MAJESTIC 8000 WITH CLASSIC 6004 - familypoolfun.com · Majestic step x6 1 15-014 (3/4 in.) 15-015...
Transcript of MAJESTIC 8000 WITH CLASSIC 6004 - familypoolfun.com · Majestic step x6 1 15-014 (3/4 in.) 15-015...
Sand25 lbs
MAJESTIC 8000 WITH CLASSIC 6004
Tools Required (not included)
Contents of SKU box # 8000
x4
105-
012
105-
005
x4 x4
115-
011
1) Insert the two 39" posts into the step recesses and secure them in place with the bolts, washers and nuts provided.
Security strap
A weather resistant padlock is recommended.
PG. 1REV. 02/02/10
x2
x2
x4 x2x2
Contents of the ladder box SKU # 6004
(not incl.)Sand
WARNINGDo not dive or jump from step or ladder.Use BATTERY operated tools to avoid electric shocks.Install step on flat surface, following the manufacturers instructions.Remove step from pool during freezing climate season.Manufacturer cannot be held responsible for injuries caused by abusive use of product. Ask your city about specific regulations that apply to your above-ground pool and ladder.
Maximum functional width is 1/4 inch.
A
SCREW BAG 558-001
x2
105-
012
105-
005
x4 x4
115-
014
(3/4
in.)
x22
125-
035(
1.0
in.)
115-
018
(2 1
/2 in
.)
x2x10
115-
014
(3/4
in.)
105-
012
105-
005
115-
011
x4x4x4
SCREW KIT 140-019
x6x2
2) Slide the two spacers on the top post. Do not secure yet.
3) Insert the handrail over theleft side posts. Secure it using the screws provided. Snap the post cover.
x2
115-
008
(1 3
/4 in
.)
Majestic step
115-
014
x4
x2
5/16"Drill Bit
x1 x1
29.2
5"
35"
67"
115-
015
(1 1
/2 in
.)
x4
115-
018
( 2 1
/2 in
.)
x1
39"
250 industrial blv, St-Germain (Québec), Canada J0C1K0
REV. 25/01/09
B
PG. 2
x8
115-
014
(3/4
IN.)
250 industrial blv, St-Germain (Québec), Canada J0C1K0
D E
*All Step CupTM must be installed*MINIMUM OF 1"
CAUTION*To prevent a pool liner puncture, install all Step Cup™as specified and keep a minimum of 1" inch gap between the pool liner and the rear underside of the step.
1) Slide the platform on the flanged post.
2) Insert the 29.25" hollow post, on the other side, through the spacers and platform.
3) Insert the two small handrails over the posts. Do NOTsecure yet.
C
2) With a flat screwdriver,compress the Step CupTM
mushroom ring while pushing it into the hole.
1) Insert half of the Step CupTM
mushroom in the hole, at a 45 degree angle.
x6
Insert the Step CupTM in the 6 holes under the step.
3) Twist the Step CupTM to ensure that its mushroom has entirely cleared the wall thickness. If it has, the suction cup should rotate freely.
Failing to install the Step cup ™ will greatly reduce the steadiness of the step and will void the manufacturerwarranty.
1) Slowly submerge the step into the pool. Make sure you do not damage the pool liner in the process.
1) Make sure to leave a 1/4" clearance between the bottom spacer, and the top of the step. Secure in place with the screws provided.
12"
2) Mesure 12" between the two spacers. Secure in place with the screws provided.
3) Do NOT secure the platform yet.5) Secure the flanged post with the
bolts, washers and nuts provided.
x2
105-
012
105-
005
x2 x2
115-
008
1
2
3
2) Apply firm pressure on the step to allow the StepCupTM to stick on the pool bottom. Do NOT securethe platform yet.
4
5
4) Once inserted in the spacers, use the 29.25"hollow post as a pivot to slide the flanged poston the other side.Drill (5/16") holes.
1/4"
REV. 02/02/10
x2
105-
012
105-
005
x2 x2
125-
035
115-
014
(3/4
in.)
x11
Security strapx2
1) Once the step is in the pool secure the platform to the top seat (see illustration) using the two straps provided.
SWING THE LADDER UP AND LOCK IN PLACE WHEN THE POOL IS NOTIN USE TO PREVENT DROWNING AND UNAUTHORIZED ENTRY.
WARNING
4) Secure the ladder base to the post with the screws provided.
x6
115-
014
(3/4
IN.)
2) Secure the handrails and platform to the posts with the screws provided.
3) Secure the ladder to the pivot blocks using the bolts, washers and nuts provided.
39'' 40.5''
align
F G
H J
MANUFACTURERWARRANTY
1 year on the ladder and step.
1 year on the hardware. PG. 3
115-
018
(2 1
/2 in
.)
x2
1) Trace a line on each post at 39 inches from the ground for 48'' & 52'' pools. If you have a 54'' pool, trace a line at 40.5'' from the ground.
2) Slide the pivot blocks onto the posts and line up with the traced marks. Secure with the screws provided.
3) Slide the 2 posts through the platform and handrails.
ISand
X4
115-
014
(3/4
in.)
1) Fill the counterweight to the brim with sand.
2) Secure the counterweightcover with the screws provided.
Use sliding lock as a guide to drill hole into ladder in up position.
Use a 5/16'' drill bit.**PADLOCK REQUIRED**
1) Slide the platform downwards and let it sit on the top seat ofthe pool.
This one on the side
OPTIONAL:Once the pool step has been completely assembled and secured to the pool, attach the 2 screws supplied through the platform to the top seat of your pool to provide a more rigid assembly.
250 industrial blv, St-Germain (Québec), Canada J0C1K0
x4
x2
A
115-
014
MAJESTIC 8005
B
REV. 17/02/10 PN: 110-104
2.Insert the handrailinto the recesses.
3.Fasten the hand-rail to the step using the screws, washers and nuts provided.
1.Assemble the twohandrail halves.
Contents of box # sku 8005
x4
x4
115-
010
105-
012
105-
005
WARNINGDo not dive or jump from step or ladder.Use BATTERY operated tools to avoid electric shocks.Install the pool step on a flat surfaceRemove step from pool during freezing climate season.Manufacturer cannot be held responsible for injuries caused by abusive use of product. Ask your city about specific regulations that apply to your above ground pool and ladder.
PG. 1
x6
Sand
(not included)Sand
Tools required (not included)
Majestic step
x6
115-
014
(3/4
in.)
115-
015
(1 1
/2 in
.)
x10
105-
012
105-
005
115-
010
x4x4x4
SCREW KIT 8005MJ08
1) Insert half of the Step CupTM
mushroom in the hole, at a 45 degree angle.
3) Twist the Step CupTM to ensure that its mushroom has entirely cleared the wall thickness. If it has, the suction cup should rotate freely.
CAUTION Failing to install the Step Cup ™ will greatly reduce the steadiness of the step and will void the manufacturer warranty.
2) With a flat screwdriver, compress the Step CupTM
mushroom ring while pushing it into the hole.
x1
x6
Insert the Step CupTM in the 6 holes under the step.
250 Industriel Blv,St-Germain, (Québec),Canada J0C1K0
115-
015
x10
E
TOP SEAT
Spacer block not included
2) Affix the small arm to the handrail vertical post using the 4 screws.
DECKTOP SEAT
DECK
DECK DECK
TOP SEAT
SPACER BLOCKNOT INCLUDED
AFFIX SPACER BLOCKON TOP SEAT
POOL DECK ABOVE POOL TOP SEAT POOL TOP SEAT FLUSH FIT WITH DECK POOL
POOL DECK OFFSET FROM TOP SEATPOOL DECK OFFSET FROM TOP SEAT
1) Apply firm pressure to step bywalking along the steps to engage the Step CupTM .
3) Align the step carefully and fasten the arm to the deck.
1) Fill the counterweight to the brim with sand.
4) Install the counterweightin the step.
MANUFACTURER WARRANTY
1 year on the Majestic pool step.1 year on the hardware.
DCSand
X4
115-
014
(3/4
in.)
1) Slowly submerge the step into the pool. Make sure you do not damage the pool liner in the process.
CAUTION**MINIMUM OF 1"
REV. 17/02/10PN: 110-104 PG: 2
*All Step CupTM must be installed
2) Secure the counterweightcover with the screws provided.
To prevent a pool liner puncture, install all Step CupTM as specified and keep a minimum of 1"inch gap between the pool liner and the rear underside of the step.
250 Industriel Blv,St-Germain, (Québec),Canada J0C1K0