Make One call and Get it All. One stop shopping for the ...€¦ · Make One call and Get it All....

ALBANY STEEL & BRASS has pledged to provide the sheet metal trades with the highest qualitytools and fastening products. This is clearly shown by our involvement in SMACNA CHICAGO.

We encourage all members to patronize the suppliers who actively demonstrate their commitmentto this fine organization. We are more than just a supplier to the Sheet Metal Industry...

We are part of it !

Make One call and Get it All.One stop shopping for the Contractor

Good through June 30th, 2012. Prices are subject to change without notice.

• High quality design for added strength• Solid, one piece construction• Deep groove for positive lock to ductwall• Available with ‘LOW LEAKAGE’ damper

hardware standard• Pre-stamped knock outs on all non-dampered fittings

90° ADJUSTABLEELBOWS

HIGH EFFICIENCY TAKE-OFFS

PRESS-ON CONICALS

SPIN-IN COLLARS

PRESS-ON COLLARS

SPIN-IN CONICALS• Superior air flow characteristics• Tapered boot design for improved fit on duct• High density, double sided neoprene gasket• Quality seal at duct wall• Pre-punched holes in base for easy fastening• Available with ‘LOW LEAKAGE’ damper


• Improved air flow characteristics• High density, double sided neoprene gasket• Quality seal at duct wall• Pre-punched holes in base for easy fastening• Available with ‘LOW LEAKAGE’ damper


• Quick and Easy to install• High density, double sided neoprene gasket• No tabs to bend over• Improved seal at duct wall• Pre-punched holes in base for easy fastening• Available with ‘LOW LEAKAGE’ damper hardware standard• Pre-stamped knock outs on all non-dampered fittings

• Deep groove locking ribs forsuperior strength

• Virtually inseparable seams• Smooth, solid adjustability

• Improved air flow characteristics• Deep groove for positive lock to ductwall• Available with ‘LOW LEAKAGE’ damper

hardware standard• Pre-stamped knock outs on all

non-dampered fittings

GreenSeam® Snap Lock Pipe is a uniqueself-sealing snap lock pipe which has apre-installed gasket that seals thelongitudinal seam once snappedtogether. With increased fuel cost,GreenSeam® pipe reduces leakagewhich creates higher efficiencies leadingto lower fuel costs.

ROUND DUCT HANGERSTABBED START COLLARS• Manufactured from 20 ga. galvanized metal• Includes 1/4-20 x 1 zinc plated slotted pan

machine and hex nut, attached.• Stock sizes include 4” through 18”.

Also available in 20”, 22” and 24”.

All Ductmate Pipe and Fittings areavailable in Galvanized Steel,Stainless Steel and Aluminum

We also stockCenter StyleTake-Offs

• Available from stock 3” tall x 26 ga.6” through 20 “ diameter

• Also available from stock 6” tall x 26 ga.with dampers. Diameters 6” through 14”.

• Dampered fittings furnished with‘LOW LEAKAGE’ damper hardware standard

ROUND DAMPER BLADESwith Spring Loaded hardware

• Blade Manufactured from 24 ga G60 Galvanized Steel• Damper Blades 12" diameter and up are stiffened.• Available in sizes 4" - 20".• Includes 2 retractable Spring Bearings, Stamped Galvanized

steel washer and Handle and Die Cast Wing Nut for addedstrength and reliability.

Ductmate® is a registered trademark of Ductmate® Industries, Inc.

2” LONG STAND-OFFS• Instantly turn your standard dampered

fitting into one for use in externallywrapped applications

• Eliminates the need to stock two separatefittings.

• Handle rotates independently of sleeve• Works on all size fittings that use standard

damper hardware

Ductmate's revolutionary new self-sealing snap-lock pipe, GreenSeam+®,has a pre-installed gasket that sealsthe longitudinal seam AND thetransverse joint once snapped together.GreenSeam+® eliminates the need ofexternal sealing and taping.GreenSeam+® pipe reduces leakagewhich creates higher efficienciesleading to lower fuel costs.

Available yellow union label only.

All products

proudly made byLocal 12 Members

NEW

Albany Part Number price each

Door Size Hinge & Cam Double Cam Box Qty. < full box full box

6” x 6” ACC6-6 ACC6-6-DBL 20 $10.61 $8.88

8” x 8” ACC8-8 ACC8-8-DBL 20 $12.06 $10.10

10” x 10” ACC10-10 ACC10-10-DBL 10 $14.44 $12.09

12” x 12” ACC12-12 ACC12-12-DBL 10 $16.46 $13.79

14” x 14” ACC14-14 ACC14-14-DBL 10 $19.23 $16.10

16” x 16” ACC16-16 ACC16-16-DBL 5 $22.00 $18.43

18” x 18” ACC18-18 ACC18-18-DBL 5 $24.82 $20.79

20” x 20” ACC20-20 ACC20-20-DBL 5 $27.50 $23.03

22” x 22” ACC22-22 ACC22-22-DBL 5 $32.01 $26.81

24” x 24” ACC24-24 ACC24-24-DBL 5 $34.55 $28.94

SQUARE FRAMEINSULATED ACCESS DOORS

Tabb

ed S

tyle

Pre

ss-O

n S

tyle

SANDWICH STYLE ACCESS DOORSDoor Size Part Number Style 1-5 6 +

12” x 8” ACC12-8U UN-INSULATED $27.85 $23.33

10” x 6” ACC10-6I INSULATED $21.19 $17.75

12” x 8” ACC12-8I INSULATED $30.51 $25.55

18” x 14” ACC18-14I INSULATED $64.88 $54.34

24” x 18” ACC24-18I INSULATED (Oval) $111.22 $93.15

10” x 6” ACC10-6G 1000° GREASE $32.47 $27.20

12” x 8” ACC12-8G 1000° GREASE $46.78 $39.18

18” x 14” ACC18-14G 1000° GREASE $99.45 $83.30

10” x 6” ACC10-6H 2300° HI-TEMP $67.45 $56.49

12” x 8” ACC12-8H 2300° HI-TEMP $97.12 $81.34

18” x 14” ACC18-14H 2300° HI-TEMP $139.09 $116.50

24” x 18” ACC24-18H 2300° HI-TEMP (Oval) $260.44 $218.13

8” Diameter ACC8U ROUND UN-INSULATED $19.41 $16.25

price each

• Quick Installation. No measuring (self-adhesivecut-around template provided). No frame toinstall and seal.

• Effortless opening and closing. No toolsrequired. Conical springs and plastichand knobs make operation easy.

• Air tight seal. Due to the design and neoprenegasket.

• Reduced friction. The inside surface of thedoor is smooth.

U.L. Rated Grease Duct Doors

• UL 1978 Listed• Dramatically reduced installation time• No special tools required• Union Made in the U.S.A.• Available in a variety of sizes• Grease and air tight• Meets NFPA 96 standards• Meets all mechanical codes

Albany Part Number price each

Door Size Hinge & Cam Double Cam Box Qty. < full box full box

6” x 6” ACC6-6P ACC6-6P-DBL 20 $13.60 $11.39

8” x 8” ACC8-8P ACC8-8P-DBL 20 $14.84 $12.43

10” x 10” ACC10-10P ACC10-10P-DBL 10 $17.50 $14.65

12” x 12” ACC12-12P ACC12-12P-DBL 10 $19.37 $16.23

14” x 14” ACC14-14P ACC14-14P-DBL 10 $25.64 $21.47

16” x 16” ACC16-16P ACC16-16P-DBL 5 $29.40 $24.63

18” x 18” ACC18-18P ACC18-18P-DBL 5 $33.79 $28.30

20” x 20” ACC20-20P ACC20-20P-DBL 5 $38.17 $31.97

22” x 22” ACC22-22P ACC22-22P-DBL 5 $45.07 $37.75

24” x 24” ACC24-24P ACC24-24P-DBL 5 $46.31 $38.79

Dovetail frames are double gasketed witha closed cell neoprene gasket. Dovetailframes are available for both metal andfiberglass ductboard.

Press-On frames use a closed cell neoprenegasket for the inside of the frame and adouble sided adhesive, closed cell neoprenegasket on the outside of the frame.

Sandwich Design Weld On Design For Round Pipe

2

NEW

Provides easy access into high-temperature air ducts and grease duct systems.Designed for applications requiring UL 1978 listing.

price per cft. (combinable)part# description <1000 ft. 1000 ft. 3000 ft.

ADC28 2" x 26ga. $72.05 $69.57 $66.09hollow vane

ADC29 2" x 24ga. $86.84 $83.85 $79.66vane rail

ADC31 4" x 24ga. $144.11 $139.14 $132.18hollow vane

ADC30 4" x 22ga. $133.86 $129.24 $122.78vane rail

prices per hundredpacked 250/ctn

part # description 250 8,000 16,000

DUCTDC TDC STYLE $30.38 $26.58 $25.63

DUCTDF TDF STYLE $30.38 $26.58 $25.63

DUCTDC-AUTO* TDC STYLE $30.38 $26.58 $25.63

DUCTDC-IP** TDC STYLE $38.30 $33.51 $32.31

* for Ductmate Model 'T' Corner Inserter** stacked for Cornermatic® machines

TDC and TDFSQUARE HOLE

CORNERS

GALVANIZED CLEAT PRODUCTSprice per cft.

ADC28, ADC29, & ADC30packed 100 ft./bundleADC31 packed 50 ft. / bundle

All items sold in 10 ft. lengths / 100 ft. per bundle / full bundles onlyAll Ductmate cleat products are combinable for price advantage

Ductmate vane is compatiblewith any rail system

Albany part #

DUC6VERSA

1 ctn 20 ctns 40 ctns$23.66 $21.50 $20.80

prices per hundred pcs. / packed 250 pcs./ctn

part # description 100 ft. 1000 ft. 3000 ft. 5000 ft.

DUCDS26-10 26 ga. DRIVE SLIP $20.22 $19.50 $19.21 $18.78DUCDS24-10 24 ga. DRIVE SLIP $26.58 $25.63 $25.25 $24.68

DUCHS26-10 26 ga. HEMMED 'S' $37.90 $36.54 $36.00 $35.19DUCHS24-10 24 ga. HEMMED 'S' $41.01 $39.54 $38.96 $38.08

DUCSS26-10 26 ga. 1" STANDING 'S' $53.31 $51.40 $50.64 $49.50DUCSS24-10 24 ga. 1" STANDING 'S' $60.66 $58.49 $57.63 $56.33

Can be used in conjunction witha variety of TDC connectionsalong with Ductmate 45.

PRO Rail ™VANE and VANE RAIL

part #DUCVERSA-TOOL

DUCTMATE VERSA-CLEAT TOOL$28.63 each

****

MONOrail™

Turning Vane SystemVersatile Single Wall or Double Wall System

• Slotted for even spacing of vane

• Rigid design for reduced vibration

• No special tools are required

• Fabricated with precision equipment

• Available in specialty metals

part #ADC2

200' - 2" wide Vane Runner $104.80 each

part #ADC4

100' - 4" wide Vane Runner $72.85 each

3

VERSA-CLEAT®

DUCTCONNECTOR

• Commercial Grade, Airtight and Waterproof

• Variety of fabrics, metals, and widths

• Designed to meet NFPA 90A and 90B Specifications

• 24 gauge galvanized steel which meets ASTM-A-653-94-G60

• Fabrics meet UL 214 requirements (except Teflon®)

part # size material fold per 100 ft.box

ADC3 3" x 3" x 3" Vinyl single $115.43ADC3-DF 3" x 3" x 3" Vinyl double $103.26ADC3-NEO 3" x 3" x 3" Neoprene single $154.92ADC5 4-1/2" x 3" x 4-1/2" Vinyl single $144.25ADC5-NEO 4-1/2" x 3" x 4-1/2" Neoprene single $189.63

ADC3-SM 3 x 3 x 3 Vinyl single $115.432' x 2' carton for use with Duct Connector Dispensers

MOISTURE DRAINWhen moisture collection is a problem in ductworkor drain pan the Ductmate moisture drain is aneconomical and fast way of installing a leakproofdrain.The Ductmate moisture drain draws thesurrounding duct area into a funnel shape,assuring drainage.

$27.76 each

part #

DUC1607drain cap sold

separately

NEOPRENE DUCT FABRIC

price per c (combinable)

part # description 250 pcs. 1000 pcs.

TIE1/2-ER 1/2" DIA $64.80 $48.60TIE3/4-ER 3/4" DIA $67.60 $50.70

TIE ROD CONSTRUCTIONHARDWARE

part # description price/each

DUCEZTOOL MAGNETIC TIE ROD TOOL $50.53

A simple, strongcomponent system tomake the installation oftie rods faster. Can beused for positive ornegative pressure.

4

HARDWARE CLOTH

Hardware Cloth is a hot-dipped galvanizedscreen with a welded mesh. 19 gauge forextra durability. Heavy Zinc coatingprovides maximum protection.

1/2" x 1/2" squares x 19 ga.

part # width price each

HWC2248 48" $177.10HWC2260 60" $241.01

NEOPRENE DUCT FABRIC is the choice ofspecifying engineers. It is the industry standard,retaining its flexibility and aging characteristicsover a long period of time.

NEOPRENE offers high resistance to a broadrange of chemicals, acids and alkalis.

part # width price each

ADC1 10" WIDE x 100' ROLL $132.50

CLUTCHER

• May be used on a variety of mechanical systems• Steel Cable & Clutcher mechanism sold separately• Eliminates the need to stock pre-cut cable• Tapered bore design for fast and easy installation• Easily adjust hanging height by hand• Extremely strong patented design• Offers a 5 to 1 safety factor• Available in a variety of sizes for different load weights• Items can be hung at angles up to 60o from vertical• Lightweight design reduces the risk of on-site accidents• Aesthetically pleasing

Mechanical System Hanger

part # width price reelDUCWR10500 #10 x 500' $104.81DUCWR101000 #10 x 1000' $193.38

DUCWR20500 #20 x 500' $108.06DUCWR201000 #20 x 1000' $202.76

DUCWR30500 #30 x 500' $257.39DUCWR301000 #30 x 1000' $438.55

DUCWR40500 #40 x 500' $337.89DUCWR401000 #40 x 1000' $673.59

part # description price each

DUCCL10 #10 CLUTCHER $2.93DUCCL20 #20 CLUTCHER $3.49DUCCL30 #30 CLUTCHER $5.51DUCCL40 #40 CLUTCHER $9.93

CLUTCHER BODY

CLUTCHER STEEL CABLE

part # description price each

DUCHFWRC CLUTCHER WIRE CUTTER $39.95

MAXIMUM SAFE VERTICAL WORKING LOADS

DUCCL10: 125 lbs. DUCCL30: 650 lbs.DUCCL20: 250 lbs. DUCCL40: 1250 lbs.

SAFETY NOTE: In order to meet testing and product specifications,the Clutcher system requires that Ductmate Steel Cable be used.

10 or more...$22.21 each

Solvent Based DUCT SEALER

part # size price/case

USMGAL GALLONS $112.64USMQT QUARTS $94.10USM11 11 oz $47.43

FULL CASES ONLY

Gallons packed 4/case - Quart & 11oz. Tubes packed 12/case

WATER BASEDINSULATION ADHESIVE

part # container size price/each

USMUNI-TACK-5 5 GALLON $58.82USMUNI-TACK-52 52 GALLON $531.63

CHIP BRUSHES100% natural white bristle withwood handle

box < full fullpart # size qty. box box

BPB12-CHIP 1/2" wide 36 $0.44 $0.37BPB1-CHIP 1" wide 36 $0.56 $0.47BPB112-CHIP 1-1/2" wide 36 $0.64 $0.54BPB2-CHIP 2" wide 24 $0.84 $0.70BPB3-CHIP 3" wide 12 $1.44 $1.21BPB4-CHIP 4" wide 12 $3.20 $2.68

CAULK GUNSEconomy Grade• 5:1 Thrust Ratio• All Steel Welded Construction

part # size style price ea.

GUN77 10 oz. 1/2 barrel $3.28

Professional Grade• 10:1 Thrust Ratio

• E-Z Load Front Cap

• Ladder Hook

UNI-TACK™ Duct Liner Adhesive is an economical,water-based product for bonding insulation to metal.Can be sprayed, brushed, or rolled and is designedfor both manual and automatic applications. It providesexcellent results with easy cleanup.

Offers high-bonding strength for sure, first-time sealing of joints in low to high pressureHVAC duct systems. Its superior quality makesit suitable for indoor and outdoor use. ULListed.

part # size price/case

USMGAL-WB GALLONS $86.54USM11-WB 11 oz $35.87

Water Based DUCT SEALERSpecially formulated to seal low to high-pressure duct systemsin indoor and outdoor use. It provides excellent adhesion togalvanized metal. It contains no solvents or asbestos and it isnon-flammable and fire retardant. UL Classified.

Premium Water Based High Velocity Duct Sealant• Effective in low, medium, and high pressure systems• May be used for indoor or outdoor applications• Will not drip or sag• Mildew resistant

UL 181B-MListed

part # sizeDUCPROSEAL-G GALLONS

$73.58 per case

packed 4 gallons per case

part # size

DUCPROSEAL-T 11 oz$76.21 per case

packed 25 tubes per case

Price shown is per poundPacked 50 lbs./casepart # NAS102

FEATURES:Adheres to a variety of surfaces.Does not stain hands or painted surfaces.Can be painted.

ASBESTOS FREEDUCT SEALER

1-9 lbs. 10-49 lbs. 50 lbs +$5.55 $4.16 $3.72

price each

PROseal

SolvSealPREMIUM SOLVENT

BASED DUCT SEALER

• UL Classified• Permanently Flexible• Fast Drying• Will Not Drip or Sag• High Water Resistance• Low Brush Drag• Excellent Spreadability• Minimal Shrinkage• Indoor or Outdoor Use• Superior Sealing Strength

5

part # size style price ea.

GUN111 10 oz. skeleton $6.90GUN530 Quart skeleton $15.31

part # size case qty. price/case

DUCSOLV-G Gallons 4 $106.55DUCSOLV-T 11 oz. Tubes 24 $96.90DUCSOLV-Q Quart Tubes 10 $84.79

ALUMA GRIP™ is a Peel•N•Seal™ HEAVY DUTY pressure sensitiveduct joint sealer on a roll. It provides an aggressive water resistant gripto most surfaces including sheet metal, duct board, flex duct and ductwrap vapor barriers. THE GRAY MATTER™ butyl adhesive/sealant is100% solids so it stays supple and resists releasing.

part # description price/case

HARAFT-701-3 3" WIDE x 50' ROLL (16/CASE) $355.84

Other sizes available up to 12" wide

FOIL GRIP™ is a Peel•N•Seal™ pressure sensitive duct joint sealerand general purpose sealer on a roll. FOIL GRIP™ provides an instantwater resistant grip to most surfaces including sheet metal, duct board,flex duct and duct wrap vapor barriers. The butyl adhesive/sealant is100% solids so it stays supple and resists releasing.

Other sizes available up to 6" wide


HARAFG-1402-3 3" Wide x 100' Roll (16/case) $486.80

Price per single roll $38.20

INDOOR / OUTDOORUNDERGROUND

PRESSURE CLASS: Up to 10" W.G. PRESSURE CLASS: Up to 6" W.G.

NO BRUSHES,NO MESS, andNO WASTE

PremiumDUCT SEALER ON A ROLL

You'll find UL181 Foil Tapeon Page 8 of this catalog

SPRAY-SEAL™Mobile Duct Sealant Delivery System

• Portable Delivery System.

Out of the Shop, Into the Field.

• Substantial Labor Savings

• Increased Coverage Rate

• USDA, EPA & FDA Approved

SPRAY-SEAL™ & Sealant Delivery System

Introducing a revolutionary new duct sealingsystem exclusively from Hardcast, thepioneer in HVAC sealants! The Research &Development Team at Hardcast hasformulated the next generation of ductsealant to meet the demand for cost savingsand energy efficiency.

Please ask usabout a FREE

demonstration atyour shop or

jobsite

HAR404C Packed 25 Tubes/caseHAR404G Packed 4 Gallons/case

Sold in Full Cases Only


HAR404C 11oz TUBES $89.63HAR404G 1 GAL. BUCKETS $98.48

For High, Medium and Low Pressure Systems

SOLVENT BASED

IRON GRIP High VelocityDUCT SEALANT

The PREMIUM Water Based Duct Sealant

part # container size price each

HARIA-901-5 5 GALLON WATER BASED $58.50HARIA-901-55 55 GALLON WATER BASED $492.21

INSULATION ADHESIVE


HAR601-25 Packed 25 Tubes/caseHAR601-4 Packed 4 Gallons/case


HAR601-25 11oz TUBES $92.63HAR601-4 1 GAL. BUCKETS $121.31

COIL-TACK is a low tack, nonflammable,water based insulation adhesive engineeredfor spray or extruding coil line applications.The low viscosity, low suspended solidseliminates clogging within the adhesivedelivery system ensuring consistent operation.COIL-TACK’s exceptional coverage and easycleanup means lower application cost.

SURE GRIP High VelocityDUCT SEALANT

FLEX GRIP High VelocityDUCT SEALANT

Indoor -

Outdoor

Economy Water Based Duct Sealant


HAR550-25 Packed 25 Tubes/caseHAR550-4 Packed 4 Gallons/case


HAR550-25 11oz TUBES $79.04HAR550-4 1 GAL. BUCKETS $56.81

Indoor -

Outdoor

WATER BASED

6

Price per single roll... $27.80

7

AEROSOLMARKING PAINT

Dozens of colorsto choose from.

Sold in cases of 6 cans only

part # 1-11 cans 12-23 cans 24 or more

GVL20010 $16.30 $14.67 $13.04

part # 1 gallon 2 or more

GVL20013 $199.96 $189.96

$312

$535

BLACK FELT TIP ACTION MARKERSwith plunger tip

Valve operated and filled with ink, theACTION MARKER contains10 times the ink supply of the samesize marker filled with stuffing.

part #MRK96823$482

can

12 ormore...each

'GALVILITE' PREMIUMCOLD GALVANIZING COMPOUND

Recognized by Underwriters Labs as the equivalentto Hot-Dip Galvanized. A surface properly coatedwith ZRC/GALVILITE is protected for the same amountof time as if it were hot-dip galvanized

95%Zinc !!

each

POLYPROPYLENE PLASTICDUCT COVERSReusabl

e!

Designed to protect the entire air handling system duringconstruction. Helps prevent moisture, dirt particles, dustand debris from entering the air handling system. Juststretch the elastic band over the round branch or anyother open end. No tape, screws or nylon ties areneeded to secure the Duct Cover to the duct.

Volume pricing available.Please contact an Albany representative for details.

part number round linear price/box

RDC0610 6”-9” 16"-31" $32.40

RDC1014 10”-14” 32"-47" $38.45

RDC1418 14”-18” 48"-59" $59.18

RDC1824 18” - 24” 60"-79" $68.26

RDC2430 24” - 30” 80"-99" $83.38

RDC3038 30” - 38” 100"-119" $95.04

fits duct sizes25 per box

100 ft. rolls

part # size Price/eaCDC9X12 9' x 12' x 4 mil $5.54

SELF ADHESIVE'DUCT MASK'

• Used to improve indoor air quality byreducing exposure of duct to dust, dirt,debris and moisture when Mechanical Specificationsrequire duct opening to be covered.

• Blue tint for easy identification• Self Adhesive back makes duct protection quick and easy.

part # size Price/roll

WRP10-4 10 x 4 mil $37.59WRP12-6 12 x 6 mil $67.52WRP16-4 16 x 4 mil $60.03WRP20-6 20 x 6 mil $112.56WRP24-6R* 24 x 6 mil $117.45*Reinforced

POLY-COVERPlastic Sheeting

part # size Price/rollWRPDM224-200-BLUE 2' x 200' x 2 mil $32.00WRPDM236-200-BLUE 3' x 200' x 2 mil $43.60

Your choice...

part #CRO7007

COLD GALVANIZING COMPOUND

U.S.D.A. AcceptedCrown's Cold Galvanizing Compound is a 93% pure zinc fluidcompound that allows easy application. When applied to iron orsteel, it fuses to the surface and forms a hard, adherent flexiblecoating which stops rust by electrochemical action instantly.When scratched or pierced to the base metal, rusting isrestricted to the exposed area only - rust cannot spread.

$1061 $94812 ormore...each each

MULTI-PURPOSEBLUE POLY TARPS

with Grommets

• Grommets Every 3'• Water Proof• Tear Resistant• Mildew Resistant• Rope Reinforced• UV Treated

part # size Price/roll

CDC8X10G-BLUE 8' x 10' $6.48CDC10X12G-BLUE 10' x 12' $9.72CDC12X16G-BLUE 12' x 16' $15.57CDC16X20G-BLUE 16' x 20' $25.92

Over a dozen additional sizes availableAs large as 100' x 100' !!

UNI-STRIP™ De-galvanizing Spray, is a de-galvanizing,and lubricating spray for use on roll-forming machinesand press dies. Spray will soften, loosen, and flake offgalvanizing buildup, and daily use will keep machinesclean and lubricated.

part #USMUNI-STRIP

UNI-STRIP™

DE-GALVANIZING SPRAY

$1075 per can

12 cans or more...$860

per can

20 Fluid Oz.

Blue

12oz. Aerosol

Cans

1 GallonCans

prices shownare per

container

DCP0610 and 1014 are manufactured from .002 mil thicknessDCP1418, 1824, 2430 and 3038 are manufactured from .0025 mil thickness

UL 181 Class 1 Air Duct and is manufacturedwith a reinforced metallized polyester jacket.The UPC #036 inner core is air-tight and isdesigned for low-to-medium operatingpressures in HVAC systems.

6.0R Value

UL181 PREMIUMFOIL TAPE

• 2.3 mil Aluminum Foil - Printed• High performance acrylic adhesive• 4.8 mil total thickness

Recommended for use on UL listed fiberglassduct board and flexible duct systems UL181 FOIL-GRIP TAPE

Indoor/Outdoor Duct Sealing Rolled SealantFOIL-GRIP 1403-181BFX provides an instantwater resistant grip to most surfaces includingsheet metal, duct board, flex duct, PVC coatedduct, and duct wrap vapor barriers. Suitable forsubgrade application on PVC coated duct.

17 milThick

part # size < full case full case

NAS324-2.5-181 2-1/2" x 60 yds. $28.58 $25.53

Price per roll16 rolls/case

Price per roll

24 rolls/case

6.0R Value

INSULATED FLEX DUCT INSULATED SLEEVE

INSTALLATION TOOLS

NYLON DUCT STRAPSpart # size Price/c

NDS320-T 32" $31.68

NDS420-T 42" $61.86

NDS480-C 48" $65.34

part #NDST150-T$59.50Sold in Boxes of 500.

Also sold in bags of 25at slightly higher prices.

UN-INSULATED FLEX DUCT

Built-in wire cutter lets you finish the job you started withjust one tool! Double edged blade cleanly pierces throughouter skin and insulation. Cuts from either direction aroundentire circumference of duct. Fine honed blade is long lastingstainless steel. Wire cutter cuts hardened wire rib coil.Compound leverage, for easy wire cutting. Comfortable,non-slip vinyl gripped handles.

Features:• Built-in wire cutter• Double edged blade• Cuts from either direction• Fine honed blade

FLEXIBLE DUCT CUTTER

part #SMTFDC1

$39.96each

2" x 100 ft. Rolls

part # 1-11 rolls 12-23 rolls 24 or more

HARAFG-1403-2-181 $31.83 $25.46 $20.37

Insulation sleeve is constructed of a thickfiberglass insulation blanket sheathed in areinforced metalized polyester vapor barrierjacket and supplied in 5' lengths, with an extratwo inches of jacket length for overlap. A startercap is included in each carton.

UL 181 Class 1 Air Connector which meets therequirements of NFPA (90A & 90B). Manufacturedwith a tough triple ply duct wall construction. 25'lengths, which can be easily cut to desired length.The UPC #050 is air-tight and is designed for lowto medium operating pressures in HVAC systems.

Albany Part # Size ft/ctn. Price/ctn

FLX4IM-6 4" 25 $18.28

FLX6IM-6 6" 25 $23.98

FLX8IM-6 8" 25 $28.49

FLX10IM-6 10" 25 $35.71

FLX12IM-6 12" 25 $44.48

FLX14IM-6 14" 25 $53.81

FLX16IM-6 16" 25 $61.91

FLX18IM-6 18" 25 $72.02

FLX20IM-6 20" 25 $87.47


FLX4U 4" 100 $51.72

FLX6U 6" 25 $17.36

FLX8U 8" 25 $22.67

FLX10U 10" 25 $28.65

FLX12U 12" 25 $35.67

FLX14U 14" 25 $43.29

FLX16U 16" 25 $51.93

FLX18U 18" 25 $60.52

FLX20U 20" 25 $74.09

The industry's first and only foil tape dispenser

Removes the paper release liner and appliestape in a smooth application every time.

This patented tool saves time, increasesproduction and cuts expensive labor costs.

Available for 2” - 3” wide tape

FOIL TAPE DISPENSERNEW

FLEXIBLE DUCTELBOW SUPPORT

NEW • GREEN Product - SAVES ENERGY• Improves Airflow - Forms 90-degree

Radius Elbow• Eliminates Flex Duct Kinks and Restrictions• Install on New or Retrofit Existing Flexible

Ducts• Commercial and Residential Applications• Adjustable Design - Fits 4" - 16" Flex Duct• Made in the USA From 100% Recycled

Materials• Install at Diffusers, HVAC Equipment, &

Duct Collars• U.L. Listed

part #BRPFR-DES

1-9 pcs $4.98 ea.

10-49 pcs $4.48 ea.

50 or more $3.98 ea.


FLX4SLV-6 4" 75 $76.91

FLX6SLV-6 6" 75 $89.59

FLX8SLV-6 8" 75 $105.87

FLX10SLV-6 10" 75 $132.80

FLX12SLV-6 12" 50 $109.67

FLX14SLV-6 14" 50 $140.73

FLX16SLV-6 16" 50 $169.46

FLX18SLV-6 18" 50 $195.39

FLX20SLV-6 20" 50 $224.82

8

part # size Price/c

IPC1 12ga. x 1-1/4" $11.80IPC2 12ga. x 2" $12.40

IPC3 12ga. x 2-1/2" $12.80

IPC8 12ga. x 1-1/4" $18.05IPC9 12ga. x 2" $19.35

IPC10 12ga. x 2-1/2" $19.70

IPC11 12ga. $4.60

Butylpart # size case qty. price/case

GSK2 3/16" x 5/8" 650 ft. $105.30

Neoprene (P.S.A. one side)

part # size case qty. price/case

GSK4 1/4" x 1" 1,000 ft. $167.38GSK15 1/4" x 1-1/2" 500 ft. $339.25GSK33 1/4" x 2" 450 ft. $358.00

STEEL SEAL®

GASKETING MATERIAL

for TDC and TDF connections

INSUL-LATOR ®'AMERICAN MADE' WELD PINS

Perforated Base

1000 per box. Sold in full boxes only

INSULATION HANGERS

Sold in full cases only. Price shown is per case

Peel & Stick

Retaining Clips

part # NAS357

$1463per roll

IndustrialGrade

ProfessionalGrade

part # NAS398

DUCT TAPE

24 rolls per case. Prices based on a full case purchase.Broken cases at slightly higher prices.

$708per roll

Also available Vermiculite Coated to withstand temperaturesup to 1500 °F constant, intermittent to 2000 °F

Manufactured of texturizedfiberglass yarns, Fiberglass tapewill withstand temperatures up to1000 °F in continuous service.

part # size price/cft

GSK5 1/8" x 1" $114.28

GSK7 1/8" x 1-1/2" $175.12

FIBERGLASS GASKET TAPEfor High Temperature applications up to 1,000°

Plainstyle

Drop Warpstyle for bolted

flanges

part # size price/cft

GSK12 1/8" x 1" $107.50

GSK9 1/8" x 1-1/2" $165.43

Used to bond most lightweight materials such as metal foil, fiberglassinsulation, plastic films, paper, carpet, cloth, felt, rubber, urethaneforms, leather, cork and others.For temporary bonds: spray just one of the surfaces

to be bonded.For permanent bonds: spray both surfaces

to be bonded.

'357' SPRAY ADHESIVE

part #NASSA

19.6Fluid ounces

$995 $82912 or more...each each

Prices are based on full pail purchases.Also available in 1000 packs at slightly higher prices

MECHANICALINSULATION FASTENERS

part # Thickness Density pail qty. price/100

AWP12 1/2" All 5000 $2.83AWP34 1" 1-1/2# 5000 $3.08GWP158 2" 1-1/2# & 2# 3000 $7.56GWP200 2" 3# 3000 $7.28

Recommended Recommended

Prices are based on full pail purchases.Also available in 1000 packs at slightly higher prices

part # Length For pail qty. price/100

GRI50 .370" 1/2" insulation 5000 $5.15all densities

GRI100 .525" 1" insulation 5000 $5.871-1/2# density

GRI120 .650" 1" insulation 5000 $7.383# density

GRI110 .800" 1" insulation 5000 $9.094-1/2 & 6# density

GRI150 1.40" 2" insulation 3000 $10.081-1/2 & 2# density

Recommended Recommended

part #GRIHAMMERGripnail Magnetic Hand Hammer

$8590each

Shipped in5 gallon

weatherproofpails

Shipped in5 gallon

weatherproofpails

9

RD PRO® Butyl Architectural GradeSealant. A high Performance sealantthat is ideal for below gradeapplications and outdoor jobsrequiring a durable,watertight seal.

• Water clean-up• 10 year warranty

STRUCTURALCONSTRUCTION ADHESIVE

BACKER RODNon-Absorbant, Closed Cell Foam

HEAT RESISTANTSILICONE SEALANT

LATEX CAULKSuperior quality, multi-purposeacrylic latex caulk plus Silicone.

• Paintable• Excellent adhesion• Cured caulk is mildew resistant• Interior/exterior use• Highly flexible and durable• Water clean-up• 35 Year Durability Guarantee

Part #LATWHITE Color: White

BUTYL RUBBERSEALANT

100% SILICONERTV SEALANT

$3792case

12 tubes per case /Full Cases Only

$4176case

12 tubes per case.Sold in full cases only.

Premium, long-lasting, weather-resistant sealant made especiallyfor HVAC/R applications.Excellent adhesion, flexibility anddurability. Use on air conditioners,ducts, furnaces, water heaters,refrigerators, vents and more.Adheres well to metal and mostother building materials. Remainsflexible from -60°F to 500°F

$503tube

12 tubes per case* broken cases available at slightly higher prices

Colors:Clear, WhiteBrown, Black& Aluminum

Colors:WhiteGray

Use to partially fill large cracks,gaps and joints before applyingsealant. Use for horizontal andvertical applications.

part # size price

BKR14 1/4" $7.50BKR38 3/8" $12.70BKR12 1/2" $14.00BKR58 5/8" $17.12

Prices shown are per hundred feet and are based on a purchase of 100 feet.Smaller quantities available at slightly higher prices.

part # size price

BKR34 3/4" $23.44BKR1 1" $30.00BKR114 1-1/4" $51.54BKR112 1-1/2" $62.34

10

price per tube

part # tube size 1-11 tubes 12 or more

SBGADHESIVE-11 11 oz $3.50 $3.35SBGADHESIVE 29 oz $8.96 $8.58

Part # MTC66302

FIRESTOP SEALANTWater based, general purpose, fire-rated sealant forthrough-penetrations on both vertical and horizontalsurfaces, as well as construction joints.

$1388 $121524 ormore...each each

100% Silicone Heat Resistant RTV Sealant. Formulated with ironoxide to resist extreme heat exposure. Withstands temperaturesup to 600° F and can be used on industrial ovens, heatingelements, boilers, and more. 50 year warranty. Solvent clean up.

1 - 11 tubes $13.34 per tube

12 - 23 tubes $11.43 per tube

24 or more tubes $10.48 per tube

up to--

600°intermittent

part # RDV809-0I

Highest strength construction and structural adhesive.Bonds all types of materials including steel, aluminum,concrete, glass and wood. Color: Tan

Tensile strength: 85 tons of holding power on4' x 8' plywood sheet.

INVERTEDMARKING PAINT

Solvent-Based Inverted Marking Paint. High solids formulation.Gives the boldest, brightest and most visible markings in the industry.Fast-drying, ideal for all your surveying and marking needs.

• VOC compliant• Free of lead hazards• Convenient Spray Thru™cap

$551each

Many Colors tochoose from!

1000

CLEAR CHALK LINE SAVERNEW

$551each

• Water-Based Clear Marking Paint• Protects chalk line from wind and rain• Saves hours of rework by protecting your layout• Each can has an inverted tip for upside-down

spraying• Fast-drying formula penetrates and adheres to

hot, cold or wet surfaces• 50% wider opening with Glove Grip cap

Elastomeric, gun-grade polyurethane sealant

SONOLASTIC® NP 1™

• Bonds to most construction materials without a primer• Easy to gun and tool• One component. No mixing required• Weather resistant• Paintable• Low VOC content

Stock color: Aluminumpart #SONNP1-AL

1 - 29 tubes $6.00 ea

30 or more $5.40 ea

NEW

Available in a widevariety of colors

$6354Adjusts for making 2" to 12" holes in galvanized sheetmetal. Installs into chuck of a standard electric drill motoras small as 1/4". Uses CB mill type cutting bit.

THE "ORIGINAL MALCOHOLE CUTTER

2"-12" diameterpart #SMTHC1

part #SMTCB replacement cutter... $1076 each

part #SMTHC2Adjusts for making 2" to 20" holes in galvanized sheetmetal. Installs into chuck of a standard electric drillmotor as small as 1/4". Uses CB mill type cutting bit. each

$8090

LARGE DIAMETERHOLE CUTTER

2"-20" diameter

part #SMTCB replacement cutter... $1076 each

each

Ideal for crimping heavy 22 and 24 gaugesheet metal. Nickel plated, all steel construc-tion with red vinyl cushion grips.

3 BLADE CRIMPER

part #SMTSC3

$2887

Straight pattern cutting. Metallic grayfinish. Long life inlaid steel blades arealso replaceable.3-1/2" length of cut, 14" overall length.

14" ALUMINUM HANDLE COMBO SNIP

$3897eachpart #SMTMC14A

Slide adjustment for throat depth from 1/4" to 5/8"Also used to crimp end caps on gutters. Nickel plateand black oxide finish. Formed metal cutting jaws.

part #SMTSL2

SNAP LOCK PUNCH1/4" to 5/8" THROAT DEPTH

$2851part #SMTC4

5 blades produce a factory precisiondouble crimp that downsizes withoutdeforming. Walls stay square for a tight,leakproof connection.

5 BLADE CRIMPER

$3603

Fast and easy cutting. Makes a clean 30° 'V' shapedcut in sheet metal. 13/16" maximum throat depth.Upper cutting jaw is drop forged high impact alloysteel. Nickel plate and black oxide steel finish.

$4316

HAND NOTCHER

part #SMTN1

part #SMTSL1

SNAP LOCK PUNCH3/8" THROAT DEPTH

part #SMTSC1

Punch impression spaced 3/8" from edgeof metal. Heavy forged cutting jaw. Nickelplate and black oxide finish. Green grips.

$4800

$2153

Accurate and fast scribing. Scribes a thin accurateline time after time. Nickel plated steel body.

DIVIDERS

Fast, easy to use and lightweight.Handy lock makes tool pocket sized.Zinc plated steel. Red grips.

SINGLE CRIMPER

part # circle dia. price/ea

SMT18 32" $1444

SMT24 42" $1603

each

eacheach

each

eacheach

3" HAND SEAMER 3" OFFSET HAND SEAMER$4420each

Precise vee-notched depth graduations on jaws are in 1/4"increments. Jaws are drop forged, high impact steel. Hardenedsteel handles resist abuse. Powerful compound leveragedesign. Tool also features rust resistant nickel plating. Non-slipvinyl grips with hand stops provide added comfort and control.

$5000each

We carry many other Malco products which are not shown.Please call for a complete list of available tools.11

Works overhead orin confined areas.

part #SMTS2 part #SMTS3

$55900BOHN COMBI Strapmaster

each

part #SHAA

STRAIGHT JAWpart # size price/ea

VGP7R 7" $11.83VGP10R 10" $12.03

CURVED JAWpart # size price/ea

VGP7CR 7" $11.83VGP10CR 10" $12.03

WIRE CUTTERpart # size price/ea

VGP5WR 5" $11.49VGP10WR 10" $12.09

SHEET METAL HAMMERSpart # weight style handle price/ea

HMRTR12W 12 oz. rivet wood $14.20HMRTR16F 16 oz. rivet f/glass $18.16HMRTR21W-B 21 oz. rivet wood $36.45HMRTR21F 21 oz. tinners f/glass $39.70

4 in 1 PunchCuts, Punches, Bends

and Twists Metal forHangers, Braces and

Anchors

FOLDING RULESpart # size price/ea

LUF066 6 ft. $13.03LUF066F (inside read) 6 ft. $13.03

LUF068 8 ft. $16.65

part # size price/ea

VGP6R 6" $11.06VGP11R 11" $18.73VGP18R 18" $27.27

LOCKING C-CLAMPS

* also available from stockin 7.5 ton capacity

48" MINI BRAKE

$37967each

Make big or small fabrications on the job with this lightweightand portable tool! The versatile Mini Brake produces bends upto 135 degrees in sheet metals, including aluminum, copperand 22-gauge galvanized steel. Compact size accommodatessheet metal stock up to 4ft. wide, in any length.

part #SMTMB48A

• Bends narrow roof-flashing strips• Ideal for fabricating plenums or large transitions at the job site• Accommodates sheet metal up to 4 feet wide• Dual-direction, cam-over style keep anvil secure in any position

12part #SMTMBL Optional Mini Brake Leg Kit $8773

HVAC SNIPS

5 Tons ofPunchingPower!!

PIPE andDUCT

OFFSETSTYLE

'BABY'BULL

BULLDOG

STRAIGHTPATTERN

AVIATIONfor

STAINLESS

AVIATION


WISA12 8-1/4" $17.86WISA11 9-3/4" $19.30WISA10 11" $22.75WISW7 14-1/2" $53.47


WISW5 16-1/2" $54.17


WISM5R 9-1/4" $22.71


WISM41R 9-1/4" $26.53

part # cuts price/ea

WISM6R Left $21.41WISM7R Right $21.41


WISM1R Left $18.46WISM2R Right $18.46WISM3R Center $18.46


WISM1RS1 Left $29.75WISM2RS1 Right $29.75

ADJUSTABLE PIPE CLAMP FIXTURES

part # pipe size price/ea

ADJ50 3/4" $17.82ADJ52 1/2" $13.64ADJ56* 3/4" $20.43

America’s most popular, mostwidely-used clamp fixture design

*2-1/2” deep-reach design.Heads can be reversed to “spread” work.

WIMCO SCRIBER $1630• Made of Tempered Stainless Steel• Durable-Rust Proof• Positive Grip "U" Gauge• Instantaneous and Slip Proof• Micro adjustment of Replacement Needle• Compact, will fit any pocket part # WIMSCRIBER

Theeach

ROTO CRIMPERThe fastest, easist way to

crimp round duct!

part #SABROTO-CRIMPER

$15000each

• Attaches effortlessly to your impact driver• Crimps 26ga - 22ga without adjustment• 75% faster than manual applications

A 'Must Have' for everyHVAC sheet metal worker

NEW

part # size price ea.RSD932-14 9/32" $4.78RSD516-14 5/16" $4.95RSD38-14 3/8" $6.35RSD1332-14 13/32" $7.39RSD716-14 7/16" $8.29

RSD12-14 1/2" $9.82

RSD716-38 7/16" $9.04RSD12-38 1/2" $10.71RSD916-38 9/16" $20.80

"high speed""high speed""high speed""high speed""high speed"STUB DRILLS

REDUCED SHANK DRILLS

We stock double endstubs drills too !!

Many other sizes available from STOCK !!

part # size price eachRSD916 9/16" $15.84RSD58 5/8" $17.86RSD1116 11/16" $19.88RSD34 3/4" $21.86RSD1316 13/16" $24.34RSD78 7/8" $26.14

part # size price ea.SMD332 3/32" $1.00SMD764 7/64" $1.00SMD18 1/8" $1.00SMD964 9/64" $1.00SMD532 5/32" $1.13SMD316 3/16" $1.30SMD1364 13/64" $1.33SMD732 7/32" $1.53SMD14 1/4" $1.93SMD932 9/32" $2.08SMD516 5/16" $2.40SMD38 3/8" $3.30

SMD#11 #11 $1.55SMD#12 #12 $1.55SMD#30 #30 $1.13

3/8" Diameter Shank

1/4" Diameter Shank

1/2" SHANK DRILLS

BI-METALSAWZALL BLADES

Prices based on fullpackage purchase.Broken packages atslightly higher price.

part # length qty/pk price/pk

MET48-00-5021 6" 5 14.85MET48-00-8021 6" 25 $65.00

MET48-00-5026 9" 5 $19.45MET48-00-8026 9" 25 $85.07

MET48-00-5027 12" 5 $22.40

part # size price/pkMET48-00-5712 6" x 10 tooth $14.00MET48-00-5782 6" x 14 tooth $14.00MET48-00-5784 6" x 18 tooth $14.00

MET48-00-5713 9" x 10 tooth $18.55MET48-00-5787 9" x 14 tooth $18.55MET48-00-5788 9" x 18 tooth $18.55

MET48-00-5789 12" x 18 tooth $21.35

The AX blade is designed for the toughest cuttingapplications in wood and nail embedded wood.

The 'AX' WOOD CUTTINGDEMOLITION BLADES

The TORCH blade is designed for demolition, plumbing,remodeling or general metal cutting applications

The 'TORCH' METAL CUTTINGDEMOLITION BLADES

• Cut pipe, conduit, angle iron, steel and other hard materials.• 1 inch tall for straight, fast cutting, and 0.042 inch thick for longer life• Unique heat treating process that extends the life of the blades.

• Sloped shape for superior plunge cutting for demolition and remodeling work• 1 inch tall for straight, fast cutting, and extra thick, 0.062 inch, to prevent bending• Unique heat treating process extends life• Bi-metal construction prevents shattering.

5 perpack

Holemaking – faster and easier than with conventional twist drills andhole saws – in sheet metal, plate materials, and plastics up to 1/4” thick.RotaCut™ Cutters are precision-ground and produce clean, burr-free,round holes without deforming the surrounding material. For use in handheld drills. Lasts 10x longer and cuts 3x faster than twist drills or hole saws.

part #HGN110755/16"-3/4" RotaCutTM

Sheet Metal Cutter Kit

Plastic tool case contains 11088 Arbor Assembly, Center Punch,extra Pilot, and (7) Cutters (5/16", 3/8", 7/16", 1/2", 9/16", 5/8" & 3/4")

$8750each

part # length T.P.I. qty./pk price/pk

MET48-00-1180 4" 10 10 $15.30MET48-00-1181 4" 14 10 $15.30MET48-00-5183 4" 18 5 $7.42MET48-00-5185 4" 24 5 $7.42

MET48-00-5282 6" 14 5 $9.17MET48-00-5284 6" 18 5 $9.17MET48-00-5186 6" 24 5 $10.15

MET48-00-5188 9" 18 5 $12.39

MET48-00-5189 12" 18 5 $15.47

Impact ReadyHOLE SAWS

part # size each

HSW34-DW-IMP 3/4" $14.70HSW78-DW-IMP 7/8" $15.12HSW1-DW-IMP 1" $15.36HSW1-18-DW-IMP 1-1/8" $16.60HSW1-14-DW-IMP 1-1/4" $17.68HSW1-38-DW-IMP 1-3/8" $18.60HSW1-12-DW-IMP 1-1/2" $18.80

Features:• Optimized Tooth Geometry for Faster Drilling Speeds• Impact Rated for Increased Durability

Fits Directly IntoYour CordlessImpact Driver!

13

Diamond GritDRILL BITS

part # size each

DEWDW5570 3/16" $18.66DEWDW5572 1/4" $14.40DEWDW5574 5/16" $14.64DEWDW5576 3/8" $15.80DEWDW5578 1/2" $16.84DEWDW5580 5/8" $17.72DEWDW5582 3/4" $17.92DEWDW5584 1" $17.92

• Diamond Welded Tip for Greater life and Durability• Reverse Spiral Thread Delivers Continuous Water

Feed for Longer Life and Increased Speed• Core Ejection Slot For Easy Plug Removal

For... • Marble• Tile• Glass

NEW

part #DEWD180005

14 pc. Master KitIncludes: 3/4", 7/8",1", 1-1/8", 1-3/8", 1-1/2",1-3/4", 2", 2-1/8", 2-1/4",2-1/2", Small Quick ChangeMandrel,Large Quick ChangeMandrel, Replacement Parts, Carrying Case

part #DEWD180002

9 pc. Electrician's KitIncludes: 7/8", 1-1/8", 1-3/8",1-3/4", 2", 2-1/2",Small Quick Change Mandrel,Large Quick Change Mandrel,Replacement Parts, Carrying Case

part #DEWD180001

9 pc. Plumber's KitIncludes: 3/4", 7/8", 1-1/8",1-1/2", 1-3/4", 2-1/4",Small Quick Change Mandrel,Large Quick Change Mandrel,Replacement Parts, Carrying Case

part # size price each

HSW916 9/16" $14.10HSW58 5/8" $10.60HSW1116 11/16" $10.60HSW34 3/4" $10.60HSW1316 13/16" $10.60HSW78 7/8" $10.60HSW1516 15/16" $10.60HSW1 1" $11.10HSW1-116 1-1/16" $11.10HSW1-18 1-1/8" $11.10HSW1-316 1-3/16" $11.10HSW1-14 1-1/4" $11.25HSW1-516 1-5/16" $11.25HSW1-38 1-3/8" $12.05HSW1-716 1-7/16" $12.05HSW1-12 1-1/2" $12.05HSW1-916 1-9/16" $12.05HSW1-58 1-5/8" $12.05HSW1-34 1-3/4" $14.80HSW1-78 1-7/8" $14.80


HSW2 2" $14.80HSW2-116 2-1/16" $18.40HSW2-18 2-1/8" $18.40HSW2-14 2-1/4" $18.40HSW2-516 2-5/16" $18.40HSW2-38 2-3/8" $18.40HSW2-12 2-1/2" $19.70HSW2-916 2-9/16" $19.70HSW2-58 2-5/8" $19.70HSW2-34 2-3/4" $19.70HSW2-78 2-7/8" $19.70HSW3 3" $20.25HSW3-18 3-1/8" $20.25HSW3-14 3-1/4" $20.25HSW3-38 3-3/8" $20.25HSW3-12 3-1/2" $20.25HSW3-58 3-5/8" $23.95HSW3-34 3-3/4" $28.10HSW3-78 3-7/8" $29.55HSW4 4" $30.85HSW4-18 4-1/8" $33.75HSW4-14 4-1/4" $43.90HSW4-38 4-3/8" $52.30HSW4-12 4-1/2" $60.75HSW4-34 4-3/4" $67.50HSW5 5" $74.85HSW5-12 5-1/2" $89.25HSW6 6" $104.60

VARIABLE PITCH COBALT STEELBI-METAL HOLE SAWS

part # description

BSBPB1014-BM 10/14 x 44-7/8"BSBPB1418-BM 14/18 x 44-7/8"BSBPB2024-BM 20/24 x 44-7/8"

$975blade

packed 3 blades per box. Sold in full boxes only

Lenox Vari-Bits® feature high speed steelconstruction and steam oxide coating. Apatented design two cutting flutes allow forclean burr-free holes. These bits will cutthrough materials faster than standard bits,including stainless steel up to 1/8'' thick.

Vari-Bit ®

STEP DRILLS

part # size price ea.

LNXVB1 1/8" to 1/2" $32.52LNXVB2 1/2" to 1" $56.64LNXVB3 1/4" to 3/4" $49.68LNXVB8 3/16" to 7/8" $63.52LNXVB11 7/8" to 1-1/8" $76.04

BI-METAL PORTABLEBAND SAW BLADES

your choice...

BI-METAL RECIP SAW BLADES

Part # Description Qty/Pack Price/PackMRSM424T05-XTL 4” x 24 Tooth 5 $8.42

MRSM614T05-XTL 6” x 14 Tooth 5 $10.62MRSM614T50-XTL 6” x 14 Tooth 50 $92.57

MRSM618T05-XTL 6” x 18 Tooth 5 $10.62MRSM618T25-XTL 6” x 18 Tooth 25 $49.67MRSM618T50-XTL 6” x 18 Tooth 50 $92.57

MRSM624T05-XTL 6” x 24 Tooth 5 $10.62

MRSM65006T50-XTL 6” x 6 Tooth 50 $116.90


MRSM81014T05-XTL 8” x 10/14 Tooth 5 $16.25


MRSM125006T05 12” x 6 Tooth 5 $23.21

MRSRB65006T05 6” x 6 Tooth 5 $13.31MRSRB95006T05 9” x 6 Tooth 5 $18.54

Metal Cutting

Wood Cutting

Demolition Blades (.050 thick)

14

HOLE SAW KITS

$8059ea.

$8059ea.

$13382ea.

$13500each

• Blades can be rotated 4 x 90 degrees for new sharp edge• Lock-on/off switch for extended use applications• Steel deflector for hand protection• Compact design and low vibration for maximum operator comfort• Visible blade allows precise pattern cutting and extends blade life• Sealed switch and epoxy coated field windings• Double insulated, UL listed, complies to OSHA

BOS1500C16 Gauge Shear - 4.2 amp, 5,000 SPM

$32900each

DOUBLE CUT SHEAR16 Gauge

• No tools needed to change cutters• Easy-to-replace cutter blades• Optimum cutting clearance setthrough choice of correct cutter

• Distortion-free cutting,no refinishing necessary part #TRF160

$38400ea.

MET6509-3112 amp SAWZALL® with Case

MTBW8115Q4 1/2" - 8 Amp Angle Grinder

• 10,000 rpm• Switch with lock on capability• Spindle lockTool-less guard adjustment• 2-position side handle• QUICK wheel change system• Safety slip clutchWinding protection grid

$13600each

Buy 100 Grinding or Cut-Offwheels and get the grinder for...

Buy 200 Grinding or Cut-Offwheels and get the grinder for...

$89$49or...

$36900

part # MOT5200

each

15

12 Volt MAXLITHIUM ION SYSTEM

DEWDCF610S21/4" Screwdriver KitIncludes:2 batteries1 charger1 bag

$139

DEWDCF815S21/4" Impact Driver KitIncludes:2 batteries1 charger1 bag

$159

DEWDCD710S23/8" Drill Driver KitIncludes:2 batteries1 charger1 bag

$159

DEWDCF813S23/8" Impact Wrench KitIncludes:2 batteries1 charger1 bag

$159

DEWDCT414S1InfraredThermometer KitIncludes:1 battery1 charger1 case

$149

DEWDCT410S117mm InspectionCamera KitIncludes:1 battery1 charger1 case

$299

DEWDCK211S212V MAX Drill/DriverImpact Driver Combo KitIncludes: 2 batteries, charger & bag

DEWDCK210S212V MAX ScrewdriverImpact Driver Combo KitIncludes: 2 batteries, charger & bag

$199 $199

• Powerful12 Amp Motor: Delivers 0-3,000 SPMfor high performance cutting in a variety of materials

• 3/4" Stroke Length: Provides maximum cut control• Gear Protecting Clutch: Extends gear and motor life• Counter Weighted Mechanism: Provides reduced vibration• QUIK-LOK™ Blade Clamp: Provides fast , tool-free blade changes

• "HEAVY-DUTY" performance. Effectiverange of 30 to 18 gauge sheet metal, withmore than enough power to meet your mostdemanding applications.

• Crafted of 100% TOOL STEEL assuringyears of trouble free performance.

• UNSURPASSED SPEED helps cut your bigjobs down to size. Saves time and money byreducing labor cost.

PNEUMATIC"PITTSBURGH LOCK"

HAMMER

20 Volt MAXLITHIUM ION SYSTEM

We carry the entire line ofDeWalt 20 Volt MAX tools including tool kits

DEWDCD985L220V MAX Hammerdrill/Driver Kit

DEWDCD980L220V MAX 3-Speed Drill/Driver Kit

DEWDCF885L220V MAX 1/4" Impact Driver Kit

• All-metal 3-Speed Trans for fastapplication and improved run time

• ½" Metal Ratcheting chuck for superior bit retention• LED Light with 20 second delay after trigger release

$299

$279

$269

• All-metal 3-Speed Transmission for fastapplication and improved run time

• ½" Metal Ratcheting chuck for superior bit retention• LED Light with 20 second delay after trigger release

• Compact, lightweight (just 3.4 lbs) designfits into tight areas

• Three (3) LED lights with 20 second delay after triggerrelease, provide visibility without shadows

• One-handed loading 1/4" hex chuck accepts 1" bit tips

All DeWalt 20 Volt MAX tools shown hereinclude 2 Batteries, Charger and Kitbox

PORTABLECUT-OFF MACHINES


STHTS410-12 12" $82900

STHTS420-14 14" $86900

We stock a complete line ofDiamond and Abrasive bladesfor your portable Cut-Off saws.

Stihl 2.6 oz.2-Cycle oil$3.69 ea.

METAL CUTTINGCIRCULAR SAWS

$519each

MRSCSM14B14" Metal Cutting Chop Saw with BladeMRSCSM9MB

9" Metal Cutting Circular Saw with Blade

$469each

$289each

MRSCSM7MB7" Metal Cutting Circular Saw with Blade

part #SKLHD777-1/4" Worm Drive Skilsaw™

• 22 amp switch and heavy gauge cord• Patented anti-snag lower guard reduces snags when making

narrow cut-offs• Precision-machined, durable worm drive gears for longer tool life• Push button spindle lock for easy blade changes

$149each

part #CSB714-24-58U-C7-1/4 x 24T Carbide Tipped Combination Blade

$699each

STIHL Cutquik® Cut-Off machines help youwork longer and more comfortably, deliveringa unique blend of performance andefficiency so you get the job done right.With the revolutionary "X2 Air FiltrationSystem", an anti-vibration system, and alightweight design, you get low maintenanceand more maneuverability.

part # MOT5400

$66700

Designed specifically forclosing the Pittsburgh Lock.This tool breezes along at aspeed of 15 feet per minute oncommonly used gauges.

Heavy-Duty Electric"PITTSBURGH LOCK" HAMMER PORTABLE "PITTSBURGH LOCK" MACHINE

part # MOT2400 (cart not included)

Capacity: 24 to 28 gauge material.Speed: 35 fpm.Motor: Energy efficient, 1/2 H.P.Housing: Heavy gauge, spot weldedsteel enclosure with a primed andbaked-on enamel finish.

$2,09500each

each 16

$369each

$265each

part #PLS180

PALM LASER INTERIOR-EXTERIORHORIZONTAL-VERTICAL LAYOUT

CONSTRUCTION LASERS

part #PLS3

PLUMB AND LEVEL POINT-TO-POINTALIGNMENT LASER

• The PLS180 has the longest length of line and fan angles in the industry.• Fast, accurate and portable, this plumb, level, and square laser line tool will make

your bubble vial level or rotary laser obsolete.• Exclusive PLS SLD Detector expands the utility of the PLS180 to exterior use.• Weighs less than 10 ounces, and has a self-leveling range of 6 degrees.• Operates on 3 AA batteries for over 30 hours.• Comes complete with carrying case, wall bracket, PLS180 pouch,

batteries, & operating manual. Also includes a SLD laser detector.

• Point-to-point, indoor and outdoor alignment information quickly andeasily. Does not omit lines; only points.

• Perfect for HVAC, electrical contractors and industrial technicians.Drastically reduces layout time for walls, fixtures, pipe, conduit, doorand window frames, etc.

• Self-leveling to 6 degrees, accurate to +/- 1/4 inch at +/- 100 feet.Compact, durable, and just 12 ounces.

• The PLS3 Laser Tool includes the carrying pouch, floor stand, &magnetic wall bracket.

We carry many other PLS laser alignment tools.

NEW!

18” x 30” Frame with carpet covered endsand 3” hard rubber casters

• 1000# capacity• 1-3/8” thick oak frame

Albany part #FAI3518Q-2754RT

Albany part #FAIC72-IRBAlbany part #FAIC118-8

Features 1" steel tubing, all welded construction,curved cross pieces with center strap and steel foldednose plate. Stair climber welded to axle plate and noseplate for added rigidity. Built for rugged service.

ALL STEEL HAND TRUCK

800 lb Capacity !!

LEVER TRUCK

We'll Stencil Your Company Name... "FREE"

Provide the mechanical advantage of great leverage for liftingheavy cases, crates, machinery, die blocks and other heavyunits. Seasoned oak handle, rounded and smoothed. Heavyduty beveled nose iron attached to oak handle withcountersunk bolts. 6" x 9" plate projects 3 inches.

$27344

Albany part #FAIT1116-3HR

27” x 54” Tongue and GrooveHardwood Platform Truck• Top of the line 8” mold-on

rubber wheels• Durable epoxy coat finish

$5930

$16519each

$9813

GENUINE OAK DOLLY HARDWOOD PLATFORM TRUCK

DRYWALL CART with Inset

• Inset back tube frame for turning tightcorners, moving through doorways

• Four swivel casters with optionalposition locks

• 8" polypropylene casters• Platform 12" x 43-5/8"• 47" H x 49-3/4" L x 25" W

part # DWCDC2024-INSET$42975

each

HEAVY DUTY UTILITY CART

part #RBMRCP4520BEI

• Sturdy, structural foam constructionwon’t rust, dent, chip or peel.

• Rounded corners protect walls and furniture.• Lightweight and maneuverable.• Large, non-marking casters.• Optional middle shelf available.

L: 45 1/4 in. W: 25 7/8 in. H: 33 1/4 in.

$19990

Perfect for transporting equipment andheavy loads in any environment.

each

3,000 lb.Capacity

STANCHION PLATFORM TRUCKPerfect for moving andstoring long, bulky items ofroll goods, pipe and lumber

• Removable, heavy-duty steelcorner posts provide easy access

• Corner posts retainer clipsprevent unintended removal

• Duramold™ precision engineeredresin and metal compositestructure for unsurpasseddurability and service life

• Molded-in tie-down slots• Textured deck surface reduces

slippage• Powder coated steel handle and

frame for optimum service life• 2 fixed, 2 swivel casters for

optimal control & maneuverabilitypart #RBM4481

$39550each

17

each

each

each

Laminated Body

PADLOCKS

Available with extra length shackles

body shackle shackle keyed keyedwidth diameter length different alike

No. 3 1-9/16" 9/32" 3" $8.80 $9.64

No. 5 2" 3/8" 1" $12.80 $13.64

• 4-pin cylinder helps prevent picking• Hardened boron alloy shackle for superior cut

resistance• Dual locking levers provide extra pry resistance• Thousands of key changes maximize key integrity• Proprietary rustproofing for longer life

JOBMASTER®

CHESTS

STORAGEMASTER®

CHESTS

Dimensionspart # Inches ( LxHxW) Price/ea

KNA32 32 x 13 x 19 $320.45

KNA36 36 x 16 x 19 $335.75

KNA42 42 x 18 x 19 $378.25

KNA4824 48 x 23 x 24 $466.65

KNA4830 48 x 29 x 30 $555.90

KNA60 60 x 23 x 24 $558.45

Dimensionspart # Inches (LxHxW) Price/ea

KNA69 60 x 34 x 30 $827.90

KNA79 48 x 46 x 30 $876.35

KNA89 60 x 46 x 30 $880.60

• WATCHMAN® IV Lock System with 3-pointlatching and recessed lock.

• Power Pass™ electrical pass-through grommetfor easy weatherproof power cord access.

• Heavy-duty hinges are staked and welded tostand up to any amount of prying.

• Recessed handles for positive gripping evenwith a gloved hand.

• Baked-on enamel finish for weather resistanceand durability.

• Heavy-duty 16-gauge steel construction withfully arc-welded seams.

We'll Install Padlocks,Mount Casters

AndStencil Your Boxes

FREE

NEWErgonomic

Design

HEARING PROTECTION

• Molded with soft, siliconerubber for all day comfort

• Triple flanged designcreates three barriers ofnoise blocks

• Washable and re-usable

• Smooth, tapered shapeallows for easy insertion

• Molded from soft foamprovides all day comfort

• Foam slowly expands toshape for a comfort fit

Reusable Ear Plug with Neck CordSoft Foam

Disposable Earplugs Padded foam headband andsuper- soft cushions deliverlong wearing comfort, togetherwith telescopic heightadjustment, offers maximumprotection from an Earmuff.

Ear Muffs

$5250BOX $210

each200 per box part # WSPEP300

part # WSP365$1640

eachpart # EAS513

part #3-M8210

3M DUST & MIST RESPIRATORDisposable N95 Respirator, Two Strapswith Foam Nose Bridge for Comfort

HARNESS andLANYARD KIT

with BAG

part # SAF30502

Kit includes...

• Lightweight, Large/X-Largefull-body harness with backD-ring.

• Grommet leg straps foradded support.

• 6' shock absorbing lanyard$11900each

WHITE HARD HATwith Ratchet Suspension

$1685each

part #SAFHAT-W-R

Includes FREECarrying Bag

Our top-selling hard hat features aneasy-to-use, fast-to-adjust ratchetsuspension. Lightweight, ruggedpolyethylene hard hat shell, that isbalanced on the head by the continuousloop nylon fabric suspension straps.

• Blue quilted nylon shell with fastener straps• Three layers of thick foam

DELUXE WINTER LINER

Made from the most technologicallyadvanced fabrics that combine thebest of performance and comfort.

part #EAS524

$450each

part #AAS2N1-BO

LONG WINTER LINER• Great coverage reduces drafting• Top section: fleece with elastic around face;bottom section: spun polyester $695

each

Thermal winter liner gives workersfull protection from the elements.

25 PERSON FIRST AID KIT

$2936each

part #EAS325

ABC DRY CHEMFIRE EXTINGUISHERManufactured from lightweight aluminum withtough metal valve. fitted with a pressuregauge that provides 'at-a-glance' status.

part # net agent wt. price each

PYR10 10# $92.66 Rechargeable!!

3 PIECE PVC COATED RAINSUITS


EAS117-M Medium $14.52EAS117-L Large $14.52EAS117-XL X-Large $14.52EAS117-XXL XX-Large $15.96

Includes: Jacket with Snap-On HoodBib Overalls with Elastic in Suspenders

GLASSES and GOGGLES

part #SAFGLASS-CLRClear Safety Glasses

part #EAS432Clear Ventilated Safety Goggle

$639each

$350each

DRYBROWSWEATBANDKeep cool and preventperspiration from runninginto your eyes in hot,humid conditions

part #EAS338

$0.60 each

18

CAUTION TAPE3" wide x 1,000'

part #TPE331000Y-CAUT

$1196each

COMPLETE FACE SHIELD

part #SAFSHIELD

• 16" x 8" Polycarbonate Lens• Spark deflector for added protection• Comfortable padded sweatband• Adjustable headgear fits a variety

of head sizes

$1975each

$26.20 per box

8 boxes or more... $20.96 per box

Includes:1 x 3 Adhesive Strips, 4" Gauze Pads,Large Wound Pads, 1/2" Adhesive Tape, 4" GauzeBandage, Triangular Bandage, Antiseptic Wipes,First Aid/Burn Cream, Aspirin, 1 oz.Eye Flush, Eye Pads,Eye Cup, Instant Cold Pack, Elastic Bandage, LatexGloves, Scissors, Forceps.Case Material: Weatherproof Plastic

Packed 20/box

SAFETY VESTSHigh Visibility/Class 2

Closure: Zipper and Pockets2” silver tape reflective material.1 horizontal stripe. Contrasting trim detailColors: Hi-Viz Green or Hi-Viz Orange

MountingBracket

Included!

part #SAFVEST-XL-LIME

part #SAFVEST-XL-OR

$1469ea.

12 or more...$1371

ea.

NEW


CRD14-3-25-TL 14-3 x 25 ft. $30.53CRD14-3-50-TL 14-3 x 50 ft. $50.85

TROUBLE LIGHTS

QUADNECTOR POWER CORDS


CRD14-3-50-LE 14-3 x 50' $36.27CRD14-3-100-LE 14-3 x 100' $65.64CRD12-3-25-LE 12-3 x 25' $32.07CRD12-3-50-LE 12-3 x 50' $54.18CRD12-3-100-LE 12-3 x 100' $97.57

POLAR/SOLAR PLUS®

Super flexible power cords withPOWER INDICATOR LIGHT

• All-purpose outdoor extension cord that staysflexible to -67° F

• Resistant to oils, grease, and chemicals as well asflame, water, sunlight, weather, tears, and punctures

• UL listed for outdoor use and meets OSHA requirements.

Versatile multi-use utility lamps withpolished and vented aluminum reflector

• 18/2 x 15' cord with 8-1/2" reflector• UL listed• double ball universal joint,

non-marring grips and a clamp-on bracket• On-off push through switch and

rugged molded-on plug.

REFLECTOR LIGHTS

• Resistant to oils and chemicals• 2-1/2 times abrasion resistance• Stays flexible to -67° F

part #CRD12-3-100-QD each

12-3 x 100 ft.

The versatility of 4 way power combined withthe rugged durability of a polar/solar cord

$9813part #CRD18-2-15-RL

15 amp GROUND FAULTINTERRUPTERS

$2595each

part #CRD12-3-2-GFI-TRI

12-3 x 2' TRI-TAP GFCI

• UL listed and meets OSHA specifications• Made of 3-conductor, 12-gauge wire and

with Polar/Solar jacket.• molded Tri-Source 3-way power block

with outlet covers for unused outlets.• Rainproof, rated at 15-amp with test and

reset buttons

$2761each

3 WAY ADAPTER$795

each

EXTENSION CORDCOLOR CODING TAPE

part # color

NASA7-BLUE BLUE

NASA7-GREEN GREEN

NASA7-ORANGE ORANGE

NASA7-RED RED

NASA7-WHITE WHITE

NASA7-YELLOW YELLOW

3/4" x 60' Electrical Tape

Your choice... $3.29 each

OSHA requires periodic testingand color coded marking of allextension and power cords.

part #ECI09906

HALOGENWORK LIGHTS

2 in 1 Feature

6 ft. Tripod Lights

• Heavy Duty Face Frames• Insulated Foam Handles• Tripod Extends to 6ft.• On/Off switch• 5 ft. cord• Includes 2 in1 feature• Bulbs Included

part #

VLT08-00210part #

VLT08-00611

2 in 1 Feature

each$4014

each$6026

each$2012

part #DMCSB-2000Replacement 500 Watt Quartz Bulb

$1020each

part #VLT08-00314Optional Single HalogenBase Magnet for Model #VLT08-00609

$900each

COMPCOMPCOMPCOMPCOMPAREAREAREAREAREQUALITQUALITQUALITQUALITQUALITYYYYYTH

ETH

ETH

ETH

ETH

E

500watt

1000watt

500watt

part #

VLT08-00609• Heavy Duty Face Frame• Insulated Foam Handle• 3 ft. cord• Bulb Included19

Used to indent several thick-nesses of metal, forming a 3/8"dia. button or dimple that holdsthe pieces together securely.

part #R/W8#8 5 TONMEDIUM DUTY PUNCHwith 9/32 Punch & Die

part #R/W9#9 UNIVERSALBUTTON PUNCH

part #R/W7A#7A 2-1/2 TONMEDIUM DUTY PUNCHwith 7/32 Punch & Die

Quality Sheet Metal Fabricating Equipment Since 1910

$30000each

$40000each

$53000each

$8600each

part #R/W5JR#5 JR. PUNCH W/CASEIncludes tool, and one 3/32", 1/8",5/32", 3/16", 7/32", 1/4", and 9/32"round punch and die, and plastic box

Part # Size Price Each

LAD4F 4 ft. $78.43LAD6F 6 ft. $101.62LAD8F 8 ft. $137.87LAD10F 10 ft. $205.30LAD12F 12 ft. $251.63

Step Ladders

• Da BootTM Polypropylene copolymerboot provides strength, durabilityand fiberglass rail surface protection.

• Molded Top with Tool Slots• Double-rivet step construction• Full channel fiberglass rail

** LAD36F and LAD40FRated 250 lbs.

We'll stencil 'em at “NO CHARGE”

• Promote your company name with the LogoLock™ system• Deter Theft by displaying your logo• Customize the image of your ladders• Long lasting image embedded into the fiberglass rail

Part # Size Price Each

LAD20F 20 ft. $227.31LAD24F 24 ft. $263.63LAD28F 28 ft. $311.76LAD32F 32 ft. $388.67LAD36F** 36 ft. $421.76LAD40F** 40 ft. $495.63

Extension Ladders

• Patented QuickLatch® on rung locks• Swivel safety shoes• Outside slide guides• D-Shaped Rungs• Mar-resistant rail end caps

Or, ask about...

SCAFFOLDINGby...

STEP-UP WORKSTANDS

$22800each

$32300each

$34300each

part #PERSU44 ft. STEP-UP WORKSTANDH 51-1/2” x L 48” x W 22”Load Capacity: 500 lbs.

part #PERSU55 ft. STEP-UP WORKSTANDH 60” x L 56” x W 25”Load Capacity: 600 lbs.

part #PERSU66 ft. STEP-UP WORKSTANDH 72” x L 56” x W 25”Load Capacity: 600 lbs.

3 Versatile tools for the price of one!

The Step-Up Scaffold sets up inseconds and works as a miniscaffold, a materials cart and awork stand. With the optional steelpaint shelf, a standard roller paint trayclips on perfectly for addedconvenience.

• Two 14 gauge Steel Platforms• Four 5” All Brake Casters• Folds flat for easy storage and

transport

part #PER460WPIC56' Long, 43" High49" H x 74"L x 29.5" WLoad Capacity: 1,000 lbs.

$37800each

NEW

NEW

part #PER660WPIC56' Long, 6' High78" H x 74"L x 29.5" WLoad Capacity: 1,000 lbs.

$39900each

part #PER680WPIC58' Long, 6' High78" H x 98"L x 29.5" WLoad Capacity: 1,000 lbs.

$45900each

All units furnished with 5"Swivel Lockable Casters

• One Person can assemble a basic sectionin less than a minute without tools

• Adjusts in seconds! Platform heights areadjustable in 4" increments

• Perry Scaffolds are great for stairs20

PROOF COIL CHAIN

MATERIAL LIFTS

part #SUM2412• 400 lb lifting capacity up

to 12 feet high• A Super compact 12' Lift• One piece construction -

no loose parts ortelescoping masts

• Extremely portable for oneman operation

• Fits in most vans and SUVs

$1433 each

2100 Series Lifts• 650 lb. capacity• Fully enclosed front pulleys• Retractable fork extensions that

house inside forks• Cable feeds up and away from

operators face for added safety

SUM2118 - 18 foot

$2129 each

part #SUM2020• 800 lb lifting capacity up

to 20 feet high !!• One piece construction -

no loose parts or telescopingmasts

• Rolls through standarddoorways

• Reversible forks• 5" Lockable casters and

10" rough terrain wheels

$2557 each

VERMETTE MATERIAL LIFTS

part # VER6515Light weight, fold-up designlets one person lift heavyloads up to 650 lbs. to 15 feet

$143900

Just219 lbs.

The perfect Lift for:• HVAC Contractors• Electrical Contractors• Industrial Maintenance• Steel Erectors

The Recognized Leader inMaterial Handling Equipment

SUM2124 - 24 foot

$2445 each

each

• Transportation and storageare made easy with new‘Fold-Up’ design

• One person can easily loadlift in a truck or van

OSHAaccepted

VER512A (12'-500#)$123900 each

VER520A-5 (20'-500#)

with 5" CASTERS$143500 each

Hi Jack*part #VERA-1(15'-500#)

* castersnot included

$74900each

NYLON SLINGS WIRE ROPE SLINGS2 Ply Heavy Duty Eye and Eye

Many other sizes available!


WRS38-6EE 3/8" x 6' $18.46WRS38-8EE 3/8" x 8' $21.33WRS38-12EE 3/8" x 12' $26.68WRS12-6EE 1/2" x 6' $22.31WRS12-8EE 1/2" x 8' $25.47WRS12-12EE 1/2" x 12' $31.77

Flexibility, weight, strength, andnon-marring properties make nylonslings the most sought after slingsfor contractors and riggers alike!

"Tough-Lock™" slings are uniquelyconstructed unlike various return wireloop types. "Flemish" splice, resultsin 100% breaking strength promotingadditional safety! Also available 'HandSpliced' furnished without sleeves.


NYS2-8EEHD2 2" x 8' $24.98NYS2-10EEHD2 2" x 10' $29.53NYS2-12EEHD2 2" x 12' $34.10NYS2-16EEHD2 2" x 16' $43.18NYS2-20EEHD2 2" x 20' $52.30NYS2-24EEHD2 2" x 24' $61.41

Many more sizes available!

part # size feet/pail < full pail full pail

CMB014-0323 3/16” 250 1.43 .95CMB014-0423 1/4” 141 2.29 1.53CMB014-0523 5/16” 92 3.23 2.15CMB014-0623 3/8” 63 4.69 3.13

CMB018-1613 3/8" 75 5.74 3.83

* Uses: Designed for use in load binding, towing, loggingand other applications requiring high strength

DO NOT USE FOR OVERHEAD LIFTING

HIGH TEST CHAIN *

price per foot

21

Optional Pipe Cradlepart #SUM783705

Optional Fork Extensionspart #SUM783691

$8982 set

$7862 set

1-5/8" x 1-5/8" x 12 gauge10 ft. or 20 ft. lengths$1.59 per foot

1-5/8" x 1-5/8" x 14 gauge10 ft. or 20 ft. lengths$1.41 per foot

STRUT ACCESSORIESand

20 foot lengths, 18 gauge, 2" high x 1-1/2" wide, punched2" on center. (The bending resistance corresponds to a2" x 2" x 3/16" angle or SMACNA "I" strength.)Galvanized, easy to cut, light in weight, low in theft.

Sold in full bundles of 500 feet only.125 Washers included with each bundle.

Also available in Hot Dip Galvanized, Stainless, Brass, B7 Structural and other exotic materials

Plain Steelpart # size ft/bundle price/cft part # size ft./bundle price/cft

ROD1420-12P 1/4-20 x 12' 600 $20.52 ROD1420-12Z 1/4-20 x 12' 600 $23.36ROD3816-12P 3/8-16 x 12' 300 $38.96 ROD3816-12Z 3/8-16 x 12' 300 $41.36ROD1213-12P 1/2-13 x 12' 144 $66.56 ROD1213-12Z 1/2-13 x 12' 144 $73.00ROD5811-12P 5/8-11 x 12' 96 $107.86 ROD5811-12Z 5/8-11 x 12' 96 $127.56ROD3410-12P 3/4-10 x 12' 60 $156.48 ROD3410-12Z 3/4-10 x 12' 60 $185.44ROD789-12P 7/8-9 x 12' 48 $267.98 ROD789-12Z 7/8-9 x 12' 48 $317.64ROD18-12P 1-8 x 12' 24 $351.20 ROD18-12Z 1-8 x 12' 24 $416.46

FULLYTHREADED ROD

Zinc Plated

Prices are based on full bundle purchasesBroken bundles at a slightly higher price.

part # description price

DUCDMW EXTRA WASHERS (125/box) $18.00/box

DUCTBCLAMP TRAPEZE BEAM CLAMP ASSEMBLY $3.21/ea

part #DUCDMTH price per foot

500' 1,000' 1,500'

$1.36 $1.21 $1.18

TRAPEZE DUCT HANGER

DUCTBCLAMP

Beam clamp fastenshanger profile tostructural membersup to 1-1/2" thick

GalvanizedBand Iron

part # description 100 ft. 1000 ft. 3000 ft.

GBI16 16 ga. x 1" Wide $37.77 $37.29 $36.37

GBI18 18 ga. x 1" Wide $25.77 $25.45 $24.82

GBI26 26 ga. x 1" Wide $13.36 $13.19 $12.87

price per cft.

Sold in 10 ft lengths, 100 ft. per bundle

For round pipe up to 50" diameter• Uses 1" x 18 - 22 ga. band iron• Works with 5/16" or 3/8" threaded rod• 660 lb. load rating

part #DUC4703

1-199$1.21 ea

200 or more$1.01 ea

DUCT STRAPBRACKET

Dura-Green™ Epoxy Coatingwith 9/16" x 7/8" slots

Prices based on a minimum purchase of 100 feet.Smaller quantities at slightly higher prices.

We StockGalvanizedStrut Too!!

22


ARM89-001 1/4”-20 x 1” $4.61ARM89-002 5/16”-18 x 1-1/8” $5.04ARM89-003 3/8”-16 x 1-1/4” $5.24ARM89-005 1/2”-13 x 1-1/2” $6.41ARM89-007 5/8”-11 x 1-1/8” $10.16ARM89-008 3/4”-10 x 1-1/4” $13.01ARM89-010 1”-8 x 1-1/2” $23.04


ARM89-021 1/4”-20 x 1” $4.54ARM89-022 5/16”-18 x 1-1/8” $5.00ARM89-023 3/8"-16 x 1-1/4” $5.00ARM89-025 1/2"-13 x 1-1/2” $6.32ARM89-027 5/8"-11 x 1-1/8” $10.31ARM89-028 3/4”-10 x 1-1/4” $12.55

EYE & EYE TURNBUCKLESHot Dip Galvanized

Also available with hook, jaw or stub ends. Or bodies only.

SOLID BRASS Sheet Metal Screws10 x 3/4 ‘Combo’ Head (slotted / phillips)

100 per box

$52.751,000 per carton

$31.65

Part # Size Box Qty. Price/c

RCN14-38Z 1/4-20 x 3/8-16 100 $62.60RCN38-12Z 3/8-16 x 1/2-13 100 $109.63

REDUCINGROD COUPLING NUTS

FORGED LIFTING EYES

Plain Pattern

ROD COUPLING NUTS

Bulk PricingAvailable

Zinc Plated

Part # Size qty/box price/c

RCN1420Z 1/4-20 50 $48.78RCN51618Z 5/16-18 25 $75.61

RCN3816Z 3/8-16 25 $90.22RCN1213Z 1/2-13 25 $97.52RCN5811Z 5/8-11 20 $177.99RCN3410Z 3/4-10 20 $221.87RCN789Z 7/8-9 10 $392.52RCN18Z 1-8 10 $514.39

RCN1147Z 1-1/4-7 10 $941.02


TBK14-4 1/4 x 4” $14.59TBK516-412 5/16 x 4-1/2” $18.19TBK38-6 3/8 x 6” $20.18TBK12-6 1/2 x 6” $22.95TBK12-9 1/2 x 9” $30.11TBK12-12 1/2 x 12” $35.55TBK58-6 5/8 x 6” $29.55

Shoulder Pattern

2" X 2" SQUARE PLATE WASHERSSquare plate washers provide a largerbearing surface for wide load distribution.

1/4" thick

PlainSteel

Zinc

$12798

UNIVERSAL BEAM CLAMPS1/4-20 x 1/2 grip Zinc Plated

part # MRL600

BRIDLE RINGS

per hundred

CABLESUPPORT

prices shown are per hundred pieces

Use in: WallboardUse with: #2 or #3 Phillips screwdriver and #8

sheet metal screw or drywall screwMade of: Du Pont ZYTEL® nylon or Zinc

Size: 3/8" to 1" wallboard

ZIP-it ® ANCHORS

part #RAW2345

$23.52/c

Using a Phillips screwdriver the ZIP-it drills its own holeand drives into the wall in one motion. Insert a sheetmetal screw with the same screwdriver for a tight,secure, but removable fit.

$25.20/cpart #RAW2346

Nylon Zinc

MUSHROOM HEAD

Grade 8.2 Steel.

Ideal for hanging

SPIKE ® ANCHORS

part # size price/cRAW5503 3/16" x 1-1/4" $23.40RAW5504 3/16" x 1-1/2" $25.38RAW5506 3/16" x 2" $31.02RAW5510 3/16" x 3" $41.70RAW5511 3/16" x 3-1/2" $44.40RAW5512 3/16" x 4" $47.82

RAW5522 1/4" x 1" $26.82RAW5523 1/4" x 1-1/4" $29.94RAW5524 1/4" x 1-1/2" $30.48RAW5526 1/4" x 2" $36.12RAW5528 1/4" x 2-1/2" $38.64RAW5530 1/4" x 3" $43.68RAW5531 1/4" x 3-1/2" $47.10RAW5532 1/4" x 4" $48.66

ALSO AVAILABLE IN3/8" & 1/2" DIAMETERS.

STAINLESS TOO!!

part # BRI112-TH$8132

per hundred

1/4-20 thread x 1-1/2" diameter ring

part #CPA10-34P-BR23

part number bolt size price/c

SQW14-2X2-14P 1/4" $178.00

SQW38-2X2-14P 3/8" $178.00

SQW12-2X2-14P 1/2" $178.00

SQW38-2X2-14Z 3/8" $211.00

Albany Steel and Brass.A Proud Member of

SMACNA Chicago since 1995

part # for flange size price/c

HIT121 1/16" to 1/4" $51.08HIT122 1/8" to 1/4" $48.56HIT123 5/16" to 1/2" $51.98HIT124 9/16" to 3/4" $77.22

Grips tight, resists twists and vibration.Easily driven on flange with hammer rap.

FLANGE BEAM CLIPS

100 PER BOX / FULL BOXES ONLY

PARALLEL STYLE

RIGHT ANGLE STYLE

BEAM CLIP/STRAP HANGERCOMBINATION


HIT122-532 1/8" to 1/4" $107.64HIT123-532 5/16" to 1/2" $107.64


HIT122-531 1/8" to 1/4" $97.88HIT123-531 5/16" to 1/2" $97.88

PRESSED STEELBEAM CLAMPS

zinc plated malleable iron

ELECTRICAL STYLEBEAM CLAMPS

part # size box. qty Price/cABC951 1/4" 50 $86.66ABC953 3/8" 25 $447.90ABC955 1/2" 20 $841.33

3/4" GRIP BEAM 'C' CLAMPpart # size box. qty Price/c

ABC926 1/4" 100 $138.00ABC353 3/8" 100 $136.40ABC354 1/2" 100 $204.60

WIDE 1-1/4" GRIP BEAM 'C' CLAMPpart # size box. qty Price/c

ABC363 3/8" 100 $232.00ABC364 1/2" 100 $316.00

Sale prices are based on full box purchases.Broken boxes at slightly higher prices.

FITTERS BEAM CLAMPS

part # size Price/cABC253 3/8" $234.00ABC254 1/2" $360.00 Locknut

Included

Locknut

Included

SAMMYS® RODANCHORING SYSTEM

rod shank shankpart # application size diameter length price/c

SDPGST200 Wood 1/4-20 1/4" 2" $84.62SDPGST10 Wood 3/8-16 1/4" 1" $84.62SDPGST20 Wood 3/8-16 1/4" 2" $84.62SDPGST30 Wood 3/8-16 1/4" 3" $89.08SDPGST40 Wood 3/8-16 1/4" 4" $106.90

SDPCST200 Concrete 1/4-20 5/16" 1-1/2" $99.90SDPCST20 Concrete 3/8-16 5/16" 1-1/2" $99.90

SDPDST10 Steel 3/8-16 1/4-14 1" $88.71SDPDST20 Steel 3/8-16 1/4-14 2" $95.71SDPDSTR1 Steel 3/8-16 1/4-20 1" $93.36SDPDSTR516 Steel 3/8-16 5/16-18 1-1/4" $100.40SDPTEK50 Steel 3/8-16 12-24 1-1/2" $112.06

Vertical Mount

Horizontal Mount (Sidewinders)

rod shank shankpart # application size diameter length price

SDPSWG20 Wood 3/8-16 1/4" 2" $109.14

SDPSWC20 Concrete 3/8-16 5/16" 1-1/2" $129.41

SDPSWDR1 Steel 3/8-16 1/4-20 1" $119.06SDPSWDR516 Steel 3/8-16 5/16-18 1-1/4" $123.72

part # size price/c

TGR1024 10-24 $49.31TGR1420 1/4-20 $49.31TGR3816 3/8-16 $93.08

• Strong - up to 2x the load of anold-fashioned wing toggle

• Solid metal channel resists vibration &shock• Save time - at least 6 minutes per anchor

compared to standard wing toggles• Can use a screw gun; anchor does not spin• Use a shorter bolt (no need to carry a wing

through the wall)• New strap design snaps off flush & does

not break prematurely• Smallest installation hole for each bolt size• New golden plating is 7x more corrosion-

resistant• Reusable in same hole—remove bolt without

losing the anchor* Screws sold separately 24

1

2

3

4

SNAPTOGGLE®

Heavy-Duty Toggle Bolts

SLOTTED HEX WASHER PHILLIPS FLAT

GENUINE TAPCON ® MASONRY ANCHORS

Also Available InSTAINLESS STEEL

part # size price/cTCN316-114H 3/16" x 1-1/4" $12.96TCN316-134H 3/16" x 1-3/4" $14.37TCN316-214H 3/16" x 2-1/4" $15.71TCN316-234H 3/16" x 2-3/4" $17.02TCN316-314H 3/16" x 3-1/4" $20.40TCN316-334H 3/16" x 3-3/4" $26.30TCN316-4H 3/16" x 4" $32.23

TCN14-114H 1/4" x 1-1/4" $16.21TCN14-134H 1/4" x 1-3/4" $18.29TCN14-214H 1/4" x 2-1/4" $20.50TCN14-234H 1/4" x 2-3/4" $23.45TCN14-314H 1/4" x 3-1/4" $26.80TCN14-334H 1/4" x 3-3/4" $33.30TCN14-4H 1/4" x 4" $37.45TCN14-5H 1/4" x 5" $57.62TCN14-6H 1/4" x 6" $72.36

'MINI'DROP-IN ANCHORS

part # size price/cTCN316-114F 3/16" x 1-1/4" $12.96TCN316-134F 3/16" x 1-3/4" $14.37TCN316-214F 3/16" x 2-1/4" $15.71TCN316-234F 3/16" x 2-3/4" $17.02TCN316-314F 3/16" x 3-1/4" $20.40TCN316-334F 3/16" x 3-3/4" $26.30TCN316-4F 3/16" x 4" $32.23

TCN14-114F 1/4" x 1-1/4" $16.21TCN14-134F 1/4" x 1-3/4" $18.29TCN14-214F 1/4" x 2-1/4" $20.50TCN14-234F 1/4" x 2-3/4" $23.45TCN14-314F 1/4" x 3-1/4" $26.80TCN14-334F 1/4" x 3-3/4" $33.30TCN14-4F 1/4" x 4" $37.45TCN14-5F 1/4" x 5" $57.62

TCN14-6F 1/4" x 6" $72.36

STOP DRILLFor 'MINI' Drop-In Anchors

Ideal for...• Hollow Core Concrete• Pre-Cast Plank• Post Tension Slabs

REDDCX-138 1/2" DIA. x 13/16 Drill Depth $26.88For use with 3/8" RX Drop-in

REDDCX-112 5/8" DIA. x 1-3/16 Drill Depth $29.60For use with 1/2" RX Drop-in

size part # price/c

3/8" DIA38-RX $25.80

1/2" DIA12-RX $43.14

For use in hollow-core,pre-cast plank andpost-tension slabs

25

REDI-DRIVEANCHORS

Hammer-Drive Masonry Anchors -Specifically for Anchoring into Concrete, Block and Brick

The Redi-Drive is a high performance small diameter one-piecehammer-drive anchor. The anchor holds based on a frictionprinciple - the shank diameter is larger than the drill hole size.

Redi-Drive Anchors are suitable for overhead applications

part # Length Head Style Price/c

REDRD4-034 3/4" Button $14.08REDRD4-118 1-1/8" Button $15.34REDRD4-158 1-5/8" Button $16.88REDRD4-200 2" Button $21.38REDRD4-212 2-1/2" Button $26.32REDRD4-300 3" Button $29.77

REDPD4-112 1-1/2" 1/4-20 $41.90REDPD4-134 1-3/4" 3/8-16 $50.64

REDTD4-112 1-1/2" Tie Wire $53.73

1/4" DIA14-RM $25.74 5/8" DIA58-RM $135.43

3/8" DIA38-RM $30.48 3/4" DIA34-RM $230.22

1/2" DIA12-RM $56.87

size part # price/c part# price/c

1/4" DIA14 $20.58 DIA14-18-8 $150.08

3/8" DIA38 $24.38 DIA38-18-8 $253.68

1/2" DIA12 $45.51 DIA12-18-8 $458.27

5/8" DIA58 $108.35 DIA58-18-8 $970.17

3/4" DIA34 $184.17 DIA34-18-8 $1,505.24

Prices based on a full box purchase.Some items available in smaller quantites at slightly higher prices

STEEL 18-8 STAINLESS

DROP-IN ANCHORS

Also available in316 stainless

STEEL DROP-IN WITH LIP

PLASTIC ANCHOR KITS$7.99 each

part #CPA10-12K

CONSISTS OF...100 10-12 x 1" Conical Anchors100 10 x 1" Combo Pan Sheet Metal Screw

1 1/4" Carbide Masonry Drill

HAMMER-SET ™ NAIL-DRIVE ANCHORS

100 Per Box / Full Boxes Only

The HAMMER-SET® one-piece zinc-plated steel anchorconsists of an expansion body and expander drive pin.Not for use in overhead applications.

part# size price/cZAM316-78 3/16" x 7/8" $13.77ZAM14-34 1/4" x 3/4" $14.29ZAM14-1 1/4" x 1" $14.72ZAM14-114 1/4" x 1-1/4" $16.85ZAM14-112 1/4" x 1-1/2" $19.98ZAM14-2 1/4 x 2" $24.08 Also Available with

STAINLESSDrive Pin

Trubolt®

WEDGE ANCHORS

Also available from STOCK inHot Dip Galvanized, 18.8 and 316 Stainless !!

part # size box qty. price/cWDG14-134 1/4 x 1-3/4" 100 $30.34WDG14-214 1/4 x 2-1/4" 100 $31.60WDG14-314 1/4 x 3-1/4" 100 $33.92

WDG38-214 3/8 x 2-1/4" 50 $47.76WDG38-234 3/8 x 2-3/4" 50 $51.10WDG38-3 3/8 x 3" 50 $52.16WDG38-334 3/8 x 3-3/4" 50 $55.76WDG38-5 3/8 x 5" 50 $67.80WDG38-7 3/8 x 7" 50 $152.20

WDG12-234 1/2 x 2-3/4" 25 $88.26WDG12-334 1/2 x 3-3/4" 25 $92.26WDG12-414 1/2 x 4-1/4" 25 $95.14WDG12-412 1/2 x 4-1/2" 25 $96.90WDG12-512 1/2 x 5-1/2" 25 $108.36WDG12-7 1/2 x 7" 25 $130.74

WDG58-312 5/8 x 3-1/2" 10 $164.38WDG58-414 5/8 x 4-1/4" 10 $175.18WDG58-5 5/8 x 5" 10 $183.56WDG58-6 5/8 x 6" 10 $193.52WDG58-7 5/8 x 7" 10 $230.68WDG58-812 5/8 x 8-1/2" 10 $299.80WDG58-10 5/8 x 10" 10 $461.28

WDG34-414 3/4 x 4-1/4" 10 $226.78WDG34-434 3/4 x 4-3/4" 10 $232.74WDG34-512 3/4 x 5-1/2" 10 $246.04WDG34-614 3/4 x 6-1/4" 10 $280.24WDG34-7 3/4 x 7" 10 $333.28WDG34-812 3/4 x 8-1/2" 10 $449.34WDG34-10 3/4 x 10" 10 $503.68WDG34-12 3/4 x 12" 10 $782.26

WDG78-6 7/8 x 6" 5 $618.12WDG78-8 7/8 x 8" 5 $734.24WDG78-10 7/8 x 10" 5 $818.50

WDG1-6 1 x 6" 5 $639.58WDG1-9 1 x 9" 5 $845.70WDG1-12 1 x 12" 5 $1044.92

WDG114-9 1-1/4 x 9" 5 $1906.04WDG114-12 1-1/4 x 12" 5 $2047.00

SOLD IN FULL BOXES ONLY

Trubolt® +WEDGE ANCHORS

FOR SEISMIC APPLICATIONS

part # size box qty. price/cWDG38-3-PLUS 3/8 x 3" 50 $116.43WDG38-334-PLUS 3/8 x 3-3/4" 50 $147.78WDG38-5-PLUS 3/8 x 5" 50 $161.84

WDG12-334-PLUS 1/2 x 3-3/4" 25 $207.80WDG12-412-PLUS 1/2 x 4-1/2" 25 $214.88WDG12-512-PLUS 1/2 x 5-1/2" 25 $233.22WDG12-7-PLUS 1/2 x 7" 25 $261.88

WDG58-5-PLUS 5/8 x 5" 10 $331.72WDG58-6-PLUS 5/8 x 6" 10 $380.56WDG58-7-PLUS 5/8 x 7" 10 $406.04WDG58-812-PLUS 5/8 x 8-1/2" 10 $450.04

part # size box qty. price/cLDT3816 3/8 x 1-3/4" 50 $59.82LDT3824 3/8 x 2-1/2" 50 $83.26LDT3830 3/8 x 3" 50 $91.62LDT3840 3/8 x 4" 50 $98.32LDT3850 3/8 x 5" 40 $115.80

LDT1230 1/2 x 3" 25 $146.56LDT1240 1/2 x 4" 25 $159.90LDT1250 1/2 x 5" 25 $173.22LDT1260 1/2 x 6" 20 $246.88

LDT5830 5/8 x 3" 10 $238.52LDT5840 5/8 x 4" 10 $267.24LDT5850 5/8 x 5" 10 $301.76LDT5860 5/8 x 6" 10 $333.36

LDT3444 3/4 x 4-1/2" 10 $321.84LDT3454 3/4 x 5-1/2" 10 $362.08LDT3462 3/4 x 6-1/4" 10 $419.58

part # size box qty. price/cLDT3830X 3/8 x 3" 50 $95.80LDT3840X 3/8 x 4" 50 $102.78LDT3850X 3/8 x 5" 40 $121.04

LDT1230X 1/2 x 3" 25 $187.54LDT1240X 1/2 x 4" 25 $205.18LDT1250X 1/2 x 5" 25 $232.00

The Easy, Fast, High Performing, Removable Tapcon StyleAnchor, Available up to 3/4" Diameter

'LDT' ANCHORS(Large Diameter Tapcon)

LDT Anchors are also available in 410 Stainless

• Finished Head

• Fully Removable

• Uses Standard ANSI Drill Bits

Also available with Coating

1,000 hours salt spray ASTM B117.Approved for use in ACQ and MCQ lumber.

Fast Dispensing, Fast Curing Anchoring Adhesive

A7 Acrylic 7

• All weather formula• Rods insert easily in both

horizontal and vertical applications• No cartridge heating required in

cold temperatures• Consistent mix ratio• Single formula for hollow or solid base materials• No drip or sag formula cleans up easily• Works in damp and underwater applications

Usabledown toZERO

Degrees F

26

Part # Diameter Grip Range Box Qty Carton Qty Full Box Full Carton*

CHEAA32F 3/32" .020-.125 1000 10M $5.20 $2.76CHEAA34F 3/32" .126-.250 1000 10M $5.35 $2.84

CHEAA41F 1/8" up to .062 1000 10M $4.85 $2.57CHEAA42F 1/8" .063-.125 1000 10M $3.75 $1.99CHEAA43F 1/8" .126-.187 1000 10M $4.10 $2.17CHEAA44F 1/8" .188-.250 1000 10M $4.25 $2.25CHEAA45F 1/8" .251-.312 1000 10M $5.70 $3.02CHEAA46F 1/8" .313-.375 1000 10M $5.80 $3.07CHEAA48F 1/8" .438-.500 1000 10M $6.85 $3.63

CHEAA52F 5/32" .020-.125 1000 10M $6.70 $3.55CHEAA54F 5/32" .126-.250 1000 10M $7.10 $3.76CHEAA56F 5/32" .251-.375 1000 10M $5.61 $2.97

CHEAA62F 3/16" .020-.125 500 10M $8.25 $4.37CHEAA64F 3/16" .126-.250 500 10M $8.50 $4.51CHEAA66F 3/16" .251-.375 500 10M $9.70 $5.14CHEAA68F 3/16" .376-.500 500 10M $10.65 $5.64CHEAA610F 3/16" .501-.625 500 10M $12.80 $6.78

CHEAS32F 3/32" .020-.125 1000 10M $4.75 $2.52CHEAS34F 3/32" .126-.250 1000 10M $5.10 $2.70

CHEAS42F 1/8" .063-.125 1000 10M $3.55 $1.88CHEAS43F 1/8" .126-.187 1000 10M $3.80 $2.01CHEAS44F 1/8" .188-.250 1000 10M $3.95 $2.09CHEAS45F 1/8" .251-.312 1000 10M $5.95 $3.15CHEAS46F 1/8" .313-.375 1000 10M $6.15 $3.26

CHEAS52F 5/32" .020-.125 1000 8M $5.50 $2.92CHEAS54F 5/32" .126-.250 1000 8M $6.30 $3.34CHEAS56F 5/32" .251-.375 1000 8M $7.20 $3.82

CHEAS62F 3/16" .020-.125 500 5M $6.75 $3.58CHEAS64F 3/16" .126-.250 500 4M $7.55 $4.00CHEAS66F 3/16" .251-.375 500 4M $8.75 $4.64CHEAS68F 3/16" .376-.500 500 4M $9.70 $5.14CHEAS610F 3/16" .501-.625 500 4M $11.40 $6.04CHEAS612F 3/16" .626-.750 500 4M $15.95 $8.45

CHESS32F 3/32" .020-.125 1000 10M $5.90 $3.13CHESS34F 3/32" .126-.250 1000 10M $6.10 $3.23

CHESS41F 1/8" up to .062 1000 10M $4.05 $2.15CHESS42F 1/8" .063-.125 1000 10M $3.55 $1.88CHESS43F 1/8" .126-.187 1000 10M $3.90 $2.07CHESS44F 1/8" .188-.250 1000 10M $3.95 $2.09CHESS45F 1/8" .251-.312 1000 10M $5.90 $3.13CHESS46F 1/8" .313-.375 1000 10M $5.95 $3.15CHESS48F 1/8" .438-.500 1000 10M $7.15 $3.79

CHESS52F 5/32" .020-.125 1000 8M $5.85 $3.10CHESS54F 5/32" .126-.250 1000 8M $6.10 $3.23CHESS56F 5/32" .251-.375 1000 5M $7.80 $4.13CHESS58F 5/32" .376-.500 1000 5M $8.10 $4.29

CHESS62F 3/16" .020-.125 500 4M $7.30 $3.87CHESS64F 3/16" .126-.250 500 4M $7.40 $3.92CHESS66F 3/16" .251-.375 500 4M $8.90 $4.72CHESS68F 3/16" .376-.500 500 4M $10.35 $5.49CHESS610F 3/16" .501-.625 500 4M $13.15 $6.97CHESS612F 3/16" .626-.750 500 3M $14.22 $4.77

CHESS84F 1/4" .126-.250 100 2M $18.05 $9.57CHESS86F 1/4" .251-.375 100 2M $19.40 $10.28CHESS88F 1/4" .376-.500 100 1M $21.85 $11.58CHESS810F 1/4" .501-.625 100 1M $24.85 $13.17CHESS812F 1/4" .626-.750 100 1M $27.80 $14.73

BLIND RIVETS

Price Per Hundred

We STOCK

Stainless & Copper

Rivets too!

Aluminum RivetSteel Mandrel

Aluminum RivetAluminum Mandrel

27 *Please call for special pricing on larger, multiple-carton orders.

Steel RivetSteel Mandrel

Also available in Large Flangeand Countersunk head styles

RIVET TOOLSItem part # description price each1 RGN202B Heavy-Duty / Hand Held $40.502 RGN2-WAY Two Way / Hand Held $39.003 RGNSNII "Lazy Tong" 1/4" Capacity $185.504 RGNGH-4024 Two Handed Tool 1/4" Capacity $124.455 RGNSUPER 800 Air Hydraulic Riveter $538.65

23

4

5

1

FASTENERS

Hex Cap Screws and FullThread Tap Bolts

Hex NutsFinished Heavy Jam Carriage Bolts

Hex Lag ScrewsFlat Washers

Wrought SAE Structural Fender Washers

Slotted and PhillipsTapping and Thread Cutting Screws

Slotted and PhillipsMachine Screws Hanger Bolts

Drywall Screws, Deck ScrewsParticle Board Screws

LockwashersSplit Internal External

Miscellaneous NutsCap Lock Wing

The fasteners shown above represent just a portion of our product offering.Please contact our office regarding requirements for fasteners not shown on this page.

28

SLOTTEDHEX WASHER HEAD

SPEED SCREWS

part # size 100 1000 2500 5000

TEK818-12-HW2-410 8-18 x 1/2" $7.65 $6.50 $5.74 $5.13

TEK818-34-HW2-410 8-18 x 3/4" $8.50 $7.23 $6.38 $5.70

TEK1016-12-HW3-410 10-16 x 1/2" $10.10 $8.59 $7.58 $6.77

TEK1016-34-HW3-410 10-16 x 3/4" $11.10 $9.44 $8.33 $7.44

TEK1016-1-HW3-410 10-16 x 1" $12.45 $10.58 $9.34 $8.34

TEK1214-34-HW3-410 12-14 x 3/4" $15.40 $13.09 $11.55 $10.32

TEK1214-1-HW3-410 12-14 x 1" $16.50 $14.03 $12.38 $11.06

TEK1414-34-HW3-410 1/4-14 x 3/4" $20.95 $17.81 $15.71 $14.04

TEK1414-1-HW3-410 1/4-14 x 1" $25.20 $21.42 $18.90 $16.88

TEK1414-112-HW3-410 1/4-14 x 1-1/2" $30.25 $25.71 $22.69 $20.27

TEK818-12-HW2-188 8-18 x 1/2" $22.05 $17.64 $15.44 $13.23

TEK818-34-HW2-188 8-18 x 3/4" $24.15 $19.32 $16.91 $14.49

Hex Washer Head

STAINLESS STEELDRILL SCREWS

prices per hundred410 STAINLESS STEEL

18-8 STAINLESS STEEL

TEK818-12-HW2-MM 8-18 x 1/2" 2 $32.54 $20.34 $16.27

TEK818-34-HW2-MM 8-18 x 3/4" 2 $39.16 $24.48 $19.58

TEK1016-34-HW3-MM 10-16 x 3/4" 3 $53.86 $33.67 $26.93

TEK1016-1-HW3-MM 10-16 x 1" 3 $57.62 $36.01 $28.81

TEK1214-34-HW3-MM 12-14 x 3/4" 3 $66.49 $41.56 $33.24

TEK1214-1-HW3-MM 12-14 x 1" 3 $82.72 $51.70 $41.36

TEK1224-114-HW4-MM 12-24 x 1-1/4" 4 $99.11 $61.95 $49.56

TEK1224-112-HW5-MM 12-24 x 1-1/2" 5 $118.34 $73.96 $59.17

TEK1414-1-HW3-MM 1/4-14 x 1" 3 $132.17 $82.61 $66.08

TEK818-12-PP2-MM 8-18 x 1/2" 2 $30.42 $19.02 $15.21

PHILLIPS PAN HEAD

Fusing the maximum corrosionresistance of an 18-8 stainless screw with

the power of a hardened steel drill point

HEX WASHER HEADQuantity

prices per hundred

prices per hundred

part # size 100 1M 5M 10M 25M

SPD6-38Z-GSP 6 x 3/8" $1.73 $1.30 $1.15 $.1.01 $.86

SPD7-12Z-GSP 7 x 1/2" $2.03 $1.52 $1.35 $1.18 $1.01

SPD8-12Z-GSP 8 x 1/2" $2.09 $1.57 $1.39 $1.22 $1.04

SPD8-34Z-GSP 8 x 3/4" $2.54 $1.91 $1.70 $1.48 $1.27

SPD8-1Z-GSP 8 x 1" $2.81 $2.11 $1.87 $1.64 $1.40

SPD8-112Z-GSP 8 x 1-1/2" $3.89 $2.92 $2.59 $2.27 $1.94

SPD8-2Z-GSP 8 x 2" $4.97 $3.73 $3.31 $2.90 $2.48

SPD10-12Z-GSP 10 x 1/2" $2.33 $1.75 $1.55 $1.36 $1.16

SPD10-34Z-GSP 10 x 3/4" $3.17 $2.38 $2.11 $1.85 $1.58

SPD10-1Z-GSP 10 x 1" $3.41 $2.56 $2.27 $1.99 $1.70

SPD10-12Z-ESP 10 x 1/2" $2.49 $1.49 $1.37 $1.25 $1.12

SPD10-34Z-ESP 10 x 3/4" $2.89 $1.88 $1.73 $1.57 $1.41

SPD10-1Z-ESP 10 x 1" $3.49 $2.18 $2.00 $1.82 $1.64

SPD10-112Z-ESP 10 x 1-1/2" $4.64 $2.78 $2.55 $2.32 $2.09

Combinable in 5000 pc. lots

MULTI-METALDRILL SCREWS

part # size pt.size 100 500 1000

1/4" HEX HEAD STANDARD Self Piercing Screws

18-8 (304) StainlessHead and Shank

Hardened SteelDrill Point

Fused

5/16" HEX HEAD "SUPER" Self Piercing Screws

29

We stock 410 Stainless

Speed Screws too!!


APXMDA08 1/4" x 1-5/8" $3.35APXMDA10 5/16" x 1-5/8" $3.35

NST14-2916-MAG 1/4" x 2-9/16" $4.43NST516-2916-MAG 5/16" x 2-9/16" $4.48NST38-2916-MAG 3/8" x 2-9/16" $5.87NST716-2916-MAG 7/16" x 2-9/16" $7.76

1/4" HEX SHANK

#5 point for extra heavy gauge metal- 3/16" thru 1/2"

part # size ctn.qty. < full ctn. full ctnTEK1224-78-HW4 12-24 x 7/8" 5000 $10.09 $7.97TEK1224-114-HW4 12-24 x 1-1/4" 3500 $11.24 $8.87TEK1414-5-HW4 1/4-14 x 5" 500 $72.81 $54.61

#4 point for heavy gauge metal - 3/16" thru 3/8"

part # size ctn.qty. < full ctn. full ctnTEK1224-114-HW5K 12-24 x 1-1/4" 3500 $20.73 $16.37TEK1224-112-HW5 12-24 x 1-1/2" 2500 $22.45 $17.73TEK1224-2-HW5 12-24 x 2" 2000 $26.30 $20.76TEK1414-6-HW5 1/4-14 x 6" 250 $124.65 $93.49

prices per hundred

"Heavy Gauge"DRILL SCREWS

HEX WASHER HEAD

MAGNETIC NUTSETTERS

the PENETRATOR +®

Premium quality, high performance drill screws. Engineered byALBANY STEEL AND BRASS especially for the HVAC Industry.The special 'WALK RESISTANT' point assures the fastest drillingtimes. CUPPED SERRATED WASHER FACE provides a level ofvibration resistance unachievable with standard flat serrations.EXTRA HIGH HEAD virtually eliminates fastener drop-out of the driver.

Others Have Copied it, We Invented it !!

10 x 3/4" Hex WasherPenetrator +®

5,500 per carton

$2.09 perhundred

Includes a FREE 5/16" Magnetic Nutsetter

prices per hundred

The only sourcein the world forthe entire familyof Penetrator +®

Drill Screws

30

box carton 100 1000 1 cartonpart # size qty. qty. pcs pcs or more

TEK818-12-HW2+ 8 x 1/2" 100 10M $5.95 $3.57 $2.38TEK818-34-HW2+ 8 x 3/4" 100 7500 $6.55 $3.93 $2.62TEK818-1-HW2+ 8 x 1" 100 5000 $8.43 $5.06 $3.37TEK1016-1-HW3+ 10 x 1" 100 3500 $12.21 $7.33 $4.88TEK1214-34-HW3+ 12 x 3/4" 100 5000 $13.91 $8.35 $5.56TEK1214-1-HW3+ 12 x 1" 100 3000 $15.85 $9.51 $6.34TEK1414-34-HW3+ 1/4 x 3/4" 100 3500 $17.35 $10.41 $6.94TEK1414-1-HW3+ 1/4 x 1" 100 2500 $19.92 $11.95 $7.97TEK1414-114-HW3+ 1/4 x 1-1/4" 100 2000 $21.59 $12.95 $8.64

Our Patentthat

Proves it.

" it's not just for spiral anymore "

High Speed Cable Hanger Solutionsfor the HVAC & Mechanical Industry

Trapeze No.2Purpose-made single channel, ideal for multi-tieredinstallations

• Ideal for fast suspension of rectangular duct,cable tray etc.

• Tapered design - accommodates all slots sizes• Discreet - fits completely inside the channel• Pin allows rapid adjustment• Aesthetic design• Load rated at 100 lbs. with a 5:1 safety factor• Supplied as a ready-to-use kit

NEW

No.2 Duct TrapezeGripple Duct Trapeze No.2 for hangingrectangular ducting

• Spreads the load across 3 fixing points, forself-drilling screws or pop rivets (not included)

• Pin allows rapid adjustment• Rubber pad prevents leakage• Load rated at 100 lbs. with a 5:1 safety factor• Supplied as a ready-to-use kit

Trapeze No.3Single channel Gripple, ideal for multi-tiered installations

• Quick and effective solution for pre-fabricated units• Slots easily into strut• Ideal for fast suspension of rectangular duct, cable

basket and cable tray• Pin allows easy adjustment and is removable• Load rated at 200 lbs. with a 3:1 safety factor• Supplied in a ready-to-use kit with a choice of end-fixings

NEWGripple hangers areavailable in five load ratedsizes up to 715 lbs. andincorporate a 5:1 safetyfactor in a vertical plane.Standard lengths range from5 ft to 30 ft. Other lengthscan be made to order.

• Gripple hangers are the versatile wayto suspend static loads.

• Reduces installation by up to 6 timescompared to threaded rod, band ironchain or other loose cable systems.

• Pre-cut cable with a pre-fabricatedend fixing for maximum speed,efficiency and safety.

• Their lightness is a major safetyimprovement, both in terms of carryingand storing the product easily on siteand in reducing accident risk in aerialsituations caused by falling materials.

• Less invasive than threaded rod andenhances the aesthetics of installations.

• Position hangers vertically or at an angleto the suspended object.

• Manufactured to ISO 9002 standards andcarry certificates from UL and SMACNA.

*

* SMACNA Verified - Tested and verified to be an acceptable alternative tothe duct hanger systems prescribed in the HVAC Duct ConstructionStandards Manual, Third Edition 2005, Chapter 5 (Hangers and Supports).

Make One call and Get it All. One stop shopping for the ...€¦ · Make One call and Get it All....

Documents

Transcript of Make One call and Get it All. One stop shopping for the ...€¦ · Make One call and Get it All....