manual de srvicio HCD-DX80.pdf

SERVICE MANUAL

MINI HI-FI COMPONENT SYSTEM

E Model

SPECIFICATIONS

HCD-DX80Ver 1.1 2001.11

9-929-593-12 Sony Corporation2001K0500-1 Home Audio Company

C 2001.11 Published by Sony Engineering Corporation

Model Name Using Similar Mechanism HCD-DX50

CD CD Mechanism Type CDM58E-30BD60

Section Base Unit Name BU-30BD60

Optical Pick-up Name A-MAX.3

Tape deck Model Name Using Similar Mechanism NEW

Section Tape Transport Mechanism Type TCM-230AWR41

– Continued on next page –

• HCD-DX80 is the tuner, deck, CD andamplifier section in MHC-DX80.

2

HCD-DX80

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.

This appliance is classified as a CLASS 1 LASER product. TheCLASS 1 LASER PRODUCT MARKING is located on the rearexterior.

Laser component in this product is capableof emitting radiation exceeding the limit forClass 1.

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous ra-diation exposure.

Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing• Keep the temperature of soldering iron around 270˚C

during repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering

or unsoldering.

NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electro-static break-down because of the potential difference generatedby the charged electrostatic load, etc. on clothing and the humanbody.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.

3

HCD-DX80

MODEL IDENTIFICATION— BACK PANEL —

MODELBR, E2, E51, SP, AR models

MX model

PARTS No.4-231-580-4s

4-231-580-5s

• AbbreviationAR : Argentina modelBR : Brazilian modelE2 : 120 V AC Area in E modelE51 : Chilean and Peruvian modelSP : Singapore modelMX : Mexican model

PARTS No.

TABLE OF CONTENTS

1. GENERAL ................................................................... 4

2. DISASSEMBLY ......................................................... 72-1. Disassembly Flow ........................................................... 72-2. Case (Top) ....................................................................... 82-3. Loading Panel .................................................................. 82-4. CD Mechanism Deck (CDM58E-30BD60) ................... 92-5. Front Panel Section ......................................................... 92-6. Tape Mechanism Deck (TCM-230AWR41) ................... 102-7. Back Panel Section .......................................................... 102-8. Main Board ...................................................................... 112-9. LEAF SW Board, HEAD (A) Board,

HEAD (B) Board ............................................................ 112-10. Base Unit (BU-30BD60) ................................................ 122-11. DRIVER Board, MOTOR Board, SENSOR Board ....... 12

3. TEST MODE ............................................................... 13

4. MECHANICAL ADJUSTMENTS ........................ 15

5. ELECTRICAL ADJUSTMENTS .......................... 15

6. DIAGRAMS6-1. Block Diagram –TUNER/CD Section – ......................... 216-2. Block Diagram –MAIN Section – .................................. 226-3. Note for Printed Wiring Boards and

Schematic Diagrams ....................................................... 236-4. Schematic Diagram –BD Board – .................................. 246-5. Printed Wiring Board –BD Board – ............................... 256-6. Schematic Diagram –MAIN Board (1/4) – .................... 266-7. Schematic Diagram –MAIN Board (2/4) – .................... 276-8. Schematic Diagram –MAIN(3/4)/HEAD Board – ......... 286-9. Schematic Diagram –MAIN Board (4/4) – .................... 296-10. Printed Wiring Board –MAIN Board – .......................... 306-11. Schematic Diagram

–POWER AMP/SENSOR Board – ................................. 326-12. Printed Wiring Boards

–POWER AMP/SENSOR Board – ................................. 336-13. Schematic Diagram

–PANEL/VIDEO SWITCH Board – .............................. 346-14. Printed Wiring Boards

–PANEL/VIDEO SWITCH Board – .............................. 356-15. Schematic Diagram

–CD SWITCH/PAD SWITCH Board – ......................... 366-16. Printed Wiring Boards

–CD SWITCH/PAD SWITCH Board – ......................... 376-17. Schematic Diagram –LEAF SW Board – ....................... 386-18. Printed Wiring Boards –LEAF SW/HEAD Board – ...... 396-19. Schematic Diagram

–ADDRESS SENSOR/DRIVER/MOTOR Board – ...... 406-20. Printed Wiring Boards

–ADDRESS SENSOR/DRIVER/5MOTOR Board – .... 416-21. Schematic Diagram

–MAIN TRANS/SUB TRANS Board – ........................ 426-22. Printed Wiring Boards

–MAIN TRANS/SUB TRANS Board – ......................... 436-23. IC Pin Function Description ........................................... 47

7. EXPLODED VIEWS7-1. Cabinet Section ............................................................... 527-2. Front Panel Section ......................................................... 537-3. Main Board Section ........................................................ 547-4. CD Mechanism Deck Section (CDM58E-30BD60) ...... 557-5. Base Unit Section (BU-30BD60) ................................... 567-6. Tape Mechanism Deck Section-1 (TCM-230AWR41) .... 577-7. Tape Mechanism Deck Section-2 (TCM-230AWR41) .... 58

8. ELECTRICAL PARTS LIST .................................. 59

4

HCD-DX80SECTION 1GENERAL

This section is extracted frominstruction manual.

5

HCD-DX80

6

HCD-DX80

7

HCD-DX80

• This set can be disassembled in the order shown below.

2-1. DISASSEMBLY FLOW

SECTION 2DISASSEMBLY

2-4. CD MECHANISM DECK(CDM58E-30BD60)(Page 9)

2-3. LOADING PANEL(Page 8)

2-2. CASE (TOP)(Page 8)

2-5. FRONT PANEL SECTION(Page 9)

2-7. BACK PANEL SECTION(Page 10)

2-8. MAIN BOARD(Page 11)

2-6. TAPE MECHANISM DECK(TCM-230AER41)(Page 10)

2-11. DRIVER BOARD,MOTOR BOARD,ADDRESS SENSOR BOARD(Page 12)

2-10. BASE UNIT (BU-30BD60)(Page 12)

2-9. LEAF SW BOARD, HEAD (A) BOARD,HEAD (B) BOARD(Page 11)

SET

8

HCD-DX80

Note: Follow the disassembly procedure in the numerical order given.

2-2. CASE (TOP)q;

q;

5 two screws (case 3 TP2)

7 two screws (+BVTP 3 × 10)


1 two screws (case 3 TP2)

6 screw (case 3TP2)

8 side panel (L)

4 side panel (R)

2 screw (case 3 TP2)

9 four screws (+BVTP 3 × 12)

qa case (Top)

2-3. LOADING PANEL

2 Pull-out the disc tray.

3 loading panel

1 Turn the pulley in the direction of the arrow.

Front panel side

CD mechanism deck (CDM58E-30BD60)

–BOTTOM VIEW–

9

HCD-DX80

9


7 screws (+BVTP 3 × 10)

8 Screws (+BVTP 3 × 10)

5 screw (+BVTP 3 × 10)

2 wire (flat type)(17 core) (CN304)

3 connector (CN1)

4 connector (CN2)

0 front panel section

1 connector (CN607)

2-4. CD MECHANISM DECK (CDM58E-30BD60)

2-5. FRONT PANEL SECTION

4 screw (+BVTP 3 × 10)


3 screw(+BVTP 3 × 10)

2 connector(CN202)

5 CD mechanism deck (CDM58E-30BD60)

10

HCD-DX80

2-6. TAPE MECHANISM DECK (TCM-230AWR41)

2 Tape mechanism deck (TCM-230AWR41)

1 five screws (+BVTP 2.6 × 8)

2-7. BACK PANEL SECTION

4 five screws (+BVTP 3 × 10)


1 connector (CN973)

2 connector (CN505)

6 back panel section

3 connector (CN891)

11

HCD-DX80

2-8. MAIN BOARD

2-9. LEAF SW BOARD, HEAD (A) BOARD, HEAD (B) BOARD


2 MAIN board

MAIN board

6 screw (+PTT 2 × 4)

4 screw (+PTT 2 × 4)

3 LEAF SW board2 five claws

5 head (A) board

7 head (B) board

1 Remove the four solderings.

12

HCD-DX80

2-10. BASE UNIT (BU-30BD60)

2-11. DRIVER BOARD, MOTOR BOARD, ADDRESS SENSOR BOARD

qa

9 two screws (+PTPWH M2.6)

1 screw (+PTPWH M2.6)

q; screws (DIA. 12)

7 two screws (+BVTP 2.6 × 8)

6 BD board

5 rivet

qs two insulators (BU-30)

2 holder assy

qs two insulators (BU-30)

8 two stoppers (BU)


qd base unit(BU-30BD60)


qa Pull-out the disc tray.

6 two screws (+BVTP 2.6 × 8)

qs screw (+PTPWH 2.6 × 8)

qd tray

1 screw (+BVTP 2.6 × 8)

qf screw (+BVTP 2.6 × 8)

7

0 MOTOR board

qg ADDRESS SENSOR board

4 driver board2

5 Remove the two solderings of motor.

9 connector



13

HCD-DX80SECTION 3TEST MODE

[Cold Reset]• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returningthe set to the customer.

Procedure:1. Press three buttons x , ENTER , and ?/1 simultaneously.2. The fluorescent indicator tube becomes blank instantaneously,

and the set is reset.

[Hot Reset]• This mode resets the set with the preset data kept stored in the

memory. The hot reset mode functions same as if the powercord is plugged in and out.

Procedure:1. Press three buttons x , ENTER , and DISPLAYsimultaneously.2. The fluorescent indicator tube becomes blank instantaneously,

and the set is reset.

[Tuner Step Change]• A step of AM channels can be changed over between 9 kHz and

10 kHz.Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “TUNER”, and press TUNER/BAND button

to select the BAND “AM”.3. Press ?/1 button to turn the set OFF.4. Press ENTER and ?/1 buttons simultaneously, and the display

of fluorescent indicator tube changes to “AM 9 k STEP” or“AM 10 k STEP”, and thus the channel step is changed over.

[Function Change Mode]• Select either VIDEO or MD of the external FUNCTION input.Procedure:1. Turn on the power.2. Hold down MD (VIDEO) button then press ?/1 button , and

release ?/1 button first in order not to switch off the setimmediately.The another function of the previous function is selected , theinput level is also changed and displayed “ MD ” or “VIDEO”.

[GC Test Mode]• This mode is used to check the software version, FL tube, LED,

keyboard and VACS.Procedure:1. Press three buttons x , ENTER , and DISC 2 simultaneously.2. LEDs and fluorescent indicator tube are all turned on.3. When you want to enter the software version display mode,

press DISC 1 . The model number and destination are displayed.4. Each time DISC 1 is pressed, the display changes starting

from MC version, GC version, CD version, CDD version, CDMversion, BD version, ST version, TC version, TA version andTM version in this order, and returns to the model number anddestination display.

5. When DISC 3 is pressed while the version numbers are beingdisplayed except model number and destination, year, monthand day of the software creation appear. When DISC 3 ispressed again, the display returns to the software version display.When DISC 1 is pressed while year, month and day of thesoftware creation are being displayed, the year, month and dayof creation of the software versions are displayed in the sameorder of version display.

6. Press DISC 2 button, and the key check mode is activated.

7. In the key check mode, the fluorescent indicator tube displays“K0 V0”. Each time a button is pressed, “KEY” value increases.However, once a button is pressed, it is no longer taken intoaccount.“VOL” value increases like 1, 2, 3 ... if rotating VOLUMEknob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in“–” direction.

8. Also when DISC 3 is pressed after lighting of all LEDs and FLtubes, value of VACS appears.

9. To exit from this mode, press three buttons in the same manneras step 1, or disconnect the power cord.

[MC Test Mode]• This mode is used to check operations of the respective sections

of Amplifier, Tuner, and Tape.

Procedure:* To enter MC Test Mode1. Press the ?/1 button to turn on the set.2. Press the three buttons of x , ENTER and DISC 3

simultaneously.3. The messages MUSIC, MOVIE, GAME and P FILE flash on

the FL display tube.The input FUNCTION is Changed to VIDEO.

* Check of Amplifier1. When v (CURSOR UP) button is pressed, GEQ increases to

its maximum and a message “GEQ MAX” appears.2. When V (CURSOR DOWN) button is pressed, GEQ decreases

to its minimum and a message “GEQ MIN” appears.3. When b (CURSOR LEFT) or B (CURSOR RIGHT) button

is pressed, GEQ is set to flat and a message “GEQ FLAT”appears.

4. When the VOLUME control knob is turned clockwise evenslightly, the sound volume increases to its maximum and amessage “VOLUME MAX” appears for two seconds, then thedisplay returns to the original display.

5. When the VOLUME control knob is turned counter-clockwiseeven slightly, the sound volume decreases to its minimum and amessage “VOLUME MIN” appears for two seconds, then thedisplay returns to the original display.

* Check of clock frequency1. To check the frequency of clock used to run the time in the unit,

the clock output is available at pin 39 (IC 501, MASTERCONTROL) only during MC test mode.

2. The frequency is 32.768 kHz or so.

* Tuner function1. In the test mode, the default-preset channel is called even when

the TUNER is selected and an attempt is made to call the presetchannel that has been stored in memory. (It means that thememory is cleared.)

2. The minimum, center and maximum frequency of each band isset then.

14

HCD-DX80

[CD Ship Mode (Memory Clear) ]• This mode moves the pickup to the position durable to vibra-

tion. Use this mode when returning the set to the customer afterrepair.

Procedure:1. Press ?/1 button to turn the set ON.2. Press three buttons x , ENTER and GAME simultaneously.3. After the "STANDBY" display blinks six times, a message

“LOCK” is displayed on the fluorescent indicator tube, and theCD ship mode is set.

[CD Ship Mode (No Memory Clear) ]• This mode moves the pickup to the position durable to vibra-

tion. Use this mode when returning the set to the customer afterrepair.

Procedure:1. Press ?/1 button to turn the set ON.2. Press CD button and ?/1 button simultaneously.3. After the "STANDBY" display blinks six times, a message

“LOCK” is displayed on the fluorescent indicator tube, and theCD ship mode is set.

* Tape function1. When a tape is inserted in Deck B and recording is started, the

input source function selects VIDEO automatically.When CD SYNC/HI-DUB button is pressed during Rec infunction, ALC is turned on.

2. When x button is pressed to stop recording, the Tape (Deck)B is selected and tape is rewound, tape is rewound using mbutton, tape is stops at around the record-starting position andplayback of the recorded portion of the tape is started. If PAUSEis inserted even once during recording, tape is rewound to theposition around the PAUSE position and is played back.

3. When CD SYNC / HI-DUB button is pressed during playbackof Deck B, either normal speed or high speed can be selectedby this button.

* AMS Test Mode1. Set TAPE function2. Select the desired loop by pressing the PLAY MODE button.

Insert a test tape AMS-110A or AMS-120 to Deck A.3. Press the SPECTRUM button to enter the AMS test mode.4. After a tape is rewound first, the FF AMS is checked, and the

mechanism is shut off after detecting the AMS signal twice.5. Then the REW AMS is checked and the mechanism is shut off

after detecting the AMS signal twice.6. When the check is complete, a message of either OK or NG

appears.

* To return to normal mode again.1. When you want to exit this mode, press the ?/1 button.2. The cold reset is enforced at the same time.

[VACS ON/OFF Mode]• This mode is used to switch ON and OFF the VACS (Variable

Attenuation Control System).

Procedure:Press the ENTER and SPECTRUM buttons simultaneously. Themessage “VACS OFF” or “VACS ON” appears.

[CD Service Mode]• This mode can run the CD sled motor freely. Use this mode, for

instance, when cleaning the pickup.Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “CD”.3. Press three buttons x , ENTER , and OPEN/CLOSE simul-

taneously.4. The CD service mode is selected.5. With the CD in stop status, press M button to move the pickup

to outside track, or press m button to inside track.6. To exit from this mode, perform as follows:

1) Move the pickup to the most inside track.2) Press ?/1 button to turn the set OFF.

Note: • Always move the pickup to most inside track when exiting fromthis mode. Otherwise, a disc will not be unloaded.

• Do not run the sled motor excessively, otherwise the gear can bechipped.

+

–

15

HCD-DX80SECTION 4

MECHANICAL ADJUSTMENTSSECTION 5

ELECTRICAL ADJUSTMENTS

0 dB=0.775 VDECK SECTION

1. Demagnetize the record/playback head with a headdemagnetizer.

2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to the

parts adjust.4. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.5. The adjustments should be performed in the order given in this

service manual. (As a general rule, playback circuit adjustmentshould be completed before performing recording circuitadjustment.)

6. The adjustments should be performed for both L-CH and R-CH.

7. Switches and controls should be set as follows unless otherwisespecified.

• Test Tape

Record/Playback Head Azimuth Adjustment

Tape Signal Used forP-4-A100 10 kHz, –10 dB Azimuth Adjustment

WS-48B 3 kHz, 0 dB Tape Speed Adjustment

P-4-L300J 315 Hz, 0 dB Level Adjustment

DECK A DECK B

Note: Perform this adjustments for both decksProcedure:1. Mode: Playback

Precaution1. Clean the following parts with a denatured alcohol-moistened

swab:record/playback heads pinch rollerserase head rubber beltscapstan idlers

2. Demagnetize the record/playback head with a headdemagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to the

parts adjusted.5. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

Torque Measurement

set

main boardCN301Pin 3 (L-CH)Pin 1 (R-CH)

main boardCN301Pin 2 (GND)

+–

level meter

test tapeP-4-A100(10 kHz, –10 dB)

3.06 N • m to 6.96 N • m31 to 71 g • cm

(0.43 – 0.98 oz • inch)

0.19 N • m to 0.58 N • m2 to 6 g • cm

(0.02 – 0.08 oz • inch)

3.06 N • m to 6.96 N • m31 to 71 g • cm

(0.43 – 0.98 oz • inch)

0.19 N • m to 0.58 N • m2 to 6 g • cm

(0.02 – 0.08 oz • inch)

6.96 N • m to 14.02 N • m71 to 143 g • cm

(0.98 – 1.99 oz • inch)

9.80 N • m100 g or more

(3.53 oz or more)

9.80 N • m100 g or more

(3.53 oz or more)

Mode Torque meter

CQ-102C

CQ-102C

CQ-102RC

CQ-102RC

CQ-201B

CQ-403A

CQ-403R

Meter reading

FWD

FWD

back tension

REV

REV

back tension

FF/REW

FWD tension

REV tension

16

HCD-DX80

2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screwso that outputs match within 1dB of peak.

3. Mode: Playback

4. After the adjustments, apply suitable locking compound to thepats adjusted.

Adjustment Location: Playback Head (Deck A).Record/Playback/Erase Head (Deck B).

Tape Speed Adjustment DECK BNote: Start the Tape Speed adjustment as below after setting to the test

mode.In the test mode, the tape speed is high during pressing the CD SYNC/HI-DUB button.

Procedure:1. Turn the power switch on.2. Press the x button, ENTER button and DISC 3 button

simultaneously.(The “TEST MODE” on the fluorescent indicator tube displaywhile in the test mode.)To exit from the test mode, press the ?/1 button.

Mode: Playback

1. Insert the WS-48B into the deck B.2. Press the gG button on the deck B.3. Press the CD SYNC/HI-DUB button in playback mode.

Then at HIGH speed mode.4. Adjust RV1001 on the LEAF SW board so that frequency

counter reads 6,000 ± 30 Hz.5. Press the CD SYNC/HI-DUB button.

Then back to NORMAL speed mode.6. Adjust RV1002 on the LEAF SW board so that frequency

counter reads 3,000 ± 15 Hz.Adjustment Location: LEAF SW board

Playback level Adjustment DECK A DECK BProcedure:Mode: Playback

1. Confirm that level difference between the channels is with ±0.5 dB.

2. After check, adjust the following RVs.Deck A is RV302 (L-CH), Deck B is RV303 (L-CH) so thatadjustment within adjustment level as follows.

Adjustment Level:CN301 PB level: 334.4 to 748.7 mV (–7.3 to –0.3 dB)

Adjustment Location: MAIN board

Sample Volue of Wow and Flutter: 0.3% or less W. RMS(WS-48B)

Screwposition

L-CHpeak

within1dB

Outputlevel

L-CHpeak

R-CHpeak

within1dB

Screwposition

R-CHpeak

MAINboardCN301set

test tapeP-4-A100(10 kHz, –10 dB)

pin 1

oscilloscope

L-CH

R-CH

V H

waveform of oscilloscope

in phase 45° 90° 135° 180°

good wrong

pin 2

pin 3

L

R

+–

set

test tapeWS-48B (3 kHz, 0 dB)

main boardCN301 (Pin 3 : L-CH)

(Pin 1 : R-CH)

frequency counter

+–

set

test tapeP-4-L300J(315 Hz, 0 dB)

main boardCN301 (Pin 3 : L-CH)

(Pin 1 : R-CH)

level meter

forward

reverse

17

HCD-DX80

4. Mode: Record

5. Mode: Playback

6. Confirm the play back signal recorded in step 3 becomesadjustable level as follows.If these levels are not adjustable level, adjust the RV301 (L-CH) and RV351 (R-CH) on the MAIN board to repeat steps 4and 5.

Adjustable level:CN301 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)Adjustment Location: MAIN board

[MAIN BOARD] (Component Side)

[LEAF SW BOARD] (Component Side)

REC Bias Adjustment DECK BProcedure:In the MC test mode, the “REC memory mode” is convenient forthis adjustment. In the “REC memory mode” , when the REC startsthe input signal FUNCTION is switched to VIDEO automatically.When the REC stops, the tape returns near to the recording startposition.

1. Press MD (VIDEO) button to select VIDEO. (This step is notnecessary if the above test mode has already been set.)

2. Insert a tape into deck B.3. After press REC PAUSE/START button, press REC PAUSE/

START button, then recording start.4. Mode: Record

5. Mode: Playback

6. Confirm the playback signal recorded in step 3 becomesadjustable level as follows.If these levels are not adjustable level, adjust the RV304 (L-CH) and RV354 (R-CH) on the MAIN board to repeat steps 4and 5.

Adjustable level: Playback output of 315 Hz to playback outputof 10 kHz: ±1.0 dB


REC Level Adjustment DECK BProcedure:In the MC test mode, the “REC memory mode” is convenient forthis adjustment. In the “REC memory mode” , when the REC startsthe input signal FUNCTION is switched to VIDEO automatically.When the REC stops, the tape returns near to the recording startposition.

1. Press MD (VIDEO) button to select VIDEO. (This step is notnecessary if the above test mode has already been set.)

2. Insert a tape into deck B.3. After press REC PAUSE/START button, press REC PAUSE/

START button, then recording start.

attenuator

set

MD/VIDEO (AUDIO) IN (J101)

1) 315 Hz2) 10 kHz

50 mV (–23.8 dB)

600 Ωblank tapeCN-123

AF OSC

+–

set

recordedportion

CN301 (Pin 3 : L-CH)(Pin 1 : R-CH)

level meter

set

MD/VIDEO (AUDIO) IN (J101) 315 Hz, 50 mV (–23.8 dB)

blank tapeCS-123600 Ω

attenuator

AF OSC

+–

set

recordedportion

CN301 (Pin 3 : L-CH)(Pin 1 : R-CH)

level meter

TAPE SPEED

RV1002 RV1001

(NORMAL) (HIGH)

CN1001

T11

RV11

CN301

RV301

RV302RV353RV303

RV351RV304 RV354

NO303

CN304

RV352

3 1

REC LEVEL (L)(B)

PB LEVEL (L)(A)

PB LEVEL (L)(B)

REC LEVEL (R)(B)

REC BIAS (R)(B)

REC BIAS (L)(B)

18

HCD-DX80

FM Tuned Level Adjustment

Procedure:1. Supply a 98 MHz signal at 28 dB from the ANTENNA terminal.2. Tune the set to 98 MHz.3. Adjust RV11 to the point (moment) when the TUNED indicator

will change from going off to going on.


Null Adjustment

Procedure:1. Supply a 98 MHz signal at 60 dB from the ANTENNA terminal.2. Tune the set to 98 MHz.3. Measure voltage between pin 22 and pin 3 of IC11. Adjust

T11 until the voltage becomes 0 V.


Adjustment Location

[MAIN BOARD] (Component Side)

FM RF SIGNAL GENERATOR

75 Ω coaxial

Carrier frequency : 98 MHzModulation : AUDIO 1 kHz, 75 kHz deviation (100%)Output level : 28 dB (at 75 Ω open)

FM ANTENNA terminal (TM1)

set

FM RF SIGNAL GENERATOR

75 Ω coaxial

Carrier frequency : 98 MHzModulation : AUDIO 1 kHz, 75 kHz deviation (100%)Output level : 60 dB (at 75 Ω open)

FM ANTENNA terminal (TM1)

set

CD SECTION

Note :1. CD Block is basically designed to operate without adjustment.

Therefore, check each item in order given.2. Use LUV-P01 (4-999-032-01) unless otherwise indicated.3. Use an oscilloscope with more than 10MΩ impedance.4. Clean the object lens by an applicator with neutral detergent

when the signal level is low than specified value with thefollowing checks.

S-Curve Check

Procedure :1. Connect an oscilloscope to TP (FEO).2. Connect between TP (FEI) and TP (DVC) ( 1.65 V) by lead

wire.3. Turn Power switch on.4. Load a disc (LUV-P01) and actuate the focus search. (In

consequence of open and close the disc tray, actuate the focussearch)

5. Confirm that the oscilloscope waveform (S-curve) issymmetrical between A and B. And confirm peak to peak levelwithin 2 ± 0.5 Vp-p.

6. After check, remove the lead wire connected in step 2.Note : • Try to measure several times to make sure than the ratio

of A : B or B : A is more than 10 : 7.• Take sweep time as long as possible and light up the

brightness to obtain best waveform.

RF Level Check

Procedure :1. Connect an oscilloscope CH1 to TP (RFDC) and CH2 to TP

(RFAC).2. Turn Power switch on.3. Load a disc (LUV-P01) and playback.4. Confirm that oscilloscope waveform is clear and check if RF

signal level is correct or not.

BD boardOscilloscope

TP(FEO)TP(DVC)

T11

RV11

CN301

RV301

RV302RV353RV303

RV351RV304 RV354

NO303

CN304

RV352

3 1

NULL

FM TUNED LEVEL

TUNER SECTION

symmetry

S-curve waveform

within 2 ±0.5Vp-p

A

B

TP(RFDC)TP(RFAC)

BD board oscilloscope

TP(DVC)

19

HCD-DX80

Note : Clear RF signal waveform means that the shape “ ◊ ” can be clearlydistinguished at the center of the waveform.

E-F Balance (1 Track jump) Check

Procedure :1. Connect an oscilloscope to TP (TEO) and TP (DVC).2. Turn Power switch on.3. Load a disc (LUV-P01) and playback the number nine track.4. Press the gG button. (Becomes the 1 track jump mode.)5. Confirm that the level B and A (DC voltage) on the oscilloscope

waveform.

6. Adjust RV101 on the BD board so that the center of waveformbecomes the same voltage of DVC. (i.e. A=0V)

Adjustment Location:

[BD BOARD] (Conductor Side)RF signal waveform

VOLT/DIV : 200mVTIME/DIV : 500ns

level : 0.65 ±0.15Vp-p (RFDC)1.1 ±0.4Vp-p (RFAC)

TP(TEO)TP(DVC)

BD boardoscilloscope

level=1.0 ±0.5Vp-p symmetry

A (DC voltage)

center ofwaveform

B

DVC

1 track jump waveform

TP (TEO)

TP(RFAC)

TP(FEI) TP

(RFDC)

TP (FEO)IC101

IC103

RV101

TP (DVC)

115

30

1

2021

40

60

8041

61

16

20

HCD-DX80

MEMO

HCD-DX80

2121

SECTION 6DIAGRAMS

6-1. BLOCK DIAGRAM – TUNER/CD Section –

A

B

IC202

: FM

: CD

• Signal Path

• R-CH is omitted due to same as L-CH.

: DIGITAL OUT

FM 75Ω

G

AM

TM1

ANT IN1 7IF OUT

8OSC OUT

5VT

FE1FM FRONT-END

+B(11.7V) A+12V

Q2

FM10

FM OSC16A IN19A OUT20PD

B+(+7.4V)

B+(+5V)

18

PLLIC51

7FM

15AM OSC

9VCO STOP

8IF REQ

6DO

4DI

5CL

3CE

XIN1

XOUT22

X514.5MHz

RF IFAMP

Q1CF1 CF2

DO

DI

CL

CE

2

1

11

9

3

10

7

8

RB41AM FRONT-END

2AM MIX OUT

AM/IF11AM OSC24VCO STOP12IF REQ MUTING10

AM RF IN21

AM OSC23

VCC

FM IF1

AM/FM IF AMP, MPXIC11

13L OUT

14R OUT

BUFFERQ11

LPF11

LPF

4AM IF INIFT11

R-CH

6TUNED

7

9

STEREO

D51ST MUTING21

ST CE22

ST CLK27

ST DOUT23

ST DIN25

STEREO2

TUNED3

MASTER CONTROLIC501(1/2)

DO

CL

CE

DI

DI

OPTICALPICK-UPBLOCK

(A-MAX.3)

+5V

LDDRIVE

Q101

RF AMPIC103

VCVC

VCC

PD1PD2

I5-10

I1-6

LD

LD GND

PD

GND

F-

SW

F+

T-

T+

27 12VFC25A6B7C8D9E10F11

LD1

PD2

IC102MOTOR/COIL DRIVE

CH1RO13

CH1FO14

CH2RO11

CH2FO12

CH3RO18

CH3FO17

MM102SLED

MOTOR

CH4RO16

CH4FO15

MM101

SPINDLEMOTOR

3CH1RI

2CH1FI

6CH2RI

5CH2FI

23CH3RI

24CH3FI

25CH4INS

20MUTING

MDP26

SFDR28

SRDR29

TRDR30

TFDR31

FRDR32

FFDR33

SSTP27

DIGITAL SIGNAL PROCESSORD/A CONVERTER

IC101

DIGITAL SERVO

60D OUT

RFAC51

28RFDCO

15RFAC

SW

16FE

18TE

19TE BAL

RFDC43

FE39

TE41SE40

72L OUT

OUT

IC201

75R OUT

5DATA

R-CH

L OUT

L-CH

7CLOK

6XLAT

2SQCK

9SCLK

20SCOR

1SQSO

66XTAI

67XTAO

3XRST

X10116.9344MHz

CD DATA35

CD CLK37

XLT42

SQ CLK33

SCOR19

SQ DATA32

XRST43

TBL ADDRESSSENSOR49T SENS

IC711

48BU UP/DOWN SW

46OPEN SW

47CLOSE SW

44LOAD IN

OPEN/CLOSES701

BU UP/DOWN

S711

45LOAD OUT

MOTORDRIVE

9

7

4

2

M

IC701

TURNMOTOR

M721

6

12IF IN

RV11

+B(+7.4V)

AFC22

BU PWM226

HOLD40

BU PWM324BU PWM128

29RFDCI

17FEI

+3.3VREG

Q102

DVDD+3.3V

8SENS

13 12 1 2

11 10 3 4

9 8 5 6 SENS34

DIGITALOPTICAL OPTICAL

CD DIGITAL OUT

E-FBALANCE

RV101

(Page 22)

(Page 22)

HCD-DX80

2222

6-2. BLOCK DIAGRAM – MAIN Section –

A

B

: FM

: CD

• Signal Path

• RCH is omitted due to same as L-CH.

: PB (DECK A)

: PB (DECK B)

: REC (DECK B)

• Abbreviation: Argentina model: Chilean and Peruvian model: Mexican model: Singapore model: 120V Area in E model: Bragilian model

E51AR

MXSPE2BR

RECBIAS

BIASTRAP

R-CH

R-CHR CH

BIASOSC

Q302,303

RV304

Q301

B+(TC+12V)

C332,L301

ERASEHEAD

REC/PBHEAD

PB EQAMPIC304

IC302REC/PB SWITCH

RECEQ

BIASSW

DOLBYB

NORM

CROM

RV301

40

1

2

3

4

48

46

A

B

70

120

PB

REC

DOL

PAS

PB

REC

36

33

32

38 39

43

BIAS

ON/

OFF

20

B NO

RM/C

ROM

/MET

AL

ALC

ON/O

FF

15

RM O

N/OF

F

22

NR O

N/OF

F

23

REC

/PB/

PASS

24

LM O

N/OF

F

25

MS

OUT

26

MD/VIDEO(AUDIO)

R-CH

L-CH

LOUT

L-CH

J101

L

R

R-CH

PBHEAD

DECK-B

DECK-A PB EQAMPIC303

RV302

SWITCHQ304,305

17

A120

/70

PB A

/B

16

NORM

/HIG

H

18

DECK PROCESSORIC301

INPUT SELECTG EQIC101

IN2A40

IN2C38

IN2D37

VSELA OUT234

IN2B39

24VOL OUT2

DATA21CLOCK22

R-CH

L IN

IC701

LINE MUTE

PROTECT

STK MUTE

DBFBSWITCH

Q503R-CH

DBFBCONT

Q101,102

6

57

IC102

MUTINGQ103

MUTINGCONT

Q504,505

POWERAMP

IC501

18

12

10

MUTINGQ581

MUTINGCONT

Q503,504

MUTINGQ862

MUTINGCONT

Q861

R-CH

R-CH

D841OVER LOADDETECTOR

Q551

OVER HEATDETECTOR

Q505,506+B(+30V)

PROTECTDETECTOR

Q821,822

PROTECTCONT

Q823D502

PROTECTSWITCH

Q828,829

RELAYDRIVE

Q824,825 RY801

J631PHONES

R CH

R CH

M961(FAN)

FANDRIVE

Q891,892

L

R

TM801

SPEAKER

90 B SHUT

89 A SHUT

57 B PLAY

56 A PLAY

91 B HALF

70 A HALF

67

PB A

/B

A TRIGDRIVE

CAP MOTORDRIVE

Q396,397

Q393,394

B TRIGDRIVE

Q391,392

CAP MOTORSPEED CONT

Q395

A TRIG51

B TRIG52

CAP

M H

/L

54

CAP

M C

ONT

55

B TRG M+

19

69

TC R

ELAY

IC501(2/2)MASTER CONTROL

66

EQ H

/N

68

ALC

65

BIAS

61

REC

MUT

ING

60

NR O

N/OF

F

59

R/PB

PAS

58

TC M

UTIN

G

53

AMS

IN

80

GEQ

DATA

81GE

QCLK

79

DBFB

ON/

OFF

DCBIAS

Q141

B+(TCA+6V) A+12V

82

LINE

MUT

ING

REAR

REL

AY

83

STK

MUT

ING

87

FRON

T RE

LAY

88

PROT

ECT

30

IIC D

ATA

10

XC IN

11

XC O

UT

15

X IN

13

X OU

T

32.768kHzX501

16MHzX502

BPF 0

BPF 5

P1

P39

FLOURESCENTINDICATOR TUBE

DISPLAY CONTROLIC601

F1 F2

D608, 609D612-618

11

FUCTIONKEY

60 I2C DATA

61 I2CCLOCK

VOL A80VOL B79

ROTARYENCODER

X6014MHz

FL601

IC602

ALL BAND73

HEADPHONE78

S768-781

55TUNER

57CD

54TAPE A/B

56MD/VIDEO

58GAME IN

LEDDRIVER

Q601-605

LEDDRIVER

Q751

52REC/PAUSEPAUSE REC/START

D751

VOLUMES751

LEDDRIVER53ENTER ENTER

D752Q752

17

12

SPEANABPF

6

5

4

3

KEY064

FUCTIONKEY KEY165

FUCTIONKEY KEY266

77 RESET

MICJ722

MICLEVEL

RV722

IC722IC722

29

IIC C

LK

41

M R

ESET

T910

S901

JW971

F971

(MX)

JW97

5 (MX)

(EXCEPT MX)

+5VREG

Q941

D543

-VG(-32.2V)

+VH

-VHD541

+VL

-VL

POWERAMP

(IC501)

D901-904

EVER +5.6V

F1

F2

D972-975

AC

AC OUTTO

SATLLITEAMPLIFIER(TA-DX80)

IN

RELAYDRIVE

Q971

IC971

T972

13

+5.6VREG 13

RY971

RY972

+12VREG 13

+9VREG 13

CD POWERSWITCH

+5VREG 13

IC911 Q911,912

IC951

IC921

IC961

CD D+5V(SW)

CD A+5V(SW)

TC D+5V

AUDIO +5V

A+12V

TC A+12V

MIC A+12V

ST A+12V

TC M+9V

CDM M+7V

LED +7V

D906-909B+(+13.9v)(RY801)

D952

D953

D511ST

BY R

ELAY

84

38CD POWER

AC C

UT100

Q575

T301

HP901

HRPE901

5 7

75

3

21

IC301

IC104

TH701

3

21 6

57

LIMITERQ721

D920-922

D577

S1003(A. HALF)

S1004(A. 120/70)

S1006(B. HALF)

S1001(A. PLAY)

S1002(B. PLAY)

REELDET

IC1001

REELDET

IC1002

A TRG M+

MOTORCONT

M901

MCAPSTANMOTOR

Q1001

RV1002

S1005(REC. A)

S1009(REC. B)

(DECK-A)

(DECK-B)

R-CH

J401

VIDEO OUT

VIDEO

AUDIO L

R

J601

2

31

IC106

13

109

AB

12

11

IC105

Q104

FAN ONSWITCH

Q831

7167

72.

S753-758S760-765

S601-606S791-795

48VKK -VG

D791-79359DISC1

74DISC2

75DISC3

LEDDRIVER

Q791-793

5

1

100

93

.G1

G13

12

22

24

41

43

6

10

47

XIN83

XOUT82

.

.

.

78

GAM

E/VI

DEO

LEDDRIVER

Q794

SIRC

S

4

SIRCSIC603

BOOS

TER

SW

97

FREQ

B

94

FREQ

A

95

POW

ER K

EY

74

STBY

LED

75

?/1

S796DISPLAY

S752

?/1

D794

RESE

T12

RESET 13

IC502

STBY +5V

D508

VREF (IC501)

D +5V

D509

D510

D580D579VCC (IC501)

D977

D911 D910

D824 D822

JW973

JW972

JW986

(MX)

JW99

0

120

230-240

220

220

120

230-240

(EXCEPT MX)

IC616

+3.3VREG 13 +3.3V+3.3V

VOLTAGE SELECTOR

INPUT SELECTPM

901

PM90

2

GAMEINPUT

PBLEVEL (A)

RV303

PBLEVEL (B)

RECLEVEL (L)

A B

+–

NORM SPEED

RV1001

HIGH SPEED

S1008(A. 120/70)

INVOL OUT235

1 3

85

Q831, 832

RELAYDRIVE

RELAYON/OFF

(TA-DX80)SATELLITEAMPLIFIER(TA-DX80)

TOSATELLITEAMPLIFIER(TA-DX80)

CONT A

CONT BBOOSTER SW

STANDBY LED

IMPEDANCEUSE 6~16Ω

R-CH

-VREG

(Page 21)

(Page 21)

HCD-DX80

2323

6-3. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)

Note on Printed Wiring Boards:• X : parts extracted from the component side.• : Pattern from the side which enables seeing.• indication of transistor.

C

B

These are omitted.

E

Q

B

These are omitted.

C E

Q

Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• C : panel designation.

• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

F : FMf : AME : PB (DECK A)d : PB (DECK B)G : REC (DECK B)J : CDc : digital out

• AbbreviationAR : Argentina modelBR : Brazilian modelE2 : 120 V AC Area in E modelE51 : Chilean and Peruvian modelMX : Mexican modelSP : Singapore model

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

MOTOR board

ADDRESS SENSOR board

DRIVER board

MAIN TRANS board

VIDEO SWITCH board

SENSOR board

BD board

SUB TRANS board

MAIN board

POWER AMPLIFIER boardLEAF SW board

HEAD (A) board

HEAD (B) board

PANEL board

CD-SWITCH board

PAD SWITCH board

• Circuit Boards Location

2424

HCD-DX80

6-4. SCHEMATIC DIAGRAM – BD Board – • See page 31 for Waveforms • See page 44 for IC Block Diagrams.

IC B/D

IC B/D

IC B/D

(Page 27)

2525

HCD-DX80

6-5. PRINTED WIRING BOARD – BD Board – • See page 23 for Circuit Boards Location.

There are a few cases that the part printed onthis diagram isn’t mounted in this model.

Ref. No. Location

D101 B-3

IC101 C-3IC102 B-2IC103 D-2

Q101 C-1Q102 A-3

• SemiconductorLocation(Page 30)

2626

HCD-DX80

6-6. SCHEMATIC DIAGRAM – MAIN Board (1/4) – • See page 31 for Wavefoms. • See page 44 for IC Block Diagram.

(Page 27)

• Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.

• no mark : FM( ) : AM

2727

HCD-DX806-7. SCHEMATIC DIAGRAM – MAIN Board (2/4) –

(Page 24)

(Page 40)

(Page 28)

(Page 26)

(Page 29)

• Voltages are dc with respect to ground under no-signal(detuned) conditions.no mark : FM( ) : TAPE[ ] : CD

2828

HCD-DX806-8. SCHEMATIC DIAGRAM – MAIN (3/4)/HEAD Board – • See page 31 for Waveform. • See page 44 for IC Block Diagrams. • See page 39 for Printed Wiring Board of Head Boards.

• Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.no mark : FM( ) : TAPE[ ] : CD

The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.

(Page 27)

(Page 29)

2929

HCD-DX806-9. SCHEMATIC DIAGRAM – MAIN Board (4/4) – • See page 31 for Waveforms. • See page 47 for IC Pin Function Description.

(Page 28)

(Page 27)

(Page 38)(Page 34)

(Page 32) (Page 32)

• Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.no mark : FM( ) : TAPE[ ] : CD

3030

HCD-DX80

6-10. PRINTED WIRING BOARD – MAIN Board – • See page 23 for Circuit Boards Location.


MAIN BOARD

EPANEL BOARD

CN601

FLEAF SW BOARD

CN1001

(FOR CHECK)

31

50

51

80 81

100

30

1

E E

E E E

E

EE

3 1OHEAD (A) BOARD

CN1

PHEAD (B) BOARD

CN2

8 1

3 12

3 12

1

9

1 3

2

E

E

E E

6

4

1

3

E

1 32

EE

SE

E

S

1 32

1 3(FOR ADJUSTMENT)

E

E

E E

E

13 1 13 1

3 13 13 1

GPOWER AMPLIFIER BOARD

CN503

HPOWER AMPLIFIER BOARD

CN502

22

21

42

1

E

3 1E

EB

E

E

12

3

E

E

E

E

E

E

E E

E

E

E

E

E

E

14

85

1

13

2

12

1 2

3

1

2

3

4

FE1FM FRONT-END

1

2

3

E

ADRIVER BOARDCN701 B BD BOARD

CN101

OPTICALCD DIGITAL OUT

SYSTEMCONTROL

FM 75Ω

COAXIAL

ANTENNA

AM

R

L

CN101

MD/VIDEO(AUDIO)

J101

TO SATELLITE AMPLIFIER(TA-DX80)

+

+

–

–

TM1

IN

L

R

L

R

SPEAKER

RB41AM FRONT-END

M M961(FAN)

TM801

IMPEDANCEUSE 6~16Ω

1 32

(CHASSIS)

–1

–2

1-680-268-

11

(11)

(EXCEPT SP)

A

B

C

D

E

F

G

H

I

J

K

1 2 3 4 5 6 7 8 9 10 11 12 13 14

(Page 35)

(Page 39)

(Page 39)

(Page 39)

(Page 33) (Page 33)

(Page 41) (Page 25) Ref. No. Location

• Semiconductor LocationRef. No. Location

D51 A-12D508 D-2D509 D-4D510 E-4D511 D-2D575 E-4D576 E-4D577 E-4D578 E-4D579 E-4D580 D-4D801 I-12D822 G-11D824 G-11D841 I-12D861 I-9D892 H-13D893 H-13D901 I-10D902 I-10D903 I-10D904 I-10D906 I-10D907 I-10D908 I-10D909 I-11D910 J-7D911 J-7D912 G-10D920 I-7D921 I-7D922 I-8D952 H-7D953 H-7

IC11 D-12IC51 B-11IC101 E-8IC102 D-6IC104 C-7IC105 E-10IC106 D-9IC201 B-13IC202 B-10IC301 G-6IC302 H-5IC303 F-4IC304 H-4IC501 C-3IC502 E-4

IC701 F-12IC911 C-9IC921 H-9IC951 H-7IC961 H-8

Q1 C-11Q2 A-12Q11 D-11Q12 D-11Q101 D-7Q102 D-6Q103 I-8Q104 E-9Q141 E-5Q151 D-7Q152 D-7Q153 I-8Q301 I-5Q302 I-5Q303 I-5Q304 I-5Q305 I-6Q391 E-2Q392 E-2Q393 E-3Q394 E-2Q395 E-3Q396 E-3Q397 E-2Q503 E-6Q504 F-8Q505 G-8Q575 E-4Q821 G-12Q822 G-12Q823 G-12Q824 I-12Q825 H-12Q828 G-11Q829 G-11Q831 H-12Q832 H-12Q861 I-9Q862 I-11Q863 H-11Q891 G-12Q892 H-13Q911 C-9Q912 C-10

HCD-DX80

3131

• Waveforms– BD Board –

1 IC101 ta (RFAC) (CD Play mode) 6 IC601 is (X OUT) (Stop mode)

1.1 Vp-p

– PANEL Board –

3.5 Vp-p

4 MHz

– MAIN Board –

2 IC501 qa (XC OUT) (Stop mode)

3.1 Vp-p

32.768 kHz

2 IC101 ra (TE) (CD Play mode)

Approx.0.4 Vp-p

3 IC501 qd (X OUT) (Stop mode)

3.8 Vp-p

16 MHz

3 IC101 el (FE) (CD Play mode)

Approx.0.3 Vp-p

1 IC51 ws TUNER (FM)

4.3 Vp-p

4.5 MHz

4 T301 4 (DECK-B REC mode)

128 Vp-p

80 kHz

5 NO303 3 (L-REC), 6 (R-REC)(DECK-B REC mode)

52 Vp-p

80 kHz

4 IC101 wh (MDP)

2.5 Vp-p

7.5 µs

MEMO

3232

HCD-DX80

6-11. SCHEMATIC DIAGRAM – POWER AMP/SENSOR Board –

(Page 29)

(Page 42)

(Page 29)

(Page 42)


• Voltages are dc with respect to ground under no-signal(detuned) conditions.no mark : FM

3333

HCD-DX80

6-12. PRINTED WIRING BOARDS – POWER AMP/SENSOR Board – • See page 23 for Circuit Boards Location.


D501 B-2D502 C-2D503 C-6D504 C-6D541 F-3D543 F-5D551 B-2D581 C-5D941 F-3

IC501 A-5

Q501 C-2Q503 F-6Q504 G-6Q505 C-6Q506 C-7Q551 B-2Q581 C-5Q831 C-7Q941 E-3

• SemiconductorLocationRef. No. LocationPOWER AMPLIFIER BOARD

SENSOR BOARD

E

E

1

13

1

13

HMAIN BOARD

CN901

GMAIN BOARD

CN902

1

3

MSUB TRANS BOARD

NO976

LMAIN TRANS BOARD

CN977

1 2 13

E–

– ~ ~ +

+

~

~

E

E

E

EE

E

(CHASSIS)

(CHASSIS)

1-680-267-

11

(11)

1 2

1-681-143-

11

(11)

CN701

A

B

C

D

E

F

G

1 2 3 4 5 6 7 8

(Page 30)

(Page 30)

(Page 43) (Page 43)

3434

HCD-DX80

6-13. SCHEMATIC DIAGRAM – PANEL/VIDEO SWITCH Board – • See page 31 for Waveform. • See page 47 for IC Pin Function Description. • See page 44 for IC Block Diagram.

• Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.no mark : FM

(Page 36)

(Page 36)

(Page 29)

3535

HCD-DX80

6-14. PRINTED WIRING BOARDS – PANEL/VIDEO SWITCH Board – • See page 23 for Circuit Boards Location.


Ref. No. Location

D608 A-10D609 B-2D610 B-3D611 D-6D612 B-2D613 A-2D614 A-2D615 B-2D616 B-2D617 C-2D618 C-2

IC601 B-6IC602 F-3IC603 B-3IC616 C-3IC722 G-9

Q601 B-2Q602 A-2Q603 B-2Q604 C-2Q605 A-10Q721 E-8

• SemiconductorLocation

PANEL BOARD

CD

D613, 614S603

TUNER/BAND

D609, 612S604

MD (VIDEO)

D617, 618S601

MAIN BOARDCN401

TAPE A/B

D615, 616S602

E

30

29

12

1

2

43 7

6PHONES

J631

9

10

1

18

E

E

E

E

1 3

3 2 1

8 1

(FOR CHECK)

9 1

JPAD SWITCH BOARD

NO605

S601 – 606

51 10 15 20 25 30 35 40 45 50 55 60 66 70

1

30

31

50 51

80

81

100

FLUORESCENT INDICATOR TUBE

1 9

K

CD-SW BOARDNO603

E

14

85

E

GAME

VIDEO

AUDIO

GAME INPUTL

R

D608, S605

MIC

(EXCEPT BR)

J722

J601

MICLEVEL

RV722

SURROUNDSPEAKER MODE

S606

6

5

4 37

2

1

1-680-261-

11

(11)

12

3

D620 D619

1

1-680-892-

11

(11)

VIDEO OUT

J401

VIDEO SWITCH BOARD

2 1

(CHASSIS)

A

B

C

D

E

F

G

H

1 2 3 4 5 6 7 8 9 10 11

(Page 37)

(Page 30)

(Page 37)

3636

HCD-DX806-15. SCHEMATIC DIAGRAM – CD SWITCH/PAD SWITCH Board –

(Page 34)

(Page 34)


3737

HCD-DX80

PAD SWITCH BOARD

VOLUME

S751ROTARY ENCODER

9 1

JPANEL BOARD

NO604

S752 – 758,S760 – 765,S768 – 781

E

E

PLAY MODE

MOVIE EQ

SURROUND GROOVE

ENTER

ENTER

G

>.

X g G x

g

f

F

EDIT

SPECTRUM

DISPLAY

MUSIC EQ

GAME EQ KARAOKE PONP FILE

REPEAT

1-680-262-

11

(11)

EFFECTON/OFF

>

+.

–

RECPAUSE/START

D751, S764

CD SYNCHI-DUB

CD-SW BOARD

E

(CD)

ZDISC SKIP/EX-CHANGE

OPENCLOSE

DISC 3

D793, S793

DISC 1

D791, S795

DISC 2

D792, S794E

E

ED794, S796

9 1

KPANEL BOARD

NO602

I/1

S791 – 796

1-680-263-

11

(11)

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9 10

6-16. PRINTED WIRING BOARDS – CD SWITCH/PAD SWITCH Board – • See page 23 for Circuit Boards Location.


Ref. No. Location

D751 F-3D752 C-4D791 A-7D792 A-5D793 A-4D794 A-10

Q751 D-2Q752 C-2Q791 A-8Q792 B-8Q793 A-3Q794 B-10


()

(Page 35)

3838

HCD-DX80

6-17. SCHEMATIC DIAGRAM –LEAF SW Board –


(Page 29)

• Voltages are dc with respect to ground under no-signalconditions.no mark : TAPE PLAY( ) : TAPE REC

3939

HCD-DX80

6-18. PRINTED WIRING BOARDS – LEAF SW/HEAD Board – • See page 23 for Circuit Boards Location. • See page 28 for Schematic Diagram of Head Board.

Ref. No. Location

D1001 B-4D1002 B-10

IC1001 B-2IC1002 B-10

Q1001 B-3



PM901

PM902

F

PO

CN304

IC1001 IC1002

NO303NO302

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9 10 11 12

(Page 30) (Page 30)

(Page 30)

4040

HCD-DX80

6-19. SCHEMATIC DIAGRAM – ADDRESS SENSOR/DRIVER/MOTOR Board – • See page 44 for IC Block Diagram.

(2/4)

IC B/D

(Page 27)

• Voltages are dc with respect to ground under no-signal(detuned) conditions.no mark : CD STOP

4141

HCD-DX80

6-20. PRINTED WIRING BOARDS – ADDRESS SENSOR/DRIVER/MOTOR Board – • See page 23 for Circuit Boards Location.


14

(14)

14

(14)

14

(14)

C712

CN202

A

IC711

IC70

1

A

B

C

D

E

F

G

H

I

1 2 3 4 5 6 7 8

Ref. No. Location

D701 G-1

IC701 G-2IC711 C-6


(Page 30)

4242

HCD-DX806-21. SCHEMATIC DIAGRAM – MAIN TRANS/SUB TRANS Board –

(Page 32)

(Page 32)



4343

HCD-DX80

6-22. PRINTED WIRING BOARDS – MAIN TRANS/SUB TRANS Board – • See page 23 for Circuit Boards Location.


Ref. No. Location

D971 F-7D972 F-8D973 F-8D974 F-7D975 F-7D977 F-1

IC971 F-8

Q971 G-8


4

1

LPOWER AMPLIFIER BOARD

NO501

1-680-265-

11

(11)

T910POWER TRANS FORMER

(MX)

(EXCEPT MX)

SUB TRANS BOARDMAIN TRANS BOARDAC IN

(MX)

VOLTAGE SELECTOR

S901

230 – 240V

220V

110V

(EXCEPT BR)

(EXCEPT MX)

(MX)

T972POWER TRANSFORMER

1

3

3

1E M

POWER AMPLIFIERBOARDCN504

1-680-266-

11

(11)

TOSATELLITE AMPLIFIER

(TA-DX80)

(MX)

*

* NOT REPLACEABLE BUILT IN TRANSFORMER

A

B

C

D

E

F

G

H

1 2 3 4 5 6 7 8 9

(Page 33)

(Page 33)

4444

HCD-DX80

• IC Block Diagrams

– BD Board –

IC101 CXD3017Q

IC102 BA5974FM-E2

1 2 3 10 11 12 13 14 15 16 17 18 19 20

60 59 58 57 56 55 54 52 51 50 49 48 47 46 45 4453

21

39

40

414243

2223

79

24

26

25

28

27

29

30

31

32

35

36

37

38

33

34

80

6261

7778

7576

73

74

72

71

70

69

666564

63

68

67

4 5 6 7 8 9

D/AInterface Digital

PLL

CPUInterface

DigitalOUT

Serial-InInterface

Over SamplingDigital Filter

TimingLogic

PWM

3rd-OrderNoise Shaper

PWM

AsymmetryCorrector

A/DConverter

OP AmpAnalog SW

ClockGenerator

DigitalCLV

MIRRDFCTFOK

SERVO DSP

FOCUSSERVO

TRACKINGSERVO

SELEDSERVO

EFMDemodurator

Servo AutoSequencer

SERVOInterface

ErrorCorrector

16KRAM

Sub CodeProcessor

PWM GENERATOR

FOCUS PWMGENERATOR

TRACKINGPWM

GENERATOR

SLED PWMGENERATOR

SQSO

SQCK

XRST

DATA

XLAT

CLOK

SENS

SCLK

VDD

SPOA

SPOB

XLON

XPCK

SCOR

COUTMIRR

DFCTFOK

LOCK

MDP

SSTP

SFDR

SRDR

TFDR

TRDR

FFDR

FRDR

TEST

TES1

VC

FE

SE

TECERFDC

ADIO

IGEN

ASYO

ASYI

BIAS

RFAC

CLTV

FILO

FILIPC

O

DOUT

XTAIXTAO

AVDD1

AOUT1

AIN1

LOUT1

LOUT2AIN2

AOUT2

LMUT

XVSS

RMUT

SYSM

ATSK

WFC

KXU

GF GFS

C2PO

VSS

XTSL

AVDD

AVSS

AVSS

AVDD

VSS

VDD

LRCKPCMD

BCK

EMPHXVDD

AVSS1

AVSS2

AVDD2

LEVEL SHIFT

INTERFACE

INTERFACE

INTERFACE

1 2 3 4 5 6 7 8 9 10 11 12 13 14

202122232425262728 19 18 17 16 15

F

RRF F

RRF

RR

F

FMUTE

THERMALSHUTDOWN

VREF

OUT

VREF

IN

POW

VCC

CH1F

IN

CH1R

IN

CH2F

IN

CH2R

IN

CH2O

UTR

CH2O

UTF

CH1O

UTR

CH1O

UTF

CAPA

IN1

CAPA

IN2

GND

PRFV

CC

MUT

E

POW

VCC

CH4S

IN'

CH4S

IN

CH4B

IN

CH3F

IN

CH3R

IN

CH3O

UTR

CH3O

UTF

CH4O

UTR

CH4O

UTF

CAPA

IN3

GND

IC103 CXA2581N-T4

RW/ROM

RW/ROM

EQ ON/OFF

VOFST

VOFSTDVC

VC

VC

VC

RW/ROM

VC

DVC

3029

28+–+

–

DVCVCC

DVC

27

262524

RW/ROM

EQ

23

22

21

20

19

RFACVCA

VCC

+–

DVC

+–

+–

RW/ROM

VC

RW/ROM

DVC

+–

3

A

B

C

D

BC

A

A

A

BCD

B C D D

+–

1

2 APC AMP

5

6789

4RFAC

SUMMINGAMP

RW/ROM

APC-OFF(Hi-Z)

RW/ROM(H/L)

VOFST

VC

RW/ROM

+–

10

11

GM

GM

18

17

16

B

D

A

C

13

14

15

12

EQ IN

LD

PD

GND

ABCD

AC SUM

E

F

DVCC

DVC

RFAC

SW

DC OFSTRFDCI

RFDCO

VC

RFCVFCBST

RFG

VCC

CEI

CE

TE BAL

TE

FEI

FE

45

HCD-DX80

1 2 3 4 5 6 7 8 9 10

20 19 18 17 16 15 14 13

1211

21222324

S-CURVE

AM/FMIF

BUFFCOMP

TUNINGDRIVE

AMOSC

AMMIX

AMPF.AMP

AGC

AMIF

AMDET

BUFF

LEVELDET

FMIF FM

DET

REG GND

DEOODERANTI-BIRDIE

P-DETø

PILOTCANCEL

STEREOSW

VCO304kHz

FF38k

FF19k

π2

FF19k 0

PILOTDET

VCC

ALC

PHASEDETECTOR

CHARGE PUMP

SWALLOW COUNTER1/16, 1/17 4BITS

12BITSPROGRAMMABLE

DRIVER

UNIVERSALCOUNTER

REFERENCEDIVIDER

POWERON

RESET1/2

CCBINTERFACE

1 2 3 4 5 6 7 8 9

16 15 14 13 12 11

10

17181920

XOUT

VSS

AOUT

AIN

PD VDD

FMIN

AMIN

XIN

DOCLDICE

IFIN

IO1

BO4

BO3

BO2

BO1

IO2

UNLOCKDETECTOR

DATA SHIFT REGISTER LATCH

1

5

2

43

6

7

8

SELECT A

SELECT B

3

21

0

3

2

1 0

INH

Y1Y3Y

Y1

Y0

VEE

VSS

X3

X0

XX1X2

VDD

A

B9

12

1415

11

16

13

10

IC11 LA1845

IC51 LC72131

IC105 BU4052BCF-E2 IC302 µPC1330HA

1 2 3 4 5 6 7 8 9

INVERTER

COMPARATER

SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2

– MAIN Board –

46

HCD-DX80

IC602 BA3830F-E2 IC701 BA6956AN

2

3

14

1

f04

13 f05

12 f06

11 RECLEVEL

10 VCC

15 f03

5RECNF

6RECIN

7RESETC

8BIASC

9GND1

4

16 f02

17 f01

18 RESETR02

P01

LINENF

LINEIN

REFFERENCECURRENT

BPF DET

BPF DET

BPF DET

BPF DET

DET

RESET

Bias

REFFERENCECURRENT

DET

DET

BPF

BPF

1 2 3 4 5 6 7 8 9

CONTROL LOGIC

TSD

VREF

OUT2

OUT1

RNF

VM VCC

FIN

GND

RIN

– PANEL Board – – DRIVER Board –

47

HCD-DX80

• MAIN BOARD IC501 M30620MCA-A95FP (SYSTEM CONTROLLER)

Pin No. Pin Name I/O Description

1 AUDIO OUT ON/OFF

O Audio output signal on/off control “H”: ON, “L”: OFF Not used (open)

2 STEREO I Stereo detection signal input from the LA1845 (IC11) “L”: Stereo in

3 TUNED I Tuning detection signal input from the LA1845 (IC11) “L”: Tuned in

4 SIRCS I Remote commander receiver signal input terminal

5 SUR1 O Surround control signal output terminal not used (open)



8 GND — Ground terminal

9 GND — Ground terminal

10 XC IN I Sub system clock input terminal (32.768 kHz)

11 XC OUT O Sub system clock output terminal (32.768 kHz)

12 RESET I System reset signal input from the reset signal generator (IC502) “L”: reset

13 X-OUT O Main system clock output terminal (16 MHz)

14 VSS — Ground terminal

15 X-IN I Main system clock input terminal (16 MHz)

16 VCC — Power supply terminal (+5V)

17 NMI I For pull up terminal (connected to Ever +5V)

18 RDS-INT I RDS interrupt signal input terminal Not used (connected to ground)

19 SCOR I Subcode sync (S0+S1) detection signal input from the CXD3017Q (IC101)

20 RDS-DATA I RDS data signal input terminal Not used (connected to ground)

21 ST-MUTE O Muting on/off control signal output to the LA1845 (IC11)

22 ST-CE O PLL chip enable signal output to the FM/AM PLL (IC51)

23 ST-DOUT O PLL serial data output to the FM/AM PLL (IC51)

24 BU-PWM3 O RF data control signal output to the CXA2581N (IC103)

25 ST-DIN I PLL serial data input from the FM/AM PLL (IC51)

26 BU-PWM2 O Tracking error control signal output to the CXA2581N (IC103)

27 ST-CLK O PLL serial data transfer clock signal output to the FM/AM PLL (IC51)

28 BU-PWM1 O Focus error control signal output to the CXA2581N (IC103)

29 IIC-CLK I/O Shift clock signal input/output for the IIC bus

30 IIC-DATA I/O Data input/output terminal for the IIC bus

31 TXD1 O Not used (open)

32 SQ-DATA I Subcode Q data input from the CXD3017Q (IC101)

33 SQ-CLK O Subcode Q data reading clock signal output to the CXD3017Q (IC101)

34 SENS I Internal status detection monitor input from the CXD3017Q (IC101)

35 CD-DATA O Serial data output to the CXD3017Q (IC101)

36 NC — Not used (fixed at “L”)

37 CD-CLK O Serial clock signal output to the CXD3017Q (IC101)

38 CD-POWER O CD power on/off control signal output “L”: on, “H”: off

39 CLOCK-OUT O Clock signal output terminal Not used (open)

40 HOLD O Automatic power control hold signal output to the CXA2581N (IC103)

41 M-RESET O Micom reset signal output to the liquid crystal display driver (IC601) “L”: reset

42 XLT O Serial data latch pulse output to the CXD3017Q (IC101)

43 XRST O CD reset signal output to the CXD3017Q (IC101) and BA5974FM (IC102) “L”: reset

44 LOAD-IN O Turn motor control signal output to the BA6956AN (IC701)

6-23. IC PIN FUNCTION DESCRIPTION

48

HCD-DX80


45 LOAD-OUT O Turn motor control signal output to the BA6956AN (IC701)

46 OPEN-SW I Tray open detect signal input terminal “L”: open

47 CLOSE-SW I Tray close detect signal input terminal “L”: close

48 BU UP/DOWN-SW O Pick-up up/down detect signal input terminal

49 T-SENS I CD table detect signal input from the RPI-321 (IC711)


51 A-TRIG O Deck-A trigger plunger on/off control signal output “H”: plunger on

52 B-TRIG O Deck-B trigger plunger on/off control signal output “H”: plunger on

53 AMS-IN I AMS signal input terminal “L”: AMS in

54 CAPM-H/L O High/normal speed selection signal output of the capstan motor “H”: normal speed, “H”: high speed

55 CAPM-CONTROL O Capstan motor on/off control signal output terminal “H”: motor on

56 A-PLAY I Detection input from the Deck-A play detect switch “H”: deck-A play

57 B-PLAY I Detection input from the Deck-B play detect switch “H”: deck-B play

58 TC-MUTE O Tape deck line muting on/off control output to the HA12226F (IC301) “H”: muting on

59 REC/PB/PAS I Recording/playback/pass selection signal input from the HA12226F (IC301)“L”: recording mode, “Z”: playback mode, “H”: pass mode

60 NR-ON/OFF O Dolby NR on/off selection signal output to the HA12226F (IC301)“H”: dolby on, “L”: dolby off

61 REC-MUTE O Recording muting on/off control signal output to the HA12226F (IC301) “H”: muting on

62 VCC — Power supply terminal (+5V)

63 SOFT TEST O Soft check terminal Not used (open)

64 VSS — Ground terminal

65 BIAS O Recording bias on/off control signal output to the HA12226F (IC301)“H”: bias on, “L”: bias off

66 EQ-H/N O EQ high/normal selection signal output to the HA12226F (IC301)“H”: high, “L”: normal

67 PB-A/B O Deck-A/B selection signal output to the HA12226F (IC301)“L”: deck-A, “H”: deck-B

68 ALC O ALC on/off control signal output to the HA12226F (IC301)“L”: ALC on, “H”: ALC off

69 TC-RELAY O Tape deck relay on/off control signal output to the µPC1330H (IC302)

70 A-HALF I Detection input from the deck-A half detect switch “L”: cassette in, “H”: no cassette



73 DISPLAY KEY I Display key input terminal S752 (DISPLAY)

74 POWER KEY I Power key input terminal S796 (I/1)

75 STBY LED O STANDBY LED on/off control signal output terminal “H”: LED on, “L”: LED off



78 GAME/VIDEO O Game/video selection signal output to the BU4052BCF (IC105)“H”: game in, “L”: video in

79 DBFB ON/OFF O DBFB on/off control signal output terminal “H”: DBFB on, “L”: BDFB off

80 GEQ DATA O Data output for the graphic equalizer IC (IC101)

81 GEQ CLK O Clock output for the graphic equalizer IC (IC101)

82 LINE-MUTE O Audio line muting on/off control signal output terminal “H”: muting on

83 STK-MUTE O Muting on/off control signal output to the power AMP “H”: muting on

49

HCD-DX80


84 STBY-RELAY O Standby relay on/off control signal output to the RY971 “H”: relay on

85 REAR-RELAY O Rear speaker relay on/off control signal output to the STA. AMP (TA-DX80) “H”: relay on

86 SURR-RELAY O Surround speaker relay on/off control signal output terminal “H”: relay on Not used (open)

87 FRONT-RELAY O Front speaker relay on/off control signal output to the RY801 “H”: relay on

88 PROTECT I Speaker protect signal input terminal “L”: protect on

89 A-SHUT I Shut off detection signal input from the deck-A side reel pulse detector

90 B-SHUT I Shut off detection signal input from the deck-B side reel pulse detector

91 B-HALF I Detection input from the deck-B half detect switch “L”: cassette in, “H”: no cassette

92 MODEL-IN I Model select signal input terminal

93 SPEC-IN I Version select signal input terminal

94 FREQ-B O Frequency control signal output to the Booster AMP (TA-DX80)

95 FREQ-A O Frequency control signal output to the Booster AMP (TA-DX80)

96 AVSS — Ground terminal (for analog)

97 BOOSTER-SW I Booster encoder signal input from the satellite AMP (TA-DX80)

98 VREF — Analog reference voltage terminal

99 AVCC — Power supply terminal (+5V) (for analog)

100 AC CUT I AC power off detection signal input from the reset signal generator (IC502)

50

HCD-DX80

• PANEL BOARD IC601 MB90M407PF-G-103-BND (DISPLAY CONTROL)


1 to 5 G5 to G1 O FL grid drive signal output

6 to 10 P1 to P5 O FL segment drive signal output

11 VSS IO — Ground terminal (VSS for I/O)


23 XDD-FIP — Power supply terminal (+3.3V) (VDD for FL Tube)


42 VSS IO — Ground terminal (VSS for I/O)


48 VKK — –32V driving power for FL

49 MD0 I Micom operating mode terminal (fixed at “H”)

50 MD1/VDD-VFT I Micom operating mode terminal (fixed at “H”)

51 MD2 — Micom operating mode terminal (fixed at “L”)

52 REC/PAUSE LED O REC PAUSE/START LED on/off control signal output terminal “H”: LED on, “L”: LED off

53 ENTER LED O ENTER LED on/off control signal output terminal “H”: LED on, “L”: LED off

54 TAPE A/B LED O TAPE A/B LED on/off control signal output terminal “H”: LED on, “L”: LED off

55 TUNER LED O TUNER/BAND LED on/off control signal output terminal “H”: LED on, “L”: LED off

56 MD/VIDEO LED O MD (VIDEO) LED on/off control signal output terminal “H”: LED on, “L”: LED off

57 CD/VCD LED O CD LED on/off control signal output terminal “H”: LED on, “L”: LED off

58 GAME IN LED O GAME LED on/off control signal output terminal “H”: LED on, “L”: LED off

59 DISC 1 LED O DISC 1 LED on/off control signal output terminal “H”: LED on, “L”: LED off

60 IIC DATA I/O Data input/output terminal for the IIC bus

61 IIC CLOCK I/O Shift clock signal input/output terminal for the IIC bus

62 AVCC — Power supply terminal (+3.3V) (for A/D)

63 AVSS — Ground terminal (for A/D)

64 KEY0 IKey input terminal (A/D input)S768 to S781 (PLAY MODE, REPEAT, EDIT, MUSIC EQ, MOVIE EQ, v, ENTER, V,P FILE, GROOVE, SURROUND, g G, X, M keys input)

65 KEY1 IKey input terminal (A/D input) S752 to S758, S760 to S765(DISPLAY, B, b, SPECTRUM, EFECT on/off, GAME EQ, KARAOKE PON, m–, ., x, CD SYNC HI-DUB, REC PAUSE/START, M+ keys input)

66 KEY2 I KEY input terminal (A/D input) S791 to S796(Z OPEN/CLOSE (CD), DISC SKIP/EX-CHANGE, DISC3, DISC2, DISC1, I/1 keys input)

67 to 70 BPF4 to 1 I Band-pass filter input from the BA3830F (IC602)

71SUPER LOW FREQUENCY

(BPF0)I Band-pass filter input from the BA3830F (IC602)

72 BPF5 I Band-pass filter input from the BA3830F (IC602)

73 ALL BAND I All band (L+R) Band-pass filter input from the BA3830F (IC602)



76 VIDEO SWITCH O VIDEO/GAME selection signal output terminal Not used (open) “H”: VIDEO

77 RESET I Reset signal input from the system control (IC501)

78 HEADPHONE I Headphone detect signal input terminal “H”: Headphone Yes, “L”: Headphone No

79 VOL 1B I Jog dial pulse input from the rotary encoder (IC751 VOLUME) B phase input

80 VOL 1A I Jog dial pulse input from the rotary encoder (IC751 VOLUME) A phase input

81 VSS-CPU — Ground terminal (+3.3V) (VSS for CPU)

51

HCD-DX80


82 XOUT O System clock output terminal (4MHz)

83 XIN I System clock input terminal (4MHz)

84 VCC-CPU — Power supply terminal (+3.3V) (VCC for CPU)

85 to 91 NO USE I Not used (open)

92 SOFT TEST O Soft test terminal Not used (open)

93 to 100 G13 to G6 O FL grid drive signal output

52

HCD-DX80

7-1. CABINET SECTION

SECTION 7EXPLODED VIEWS

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.

• The mechanical parts with no reference num-ber in the exploded views are not supplied.

• Accessories and packing materials are givenin the last of the electrical parts list.

• Hardware (# mark) list and accessories andpacking materials are given in the last of theelectrical parts list.

NOTE:• -XX and -X mean standardized parts, so they

may have some difference from the originalone.

• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)

↑ ↑Parts Color Cabinet's Color

• AbbreviationAR : Argentina modelBR : Brazilian modelE2 : 120 V AC Area in EmodelE51 : Chiliean and Peruvian modelMX : Mexican modelSP : Singapore model

CDM58E-30BD60

#1

#1

#1

#1

#1

#1

#2

#1

#1

#1

#1

#1

#1

#1

#1

4

3

52

2

2

26

Front Panel section

Main board section

M9611

8

9

10

12

11

notsupplied

notsupplied

1 4-225-252-01 CUSHION (FOOT)2 3-363-099-41 SCREW (CASE 3 TP2)3 4-225-038-21 SIDE PANEL (L) (EXCEPT BR)3 4-225-038-41 SIDE PANEL (L) (BR)4 4-231-563-21 LOADING PANEL

5 4-225-039-42 SIDE PANEL (R) (BR)5 4-225-039-72 SIDE PANEL (R) (EXCEPT BR)6 4-224-550-41 CASE (TOP) (EXCEPT BR)6 4-224-550-61 CASE (TOP) (BR)8 4-231-580-41 BACK PANEL (EXCEPT MX)

8 4-231-580-51 BACK PANEL (MX)9 1-681-143-11 SENSOR BOARD10 1-680-692-11 VIDEO SWITCH BOARD11 4-233-148-01 GROUND PLATE12 A-2007-964-A SUB TRANS BOARD, COMPLETE (MX)

12 A-4476-114-A SUB TRANS BOARD, COMPLETE (E2, E51, SP, AR)

12 A-4726-060-A SUB TRANS BOARD, COMPLETE (BR)M961 1-763-072-11 FAN, D.C.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

53

HCD-DX80

7-2. FRONT PANEL SECTION


51 A-2004-868-A HOLDER (L) ASSY, TC (BR)51 X-4953-360-1 CASSETTE HOLDER (L) ASSY (EXCEPT BR)52 A-2004-886-A TC HOLDER (R) ASSY (BR)52 X-4953-412-1 CASSETTE HOLDER (R) ASSY (EXCEPT BR)53 4-231-571-01 KNOB (VOLUME)

54 A-4475-778-A PAD SWITCH BOARD, COMPLETE(EXCEPT BR)

54 A-4476-896-A PAD SWITCH BOARD, COMPLETE (BR)57 A-2004-885-A PANEL ASSY, FRONT (BR)57 X-4953-362-1 FRONT PANEL ASSY (EXCEPT BR)60 4-224-104-11 DAMPER

61 4-231-836-01 SPRING (HEART CAM-A)

62 4-231-841-01 SPRING (HEART CAM-B)64 4-231-587-01 SPRING R66 A-4476-112-A PANEL BOARD, COMPLETE (EXCEPT BR)66 A-4726-068-A PANEL BOARD, COMPLETE (BR)67 4-951-620-01 SCREW (2.6X8), +BVTP

68 4-231-805-01 KNOB (MIC)69 4-231-586-01 SPRING L70 4-225-252-01 CUSHION (FOOT)71 1-680-263-11 CD-SW BOARD72 4-225-531-01 BRACKET (RING)

51

52

53

69

57

7072

64

66

67

61

60

60

62

TCM-230AWR41

68

67

67

67

not supplied

not supplied

not supplied

not supplied

54

71

54

HCD-DX80


7-3. MAIN BOARD SECTION


101 1-773-045-11 WIRE (FLAT TYPE) (17 CORE)102 A-2007-962-A MAIN BOARD, COMPLETE (E2, E51)102 A-2007-966-A MAIN BOARD, COMPLETE (MX, AR)102 A-4476-118-A MAIN BOARD, COMPLETE (SP)102 A-4726-064-A MAIN BOARD, COMPLETE (BR)

* 103 4-988-533-01 HOLDER, PWB104 1-757-418-11 WIRE (FLAT TYPE) (21 CORE) (AR)104 1-757-683-11 CABLE, FLAT (21 CORE) (EXCEPT AR)105 1-680-265-11 MAIN TRANS BOARD

* 106 3-703-244-00 BUSHING (2104), CORD

107 A-4476-270-A POWER AMPLIFIER BOARD, COMPLETE (MX)107 A-4476-767-A POWER AMPLIFIER BOARD, COMPLETE

(E2, E51, AR)107 A-4476-770-A POWER AMPLIFIER BOARD, COMPLETE (SP)107 A-4726-062-A POWER AMPLIFIER BOARD, COMPLETE (BR)

0108 1-757-813-21 CORD, POWER (BR)

0108 1-777-071-51 CORD, POWER (EXCEPT BR)0T910 1-437-284-11 TRANSFORMER, POWER (BR)0T910 1-437-355-11 TRANSFORMER, POWER (EXCEPT BR)

#1

#1

#3

#2

#1

#4

103

107

106

101

102

104

105

T910

not supplied

not supplied

108

55

HCD-DX80


7-4. CD MECHANISM DECK SECTION(CDM58E-30BD60)

BU-30BD60

501

502

503

504

505

506

524

525 526

519

507

509

508

508

508

510

511512

513

501

514

521

515

518

530

529

521

534

517

516

521

520

520

520

520533

533

533

508

M721

532

534

501 4-933-134-11 SCREW (+PTPWH M2.6X8)502 4-221-679-01 CAM (RELAY)503 4-231-452-01 TABLE (NEW)504 4-221-686-01 LEVER (CHANGE)505 4-221-676-02 TRAY

506 4-933-134-51 SCREW (+PTPWH 2.6X8)507 1-675-910-14 MOTOR BOARD508 4-951-620-01 SCREW (2.6X8), +BVTP509 1-791-983-12 WIRE (FLAT TYPE) (8 CORE)510 1-675-911-14 ADDRESS SENSOR BOARD

511 1-675-912-14 DRIVER BOARD512 X-4952-608-3 CAM (U/D) ASSY513 4-221-681-01 LEVER (EX)514 4-221-682-01 LEVER (LIFTER)515 4-231-513-01 PULLEY (B) (BU-30), CHUCKING

516 4-228-414-01 BRACKET (YOKE)517 X-4953-307-1 PULLEY (A) ASSY, CHUCKING518 X-4953-306-1 HOLDER (BU) (BU-30) ASSY519 4-222-095-01 BELT520 4-227-045-11 SPRING (INSULATOR), COIL

521 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING524 4-221-678-06 CAM (CONTROL)525 4-221-683-01 GEAR (U)526 4-221-685-01 PULLEY (S)529 4-227-899-01 SCREW (DIA. 12), FROATING

530 4-221-674-03 CHASSIS532 4-222-097-01 SCREW, STEP533 4-231-451-01 INSULATOR (BU-30)534 4-231-151-01 STOPPER (BU)M721 A-4672-826-A MOTOR ASSY (TURN)

Ver 1.1

56

HCD-DX80



7-5. BASE UNIT SECTION(BU-30BD60)

not supplied

not supplied

556

552

551

555

553not supplied

#5 #5

557

551 3-531-576-11 RIVET552 A-4725-531-A BD BOARD, COMPLETE553 4-233-832-01 GEAR (LB)

555 4-233-831-01 GEAR (LA)556 1-757-710-11 WIRE (FLAT TYPE) (16 CORE)

0557 A-4735-188-A BU-30 (60) ASSY

57

HCD-DX80


7-6. TAPE MECHANISM DECK SECTION-1(TCM-230AWR41)

701

701

702

702

703

703

705

705

704

706

706

704HRPE901

HP901

Note: Two different types of tape mechanism are used depending on models. They maintain compatibility as an entire mechanism even though there are some different parts are used.

710

708

707707

709

713

PM901

PM902713

701 3-016-574-11 SPRING (HEAD), TENSION702 3-016-565-01 BASE (PINCH LEVER REV)703 3-016-564-01 BASE (PINCH LEVER FWD)704 X-3374-156-4 PINCH LEVER (REV) ASSY705 X-3374-155-4 PINCH LEVER (FWD) ASSY

706 4-229-083-01 SPRING (CASSETTE), LEAF707 4-227-872-11 SCREW (+PTT 2X4), GROUND POINT708 1-676-220-11 HEAD (A) BOARD

709 1-676-221-11 HEAD (B) BOARD710 A-2007-838-A LEAF SW BOARD, COMPLETE713 3-016-566-01 SLIDER, REVERSEHP901 A-2004-771-A BASE (A) ASSY, HEADHRP901 A-2004-772-A BASE (B) ASSY, HEAD

PM901 1-454-887-32 SOLENOID, PLUNGERPM902 1-454-887-32 SOLENOID, PLUNGER

58

HCD-DX80


7-7. TAPE MECHANISM DECK SECTION-2(TCM-230AWR41)

751

751

752

755

753

754

757

766

767

765

757

763

M901

not supplied

not supplied

#6

#7

#7

756

762

not supplied

764

751 3-041-946-01 BELT (CAPSTAN B)752 4-227-239-01 BELT (CAPSTAN C)753 X-3378-042-1 FLYWHEEL (B-FWD) ASSY754 X-3378-043-1 FLYWHEEL (B-REV) ASSY755 X-3378-040-1 FLYWHEEL (A-FWD) ASSY

756 X-3378-041-1 FLYWHEEL (A-REV) ASSY757 3-041-947-01 BELT (FR)

762 3-318-203-62 SCREW (B1.7X4), TAPPING763 3-019-208-01 WASHER, STOPPER764 3-040-580-11 PULLEY (TENSION)765 4-228-450-11 SPRING (REVERSE SLIDER), TORSION766 A-2004-793-A CHASSIS (A) ASSY, SUB

767 A-2004-794-A CHASSIS (B) ASSY, SUBM901 X-3378-241-1 MOTOR ASSY (CAPSTAN)

59

HCD-DX80

BD

SECTION 8ELECTRICAL PARTS LIST

ADDRESS SENSOR


NOTE:• Due to standardization, replacements in the

parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.

• -XX and -X mean standardized parts, so theymay have some difference from the originalone.

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.

• CAPACITORSuF: µF

• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable

• COILSuH: µH

• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

• AbbreviationAR : Argentina modelBR : Brazilian modelE2 : 120 V AC Area in EmodelE51 : Chiliean and Peruvian modelMX : Mexican modelSP : Singapore model

1-675-911-14 ADDRESS SENSOR BOARD**********************

< CAPACITOR >

C712 1-164-159-11 CERAMIC 0.1uF 50V

< IC >

IC711 8-749-014-38 PHOTO INTERRUPTER SG-264

< RESISTOR >

R711 1-247-876-11 CARBON 75K 5% 1/4WR712 1-249-409-11 CARBON 220 5% 1/4WR713 1-249-429-11 CARBON 10K 5% 1/4W

< SWITCH >

S711 1-771-821-11 SWITCH, PUSH (1 KEY) (UP/DOWN)**************************************************************

A-4725-531-A BD BOARD, COMPLETE*******************

< CAPACITOR >

C101 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC103 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC104 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC108 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C109 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50VC110 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC111 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC112 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC114 1-163-038-11 CERAMIC CHIP 0.1uF 25V

C116 1-104-665-11 ELECT 100uF 20% 10VC117 1-104-665-11 ELECT 100uF 20% 10VC118 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC121 1-163-038-11 CERAMIC CHIP 0.1uF 25VC122 1-124-584-00 ELECT 100uF 20% 10V

C123 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC124 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC125 1-163-038-11 CERAMIC CHIP 0.1uF 25VC126 1-163-038-11 CERAMIC CHIP 0.1uF 25V

C127 1-124-584-00 ELECT 100uF 20% 10V

C129 1-162-974-11 CERAMIC CHIP 0.01uF 50VC130 1-163-038-11 CERAMIC CHIP 0.1uF 25VC131 1-104-665-11 ELECT 100uF 20% 10VC133 1-162-921-11 CERAMIC CHIP 33PF 5% 50VC143 1-163-038-11 CERAMIC CHIP 0.1uF 25V

C145 1-163-038-11 CERAMIC CHIP 0.1uF 25VC153 1-163-038-11 CERAMIC CHIP 0.1uF 25VC159 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC162 1-104-665-11 ELECT 100uF 20% 10VC165 1-163-038-11 CERAMIC CHIP 0.1uF 25V

C167 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC168 1-162-921-11 CERAMIC CHIP 33PF 5% 50VC171 1-115-412-11 CERAMIC CHIP 680PF 5% 25VC172 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC181 1-115-412-11 CERAMIC CHIP 680PF 5% 25V

C182 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC183 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC184 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC185 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC190 1-115-156-11 CERAMIC CHIP 1uF 10V

C191 1-124-584-00 ELECT 100uF 20% 10VC192 1-163-038-11 CERAMIC CHIP 0.1uF 25VC193 1-104-665-11 ELECT 100uF 20% 10VC194 1-163-038-11 CERAMIC CHIP 0.1uF 25VC195 1-163-038-11 CERAMIC CHIP 0.1uF 25V

C196 1-163-038-11 CERAMIC CHIP 0.1uF 25VC197 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC198 1-124-584-00 ELECT 100uF 20% 10V

< CONNECTOR >

CN101 1-568-864-11 CONNECTOR, FFC 21PCN102 1-793-907-11 CONNECTOR, FFC/FPC 16P

< DIODE >

D101 8-719-422-12 DIODE UDZ-TE-17-3.9B

< FERRITE BEAD >

FB101 1-500-445-21 FERRITE 0uHFB102 1-500-445-21 FERRITE 0uH


60

HCD-DX80

BD CD-SW

< IC >

IC101 8-752-402-31 IC CXD3017QIC102 8-759-827-41 IC BA5974FM-E2IC103 8-752-089-74 IC CXA2581N-T4

< JUMPER RESISTOR >

JR101 1-216-295-11 SHORT 0JR102 1-216-295-11 SHORT 0JR103 1-216-295-11 SHORT 0JR104 1-216-295-11 SHORT 0JR105 1-216-295-11 SHORT 0


< COIL >

L101 1-469-553-21 INDUCTOR 4.7uH

< TRANSISTOR >

Q101 8-729-010-08 TRANSISTOR MSB710-RT1Q102 8-729-920-85 TRANSISTOR 2SD1664-T100-QR

< RESISTOR >

R101 1-216-049-11 RES-CHIP 1K 5% 1/10WR102 1-216-097-11 RES-CHIP 100K 5% 1/10WR103 1-216-077-00 RES-CHIP 15K 5% 1/10WR104 1-216-085-00 METAL CHIP 33K 5% 1/10WR105 1-216-049-11 RES-CHIP 1K 5% 1/10W

R106 1-216-049-11 RES-CHIP 1K 5% 1/10WR107 1-216-073-00 METAL CHIP 10K 5% 1/10WR108 1-216-061-00 METAL CHIP 3.3K 5% 1/10WR109 1-216-121-11 RES-CHIP 1M 5% 1/10WR111 1-216-099-00 METAL CHIP 120K 5% 1/10W

R114 1-218-745-11 RES-CHIP 160K 5% 1/16WR116 1-216-001-00 METAL CHIP 10 5% 1/10WR117 1-216-049-11 RES-CHIP 1K 5% 1/10WR118 1-216-025-11 RES-CHIP 100 5% 1/10WR119 1-216-059-00 METAL CHIP 2.7K 5% 1/10W

R120 1-216-077-00 RES-CHIP 15K 5% 1/10WR122 1-216-097-11 RES-CHIP 100K 5% 1/10WR123 1-216-073-00 METAL CHIP 10K 5% 1/10WR124 1-216-097-11 RES-CHIP 100K 5% 1/10WR131 1-216-033-00 METAL CHIP 220 5% 1/10W

R143 1-216-085-00 METAL CHIP 33K 5% 1/10WR144 1-216-085-00 METAL CHIP 33K 5% 1/10WR147 1-216-059-00 METAL CHIP 2.7K 5% 1/10WR148 1-216-001-00 METAL CHIP 10 5% 1/10WR149 1-216-001-00 METAL CHIP 10 5% 1/10W

R158 1-216-083-00 METAL CHIP 27K 5% 1/10WR159 1-216-083-00 METAL CHIP 27K 5% 1/10WR162 1-216-097-11 RES-CHIP 100K 5% 1/10WR171 1-216-081-00 METAL CHIP 22K 5% 1/10WR172 1-216-081-00 METAL CHIP 22K 5% 1/10W

R173 1-216-081-00 METAL CHIP 22K 5% 1/10W

R181 1-216-081-00 METAL CHIP 22K 5% 1/10WR182 1-216-081-00 METAL CHIP 22K 5% 1/10WR183 1-216-081-00 METAL CHIP 22K 5% 1/10WR190 1-216-033-00 METAL CHIP 220 5% 1/10W

R191 1-216-085-00 METAL CHIP 33K 5% 1/10WR192 1-216-085-00 METAL CHIP 33K 5% 1/10WR193 1-216-099-00 METAL CHIP 120K 5% 1/10WR194 1-216-097-11 RES-CHIP 100K 5% 1/10WR195 1-216-113-00 METAL CHIP 470K 5% 1/10W

R196 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR198 1-216-295-11 SHORT 0

< COMPOSITION CIRCUIT BLOCK >

RN101 1-233-576-11 RES, CHIP NETWORK 100

< VARIABLE RESISTOR >

RV101 1-238-602-11 RES, ADJ, CARBON 47K

< VIBRATOR >

X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz)**************************************************************

1-680-263-11 CD-SW BOARD************

< LED >

D791 8-719-057-97 LED SEL5923A-TP15 (DISC 1)D792 8-719-057-97 LED SEL5923A-TP15 (DISC 2)D793 8-719-057-97 LED SEL5923A-TP15 (DISC 3)D794 8-719-071-44 LED SEL5223C-TP15 (I/1)

< TRANSISTOR >

Q791 8-729-900-80 TRANSISTOR BA1A4M-TPQ792 8-729-900-80 TRANSISTOR BA1A4M-TPQ793 8-729-900-80 TRANSISTOR BA1A4M-TPQ794 8-729-900-80 TRANSISTOR BA1A4M-TP

< RESISTOR >

R791 1-249-419-11 CARBON 1.5K 5% 1/4WR792 1-249-421-11 CARBON 2.2K 5% 1/4WR793 1-249-422-11 CARBON 2.7K 5% 1/4WR794 1-249-424-11 CARBON 3.9K 5% 1/4WR795 1-249-426-11 CARBON 5.6K 5% 1/4W

R796 1-249-410-11 CARBON 270 5% 1/4WR798 1-249-409-11 CARBON 220 5% 1/4WR799 1-249-409-11 CARBON 220 5% 1/4WR800 1-249-417-11 CARBON 1K 5% 1/4WR801 1-249-409-11 CARBON 220 5% 1/4W

< SWITCH >

S791 1-771-410-21 SWITCH, TACTILE (Z OPEN/CLOSE)S792 1-771-410-21 SWITCH, TACTILE (DISK SKIP/EX-CHANGE)S793 1-771-410-21 SWITCH, TACTILE (DISC 3)S794 1-771-410-21 SWITCH, TACTILE (DISC 2)S795 1-771-410-21 SWITCH, TACTILE (DISC 1)

S796 1-771-410-21 SWITCH, TACTILE (I/1)**************************************************************


61

HCD-DX80

DRIVER HEAD (A) HEAD (B) LEAF SW MAIN

1-675-912-14 DRIVER BOARD*************

< CAPACITOR >

C702 1-126-964-51 ELECT 10uF 20% 50V

< CONNECTOR >

CN701 1-785-336-11 PIN, CONNECTOR (LIGHT ANGLE) 10PCN702 1-785-550-11 CONNECTOR, FFC/FPC 8P

< DIODE >

D701 8-719-983-68 DIODE MTZJ-T-72-3.9A

< IC >

IC701 8-759-598-69 IC BA6956AN

< RESISTOR >

R701 1-249-411-11 CARBON 330 5% 1/4WR702 1-249-401-11 CARBON 47 5% 1/4W

**************************************************************

1-676-220-11 HEAD (A) BOARD**************

< CONNECTOR >

* CN1 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P**************************************************************

1-676-221-11 HEAD (B) BOARD**************

< CONNECTOR >

CN2 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P**************************************************************

A-2007-838-A LEAF SW BOARD, COMPLETE************************

< CAPACITOR >

C1001 1-107-716-11 ELECT 33uF 20% 10V

< CONNECTOR >

CN1001 1-568-860-21 SOCKET, CONNECTOR 17P

< DIODE >

D1001 8-719-911-19 DIODE 1SS133T-72D1002 8-719-911-19 DIODE 1SS133T-72

< IC >

IC1001 8-749-014-38 PHOTO INTERRUPTER SG-264IC1002 8-749-014-38 PHOTO INTERRUPTER SG-264

< TRANSISTOR >

Q1001 8-729-029-56 TRANSISTOR DTA144ESA-TP

< RESISTOR >

R907 1-247-879-11 CARBON 100K 5% 1/4WR1001 1-249-409-11 CARBON 220 5% 1/4WR1002 1-249-409-11 CARBON 220 5% 1/4WR1003 1-249-414-11 CARBON 560 5% 1/4WR1004 1-247-834-11 CARBON 1.3K 5% 1/4W

R1005 1-247-818-11 CARBON 300 5% 1/4WR1006 1-247-864-11 CARBON 24K 5% 1/4WR1007 1-247-780-00 CARBON 7.5 5% 1/4WR1008 1-249-417-11 CARBON 1K 5% 1/4W


RV1001 1-241-785-11 RES, ADJ, CARBON 10KRV1002 1-241-785-11 RES, ADJ, CARBON 10K

< SWITCH >

S1001 1-570-953-11 SWITCH, PUSH (1 KEY) (A PLAY)S1002 1-570-953-11 SWITCH, PUSH (1 KEY) (B PLAY)S1003 1-771-333-11 SWITCH, LEAF (A·HALF)S1004 1-771-205-11 SWITCH, LEAF (A·120/70)S1005 1-771-205-11 SWITCH, LEAF (REC·A)

S1006 1-771-333-11 SWITCH, LEAF (B·HALF)S1008 1-771-205-11 SWITCH, LEAF (B·120/70)S1009 1-771-205-11 SWITCH, LEAF (REC·B)

**************************************************************

A-2007-962-A MAIN BOARD, COMPLETE (E2, E51)A-2007-966-A MAIN BOARD, COMPLETE (MX, AR)A-4726-064-A MAIN BOARD, COMPLETE (BR)A-4476-118-A MAIN BOARD, COMPLETE (SP)

*********************

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

< CAPACITOR >

C1 1-162-974-11 CERAMIC CHIP 0.01uF 50VC2 1-162-974-11 CERAMIC CHIP 0.01uF 50VC3 1-104-664-11 ELECT 47uF 20% 16VC4 1-162-974-11 CERAMIC CHIP 0.01uF 50VC5 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C7 1-216-864-11 SHORT 0C11 1-162-974-11 CERAMIC CHIP 0.01uF 50VC12 1-104-664-11 ELECT 47uF 20% 16VC13 1-162-974-11 CERAMIC CHIP 0.01uF 50VC14 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C15 1-162-974-11 CERAMIC CHIP 0.01uF 50VC16 1-104-664-11 ELECT 47uF 20% 16VC17 1-126-959-11 ELECT 0.47uF 20% 50VC18 1-126-960-11 ELECT 1uF 20% 50VC19 1-126-960-11 ELECT 1uF 20% 50V

C20 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC21 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC22 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC23 1-164-360-11 CERAMIC CHIP 0.1uF 16VC24 1-126-963-11 ELECT 4.7uF 20% 50V

C25 1-126-964-11 ELECT 10uF 20% 50VC26 1-164-471-11 CERAMIC CHIP 680PF 5% 50VC27 1-162-974-11 CERAMIC CHIP 0.01uF 50V


62

HCD-DX80

C28 1-126-963-11 ELECT 4.7uF 20% 50VC29 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C30 1-126-962-11 ELECT 3.3uF 20% 50VC31 1-162-974-11 CERAMIC CHIP 0.01uF 50VC32 1-126-963-11 ELECT 4.7uF 20% 50VC34 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC35 1-104-664-11 ELECT 47uF 20% 16V

C36 1-126-963-11 ELECT 4.7uF 20% 50VC38 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC39 1-164-361-11 CERAMIC CHIP 0.047uF 16VC40 1-164-361-11 CERAMIC CHIP 0.047uF 16VC41 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V

C42 1-162-940-11 CERAMIC CHIP 9PF 0.5PF 50VC43 1-162-974-11 CERAMIC CHIP 0.01uF 50VC46 1-162-974-11 CERAMIC CHIP 0.01uF 50VC51 1-162-920-11 CERAMIC CHIP 27PF 5% 50VC52 1-162-920-11 CERAMIC CHIP 27PF 5% 50V

C53 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC55 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC56 1-162-974-11 CERAMIC CHIP 0.01uF 50VC57 1-104-664-11 ELECT 47uF 20% 16VC58 1-126-961-11 ELECT 2.2uF 20% 50V

C59 1-162-974-11 CERAMIC CHIP 0.01uF 50VC60 1-104-664-11 ELECT 47uF 20% 16VC61 1-162-974-11 CERAMIC CHIP 0.01uF 50VC62 1-126-959-11 ELECT 0.47uF 20% 50VC63 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C69 1-162-974-11 CERAMIC CHIP 0.01uF 50VC101 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC102 1-126-961-11 ELECT 2.2uF 20% 50VC103 1-126-964-11 ELECT 10uF 20% 50VC104 1-126-964-11 ELECT 10uF 20% 50V

C105 1-126-964-11 ELECT 10uF 20% 50VC106 1-136-161-00 FILM 0.047uF 5% 50VC107 1-136-495-11 FILM 0.068uF 5% 50VC108 1-136-495-11 FILM 0.068uF 5% 50VC109 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V

C110 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC111 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25VC112 1-126-961-11 ELECT 2.2uF 20% 50VC113 1-126-957-11 ELECT 0.22uF 20% 50VC115 1-136-169-00 FILM 0.22uF 5% 50V

C116 1-136-169-00 FILM 0.22uF 5% 50VC117 1-126-964-11 ELECT 10uF 20% 50VC118 1-126-961-11 ELECT 2.2uF 20% 50VC121 1-126-964-11 ELECT 10uF 20% 50VC122 1-126-964-11 ELECT 10uF 20% 50V

C123 1-126-964-11 ELECT 10uF 20% 50VC124 1-164-156-11 CERAMIC CHIP 0.1uF 25VC127 1-126-961-11 ELECT 2.2uF 20% 50VC128 1-126-963-11 ELECT 4.7uF 20% 50VC129 1-126-963-11 ELECT 4.7uF 20% 50V

C130 1-162-947-11 CERAMIC CHIP 33PF 5% 50VC131 1-136-169-00 FILM 0.22uF 5% 50VC132 1-126-964-11 ELECT 10uF 20% 50VC133 1-126-935-11 ELECT 470uF 20% 10VC134 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C135 1-126-964-11 ELECT 10uF 20% 50VC136 1-126-964-11 ELECT 10uF 20% 50VC137 1-126-964-11 ELECT 10uF 20% 50VC139 1-126-935-11 ELECT 470uF 20% 10VC140 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C141 1-162-947-11 CERAMIC CHIP 33PF 5% 50VC142 1-164-156-11 CERAMIC CHIP 0.1uF 25VC144 1-126-964-11 ELECT 10uF 20% 50VC146 1-126-935-11 ELECT 470uF 20% 10VC149 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C150 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC151 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC152 1-126-961-11 ELECT 2.2uF 20% 50VC153 1-126-964-11 ELECT 10uF 20% 50VC154 1-126-964-11 ELECT 10uF 20% 50V

C155 1-126-964-11 ELECT 10uF 20% 50VC156 1-136-161-00 FILM 0.047uF 5% 50VC157 1-136-495-11 FILM 0.068uF 5% 50VC158 1-136-495-11 FILM 0.068uF 5% 50VC159 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V

C160 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC161 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25VC162 1-126-961-11 ELECT 2.2uF 20% 50VC165 1-136-169-00 FILM 0.22uF 5% 50VC166 1-136-169-00 FILM 0.22uF 5% 50V

C167 1-126-964-11 ELECT 10uF 20% 50VC171 1-126-964-11 ELECT 10uF 20% 50VC172 1-126-964-11 ELECT 10uF 20% 50VC177 1-126-961-11 ELECT 2.2uF 20% 50VC178 1-126-963-11 ELECT 4.7uF 20% 50V

C179 1-126-963-11 ELECT 4.7uF 20% 50VC180 1-162-947-11 CERAMIC CHIP 33PF 5% 50VC191 1-162-947-11 CERAMIC CHIP 33PF 5% 50VC201 1-104-665-11 ELECT 100uF 20% 10VC202 1-126-916-11 ELECT 1000uF 20% 6.3V

C203 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC205 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC207 1-126-916-11 ELECT 1000uF 20% 6.3VC208 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC209 1-126-935-11 ELECT 470uF 20% 10V

C212 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC213 1-163-005-91 CERAMIC CHIP 470PF 10% 50VC215 1-126-964-11 ELECT 10uF 20% 50VC216 1-163-005-91 CERAMIC CHIP 470PF 10% 50VC224 1-113-619-11 CERAMIC CHIP 0.47uF 10V

C226 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC228 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC301 1-126-960-11 ELECT 1uF 20% 50VC302 1-130-479-00 MYLAR 0.0047uF 5% 50VC303 1-136-165-00 FILM 0.1uF 5% 50V

C304 1-136-165-00 FILM 0.1uF 5% 50VC305 1-126-964-11 ELECT 10uF 20% 50VC306 1-126-960-11 ELECT 1uF 20% 50VC307 1-126-959-11 ELECT 0.47uF 20% 50VC308 1-126-964-11 ELECT 10uF 20% 50V

C309 1-137-194-81 FILM 0.47uF 5% 50VC310 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC311 1-126-964-11 ELECT 10uF 20% 50V

MAIN


63

HCD-DX80

C312 1-126-959-11 ELECT 0.47uF 20% 50VC313 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C314 1-126-964-11 ELECT 10uF 20% 50VC315 1-126-963-11 ELECT 4.7uF 20% 50VC316 1-126-933-11 ELECT 100uF 20% 16VC317 1-104-665-11 ELECT 100uF 20% 10VC318 1-126-964-11 ELECT 10uF 20% 50V

C319 1-126-961-11 ELECT 2.2uF 20% 50VC320 1-126-961-11 ELECT 2.2uF 20% 50VC321 1-164-392-11 CERAMIC CHIP 390PF 10% 50VC322 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC323 1-130-487-00 MYLAR 0.022uF 5% 50V

C324 1-126-964-11 ELECT 10uF 20% 50VC325 1-126-965-11 ELECT 22uF 20% 50VC326 1-164-392-11 CERAMIC CHIP 390PF 10% 50VC327 1-104-665-11 ELECT 100uF 20% 10VC328 1-162-953-11 CERAMIC CHIP 100PF 5% 50V

C329 1-130-483-00 MYLAR 0.01uF 5% 50VC330 1-126-964-11 ELECT 10uF 20% 50VC331 1-126-965-11 ELECT 22uF 20% 50VC332 1-137-427-11 MYLAR 120PF 5% 50VC333 1-162-961-11 CERAMIC CHIP 330PF 10% 50V

C334 1-162-946-11 CERAMIC CHIP 27PF 5% 50VC335 1-137-150-11 MYLAR 0.01uF 5% 100VC336 1-126-961-11 ELECT 2.2uF 20% 50VC337 1-130-485-00 MYLAR 0.015uF 5% 50VC338 1-130-481-00 MYLAR 0.0068uF 5% 50V

C339 1-130-481-00 MYLAR 0.0068uF 5% 50VC340 1-130-486-00 MYLAR 0.018uF 10% 50VC341 1-126-960-11 ELECT 1uF 20% 50VC342 1-104-664-11 ELECT 47uF 20% 16VC351 1-126-960-11 ELECT 1uF 20% 50V

C352 1-130-479-00 MYLAR 0.0047uF 5% 50VC353 1-136-165-00 FILM 0.1uF 5% 50VC354 1-136-165-00 FILM 0.1uF 5% 50VC355 1-126-964-11 ELECT 10uF 20% 50VC356 1-126-960-11 ELECT 1uF 20% 50V

C357 1-126-959-11 ELECT 0.47uF 20% 50VC358 1-126-964-11 ELECT 10uF 20% 50VC359 1-137-194-81 FILM 0.47uF 5% 50VC360 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC362 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

C363 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC368 1-126-964-11 ELECT 10uF 20% 50VC369 1-126-961-11 ELECT 2.2uF 20% 50VC370 1-126-961-11 ELECT 2.2uF 20% 50VC371 1-164-392-11 CERAMIC CHIP 390PF 10% 50V

C372 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC373 1-130-487-00 MYLAR 0.022uF 5% 50VC374 1-126-964-11 ELECT 10uF 20% 50VC375 1-126-965-11 ELECT 22uF 20% 50VC376 1-164-392-11 CERAMIC CHIP 390PF 10% 50V

C377 1-104-665-11 ELECT 100uF 20% 10VC378 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC379 1-130-483-00 MYLAR 0.01uF 5% 50VC380 1-126-964-11 ELECT 10uF 20% 50VC381 1-126-965-11 ELECT 22uF 20% 50V

C382 1-137-427-11 MYLAR 120PF 5% 50VC383 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC384 1-162-946-11 CERAMIC CHIP 27PF 5% 50VC385 1-126-964-11 ELECT 10uF 20% 50VC395 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C504 1-109-953-11 ELECT 2.2uF 20% 50VC505 1-164-156-11 CERAMIC CHIP 0.1uF 25VC510 1-162-918-11 CERAMIC CHIP 18PF 5% 50VC511 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC512 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C514 1-164-156-11 CERAMIC CHIP 0.1uF 25VC516 1-126-916-11 ELECT 1000uF 20% 6.3VC530 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC546 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC562 1-104-665-11 ELECT 100uF 20% 10V

C564 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC575 1-136-165-00 FILM 0.1uF 5% 50VC576 1-136-165-00 FILM 0.1uF 5% 50VC577 1-126-964-11 ELECT 10uF 20% 50VC588 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C596 1-164-156-11 CERAMIC CHIP 0.1uF 25VC598 1-164-156-11 CERAMIC CHIP 0.1uF 25VC599 1-126-964-11 ELECT 10uF 20% 50VC701 1-126-964-11 ELECT 10uF 20% 50VC702 1-126-964-11 ELECT 10uF 20% 50V

C751 1-126-964-11 ELECT 10uF 20% 50VC752 1-126-964-11 ELECT 10uF 20% 50VC803 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC821 1-104-665-11 ELECT 100uF 20% 10VC822 1-126-961-11 ELECT 2.2uF 20% 50V

C824 1-126-960-11 ELECT 1uF 20% 50VC841 1-126-959-11 ELECT 0.47uF 20% 50VC853 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC861 1-107-717-11 ELECT 47uF 20% 50VC862 1-107-721-11 ELECT 4.7uF 20% 100V

C863 1-107-721-11 ELECT 4.7uF 20% 100VC891 1-126-964-11 ELECT 10uF 20% 50VC892 1-164-156-11 CERAMIC CHIP 0.1uF 25VC901 1-126-944-11 ELECT 3300uF 20% 25VC902 1-136-165-00 FILM 0.1uF 5% 50V

C903 1-136-165-00 FILM 0.1uF 5% 50VC905 1-136-165-00 FILM 0.1uF 5% 50VC906 1-136-165-00 FILM 0.1uF 5% 50VC907 1-128-548-11 ELECT 4700uF 20% 25VC908 1-126-942-61 ELECT 1000uF 20% 25V

C909 1-126-952-11 ELECT 1000uF 20% 35VC911 1-126-956-91 ELECT 0.1uF 20% 50VC912 1-126-916-11 ELECT 1000uF 20% 6.3VC921 1-126-956-91 ELECT 0.1uF 20% 50VC922 1-126-933-11 ELECT 100uF 20% 16V

C925 1-104-665-11 ELECT 100uF 20% 10VC932 1-126-935-11 ELECT 470uF 20% 10VC951 1-126-960-11 ELECT 1uF 20% 50VC961 1-126-960-11 ELECT 1uF 20% 50VC962 1-126-926-11 ELECT 1000uF 20% 10V

< FILTER >

CF1 1-760-023-11 FILTER, CERAMIC

MAIN


64

HCD-DX80

CF2 1-760-023-11 FILTER, CERAMIC

< CONNECTOR >

* CN101 1-565-291-11 SOCKET, CONNECTOR 13PCN201 1-569-914-11 S0CKET, CONNECTOR 21PCN202 1-785-336-11 PIN, CONNECTOR (LIGHT ANGLE) 10P

* CN301 1-568-449-11 HOUSING, CONNECTOR (PC BOARD) 3P* CN304 1-569-934-11 SOCKET, CONNECTOR 17P

CN401 1-793-766-11 CONNECTOR, BOARD TO BOARD 30PCN402 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4PCN891 1-564-506-11 PLUG, CONNECTOR 3PCN901 1-778-982-21 CONNECTOR, BOARD TO BOARD 13PCN902 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P

< DIODE >

D51 8-719-988-61 DIODE 1SS355TE-17D508 8-719-988-61 DIODE 1SS355TE-17D509 8-719-988-61 DIODE 1SS355TE-17D510 8-719-988-61 DIODE 1SS355TE-17D511 8-719-988-61 DIODE 1SS355TE-17



D861 8-719-988-61 DIODE 1SS355TE-17D892 8-719-988-61 DIODE 1SS355TE-17D893 8-719-988-61 DIODE 1SS355TE-17D901 8-719-083-89 DIODE 11ES2N-TB5D902 8-719-083-89 DIODE 11ES2N-TB5

D903 8-719-083-89 DIODE 11ES2N-TB5D904 8-719-083-89 DIODE 11ES2N-TB5D906 8-719-083-89 DIODE 11ES2N-TB5D907 8-719-083-89 DIODE 11ES2N-TB5D908 8-719-083-89 DIODE 11ES2N-TB5

D909 8-719-083-89 DIODE 11ES2N-TB5D910 8-719-083-89 DIODE 11ES2N-TB5D911 8-719-083-89 DIODE 11ES2N-TB5D912 8-719-083-89 DIODE 11ES2N-TB5D920 8-719-083-89 DIODE 11ES2N-TB5

D921 8-719-083-89 DIODE 11ES2N-TB5D922 8-719-083-89 DIODE 11ES2N-TB5D952 8-719-988-61 DIODE 1SS355TE-17D953 8-719-988-61 DIODE 1SS355TE-17

< FERRITE BEAD >

FB201 1-216-864-11 SHORT 0FB203 1-216-864-11 SHORT 0FB204 1-216-864-11 SHORT 0FB516 1-216-864-11 SHORT 0FB562 1-216-864-11 SHORT 0

FB599 1-216-864-11 SHORT 0

< FRONT END >

FE1 1-693-477-12 FRONT END (3 GANGS) (FM FRONT-END)

< IC >

IC11 8-759-828-33 IC LA1845IC51 8-759-584-70 IC LC72131IC101 8-759-652-04 IC M61504FP-TPIC102 8-759-710-97 IC NJM4565M (TE2)IC104 8-759-710-97 IC NJM4565M (TE2)

IC105 8-759-525-25 IC BU4052BCF-E2IC106 8-759-710-97 IC NJM4565M (TE2)IC201 8-749-923-04 IC TOTX178A (OPTICAL CD DIGITAL OUT)IC202 8-759-491-46 IC TC74VHCT04AFT (EL)IC301 8-759-652-02 IC HA12226F

IC302 8-759-143-54 IC uPC1330HAIC303 8-759-656-83 IC NJM4580MD-TEIC304 8-759-656-83 IC NJM4580MD-TEIC501 8-759-829-45 IC M30620MCA-A95FPIC502 8-759-635-63 IC M51943BSL-TP

IC701 8-759-710-97 IC NJM4565M (TE2)IC911 8-759-039-69 IC uPC7805AHFIC921 8-759-088-08 IC uPC7812AHFIC951 8-759-158-62 IC TA78057SIC961 8-759-701-59 IC AN7809

< IFT >

IFT11 1-435-848-11 TRANSFORMER, IF (CERAMIC FILTER)

< JACK >

J101 1-793-987-11 JACK, PIN 2P (MD/VIDEO (AUDIO) IN)

< JUMPER RESISTOR >






MAIN


65

HCD-DX80


JR501 1-216-864-11 SHORT 0JR801 1-216-864-11 SHORT 0JR806 1-216-864-11 SHORT 0JR922 1-216-845-11 METAL CHIP 100K 5% 1/16W

< COIL >

L101 1-414-189-31 INDUCTOR 100uHL201 1-414-189-31 INDUCTOR 100uHL301 1-410-780-11 INDUCTOR 27uHL302 1-414-193-41 INDUCTOR 220uHL303 1-414-193-41 INDUCTOR 220uH

L351 1-410-780-11 INDUCTOR 27uH

< FILTER >

LPF11 1-234-612-11 FILTER, LOW PASSLPF12 1-234-612-11 FILTER, LOW PASS

< TRANSISTOR >

Q1 8-729-055-80 TRANSISTOR 2SC1674LK-TPQ2 8-729-113-69 TRANSISTOR FN1F4M-T1M32Q11 8-729-620-05 TRANSISTOR 2SC2603TP-EFQ12 8-729-620-05 TRANSISTOR 2SC2603TP-EFQ101 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6

Q102 8-729-144-85 FET 2SK1133-T1BQ103 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q104 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q141 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6Q151 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6

Q152 8-729-144-85 FET 2SK1133-T1BQ153 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q301 8-729-801-93 TRANSISTOR 2SD1387-34-TPQ302 8-729-142-46 TRANSISTOR 2SC2001TP-LKQ303 8-729-142-46 TRANSISTOR 2SC2001TP-LK

Q304 8-729-113-69 TRANSISTOR FN1F4M-T1M32Q305 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q391 8-729-140-04 TRANSISTOR 2SB1116-TP-LKQ392 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q393 8-729-140-04 TRANSISTOR 2SB1116-TP-LK

Q394 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q395 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q396 8-729-116-57 TRANSISTOR 2SB1068TP-KQ397 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q503 8-729-113-13 TRANSISTOR FA1A4M-T1L33

Q504 8-729-113-69 TRANSISTOR FN1F4M-T1M32Q505 8-729-113-13 TRANSISTOR FA1A4M-T1L33Q575 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6Q821 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6Q822 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6

Q823 8-729-216-22 TRANSISTOR 2SA812-T1-M5M6Q824 8-729-014-97 TRANSISTOR FA1L3Z-T1BQ825 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6Q828 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6

Q829 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6

Q831 8-729-113-69 TRANSISTOR FN1F4M-T1M32Q832 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6Q861 8-729-113-69 TRANSISTOR FN1F4M-T1M32Q862 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q863 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16

Q891 8-729-140-04 TRANSISTOR 2SB1116-TP-LKQ892 8-729-620-05 TRANSISTOR 2SC2603TP-EFQ911 8-729-141-83 TRANSISTOR 2SB1375

Q912 8-729-113-13 TRANSISTOR FA1A4M-T1L33

< RESISTOR >

R1 1-216-864-11 SHORT 0R3 1-216-805-11 METAL CHIP 47 5% 1/16WR4 1-216-805-11 METAL CHIP 47 5% 1/16WR5 1-216-819-11 METAL CHIP 680 5% 1/16WR6 1-216-815-11 METAL CHIP 330 5% 1/16W

R7 1-216-819-11 METAL CHIP 680 5% 1/16WR8 1-216-821-11 METAL CHIP 1K 5% 1/16WR10 1-216-814-11 METAL CHIP 270 5% 1/16WR12 1-216-833-11 METAL CHIP 10K 5% 1/16WR13 1-216-827-11 METAL CHIP 3.3K 5% 1/16W

R14 1-216-814-11 METAL CHIP 270 5% 1/16WR15 1-216-843-11 METAL CHIP 68K 5% 1/16WR16 1-216-837-11 METAL CHIP 22K 5% 1/16WR17 1-216-839-11 METAL CHIP 33K 5% 1/16WR18 1-216-827-11 METAL CHIP 3.3K 5% 1/16W

R19 1-216-833-11 METAL CHIP 10K 5% 1/16WR20 1-216-827-11 METAL CHIP 3.3K 5% 1/16WR21 1-216-820-11 METAL CHIP 820 5% 1/16W

(E2, E51, BR)R21 1-216-819-11 METAL CHIP 680 5% 1/16W

(SP, MX, AR)R22 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

R23 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR24 1-216-820-11 METAL CHIP 820 5% 1/16W

(E2, E51, BR)R24 1-216-819-11 METAL CHIP 680 5% 1/16W

(SP, MX, AR)R25 1-216-809-11 METAL CHIP 100 5% 1/16WR26 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

R27 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR28 1-216-849-11 METAL CHIP 220K 5% 1/16WR29 1-216-849-11 METAL CHIP 220K 5% 1/16WR30 1-216-827-11 METAL CHIP 3.3K 5% 1/16WR31 1-216-829-11 METAL CHIP 4.7K 5% 1/16W

R41 1-216-833-11 METAL CHIP 10K 5% 1/16WR42 1-216-845-11 METAL CHIP 100K 5% 1/16WR43 1-216-839-11 METAL CHIP 33K 5% 1/16WR55 1-216-833-11 METAL CHIP 10K 5% 1/16WR56 1-216-833-11 METAL CHIP 10K 5% 1/16W

R58 1-216-809-11 METAL CHIP 100 5% 1/16WR59 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR60 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR61 1-216-809-11 METAL CHIP 100 5% 1/16WR62 1-216-829-11 METAL CHIP 4.7K 5% 1/16W

R63 1-216-829-11 METAL CHIP 4.7K 5% 1/16W

MAIN


66

HCD-DX80

R64 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR65 1-216-809-11 METAL CHIP 100 5% 1/16WR66 1-216-833-11 METAL CHIP 10K 5% 1/16WR67 1-216-833-11 METAL CHIP 10K 5% 1/16W

R68 1-216-821-11 METAL CHIP 1K 5% 1/16WR69 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR101 1-216-821-11 METAL CHIP 1K 5% 1/16WR102 1-216-845-11 METAL CHIP 100K 5% 1/16WR103 1-216-833-11 METAL CHIP 10K 5% 1/16W


R109 1-216-833-11 METAL CHIP 10K 5% 1/16WR110 1-216-819-11 METAL CHIP 680 5% 1/16WR111 1-216-833-11 METAL CHIP 10K 5% 1/16WR112 1-216-841-11 METAL CHIP 47K 5% 1/16WR113 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

R114 1-216-845-11 METAL CHIP 100K 5% 1/16WR115 1-216-833-11 METAL CHIP 10K 5% 1/16WR116 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR117 1-216-833-11 METAL CHIP 10K 5% 1/16WR121 1-216-834-11 METAL CHIP 12K 5% 1/16W

R122 1-216-833-11 METAL CHIP 10K 5% 1/16WR123 1-216-833-11 METAL CHIP 10K 5% 1/16WR124 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR125 1-216-833-11 METAL CHIP 10K 5% 1/16WR132 1-216-809-11 METAL CHIP 100 5% 1/16W

R133 1-216-809-11 METAL CHIP 100 5% 1/16WR134 1-216-821-11 METAL CHIP 1K 5% 1/16WR135 1-216-839-11 METAL CHIP 33K 5% 1/16WR136 1-216-842-11 METAL CHIP 56K 5% 1/16W

(BR)R137 1-216-837-11 METAL CHIP 22K 5% 1/16W

R138 1-216-845-11 METAL CHIP 100K 5% 1/16W(BR)

R139 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR141 1-216-821-11 METAL CHIP 1K 5% 1/16WR142 1-216-822-11 METAL CHIP 1.2K 5% 1/16WR143 1-216-841-11 METAL CHIP 47K 5% 1/16W

R144 1-216-864-11 SHORT 0R145 1-216-821-11 METAL CHIP 1K 5% 1/16WR146 1-216-821-11 METAL CHIP 1K 5% 1/16WR147 1-216-821-11 METAL CHIP 1K 5% 1/16WR148 1-216-821-11 METAL CHIP 1K 5% 1/16W


R156 1-216-845-11 METAL CHIP 100K 5% 1/16WR157 1-216-849-11 METAL CHIP 220K 5% 1/16WR158 1-216-845-11 METAL CHIP 100K 5% 1/16WR159 1-216-833-11 METAL CHIP 10K 5% 1/16WR160 1-216-819-11 METAL CHIP 680 5% 1/16W

R161 1-216-833-11 METAL CHIP 10K 5% 1/16WR162 1-216-841-11 METAL CHIP 47K 5% 1/16W

R163 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR164 1-216-845-11 METAL CHIP 100K 5% 1/16WR165 1-216-833-11 METAL CHIP 10K 5% 1/16W

R166 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR171 1-216-834-11 METAL CHIP 12K 5% 1/16WR172 1-216-833-11 METAL CHIP 10K 5% 1/16WR173 1-216-833-11 METAL CHIP 10K 5% 1/16WR175 1-216-833-11 METAL CHIP 10K 5% 1/16W

R185 1-216-839-11 METAL CHIP 33K 5% 1/16WR187 1-216-837-11 METAL CHIP 22K 5% 1/16WR189 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR212 1-216-821-11 METAL CHIP 1K 5% 1/16WR217 1-216-809-11 METAL CHIP 100 5% 1/16W

R219 1-216-821-11 METAL CHIP 1K 5% 1/16WR224 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR226 1-216-851-11 METAL CHIP 330K 5% 1/16WR228 1-216-845-11 METAL CHIP 100K 5% 1/16WR301 1-216-836-11 METAL CHIP 18K 5% 1/16W

R302 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR303 1-216-809-11 METAL CHIP 100 5% 1/16WR304 1-216-809-11 METAL CHIP 100 5% 1/16WR305 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR306 1-216-832-11 METAL CHIP 8.2K 5% 1/16W

R307 1-216-832-11 METAL CHIP 8.2K 5% 1/16WR308 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR309 1-216-837-11 METAL CHIP 22K 5% 1/16WR311 1-216-857-11 METAL CHIP 1M 5% 1/16WR312 1-218-745-11 RES-CHIP 160K 5% 1/16W


R319 1-216-852-11 METAL CHIP 390K 5% 1/16WR320 1-216-822-11 METAL CHIP 1.2K 5% 1/16WR321 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR331 1-216-846-11 METAL CHIP 120K 5% 1/16WR332 1-216-809-11 METAL CHIP 100 5% 1/16W

R333 1-216-830-11 METAL CHIP 5.6K 5% 1/16WR334 1-218-332-11 RES-CHIP 130K 5% 1/16WR335 1-216-813-11 METAL CHIP 220 5% 1/16WR336 1-216-846-11 METAL CHIP 120K 5% 1/16WR337 1-216-813-11 METAL CHIP 220 5% 1/16W

R338 1-216-837-11 METAL CHIP 22K 5% 1/16WR339 1-216-834-11 METAL CHIP 12K 5% 1/16WR340 1-216-850-11 METAL CHIP 270K 5% 1/16WR341 1-216-813-11 METAL CHIP 220 5% 1/16WR342 1-216-834-11 METAL CHIP 12K 5% 1/16W

R343 1-219-787-17 FUSIBLE 5.6 5% 1/4WR344 1-219-787-17 FUSIBLE 5.6 5% 1/4WR345 1-216-836-11 METAL CHIP 18K 5% 1/16WR346 1-216-836-11 METAL CHIP 18K 5% 1/16WR347 1-216-830-11 METAL CHIP 5.6K 5% 1/16W

R351 1-216-836-11 METAL CHIP 18K 5% 1/16WR352 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR353 1-216-809-11 METAL CHIP 100 5% 1/16WR354 1-216-809-11 METAL CHIP 100 5% 1/16WR355 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

MAIN


67

HCD-DX80

R356 1-216-832-11 METAL CHIP 8.2K 5% 1/16WR357 1-216-832-11 METAL CHIP 8.2K 5% 1/16WR358 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR359 1-216-839-11 METAL CHIP 33K 5% 1/16WR360 1-216-819-11 METAL CHIP 680 5% 1/16W

R361 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR363 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR364 1-216-819-11 METAL CHIP 680 5% 1/16WR366 1-216-827-11 METAL CHIP 3.3K 5% 1/16WR367 1-216-841-11 METAL CHIP 47K 5% 1/16W

R368 1-216-827-11 METAL CHIP 3.3K 5% 1/16WR369 1-216-827-11 METAL CHIP 3.3K 5% 1/16WR371 1-216-841-11 METAL CHIP 47K 5% 1/16WR372 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR373 1-216-821-11 METAL CHIP 1K 5% 1/16W

R374 1-216-841-11 METAL CHIP 47K 5% 1/16WR375 1-218-296-11 RES-CHIP 75K 5% 1/16WR376 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR377 1-216-841-11 METAL CHIP 47K 5% 1/16WR378 1-218-296-11 RES-CHIP 75K 5% 1/16W

R379 1-216-821-11 METAL CHIP 1K 5% 1/16WR380 1-216-055-11 METAL CHIP 1.8K 5% 1/10WR381 1-216-846-11 METAL CHIP 120K 5% 1/16WR382 1-216-809-11 METAL CHIP 100 5% 1/16WR383 1-216-830-11 METAL CHIP 5.6K 5% 1/16W

R384 1-218-332-11 RES-CHIP 130K 5% 1/16WR386 1-216-846-11 METAL CHIP 120K 5% 1/16WR387 1-216-813-11 METAL CHIP 220 5% 1/16WR388 1-216-837-11 METAL CHIP 22K 5% 1/16WR389 1-216-834-11 METAL CHIP 12K 5% 1/16W

R390 1-216-850-11 METAL CHIP 270K 5% 1/16WR391 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR392 1-216-834-11 METAL CHIP 12K 5% 1/16WR393 1-216-837-11 METAL CHIP 22K 5% 1/16WR394 1-216-813-11 METAL CHIP 220 5% 1/16W

R396 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR397 1-216-821-11 METAL CHIP 1K 5% 1/16WR398 1-216-055-11 METAL CHIP 1.8K 5% 1/10WR399 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR500 1-216-829-11 METAL CHIP 4.7K 5% 1/16W


R508 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR509 1-216-833-11 METAL CHIP 10K 5% 1/16WR510 1-216-845-11 METAL CHIP 100K 5% 1/16WR511 1-216-851-11 METAL CHIP 330K 5% 1/16WR512 1-216-809-11 METAL CHIP 100 5% 1/16W

R513 1-216-864-11 SHORT 0R514 1-216-809-11 METAL CHIP 100 5% 1/16WR515 1-216-833-11 METAL CHIP 10K 5% 1/16WR516 1-216-833-11 METAL CHIP 10K 5% 1/16WR517 1-216-833-11 METAL CHIP 10K 5% 1/16W

R518 1-216-833-11 METAL CHIP 10K 5% 1/16WR519 1-216-809-11 METAL CHIP 100 5% 1/16W

R520 1-216-833-11 METAL CHIP 10K 5% 1/16WR522 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR523 1-216-829-11 METAL CHIP 4.7K 5% 1/16W

(EXCEPT SP)

R523 1-216-864-11 SHORT 0 (SP)R529 1-216-809-11 METAL CHIP 100 5% 1/16WR530 1-216-809-11 METAL CHIP 100 5% 1/16WR534 1-216-817-11 METAL CHIP 470 5% 1/16WR535 1-216-817-11 METAL CHIP 470 5% 1/16W

R537 1-216-817-11 METAL CHIP 470 5% 1/16WR540 1-216-809-11 METAL CHIP 100 5% 1/16WR541 1-216-841-11 METAL CHIP 47K 5% 1/16WR542 1-216-809-11 METAL CHIP 100 5% 1/16WR543 1-216-809-11 METAL CHIP 100 5% 1/16W

R544 1-216-809-11 METAL CHIP 100 5% 1/16WR545 1-216-809-11 METAL CHIP 100 5% 1/16WR546 1-216-809-11 METAL CHIP 100 5% 1/16WR547 1-216-809-11 METAL CHIP 100 5% 1/16WR548 1-216-809-11 METAL CHIP 100 5% 1/16W

R549 1-216-809-11 METAL CHIP 100 5% 1/16WR553 1-216-833-11 METAL CHIP 10K 5% 1/16WR556 1-216-809-11 METAL CHIP 100 5% 1/16WR557 1-216-809-11 METAL CHIP 100 5% 1/16WR570 1-216-809-11 METAL CHIP 100 5% 1/16W


R578 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR579 1-216-817-11 METAL CHIP 470 5% 1/16WR582 1-216-833-11 METAL CHIP 10K 5% 1/16WR583 1-216-809-11 METAL CHIP 100 5% 1/16WR584 1-216-809-11 METAL CHIP 100 5% 1/16W

R585 1-216-833-11 METAL CHIP 10K 5% 1/16WR588 1-216-817-11 METAL CHIP 470 5% 1/16WR589 1-216-809-11 METAL CHIP 100 5% 1/16WR590 1-216-809-11 METAL CHIP 100 5% 1/16WR591 1-216-809-11 METAL CHIP 100 5% 1/16W

R592 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR593 1-216-821-11 METAL CHIP 1K 5% 1/16W

(EXCEPT SP)R593 1-216-829-11 METAL CHIP 4.7K 5% 1/16W

(SP)R594 1-216-809-11 METAL CHIP 100 5% 1/16WR595 1-216-809-11 METAL CHIP 100 5% 1/16W



R755 1-216-821-11 METAL CHIP 1K 5% 1/16WR804 1-216-841-11 METAL CHIP 47K 5% 1/16W

MAIN


68

HCD-DX80

R820 1-216-821-11 METAL CHIP 1K 5% 1/16WR821 1-216-841-11 METAL CHIP 47K 5% 1/16WR822 1-216-842-11 METAL CHIP 56K 5% 1/16W

R823 1-216-833-11 METAL CHIP 10K 5% 1/16WR824 1-216-841-11 METAL CHIP 47K 5% 1/16WR825 1-216-827-11 METAL CHIP 3.3K 5% 1/16WR826 1-216-839-11 METAL CHIP 33K 5% 1/16WR827 1-216-837-11 METAL CHIP 22K 5% 1/16W

R829 1-216-837-11 METAL CHIP 22K 5% 1/16WR830 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR831 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR832 1-216-845-11 METAL CHIP 100K 5% 1/16WR841 1-216-837-11 METAL CHIP 22K 5% 1/16W

R842 1-216-837-11 METAL CHIP 22K 5% 1/16WR843 1-216-829-11 METAL CHIP 4.7K 5% 1/16WR844 1-216-845-11 METAL CHIP 100K 5% 1/16WR845 1-216-857-11 METAL CHIP 1M 5% 1/16WR854 1-216-841-11 METAL CHIP 47K 5% 1/16W


R866 1-216-806-11 RES-CHIP 56 5% 1/16W0R868 1-215-891-11 METAL OXIDE 680 5% 2W F0R869 1-215-891-11 METAL OXIDE 680 5% 2W F

R891 1-216-833-11 METAL CHIP 10K 5% 1/16WR892 1-216-829-11 METAL CHIP 4.7K 5% 1/16W

R893 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR895 1-216-864-11 SHORT 0R901 1-249-405-11 CARBON 100 5% 1/4WR911 1-216-826-11 METAL CHIP 2.7K 5% 1/16WR912 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

R914 1-216-825-11 METAL CHIP 2.2K 5% 1/16WR966 1-216-806-11 RES-CHIP 56 5% 1/16W

< COMPOSITION CIRCUIT BLOCK >

RB41 1-234-575-11 ENCAPSULATED COMPONENT(AM FRONT-END)


RV11 1-241-765-11 RES, ADJ, CARBON 22KRV301 1-241-764-11 RES, ADJ, CARBON 10KRV302 1-241-762-11 RES, ADJ, CARBON 2.2KRV303 1-241-762-11 RES, ADJ, CARBON 2.2KRV304 1-241-768-11 RES, ADJ, CARBON 220K

RV351 1-241-764-11 RES, ADJ, CARBON 10KRV354 1-241-768-11 RES, ADJ, CARBON 220K

< RELAY >

RY801 1-755-372-11 RELAY

< TRANSFORMER >

T11 1-435-792-11 TRANSFORMER, DISCRIMINATORT301 1-423-980-11 TRANSFORMER, BIAS OSCILLATION

< TERMINAL >

TM1 1-694-555-22 TERMINAL BOARD (4P) (ANTENNA)TM801 1-694-635-12 TERMINAL BOARD (4P) (SPEAKER)

< VIBRATOR >

X51 1-760-549-31 VIBRATOR, CRYSTAL (4.5MHz)X501 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)X502 1-781-107-21 VIBRATOR, CERAMIC (16MHz)

**************************************************************

1-680-265-11 MAIN TRANS BOARD*****************

1-533-233-11 HOLDER, FUSE

< CAPACITOR >

C941 1-128-553-11 ELECT 220uF 20% 63V

< CONNECTOR >

CN973 1-568-106-11 CONNECTOR 4PCN977 1-564-528-11 PLUG, CONNECTOR 13P

< DIODE >

D977 8-719-024-99 DIODE 11ES2-NTA2B

< FUSE >

0F971 1-532-506-31 FUSE, GLASS TUBE (T6.3AL/250V)(EXCEPT MX)

0F974 1-532-506-31 FUSE, GLASS TUBE (T6.3AL/250V)0F975 1-532-506-31 FUSE, GLASS TUBE (T6.3AL/250V)0F976 1-533-949-31 FUSE, GLASS TUBE (T8.0AL/250V)0F977 1-533-949-31 FUSE, GLASS TUBE (T8.0AL/250V)

< FUSIBLE >

0R941 1-217-673-81 FUSIBLE 1 5% 1/4W F0R944 1-217-641-81 FUSIBLE 4.7 5% 1/4W F0R951 1-219-120-11 FUSIBLE 0.15 5% 1/4W F0R952 1-219-120-11 FUSIBLE 0.15 5% 1/4W F0R953 1-219-120-11 FUSIBLE 0.15 5% 1/4W F

< TRANSFORMER >

0T910 1-437-355-11 POWER TRANSFORMER (EXCEPT BR)0T910 1-437-284-11 POWER TRANSFORMER (BR)**************************************************************

1-675-910-14 MOTOR BOARD*************

< CAPACITOR >

C721 1-162-306-11 CERAMIC 0.01uF 30% 16V

< CONNECTOR >

CN721 1-770-516-31 CONNECTOR, FFC 8PCN722 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P

< SWITCH >

S701 1-771-822-11 SWITCH, LEVER (SLIDE) (OPEN/CLOSE)**************************************************************


MAIN MAIN TRANS MOTOR


69

HCD-DX80

A-4475-778-A PAD SWITCH BOARD, COMPLETE (EXCEPT BR)

A-4476-896-A PAD SWITCH BOARD, COMPLETE (BR)***************************

< CAPACITOR >

C751 1-162-306-11 CERAMIC 0.01uF 30% 16VC752 1-162-306-11 CERAMIC 0.01uF 30% 16V

< LED >

D751 8-719-063-93 LED SLR325VC-N-T32 (REC PAUSE/START)D752 8-719-063-93 LED SLR325VC-N-T32 (ENTER)

< TRANSISTOR >

Q751 8-729-900-80 TRANSISTOR BA1A4M-TPQ752 8-729-900-80 TRANSISTOR BA1A4M-TP

< RESISTOR >

R750 1-249-410-11 CARBON 270 5% 1/4WR751 1-249-827-11 CARBON 680 5% 1/4WR752 1-249-411-11 CARBON 330 5% 1/4WR754 1-249-410-11 CARBON 270 5% 1/4WR755 1-249-413-11 CARBON 470 5% 1/4W

R756 1-249-414-11 CARBON 560 5% 1/4WR757 1-249-416-11 CARBON 820 5% 1/4WR758 1-249-417-11 CARBON 1K 5% 1/4WR759 1-249-418-11 CARBON 1.2K 5% 1/4WR760 1-249-419-11 CARBON 1.5K 5% 1/4W

R761 1-249-421-11 CARBON 2.2K 5% 1/4WR762 1-249-422-11 CARBON 2.7K 5% 1/4WR763 1-249-424-11 CARBON 3.9K 5% 1/4WR764 1-249-426-11 CARBON 5.6K 5% 1/4WR765 1-249-428-11 CARBON 8.2K 5% 1/4W

R766 1-249-431-11 CARBON 15K 5% 1/4WR768 1-249-410-11 CARBON 270 5% 1/4WR769 1-249-413-11 CARBON 470 5% 1/4WR770 1-249-414-11 CARBON 560 5% 1/4WR771 1-249-416-11 CARBON 820 5% 1/4W

R772 1-249-417-11 CARBON 1K 5% 1/4WR773 1-249-418-11 CARBON 1.2K 5% 1/4WR774 1-249-419-11 CARBON 1.5K 5% 1/4WR775 1-249-421-11 CARBON 2.2K 5% 1/4WR776 1-249-422-11 CARBON 2.7K 5% 1/4W

R777 1-249-424-11 CARBON 3.9K 5% 1/4WR778 1-249-426-11 CARBON 5.6K 5% 1/4WR779 1-249-428-11 CARBON 8.2K 5% 1/4WR780 1-249-431-11 CARBON 15K 5% 1/4WR790 1-249-434-11 CARBON 27K 5% 1/4W

< SWITCH >

S751 1-476-504-11 ENCODER, ROTARY (VOLUME)S752 1-771-410-21 SWITCH, TACTILE (DISPLAY)S753 1-771-410-21 SWITCH, TACTILE (B)S754 1-771-410-21 SWITCH, TACTILE (b)S755 1-771-410-21 SWITCH, TACTILE (SPECTRUM)

S756 1-771-410-21 SWITCH, TACTILE (EFECT ON/OFF)S757 1-771-410-21 SWITCH, TACTILE (GAME EQ)

S758 1-771-410-21 SWITCH, TACTILE (KARAOKE PON)S760 1-771-410-21 SWITCH, TACTILE (m -)S761 1-771-410-21 SWITCH, TACTILE (.)

S762 1-771-410-21 SWITCH, TACTILE (x)S763 1-771-410-21 SWITCH, TACTILE (CD SYNC HI-DUB)S764 1-771-410-21 SWITCH, TACTILE (REC PAUSE/START)S765 1-771-410-21 SWITCH, TACTILE (M +)S768 1-771-410-21 SWITCH, TACTILE (PLAY MODE)

S769 1-771-410-21 SWITCH, TACTILE (REPEAT)S770 1-771-410-21 SWITCH, TACTILE (EDIT)S771 1-771-410-21 SWITCH, TACTILE (MUSIC EQ)S772 1-771-410-21 SWITCH, TACTILE (MOVIE EQ)S773 1-771-410-21 SWITCH, TACTILE (v)

S774 1-771-410-21 SWITCH, TACTILE (ENTER)S775 1-771-410-21 SWITCH, TACTILE (V)S776 1-771-410-21 SWITCH, TACTILE (P FILE)S777 1-771-410-21 SWITCH, TACTILE (GROOVE)S778 1-771-410-21 SWITCH, TACTILE (SURROUND)

S779 1-771-410-21 SWITCH, TACTILE (g G)S780 1-771-410-21 SWITCH, TACTILE (X)S781 1-771-410-21 SWITCH, TACTILE (>)

**************************************************************

A-4476-112-A PANEL BOARD, COMPLETE (EXCEPT BR)A-4726-068-A PANEL BOARD, COMPLETE (BR)

**********************

4-231-581-01 HOLDER (FL)

< CAPACITOR >

C604 1-124-257-00 ELECT 2.2uF 20% 50VC606 1-124-257-00 ELECT 2.2uF 20% 50VC607 1-126-157-11 ELECT 10uF 20% 16VC608 1-126-157-11 ELECT 10uF 20% 16VC609 1-162-303-11 CERAMIC 0.0033uF 30% 16V

C610 1-126-157-11 ELECT 10uF 20% 16VC611 1-126-157-11 ELECT 10uF 20% 16VC612 1-162-306-11 CERAMIC 0.01uF 30% 16VC613 1-124-261-00 ELECT 10uF 20% 50VC614 1-162-294-31 CERAMIC 0.001uF 10% 50V

C615 1-104-664-11 ELECT 47uF 20% 10VC616 1-126-934-11 ELECT 200uF 20% 16VC617 1-124-589-11 ELECT 47uF 20% 16VC618 1-162-306-11 CERAMIC 0.01uF 30% 16VC619 1-124-589-11 ELECT 47uF 20% 16V

C620 1-162-306-11 CERAMIC 0.01uF 30% 16VC622 1-126-163-11 ELECT 4.7uF 20% 50VC623 1-164-159-11 CERAMIC 0.1uF 50VC624 1-162-306-11 CERAMIC 0.01uF 30% 16VC625 1-162-306-11 CERAMIC 0.01uF 30% 16V

C626 1-162-306-11 CERAMIC 0.01uF 30% 16VC627 1-162-306-11 CERAMIC 0.01uF 30% 16VC628 1-162-306-11 CERAMIC 0.01uF 30% 16VC629 1-162-306-11 CERAMIC 0.01uF 30% 16VC630 1-162-294-31 CERAMIC 0.001uF 10% 50V

C631 1-162-294-31 CERAMIC 0.001uF 10% 50VC651 1-164-159-11 CERAMIC 0.1uF 50VC652 1-126-964-11 ELECT 10uF 20% 50VC653 1-126-964-11 ELECT 10uF 20% 50V

PAD SWITCH PANEL


70

HCD-DX80

C717 1-124-584-00 ELECT 100uF 20% 10V

C718 1-124-584-00 ELECT 100uF 20% 10VC719 1-124-257-00 ELECT 2.2uF 20% 50VC736 1-124-261-00 ELECT 10uF 20% 50VC737 1-124-261-00 ELECT 10uF 20% 50VC738 1-124-257-00 ELECT 2.2uF 20% 50V

C739 1-162-215-31 CERAMIC 47PF 5% 50VC740 1-162-282-31 CERAMIC 100PF 10% 50VC741 1-124-463-00 ELECT 0.1uF 20% 50VC742 1-162-215-31 CERAMIC 47PF 5% 50VC743 1-162-290-31 CERAMIC 470PF 10% 50V

C744 1-162-294-31 CERAMIC 0.001uF 10% 50VC747 1-126-961-11 ELECT 2.2uF 20% 50VC748 1-162-306-11 CERAMIC 0.01uF 30% 16VC749 1-164-159-11 CERAMIC 0.1uF 50V

(EXCEPT BR)

< CONNECTOR >

CN601 1-793-767-11 CONNECTOR, BOARD TO BOARD 30PCNS601 1-770-401-11 HOUSING, CONNECTOR (PC BOARD) 8P

< DIODE >

D608 8-719-084-40 LED SEL5955A-TP15 (GAME)D609 8-719-084-40 LED SEL5955A-TP15 (TUNER/BAND)D610 8-719-109-85 DIODE MTZJ-T-72-5.1BD611 8-719-911-19 DIODE 1SS133T-72D612 8-719-084-40 LED SEL5955A-TP15 (TUNER/BAND)

D613 8-719-084-40 LED SEL5955A-TP15 (CD)D614 8-719-084-40 LED SEL5955A-TP15 (CD)D615 8-719-084-40 LED SEL5955A-TP15 (TAPE A/B)D616 8-719-084-40 LED SEL5955A-TP15 (TAPE A/B)D617 8-719-084-40 LED SEL5955A-TP15 (MD (VIDEO))

D618 8-719-084-40 LED SEL5955A-TP15 (MD (VIDEO))D619 8-719-947-53 DIODE MTZJ-T-72-12BD620 8-719-947-53 DIODE MTZJ-T-72-12B

< FLUORESCENT INDICATOR TUBE >

FL601 1-518-739-11 INDICATOR TUBE, FLUORESCENT

< IC >

IC601 8-759-828-89 IC MB90M407PF-G-103-BNDIC602 8-759-570-21 IC BA3830F-E2IC603 8-759-827-70 IC NJL64H400A-1IC616 8-759-647-10 IC uPC2933HFIC722 8-759-167-88 IC NJM4565D

< JACK >

J601 1-793-724-11 JACK BLOCK, PIN 3P (GAME INPUT)J631 1-785-569-11 JACK (SMALL TYPE) (PHONES)J722 1-785-569-11 JACK (SMALL TYPE) (MIC)

< TRANSISTOR >

Q601 8-729-900-80 TRANSISTOR BA1A4M-TPQ602 8-729-900-80 TRANSISTOR BA1A4M-TPQ603 8-729-900-80 TRANSISTOR BA1A4M-TPQ604 8-729-900-80 TRANSISTOR BA1A4M-TPQ605 8-729-900-80 TRANSISTOR BA1A4M-TP

Q721 8-729-119-79 TRANSISTOR 2SC2785TP-FEK

< RESISTOR >

R602 1-249-417-11 CARBON 1K 5% 1/4WR603 1-249-417-11 CARBON 1K 5% 1/4WR604 1-249-441-11 CARBON 100K 5% 1/4WR605 1-249-441-11 CARBON 100K 5% 1/4WR606 1-247-889-00 CARBON 270K 5% 1/4W

R607 1-247-889-00 CARBON 270K 5% 1/4WR608 1-249-421-11 CARBON 2.2K 5% 1/4WR609 1-249-440-11 CARBON 82K 5% 1/4WR610 1-249-441-11 CARBON 100K 5% 1/4WR611 1-249-437-11 CARBON 47K 5% 1/4W


R617 1-249-439-11 CARBON 68K 5% 1/4WR618 1-249-429-11 CARBON 10K 5% 1/4WR625 1-249-401-11 CARBON 47 5% 1/4WR626 1-249-811-11 CARBON 150 5% 1/4WR627 1-249-805-11 CARBON 82 5% 1/4W

R628 1-249-811-11 CARBON 150 5% 1/4WR629 1-249-811-11 CARBON 150 5% 1/4WR630 1-249-409-11 CARBON 220 5% 1/4WR631 1-249-418-11 CARBON 1.2K 5% 1/4WR632 1-249-417-11 CARBON 1K 5% 1/4W

R633 1-249-416-11 CARBON 820 5% 1/4WR634 1-249-414-11 CARBON 560 5% 1/4WR635 1-249-413-11 CARBON 470 5% 1/4WR636 1-249-410-11 CARBON 270 5% 1/4WR645 1-249-429-11 CARBON 10K 5% 1/4W

R646 1-247-807-31 CARBON 100 5% 1/4WR647 1-247-807-31 CARBON 100 5% 1/4WR650 1-249-429-11 CARBON 10K 5% 1/4WR651 1-247-807-31 CARBON 100 5% 1/4WR652 1-249-429-11 CARBON 10K 5% 1/4W

R653 1-249-429-11 CARBON 10K 5% 1/4WR654 1-249-417-11 CARBON 1K 5% 1/4WR655 1-247-807-31 CARBON 100 5% 1/4WR656 1-247-807-31 CARBON 100 5% 1/4WR657 1-249-429-11 CARBON 10K 5% 1/4W

R658 1-249-429-11 CARBON 10K 5% 1/4WR659 1-249-429-11 CARBON 10K 5% 1/4WR660 1-247-903-00 CARBON 1M 5% 1/4WR661 1-249-429-11 CARBON 10K 5% 1/4WR662 1-249-429-11 CARBON 10K 5% 1/4W

R663 1-249-429-11 CARBON 10K 5% 1/4WR680 1-249-411-11 CARBON 330 5% 1/4WR681 1-247-843-11 CARBON 3.3K 5% 1/4WR682 1-249-434-11 CARBON 27K 5% 1/4WR690 1-249-417-11 CARBON 1K 5% 1/4W


PANEL


71

HCD-DX80


R722 1-249-430-11 CARBON 12K 5% 1/4WR734 1-247-807-31 CARBON 100 5% 1/4WR735 1-247-885-00 CARBON 180K 5% 1/4WR736 1-249-429-11 CARBON 10K 5% 1/4WR737 1-249-433-11 CARBON 22K 5% 1/4W


R745 1-247-807-31 CARBON 100 5% 1/4WR746 1-249-417-11 CARBON 1K 5% 1/4WR748 1-249-441-11 CARBON 100K 5% 1/4WR802 1-249-441-11 CARBON 100K 5% 1/4WR803 1-249-441-11 CARBON 100K 5% 1/4W


R809 1-249-441-11 CARBON 100K 5% 1/4WR810 1-249-441-11 CARBON 100K 5% 1/4WR811 1-249-417-11 CARBON 1K 5% 1/4WR812 1-249-417-11 CARBON 1K 5% 1/4W


RV722 1-227-360-11 RES, VAR, CARBON 50K (MIC LEVEL)

< SWITCH >

S601 1-771-410-21 SWITCH, TACTILE (MD (VIDEO))S602 1-771-410-21 SWITCH, TACTILE (TAPE A/B)S603 1-771-410-21 SWITCH, TACTILE (CD)S604 1-771-410-21 SWITCH, TACTILE (TUNER/BAND)S605 1-771-410-21 SWITCH, TACTILE (GAME)

S606 1-771-410-21 SWITCH, TACTILE(SURROUND SPEAKER MODE)

< VIBRATOR >

X601 1-577-358-21 VIBRATOR, CERAMIC (4MHz)**************************************************************

A-4476-270-A POWER AMPLIFIER BOARD, COMPLETE (MX)A-4476-767-A POWER AMPLIFIER BOARD, COMPLETE

(E2, E51, AR)A-4476-770-A POWER AMPLIFIER BOARD, COMPLETE (SP)A-4726-062-A POWER AMPLIFIER BOARD, COMPLETE (BR)

*********************************

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

< CAPACITOR >

C501 1-126-963-11 ELECT 4.7uF 20% 50VC502 1-162-286-31 CERAMIC 220PF 10% 50VC503 1-162-281-21 CERAMIC 100PF 10% 50V

C504 1-104-665-11 ELECT 100uF 20% 10VC507 1-136-495-11 FILM 0.068uF 5% 50V

C508 1-136-495-11 FILM 0.068uF 5% 50VC509 1-128-560-11 ELECT 22uF 20% 100VC512 1-162-300-21 CERAMIC 0.01uF 50VC514 1-162-300-21 CERAMIC 0.01uF 50VC541 1-136-165-00 FILM 0.1uF 5% 50V

C542 1-137-838-11 ELECT 2200uF 20% 42V (EXCEPT SP)

C542 1-137-844-11 ELECT 2200uF 20% 42V(SP)

C544 1-137-749-11 MYLAR 0.1uF 100VC545 1-137-749-11 MYLAR 0.1uF 100VC546 1-137-843-11 ELECT 2200uF 20% 100V

(EXCEPT SP)

C546 1-137-849-11 ELECT 2200uF 20% 100V(SP)

C551 1-126-963-11 ELECT 4.7uF 20% 50VC552 1-162-286-31 CERAMIC 220PF 10% 50VC553 1-162-281-21 CERAMIC 100PF 10% 50VC554 1-104-665-11 ELECT 100uF 20% 10V

C557 1-136-495-11 FILM 0.068uF 5% 50VC558 1-136-495-11 FILM 0.068uF 5% 50VC559 1-128-560-11 ELECT 22uF 20% 100VC581 1-126-967-91 ELECT 47uF 20% 50VC591 1-136-165-00 FILM 0.1uF 5% 50V


C592 1-137-844-11 ELECT 2200uF 20% 42V(SP)


C596 1-137-849-11 ELECT 2200uF 20% 100V(SP)

C942 1-126-964-11 ELECT 10uF 20% 50V

C943 1-126-968-11 ELECT 100uF 20% 50V

< CONNECTOR >

CN502 1-778-981-21 CONNECTOR, BOARD TO BOARD 13PCN503 1-778-981-21 CONNECTOR, BOARD TO BOARD 13PCN504 1-506-468-11 PIN, CONNECTOR 3P

< DIODE >

D501 8-719-911-19 DIODE 1SS133T-72D502 8-719-911-19 DIODE 1SS133T-72D503 8-719-947-70 DIODE MTZJ-T-72-18CD504 8-719-947-70 DIODE MTZJ-T-72-18CD541 8-719-500-60 DIODE D5SBA20

D543 8-719-510-68 DIODE D5SBA204101D551 8-719-911-19 DIODE 1SS133T-72D581 8-719-911-19 DIODE 1SS133T-72D941 8-719-150-92 DIODE MTZJ-T-72-33D

< EARTH TERMINAL >

* EP501 1-537-738-21 TERMINAL, EARTH* EP502 1-537-738-21 TERMINAL, EARTH

PANEL POWER AMPLIFIER


72

HCD-DX80

< IC >

IC501 8-749-017-06 IC STK412-150

< TRANSISTOR >

Q501 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEAQ503 8-729-140-82 TRANSISTOR 2SA988TP-PAFAEAQ504 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEAQ505 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEAQ506 8-729-119-79 TRANSISTOR 2SC2785TP-FEK

Q551 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEAQ581 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEAQ831 8-729-119-79 TRANSISTOR 2SC2785TP-FEKQ941 8-729-141-83 TRANSISTOR 2SB1375

< RESISTOR >

R501 1-249-417-11 CARBON 1K 5% 1/4WR502 1-249-438-11 CARBON 56K 5% 1/4WR503 1-249-411-11 CARBON 330 5% 1/4WR504 1-249-438-11 CARBON 56K 5% 1/4WR505 1-249-417-11 CARBON 1K 5% 1/4W

R506 1-249-433-11 CARBON 22K 5% 1/4WR507 1-249-441-11 CARBON 100K 5% 1/4W

0R508 1-208-603-11 METAL 0.1 20% 5W FR509 1-260-076-11 CARBON 10 5% 1/2W

0R510 1-208-603-11 METAL 0.1 20% 5W F

0R511 1-212-881-11 FUSIBLE 100 5% 1/4W F0R512 1-202-972-61 FUSIBLE 1 5% 1/4W F

R513 1-249-435-11 CARBON 33K 5% 1/4WR514 1-249-421-11 CARBON 2.2K 5% 1/4WR515 1-249-433-11 CARBON 22K 5% 1/4W

R516 1-249-429-11 CARBON 10K 5% 1/4WR517 1-249-421-11 CARBON 2.2K 5% 1/4WR518 1-249-435-11 CARBON 33K 5% 1/4WR519 1-249-439-11 CARBON 68K 5% 1/4W

0R520 1-215-872-11 METAL OXIDE 3.3K 5% 1W F

R521 1-249-441-11 CARBON 100K 5% 1/4WR522 1-249-441-11 CARBON 100K 5% 1/4WR523 1-249-440-11 CARBON 82K 5% 1/4W

0R524 1-215-872-11 METAL OXIDE 3.3K 5% 1W FR531 1-249-409-11 CARBON 220 5% 1/4W


R552 1-249-438-11 CARBON 56K 5% 1/4WR553 1-249-411-11 CARBON 330 5% 1/4WR554 1-249-438-11 CARBON 56K 5% 1/4WR555 1-249-417-11 CARBON 1K 5% 1/4WR556 1-249-433-11 CARBON 22K 5% 1/4W

R557 1-249-441-11 CARBON 100K 5% 1/4W0R558 1-208-603-11 METAL 0.1 20% 5W F

R559 1-260-076-11 CARBON 10 5% 1/2W0R560 1-208-603-11 METAL 0.1 20% 5W F0R561 1-212-881-11 FUSIBLE 100 5% 1/4W F


R591 1-249-441-11 CARBON 100K 5% 1/4WR592 1-249-441-11 CARBON 100K 5% 1/4WR942 1-249-853-11 CARBON 8.2K 5% 1/4W

R943 1-249-417-11 CARBON 1K 5% 1/4WR945 1-247-853-11 CARBON 8.2K 5% 1/4W

**************************************************************

1-681-143-11 SENSOR BOARD**************

< CONNECTOR >

CN701 1-568-951-11 PIN, CONNECTOR 2P

< THERMISTOR >

TH701 1-807-796-11 THERMISTOR**************************************************************

A-2007-964-A SUB TRANS BOARD, COMPLETE (MX)A-4476-114-A SUB TRANS BOARD, COMPLETE

(E2, E51, SP, AR)A-4726-060-A SUB TRANS BOARD, COMPLETE (BR)

***************************

< CAPACITOR >

C971 1-113-925-11 CERAMIC 0.01uF 20% 250VC972 1-113-925-11 CERAMIC 0.01uF 20% 250VC973 1-126-933-11 ELECT 100uF 20% 16VC975 1-126-768-11 ELECT 2200uF 20% 16VC976 1-164-159-11 CERAMIC 0.1uF 50V

C977 1-164-159-11 CERAMIC 0.1uF 50VC978 1-164-159-11 CERAMIC 0.1uF 50V

< CONNECTOR >

* CN972 1-564-321-21 PIN, CONNECTOR 2P* CN974 1-568-226-11 PIN, CONNECTOR 2P

< DIODE >

D971 8-719-911-19 DIODE 1SS133T-72D972 8-719-024-99 DIODE 11ES2-NTA2BD973 8-719-024-99 DIODE 11ES2-NTA2BD974 8-719-024-99 DIODE 11ES2-NTA2BD975 8-719-024-99 DIODE 11ES2-NTA2B

< IC >

IC971 8-759-158-62 IC TA78057S

< TRANSISTOR >

Q971 8-729-119-79 TRANSISTOR 2SC2785TP-FEK

< RESISTOR >


< RELAY >

0RY971 1-755-276-11 RELAY, POWER0RY972 1-755-276-11 RELAY, POWER


POWER AMPLIFIER SENSOR SUB TRANS


73

HCD-DX80

< SWITCH >

0S901 1-786-055-11 SELECTOR, VOLTAGE(VOLTAGE SELECTOR) (EXCEPT MX)

< TRANSFORMER >

0T972 1-437-331-21 POWER TRANSFORMER**************************************************************

1-680-692-11 VIDEO SWITCH BOARD*******************

< CONNECTOR >

CN607 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P

< JACK >

J401 1-774-227-11 JACK, PIN 1P (VIDEO OUT)

< JUMPER RESISTOR >

JR781 1-216-864-11 SHORT 0************************************************************

MISCELLANEOUS**************

101 1-773-045-11 WIRE (FLAT TYPE) (17 CORE)104 1-757-418-11 WIRE (FLAT TYPE) (21 CORE) (AR)104 1-757-683-11 CABLE, FLAT (21 CORE) (EXCEPT AR)

0108 1-757-813-21 CORD, POWER (BR)0108 1-777-071-51 CORD, POWER (EXCEPT BR)

509 1-791-983-12 WIRE (FLAT TYPE) (8 CORE)556 1-757-710-11 WIRE (FLAT TYPE) (16 CORE)HP901 A-2004-771-A BASE (A) ASSY, HEADHRP901 A-2004-772-A BASE (B) ASSY, HEADM721 A-4672-826-A MOTOR ASSY

M901 X-3378-241-1 MOTOR ASSY (CAPSTAN)M961 1-763-072-11 FAN, D.C.PM901 1-454-887-32 SOLENOID, PLUNGERPM901 1-454-887-32 SOLENOID, PLUNGER

0T910 1-437-284-11 TRANSFORMER, POWER (BR)

0T910 1-437-355-11 POWER TRANSFOMER (EXCEPT BR)************************************************************

**************HARDWARE LIST**************

#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S#2 7-685-103-19 + PTPWH (2X5)#3 7-685-650-79 SCREW +BVTP 3X16 TYPE2 N-S#4 7-685-881-09 SCREW +BVTT 4X8 (S)#5 7-627-853-28 SCREW, PRECISION +P 2X3 TYPE3

#6 7-628-254-05 SCREW +PS 2.6X5#7 7-623-921-01 RING, RETAINING, CAPSTAN

************************************************************

ACCESSORIES & PACKING MATERIALS*******************************1-569-008-21 ADAPTOR, CONVERSION 2P (EXCEPT BR)1-793-184-21 CONNECTOR (F TYPE ADAPTOR) (EXCEPT BR)

SUB TRANS


HCD-DX80

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.

Ver. Date Description of Revision

1.1 2001.11 Addition of Ref. No. 530 for chassis (SPM-01044)

1.0 2001.03 New

manual de srvicio HCD-DX80.pdf

Documents

Transcript of manual de srvicio HCD-DX80.pdf