manual DVR
description
Transcript of manual DVR
GENESIS SR04
User Manual
R
CHAPTER 1
INTRODUCTION
1-1 CONTENTS ---------------------------------------------------- 1-2
1-2 INSTALLATION PRECAUTIONS ------------------------------ 1-3
1-3 PART NAME--------------------------------------------------- 1-6
1-4 SPECIFICATIONS ---------------------------------------------- 1-9
CONTENTS
1-1 CONTENTS `
GENESIS SR04
※ Contents are subject to change witho
POWER CABLE
ut notice.
1-2 INSTALLATION PRECAUTIONS
To ensure the product’s best performance, it is recommended to follow the instructions below.
.
VENTILATION
To prevent from overheating, ensure sufficient space and do not block ventilation..
SHOCK
Place the product in a place safe from outer shock.
.
HUMIDITY
Do not place the product in a humid area. The humidity can badly effect the product’s
operation.
TEMPERATURE
Avoid dust and do not place the product where temperature changes are extreme.
ELECTRIC NOISE
Do not place the product near a microwave, radio or TV. The frequency can generate
signal noise.
DIRECT RAY OF LIGHT
Direct ray of light can cause abnormal operation. Keep the product away from direct
sunlight.
VIBRATION
Install the product on an even surface and avoid vibration..
1-3 PART NAME
FRONT PANEL
① POWER SWITCH - Used to turn the product on/off, and when logging off.
② FRONT LED – The LED is Turned on when the power is on, when the HDD is in use and when
network is connected properly.
③ CHANNEL SELECTION and SPLIT – Used to select channel and for split screen view.
④ PLAYBACK BUTTONS – Used for operation in playback mode.
⑤ LIVE MODE – Used to change to live mode
⑥ SEARCH MODE – Used to change to search mode.
⑦ + , - BUTTONS – Used to control PTZ, zoom in/out of time bar and change configurations..
⑧ AUTO/OK , < > ︿ ﹀ BUTTONS – Used to control/change configuration.
⑨ CANCEL BUTTON – Used to cancel and exit.
⑩ MENU BUTTON – Used to enter menu mode.
⑪ USB – Keyboard, mouse and USB storage devices can be connected.
REAR PANEL
① USB ② LAN
③ VGA ④
VIDEO
INPUT ⑤
MULTIPL
EX
OUTPUT
⑥ SPOT
OUTPUT
⑦
AUDIO
INOUT
⑧
AUDIO
OUTPUT ⑨
SENSOR
INPUT
⑩ RELAY
OUTPUT
⑪ RS485 ⑫ RS232
⑬
POWER
REMOTE CONTROL
POWER BUTTON
MUTE BUTTON
ZOOM IN / CHANGE BUTTON
ZOOM OUT / CHANGE BUTTON
MENU BUTTON
CANCEL BUTTON
LIVE MODE BUTTON
SEARCH MODE BUTTON
CONFIGURATION CONTROL
BUTTON
PLAYBACK CONTROL
BUTTON
FULL SCREEN MODE BUTTON
SPLIT SCREEN MODE BUTTON
SWITCH SCREEN MODE BUTTON
BACKUP MENU BUTTON
1-4 SPECIFICATIONS
SPECIFICATIONS
Specifications SR04
Operating System Embedded Linux
Compression MPEG-4
Multiplexer Functionality Pentaplex(Live, Record, Playback, Backup and Network at the same time)
Recording Resolution D1, Half D1, CIF
Displaying Speed PAL 100fps, NTSC 120fps
Recording Speed PAL 100fps, NTSC 120fps
Video Input/Loop Output 4 / 0 BNC Composite
Video Output 2 BNC Composite (Spot, and Monitor),1 VGA
Audio Input/Output(RCA cable) 1 line/ 1 line
Sensor Input/Relay Output 4 line/ 1 line
Display Mode 1/4 and sequential, PIP
Backup Media USB storage(s), Network
Storage Media Max.2 Internal HDDs, 3 USB
Recording Mode Method Motion detection and Sensor
System Control Front Key, Mouse and Remote controller
Communication Port RS-232C, RS-485
Network LAN(Ethernet RJ-45, 10/100 base), DDNS, TCP-IP
Dimension SR04
Size(mm) 380(W)x308(D)x65(H)
Weight 4Kg(1 HDD built in)
Power AC100~240V 50/60Hz
Operating Temperature 0°C~40°C
Operating Humidity 10~80% RH
* Specification may change without any notice.
CHAPTER 2
SYSTEM APPLICATION
2-1 LIVE MODE............................................ 2-2 2-2 MENU MODE ......................................... 2-4 2-3 SYSTEM CONFIGURATION.................. 2-5 2-4 CAMERA CONFIGURATION............... 2-11 2-5 RECORD CONFIGURATION............... 2-17 2-6 EVENT CONFIGURATION .................. 2-19 2-7 NETWORK CONFIGURATION............ 2-23 2-8 SEARCH MODE................................... 2-28 2-9 SEARCH MENU................................... 2-29 2-10 SEARCH SETTINGS.......................... 2-30 2-11 BACKUP SETTINGS ......................... 2-33
SYSTEM APPLICATION
Menu may change for enhanced performance without notice.
1-5 LIVE MODE
The default setting for user is ‘admin’ with no password.
Click the button to activate GENESIS SR04
Use the buttons to change the user.
There are 5 total users – admin, anonymous, user1, user2, user3.
Time, date and camera number is displayed in live mode.
To activate the panel menu in live mode, click the right button of the mouse and press
the button.
- Changes the user or shuts down GENESIS SR04.
- Display menu mode.
- Display live mode.
- Display search mode.
- Full screen mode. Enlarges the chosen camera to full screen view.
- Split screen mode. Shows all four cameras in one screen.
- Channel switch mode. Full screen mode with the cameras switching.
- Rewind
- Play backward
- Stop
- Play
- Fast forward
- Go to last. Goes to the last saved frame.
1-6 MENU MODE
To activate menu mode, press the button on the front panel of GENESIS SR04 or click
the 의 button on the panel menu.
- System configuration icon.
- Camera setting icon.
- Record setting icon.
- Event setting icon.
- Network setting icon.
1-7 SYSTEM CONFIGURATION
- Display general information.
- Display product information.
- Set the date or time.
- Display storage information.
- Change password and user settings.
To activate general information, click the button in system configuration.
SYSTEM ID – Set the system ID number.
( System ID is used to synchronize the remote control )
To activate product information, click the button in system configuration.
MODEL – The model name of the product.
VERSION – The version of the product.
( Show in order of F/W VER – H/W VER – DATE )
MAC ADDRESS – The mac address of the product.
IP ADDRESS – The IP address of the product.
LANGUAGE – The language used in the product.
- Run firmware update.
To activate date&time settings, click the button in system configuration.
DATE – [ month / day / year ] Set the date.
TIME – [ hour : minute : second ] Set the time.
TIME SYNC – Synchronize the time.
TIME SERVER – The server to synchronize the time with.
To activate storage information, click the button in system configuration.
DEVICE NAME – The storage device name.
TYPE – The storage device type.
SIZE – The total HDD size.
TEMPERATURE – The current HDD temperature.
STATUS – The current overall HDD status.
To activate password settings, click the button in system configuration.
SELECTION – Select the user to change the password.
( admin / anonymous / user1 / user2 / user3 )
NEW – Enter new password.
CONFIRM – Enter new password again for confirmation.
Use the virtual numberpad to enter a new password. The numberpad is activated by
clicking the input cell.
1-8 CAMERA CONFIGURATION
- Display PTZ settings.
.
- Display channel settings.
- Display color settings.
- Display screen settings.
- Display monitoring settings.
To activate PTZ settings, click the button in camera configuration.
- Select the channel to change PTZ settings.
DEVICE NAME – Select the device name.
DEVICE ID – Set the device ID number.
FLOW CONTROL – Set the flow control settings.
( RTS/CTS // XON/XOFF // RTS/CTS + XON/XOFF )
BPS / PAR / BITS – Set the BPS, PAR, BITS of the device.
To activate channel settings click the button in camera configuration.
CHANNEL – The camera number to change settings.
NAME – Change the name of the channel.
( Use the virtual keyboard to change the channel name. The keyboard is
activated by pressing the button on the front panel of GENESIS SR04 .)
VIDEO – Set the video signal blocking settings.
( ON / OFF )
Audio – Change audio settings.
( ON / OFF )
!( GENESIS SR04 supports only 1 audio input )
To activate color settings, click the button in camera configuration.
CAMERA – Select the camera number to change the color settings.
BRIGHTNESS – Set the brightness of the camera.
CONTRAST – Set the contrast of the camera.
SATURATION – Set the saturation of the camera.
HUE – Set the hue of the camera .
- Changes all settings back to default values..
To activate screen settings, click the button in camera configuration.
TRANSPARENCY – Set the transparency of the OSD.
POSITION – Change the position of the screen using the buttons.
To activate monitoring settings, click the button in camera configuration.
OSD – Select whether to show the OSD or not.
( ON / OFF )
AUTO-SWITCHING – Set the interval in switch screen mode.
( 1 ~ 60 seconds )
SPOTOUT CHANNEL – Select the spot out channel.
( Channel 1/2/3/4 , server screen, auto switch screen )
OUTPUT – Select the output device.
( LCD OUT / TV OUT )
1-9 RECORD CCONFIGURATION
- Display recording settings
To activate recording settings, click the button in record configuration.
CHANNEL – The camera number to change settings.
RESOLUTION – Set the recording resolution.
( CIF / HalfD1 / D1 )
! ( All 4 channels change simultaneously )
FRAME – Set the recording frame rate.
( Each channel can be set individually )
EVENT FRAME – Set the event frame rate.
( Each channel can be set individually )
RECORDING QUALITY – Set the recording quality.
( VERY LOW – LOW – NORMAL – HIGH – VERY HIGH )
1-10 EVENT CONFIGURATION
- Display alarm settings.
- Display motion settings.
- Display video signal settings.
To activate alarm settings, click the button in event configuration.
SENSOR – The sensor number to change settings.
MODE – Set sensor settings.
( N.C / N.O / OFF )
ALARM – Set alarm settings.
( ON / OFF )
!( GENESIS SR04 supports only 1 alarm. )
ALERT – Set internal alert settings.
( ON / OFF )
To activate motion settings, click the button in event configuration.
CHANNEL – The channel number to change motion settings.
MODE – Set motion detection settings.
( ON / OFF )
ALARM – Set alarm settings.
( ON / OFF )
!( GENESIS SR04 supports only 1 alarm. )
ALERT – Set internal alert settings.
( ON / OFF )
MOTION SENSIBILITY – Set motion detection sensibility..
( VERY LOW – LOW – NORMAL – HIGH – VERY HIGH )
To activate video signal settings, click the button in event configuration .
CHANNEL – The channel number to change video signal settings.
MODE – Set video signal settings.
( ON / OFF , when turned OFF the ALARM and ALERT will not activate.)
ALARM – Set alarm settings.
( ON / OFF , only effective when mode is ON )
!( GENESIS SR04 supports only 1 alarm )
ALERT – Set internal alert settings.
( ON / OFF , only effective when mode is ON )
1-11 NETWORK CONFIGURATION
- Display TCP / IP settings.
- Display CMS(central management system) settings.
- Display E-MAIL settings.
- Display event filter settings.
To activate TCP / IP settings, click the button in network configuration.
CONFIGURATIONS – Set the IP type. ( STATIC IP / DHCP IP )
BANDWIDTH – Set the bandwidth.
( Dial-up(28.8/33/56)Kbps // ISDN(64)Kbps // ADSL/ISDN(96/128)Kbps //
ADSL(150/200/256/300/384/512)Kbps // DSL(1/2/5/10)Mbps //
LAN(1.5/100)Mbps // AUTO )
IP ADDRESS – Set the IP address *( Use virtual numberpad )
GATEWAY – Set the gateway address. *( Use virtual numberpad )
SUBNET MASK – Set the subnet mask address. *( Use virtual numberpad)
DNS – Set the DNS address. *( Use virtual numberpad) *
To activate CMS settings, click the button in network configuration.
CONFIGURATIONS – Select the CMS setting.
( ON / OFF )
( Events gone through filtering will be sent when CMS is ON )
SERVER IP ADDRESS – Set the server IP address.
*( Use the virtual numberpad )
PORT – Set the port number.
*( Use the virtual numberpad. )
* The virtual numberpad can be activated by clicking the
input cell.
To activate e-mail settings, click the button in network configuration.
CONFIGURATIONS – Set the e-mail mode.
( OFF / Not Authentication / Authentication )
( Not Authentication - SMTP authentication needed
/ Authentication - SMTP authentication unnecessary )
SMTP SERVER – Set the SMTP server address. *( Use virtual keyboard)
PORT – Set the SMPT server port number. **( Use the virtual numberpad)
ACCOUNT – Set the SMPT user account (Authentication mode) *( Use virtual keyboard)
PASSWORD – Set the SMPT user keyboard(Authentication mode) *( Use virtual keyboard)
SENDER – Set the mail address of e-mail sender. *( Use virtual keyboard)
RECEIVER – Set the mail address of e-mail receiver. *( Use virtual keyboard)
The virtual keyboard and numberpad can be activated by clicking the input cell.
* **
To activate event filter settings, click the button in network configuration.
LOGIN / LOGOUT – Select login/LOGOUT event filtering. ( ON / OFF )
SHUTDOWN – Select shutdown event filtering. ( ON / OFF )
SENSOR – Select sensor event filtering. ( ON / OFF )
MOTION – Select motion detection event filtering. ( ON / OFF )
VIDEO LOSS – Select video signal loss event filtering. ( ON / OFF )
DISK WARNING – Select HDD warning event filtering. ( ON / OFF )
SETTING CHANGE – Select setting change event filtering. ( ON / OFF )
1-12 SEARCH MODE
To activate search mode, press the button on the front panel of GENESIS SR04 or
click the button in the panel menu.
- Display the previous month.
- Display the next month.
- Zoom in to the data time bar.
- Zoom out of the data time bar.
- Shift time bar to the left.
- Shift time bar to the right.
1-13 SEARCH MENU
To activate search menu, exit search mode and press the button on the front panel of
GENESIS SR04 or click the button in panel menu.
( Search menu can not be activated in live mode. )
- Search settings icon.
- Backup settings icon.
1-14 SEARCH SETTINGS
- Activate log search.
- Activate event search.
To activate log search, click the button in search settings.
- Display the first page of searched log.
- Display the previous page of searched log.
- Display the next page of searched log.
- Display the last page of searched log.
To activate event search, click the button in search settings.
CAMERA – Select the camera to search events.
( CAMERA1 / CAMERA2 / CAMERA3 / CAMERA4 / CAMERA ALL )
DATE – Change the date to search events.
1-15 BACKUP SETTINGS
- Activate backup menu.
To activate backup menu, click the button in backup settings.
TARGET – Backup device information.
CAMERA – Select the camera to backup.
( CAMERA1 / CAMERA2 / CAMERA3 / CAMERA4 )
BACKUP TIME – Set the time section to backup.
RECORD TIME – Whole stored record time.
TARGET SIZE – The free space of the backup device.
DATA SIZE – The size of the backup file.
- Calculate the TARGET SIZE and DATA SIZE.
CHAPTER 3
WEB DVR
3-1 LOGIN---------------------------------------------------------- 3-2
3-2 LIVE MODE ---------------------------------------------------- 3-5
3-2 SEARCH MODE ------------------------------------------------ 3-5
1-1
Menu may change for enhanced performance without notice.
6 LOGIN
To connect to the GENESIS SR04 by internet, type in the IP address of the device in the
internet browser
Login by correctly entering the user name and password for the GENESIS SR04.
1-17 LIVE MODE
- Select display mode ( 1 – single camera display / 4 - split screen display ).
- Select the camera to display or manipulate.
- Zoom in, zoom out.
- Change the iris diaphragm.
- Set the focus.
- Advanced PTZ settings.
- PTZ control.
- Set the speed of PTZ control
- Check box to use audio.
- Click to take a snapshot of the live screen.
- Display search mode.
- Click to logout of WEB DVR.
1-18 SEARCH MODE
- Search calendar. Set the date to search recorded data.
- Playback control buttons.
( Rewind / Play backward / Pause / Play / Fast forward )
- Click to save data to PC.
- Display live mode.