate ventilation to prevent
internal heat build up. Allow at least 10 cm (4.5) clearance from the
rear and the top of the set and 5cm (2.3) from the left and right to
prevent overheating.
Avoid high temperatures, moisture, water and dust
Apparatus must not be exposed to dripping or splashing.
Do not place any sources of danger on the apparatus (e.g., liquid filled objects, lighted candles).
Accessories supplied
Remote control with batteries AV cable User manual Warranty cardCleaning discs
Some problems occur (frozen picture, sound disruptions, picture distortions) because the disc inside the unit is
dirty. To avoid these problems, discs should be cleaned on a regular basis. To clean a disc, use a micro fi bre
cleaning cloth and wipe the disc from the centre to the edge in a straight line.
CAUTION!
Do not use solvents such as benzene, thinner, commercially available cleaners, or anti-static sprays
intended for discs
About recycling
These instructions have been printed on non-polluting paper. The electronic equipment contains a large number of
materials that can be recycled. If you are disposing of an old machine, please take it to a recycling centre. Please
observe the local regulations regarding disposal of packaging materials, exhausted batteries and old equipment.
-
7/21/2019 Manual Xwave 5000 Eng
6/32
- 5 -
GENERAL INFORMATION
DISC type which can be played:
.DVD disc with the possibility of the
single and repeated recording
.CD-R(W) with audio MP3 contents
.Video CD (VCD) .CD-R(W) with video JPEG contents
.Super Video CD (SVCD) .CD-R(W) with video MPEG4 (DiVX and XviD) contents
.DVD with the digital video recording .DVD with graphic files MPEG4 (DiVX and XviD) contents
.Audio CD
Helpful indication:
When you have problems with playing disc, please take it out and try another disc. Improper format discs will
not able to be played.
How to deal with disc
Highly data compaction is written in video CD. Thats why those discs require particular cautiousness and
care, when we touch them.
Take the CD disc in hands, holding edge/or through hole in the middle.
Do not touch the playback side of the disc by finger.
Do not perish or scratch this disc.
Do not put discs in places subject to direct sunlight or near heat sources.
Store discs vertically at cool dry place.
Do not store discs in places subject to moisture and dust.
Wipe the disc lightly with a soft cloth from the middle to the edge. Do not use any type of solvent spirit or
spray.
-
7/21/2019 Manual Xwave 5000 Eng
7/32
- 6 -
MAIN UNIT
Front Panel:
1. POWER but t on - Pr ess t o swi t ch t he set on or off .
2. 3 IN1 CARD SLOT Connect s wi t h t he car d.
3. USB PORT Connect s wi t h t he di gi t al medi a.
4. DI SC TRAY( DOOR) - Open t hi s door t o pl ace t he di sc.
5. OPEN/ CLOSE but t on - Opens and cl oses t he di sc t r ay
6. Remot e cont r ol s i gnal sensor - Recei ves t he s i gnal f r om t he REMOTE CONTROL
( ai m t he REMOTE t owar ds t hi s sensor )
7. DI SPLAY WI NDOW- shows wor ki ng st at us .
8. PLAY/ PAUSE but t on - Pr es s t o st ar t pl ayi ng t he DVD/ CD di sc or t o pause pl ayi ng
9. STOP- Used DVD menu, Pr ess t o open st op pl ay monent ar i l y or f ul l y.
10. SOURCE but t on - Thi s but t on i s set f or pl ayback shi f t bet ween DVD, USB devi ce and CARD.
Pr ess t hi s but t on repeat edl y t o change t he si gnal i nput s our ce f r om DVD t o CARD, t hen t o USB. If t he USB devi ce has several di sk ar ea, access t o di f f er ent ar eas
ar e t he ent er t ai nment f i l e, i ncl udi ng pi ct ur e f i l e as J PEG, audi o fi l es as MP3, WMA,
Vi deo f i l es as AVI et c, can be pl ayed di r ect l y by pr es s i ng ENTER or PLAY. Pr es s "SOURCE
key on t he r emot e cont r ol t o do t he same oper at i on.
Hint of USB/CARD reader connection: Xwave USB/ CARD r eader pl ayer can suppor t USB devi ce, such as MP3 pl ayer , Handdr i ve, HDD up t o
80G, and di f f er ent st orage car ds s uch as SD car d, MS car d, MMC car d at amazi ng r eadi ng speed.
Just connect your USB devi ce t hrough t he USB por t t o Xwave 5000, or i nser t t he card i nt o t he
card sl ot , t hen easi l y enj oy t he ent ert ai nment f un f r om your personal st or age devi ce.
-
7/21/2019 Manual Xwave 5000 Eng
8/32
- 7 -
MAIN UNIT
Rear Panel:
1. 5.1CH OUTPUT: Audio 5.1CH analog out2. S-VIDEO: S-Video output for better quality picture out3. VIDEO: Composite video out4. Pb/Cb Pr/Cr Y: Component allow to attain best quality video signal output5. COAXIAL: Digital coaxial audio out6. OPTICAL: Digital optical audio out7. SCART OUTPUT8. AC 100-220V 50/60Hz: Power cord
-
7/21/2019 Manual Xwave 5000 Eng
9/32
- 8 -
MAIN UNIT
Remote Control:
5. RESET Buon -Press to reset the system to factory default sengs.
22. SOURCE Buon - Pressing this buon repeatedly change the input source to
DVD,USB or Card.
4. MUTE Buon - Instantly turns off the sound. Press again to resume.
1. Power on / off
2. Subtle: Switch subtle
3. Angle: Switch play angle
6. DVD Menu: Enter DVD root menu
7. Setup: Enter player setup menu
8. Direcon buon ( )
9. Enter buon
10. Play/Pause buon ( )11. Number buons
12. Previous: Skip backward ( )
13. Next: Skip forward ( )
14. PBC: VCD PBC menu
15. Slow: Slow moon playback
16. Display: Display or hide play informaon17. Repeat: Repeat play
18. Open or close disc tray
19. Audio: Switch audio track
20. VOL +: Increase volume
21. VOL -: Decrease volume
23. Stop buon ( )
24. Goto: Play from the desired locaon
25. Fast forward buon ( )
26. Fast backward buon ( )
27. Zoom: Zoom in / out buon
28. Step: Play frame by frame
29. Video switch
30. A-B repeat play the selecon
-
7/21/2019 Manual Xwave 5000 Eng
10/32
- 9 -
USING THE REMOTE CONTROL
A Open the battery compartment.
B Insert two batteries type AAA, following the indications inside the
compartment.
C Close the cover.
D Point the remote control directly at the remote sensor (IR) on the front
panel.
E Select the source you wish to control
F Then select the desired function
CAUTION!
Remove batteries if they are exhausted or if the remote control is not to be used for a long time.
Do not mix batteries (old and new or carbon and alkaline, etc.).
Batteries contain chemical substances, so they should be disposed of properly.
Basic instruction:
Cautions! Be sure turn off power and unplug unit before connecting.
Different from other visual format, DVD provides you wide visual option, which allows on many devices
from standard TV with stereophonic out to home cinema system with projector and all spatial and caustic
possibilities.
Please read manual of every device carefully
Do not place any objects or any other device on DVD player,
Be sure wither the cable is connected properly,
The DVD player shall be directly connected to the TV or other audio receiver. Any other connection could
cause distortion.
Hereinafter we introduce several options of sound and picture connection with DVD. Choose one of the
options. (Dont combine them together).
-
7/21/2019 Manual Xwave 5000 Eng
11/32
- 10 -
SYSTEM CONNECTIONS
Basic stereo sound connections
Stereo sound connection to TV set
Stereo sound connection to stereo receiver
Use RCA Audio cable. Cable with red connector from sockets FR in the DVDplayer and Right Audio In in TV set or stereo receiver, while white connector
from sockets FL in DVD player and to Left Audio In in the TV set or stereo
receiver.
In connection from L/R with stereo TV set or stereo receiver, remember to
setup DOWNMIX status in Audio menu into STEREO. (See AUDIO SETUP Page)
-
7/21/2019 Manual Xwave 5000 Eng
12/32
- 11 -
SYSTEM CONNECTION
Surround Sound connection:
When you want to get surround sound effect, you need to connect DVD player to a mul-channel AV receiver to get
this sound effect by analog connecon or digital connecon.
Analog connecon:
- Use 6pieces of RCA cable, connect 6 connectors of DVD player rear panel (FL, FR, SL,
SR, CEN, SW) to the audio input socket of AV surround receiver. -In connecon of
analog mul channel, remember to setup DOWNMIX status in Audio menu into OFF.
(See AUDIO SETUP Page )
Digital connecon:
This is to get a beer audio effect. To do this kind of connecon, make sure that you have an AV receiver with built in
Dolby Digital decoder or DTS decoder, with Digital Opcal input socket, or Digital Coaxial i nput socket. -Use a
digital opcal cable, connect from OPTICAL output socket in DVD player, to OPTICAL input socket in AV receiver
- Use a digital coaxial cable, connect from COAXIAL output socket in DVD player, to COAXIAL input socket in AV
receiver. - In digital connecon, remember to setup SPDIF SETUP as RAW or PCM. (See AUDIO SETUP)
-
7/21/2019 Manual Xwave 5000 Eng
13/32
- 12 -
SYSTEM CONNECTIONS
Cautions! (Refer to optical cable connection)
Before connecting, shuck the bung dustproof from the ending of optical cable. Put in jack in amplifier and
player orderly. Retain bung and cover the ending of the cable and cable many times that the cable will be took
out from the socket.
DONT CONNECT OPTICAL CABLE OR COAXIAL CABLE TO DEVICE, WHICH DOESNT
HAVE BUILT-IN DECODER DOLBY DIGITAL.THE DIFFENCE OF OUTPUT SIGNALS, MAY
CAUSE SERIOUS DAMAGE TO BOTH DEVICES.
VIDEO connection
Composite video connection
- Use the yellow RCA cable to do composite video connection, which is of a normal video signal. PutYellow RCA end from VIDEO output socket from DVD player, to VIDEO input socket in TV set or AV
receiver.
- Remember to press VIDEO SW on remote control to change to OFF status. Or go to VIDEO SETUPPAGE to set the COMPONET as OFF.
S-Video connection
- Use the S-Video cable to connect, which is of a higher video signal. Put one side end from S-VIDEOoutput socket from DVD player, to S-VIDEO input socket in TV set or AV receiver.
- Remember to press VIDEO SW on remote control to change to OFF status. Or go to VIDEO SETUPPAGE to set the COMPONET as OFF.
SCART connection
- Use the 21pin Euro SCART cable to connect to DVD player and TV set, to get a better video and audiosignal together. In case of SCART connection, it is not necessary to connect DVD player and TV set with
RCA audio cable any more. The EURO CART cable has audio and video transferring capacity.
- Remember to press VIDEO SW on remote control to cahnge to RGB status. Or go to VIDEO SETUPPAGE to set the COMPONENT as RGB.
Component video connection
- Use the YUV cable (of three cables, in colors of RED, BLUE ,GREEN ) to connect DVD player with TVset or AV receiver, to get the best video signal output to TV or monitor. Connect the Green cable from Y
socket of DVD player, blue cable from Pb/Cb socket of DVD player, red cable from Pr/Cr socket of DVD
player, to the same color socket in TV set or AV receiver.
- Remember to press VIDEO SW on remote control to change to YUV status. Or go to VIDEO SETUPPAGE to set the COMPONET as YUV.
-
7/21/2019 Manual Xwave 5000 Eng
14/32
- 13 -
SYSTEM CONNECTIONS
POWER
Before putting the plug of power supply cable to the outlet, make sure that all connections are correct. When you
are sure that you are doing correctly, then put the plug carefully to the power supply socket.
Press the button POWER on the front panel of device. Then press the button POWER on the remote control.
The VFD of this player display LOADING, means working mode of the player.
When the device is connected with power, the short switching over voltage of electricity could cause interference
with other electronics connected to the same circuit. If this situation will happen, the device shall be connected to
the socket in another circuit.
-
7/21/2019 Manual Xwave 5000 Eng
15/32
-
7/21/2019 Manual Xwave 5000 Eng
16/32
- 15 -
GETTING STARTED
A. Press to stop playback (if any),then press SETUP .
B. Press repeatedly to select { Preference Page }.
C. Use keys to highlight one of the options below, then press ENTER.
Audio
Select the preferred audio language for DVD playback.
Subtitle
Select the preferred subtitle language for DVD playback.
Disc Menu
Select the preferred disc menu language for DVD playback.
D. Use keys to select a language and press ENTER to confirm.
E. Repeat steps C ~ D for other settings.
Helpful Hints:
During DVD playback, you can switch the audio and subtitle languages by pressing the AUDIO and
SUBTITLE buttons on the remote control. However, this does not change the default settings you have made
here.
For some DVDs, the subtitle/audio/menu language can only be changed via the DVD disc menu.
-
7/21/2019 Manual Xwave 5000 Eng
17/32
-
7/21/2019 Manual Xwave 5000 Eng
18/32
- 17 -
GETTING STARTED
Setting the in MPEG-4
Option MPEG-4 Subtitle setup is designed for users who watch films in Standard MPEG-4 (Divx/ XViD).
Those functions installed here used for display subtitle inscriptions effectively and properly .
A Press SETUPon the remote control.
B Press repeatedly to select { MPEG4Subtitle Setup Page }.
C Press to move the highlight, select your favor setting.
-
7/21/2019 Manual Xwave 5000 Eng
19/32
- 18 -
DISC OPERATIONS
Playable discs
Your DVD player will play:
Digital Versatile Discs (DVDs)
Video CDs (VCDs)
Super Video CDs (SVCDs)
DVD+Recordable (DVDR), DVD+Rewritable (DVDRW)
Audio Compact Discs (CDs)
MP3/ Windows Media Audio(WMA)
Picture CD (Kodak, JPEG)
DivX files on CD-R(W)/DVD+R(W):
DivX 3.11/4.0/5.0
Xvid
Region Codes for DVD discs
DVD discs and players are designed with regional restrictions. Before playing a disc, make sure the disc is for the
same region as your player. The regional code for this DVD system is indicated at the rear panel.
IMPORTANT!
If the inhibit icon ( or X) appears on the TV screen when a button is pressed, it means the function is not
available on the current disc or at the current time.
Do not put any objects other than discs on the disc tray. Doing so may cause the disc player to
malfunction.
Playing a disc
A Turn on the TV to the Video In channel for the DVD system (e.g. EXT, 0, AV).
You should see the DVD background LOGO screen on the TV.
B Press OPEN/CLOSE to open the disc tray and load a disc, then press the same button again to close the disc tray.
Make sure the disc label is facing up. For double-sided discs, load the side which you want to play facing up.
You can also hold down the STOP button on the remote control to open and close the disc tray.
C Playback will start automatically. See the following pages for more playback options and features.
Helpful Hint:
If you are having trouble playing a certain disc, remove the disc and try a different one. Improperly formatted
discs will not play on this DVD system.
-
7/21/2019 Manual Xwave 5000 Eng
20/32
- 19 -
DISC OPERATIONS
Basic playback controls
During playback, press to pause the playback. Press again to resume playback
Selecting another track/chapter , Press / or use the numeric keypad (0-9) to key in a track/chapter
number. If the repeat track mode is active, press again to replay the same track/ chapter. (DivX movie is not
workable with this NEXT and PREVIOUS function.)
Searching backward/forward Hold down .
While searching, press / repeatedly to decrease/increase the search speed. To resume normal playback,
press (or PLAY on the remote control). Stopping playback Press
Helpful Hint:
This is a power-saving feature, the system will automatically switch to Eco Power standby mode if you do not
press any buttons within 30 minutes after a disc has stopped playing. Please press POWERkey on remote to
resume it.
Selecting various repeat functions
While playing a disc, press REPEAT on the remote control repeatedly to choose a repeat play mode.
DVD
RPT ONE (repeat chapter)
RPT TT (repeat title)
SHUFFLE (random play)
RPT SHF (repeat random play)
RPT OFF (exit repeat mode)
VCD/SVCD/CD
RPT ONE (repeat track)
RPT ALL (repeat disc)
SHUFFLE (random play)
RPT SHF (repeat random play)
RPT OFF (exit repeat mode)
MP3/DivX/Windows Media Audio
RPT ONE (repeat track)
RPT ALL/FLD (repeat folder)
SHUFFLE (random play)
RPT OFF (exit repeat mode)
Helpful Hint:
Repeat playback is not possible on VCDs when the PBC mode is turned on.
-
7/21/2019 Manual Xwave 5000 Eng
21/32
- 20 -
DISC OPERATIONS
Other playback features for video discs (DVD/VCD/SVCD)
Using the Disc Menu
Depending on the disc format, a menu may appear on the TV screen once you load the disc.
To select a playback feature or item Use keys or numeric keypad (0-9) on the remote control, then
press ENTERto start playback.
To access or remove the menu, press TITLEor ROOTon the remote control.
TIPS: The operating features described here might not be possible for certain discs. Always refer to the
instructions supplied with the discs.
This DVD system can display the disc playback information (for example, title or chapter number, elapsed playing
time, audio/subtitle language) and a number of operations can be done without interrupting disc playback.
A During playback, press OSD, disc information appears on the TV.
B Use OSD keys to shift between different disc information.
-
7/21/2019 Manual Xwave 5000 Eng
22/32
- 21 -
DISC OPERATIONS
Zooming in
This option allows you to enlarge the picture on the TV screen and to pan through the enlarged picture.
A During playback, press ZOOMon the remote control repeatedly to select a different zoom factor. Use
keys to move through the zoomed image. Playback will continue.
B Press ZOOMrepeatedly to return to the original size.
Changing subtitle language (DVD only)
This operation works only on DVDs with multiple subtitle languages. You can change the language you want
while playing a DVD. Press SUBTITLErepeatedly to select different subtitle languages.
Changing sound track language
This operation works only on DVDs with multiple soundtrack languages, you can change the language you want
while playing a DVD. press AUDIOrepeatedly to select the available audio languages.
While playing a VCD, press AUDIO repeatedly to select the available audio channels provided by the disc
(STEREO, MONO LEFT, MONO RIGHT or MIX MONO).
Switching camera angles
This option is only available with DVDs that contain sequences recorded from different camera angles. This
allows you to view the picture from different angles. Press ANGLE repeatedly to select the available camera
angles.
Playback Control (VCD only)
Playback Control (PBC) playback allows you to play VCDs interactively, following the menu on the display.
When playback is stopped, press RETURN/TITLE to turn on or off the PBC mode. During playback, press
RETURN/TITLEto return to the disc title menu or main menu.
Play a MPEG-4 (DiVX / XViD) Disc
This unit reads following formats: MPEG-4 (DiVX / XViD).
A lot of MPEG4 format movie downloaded from internet, including QPEL, can be burned in a CD or DVD-R/RW,
and play in this player. If you need subtitle to be with the MPEG4 movie, you can burn the subtitle file, including
format as TXT (MicroDVD, TM Player, MPL2), SUB, SRT.SMI etc. Make sure the movie file and subtitle file are
named in the same. This unit is one of the most universal one in the market, for supporting mpeg4 movie format
and subtitle file formats.
When playing MPEG4 movie, enjoy our Subtitle Pro function, with access to MPEG4 SUBTITILE SETUP
PAGE.
-
7/21/2019 Manual Xwave 5000 Eng
23/32
- 22 -
DISC OPERATIONS
Play a MP3/WMA Disc
Mp3/WMA is the most popular standard in digital encrypting. Full their service along with the wide scale of tools
what offers our equipment - equalizers, filters, regulation of double bass and high sounds make you pleasant by
listening music. MP3 is technology of sound compaction, according to standard MPEG3. Pack file in ratio 12:1,
enable to play music more than 600 minutes.
Playing file Mp3
A. Operate conforming to the basic instruction. Load the disc with MP3 file. After the tray is closed,
device automatically search information in disc and display all MP3 or WMA files on the screen of TV.
B. Move the cursor to the files you want to play.
C. Press ENTERor PLAYto play the file.
Play a JPEG image file
The Joint Photographic Experts Group create standard for continuous tone image coding. At present this is
commonly used format for image compression and recording. Currently standard JPEG is used by majority
software for creating pictures and recommended for gathering pictures and photos.
A. The playback by means digit keys
When the disc tray is closed, device automatically search the information recorded on disc and display them
on TV.
Operate number keys select the right album with photos.
Notes:
Key numbers are functional only for current album with photos.
B. The playback by menu configuration
When the disc tray is closed, player automatically searches the information recorded on disc and display them
on TV. Operate number keys select the right photo and press PLAY or ENTER.
To select another picture, press STOP. Next press again directional key and choose picture you are interested in.
To confirm the choice press PLAYorENTER.
C. Other functions JPEG
During playback JPEG file, function such as pause, playback or replay is achievable.
To change the size of picture, press ZOOM. Press it again to unable this function.
Press again directional key during displaying pictures we could revise photos.
-
7/21/2019 Manual Xwave 5000 Eng
24/32
-
7/21/2019 Manual Xwave 5000 Eng
25/32
-
7/21/2019 Manual Xwave 5000 Eng
26/32
-
7/21/2019 Manual Xwave 5000 Eng
27/32
-
7/21/2019 Manual Xwave 5000 Eng
28/32
- 27 -
DVD Setup Menu Options
Password ModeEnable password for changing parental lock.
Optional Settings: On, Off.
Password Change the password. Default password: 136900
MPEG4 Subtitle Setup Page.
This unit has a super winning function of MPEG4 subtitle management function:
By using this function, you can do a lot of tricks and get a lot of fun when you enjoying your MPEG4 movie.
Subtitle FontChange the subtitle font, according to your TV size, or the length of the subtitle.
Option: Font 1 small size, Font 2 middle size, Font 3 big size.
Background
color
Change the Subtitle background color.
Option: 15 kinds of different colors for option
Outline ColorChange the outline color.
Option: 15 kinds of different colors for option
Text ColorChange the color of the subtitle text.
Option: 15 kinds of different colors for option
Horiz AlignChange the Horizontal display direction
Option: Left, center, right.
Vert AlignChange the Vertical display direction.
Option: From top, From bottom.
Reformat
Change the Reformat mode of subtitle.
ON: Display multiline subtitle, up to six lines.
OFF: display only one line.
-
7/21/2019 Manual Xwave 5000 Eng
29/32
- 28 -
SOFTWARE UPGRADES
Software upgrades
Periodically we will issue software upgrades to enhance your user experience or player performance.
To get a software and upgrade your system
A. Visit our website to check the availability of the latest software upgrade. Download the software to a CD-R.when burn the CD, Do remember name the CD as MEDIATEK, without any change of the BIN file name.
B. Press OPEN/CLOSE to open the disc tray.C. Insert the CD-R and press OPEN/CLOSE again. The software will start to install on the recorder
automatically.
IMPORTANT! Power supply must not be interrupted during upgrade! That will damage the unit surely!
D. after the upgrading is finished, the Disc tray will open automatically. Take the disc out
E. RESETthe machine and play as normal again.
-
7/21/2019 Manual Xwave 5000 Eng
30/32
- 29 -
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not
open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before
taking the system for repair. If you are unable to solve a problem by following these instructions, consult your
dealer for help.
Symptom Cause Solution
No sound Cables not properly connected.
Disc warped or dirty.
Player in mute status.
Connect cables securely.
Clean your disc.
Press MUTE button again.
No picture Cables not properly connected.Correct input not selected on TV.
Connect cables securely.Reset the AV/TV status of your TV set.
No color TV system not right.
TV set color not properly adjusted.
Press PAL/NTSC button.
Adjust color of the TV set.
No disc reading No disc in the player.
Disc not properly loaded.
Condensation on the laser head.
Load a disc
Reload a disc, with the label side facing up.
Turn on the player, unload the disc and leave it on
for about an hour.
Remote control
failure
Remote control not pointing to the
sensor window.
Remote controls operating distance is
more than 8 meters away from the TV.
Batteries is low.
Point the remote at the unit.
Use the remote control within 8 meters of the unit.
Replace the batteries.
Temporary
function failure
Badly fabricated disc used.
Wrong buttons pressed.
External electrical interference
Wait 5-10secs and the player will return to normal
operation once more.
Wait 1-3 seconds and press correct button Turn of
the player for 1-2 minutes, then switch back on.
If problem persists relocate the player or eliminate
source of interference.
Rolling Picture TV set not properly adjustedIncorrect output format on DVD unit
Readjust TV systemSelect correct output format for your TV
(PAL/NTSC)
-
7/21/2019 Manual Xwave 5000 Eng
31/32
- 30 -
Specifications
5.1CH DIGITAL MPEG4 PLAYERLAYER/OUTPUTS/SUPPLIED ACCESSOR
Power supply: AC100-220V 50/60 Hz
Power consumption: 20W
Power consumption in preparation mode: 5W
Mass: around 2.8 kg
External dimensions 430 x 280 x 38 mm
TV system: PAL 625/50, NTSC 525/60
Playable Format: DVD, MPEG-4 (DivX/XviD), MP-3, WMA, CD, JPEG, VCD, SVCD.
Ratio of signal and distortion (audio): more than 100dB
Speed range (audio): more than 95dB
Output
Video output: Composite video,S-video output, Y,Pb/Cb, Pr/Cr component video.
SCART output
Audio output: 5.1Channel audio, Coaxial , optical
ATTENTION:
The product will be modernized continuously, and firmware will be modified and available from our website for
user upgrade without notice.
Specification is subject to changes without any prior notice.
-
7/21/2019 Manual Xwave 5000 Eng
32/32