manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV...

17
Hardware Manual AZBox 2011 | english rev. 1.2

Transcript of manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV...

Page 1: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

Hardware Manual

AZBox 2011 | english rev. 1.2

Page 2: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

2

AZBox Me | Hardware Manual | 2011 rev. 1.2

NOTEThank you for choosing AZBox. You will be surprised by the features of one of the most innovative

product in the world of set top boxes: AZBox Me. Before using the product, please read carefully all the useful information provided in this manual.

It will help you take full advantage of the features of AZBox Me and will alert you to necessary safety precautions preceding its fi rst usage.

Please note that we are not liable for any losses or damage of personal data, resulting from any inappropriate use of the products. Additionally, we shall not be responsible for any eventual misunderstanding regarding the content of this manual as well as any other situation arising from the wrong usage of this product.

The information provided in this manual is confi dential and copyrighted. As such, it shall not be reproduced, altered, or distributed without the written consent of the company, OpenSAT, Lda. (www.azbox.com).

Page 3: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

3

AZBox Me | Hardware Manual | 2011 rev. 1.2

Table of ContentsNOTE 2Abbreviations 4Important Safety Information 4Danger 4Caution 5Environmental responsibility 6Additional Remarks 6

1. Package Contents 72. Product Overview 8

2.1. AZBox Me Features 92.2. The front panel 102.3. The rear panel 102.4. The side panel 112.5. The RCU (Remote Control Unit) 11

3. Installation 123.1. The RCU 12

3.1.1. Installing baterries in RCU 123.1.2. Using TV button 12

3.2. AZBox Me Connections 123.2.1. Connections to antenna 123.2.2. Connections to TV 13

I. HDMI connector 13II. Component video connector 13III. Composite video connector 13

3.2.3. Audio connection 143.2.4. Internet connection 14

3.3. Internal HDD installation 143.4. Powering on for the fi rst time 15

4. Troubleshooting 155. Identify Your Set-Top-Box 156. Technical Specifi cations 167. Contact and support information 17

Page 4: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

4

AZBox Me | Hardware Manual | 2011 rev. 1.2

AbbreviationsAV Audio/VideoEPG Electronic Program GuideHDMI High Defi nition Multimedia InterfaceDVB Digital Video BroadcastingDVB-S Digital Video Broadcasting- SatelliteDVB-T Digital Video Broadcasting - TerrestrialLAN Local Area Network OSD On Screen DisplayPPV Pay Per View RCU Remote Control UnitSTB Set Top Box

Important Safety InformationBefore installation, please read carefully the important remarks below, in order to operate the receiver safely and properly.

O Always follow the instructions below to avoid the risk of injury to yourself or damage to your equipment.

O If you do not intend to use this unlit for a long time, please pull the power plug out from the outlet. Do not use a damaged power cord.

O Do not expose the unit to water or any liquid. In such a situation, turn off the power and on again after 1-2 hours.

O Unplug the receiver from the AC power outlet before cleaning. Use only a damp cloth for cleaning the exterior of the receiver.

O Install the dish with correct direction and angle. If the dish is not working properly, please contact your local dealer

O Install the unit horizontally. Unbalanced installation may damage unit. O Moving the unit suddenly from a hot to a cold area may cause damage. O Operate the receiver in a ventilated area, one with suitable temperature, no direct sun rays, low

humidity and low vibration infl uence O Do not put heavy objects on top of the unit. O Do not use accessories or attachments not recommended by the manufacturer or authorized

representative, as they may cause hazards and will void the warranty.

DangerDANGER indicates an immediate hazardous situation which, if not avoided, will result in death or serious injury.

O Never open the cover. It is very dangerous to touch the inner part of the unit, as it might result in electric shock.

O Do not attempt to modify this receiver in any way. To do so may result in fi re, injury, electronic shock or severe damage to you or your receiver. Internal inspection, maintenance and repairs should only be carried out by your dealer or OpenSAT.

O Please do not use this receiver in close proximity to fl ammable, chemical water or explosive gases, as this could increase the risk of explosion.

O Make sure to turn off power switch and pull out power plug when moving product and do not forcefully pull out power cord.

Page 5: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

5

AZBox Me | Hardware Manual | 2011 rev. 1.2

CautionA. Do not place the receiver on an unstable cart, stand, tripod,

bracket, or table. The receiver may fall, causing serious personal injury and damage to the receiver.

B. The power supply should be near the equipment. Do not run an extension lead to the unit.

C. Protect the power cord from being walked on or pinched. If the cord is damaged, do not use the digital receiver and get the cord replaced.

D. Do not block or cover slots and openings in the receiver. These are provided for ventilation and protection from overheating. Never place the receiver near or over a radiator or heat register. Do not place the receiver in an enclosure such as a cabinet without proper ventilation.

E. Do not stack the receiver on top of or below other electronic devices. F. Operate the receiver using only the type of power source indicated on the marking label. Unplug the

receiver power cord by gripping the power plug, not the cord.G. Route power supply cords so that they are not likely to be walked on or trodden or perforated

by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.

H. For added protection during a lightning storm, or when the receiver is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the lines between the receiver and the antenna. This will provide some protection against damage caused by lightning or power line surges.

I. Do not attempt to service the receiver yourself, as opening or removing covers may expose you to dangerous voltage, and will void the warranty. Contact your dealer or OpenSAT.

O In case of any form of liquid or a foreign object enter the receiver, do not use it. Power off the receiver, and then disconnect the power cord. You must contact your dealer or OpenSAT. Do not continue to use the receiver as this may cause a fi re or electric shock.

O Do not insert or drop metallic or infl ammable foreign objects into the receiver through ventilation holes or access points, e.g. smart card slot. This may cause fi re or electric shock.

O Keep product away from severe vibration or magnetic objects O Do not cover up or install it in places with poor ventilation, under direct sunlight or near objects that

generates heat. O Do not connect a number of power plugs at the same time, this may cause fi re. O To reduce the risk of electric shock don’t remove the ‘ cover (or back) and do not operate this

receiver with wet hands. Equipment service and maintenance should be performed only by trained personnel.

This symbol is intended to alert the user of the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of suffi cient magnitude to constitute a risk of electric shock to persons.

The exclamation mark, within an equilateral triangle. Is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.!

Page 6: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

6

AZBox Me | Hardware Manual | 2011 rev. 1.2

Environmental responsibility Tthe packaging of AZBox consists only of reusable materials. This symbol found both in the box and in the equipment indicates that the product should not be discarded with household waste.

Therefore, in case you want to dispose of your equipment, please put it in a recycling point, one specifi c for disposal of electrical and electronic equipment. In this way you are helping us protecting the environment.

Additional RemarksThis device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.

Page 7: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

7

AZBox Me | Hardware Manual | 2011 rev. 1.2

I. Package Contents

Please check below if you have received the following parts:1. AZBox Me device2. Remote control unit3. Sata Cable4. One power cord

1

23

4

5

6

7

1

2

3

4

5. One power adaptor6. Two batteries for the remote control (AAA 1.5V)7. Quick Start Guide

Note: Accessories may vary according to your local area.

5

6

7

Page 8: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

8

AZBox Me | Hardware Manual | 2011 rev. 1.2

The AZBox Me HD Digital receiver is built with the latest technology, fully compliant with the international Digital Video Broadcasting (DVB) standard, and thus is able to receive digital broadcasts of that standard.In addition, the new AZBox Me is a very powerful STB receiver which presents already known functions as you can see next page.The future is Me, the beginning of a new generation.

2. Product Overview

Page 9: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

9

AZBox Me | Hardware Manual | 2011 rev. 1.2

2.1. AZBox Me Features

EPGElectronic Program Guide on AZBox Me allows you to schedule the recording of programs for later viewing, or schedule a watching list that will change the channel automatically to your favorite programs. A new way to never lose your favorite show. TV will never be the same.

TV/Radio ReceptionAZBox Me presents high quality image and sound, for you to enjoy the reception and reproduction of television or radio contents. You can create personalized favorites` lists of channels for easier navigation. We also include several built-in lists automatically fi lled after a scan. AZBox Me gives you the ability to sort your channels by satellite, genre, provider, country...

Recording Time ShiftOn AZBox Me you will not lose any critical scene of your favorite show, in casef you need to leave the room. Just activate the Time Shift function, the reproduction is paused and later you can resume it from that exact moment onwards. You can also choose to record the show for later viewing, which can be done by pressing a button, or by scheduling the recording. With Me, you have time on your hands.

Media PlayerAZBox Me is also a Media Player with full functionality for media of our modern days. Music, photos and video are easily played and accessed with our models. Allowing you to play your favorite songs, watch your holiday photos and movies. You can also play many advanced and high quality formats of audio and video.

VFD DisplayChannel related information and system operations are displayed via the VFD on the front part of the receiver.

Support Conax encryption systemAZBox Me is equipped with a card reader (Conax license).

1080pAZBox Me is capable of reproducing the High Defi nition format 1080p. With this format you can enjoy the highest quality content in the comfort of your home. Watching TV will become a totally new experience with crystal clear image, as if it were happening in front of you.

DVB-API compatibleThe AZBox Me Receiver is DVB-API compatible.

File BrowserAZBox Me has a File Browser totally compatible with your local or remote fi les, so you are able to copy, cut and paste them. You are able to browse fi les, not only in the local drive but also in the external drives connected, by using its USB hosting feature. Additionally, you can experience high level of convenience with the possibility of using wire/wireless networks, for the connection with your PC.

MultibootAZBox Me give you the possibility of multiboot, that permit you to have 2 OS installed at the same time, which you can choose when you are booting.

Recovery Boot:This option give You a chance for safe recovery Your device if fl ashing procedure of software failed. If You can’t boot Your device, turn it off, place switch to the recovery and turn it on, receiver will automatically fl ash it self with all needed things so You can put Software again.

Page 10: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

10

AZBox Me | Hardware Manual | 2011 rev. 1.2

2.2. The front panelThe front panel of the AZBox Me has one button to perform powering on and off and a display to indicate its status. Follows below an indication of what they mean.

Power Button: To switch the receiver between Standby mode and Operating mode (Power-ON). To reboot the device, press this button for 3 seconds.

LED Indicator. LED around Power button shows two different colors as below.1. Blue LED: when the STB is on Power-on mode.2. Orange LED: when the STB is on Standby mode.

Main Display: Displays the following information:● TV mode: shows the channel name;● Standby mode: date and time;● Menu mode: current menu indications.

USB Slot: Connect to support devices (USB 2.0 Host - 5V, 500mA).(AZBOX Me model has 2 USB slots -1 on the rear, and other on the front panel)

2.3. The rear panelAZBox Me has a wide range of connections on its rear panel. Please verify the type of connections your television set has in parallel with the receiver. Follows below an indication of what they mean.

POWER SWITCH: To turn the digital receiver On and OFF.AC POWER INPUT: To connect AC power cord to deliver power to the digital receiver.Recovery / Normal BOOT: You can change “normal boot” to “recovery” position if fl ashing procedure of software failed.Optical S/PDIF: Dolby digital output socket for the audio system. Dolby Digital Optical Type.Composite VIDEO: Composite video output socket for television set (yellow).Component (Y/Pb/Pr) connector: Component video output socket for the television set (green/blue/red).Stereo AUDIO L/R: Stereo audio output socket for the television set or the audio system (white/red).E-SATA connector: To connect to external e-SATA storage devices.HDMI: Audio and video output socket for the high defi nition television set.USB Slot: To connect to support devices (USB 2.0 Host - 5V, 500mA).LAN: Local Area Network port.IF INPUT: Satellite broadcasting signal input socket.LOOP: An output that gives you the possibility of passing the satellite signal to other equipment.

AB

C

D

CA

B CD

HI

J

K

L MF

EG

AB

C

D

E

F

A

B

C

D

G

H

I

J

K

L

M

Page 11: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

11

AZBox Me | Hardware Manual | 2011 rev. 1.2

2.4. The side panelOn the right side panel, there is a Smart Card Slot that supports Pay Per View (PPV) TV using a Smart Card with Conax encryption.

2.5. The RCU (Remote Control Unit)

19 20 21

14 15

17 1816

11

11

12

9 101

2

3

4

5

6

7

13

8

1. TV Power > To turn TV on and off2. TV Mute > To mute the TV sound3. STB Power > To start/stop “standby” mode To turn AZBox on and off4. Numerique Buttons (0~9) > To input numbers/letters5. Home > To display main Menu6. Menu >To access to additional options7. Sub-T > To select a subtitle track8. Info > To show a description of the selected program9. Lang > To select a language track1 EPG > To display the EPG (Electronic Program Guide) of a program1 Navigation buttons > To move the cursor around menu screens1 OK > To determine your selection1 VOL +/- > To increase or decrease volume1 EXIT > To exit menus or to use as BACK function 1 TXT > To view teletext on TV screen (if available)1 CH ^/^ , to change the channels up and down1 COLOR Buttons > quick access to special options and to teletext pages 1 PREV /REW /FFWD / NEXT > Multimedia buttons1 REC > To Record 2 PLAY / PAUSE > To Pause and Play a program2 STOP > to STOP

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

Note:Some of the buttons presented, can be associated to different functions, depending on the software in use.

Page 12: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

12

AZBox Me | Hardware Manual | 2011 rev. 1.2

3. Installation

3.1 The Remote Control Unit3.1.1. Installing batteries in RCUTo Install batteries in the remote control, perform the following steps:A. Take off the battery cover from back of the remote control.B. Install two AAA batteries, following the instructions described in the

container and make sure the polarity (+/-) directions are correct.C. Put on the battery cover back.

Note:● Do not mix battery types (Alkaline and Manganese);● Do not short-circuit, heat, burn or disassemble batteries;● Used batteries must not to be disposed together with your household waste. Please, inquire about local regulations regarding disposal of used batteries.

3.1.2. Using TV buttonThe RCU has a TV button on the backside of the RCU, near the Battery cover, this is a 3 different position Switch button, and is ured for changing different customer code. Another Round button, can also be found, inside of Battery cover, nas is used to set up Learning Function for TV. End user can learn their original TV Power button to Azbox RC.

To use TV button on AZBox Me RCU with TV1, it’s necessary to:D. Press round Button for 3seconds until you see red LED is on.E. Press TV button on AZBOX and now you will see LED is blinking.F. Press Power button on Your original TV RC, and RC will send signal to AZBOX RC. When you see AZBOX RC led BLINK Three times. It means Learning is sucessful, or else please try again.

3.2. AZBox Me ConnectionsThere are several ways to set up the digital receiver.Set up the digital receiver suitably to your television and other appliances. If you have any problem with your setup or need help, please contact your dealer.

3.2.1 Connections to antennaWhatever sort of connection you have between the digital receiver and the television, you need to connect the digital receiver to your television antenna so that it can receive digital television services.Connect the antenna cable to the IF INPUT connector on the back panel of the receiver. Note: For the correct operation of this equipment you need an antenna, which must be installed separately.

TV button

Page 13: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

13

AZBox Me | Hardware Manual | 2011 rev. 1.2

3.2.2. Connections to TV Between all the following connectors of the receiver, we recommend you to use the fi rst one (HDMI) to get best picture quality.If your television does not have the matching connector, then use the next one in list, in the following order, for better picture quality:

I HDMI connector (HDMI)II. Component connector (YCbCr)III Composite connector (VIDEO) You should confi gure audio and video settings after connecting up the receiver.

I. HDMI connector

If you have a high defi nition television set, you should use a HDMI cable for best results. Plug one end of the cable into the HDMI socket on the digital receiver, and plug the other end into the matching socket on your television. In this case, you do not have to make audio connection because the HDMI connector can output stereo audio or Dolby digital audio.

II. Component video connector

You need to obtain a component video cable (RCA cable) to use the component video connector. Plug one ends of the cable into the Y (green), Pb (blue) and Pr (red) sockets on the digital receiver, and plug the other ends into the matching sockets on your television.

III. Composite video connector

You need to obtain a composite video cable (RCA cable) to use the composite video connector. Plug one end of the cable into the VIDEO (yellow) socket on the digital receiver, and plug the other end into the matching socket on your television.Note: You cannot view high defi nition (HD) video with this composite video connector.

Page 14: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

14

AZBox Me | Hardware Manual | 2011 rev. 1.2

3.2.3. Audio connectionYou need to obtain an audio cable (RCA cable) to connect the audio connectors. Plug one end of the cable into the AUDIO L(white) and AUDIO R(red) sockets on the digital receiver, and plug the other end into the matching sockets on your television or audio system.

To enjoy Dolby digital audio, your television or audio system must be able to decode Dolby digital audio, and you need to obtain a S/PDIF cable. Plug one end of the cable into the S/PDIF socket on the digital receiver, and plug the other end into the matching socket on your audio system.

3.2.4. Internet connection

To enjoy the power of Internet connection on your AZBox Me, you must have a network cable connected to the Internet and connect it in the LAN input on rear Panel. If you want to have a more comfortable wireless solution, you can use a wifi USB adapter.

3.3. Internal HDD installationEverything you need to install an HDD (2.5” or 3.5”) is with your AZBox Me. You will just need a screwdriver and your HDD.

1. Remove the screws.

2. Pull out the cover by sliding it back.

3. Attach the HDD to the slot with screws, connect the sata cable, the power cable and close the box.

Note: Please make sure that you removed all connections from your device and try to avoid direct contact with electronic parts.

Page 15: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

15

AZBox Me | Hardware Manual | 2011 rev. 1.2

3.4. Powering on for the fi rst timeNow that you have your digital receiver connected, you should plug it into a mains socket and turn on the Power Switch at the backside.

The front panel indicator will be lit blue.

- AZBox Me give you the possibility of multiboot, that permit you to have 2 OS installed at the same time, which you can choose when you are booting.

When you turn on the AZBox Me, you will fi nd useful menus on-screen that will give you access to many options and functions. The RCU will be your best friend helping you navigate through the features and selections. Please be aware that each software has its particular way of working and may change some features and attribute different functions to RCU buttons.

4. Troubleshooting

5. Identify Your Set-Top-Box

To fi nd the serial number for your AZBox, look on the back for a label that is similar to the example shown here.The serial number begins with “TD“.If your set-top requires troubleshooting in the future, your cable service provider may ask for this serial number.

Use the space provided here to record the serial number:

Problem What to doRemote control is not working Insert new batteries

Remove batteries and check polarityReboot your AZBox

AZBox does not respond Reboot your AZBoxNo reception on a channel Check position of dish

Scan channelNo video and audio Check wiring and connections

Realign dish

12dZXnCS/N : TDXXXX-XXX-XXXXXX

serial number

Page 16: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

16

AZBox Me | Hardware Manual | 2011 rev. 1.2

6. Technical Specifi cationsOperating System LinuxProcessor (CPU) SIGMA processor SMP 8655Working Memory DDR 256 MBVideo Memory DDR 256 MBTuner Single tuner (DVB-S2 or DVB-T/DVB-C) embedded.DiSEqC 1.0, 1.1, 1.2, USALSFlash Memory 512 MBHDD eSATA and internal SATAVideo Output PAL / NTSCVideo Containers MPEG1/2/4 (M1V, M2V, M4V); MPEG1/2 PS (M2P, MPG); MPEG2 Transport Stream (TS, TP, TRP, M2T, M2TS, MTS), VOB, AVI, ASF, WMV, IFO, ISO; Matroska (MKV), MOV (H.264), MP4, RMP4Video Codecs XVID SD/HD; MPEG-1; MPEG-2:MP@HL; MPEG-4.2: ASP@L5, 720p, 1-point GMC; WMV9: MP@HL; H.264: BP@L3; H.264: [email protected]; H.264: [email protected]; H.264: [email protected]; VC-1: MP@HL; VC-1: AP@L3Audio Containers AAC, M4A, MPEG audio (MP1, MP2, MP3, MPA), WAV, WMA, FLAC, OGGAudio Codecs AAC, AAC+, Dolby Digital, DTS, WMA, WMA Pro, MP1, MP2, MP3, LPCM, FLAC, Vorbis, DTS (Audio Passthrough); Dolby Digital (Audio Passthrough)

Picture Support JPEG, BMP, GIFSubtitle Supported SMI, SRT, TXT, SUB, SSAResolution 576i (480i), 576p, (480p), 720p, 1080i, 1080pEthernet 10/100 Base-T Ethernet (max.100Mbit/s)Front Panel 1x USB 2.0; Coloured Leds; VFD; Power Button;Rear Panel 1x HDMI; 1x Component (YcbCr); 1x RCA Video; 1x RCA Audio (L/R); 1x e-SATA1x RJ45; 1x USB 2.0; 1x Optical S/PDIF; Power Switch;Lateral Panel 1x CR Slot for PayTV (Conax License)Dimensions 250x240x45 (mm)

Operating System Processor (CPU) Working Memory Video Memory Tuner DiSEqC Flash Memory HDD Video Output Video Containers

Video Codecs

Audio Containers

Audio Codecs

LinuxSIGMA processor SMP 8655DDR 256 MBDDR 256 MBSingle tuner (DVB-S2 or DVB-T/DVB-C) embedded.1.0, 1.1, 1.2, USALS512 MBeSATA and internal SATAPAL / NTSCMPEG1/2/4 (M1V, M2V, M4V);MPEG1/2 PS (M2P, MPG); MPEG2 Transport Stream (TS, TP, TRP, M2T, M2TS, MTS),VOB, AVI, ASF, WMV, IFO, ISO;

XVID SD/HD; MPEG-1;

MPEG-4.2: ASP@L5, 720p, 1-point GMC;

H.264: BP@L3; H.264:

[email protected]; H.264: [email protected];

Matroska (MKV), MOV (H.264), MP4, RMP4

MPEG-2:MP@HL;

WMV9: MP@HL;

[email protected]; H.264:

AAC, M4A,

FLAC, OGG

MP1, MP2, MP3, LPCM, FLAC, Vorbis,

AAC, AAC+,

DTS (Audio Passthrough); Dolby Digital (Audio Passthrough)

WAV, WMA,

WMA, WMA Pro,

VC-1: MP@HL; VC-1: AP@L3

MPEG audio (MP1, MP2, MP3, MPA),

Dolby Digital, DTS,

Picture Support Subtitle Supported Resolution Ethernet Front Panel Rear Panel

Lateral Panel

JPEG, BMP, GIFSMI, SRT, TXT, SUB, SSA576i (480i), 576p, (480p), 720p, 1080i, 1080p10/100 Base-T Ethernet (max.100Mbit/s)1x USB 2.0; Coloured Leds;VFD; Power Button;1x HDMI;1x Component (YcbCr); 1x RCA Video; 1x RCA Audio (L/R); 1x e-SATA1x RJ45;

1x Optical S/PDIF;

1x CR Slot for PayTV (Conax License)

1x USB 2.0;

Power Switch;

250x240x45 (mm)Dimensions

Page 17: manual-me EN v1 - AzBox Americas · 4 AZBox Me | Hardware Manual | 2011 rev. 1.2 Abbreviations AV Audio/Video EPG Electronic Program Guide HDMI High Defi nition Multimedia Interface

17

AZBox Me | Hardware Manual | 2011 rev. 1.2

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

www.azbox.com | [email protected] | Tel: +351 251 656 134

7. Contact and support information O Headquarters and distribution:

Edifi cio OPENSAT, Lagoa S/N4950-283 Mazedo, MNÇPORTUGALTel: +351 251 656 134Fax: +351 251 652 966Info, sales and technical support: [email protected]

O Distribution Network:If you want to be our distributor please send us an email with some information about your company to: [email protected]

O RMA:As OpenSat , wants to be different from other producers and we always take very seriously our commitment to our users, we inform you that RMA is accessible and available from our Web site www.azbox.com. To go to the RMA form click here.

O Customer Support:If you have any questions about AzBox HD Products or need support let our engineers help you, or send us your suggestions through this link.

O Website:www.azbox.com

O Offi cial Forum:http://forum.azbox.com/

O Facebook:www.facebook.com/AZBoxHD

O Twitter:www.twitter.com/AZBOXHD