Manual cb1 y cb400sf en ingles.doc

CHARACTERISTICS

Attention : In the given manual are described the following Updatings of motorcycles Honda: СВ400 Super Four:

CB400N,CB400R,CB400Flls,CB400FIIT,CB400FIIV,CB400FIIIS,CB400FIIIT,CB400FIIIV.

CB400F (CB1):CB400FK

CB400FL

CB400FM.Attention: Removal and disassembly of units and Units It is carried out by way of numbers, Specified on Figures.Assembly and installation are carried out in the order, The opposite to disassembly and removal.

Identification

CB400N

Number on a seat (CB400N).

Number of the engine (CB400F).

Number of the engine (CB400N).

Number on a frame (CB400F).Number on a frame (CB400N). Number on a seat (CB400F).

4 Characteristics

Motor Oil1. Use oil on classification API – Not below SE (SE, SF, SG).2. Viscosity (SAE) Select according to the diagram. The temperature range, operation corresponding to conditions before the following replacement of oil.

Recommended viscosity of motor oil.

Characteristics

Honda CB400 Super Four Honda NC31 CB400N Super FourLength...............................................................2085 ммWidth...................................................................735 ммHeight................................................................1080 ммBase...................................................................1455ммWeight:

On a forward wheel............................................93 KgOn a back wheel.................................................99 KgFull...................................................................192 Kg

Full Weight:On a forward wheel..........................................114 KgOn a back wheel..............................................188 KgFull...................................................................302 Kg

Кастер................................................................27°15'Width of a trace...................................................109 ммBrake way (From 50 км/hr).....................................14 мRadius of a turn......................................................2,6 мHonda NC31 CB400FIIILength…………………………………………… 2080 mmWidth …………………………………………….. 720 mmHeight ……………………………………………1125 mm

Base …………………………………………….1450ммWeight:

On a forward wheel ......................................... 95 kgOn a back wheel ............................................. 100 kgFull .................................................................. 195 kgWeight full:On a forward wheel ......................................... 116 kgOn a back wheel ............................................. 189 kgFull .................................................................. 305 kg

The EngineUpdating.............................................................NC23EType ...............................………. 4-тактный, 4-cylinderWorking volume.................................................399 см3

ГРМ..................................…...DOHC, with a chain driveDiameter of the cylinder…………………………55,0 ммPiston stroke......................................................42,0 ммCompression ratio....................................................11,3Capacity................................…53 H.p. at11000 rev/minTorque..................................…37 Им at 10000 rev/minCooling system..........................................………LiquidLubricating system Refueling capacities:

The dry engine...................................................3,6 лWith replacement of the filter..............................2,9 лWithout replacement of the filter.........................2,7 л

Type of the oil pump.................................трохоидныйPressure (at 7000 rev/min).................................5 Kg/см2

Backlashes in rotors of the oil pump:Radial (between ledges of rotors)..................0,10 ммRadial (between a conducted rotor and the case............................................................0,15 - 0,22 ммFace.....................................................0,02- 0,07 мм

Cooling systemRefueling capacities:

In total.................................................................1,6 лрасширительный a tank.................................0,63 л

Pressure of opening of the valve of a cover of a radiator................................................................1,1 -1,4 Kg/см2

The temperature started openingтермостата.................................................80 - 84°СTemperature of full openingтермостата........................................................95°СHeight of rise of the valve термостата................8 ммSystem of submission of fuel (CB400N)

Fuel tank..............................................................18 лCarburetor.....................................Type CVx4 (VP22)Designation......................................................VP22AThrottle..........................................................30,5 ммIdling jet..............................................................2 1/2Level of fuel in поплавковой to the chamber..13,7мм Main jet:Carburettors № 1 and № 4.................................№95Carburettors № 2 and № 3.................................№98Idling jet..............................................................№35

Frequency of rotationIdling..................................................1200±100 rev/minSystem of submission of fuel (CB400FIII)

Fuel Tank.............................................................18 лThe carburettor .............................. Type CVx4 (VP02A)Designation .......................................…………... VP02AThrottle ..............................................………... 30,5 mmLevel of fuel in поплавковой to the chamber.. 13,7 mmThe screw of quality ..........................…………….. 23/4The main jet ......................................…………….№ 98Jet of idling ........................................…………….№ 35Frequency of rotationIdling ................................................. 1200ё100 rev/min

Characteristics 5

Ignition SystemType …………………………… Transistor батарейнаяSpark plugs:Standard:NGK ........................................................ CR8EH9Denso ..................................................... U24FER-9"Cold":NGK. ....................................................... CR9EH9Denso ..................................................... U27FER-9Backlash .................................................. 0,8-0,9 mmCorner of an advancing of ignition(at 1200ё100 rev/min) ........................14°до ВМТThe coil of ignition:Primary winding ........................................ 2 - 4 OhmSecondary winding:With tips ................................................... 23-27 whomWithout tips .............................................. 13-17 whomThe breaker:Resistance ............................................... 450-550 OhmPressure(Voltage) of a signal ................. More than 0,7 In

Start SystemLength of starter brushes:

Nominal..........................................................12,5 ммLimiting.............................................................8,5 ммThe head of cylinder block Thermal backlashes in valves:Admission .............................................. 0,12-0,18 mmRelease ................................................. 0,17-0,23 mmPressure of the end of a step of compression(at 400 rev/min) ....................................... 11-15 barPhases газораспределения:The inlet valve:Opening ................................................... 5°до ВМТClosing ................................................ 35 ° after НМТThe final valve:Opening ............................................... 35 ° up to НМТClosing .................................................. 5 ° after ВМТPressure of the end of a step of compression(at 400 rev/min) ....................................... 11-15 bar

Height of cams of camshafts (1):Nominal ......................................32,180-32,420 mmLimiting ....................................................32,130 mmDiameter basic шеек (2):Nominal ………………………….22,959 - 22,980 mmLimiting .................................................. 22,950 mmBacklash in the bearing distributiveShaft ............................................ 0,020 - 0,062 mmDiameter of a core of the valve: inlet:Nominal .......................................... 3,775-3,790 mmLimiting .................................................... 3,700 mm

Final:Nominal .......................................... 3,765 - 3,780 mmLimiting ........................................... 3,700 mmInternal diameter of the directing cartridge:Nominal .......................................... 3,800-3,812 mmLimiting ........................................... 3,890 mmBacklash between the cartridge and a core of the valve:Inlet:Nominal .......................................... 0,010 - 0,037 mmLimiting ........................................... 0,04 mmFinal:Nominal .......................................... 0,020-0,047 mmLimiting ........................................... 0,05 mmHeight выступания the directing cartridge (h):Inlet ................................................. 15,56-15,58 mmFinal ................................................ 13,21 - 13,23 mm

Height of a spring of the valve:Nominal .................................................... 40,03 mmLimiting ..................................................... 38,50 mmDiameter of a pusher of the valve:Nominal ..................................... 22,478 - 22,493 mmLimiting ..................................................... 22,470 mm

The piston and the cylinderDiameter of the cylinder:Nominal ..................................... 55,000 - 55,015 mmLimiting ...................................................... 55,10 mmDiameter of the piston:Nominal ..................................... 54,970 - 54,990 mmLimiting .................................................... 54,900 mmBacklash between the cylinder and the piston:Nominal .......................................... 0,010-0,045 mmLimiting ...................................................... 0,100 mmDiameter of an aperture under a piston finger:Nominal ...................................... 14,002-14,008 mmLimiting .................................................... 14,050 mmDiameter of a piston fingerNominal ...................................... 13,994-14,000 mmLimiting .................................................... 13,980 mmBacklash between a finger and the piston:Nominal ........................................ 0,002 - 0,014 mmLimiting ........................................................ 0,04 mmInternal diameter of the piston head of a rod:Nominal ...................................... 14,016-14,034 mmLimiting .................................................... 14,070 mmBacklash between a finger and a rod:Nominal .......................................... 0,016-0,040 mmLimiting ...................................................... 0,060

mmBacklash between a flute and the piston: компрессионноеRing ..................................................0,015-0,050 mmLimiting .......................................................... 0,10мм

6 Characteristics

Backlash in the lock:Top компрессионное Ring:Nominal ............................................ 0,18 - 0,28 mmLimiting ......................................................... 0,5 mmBottom компрессионное a ring:Nominal .............................................. 0,18-0,33 mmLimiting .......................................................... 0,5 mmмаслосъемное a ring:Nominal .............................................. 0,20-0,70 mmLimiting .......................................................... 1,1 mm

Crank ShaftAxial backlash:Nominal ............................................ 0,05 - 0,20 mmLimiting ........................................................ 0,30 mmBacklash in bearings:шатунный the bearing:Nominal ........................................ 0,028 - 0,052 mmLimiting ........................................................ 0,06 mmThe radical bearing:Nominal ........................................ 0,014 - 0,038 mmLimiting ........................................................ 0,05 mm

CouplingFree course of the leverCouplings ................................................. 10 - 20 mmThickness of a disk: nominal:"А". ...................................................... 3,22 - 3,38 mm"В". ...................................................... 3,22 - 3,38 mm"С" ...................................................... 3,42 - 3,58 mmLimiting:"А". ........................................................... 2,90 mm"В". ........................................................... 2,90 mm"С" ............................................................ 3,10 mmHeight of springs:Nominal .................................................... 45,6 mmLimiting ..................................................... 41,7 mmDiameter of the basic cartridge: internal:Nominal ....................................... 21,980 - 21,993 mmLimiting ..................................................... 22,030 mmExternal:Nominal ........................................29,993 - 30,007 mmLimiting.. ................................................... 29,960 mmInternal diameter of an asterisk of a drive маслянокго the pump:Nominal ....................................... 30,025-30,075 mmLimiting ..................................................... 30,150 mm

External diameter of a primary shaft (under the basic cartridge):Nominal ..................................... 21,967 - 21,980 mmLimiting ................................................... 21,950 mm

Transfer boxTransfer numbers of transfers:Forward transfer ....................................... 2,171CHECK POINT:1-st transfer .............................................. 3,3072-nd transfer ............................................. 2,2943-rd transfer .............................................. 1,7504-th transfer .............................................. 1,4285-th transfer..:. .......................................... 1,2406-th transfer .............................................. 1,130The main transfer:Drive ......................................................... A circuitTransfer number:CB400N .................................................... 2,800CB400FIII ................................................. 3,000Internal diameter of landing apertures шестерен:М5, М6:Nominal ..................................... 25,000 - 25,021 mmLimiting ................................................... 25,050 mmС2, СЗ, С4:Nominal ..................................... 28,000 - 28,021 mmLimiting ................................................... 28,050 mmExternal diameter of cartridges шестерен:М5, М6:Nominal ..................................... 24,959 - 24,980 mmLimiting ................................................... 24,920 mmС2, СЗ, С4:Nominal ..................................... 27,959 - 27,980 mmLimiting ................................................... 27,920 mmInternal diameter of landing apertures of cartridges:М5:Nominal ..................................... 21,985 - 22,006 mmLimiting ................................................... 22,070 mmС2:Nominal ..................................... 24,985 - 25,006 mmLimiting ................................................... 25,070 mmBacklash between шестернями and cartridges:М5, Mb:Nominal ......................................... 0,020 - 0,062 mmLimiting ..................................................... 0,10 mmС2, СЗ, С4:Nominal ......................................... 0,020 - 0,062 mmLimiting ..................................................... 0,10 mmBacklash between шестернями and shaft:М5:Nominal ......................................... 0,020 - 0,062 mmLimiting ..................................................... 0,10 mmС2:Nominal ......................................... 0,005 - 0,039 mmLimiting ..................................................... 0,05 mmExternal diameter шеек a primary shaft:М5 (1):Nominal ..................................... 21,959 - 21,980 mmLimiting ................................................... 21,930 mm

Characteristics 7

шейка under the basic cartridge (2):Nominal ....................................... 21,967 - 21,980 mmLimiting......................................................27,930 мм

External diameter шеек a secondary shaft: С2 (1):Nominal ......................................... 24,967-24,980 mmLimiting......................................................24,930 мм

Plug of switching of transfers:Thickness (4):Nominal .............................................. 5,93-6,00 mmLimiting ................................................... 5,60 mmInternal diameter of a landing apertureUnder a rod (5):Nominal. ...................................... 12,000-12,021 mmLimiting ................................................... 12,060 mmDiameter of a rod of plugs of switching of transfers:Nominal ....................................... 11,969-11,980 mmLimiting....................................................11,900 мм

Suspension bracketForward suspension bracket:Type .......................................................... TelescopicCourse ........................................................ 130 mmDiameter of a pipe ....................................... 41 mmVolume of oil ............................................... 499 sm3Height of a spring ...................................... 338,2 mmBack suspension bracket:Type ............................................................ PendularCourse ........................................................ 110 mmHeight of a spring.........................................225,3 мм

Brake systemForward brake:

Course of the lever ................................... 20-30 mm

Brake liquid ............................................... DOT 3 or 4Thickness of a disk ................................... 4,5 mmDiameter ГТЦ:

Nominal .................................... 14,000-14,043 mmLimiting ................................................. 14,060

mmDiameter of piston GTTS:


mmDiameter of the brake cylinder:

Nominal .................................. 27,000 - 27,050 mmLimiting ................................................. 27,060

mmDiameter of the piston of the brake cylinder:


mmBack brake:

Course of a pedal....... .............................. 10 - 20 mm

Height of a pedal ...................................... 67,5 mmBrake liquid ............................................... DOT 3 or

4Thickness of a disk ................................... 5,0 mmDiameter ГТЦ:


mmDiameter of piston GTTS:


mmDiameter of the brake cylinder:


mmDiameter of the piston of the brake cylinder:


mmPressure in trunks:(1) One driver:Forward wheel .......................................... 2,00 kg / sm2Back wheel ............................................... 2,25 kg / sm2(2) The driver and the passenger:Forward wheel .......................................... 2,00 kg / sm2Back wheel ............................................... 2,50 kg / sm2Dimension of trunks:Forward wheel ...................................... 110/70-17 54НBack wheel ........................................... 140/70-17 66НRecommended models (CB400N):Forward wheel...........Bridgestone G547, Dunlop K505F

Back …………………... Bridgestone G548, Dunlop K505Recommended models (CB400FIII):Forward wheel …..Bridgestone BT-35F, Dunlop GT401FBack wheel ……… Bridgestone BT-35R, Dunlop GT401Electric equipment:The generator: MaximalCapacity ................................ 312 Вт at 5000 rev/minPressure(Voltage) ........................................ 14-16 InFeedback current..................... 0-8 And (5000 rev/min)АКБ .............................................................. 12В, 8Ач

8 Characteristics

Current зарядки:5-10 ч ......................................................... 0,8 And1ч ............................................................... 4 AndLamps (CB400N):Headlight .................................................... 55/60 ВтStoplight and dimension ............................. 18/5 ВтForward turn indicatorsAnd dimensions .......................................... 18/5 ВтBack turn indicators turn ............................. 15 ВтIndicators of a combination of devices ........ 1,7 ВтThe indicator of excess allowable speeds ... 3,4 ВтLamps (CB400FIII):Headlight .................................................... 70/80 ВтResistance of the gauge of temperature охлажкGiving liquid (at 80°С) ........................... 47 - 57 whomThe gauge - switch on temperature охлажкдающей liquids:Temperature of inclusion ............................ 98 - 102°СTemperature of deenergizing.......................93 - 97°С

Honda CB400F(CB1) Honda

NC27 CB400F (СВ1)Length ....................................................... 2035 mmWidth ......................................................... 705 mmHeight ....................................................... 1025 mmBase .......................................................... 1375ммWeight:On a forward wheel .................................. 90 kgOn a back wheel ...................................... 93 kgFull ............................................................. 183 kgWeight full:On a forward wheel .................................. 110 kgOn a back wheel ...................................... 183 kgFull ............................................................ 293 kgКастер ..................................................... 25°30 'Width of a trace ........................................ 99 mmBrake way (about 50 km/h) ...................... 14 mRadius of a turn ........................................ 2,8 mThe engineUpdating ................................................... NC23EType .......................................................... 4-тактный, 4-cylinderWorking volume ....................................... 399 sm3ГРМ .............................. DOHC, a drive шестернямиDiameter of the cylinder ........................... 55,0 mmCourse of the piston ................................. 42,0 mmDegree of compression ............................ 11,3Capacity ............................... 57 h.p. at 11500 rev/minTwistingThe moment ..................... To 39 them at 9500 rev/minSystem of cooling ..................................... Liquid

System of greasing Refueling capacities: The dry engine ................................................. 3,5 лWith replacement of the filter ........................... 3,1 лWithout replacement of the filter ...................... 2,9 л

Cooling systemRefueling capacities : In total .................................................................... 1,7 лрасширительный a tank ..................................... 0,3 лPressure of opening of the valveCovers of a radiator .............................. 1,1-1,4 kg / sm2The temperature started openingтермостата .................................................. 80-84°СTemperature of full openingтермостата ....................................................... 95°СHeight of rise of the valve термостата...............8 ммSystem of submission of fuel (CB400Fk)Fuel tank. ....................................... 11 л (a reserve 3,5 л)The carburettor..... .............................. VG06AThrottle .............................................. 32,5 mmThe screw of quality ............................ 21/4Level of fuel in поплавковой to the chamber 6 mmThe main jet .......................................№ 105Jet of idling .........................................№ 35Frequency of rotationIdling .................................................. 1300ё100 rev/minIgnition systemType .............................………… Transistor батарейнаяSpark plugs:

Standard:NGK............................................................CR8EH9Denso......................................................U24FER-9

"Cold":NGK...........................................................CR9EH9Denso......................................................U27FER-9

Backlash....................................................0,8-0,9 ммCorner of an advancing of ignition(at 1300ё100 rev/min) ........................... 18°доВМТThe coil of ignition:Primary winding ..................................... 2-4 OhmSecondary windingWith tips ............................................... 23 - 27 whomWithout tips ............................................ 13-17 whomThe breaker:Resistance ......................................... 340 - 420 OhmPressure(Voltage) of a signal ................ More 0,7В

Start systemLength of brushes of a starter:

Nominal ................................................... 12,5 mmLimiting .................................................... 8,5 mm

Effort of a spring of a brush ........................ 7,8-10,6 НCylinder block head

Thermal backlashes in valves:Admission ......................................... 0,12-0,18 mmRelease ............................................. 0,17-0,23 mmPressure of the end of a step of compression(at 400 rev/min) ................................. 13 barPhases газораспределения: the inlet valve:Opening ............................................ 5 ° сo BMTClosing .............................................. 33 ° after НМТThe final valve:Opening ............................................ 33 ° up to НМТClosing .............................................. 5 ° after ВМТ

Characteristics 9

Height of cams of camshafts (1): an admission:Nominal ....................................... 33,070 - 33,230 mmLimiting ........................................... 33,020 mmRelease:Nominal .......................................... 33,120-33,280 mmLimiting ............................................-. 33,070 mmDiameter basic шеек (2):Nominal ....................................... 22,959 - 22,980 mmLimiting ........................................... 22,950 mmBacklash in the bearing distributiveShaft ............................................... 0,020 - 0,062 mmDiameter of a core of the valve: inlet:Nominal .......................................... 3,775-3,790 mmLimiting ........................................... 3,700 mmFinal:Nominal ........................................... 3,755 - 3,770 mmLimiting ............................................... 3,690 mmInternal diameter of the directing cartridge:Nominal .......................................... 3,800 - 3,812 mmLimiting ........................................... 3,890 mmLimiting backlash between the cartridge and a core of the valve:Inlet ................................................ 0,04 mmFinal ............................................... 0,05 mmHeight выступания the directing cartridge (h):Inlet ................................................ 13,37-13,77 mmFinal................................................11,52 -11,92 мм

Height of a spring of the valve:Nominal ..................................................... 39,40 mmLimiting.........................................................38,60 мм

The piston and the cylinderDiameter of the cylinder:Nominal ..................................... 55,000 - 55,010 mmLimiting ................................................... 55,100 mmDiameter of the piston:Nominal ....................................... 54,960 - 54,990ммLimiting ................................................... 54,900 mmBacklash between the cylinder and the piston:Nominal ......................................... 0,010 - 0,050 mmLimiting .................................................... 0,100 mmDiameter of an aperture under a piston finger:Nominal ....................................... 14,002-14,008 mmLimiting......................................................14,050 мм

Diameter of a piston finger:Nominal ..................................... 13,994-14,000 mmLimiting . ................................................. 13,980 mmBacklash between a finger and the piston:Nominal ....................................... 0,002 - 0,014 mmLimiting ..................................................... .0,04 mmInternal diameter of the piston head of a rod:Nominal ..................................... 14,016-14,034 mmLimiting ................................................... 14,070 mmBacklash between a finger and a rod:Nominal ......................................... 0,016-0,040 mmLimiting ..................................................... 0,060 mmBacklash between a flute and the piston: компрессионноеRing ............................................... 0,015-0,050 mmLimiting ....................................................... 0,080ммBacklash in the lock: top компрессионное a ring:Nominal ............................................. 0,18-0,28 mmLimiting ......................................................... 0,5 mmBottom компрессионное a ring:Nominal ............................................. 0,18-0,33 mmLimiting ......................................................... 0,5 mmмаслосъемное a ring:Nominal ............................................. 0,20-0,70 mmLimiting..........................................................1,1 мм

Crank shaftAxial backlash:Nominal ............................................... 0,05-0,20 mmLimiting ....................................................... 0,30 mmBacklash in bearings: шатунный the bearing:Nominal ......................................... 0,020 - 0,052 mmLimiting ....................................................... 0,06 mmThe radical bearing:Nominal ........................................... 0,022-0,046 mmLimiting........................................................0,05 мм

CouplingFree course of the lever of coupling ............ 10-20 mmThickness of a disk: nominal:"А". ........................................................ 3,22-3,38 mm"В" ......................................................... 3,22-3,38 mm"С" ......................................................... 3,42-3,58 mmLimiting:"А"... .............................................................. 2,90 mm"В"... .............................................................. 2,90 mm"С" ................................................................ 3,10 mmHeight of springs:Nominal ......................................................... 37,5 mmLimiting..........................................................36,0 мм

10 Characteristics

Diameter of the basic cartridge:Internal:Nominal ..................................... 21,980 - 22,007 mmLimiting ..................................................... 22,050 mmExternal:Nominal ..................................... 29,994 - 30,007 mmLimiting ..................................................... 29,950 mmInternal diameter of an asterisk of a drive маслянокго the pump:Nominal ..................................... 30,025 - 30,075 mmLimiting ..................................................... 30,130 mmBox of transfers Transfer numbers of transfers:Forward transfer ................................... 2,181 (44/96)CHECK POINT:1-st transfer .......................................... 3,307 (13/43)2-nd transfer ......................................... 2,352 (17/40)3-rd transfer .......................................... 1,875 (16/30)4-th transfer .......................................... 1,590 (22/35)5-th transfer .......................................... 1,434 (23/33)6-th transfer .......................................... 7,333 (24/32)The main transfer:Drive .............................................................. A circuitTransfer number ................................... 2,600 (13/59)Internal diameter of landing apertures шестерен:М5, М6:Nominal ..................................... 25,000 - 25,021 mmLimiting ..................................................... 25,050 mmС2, СЗ, С4:Nominal ..................................... 28,000 - 28,021 mmLimiting ..................................................... 28,050 mmExternal diameter of cartridges шестерен:М5, М6:Nominal ..................................... 24,959 - 24,980 mmLimiting ..................................................... 24,920 mmС2, СЗ, С4:Nominal ..................................... 27,959 - 27,980 mmLimiting ..................................................... 27,920 mmInternal diameter of landing apertures of cartridges:М5:Nominal....... .............................. 27,985 - 22,006 mmLimiting ..................................................... 22,070 mmС2:Nominal ..................................... 24,985 - 25,006 mmLimiting ..................................................... 25,070 mmBacklash between шестернями and cartridges:М5, М6:Nominal .......................................... 0,020 - 0,062 mmLimiting ........................................................ 0,10 mmС2, СЗ, С4:Nominal .......................................... 0,020 - 0,062 mmLimiting ........................................................ 0,10 mmBacklash between шестернями and shaft:М5:Nominal .......................................... 0,020 - 0,062 mmLimiting ........................................................ 0,10 mmС2:Nominal .......................................... 0,005 - 0,039 mmLimiting...........................................................0,05 мм

External diameter шеек a primary shaft: М5 (1):Nominal ....................................... 27,959 - 21,980 mmLimiting ..................................................... 21,930 mmшейка under the basic cartridge (2):Nominal ....................................... 21,967 - 21,980 mmLimiting......................................................21,930 мм

External diameter шеек a secondary shaft: С2 (3):Nominal ....................................... 24,967 - 24,980 mmLimiting......................................................24,930 мм

Plug of switching of transfers:Thickness (4):Nominal ............................................. 5,93 - 6,00 mmLimiting ................................................... 5,60 mmInternal diameter of a landing apertureUnder a rod (5):Nominal ........................................ 12,000-12,021 mmLimiting ................................................... 12,060 mmDiameter of a rod of plugs of switching of transfers:Nominal ........................................ 11,969-11,980 mmLimiting....................................................11,900 мм

Suspension bracketForward suspension bracket:Type ........................................................... TelescopicCourse ........................................................... 130 mmDiameter of a pipe .......................................... 41 mmVolume of oil ................................................ 570 sm3Height of a spring ....................................... 324,5 mmBack suspension bracket:Type ............................................................. PendularCourse ........................................................... 770 mmHeight of a spring............................................178 мм

Characteristics 11

Arrangement of cables, hoses and жгутов postings (1) (CB400N.) 1 - accelerator cable, 2 - brake hoses, 3 - starter switch wire, 4 - a wire of the switch of turn indicator, 5 - coupling lever cable, 6 - a cable of management of the starting device.

Brake systemForward brake:Course of the lever ................................. 20-30 mmBrake liquid ............................................ DOT 4Thickness of a disk:Nominal .................................................. 6 mmLimiting ................................................... 5 mmDiameter ГТЦ:Nominal ..................................... 11,000-11,043 mmLimiting ................................................. 11,060 mmDiameter of piston GTTS:Nominal ..................................... 10,957-10,984 mmLimiting ................................................. 10,950 mmDiameter of the brake cylinder:Nominal ................................... 27,000 - 27,050 mmLimiting ................................................. 27,060 mmDiameter of the piston of the brake cylinder:Nominal ................................... 26,918 - 26,968 mmLimiting....................................................26,910 мм

Back brake:Course of a pedal ................................. 10 - 20 mmHeight of a pedal .................................... 67,5 mmBrake liquid ............................................. DOT 4Thickness of a disk:Nominal ..................................................... 5 mmLimiting ................................................... 4 mmDiameter ГТЦ:Nominal ................................... 14,000-14,043 mmLimiting ................................................. 14,060 mmDiameter of piston GTTS:Nominal ................................... 13,957-13,984 mmLimiting ................................................. 13,950 mmDiameter of the brake cylinder:Nominal ................................... 38,180-38,230 mmLimiting ................................................. 38,240 mmDiameter of the piston of the brake cylinder:Nominal .................................................. 38,098-38,148 mmLimiting....................................................38,090 мм

12 Characteristics

Arrangement of cables, hoses and жгутов postings (2) (CB400N.) 1 - a clip of posting, 2 - a socket главкного the switch (2Р, Б), 3 · a socket of the switch of a starter (9Р, Кч), 4 - a socket of a combination прибокров (6Р, Б), 5 - a socket of the switch of es of turn (4Р, Ч), 6 - a socket of a combination of devices (6Р, Кр), 7 - a socket of the switch of es of turn (6Р, С), 8 - headlight socket.

Pressure in trunks:(1) One driver:Forward wheel .................................. 2,25 kg / sm2Back wheel ....................................... 2,25 kg / sm2(2) The driver and the passenger:Forward wheel .................................. 2,25 kg / sm2Back wheel ....................................... 2,50 kg / sm2Dimension of trunks:Forward wheel .................................. 110/70-17 54НBack wheel ....................................... .140/70-17 66Н

Electric equipment:The generator: MaximalCapacity.... ........................... 325 Вт at 5000 rev/minPressure(Voltage) ....................................... 14-16 InCurrent of feedback ............. 0-8 And (5000 rev/min)АКБ. ............................................................ 12В, 8АчCurrent зарядки:5-10 ч ......................................................... 0,8 And1ч.... ............................................................. . 4 And

Lamps (CB400Fk):Headlight.. .................................................. 60/55 ВтStoplight and dimension ............................. 23/8 Втes of turn ..................................................... 15 ВтForward dimensions ................................... 3,4 ВтIndicators of a combinationDevices ....................................................... 1,7 ВтResistance of the gauge of temperature охлажкдающей liquids:At 80°С .................................................. 47 - 57 OhmAt 120°С ................................................. 14-18 OhmThe gauge - switch on temperature охлажкдающей liquids:Temperature of inclusion .......................... 98 - 102°СTemperature of deenergizing......................93 - 97°С

Characteristics 13

Arrangement of cables, hoses and жгутов postings (3) (CB400N.) 1 - starting device cable, 2 - a wire of the switch of es of turn, 3 - starter switch wire, 4 - a cable акселерактора, 5 - the case термостата, 6 - the top hose of a radiator, 7 - a siphon tube, 8 - coupling cable.

14 Characteristics

Arrangement of cables, hoses and жгутов postings (4) (CB400N.) 1 - speedometer cable, 2 - left торкмозной a hose, 3 - temperature guage socket of a cooling liquid, 4 - a brake hose, 5 - a pin, 6 - the basic жгут postings, 7 - a socket of weight, 8 - gauge socket- switch on темпекратуре a cooling liquid.

Characteristics 15

Arrangement of cables, hoses and жгутов postings (5) (CB400N.) 1 - a ventilating tube топливкного a tank, 2 - a drain tube of a fuel tank, 3 - a siphon tube, 4 - accelerator cable, 5 - starting device cable, 6 - coupling cable, 7 - a returnable tube.

Arrangement of cables, hoses and жгутов postings (6) (CB400N.) 1 - a tube of ventilation картера, 2 - the basic жгут postings, 3 - a wire of the negative plug of the storage battery, 4 - a wire of the positive plug of the storage battery, 5 - a cable of the lock of a seat, 6 - pressure(voltage) regulator, 7 - starter wire, 8 - a wire of the generator of pulses (breaker).

16 Characteristics

Arrangement of cables, hoses and жгутов postings (7) (CB400N.) 1 - ignition unit, 2 - air tubes, 3 - accelerator cable, 4 - a siphon tube, 5 - the basic жгут postings.

Arrangement of cables, hoses and жгутов проводкки (8) (CB400N).1 - a wire of the switch of stoplights,2 - a drain tube of a fuel tank,3 - a ventilating tube of a fuel tank,4 · a siphon tube,5 - a returnable tube,6 - an adapter

Technical Characteristics 17

Arrangement of cables, hoses and жгутов postings (9) (CB400N.) 1 - oil pressure gauge, 2 - проквод the negative plug of the storage battery, 3 - coupling cable, 4 - generator wire, 5 - a wire of a starter, 6 - breaker wire, 7 - a wire of the switch of prohibition of start, 8 - проквод the switch of a lateral support.

Расположение тросов, шлангов и жгутов проводки (10) (CB400N). 1 - провод указателей поворота (правый), 2 - основной жгут проводки, 3 - стопор, 4 - задний тормозной шланг, 5 - стопор.

18 Technical Specifications

Arrangement of cables, hoses and жгутов postings (11) (CB400N.) 1 - a wire of stoplights switch, 2 - a wire of the positive plug of the storage battery, 3 - the switch of the relay старктера, 4 - the relay of es of turn, 5 · a drain tube of a fuel tank, 6 - a tube of the fuel crane, 7 - a fuel tube, 8 - a tube of ventilation картера, 9 - a siphon tube, 10 - a cable of an accelerator, 11 - an auxiliary air line of the air filter, 12 - a tube of ventilation of the carburettor, 13 - a returnable tube, 14 - a tube of ventilation of a fuel tank, 15 - a wire of the negative plug of the storage battery.

Technical Specifications 19

Arrangement of cables, hoses and жгутов проводкки (11) (CB400FIII.) 1 - a wire of a combination прибокров, 2 - a wire of the of turn, 3 - a wire of the gauge of excess of allowable speed.

Arrangement of cables, hoses and жгутов проводкки (12) (CB400FIII.) 1 - a wire of the switch старктера, 2 - wires of switches, 3 - a wire укакзателей turn, 4 - a collar.

Arrangement of cables, hoses and жгутов postings (13) (CB400FIII.) 1 - ignition module, 2 - a cable аккселератора, 3 - a siphon tube, 4 - the basic жгут postings.

20 Technical characteristics

Arrangement of cables, hoses and жгутов проводкки (14) (CB400FIII).1 - a wire of the switch of a stoplight,2 - a drain tube,3 - a by-pass tube,4 - a ventilating tube,5 - a siphon tube.

Arrangement of cables, hoses and жгутов postings (15) (CB400FIII.) 1 - a wire positive клемкмы the storage battery, 2 - starter relay, 3 - a drain tube, 4 - tubes of ventilation картера, 5 - a tube of the additional air filter, 6 - a fuel tube, 7 - a siphon tube, 8 - accelerator cable, 9 gauge of position throttle заслонки, 10 by-pass tube, 11 - вентиляционкная a tube.

Arrangement of cables, hoses and жгутов postings (16) (CB400F.) 1 - a socket of a starter and the switch of the engine (9Р, Кр), 2 - a socket of ignition lock (ЗР, Б), 3 - a socket of a combination of devices (6Р, Б), 4 - a socket of a combination of devices (6Р, Кр), 5 - a socket of es of turn (6Р, 3).

Arrangement of cables, hoses and жгутов postings (17) (CB400F.) 1 - a wire of steering switches (right), 2 - accelerator cable, 3 - brake, a hose, 4 - coupling cable, 5 - a wire of helmsmans выкключателей (left), 6 - a cable of the starting device, 7 - a wire of the lock of ignition, 8 - a wire указатеклей turn, 9 - the basic жгут postings.

22 Технические характеристики

Arrangement of cables, hoses and жгутов postings (18) (CB400F.) 1 - a clip high-voltage провокдов cylinders № 2 and 3, 2 - coupling cable, 3 - a collar, 4 - high-voltage wires of cylinders № 1 and 4, 5 - the basic жгут postings, 6 - a cable of the starting device, 7 - a clip, 8 - accelerator cable, 9 - a brake hose, 10 - high-voltage wires.

Arrangement of cables, hoses and жгутов postings (19) (CB400F.) 1 - coupling cable, 2 cable акселекратора, 3 - a clip of high-voltage wires of cylinders № 1 and № 4, 4 - a siphon tube, 5 - a cable спикдометра, 6 - high-voltage wires of cylinders № 1 and 4, 7 - a cable of the starting device, 8 - высококвольтные wires.

Arrangement of cables, hoses and жгутов postings (20) (CB400F.) 1 - the ignition module, 2 - the diode, 3 - the storage battery, 4 - a wire of the ignition lock, 5 - a clip, 6 - жгут postings (high-voltage wires, a wire of the switch of prohibition of start, a wire of the breaker, a wire of the switch of a support, a wire of the generator).

Arrangement of cables, hoses and жгутов postings (21) (CB400F.) 1 - a clip, 2 - a clip, 3 - a socket прекрывателя, 4 - high-voltage wires of cylinders № 1 and 4, 5 - an air hose, 6 - a socket выклюкчателя supports, 7 - high-voltage wires of cylinders № 2 and 3, 8 - a socket of the generator, 9 - a clip, 10 - a socket of coils of ignition, 11 - a drain tube of a fuel tank, 12 - a by-pass tube, 13 - задкний a brake hose, 14 - a hose.

24 Technical characteristics

Arrangement of cables, hoses and жгутов postings (22) (CB400F.) 1 - the fuel filter, 2 - аккумукляторная the battery, 3 - the rectifier, 4 - the relay of es of turn, 5 - the relay of switching-off of submission топклива, 6 - the fuel pump, 7 - a wire of the switch of a support, 8 - a wire of the oil pressure gauge, 9 - a wire of the breaker, 10 - жгут postings (high-voltage wires, a wire of the switch закпрещения start, a wire of the breaker, a wire of the switch of a support, a wire of the generator).

Arrangement of cables, hoses and жгутов проводкки (23) (CB400F.) 1 - a clip, 2 - the basic жгут postings, 3 - the diode, 4 - the ignition module. Arrangement of cables, hoses and жгутов

проводкки (24) (CB400FM.) 1 - a brake hose of a forward brake, 2 - a socket of a combination of devices (6Р, Б), 3 - a socket of a combination of devices (6Р, Кр), 4 - a coupling cable, 5 - a socket of helmsmans выклюкчателей (left) (6Р, Ч), 6 - a socket of helmsmans выкключателей (left) (6Р, 3), 7 - a wire of a sound signal, 8 - a socket of a headlight, 9 - a socket of steering switches (right) (9Р, Кр), 10 - a socket of the lock of ignition (ЗР, Ч).

Technical characteristics 25

Arrangement of cables, hoses and жгутов postings (25) (CB400FM.) 1 - a wire of steering switches (right), 2 - a wire of the ignition lock, 3 - a wire of a combination of devices, 4 - coupling cable, 5 - a speedmeter cable, 6 - a cable of the starting device, 7 - a wire of steering switches (left), 8 - a wire of es of turn, 9 - the basic жгут postings, 10 - a brake hose of a forward brake, 11 - a cable of an accelerator.

Arrangement of cables, hoses and жгутов проводкки (26) (CB400FM.) 1 - the basic жгут postings, 2 - coupling cable, 3 - an accelerator cable, 4 - a brake hose of a forward brake, 5 - выксоковольтные wires of cylinders № 2 and 3.

Arrangement of cables, hoses and жгутов проводкки (27) (CB400FM.) 1 - high-voltage wires of cylinders № 2 and 3, 2 - high-voltage wires of cylinders № 1 and 4, 3 - жгут postings (coils of ignition, the switch of prohibition of start, oil pressure gauge, the breaker, выклюкчателя supports, the generator).

26 Technical Characteristics

Arrangement of cables, hoses and жгутов postings (28) (CB400FM.) 1 - a cable of coupling, 2 - a by-pass tube, 3 - high-voltage wires of cylinders № 1 and 4, 4 - a ventilating tube, 5 - the basic жгут postings, 6 - a by-pass tube, 7 - a cable of the starting device, 8 - a cable of a speedmeter, 9 - the gauge - switch on temperature of a cooling liquid, 10 - a socket of the fan.

Arrangement of cables, hoses and жгутов postings (29) (CB400FM.) 1 - a high-voltage wire циклиндра № 1, 2 - a cable of an accelerator, 3 - a tube of ventilation картера, 4 - a socket of the generator, 5 - the basic жгут postings, 6 - a socket of the coil of ignition, 7 - the breaker, 8 - a socket of the switch of a support, 9 - an air hose, 10 - a by-pass tube, 11 - a cable of the starting device, 12 - a high-voltage wire of the cylinder № 4, 13 - a hose of a radiator, 14 - the switch of prohibition of start, 15 - выключактель supports.

Arrangement of cables, hoses and жгутов postings (30) (CB400FM.) 1 - a hose of a tank of a working liquid of the back shock-absorber, 2 - the rectifier, 3 - a tank of a working liquid of the back shock-absorber, 4 - топкливный the pump, 5 - the fuel filter.

Arrangement of cables, hoses and жгутов проводкки (31) (CB400FM.) 1 - a by-pass tube, 2 - a wire of the negative plug of the storage battery, 3 - a drain tube, 4 - a wire of the positive plug of the storage battery, 5 - a by-pass tube расширительного a tank.

Arrangement of cables, hoses and жгутов проводкки (32) (CB400FM) .1 - a wire of the negative plug of the storage battery, 2 - a wire покложительной plugs of the storage battery.

28 Technical Characteristics

Arrangement of cables, hoses and жгутов postings (33) (CB400FM.) 1 - a frame of a seat, 2 - the basic жгут postings, 3 - a lateral cover, 4 - a wire of the positive plug of the storage battery, 5 - проквод a starter, 6 - a drain tube, 7 - a wire of the relay of a starter, 8 - a drain tube, 9 - a by-pass tube расширительного a tank, 10 - the switch of a stoplight (a back brake), 12 - a hose of a tank тормозкной liquids of a back brake, 13 - the relay of a starter.

Расположение тросов, шлангов и жгутов проводки (34) (CB400FM). 1 - топливный шланг, 2 - выпрями-тель, 3 - вывод массы, 4 - реле указателей поворота, 5 - реле отключения подачи топлива, 6 - топ-ливный насос, 7 -трос спидометра, 8 - провод прерывателя.

Кузовные elementsAttention: removal and disassembly of units and unitsIt is carried out by way of numbers specified onFigures.Assembly and installation are carried out in the order,The opposite to disassembly and removal.

Кузовные elements (1.1 - back facing, 2 - a forward wing, 2 - a fuel tank, 4 - пекреднее a wing, 5 - a back wing.

Fuel tank (2). 1 - a vacuum tube, 2 - венктиляционная a tube, 3 - a drain tube, 4 -

топкливная a tube.Lateral facing. 2 - a bolt of fastening.

Сиденье.

1 - lateral facing,

Fuel tank (1). 1 - a fuel tank, 2 - fastening bolt (12 Н-м), 3 - the cartridge.

30 Кузовные elements

Back facing (1).1 - a back lantern, 2 - гайкки fastenings, 3 - safety cartridges, 4 - саморез. Back wing (2).1 - fastening bolt, 2 - nuts, 3 - a

bolt, 4 - a back wing.

Back facing (2).1 - back facing, 2 - the screw, 3 - fastening bolt, 4 - саморез, 5 - the screw.

Back wing (1).1 - the handle, 2 - fastening bolt.

Forward wing (1).1 - the cartridge, 2 - a nut, 3 - кронкштейн a brake hose, 4 - a bolt, 5 - a forward wing.

Кузовные elements 31

Luggage compartment (1).1 - the back shock-absorber, 2 - fastening bolt.

Luggage compartment (2). 1 - fastening bolt, 2 - раскширительный a tank.

Forward wing (2). Fastening bolt

Luggage compartment (3). 1 - the starter relay, 2 - the relay of es of turn, 3 - a luggage compartment.

Fuel tank (CB400R.) 1 - a bolt, 2 - a socket of the fuel level gauge, 3 - a vacuum tube, 4 - a fuel tube, 5 - a drain tube, 6 - венктиляционная a tube.

The muffler (CB400N.) 1 - a nut of fastening, 2 - a back bolt and a nut of fastening, 3 - a washer, 4 - the cartridge, 5 - a forward bolt and a nut of fastening, 6 - a washer, 7 - the cartridge, 8 - an exhaust pipe and the muffler in gathering, 9 - an arm of a pipe.

The muffler (CB400FIII.) 1 - nuts of fastening, 2 - a back bolt of fastening of the muffler, 3 - a washer, 4 - втулкка, 5 - a forward bolt of fastening of the muffler, 6 - a washer, 7 · the cartridge, 8 - the muffler, 9 - a lining, 10 - bolts of fastening of the muffler, 11 - a bolt of fastening of the muffler, 12 - the muffler, 13 - a lining.

Кузовные elements

Кузовные elements 33

The muffler (CB400F.) 1 - a radiator, 2 - a lining, Fuel tank (CB400F.) 1 – a bolt, 2 – fuel tank3 - adjusting nuts, 4 - the muffler. 3 – a nut, 4 - fastening bolt, 5 – fuel tube,

6 – a drain tube.

Lateral обтекатель (1) (CB400F.) 1 - a lobby Lateral обтекатель (2) (CB400F.) 1 – backpart lateral обтекателя, 2 - fastening bolt. part lateral обтекателя, 2 fastening bolt.

34 Кузовные elements

Forward обтекатель (CB400FIII.) 1 - a rod, 2 - the bottom bolt of fastening, 3 - the top bolt of fastening, 4 - обтекатель.

Maintenance service

Honda CB400N

Arrangement of elements (1) (CB400N.) 1 - a tank of a brake liquid of a back brake, 2 - выключактель a stoplight, 3 - расширительный a tank of system of cooling, 4 - щуп a level of oil, 5 - рукояткка an accelerator, 6 - the lever of a forward brake, 7 - a tank of a brake liquid of a forward brake, 8 - a headlight, 9 - a forward brake support, 10 forward wheel, 11 - the forward trunk, 12 - the oil filter, 13,14 - заглушки, 15 - a pedal of a back brake, 16 - a back brake hose, 17 - back торкмозной a support.

Arrangement of elements (2) (CB400N.) 1 - coupling lever, 2 - the lever of the starting device, 3 - ГРМ, 4 - spark plugs, 5 - the screw of an emphasis throttle заслонки, 6 - the carburettor, 7 - the air filter, 8 - the back shock-absorber, 9 - a back wheel, 10 - the back trunk, 11 - a chain, 12 - a lateral support, 13 - a bolt for a plum of oil, 14 - a radiator hose, 15 - the bearing of a steering column, 16 - a brake hose, 17 - a forward plug.

35

36 Maintenance service

The air filter

Periodicity of replacement...............................20000

1 - a filtering element, 2 - a cover of the case of the air filter.

Check of thermal backlashes in valves

Check (CB400N)Attention : Check and adjustment of backlashes in клакпанах is carried out on the cold engine (below 35°С).1. Remove(Take off) a cover of the head of the block of cylinders.2. Take заглушки.

3. Establish the piston of the cylinder № 1 in ВМТ a step of compression, having turned a cranked shaft before overlapping labels, as shown in figure (risks on asterisks with a plane of a socket of a cover, label "Т" on маховикке with an adjusting label on a cover картера).

1 - labels on asterisks (in a plane of a socket of a cover of the head of the block of cylinders), 2 - устаноквочная a label, 3 - a label "Т".

4. Check up a backlash in the following valves:

Cylinder Valve1 IN/EX2 ЕХ3 IN

Note : Numbering of cylinders is conducted with леквой the parties(sides) by way of 1-2-3-4. A nominal backlash:

IN..........................................................0,15±0,03 ммЕХ........................................................0,20±0,03мм

1 - щуп.5. Turn a cranked shaft on one revolution on to hour hand and again combine labels, as пок казано is higher.6. Check up a backlash in the following valves:

Cylinder Valve

2 IN

3 ЕХ4 IN/EX

1 - a lateral cover, 2 - the fastening screw.

1, 2 -заглушки.

Maintenance service 37

Check (CB400R)Attention : Check and adjustment of backlashes in клакпанах is carried out on the cold engine (below 35°С).1. Remove(Take off) a cover of the head of the block of cylinders.2. Take заглушки.

1, 2 -заглушки.3. Establish the piston of the cylinder № 1 in ВМТ a step of compression, having turned a cranked shaft before overlapping labels, as shown in figure (risks on asterisks with a plane of a socket of a cover, label "Т" on маховикке with Adjusting label on a cover картера).-

Camshaft of inlet valves,1 - a camshaft final клапакIt is new, 3 - an adjusting label, 3 - a label "Т".4. Check up a backlash in inlet (IN) valves циклиндров № 1 and 3.Nominal backlash:

IN ………………………………. 0,15 ё0,03 mm5. Turn a cranked shaft on 180 ° on hour to arrow(pointer), having combined labels, as shown in figure.

6. Check up a backlash in final (ЕХ) valves цик линдров № 2 and 4.Nominal backlash:

ЕХ.......................................................0,22 ± 0,03 мм7. Turn a cranked shaft on 180 ° on hour to arrow(pointer), having combined labels, as shown in figure.8. Check up a backlash in inlet (IN) valves ци линдров №2

и 4.Nominal backlash:IN...........................................................0,15 ±0,03 мм

9. Turn a cranked shaft on 180 ° clockwise, having combined labels, as shown in figure.

10. Check up a backlash in final (ЕХ) valves циклиндров № 1 and 3. Nominal backlash:

EX...................................................... 0,22 ± 0,03 ммAdjustment (if necessary)1. Отверните заглушку the holder натяжителя circuits.

1 - the holder натяжителя, 2 - заглушка (bolt), 3 - a washer.

2. Screw спецприспособление.

3. Remove(Take off) a camshaft.4. Remove(Take off) a pusher of the valve and adjustingWasher.5. Measure thickness of the removed(the taken off) adjusting washer.6. Pick up a new adjusting washer onTo the formula.A=B-C+DА - thickness of a new washer,В - a measured backlash,С - a nominal backlash (IN - 0,15 mm, ЕХ - 0,20 mm),D - thickness of the removed(the taken off) washer.

Adjusting washers are issued 65 sizes, thickness from 1,200 up to 2,800 mm with step of 0,025 mm.

1 - fastening bolt, 2 - успокоитель circuits (В),3 - a label "F". ,

9. Repeatedly check up a backlash in valves.

Adjustment and synchronization of carburettors

Entry conditions:1) The engine прогрет up to the normal worker temperatures,2) Neutral transfer is included.1 - спецприспособление.

1,80 мм 1,825 мм 1,85 мм 1,875 мм

7. Establish washers and pushers.8. Establish a camshaft.

1 - the adjusting cartridge, 2 - covers подшипникков.

Maintenance service

1. Отверните adjusting screws inlet as cash of carburettors № 2, 3, 4.2. Disconnect a vacuum tube from fuel the crane.

1 - a vacuum tube, 2 - the screw.3. Connect with the help of an adapter a tester toTo entrance channels of carburettors № 2,3,4.4. Connect a vacuum tube of the carburettor№ 1 with the help of a tee to a tester and fuel to the crane, as shown in figure.

1 - a tee, 2 - tester tubes.

5. Warm up the engine and with the help of the screw of an emphasis throttle заслонки adjust frequency врак щения idling.

Nominal

Frequency of rotation ................... 1200 ё 100 rev/min

6. Adjust carburettors.Synchronization is made on the carburettor № 2а) Check up a difference of underpressure between карбюк раторами.NominalDifference ……………………..Up to 30 mm of a hg.б) If necessary adjust her(it) вращекнием screws.

1 - Adjusting screws.

в) Adjust frequency of rotation of idling. 7. Remove(take off) a tester, connect back tubes and turn screws.

Adjustment of system of idlingNote : Adjustment of system of idling is carried out by the manufacturer and необходикмости in repeated adjustment does not arise, except for cases of replacement of the case карбюрактора or adjusting screws. Before разборккой it is necessary to put on the screw of a label and at assembly to establish it(him) in a starting position.

1 - the screw of idling, 2 - спецприспособление.1. Connect a tachometer (with a margin error less50 rev/min).2. Turn the screw of quality against the stop, and then вык return it(him) in nominal position (on 21/2Revolution).3. The ambassador прогрева the engine establish the screw the cook личества the minimal frequency of rotation холосток го a course.Frequency of rotationIdling ............................................. 1200 ё 100 rev/min

1 - винт упора дроссельной заслонки.

1 - the screw of quantity(amount).

Rotating screws of quality of each of carburettors on 1/2 revolutions on and counter-clockwise, achieve the maximal frequency of rotation of idling. After several fluctuations frequency of rotation хоклостого a course should be stabilized.4. Turning the screw of quality of the carburettor № 2 on1/2 revolutions, establish the maximal frequency rotations of idling.5. Repeat item 4 for carburettors № 1,3,4.6. After several fluctuations frequency of rotation it should be stabilized at a nominal level(1200 rev/min).7. Gradually turn the screw of quality карбюраток ра № 2, that frequency of rotation of idling became on 50 rev/min below nominal.8. From position of item 7, отверните the screw of quality in обк the military party(side) on 3/4 revolutions (before reception номик нальной frequencies of rotation of idling).9. Repeat item 7 and 8 for carburettors № 1,3,4.If necessary repeat procedure регулик ровки, since item 4.

Check of the switch of a support1. At the put forward support the engine owes startкаться by the included neutral transfer of a check point.2. If on the working engine at included to transfer and the put forward support to press the lever couplings, the engine should decay. If the specified conditions are not carried out, проверькте the switch of a support.

Honda CB400F(CB1)

Air filter

Periodicity of replacement................................20000 км

Check of thermal backlashes in valves

Check (CB400F)1. Remove(Take off) a cover and turn out заглушки.

1 - заглушка apertures of check УОЗ, 2 - крышкка, 3 - central заглушка.2. Remove(Take off) the case of the air filter.3. Отверните bolts of fastening of a radiator and снимик those it(him).

1 - the top bolt of fastening, 2 - the bottom bolts of fastening, 3 - a radiator.4. Remove(Take off) a cover of the head of the block of cylinders.5. Turn a cranked shaft before overlapping мек current, as shown in figures.

1 - A camshaft of inlet valves, 2 - Camshaft of final valves, 3 - labels.

1 - a filtering element, 2 - a label "upwards", 3 - жгут postings.

1 - a label "Т", 2 - щуп, 3 - a label.

Maintenance service 41

Arrangement of elements (1) (CB400F.) 1 - ГРМ, 2 - bearings of a steering column, 3 - a headlight, 4 - the lever of coupling, 5 - the lever of the starting device, 6 - the air filter, 7 - the carburettor, 8 - the fuel filter, 9 - the back shock-absorber, 10 - приводная a circuit, 11 - a support, 12 - расширительный a tank охклаждающей liquids, 13 - the carburettor, 14 - a bolt a plum of motor oil, 15 - a hose of a radiator, 16 - spark plugs, 17 - a forward plug.

Arrangement of elements (2) (CB400F.) 1 - a tank of a brake liquid of a back brake, 2 - a back brake hose, 3 - a pedal of a back brake, 4 - расширительный a tank, 5 - the handle of an accelerator, 6 - a tank of a brake liquid of a forward brake, 7 - the lever of a forward brake, 8 - a forward brake hose, 9 - the forward brake cylinder, 10 - the forward trunk, 11 - a forward wheel, 12 - the oil filter, 13 - заглушки, 14 - the gauge of a level of oil, 15 - the switch of stoplights, 16 - a back wheel, 17 - the back trunk.


Cylinder Valve

2 IN

3 EX

4 IN/EX

Nominal backlash:IN.........................................................0,15 ±0,03 ммEX........................................................0,20 ±0,03 мм

7. Turn a cranked shaft on one revolution clockwise and again combine labels.

1 - Camshaft of inlet valves, 2 - a camshaft of final valves, 3 - labels.


Cylinder Valve

1 IN/EX

2 ЕХ3 IN

9. If necessary adjust a backlash as покказано is higher for models CB400N.

Adjustment of the carburettorAdjustment of carburettors is carried out similarly to adjustment of carburettors for models CB400N.

1 - The screw of quality of the cylinder № 1,2-screw of quality of the cylinder № 2, 3 - the screw of quality of the cylinder №3.

Check of the switch of a support1. At the put forward support the engine should be started by the included neutral transfer of a check point.

2. If on the working engine by the included transfer and the put forward support to press the lever of coupling, the engine should decay. If the specified conditions are not carried out, check up the switch of a support.

Periodicity THATEach 6 months:- Check свечей ignitions,- Clearing of the air filter,- Check of connections of system of greasing,- Check of a free course of the lever of coupling,- Check of a tension приводной circuits,

- Check of a free course of the lever forward brakes,- Check of a free course of a pedal back brakes,- Check of hoses and connections of brake system,- Check of pressure in trunks,- Check of a condition of final system,- Check of structure of fulfilled gases,- Check of a level of motor oil,- Check of fastening of wheels,- Check of deterioration of trunks.Each 12 months:- The same, as each 6 months, and also:- Check of hoses and connections of system of submission of fuel,- Check of hoses and connections of system of cooling,- Check люфтов a forward suspension bracket and the helmsman managements, check of ease of rotation of a rudder,- Check of a level of a brake liquid,- Check of deterioration brake колодок,- Check of deterioration of brake disks,- Adjustment of a corner of an advancing of ignition,- Check of work throttle заслонок and starting devices,- Check of a level of a cooling liquid,- Check of asterisks приводной circuits,- Check of a condition of brake cylinders,- Check of a condition of a pendulum of a back suspension bracket,- Check of plugs of the storage battery,- Replacement of motor oil,- Adjustment of the carburettor,- Check of thermal backlashes in valves.After 20000 km:- Replacement of the air filter.After 6000 km- Replacement of motor oil.After 12000 km- Replacement of the oil filter.At operation in heavy conditions maintenance service on some items(points) of the plan makes in 2 times more often. To heavy conditions concern: operation on the roads bumpy, dirty or covered with a thawing snow, operation on dusty roads, operation on roads, посыпанных salt against an icing, often trips on short distance at negative temperatures, excessive work idling and driving "внатяг".

1 - заглушки.

Lubrication System

Honda CB400N

The circuit of system of greasing (CB400N.) 1 - the oil pump, 2 - маслоприемник, 3 - редукционный the valve, 4 - the oil filter, 5 - a target shaft of a check point, 6 - a conducting(leading) shaft of a check point, 7 - a camshaft of final valves, 8 - a camshaft of inlet valves, 9 - the piston, 10 - a cranked shaft, 11 - the gauge of pressure of oil.

43

44 System of greasing

The oil pump (removal and installation). 1 - a bolt of fastening of the oil pallet, 2 - the oil pallet, 3 - a lining, 4 - редукционный the valve, 5 · ring condensation, 6 - маслоприемник, 7 - ring condensation, 8 - a bolt of fastening of an asterisk of a drive of the oil pump, 9 - a washer, 10 - an asterisk of a drive of the oil pump, 11 - bolts of fastening of the oil pump, 12 - the oil pump, 13 adjusting cartridge.

The oil pump (disassembly and assembly) (CB400N.) 1 - the screw of fastening, 2 - a cover of the pump, 3 - an adjusting pin, 4 - a conducted rotor, 5 - a conducting(leading) rotor, 6 - a pin, 7 - a shaft of the oil pump, 8 - a washer, 9 - the case of the oil pump.

System of greasing 45

The circuit of system of greasing (CB400F.) 1 - редукционный the valve, 2 - the oil filter, 3 - a secondary shaft of a check point, 4 - a primary shaft of a check point, 5 - oil channels, 6 - a rod, 7 - the piston, 8 - a camshaft of final valves, 9 - a camshaft of inlet valves, 10 - a cranked shaft, 11 - the gauge of pressure of oil, 12 - oil channels, 13 - the oil pump, 14 - маслоприемник.

Honda CB400F(CB1)

46

Cooling system

The circuit of system of cooling (CB400N.) 1 - the pump of a cooling liquid, 2 - the bottom (final) hose of a radiator, 3 - a radiator, 4 - термостат, 5 - the top (inlet) hose of a radiator, 6 - расширительный a tank, 7 - branch pipes.

Honda CB400NЗамена охлаждающей жидкости

1. Отверните сливной болт из корпуса насоса охла-ждающей жидкости.

3. Отверните a drain bolt from the block of cylinders.

1 - Drain bolt, 2 - a washer.

4. Turn drain bolts.

1 - Drain bolt, 2 - a washer.

2. Отверните a cover of a

radiator.1 - крышка радиатора.

Расширительный a tank. 1 - a bolt of fastening, 2 - расширительный a tank, 3 - a siphon tube, 4 - a by-pass tube.

System of cooling 47

The pump of a cooling liquid (CB400N.) 1 - a bolt, 2 - a cable of switching of transfers, 3 - a bolt of a cover of a drive, 4 - a cover of a drive, 5 - the prorate, 6 - the bottom hose of a radiator, 7 - a hose (from the engine), 8 - a bolt of a cover of the pump, 9 - a bolt of fastening of the pump, 10 - a cover of the pump, 11 - ring condensation, 12 - the case of the pump of a cooling liquid, 13 - ring condensation.

48 System of cooling

Radiator (removal and installation) (CB400N.) 1 - a socket of the fan, 2 - the top hose of a radiator, 3 bottom hose of a radiator, 4 - fastening bolt, 5 - the cartridge, 6 - a radiator.

Radiator (disassembly and assembly) (CB400N.) 1 - a bolt of fastening, 2 - lateral facing, 3 - a lattice of a radiator, 4 - a socket of the gauge - switch on temperature of a working liquid, 5 - a bolt of fastening of a casing of the fan, 6 - a conclusion of weight, 7 - a casing of the fan, 8 - a nut of fastening крыльчатки the fan, 9 - крыльчатка the fan, 10 - the screw of fastening of the fan, 11 - the electric motor of the fan, 12 - the gauge - switch on temperature of a cooling liquid, 13 - ring condensation, 14 - a radiator.

Термостат (CB400N.) 1 - a wire of weight, 2 - a socket of the gauge of temperature of a cooling liquid, 3 - a hose термостата (from the head of the block of cylinders), 4 - a bolt of fastening, 5 - the case термостата, 6 - ring condensation, 7 - a bolt of fastening of a cover термостата, 8 - a conclusion of weight, 9 - a cover термостата, 10 - ring condensation, 11 - термостат, 12 - the gauge of temperature cooling жидкоксти, 13 - the case термостата.

Honda CB400F(CB1)

The circuit of system of cooling (CB400F.) 1 - the fan of a radiator, 2 - термостат, 3 - a cover of a radiator, 4 - the gauge of temperature of a cooling liquid, 5 - a siphon tube, 6 - расширительный a tank of a cooling liquid, 7 - the pump of a cooling liquid, 8 - the switch on temperature of a cooling liquid, 9 - a radiator.

50 System of cooling

Radiator (removal and installation) (CB400F.) 1 - a hose of a radiator, 2 - a socket of the gauge - switch on temperature of a cooling liquid, 3 - the bottom bolt of fastening, 4 - the top bolt of fastening, 5 - a socket of the fan, 6 - the cartridge.

Radiator (disassembly and assembly) (CB400F.) 1 - bolts of fastening of facing, 2 - lateral facing, 3 - a lattice of a radiator, 4 - a bolt of fastening of a casing of the fan, 5 - a nut of fastening, 6 - the electric motor of the fan, 7 - крыльчатка the fan, 8 - the gauge - switch on temperature of a cooling liquid, 9 - ring condensation, 10 - a conclusion of weight.

Термостат (CB400F.) 1 - a bolt of fastening, 2 - a siphon tube, 3 - a hose of a radiator, 4 - a socket of the gauge of temperature of a cooling liquid, 5 - a cover термостата, 6 - ring condensation, 7 - термостат, 8 - the gauge of temperature of a cooling liquid, 9 - the case термостата, 10 - a ventilating aperture.

The pump of a cooling liquid (CB400F.) 1 - a hose of a radiator, 2 - a bolt of fastening of the pump, 3 - a bolt of fastening of a cover of the pump, 4 - an arm, 5 - a cover of the pump of a cooling liquid, 6 - ring condensation, 7 - the case of the pump of a cooling liquid, 8 - ring condensation, 9 - a shaft of a drive, a 10-shaft of the pump.

52

Fuel system

Honda CB400N

Carburettors (removal and installation) (CB400N.) 1 - a bolt of an arm of the module of ignition, 2 - the module of ignition, 3 - the screw of a lateral cover of the case of the air filter, 4 - a lateral cover of the air filter, 5 - the screw of a collar, 6 - a bolt of the case of the air filter, 7 - ventilating tubes, 8 · a tube of ventilation картера, 9 - an auxiliary air tube, 10 - a collar, 11 - a cable of the starting device, 12 - the carburettor, 13 - a cable of an accelerator, 14 - the case of the air filter.

Fuel System 53

Carburettors (removal and installation, 2) (CB400N.) 1 - a fuel tube, 2 - the screw of fastening of an arm, 3 - a washer, 4 - a spring, 5 - an arm, 6 - the cartridge, 7 - шпилька fastenings of carburettors (5 mm), 8 - шпилька fastenings of carburettors (6 mm), 9 - a spring (the carburettor № 3), 10 - a tee (air-line), 11 - the cartridge (5 mm), 12 - the cartridge (6 mm), 13 - a spring (the carburettor № 1), 14 - a spring, 15 - an adapter (air-line), 16 - a tee (air-line), 17 - a tee (a fuel line), 18 - an adjusting pin (5 mm), 19 - an adjusting pin (6 mm), 20 - a spring (the carburettor № 4), 21 - a spring, 22 - an adapter (air lines), 23 - a tee (air-line), 24 - a tee (a fuel line), 25 - an adjusting pin (5 mm), 26 - an adjusting pin (6 mm).

54 Fuel System

The carburettor (disassembly and assembly) (CB400N.) 1 - the screw of a cover of the vacuum chamber, 2 - a cover of the vacuum chamber, 3 - a spring, 4 - a zolotnik, 5 - the holder of a needle, 6 - ring condensation, 7 - a spring эмульксионной tubes, 8 dosing out needle, 9 - a washer, 10 - the screw поплавковой chambers, 11 - поплавковая the chamber, 12 - ring condensation, 13 - an axis of a float, 14 - a float, 15 - the needle valve, 16 - the main jet, 17 - a spray, 18 - a jet of idling, 19 - the screw of quality, 20 · a spring, 21 - a washer, 22 · ring condensation, 23 - the screw, 24 - the case отсечного the valve, 25 - ring condensation, 26 - отсечной the valve, 27 - a nut плунжера the starting device, 28 - a spring, 29 - плунжер the starting device.

1 - Spring,2 - the holder of a needle,3 - ring condensation,4 - a dosing out needle,5 - a washer.

Fuel System 55

1 - the case of the starting device, 2 – starting 1 - отсечной the valve, 2 - the case, 3 - the screw device. of fastening.

The gauge of position throttle заслонки (CB400FIII.) 1 - a cover of the gauge, 2 - a socket of the gauge of position throttle заслонки, 3 - the screw of fastening, ' 4 - the gauge of position throttle заслонки, 5 - an adapter.

56 Fuel System

Honda CB400F(CB1)

The case of the air filter (CB400F.) 1 - жгут postings, 2 - a heat-shielding casing, 3 - a cover of the air filter, 4 - a filtering element, 5 - a bolt of fastening of the case, 6 - a tube of ventilation картера, 7 - an air hose, 8 - the case of the air filter, 9 - a bolt of fastening, 10 - a cover of the additional filter, 11 - a filtering element, 12 - the case of the additional air filter, 13 - an air jet, 14,15 - spark plugs.

Carburettors (removal and installation, 1) (CB400F.) 1 - a collar, 2 - a cable of the starting device, 3 - a cable throttle заслонки, 4 - a fuel tube, 5 - carburettors, 6 - the prorate.

14

Fuel System 57

Carburettors (removal and installation, 2) (CB400F.) 1 - draft of the starting device, 2 - a spring, 3 - the lever of the starting device, 4 - an arm of a cable of the starting device, 5 - a back arm, 6 - a forward arm, 7 - a spring of the carburettor № 3, 8 - a tee (air-line), 9 - a tee (a fuel line), 10 - a spring of the carburettor № 4,11 - a spring, 12 - an adapter (air-line), 13 - a tube of tap(removal), 14 - a tee (a fuel line), 15 - a spring (the carburettor № 1), 16 - a spring, 17 - an adapter (air-line), 18 - a tube of tap(removal), 19 - a tee (a fuel line).

58 Fuel System

The carburettor (disassembly and assembly) (CB400F.) 1 - the screw of the vacuum chamber, 2 - a cover of the vacuum chamber, 3 - a spring, 4 - a zolotnik, 5 - the holder of a needle, 6 - a spring, 7 - a saddle of a spring, 8 - a dosing out needle, 9 - a washer, 10 - the screw of fastening поплавковой chambers, 11 - an axis of a float, 12 - the needle valve, 13 - a saddle of the valve, 14 - a washer, 15 - the fuel filter, 16 - the main jet, 17 - a spray, 18 - a jet of idling, 19 - a nut плунжера, 20 - a spring, 21 - плунжер the starting device, 22 - the screw of quality, 23 - a spring, 24 - a washer, 25 - ring condensation, 26, 27 - the directing cartridge.

The power(force) unit

Honda CB400N

The power(force) unit (removal and installation) (CB400N.) 1 - a bolt of a tube of a cooling liquid, 2 - a tube of a cooling liquid, 3 - ring condensation, 4 - the oil filter, 5 - a socket of the generator, 6 and *9632; a socket of the switchboard, 7 - a socket of the gauge of pressure of fuel, 8 - a wire of a starter, 9 - a wire масксы, 10 - a cable of coupling, 11 - a bolt of fastening of a conducting(leading) asterisk, 12 - a washer, 13 - a conducting(leading) asterisk, 14 - a bolt of an arm of fastening, 15 - the cartridge, 16 - a bolt of an arm (65 mm), 17 - a bolt of an arm (60 mm), 18 - an arm, 19 - a nut шарнирного a bolt, 20 - шарнирный a bolt, 21 - a nut шарнирного a bolt, 22 - a washer, 23 - шарнирный a bolt, 24 - the basic cartridge, 25 - the power(force) unit in gathering.

59

60 The power(force) unit

The power(force) unit (removal and installation) (CB400F.) 1 - tips of high-voltage wires, 2 - a socket of the breaker, 3 - a socket of the generator, 4 - a socket of the gauge of pressure of oil, 5 - a wire of a starter, 6 - a wire of weight, 7 - an adapter of a hose of a cooling liquid, 8 - ring condensation, 9 - a cable of coupling, 10 - an arm of a pedal of switching of transfers, 11 - a lateral cover of the pump of a cooling liquid, 12 - a cable of a speedmeter, 13 - a casing of a conducting(leading) asterisk, 14 - успокоитель circuits, 15 - the adjusting cartridge, 16 - a hose of a cooling liquid, 17 - a bolt of fastening of a conducting(leading) asterisk, 18 - a washer, 19 - a conducting(leading) asterisk, 20 - the bottom back bolt of fastening of the engine, 21 - a lock nut, 22 - an adjusting bolt, 23 - a washer, 24 - a forward bolt of fastening of the engine, 25 - a bolt of fastening of an arm, 26 - an arm, 27 - a bolt of fastening, 28 - a cover of a bolt, 29 - the top back bolt of fastening of the engine, 30 - the engine in gathering.

Honda CB400F(CB1)

Engine

Honda CB400N

Cover of the head of the block of cylinders (CB400N.) 1 - bolts of fastening of a radiator, 2 - a socket of the gauge of temperature of a cooling liquid, 3 - a socket of weight, 4 - a tip of a high-voltage wire, 5 - the coil of ignition, 6 - a drain bolt, 7 - directing жгута postings, 8 - a jellied mouth of a radiator, 9 - a tube of ventilation картера, 10 - a bolt of a cover of the head of the block of cylinders, 11 - a washer, 12 - a cover of the head of the block of cylinders, 13 - a lining, 14 - a bolt, 15 - a plate, 16 - a lining.

61

62 Engine

Camshafts (CB400N.) 1 - заглушка, 2 - ring condensation, 3 - заглушка, 4 - ring condensation, 5 - a bolt of a cover of bearings of a camshaft, 6 - успокоитель circuits, 7 - a cover of bearings of a camshaft, 8 - an adjusting pin, 9 - a camshaft of inlet valves, 10 - a camshaft of final valves.

Fastening of an asterisk of a camshaft (the moment of an inhaling(a prolongation) 20 Н-м).

Engine 63

The block of cylinders (CB400N.) 1 - a bolt of fastening of a branch pipe of a cooling liquid, 2 - a branch pipe of a cooling liquid, 3 - ring condensation, 4 - a bolt of fastening натяжителя circuits, 5 - натяжитель circuits, 6 - a lining натяжителя, 7 - a bolt of fastening, 8 - the cylinder, 9 - a lining, 10 adjusting pin, 11 - a lock ring, 12 - a piston finger, 13 - the piston, 14 - top компрессионное a ring, 15 - bottom компрессионное a ring, 16 - маслосъемное a ring.

64 Engine

The head of the block of cylinders (CB400N.) 1 - a bolt of fastening of a branch pipe of a cooling liquid, 2 - a branch pipe of a cooling liquid, 3 - a bolt of fastening of the head of the block of cylinders, 4 - nuts of fastening of the head of the block of cylinders, 5 - the head of the block of cylinders in gathering, 6 - a lining, 7 - the adjusting cartridge, 8 - the prorate of the carburettor.

1 - Fastening nut of the head of the cylinder block. 1 - Fastening nut, 2 - Fastening bolt.

Engine 65

The head of the block of cylinders (CB400N.) 1 · a pusher, 2 - an adjusting washer, 3 - crackers, 4 - spring plate, 5 - valve spring, 6 - the inlet valve, 7 - the final valve, 8 - маслосъемный колпачок, 9 - spring saddle, 10 - the directing cartridge of the valve.

Honda CB400F(CB1)

Camshafts (CB400F.) 1 - the heat-shielding screen, 2 - a bolt of fastening of a cover of the head of the block of cylinders, 3 - a washer, 4 - a cover of the head of the block of cylinders, 5 - a lining, 6 - a bolt of a cover of bearings of a camshaft, 7 - a cover of bearings of a camshaft, 8 - an adjusting pin, 9 - a camshaft of inlet valves, 10 - a camshaft of final valves, 11 - a pin.

66 Engine

The head of the block of cylinders (removal and installation) (CB400F.) 1 - a washer, 2 - a bolt of fastening of the head of the block of cylinders, 3 - the head of the block of cylinders, 4 - a lining, 5 - the adjusting cartridge, 6 - a bolt of the mechanism of drive ГРМ, 7 - the adjusting cartridge, 8 - a washer, 9 - the mechanism of drive ГРМ, 10 - the prorate.

The head of the block of cylinders (disassembly and assembly) (CB400F.) 1 - a pusher, 2 - an adjusting washer, 3 - crackers, 4 - spring plate, 5 - valve spring, 6 - the valve, 7 - маслосъемный колпачок, 8 - spring saddle, 9 - the directing cartridge of the valve.

Engine 67

The block of cylinders (CB400F.) 1 - bolts of fastening of a branch pipe of a cooling liquid, 2 - a branch pipe of a cooling liquid, 3 - ring condensation, 4 - a bolt of fastening of the head of the block of cylinders, 5 - the cylinder, 6 - a lining, 7 - the adjusting cartridge, 8 - a lock ring, 9 - a piston finger, 10 - the piston, 11 top компрессионное a ring, 12 - bottom компрессионное a ring, 13 - маслосъемное a ring.

Removal and installation of camshafts1. At removal and installation of camshafts adjusting labels should be combined, as shown in figure.1 - Labels,2 - a camshaft of inlet valves,3 - a camshaft of final valves,4 - labels,5 - a label "Т",6 - an adjusting label on a cover картера.

68 Engine

2. Fastening bolts of camshaft bearing covers turn away Removal and installation of drive ГРМ and turned in regular intervals for 2-3 passes

The moment of an inhaling(a prolongation) ........ 12 Н-м1 - The case of a drive, 2 - conducted шестерня, 3 - the leader шестерня, 4 - intermediate шестерня, 4 - an adjusting pin.

The inhaling(prolongation) of fastening bolts of drive ГРМ is carried out in the order shown in figure.

1 - The adjusting cartridge, 2 - fastening bolts, 3 - the adjusting cartridge.

Cover картера couplings (Honda CB400N). 1 - a socket of the generator, 2 - a clip of posting, 3 - a bolt of an arm of a cable of coupling, 4 - a cable of coupling with an arm, 5 - a bolt of fastening of a cover картера Couplings, 6 - the right cover картера couplings, 7 - a lining, 8 - the adjusting cartridge, 9 - press пята, 10 - a returnable spring, 11 - a clamp(fixing agent) of a spring, 12 - a rod of deenergizing of coupling, 13 - пыльник.

69

Engine

70 Engine

Cover картера couplings (CB400F.) 1 - a cable of coupling, 2 - a socket of the generator, 3 - a bolt of fastening of a cover, 4 - a cover картера couplings, 5 - a lining, 6 - the adjusting cartridge, 7 - press пята, 8 - a returnable spring, 9 - a clamp(fixing agent) of a spring, 10 - a rod of deenergizing of coupling, 11 - an omentum, 12 - a cover картера № 2,13 - заглушка № 1,14 - заглушка № 2.

Engine 71

Coupling. 1 - a bolt of an adjusting plate of coupling, 2 - выжимная a spring of coupling, 3 - выжимной the bearing, 4 - springs of coupling, 5 - the central nut, 6 - a washer, 7 - coupling in gathering, 8 - a nave of coupling (an internal drum), 9 - демпфирующая a spring, 10 - a saddle демпфирующей springs, 11 - a frictional disk (С), 12 - a smooth disk (В), 13 - a frictional disk (В), 14 - a smooth disk (А), 15 - a frictional disk (А), 16 - press a disk, 17 - a basket of coupling, 18 - the needle bearing (basic), 19 - a bolt of fastening of an asterisk of a drive of the oil pump, 20 - a washer, 21 - an asterisk of a drive of the oil pump, 22 - a circuit of a drive of the oil pump, 23 - a conducting(leading) asterisk of the oil pump, 24 - the basic cartridge.

72 Engine

1 - Basket of coupling, 2 - conducted шестерня, 3 - conducting(leading,leader) шестерня.

1 - Conducted шестерня, 2 - auxiliary шестерня, 3, 4 - the basic needle bearing.

Installation of coupling

1 - Basket of coupling, 2 - a label "Т"

Removal of coupling

1 - Basket of coupling, 2 - the basic cartridge, 3 - a screw-driver.

1 - Conducted шестерня, 2 - the leader шестерня, 3 - a basket of coupling.

Engine 73

1 - Conducting(Leading) asterisk, 2 - a basket of coupling.

The mechanism of switching of transfers. 1 - a bolt of the lever of switching of transfers, 2 - the lever of switching of transfers, 3 - a shaft of switching of transfers, 4 - a persistent Washer, 5 - a lock ring, 6 - a returnable spring of a shaft, 7 - the cartridge, 8 - a bolt копирнои plates, 9 - копирная a plate and a directing cam in gathering, 10 - копирная a plate, 11 - собачка a ratchet, 12 - плунжер, 13 - a spring, 14 - a directing cam, 15 - the cartridge, 16 - the adjusting cartridge, 17 - a spring of the terminator, 18 - the cartridge, 19 - the terminator, 20 - a washer, 21 - a bolt of fastening of a drum of a ratchet, 22 - a drum of a ratchet, 23 - an adjusting pin.

74

Cranked shaft and transmission

Carter. 1 - the top fastening bolts картера (6 mm), 2 - the bottom fastening bolts картера (6 mm), 3 - the bottom fastening bolts картера (8x65 mm), 4 - the bottom fastening bolts картера (8x88 mm), 5 - the bottom fastening bolts картера (8x75 mm), 6 - the bottom part картера, 7 - an adjusting pin, 8 - the oil union, 9 top part картера.

Cranked shaft and transmission 75

Cranked shaft1. At replacement of radical loose leaves it is necessary to use loose leaves of corresponding dimensional group.There are some standard dimensional groups of the loose leaves designated "А", "В", "С", "Е", three dimensional groups of diameter of bed of the radical bearing (And, In, С) and two dimensional groups of diameter radical шейки a cranked shaft (1, 2).

1 - Label on a cranked shaft.

1 - Label on картере.

The table for definition of dimensional groups of radical loose leaves (CB400N)

Label on the block

Diameter lay the radical bearing (мм)

А В С

Label on a shaft

Diameter шейки a shaft (мм) 33,000 - 33,008 33,008-33,016 33,016-33,024

1 29,992 - 30,000 С (Ж) В(3) А (Ж)

2 29,984 - 29,992 В(3) А (Кч) Е(Ч)

Table for definition of dimensional groups of radical loose leaves (CB400F)

Label on the block

Diameter lay the radical bearing (мм)

А В С

Label on a shaft

Diameter шейки a shaft (мм) 33,000 - 33,008 33,009-33,016 33,017-33,024

1 29,992 - 30,000 D (Рз) С (Ж) В(3)

2 29,984 - 29,992 С (Ж) В(3) А (Кч)

76 Cranked shaft and transmission

Cranked shaft. 1 - a bolt, 2 - a rod натяжителя circuits, 3 - успокоитель circuits, 4 - a nut of a cover of a rod, 5 - a cover of a rod, 6 - the piston with a rod, 7 - шатунный the loose leaf, 8 - шатунный a bolt, 9 - a cranked shaft, 10 - a circuit of drive ГРМ, 11 - the loose leaf of the radical bearing.

Primary shaft. 1 - an external holder of the needle bearing, 2 - the needle bearing, 3 - a persistent washer, 4 - the leader шестерня 2-nd transfers (15), 5 - a persistent washer, 6 - the leader шестерня 6-th transfers (23), 7 - шлицевая the cartridge conducting(leading) шестерни 6-th transfers, 8 - шлицевая a washer, 9 - a lock ring, 10 - conducting(leading) шестерни 3-rd and 4-th transfers (16/21), 11 - a lock ring, 12 - шлицевая a washer, 13 - the leader шестерня 5-th transfers (25), 14 - the cartridge conducting(leading) шестерни 5-th transfers, 15 - a persistent washer, 16 - the basic bearing, 17 - a primary shaft and the leader шестерня 1-st transfers (13).

1 - Color Label on the loose leaf.

2. At replacement шатунных loose leaves it is necessary to use loose leaves of corresponding dimensional group.There are some standard dimensional groups of the loose leaves designated "А", "В", "С", two dimensional groups of diameter of the bottom head of a rod (1, 2) and two dimensional groups of diameter шатунной шейки a cranked shaft (А, В). The table for definition of dimensional groups шатунных loose leaves

Label on a rodDiameter bottom 1 2 The head of a rod (мм)Label Diameter шейки 32,992 - 33,000 - On a shaft (мм) 33,000 33,008 To shaftAND 29,992-30,000 С (Ж) В (3) В 29,984-29,992 В (3) А (Кч)

1 - Color label on the loose leaf.

Transmission1. Put germetic on a surface of a socket картера.

2. Establish the bottom part картера, having arranged plugs of switching of transfers, as shown in figure.

1 - Conducted шестерня 5-th transfers, 2 - conducting(leading) шестерни 3-rd and 4-th transfers, 3 - conducted шестерня 6-th transfers, 4 - the left plug of switching of transfers, 5 - the central plug of switching of transfers, - the right plug of switching of transfers.

1 - Label on a rod.

1 - Label on a cranked shaft.

78 Cranked shaft and transmission

Box of transfers (1).1 - a target shaft, 2 - a lock ring, 3 - fastening bolts of clamp(fixing agent) BXДд-ного of a shaft, 4 - a clamp(fixing agent) of a primary shaft, 5 - a primary shaft, 6 - fastening bolt of a plug (central), 7 · a lock washer, 8 - an axis of plugs of switching of transfers, 9 - a plug of switching of transfers (left), 10 - a plug of switching of transfers (central), 11 - a plug of switching of transfers (right), 12 - a clamp(fixing agent) of a drum of the selector, 13 - an adjusting pin, 14 - a clamp(fixing agent) of a drum of the selector, 15 - drum bearing of the selector, 16 - a drum of the selector.

2. Adjust number of parts.Nominal number of parts...........................................1003. Establish a connecting part with newRing condensation.

Secondary shaft. 1 - the basic bearing, 2 - a persistent washer, 3 - conducted шестерня 1-st transfers (43), 4 - the needle bearing, 5 - a persistent washer, 6 - conducted шестерня 5-th transfers (31), 7 - a lock ring, 8 - шлицевая a washer, 9 - conducted шестерня 3-rd transfers (28), 10 - шлицевая the cartridge шестерни 3-rd transfers, 11 - a lock washer, 12 - шлицевая a washer, 13 · conducted шестерня 4-th transfers (30), 14 - шлицевая the cartridge шестерни 4-th transfers, 15 - шлицевая a washer, 16 - a lock ring, 17 - conducted шестерня 6-th transfers (29), 18 - a lock ring, 19 - шлицевая a washer, 20 - conducted шестерня 2-nd пекредачи (39), 21 - the cartridge шестерни 2-nd transfers, 22 - a persistent washer, 23 - an omentum, 24 - a secondary shaft.

Adjustment of length приводной circuits Connecting fingers should act on1. Выпрессуйте a finger of a connecting link. 1,2 -1,4 мм.

4. Расклепайте соединительные пальцы.

5. Check up diameter расклепанной parts of a finger.Nominal diameter.....................................5,55- 5,85 мм

1 -втулочное a part, 2 - ring condensation, 3 - a lateral plate.

80

Forward suspension bracket and steering column

Rudder (CB400N.) 1 - a mirror of a back kind, 2 - a socket of the switch of a stoplight (a forward brake), 3 - the main brake cylinder (a forward brake), 4 - the screw of fastening, 5 - an arm of the handle of an accelerator, 6 - a tip of a cable of an accelerator, 7 - the handle of an accelerator, 8 - a tip of a cable of coupling, 9 - a bolt of fastening, 10 - an arm of the lever of a drive of coupling, 11 - the lever of a drive сцеплекния, 12 - the screw of fastening, 13 - a tip of a cable of the starting device, 14 - the case of steering switches, 15 - the left handle of a rudder, 16 - the lever of a drive of the starting device, 17 - заглушки, 18 - a bolt of fastening of a rudder, 19 - an arm of fastening of a rudder, 20 - a rudder.

Forward suspension bracket and steering column 81

Steering column (CB400N.) 1 - a nut of fastening of a steering column, 2 - a washer, 3 - top траверса, 4 - the case of a headlight, 5 - a bolt, 6 - an arm of a brake hose, 7 - a lock nut, 8 - a lock washer, 9 - the top cover, 10 - top пыльник, 11 - a holder № 1, 12 - the top bearing, 13 - a steering column, 14 - the bottom bearing, 15 - a holder № 4,16 - bottom пыльник, 17 - a holder № 2,18 - a holder № 3.

Forward wheel (removal and installation) (CB400N.) 1 - bolts of fastening of a forward brake support, 2 - the right brake support, 3 - the left brake support, 4 - the screw, 5 - a cable of a speedmeter, 6 - bolts of fastening of a forward axis (клеммного connections), 7 - axis bolt, 8 - fastening bolts of a forward axis (клеммного connections), 9 - a forward axis, 10 - a forward wheel, 11 - the cartridge, 12 - a drive of a speedmeter.

82 Forward suspension bracket and steering column

Forward wheel (disassembly and assembly) (CB400N.) 1 - the left omentum (45x55x5), 2 - the holder of a drive of a speedmeter, 3 - the right omentum (28x42x8), 4 - a bolt of fastening of a brake disk, 5 · a brake disk, 6 - the left wheel bearing (6004UU), 7 - the cartridge, 8 - the right wheel bearing (6004UU).

Forward plug (disassembly and assembly) (CB400N.) 1 - a bolt of fastening of a wing, 2 - a forward wing, 3 - пыльник, 4 - the cartridge, 5 - a bolt of an arm of a brake support, 6 - the right brake support, 7 - the left brake support, 8 - a bolt клеммного connections top траверсы, 9 - a bolt клеммного connections bottom траверсы, 10 - a feather of a plug in gathering.

Feather of a plug (disassembly and assembly) (CB400N.) 1 - a fuse, 2 - ring condensation, 3 - the cartridge, 4 - a saddle of a spring, 5 - a spring, 6 - пыльник, 7 - a lock ring, 8 - a bolt, 9 - a washer, 10 - a rod of the shock-absorber, 11 - a sealing ring of a rod, 12 - a spring of a release, 13 - a pipe, 14 - an omentum, 15 - lock ring, 16 - the cartridge, 17 - the cartridge, 18 - an omentum, 19 - a tip.

Steering column (CB400FIII.) 1 - a bolt of fastening of a sound signal, 2 - a sound signal, 3 - a bolt of fastening of the index of turn, 4 - the index of turn, 5 - fastening bolt of an arm of a headlight, 6 - an arm of a headlight, 7 - a nut of fastening of a steering column, 8 - a washer, 9 - top траверса, 10 - a support of a headlight, 11 - a bolt, 12 - an arm of a brake hose, 13 - a lock nut, 14 - a lock washer, 15 - the top cover, 16 - пыльник, 17 - a holder № 1, 18 - the top bearing, 19 - a steering column, 20 - the bottom bearing, 21 - a holder № 4, 22 - пыльник, 23 - a holder № 2, 24 - a holder № 3.

Regulator of rigidity of a suspension bracket (CB400FII/IIIV)For change of rigidity of a back suspension bracket the regulator preliminary поджатия the springs, having five positions (1 - the biggest course, 5 - the smallest) serves. Position is standard №4.

The right handle of a rudder (CB400F.) 1 - a socket of the switch of a stoplight, 2 - the main brake cylinder (a forward brake), 3 - screws of fastening, 4 - the case of the handle of an accelerator, 5 - a nut of a cable аксе-лератора.6 - a cable of an accelerator, 7 - a tip of the handle, 8 - an arm of a cable, 9 - the handle of an accelerator, 10 - a lock ring, 11 - a bolt клеммного fastenings, 12 - the right handle of a rudder.

The left handle of a rudder (CB400F.) 1 - a socket of the switch of coupling, 2 - the lever of coupling, 3 - the screw of fastening, 4 - the case of the switch, 5 · a cable of the starting device, 6 - a tip of the handle, 7 - the handle (furnish), 8 - a lock ring, 9 - a bolt клеммного fastenings, 10 - the left handle of a rudder.

Forward wheel (removal and installation) (CB400F.) 1 - a bolt of an axis of a forward wheel, 2 - bolts клеммного fastenings, 3 - an axis of a forward wheel, 4 - a forward wheel, 5 - the left basic cartridge, 6 - the right basic cartridge.

Forward wheel (disassembly and assembly) (CB400F.) 1 - the right basic cartridge, 2 - the left basic cartridge, 3 - bolts of fastening of a disk, 4 - a brake disk, 5 · пыльник, 6 - the left wheel bearing (6004UU), 7 - the remote cartridge, 8 - the right wheel bearing (6004UU).

Forward plug (CB400F.) 1 - a bolt of fastening of a forward wing, 2 - a forward wing, 3 - the holder of a brake hose, 4 - bolts of an arm of a support, 5 - a brake support, 6 - bolts of fastening of a combination of devices, 7 - a bolt of fastening bottom траверсы, 8 - a bolt of fastening top траверсы, 9 - a plug.

Back suspension bracket

Back wheel (removal and installation). 1 - a nut of an axis, 2 - a nut of adjustment of a tension of a circuit of a drive, 3 - the right cartridge of adjustment of a tension of a circuit, 4 - приводная a circuit, 5 - a back axis, 6 - the left cartridge of adjustment of a tension of a circuit, 7 - a back wheel, 8 - the right basic cartridge, 9 - the left Basic cartridge.

89

90 Back suspension bracket

Back wheel (disassembly and assembly). 1 - a bolt of fastening of a brake disk, 2 - a brake disk, 3 - an asterisk of a drive in gathering, 4 - the shock-absorber, 5 - ring condensation, 6 - an omentum, 7 - the left wheel bearing (6303UU), 8 - the cartridge, 9 - the right wheel bearing (6303UU), 10 - a nut of fastening of an asterisk, 11 - a conducted asterisk, 12 - the cartridge of an asterisk, 13 - an omentum, 14 - the bearing of a conducted asterisk.

Back suspension bracket 91

The back shock-absorber (removal and installation). 1 - the top bolt of fastening, 2 - a washer, 3 - the bottom bolt of fastening, 4 - the back shock-absorber.

The back shock-absorber (disassembly and assembly) (CB400N.) 1 - the bottom saddle of a spring, 2 - a spring, 3 - the top saddle of a spring, 4 - a regulator of compression of a spring, 5 - the case of a regulator of compression of a spring, 6 - the shock-absorber.

Pendulum of a back suspension bracket (removal and installation) (CB400N.) 1 - a bolt of an arm of a brake hose, 2 - a brake hose, 3 - an arm of a back brake support, 4 - the bottom bolt of fastening of the shock-absorber, 5 - fastening bolt of a protective rod of a circuit, 6 - the cartridge, 7 - the safety cartridge, 8 - a protective rod of a circuit, 9 - a nut of an axis of the lever, 10 – lever axis, 11 - the lever of a back suspension bracket.

Regulator of rigidity of a suspension bracket (CB400FII/lllT)

For change of rigidity of a back suspension bracket the regulator preliminary поджатия the springs, having five positions (1 - the biggest course serves, 5 - the smallest). Position is standard №2.

Pendulum of a back suspension bracket (disassembly and assembly) (CB400N.) 1 - a regulator of a tension приводной circuits, 2 - a bolt успокоителя circuits, 3 - успокоитель приводной circuits, 4 - a bolt, 5 - a cross-section rod, 6 - the basic cartridge, 7 - an omentum (22x35x5), 8 - a lock ring, 9 - the bearing (6002), 10 - the cartridge, 11 - the cartridge, 12 - an omentum (24x32x5,5), 13 - the needle bearing.

The back shock -absorber (removal and installation CB400F (CB1)).1 - The top bolt of fastening,2 - the bottom fastening bolt,3 - the back shock -absorber.

The back shock-absorber (disassembly and assembly CB400F(CB1)).1 - The bottom eye of fastening2 The shock-absorber,3 - a stopper of a spring,4 - a saddle of a spring,5 - a spring,6 - a regulator,7 - a lock nut bottomEyes,8 - демпфер,9 - the shock-absorber.

The back shock-absorber (disassembly and assembly CB400FL).1 - Stopper of a spring,2 - a saddle of a spring,3 - a spring,4 - a regulator,5 - демпфер,6 - the shock-absorber.

Pendulum (removal and installation CB400F (СВ1)) .1 - a back support, 2 - a clip of a brake hose, 3 - the bottom bolt of fastening of the shock-absorber, 4 - a nut шарнирного a bolt, 5 - шарнирный a bolt, 6 - a pendulum.

Pendulum (disassembly and assembly CB400F (СВ1)). 1 - a regulator of a tension приводной circuits, 2 - the right basic cartridge, 3 · the left basic cartridge, 4 - a protective rod приводной circuits, 5 - успокоитель приводной circuits, 6 - right пыльник, 7 - left пыльник, 8 - the remote cartridge, 9 · a lock ring, 10 - the ball bearing, 11 - the needle bearing.

96

Brake system

Honda CB 400N

Lobbies brake колодки (CB400N.) 1 - заглушка, 2 - a clamp(fixing agent) колодок, 3 - brake колодки.

Back brake колодки (CB400N.) 1 - заглушка, 2 - fastening bolt of a support, 3 - a clamp(fixing agent) колодок, 4 - brake колодки.

Brake system 97

Forward support (removal and installation, CB400N). 1 - перепускной a bolt, 2 - washers, 3 - the union of a brake hose, 4 - bolts of fastening of a support, 5 - a forward brake support.

Back support (removal and installation, CB400N). 1 - перепускной a bolt, 2 - a washer, 3 - the union of a brake hose, 4 - a back brake support.

98 Brake system

Forward support (disassembly and assembly, CB400N). 1 - an arm of a support, 2 - a protective cover, 3 - a directing finger, 4 - a lamellar spring, 5 - the piston, 6 - a dustproof cuff, 7 - a sealing cuff, 8 - a directing finger, 9 protective cover, 10 - the union of prorolling, 11 - a support.

Back support (disassembly and assembly, CB400N). 1 - a lamellar spring, 2 - the piston, 3 - a dustproof cuff, 4 - a sealing cuff, 5 - a directing finger, 6 - the basic cartridge, 7 - a protective cover, 8 - the union of prorolling, 9 - a support, 10 - an arm of a support, 11 - a protective cover.

Brake system 99

The main brake cylinder of a forward brake (removal and installation, CB400N). 1 - the right mirror of a back kind, 2 - шарнирный a bolt of the lever of a brake, 3 - the lever of a brake, 4 - a socket of the switch of a stoplight, 5 - перепускной a bolt, 6 - the union of a brake hose, 7 - washers, 8 - a bolt of arm ГТЦ, 9 - arm ГТЦ, 10 - the main brake cylinder.

The main brake cylinder of a forward brake (disassembly and assembly, CB400N). 1 - the screw, 2 - a cover of a tank of a brake liquid, 3 - a plate of a membrane, 4 - a membrane, 5 - the switch of a stoplight, 6 - пыльник, 7 - a lock ring, 8 - the piston in gathering, 9 - a spring, 10 - brake lever.

100 Brake system

10 11 35 Нм

The main brake cylinder of a back brake (removal and installation, CB400N). 1 - a bolt of fastening of the muffler, 2 - a bolt of fastening of the right footstep, 3 - шплинт, 4 - the cartridge of a rod, 5 - a bolt of fastening ГГЦ, 6 - an arm of the switch of a stoplight, 7 - a spring of the switch of a stoplight, 8 - a returnable spring of a pedal of a brake, 9 - an arm of the right footstep, 10 - a bolt of fastening расширительного a tank, 11 - перепускной a bolt, 12 - the union of a brake hose, 13 - a washer, 14 - ГТЦ, 15 - a lock ring, 16 - a washer, 17 - brake pedal.

Brake system 101

The main brake cylinder of a back brake (disassembly and assembly, CB400N). 1 - a bolt of fastening of the union, 2 - the union, 3 - ring condensation, 4 - a tip of a rod, 5 - the rubber cartridge, 6 - a lock ring, 7 - a rod, 8 - piston GTTS, 9 - a spring, 10 - a collar, 11 - a hose of a tank of a brake liquid, 12 - a cover of a tank of a brake liquid, 13 - a plate, 14 - a membrane, 15 - a tank of a brake liquid.

Honda CB400FIIIT, CB400Flllv

Lobbies brake колодки (CB400FIIIT.) 1 - a cover, 2 - заглушка, 3 - a directing finger, 4 - a spring, 5 - brake колодки.

102 Brake system

Forward brake support (removal and installation, CB400FIIIT). 1 - перепускной a bolt, 2 - washers, 3 - фитинг, 4 - bolts of fastening of a forward support, 5 - a forward support.

Forward brake support (disassembly and assembly, CB400FIIIT). 1 - an internal part of a support, 2 - a lining, 3 · piston " А ", 4 - a dustproof cuff "А", 5 - a sealing cuff "А", 6 - piston " В ", 7 - a dustproof cuff "В", 8 - a sealing cuff "В", 9 - an external part of a support.

Brake system 103

Forward brake support (removal and installation, CB400FIIIV). 1 - шплинт, 2 - directing fingers, 3 - springs, 4 - brake колодки.

Forward brake support (removal and installation, CB400FIIIV). 1 - перепускной a bolt, 2 - washers, 3 - фитинг, 4 · bolts of fastening of a support.

104 Brake system

Forward brake support (disassembly and assembly, CB400FIIIV). 1 - piston " А ", 2 - a dustproof cuff "А", 3 - a sealing cuff "А", 4 - piston " В ", 5 - a dustproof cuff "В", 6 - a sealing cuff " In".

Honda CB400F(CB1)

Back brake колодки. 1 - a bolt of fastening of a back support, 2 - заглушка, 3 - a directing finger, 4 - brake колодка.

Brake system 105

Back brake support (removal and installation, CB400F (СВ1)). 1 - перепускной a bolt, 2 - a washer, 3 - a brake hose, 4 - a back brake support.

The main brake cylinder of a forward brake (CB400F (СВ1)). 1 · a mirror of a back kind, 2 - шарнирный a bolt of the lever of a brake, 3 - the lever of a brake, 4 - перепускной a bolt, 5 - washers, 6 - a brake hose, 7 - a socket of the switch of stoplights, 8 bolt of fastening ГТЦ, 9 - arm ГТЦ, 10 - ГГЦ.

106 Brake system

The main brake cylinder of a back brake (removal and installation, CB400F (СВ1)). 1 - перепускной a bolt, 2 · washers, 3 - фитинг, 4 - a bolt of fastening ГТЦ, 5 - bolts of fastening of a footstep, 6 - a brake hose (фитинг), 7 - ring condensation, 8 - the cartridge of a rod, 9 - ГТЦ.

The main brake cylinder of a back brake (disassembly and assembly, CB400F (СВ1)). 1 - a tip of a rod, 2 - the rubber cartridge, 3 - a lock ring, 4 - a rod, 5 - piston GTTS, 6 - a spring.

Brake system 107

Pedal of a back brake (GB400F (СВ1)). 1 - a bolt of fastening of a footstep, 2 - the cartridge, 3 - the right lock bolt, 4 - a washer, 5 - a spring of the switch of stoplights, 6 - a returnable spring of a pedal of a brake, 7 - a back footstep, 8 - a pedal of a brake.

108

System зарядки

Arrangement of components of system зарядки (CB400N.) 1 - the lock of ignition, 2 - the generator, 3 - the storage battery, 4 - a regulator of a pressure(voltage), 5 - the main safety lock(fuse) (30А).

Аккумуляторная батарея

The basic circuit of system зарядки. 1 - a socket of the generator, 2 - the generator, 3 - the storage battery, 4 - a regulator of a pressure(voltage), 5 - the main safety lock(fuse) (30А).

1 - Bolt of a cover, 2 - a wire of the negative plug, 3 - a wire of the positive plug, 4 - the storage battery.

System зарядки 109

1. Check up a pressure(voltage) on conclusions of the storage battery if it below nominal, charge the storage battery.NominalVoltage.................................................More than 12,8 В2. Check up a voltage on conclusions of the storage battery at the working engine and the included headlight of a headlight.Rated voltage(At 5000 rev/min)..........................................14,0-16,0 В

3. Check up with the help of the ammeter absence

Short circuits on weight of an electric equipment.Maximal current..................................................0,01 мА

CB400N (кОм)-\+ 1 2 3 4 5

1 - ∞ ∞ ∞2 0,5-10 - ∞ ∞ ∞3 0,5-10 ∞ - ∞ ∞4 0,5-10 ∞ ∞ - ∞5 0,7-15 0,5-10 0,5-10 0,15-10 -

CB400F (SK30SEI) (кОм)-\+ 1 2 3 4 51 - ∞ ∞ ∞ ∞2 0,5-10 - 30 - 500 30 - 500 10-2003 0,5-10 ∞ - ∞ ∞4 0,5-10 ∞ ∞ - ∞5 1 -20 0,5-10 0,5-10 0,15-10

CB400F (SH609) (кОм)-\+ 1 2 3 4 51 - ∞ ∞ ∞ ∞2 0,5-10 - 30 - 500 30 - 500 10-2003 0,5-10 30 - 500 - 30 - 500 10-2004 0,5-10 30 - 500 30 - 500 - 10-2005 1 -20 . 0,5-10 0,5-10 0,15-10 -

Regulator of a voltage (the rectifier) 2. Check up presence of a voltage of the storage battery between conclusions of a socket of rectifier (Кр) and (Б), check up presence of conductivity between a conclusion of a socket (3) and weight.

1 - Socket of the rectifier, 2 – fastening bolt,3 - a regulator of a voltage (rectifier),4 - a wire of weight.

1. Check up resistance between conclusions of the rectifier.

Conclusion "+"Conclusion"-" А L в Е

А - ∞ 3-50 ∞L ∞ - ∞ 5-100В ∞ ∞ .-Е ∞ 5-100 ∞ -

3. Check up resistance of a winding of the generator.

Nominal resistance...................................... 0,1 -1,0 Ом

110 Зарядки System

The generator. 1 – generator socket, 2 - the right cover картера, 3 – fastening bolt of a flywheel (rotor), 4 - a washer, 5 - a flywheel (a rotor of the generator), 6 - шпонка, 7 - a bolt of a posting clip, 8 – posting clip, 9 - fastening bolt статора, 10 - a socket, 11 - статор in gathering.

Arrangement of components of system зарядки (CB400F.) 1 - the generator, 2 - the main safety lock(fuse) (30А), 3 - the rectifier, 4 - the storage battery.

Ignition System

Honda CB400N

Arrangement of components of system of ignition (CB400N.) 1 - position indicator of a lateral support, 2 - ignition lock, 3 – engine switch, 4 – ignition coils, 5 – ignition modules, 6 - the storage battery, 7 - the switch of a support, 8 - the switch of prohibition of start, 9 - the breaker, 10 - a spark plug.

The basic circuit of system of ignition (CB400N.) 1 · position indicator of a lateral support, 2 - ignition lock, 3 - engine switch, 4 – ignition coil, 5 - the module of ignition, 6 - the storage battery, 7 - the switch of a support, 8 - the switch of prohibition of start, 9 - the breaker, 10 - a spark plug, 11 - coupling switch.

111

112 Ignition System

System of deenergizing of ignition1. Check up conductivity between conclusions of a socket of the switch of a support.

Conclusions Conductivity

3/Б - 3 Yes

Ж/Ч - 3 Yes

CB400N. 1 - Sockets of the ignition coil, 2 - fastening nuts of the ignition coil, 3 - fastening bolt of the ignition coil, 4 - the ignition coil; 1 and 4 cylinders, 5 - the ignition coil of 2 and 3 cylinders.

Ignition coil

2. Check up conductivity between conclusion (СЗ) of a socket of the module of ignition and weight.

Checkpoint transfer Conductivity

Neutral Yes

Except for a neutral No

CB400F. 1 - Bolts and cartridges of fastening, 2 – ignition coil.

1. Check up a pressure(voltage) between conclusions "+" ignition coils (Ж/С - coils of 1 and 4 cylinders,- С/Ж - coils of 2 and 3 cylinders) and weight.Rated Voltage..........................................................АКВ

3. Check up conductivity between a conclusion (3/Б) a socket of the module of ignition and weight.

Coupling lever Conductivity

Pressed Yes

Not pressed No

2. Include ignition and establish the switch; deenergizings of the engine in position "RUN" and about trust a pressure(voltage) on conclusions of coils of ignition (see item 1) at work of an electrostarter.NominalVoltage.................................................More than 100 В

Ignition System 113

3. Check up resistance between conclusions 2. Check up a pressure(voltage) between conclusionsCoils of ignition (B/w and Ж/С - coils 1 and 4 2- contact socket of system of ignition (С),Cylinders, B/w - С/Ж - coils of 2 and 3 cylinders). NominalRated Voltage....................................................2 - 4 Ом Voltage.........................................................More than 0,7 В

4. Check up resistance between high-voltage conclusions of the coil of ignition. Nominal resistance:

With tips...................................................23 - 27 кОмWithout tips.............................................. 13-17 кОм

Fuse1. Include ignition and establish the switch deenergizings of the engine in position "RUN" also check up a pressure(voltage) between conclusions of a socket of the module of ignition (Б/Ж - "+") and (-"-") at work electrostarter.NominalVoltage.................................................. More than 0,7 In

3. Check up resistance between conclusions of the module of ignition (Б/Ж) and (Ж). Nominal resistance:

CB400N.................................................450 - 550 ОмCB400F.................................................340 - 420 Ом

1 - Socket of the breaker (2Р), 2 - the left cover картера, 3 – fastening bolt жгута postings, 4 - a fastening bolt of the breaker, 5 - the safety cartridge, 6 - the breaker.

114 Ignition System

Arrangement of components of system of ignition (CB400FIII.) 1 – ignition lock, 2 – engine switch, 3 – ignition coil, 4 - the gauge of position throttle заслонки, 5 – ignition module, 6 - the storage battery, 7 - the switch of a support, 8 - the switch of prohibition of start, 9 - the breaker, 10 - spark plugs.

The basic circuit of system of ignition (CB400FIII.) 1 – ignition lock, 2 – engine switch, 3 – ignition coils, 4 - the gauge of position throttle заслонки, 5 - the module of ignition, 6 - the storage battery, 7 - the switch of a support, 8 - the switch of prohibition of start, 9 - the breaker, 10 - spark plugs, 11 - the main safety lock(fuse) (30А), 12 - a safety lock(fuse) (10А), 13 - the indicator of position of a support, 14-switch of coupling, 15 tachometer, 16 diode.

Honda CB400FIII

Ignition System 115

The gauge of position throttle заслонки

(CB400FIII)1. Check up resistance between conclusions (С/3)And (Ж/Кр) a socket of the module of ignition.Nominal resistance ........................................ 4-6кОм

2. Connect an ohmmeter to conclusions (Ж/С) and (Ж/Кр) and check up resistance.At moving throttle заслонки from completely open position in completely for covered.. Resistance decreasesAt moving throttle заслонки from completely closed position in completely open………. Resistance increases

3. Include ignition and check up a pressure(voltage) between conclusions (С/3) and (Ж/Кр) the gauge socket

Rated voltage...............................................4,7 - 5,3 IN

4. Check of a corner of an advancing of ignition. The note:- Check is made on прогретом the engine.- For system of ignition it is not stipulated the riversгулировка УОЗ, at his(its) discrepancy устак новленным values should check up мок дуль ignitions and the breaker.а) Remove(Take off) заглушку apertures for check of a cornerAdvancings of ignition from a cover картера.б) Establish a stroboscope on high-voltage wire of the cylinder № 1.в) Start the engine and establish frequency вракщения idling (1200ё100 rev/min).г) Check up, that in an aperture the label "F", as is visibleIt is shown in figure.The note: on flywheels of engines мотоцикклов CB400FII and CB400FIII two labels "F" in view of various value УОЗ of these models (14 ° for Fllu 16 ° for FIll) are put.

CB400FII

CB400FIIIд) If УОЗ does not correspond(meet) to norm, establish stroboscope on a wire of 4-th cylinder also repeat check. If thus УОЗ will be nominal- That system in norm.е) Check up, that at opening throttle зак слонки the label "F" is displaced " against hourArrows(Pointers).ж) Remove(Take off) a stroboscope and establish заглушки on a place.

Honda CB400F1. Check of a corner of an advancing of ignition.а) Remove(Take off) заглушку apertures for check of a corner advancings of ignition from a cover картера.б) Establish a stroboscope on high-voltageWire of the cylinder № 3.в) Start the engine and establish frequency вракщения idling (1300ё100 rev/min).г) Check up, that in an aperture the label "F", as is visibleIt is shown in figure.д) If УОЗ does not correspond(meet) to norm, establish stroboscope on a wire of 2-nd cylinder also repeat check. If thus УОЗ will be nominal

- That system in norm.

116 Ignition System

Arrangement of components of ignition system(CB400F.) 1 - the ignition lock, 2 - the indicator полокжения supports, 3 - the engine switch, 4 - the coil of ignition, 5 - the main safety lock(fuse) (30А), 6 - a safety lock(fuse) (10А), 7 - the storage battery, 8 - the ignition module, 9 - the switch of a support, 10 - the switch of prohibition of start, 11 - the breaker.

е) Check up, that at opening throttle закслонки (with the help of the screw of quantity(amount)) with увеличекнием frequencies of rotation up to 1700 rev/min the label "F" "is displaced" counter-clockwise.

1 - a label "F", 2 - adjusting labels.

ж) Remove(Take off) a stroboscope and establish заглушки on a place.

2. Removal and installation of the switch of a support.а) Disconnect a socket of a support.б) Remove(Take off) a lateral cover of the pump of a cooling liquid.в) Отверните a bolt of fastening also remove(take off) выключак тель supports.

1 - a bolt, 2 - the switch of a support.

Arrangement of components of system of start (CB400N.) 1 - the relay of a starter and the main safety

lock(fuse) (30А), 2 - the switch of a support, 3 - the switch of prohibition of start, 4 - the electric motor старктера, 5 - the switch (the gauge of deenergizing) couplings, 6 * the indicator of position of a lateral support, 7 - the lock of ignition, 8 - the switch of a starter, 9 - diodes, 10 storage battery.

The circuit of system of start (CB400N.) 1 - starter relay, 2 - the switch of a support, 3 - the switch закпрещения start, 4 - the electric motor of a starter, 5 - the switch (the gauge of deenergizing) couplings, 6 - the indicator of position of a lateral support, 7 - ignition lock, 8 - the switch of a starter, 9 - диокды, 10 - the storage battery, 11 - the indicator of the switch of prohibition of start.

117

Start system

118 Start system

The relay of a starter

1. Disconnect a socket of the relay of a starter (4Р).2. Check up presence of conductivity between вывокThe house (З/Кр - "+") a socket and weight ("-") at pressed the lever of coupling and neutral transfer of a check point.3. Check up presence of conductivity between вывокThe house (З/Кр - "-") a socket and weight ("+") at отпущенк ном the lever of coupling, transfer of a check point, except for нейк тральной, to the put forward lateral support.

4. Check up a pressure(voltage) between a conclusion (Ж/Кр- "+") a socket and weight ("-") at included зажигак нии, position "RUN" the switch of the engine andThe included starter.Rated voltage…………………………………………….. АКБ5. Remove(Take off) the relay of a starter.6. Submit a pressure(voltage) from the storage battery On conclusions (Ж/Кр - "+") and (З/Кр - "-") the relay and проверьк Those presence of conductivity between conclusions of the relay, As shown in figure.

Starter (removal and installation). 1 - bolts of fastening of a tube of a cooling liquid, 2 - a tube охлажкдающей liquids, 3 - a nut, 4 - a tip of a starter wire, 5 - fastening bolt, 6 - the plug of a wire of weight, 7 - a starter in gathering, 8 - ring condensation.

Start system 119

7. Check up presence of conductivity between вывокдами the switch of a support at its(her) various покложении.The support is removed(cleaned) .................... 3/Б - 3The support is let out(released) ....................... Ж/Ч - 3

Starter (disassembly and assembly). 1 - a coupling bolt, 2 - the plug, 3 - ring condensation, 4 - a cover on the part of a drive, 5 - ring condensation, 6 - a cover on the part of a collector, 7 - ring упклотнение, 8 - a lock washer, 9 - a washer (with a green label), 10 - a washer, 11 - adjusting washers, 12 - an anchor, 13 - a nut of the plug, 14 - a washer, 15 - a washer (with a green label), 16 - ring condensation, 17 - the block of rectifiers, 18 - a brush, 19 - статор.

120 System of Start

Муфта a starter. 1 - a socket of the breaker (2Р) (С), 2 - a bolt of fastening of a cover картера, 3 - the left cover картера, 4 - a lining, 5 - the adjusting cartridge, 6 - an adjusting bolt, 7 - a washer, 8 - a ratchet, 9 - обкгонная муфта a starter, 10 - conducted шестерня a starter, 11 - the needle bearing, 12 - обгонная муфта, 13 - a washer, 14 - an axis of the leader шестерни a starter, 15 - the leader шестерня a starter.

Start System 121

Расположение компонентов системы запуска (CB400F). 1 - выключатель сцепления, 2 - индикатор положения подставки, 3 - замок зажигания, 4 - выключатель стартера, 5 - реле стартера и главный предохранитель (30А), 6 - предохранитель (10А), 7 - аккумуляторная батарея, 8 - диод, 9 - выключа -тель подставки, 10 - выключатель запрещения запуска, 11 - стартер.

The circuit of system of start (CB400F.) 1 - coupling switch, 2 - the indicator of position of a support, 3 - ignition lock, 4 - starter switch, 5 - starter relay, 6 - the main safety lock(fuse) (30А), 7 - a safety lock(fuse) (10А), 8 - the storage battery, 9 - the diode, 10 - the switch of a support, 11 - the switch of prohibition of start, 12 - the electric motor of a starter, 13 - the indicator of the switch of prohibition of start.

122

Electric Equipment

Honda CB400N

Arrangement of elements of an electric equipment (CB400N.) 1 - the switch of a support, 2 · the switch of prohibition of start, 3 - the gauge - switch on temperature of a cooling liquid, 4 - the switch of coupling, 5 - the lock of ignition, 6 - the switch of a stoplight (a forward brake), 7 - the gauge of temperature of a cooling liquid, 8 - the gauge of pressure of oil, 9 - the switch of a stoplight (a back brake).

Headlight (1) (CB400N.) 1 - the screw, 2 - a cartridge(patron), 3 - пыльник, 4 - a lamp, 5 - рассеиватель headlights, 6 - a socket фа ры, 7 - fastening bolt of the headlight case, 8 - headlight case.

Electric equipment 123

Headlight (2).1 - a lamp, 2 - a cartridge(patron).

The of turn (2).1 - a cartridge(patron), 2 - рассеива-тель the of turn.

Turn indicator(1).1 - turn indicator, 2 – screw. Turn indicator (3).1 lamp, 2 - a cartridge(patron).

Combination of devices (removal and installation) (CB400N.) 1 - speedometer cable, 2 - sockets, 3 - fastening bolt, 4 - a combination of devices in gathering.

124 Electric equipment

Lateral support. 1 - the switch of a support, 2 - fastening bolt, 3 - a pin.

1 - a nut, 2 - the of a level of fuel, 3 - ring condensation.

The gauge of a level of fuel (СВ400 R)

Combination of devices (disassembly and assembly) (CB400N.) 1 - the screw of fastening of a back cover, 2 - a back cover, 3 - the screw of fastening of the top cover, 4 - the top cover, 5 - a clip of posting, 6 - a cartridge(patron) of a lamp of illumination, 7 - the screw, 8 - internal жгут postings, 9 - the handle of dump of day time run, 10 - the screw of fastening of a drive of a speedmeter, 11 - a drive of a speedmeter, 12 - the screw of fastening of the of a speedmeter, 13 - the of a speedmeter, 14 - the screw of fastening of the of a tachometer, 15 - the of a tachometer, 16 - a nut of fastening of an arm, 17 - an arm, 18 - the case of a combination of devices.

Electric Equipment 125

Check up resistance of the gauge at various position of a float.

Position of a float Resistance

Top 4-10 Ом

Bottom 90-100 Ом

1 - Float, 2 - the gauge.

Ignition lock(CB400N.) 1 - ignition lock socket(from the party(side) жгута wires), 2 - ignition lock socket, 3 - fastening bolt, 4 - ignition lock.

126 Electric equipment

Headlight (CB400FIII.) 1 - posting clip, 2 - fastening bolts, 3 - a headlight, 4 - a socket, 5 - пыльник, 6 - headlight lamp.

Combination of devices (CB400FIII.) 1 - speedometer cable, 2 - a socket, 3 - fastening bolts, 4 - a combination of devices in gathering.

Honda CB400FIII

Arrangement of elements of an electric equipment (CB400F.) 1 – ignition lock, 2 - temperature indicator of a cooling liquid, 3 - the switch of a stoplight (a forward brake), 4 - pressure gauge, 5 - the block of safety locks(fuses), 6 - the storage battery, 7 - the switch of a stoplight (a back stoplight), 8 - the relay of es of turn, 9 - the relay of switching-off of submission of fuel, 10 - the fuel pump, 11 - the switch of prohibition of start, 12 - the gauge - switch on temperature of a cooling liquid, 13 - the gauge of the of temperature of a cooling liquid, 14 - a sound signal, 15 - coupling switch.

Headlight (CB400F.) 1 - the screw, 2 - a cartridge(patron), 3 - пыльник, 4 - a lamp, 5 - a socket of a forward dimension, 6 - рассеи-ватель headlights, 7 - a socket, 8 - the case of a headlight.

Honda CB400F(CB1)

128 Electric Equipment

Combination of devices (CB400F.) 1 - a bolt of fastening, 2 - speedometer cable, 3 - sockets, 4 - a combination of devices.

Turn indicator. 1 - the screw, 2 - a cartridge(patron), 3 - llamas па, 4 - рассеиватель.

Разборка и сборка комбинации приборов

1 - Back cover, 2 - screws.

Stoplight. 1 - a lamp, 2 - screws, 3 - рассеиватель.1 - Cartridge(Patron), 2 - conclusions of a combination of devices, 3 - a clip, 4 - жгут postings.

1 - Speedometer, 2 - a tachometer, 3 - ring condensation, 4 - the screw of the counter of day time run.

Check of a tachometer1. At the included ignition check the presence of a voltage of the storage battery between conclusions (Ч/Кч) (+) and (3) (-) a socket of posting.

2. Disconnect a socket of the module of ignition and check up presence of conductivity between conclusions (Ж/3), as shown in figure.

1 - Socket of the ignition module, 2 - a socket (6Р,).

Removal and installation of ignition lock

1 - Ignition lock, 2 - fastening screws, 3 - a socket.

1 - Forward cover, 2 - the screw.

1 - Socket (6Р, Б), 2 - a socket (6Р, Кр).

Circuits of electric equipment

The circuit of an electric equipment 1 (0030Z-MY9H-7300.) 1 - speedometer, 2 - a lamp of illumination of a combination of devices (12В, 1,7Вт), 3 - the indicator of position of a support, 4 - the indicator of pressure of oil, 5 - the indicator of temperature, 6 - a tachometer, 7 - a lamp of illumination (12В, 1,7Вт), 8, 9 - the index of a level of fuel, 10 - the indicator of excess of allowable speed (12В, 3,4Вт), 11 - the indicator of a headlight of a headlight, 12 - the indicator of the switch of prohibition of start, 13 - the indicator of the left index of turn, 14 - the indicator of the right index of turn, 15 - the block of indicators, 16 - the gauge of the index of a level of fuel, 17 - the gauge of speed, 18 - the module of the index of temperature of a cooling liquid, 19 - the block of indicators, 20 - the module of a tachometer.

The circuit of an electric equipment 2 (0030Z-MY9-0000). 1 - the indicator of position of a support (12 В/1,7 Вт), 2 - speedometer, 3 - temperature gauge of a cooling liquid, 4 - lamps of illumination of a combination of devices (12 В/1,7 Вт), 5 - the module of a tachometer, 6 - the gauge of speed, 7 - the indicator of a headlight of a headlight, 8 - the indicator of neutral transfer (the switch of prohibition of start), 9 - the indicator of pressure маскла, 10 - the indicator of indexes of turn (right), 11 - the lock of ignition, 12 - a safety lock(fuse) (10А) (the fan of a radiator), 13 - a safety lock(fuse) (10А) (headlights), 14 - a safety lock(fuse) (10А) (combinations of devices, dimensions, a sound signal), 15 - a safety lock(fuse) (10А) (systems of ignition), 16 - the block of safety locks(fuses), 17 - temperature gauge of a cooling liquid, 18 - stoplight switch(a back brake), 19 - the electric motor of a starter, 20 - starter relay, 21 - a safety lock(fuse) (30А) (main), 22 - the storage battery (12 В/8 Ah), 23 - the relay of indexes of turn, 24 - the right back turn indicator, 25 - a stoplight and a back dimension (12В 18/5 Вт), 26 - the left back turn indicator, 27 - the generator, 28 - the rectifier, 29 - the switch of a support, 30 - oil pressure gauge, 31 - the switch of prohibition of start, 32 - the breaker, 33 - the module of ignition, 34 - the coil зажигакния, 35 - the switch of a stoplight (a forward brake), 36 - the electric motor of the fan, 37 - the gauge - switch on temperature of a cooling liquid, 38 - the diode, 39 - the switch of the engine, 40 - a sound signal, 41 - the switch of indexes of turn, light of a headlight and a sound signal, 42 - the switch of coupling, 43 - the left forward index of turn (12 In 18/5 Вт), 44 - a headlight (12В 60/55 Вт), 45 - the right forward turn indicator(12 In 18/5 Вт), 46 - ignition lock, 47 - the switch of turn indicators, 48 - the switch of a sound signal, 49 - the switch of a headlight switch, 50 - the switch of light of a headlight switch, 51 - engine switch, 52 - starter switch.

130

Circuits of an electric equipment

Circuit 2.

131

132 __________________________ Circuits of an electric equipment _____________________________________

The circuit of an electric equipment 3 (0030Z-MY9-7000).

1 - The indicator of position of a support (12 In/1,7 Вт), 2 - a speedmeter, 3 - the gauge of temperature охлаждаюкщей liquids, 4 - lamps of illumination of a combination of devices (12 In / 1,7 Вт), 5 - the module of a tachometer, 6 - the gauge of speed, 7 - the indicator of excess of the resolved(allowed) speed (12 В/4,3 Вт), 8 - the indicator of a headlight of a headlight, 9 - the indicator of neutral transfer (the switch of prohibition of start), 10 - the indicator of pressure of oil, 11 - the indicator of indexes of turn (right), 12 - the lock of ignition, 13 - a safety lock(fuse) (10А) (the fan of a radiator), 14 - a safety lock(fuse) (10А) (headlights), 15 - a safety lock(fuse) (10А) (combinations of devices, dimensions, a sound signal), 16 - a safety lock(fuse) (10А) (systems of ignition), 17 - the block of safety locks(fuses), 18 - the gauge of temperature of a cooling liquid, 19 - the switch of a stoplight (a back brake), 20 - the electric motor of a starter, 21 - the relay стартекра, 22 - a safety lock(fuse) (30А) (main), 23 - the storage battery (12 In / 8 Ah), 24 - the relay указатеклей turn, 25 - the right back index of turn, 26 - a stoplight and a back dimension (12В 18 / 5 Вт), 27 - the left back index of turn, 28 - the generator, 29 - the rectifier, 30 - the switch of a support, 31 - the gauge of pressure of oil, 32 - the switch of prohibition of start, 33 - the breaker, 34 - the diode, 35 - the module of ignition, 36 - the gauge - switch on temperature of a cooling liquid, 37 - - the electric motor of the fan, 38 - the switch of a stoplight (a forward brake), 39 - кактушка ignitions, 40 - the switch of the engine, 41 - a sound signal, 42 - the switch of indexes of turn, light of a headlight and a sound signal, 43 - the switch of coupling, 44 - the left forward index of turn (12 In 18 / 5 Вт), 45 - a headlight (12В 60 / 55 Вт), 46 - the right forward index of turn (12 In 18 / 5 Вт), 47 - ignition lock, 48 - the switch of turn indicator, 49 - the switch of a sound signal, 50 - headlight switch, 51 - the switch of light of a headlight, 52 – engine switch, 53 - starter switch.

The circuit of an electric equipment 4 (0030Z-KAF-7300).1 - The indicator of position of a support (12В 1,7Вт), 2 - speedometer, 3 - the gauge of temperature coolingliquids, 4 - a tachometer, 5 - lamps of illumination of a combination of devices (12В 1,7Вт), 6 - the module of the temperature indicator, 7 - the gauge of speed of a speedometer, 8 - the indicator of excess of the resolved(allowed) speed (12 In / 3,4 Вт), 9 - the indicator of a headlight of headlights, 10 - the indicator of the switch of prohibition of start,11 - the indicator of pressure of oil, 12 - the indicator of indexes of turn, 13 - the lock of ignition, 14 - прекдохранитель the fan of a radiator (10А), 15 - a safety lock(fuse) of a headlight (10А), 16 - a safety lock(fuse)(10А), 17 - a safety lock(fuse) of system of ignition, system зарядки and the fuel pump (10А), 18 - даткчик temperatures of a cooling liquid, 19 - the switch of a stoplight (a back brake),20 - a starter, 21 - the relay of a starter, 22 - the main safety lock(fuse) (30А), 23 - the storage battery,24 - the relay of indexes of turn, 25 - the relay of switching-off of submission of fuel, 26 - the fuel pump, 27 - праквый the back index of turn (12В 15Вт), 28 - a stoplight and a dimension (12В 23 / 8Вт), 29 - left задкний the index of turn (12В 15Вт), 30 - the generator, 31 - the rectifier, 32 - the switch of a support,33 - the gauge of pressure of oil, 34 - the switch of prohibition of start, 35 - the breaker, 36 - the diode,37 - the module of ignition, 38 - the gauge - switch on temperature of a cooling liquid, 39 - electric motor of the radiator fan, 40 - the switch of a stoplight (a forward brake), 41 – ignition coil, 42 - the combined switch, 43 - a sound signal, 44 – combined switch, 45 - coupling switch, 46 - the left forward index of turn (12В 15Вт),47 - a headlight (12В 60 / 55Вт), 48 - a forward dimension (12В 3,4Вт), 49 - the right forward index of turn(12В 15Вт), 50 - the lock of ignition, 51 - the switch of the engine, 52 - the switch of a starter, 53 – illumination switch, 54 - the switch of turn indicator, 55 - the switch of a sound signal,56 - the switch of a headlight, 57 - the switch of light of a headlight.

Circuits of an electric equipment 133

Circuit 3.

134 Circuits of an electric equipment

Circuit 4.

Content

Motor oil 4

Honda Honda

Honda The air Check

Check Honda

The air Check

Adjustment of the carburettor ................................. 42Check of the switch of a support...............................42Periodicity THAT..........................................................42

Lubricating system..................................................43Honda CB400N...........................................................43Honda CB400F (СВ1).................................................45

Cooling system........................................................46Honda CB400N..............................................................46Honda CB400F (СВ1).......................................................49

Fuel System..............................................................52Honda CB400N...........................................................52Honda CB400F(CB1).................................................56

The power(force) unit...............................................59

Symbols

Put in corresponding places the following kinds of greasings:

Engine.......................................................................61Honda CB400N..........................................................61Honda CB400F(CB1).................................................65

Coupling...................................................................69

Cranked shaft and transmission.............................74Cranked shaft. ........................................................ 75Transmission .......................................................... 77Adjustment of length приводной circuits..................79

Forward suspension bracket and steering column

..................................................................................80

Back suspension bracket ...................................... 89

Brake system...........................................................96Honda CB400N..........................................................96Honda CB400FIIIT , CB400Flllv...........................................................101

Honda CB400F (CB1)...............................................104

System зарядки ................................................... 108

System of ignition.................................................111Honda CB400N........................................................111Honda CB400FIII......................................................114Honda CB400F.........................................................115

System of start ...................................................... 117

Electric equipment.................................................122Honda CB400N........................................................122Honda CB400FIII......................................................126Honda CB400F(CB1)...............................................127

Circuits of an electric equipment ......................... 130

Contents.................................................................135

ReductionsDOHC газораспределительный

the mechanism with two in gross in the head of the cylinder block

IN Admission ЕХ ReleaseАКБ storage battery VMTTop dead point ГРМ газораспределительный mechanism GTTS the main brake cylinder Color Designation For a designation of colors of wires are used t he following reductions.

Thus the first part of a designation specifies primary colour of the wire, the second (if is present) - color of strips.Designation of sockets Example: (6Р) - 6-и.контактный a socket

Motor oil

Motor oil with молибденовыми additives

консистентная greasing

силиконовая greasing

Fixing structure for grooves

Germetic

Brake liquid

Use new details instead of being in use

Color ColorЧ White Рз PinkКр Black Ср GreyКч Red About Orange

Brown ТЗ Dark greenWITH Yellow Бц ColorlessЧ Dark blue СЗ Light green3 Green Ф Violet

Manual cb1 y cb400sf en ingles.doc

Documents

Transcript of Manual cb1 y cb400sf en ingles.doc