m12.pdf
-
Upload
jamal-jameel -
Category
Documents
-
view
215 -
download
0
Transcript of m12.pdf
-
7/29/2019 m12.pdf
1/36
M12 System
System & Function Component Catalogue
Component Catalogue 2004
-
7/29/2019 m12.pdf
2/36
M12
Component Catalogue 2004 v 0.9
M12 System Notes
General Technical Notes:
his application-orientated documentation Construction System M12 System and Function is intended for specialist users whore familiar with the rules of engineering, the relevant standards and safety regulations and, in particular, with the guidelines and
egulations of fair and exhibition construction.
paceframe structures consisting of M12 System components do not comply with the structural rules or static computations of thetructural MERO Spaceframe Technical Documentation.
ndex of abbreviations used:
AL = aluminiumKF = plastic
T = steelalv. = galvanized
.d.g.p.c. = hot-dip galvanized and powder coated
M12 System - System and Function
ublication for planners and users of MERO Exhibit Systems. Re-printed by MeroForm Systems USA, with express permission of
MERO GmbH & Co. KG, Exhibit Systems. Edition 2004 all rights, including those of reprints in whole or in part, of photo mechanicaleproduction and other copies, require written permission.
MERO GmbH & Co. KG Exhibit Systems & MeroForm Systems USA
We reserve the right to modify construction, materials and dimensions. We assume no liability for values and measurements givenn this publication, particularly in illustrations, drawings, plans, calculations, and tables, unless they have been explicitly declared
inding in writing.
-
7/29/2019 m12.pdf
3/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Standard M12 Node
For the design and assembly of all regular modules and standardized space-framesstandard nodes are needed. This standard node is also used for the various conneangles of Frame Girders. Only few exceptions need special Nodes.
Each Node has 18 tap holes, angles between tap hole faces 45, 60, 90,120,135, 18
Face to face diameter of 46mm. Made of steel or aluminum, steel Nodes are chrplated or powder coated and aluminum Nodes are powder coated, anodized
chromed.
Colors may vary slightly.Special colors available on request.
Standard Nodes M12/Materials/Finish
Standard Node 49, 5/46 M12 ST/AL
Steel (23 kgs.) Aluminum (8 kgs.)
Part # Price Part # Price
Chrome 20054 $23.53 20167 $22.86
Powder Coated 20055 $22.15 20168 $21.48
P.C. White (RAL 9016) 20056 $22.15
P.C. Black (RAL ????)
Clear Anodized (E6/EV1) 20169 $21.48
-
7/29/2019 m12.pdf
4/36
M12
Component Catalogue 2004 v 0.9
Node Geometry
The MERO node is derived from the cube. It
has 26 faces, i.e. 8 equilateral triangles and 18squares.However, for practical and economical reasons
the node is actually made from a ball-shapedblank with rounded off corners, thus giving 18
circular cutting planes.
These alone are important for practicalapplication. The circular planes are at a uniform
distance to the centre of the ball. In the middleof each there is a tap hole size M12. The axes ofall tap holes intersect in the centre of the node.
Depending on the position of the cutting planesangles of 45, 60, 90, 120, 135 and 180 will
result.
-
7/29/2019 m12.pdf
5/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Special Nodes M12 Ste
Part # / Finish
Price
kgs. Description
504197 Chrome$27.06
504198 Powder Coated
$25.67
.43 Half Node M12 STWith 13 tap holes. Because of its larger contact surface the
half node can be positioned more easily and provides a safe ansimple assembly of the spaceframe. A gap-free cladding of th
M12 structure is possible since node surface and tube form aplane.
20064 Chrome
$26.4020063 Powder Coated
$25.71
.27 Node M12, Milan 49,5/46 M12 ST
With 14 tap holes. A diagonal tap hole row with at anglescreates the at version of the half-octahedron space-frame typ
Milan. The two diagonal tap hole rows are turned at 45 toeach other in order to allow the connection of space diagonaland surface diagonal on one node (as mast node). The use of
surface diagonal in the horizontal position is not possible.
21400 Chrome
$34.8521402 Powder Coated
$38.99
.31 Vario Node 49,0/46 M12 ST
With 5 tap holes, 3 of which have variable angles around theequator line. The minimum horizontal plane angle is 60.
20065 Chrome$13.27
20066 Powder Coated$12.86
.08 Cube-type Node M12 STWith 6 tap holes, connecting an angle of 90, 28 mm dia.
between tap hole faces.
If used with standard tubes, the system dimension is reduced b
18 mm.
20070 Chrome$17.39
20071 Powder Coated$16.70
20072 P.C. White (RAL 9016)$16.70
.15 Ring Node 45 22 M12 STHeight 22 mm, 8 tap holes on the perimeter.
Connecting angle 45, height adjustable on the tube by meansof set-screw M12. Only for tubes of 22 mm dia., complete with
set-screw.
20078 Chrome
$17.3320079 Powder Coated
$16.64
20080 P.C. White (RAL 9016)$16.64
.13 Ring Node 45 22 M12 ST open
Height 22 mm, 5 tap holes on the perimeter angled 45. Forapplication after installation of tube the disc-type node isslipped over sleeve to position on tube and xed by set-screw.
Application only for tubes 22 mm dia.
-
7/29/2019 m12.pdf
6/36
M12
Component Catalogue 2004 v 0.9
Special Nodes M12 Steel
Part # / Finish
Price
kgs. Description
20057 Chrome$26.40
20058 Powder Coated
$25.58
.24 Mast Node 49,5/46 M12 STWith 18 tap holes. Referring to the vertical main axis the two
opposite diagonal tap hole rows (4 tap holes) are rotated by 45.This node is necessary if surface diagonals and space diagonals
have to be connected to one node.
20061 Chrome
$28.2120062 Powder Coated
$27.39
.27 Triangle Node 49,5/46 M12 ST
With 14 tap holes. The two vertical tap holes on both sides allowin a space frame structure with triangular module and reduced
construction depth the connection of verticalsupports or suspensions on both sides.
-
7/29/2019 m12.pdf
7/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Special Nodes M12 Ste
Connecting Angles of Ring Nodes
Applications - Special Nodes
Please note: When dismantling the structure, one of the connecting pieces must be xed horizontally with a grub screw
(supplied), before the vertical tubes are loosened.
-
7/29/2019 m12.pdf
8/36
M12
Component Catalogue 2004 v 0.9
Tubes 22M12, Materials and Finishes
Tubes 22M12, 22 mm tube diameter with M12 bolt. Materials: steel
and aluminium.
All steel tubes will be supplied chromed or powder coated.
All aluminium tubes will be supplied powder coated or mat anodized
in E6/EV1 aluminum.
L1 System size
he length of the MERO tubes grows in a geometric progression by
he factor2. It is described as system dimension L1 and is measured
rom node axis to node axis. By adding the same tube lengths, an
xact module dimension is achieved. The next largest tube length is
lways equal to the length of the side opposite the right angle of the
preceding right-angled triangle in a row of right-angled triangles.
-
7/29/2019 m12.pdf
9/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Tubes 22 M12, Materials and Finish
Steel Tubes
Part # Description Finish kgs. Price
20081 Tube 250mm 22x 1,0M12 Chrome 0.25 $20.55
20082 Tube 250mm 22x 1,0M12 Powder Coat 0.25 $18.90
20083 Tube 250mm 22x 1,0M12 P.C. White (RAL 9016) 0.25 $18.90
20084 Tube 353mm 22x 1,0M12 Chrome 0.305 $22.70
20085 Tube 353mm 22x 1,0M12 Powder Coat 0.305 $20.63
20086 Tube 353mm 22x 1,0M12 P.C. White (RAL 9016) 0.305 $20.63
20087 Tube 500mm 22x 1,0M12 Chrome 0.375 $26.00
20088 Tube 500mm 22x 1,0M12 Powder Coat 0.375 $22.42
20089 Tube 500mm 22x 1,0M12 P.C. White (RAL 9016) 0.375 $22.42
20090 Tube 707mm 22x 1,0M12 Chrome 0.48 $30.27
20091 Tube 707mm 22x 1,0M12 Powder Coat 0.48 $25.17
20092 Tube 707mm 22x 1,0M12 P.C. White (RAL 9016) 0.48 $25.17
20093 Tube 791mm 22x 1,0M12 Chrome 0.52 $31.81
20094 Tube 791mm 22x 1,0M12 Powder Coat 0.52 $25.6020095 Tube 791mm 22x 1,0M12 P.C. White (RAL 9016) 0.52 $25.60
20096 Tube 1000mm 22x 1,0M12 Chrome 0.625 $35.94
20097 Tube 1000mm 22x 1,0M12 Powder Coat 0.625 $28.36
20098 Tube 1000mm 22x 1,0M12 P.C. White (RAL 9016) 0.625 $28.36
20100 Tube 1414mm 22x 1,0M12 Chrome 0.82 $43.46
20101 Tube 1414mm 22x 1,0M12 Powder Coat 0.82 $32.98
20102 Tube 1414mm 22x 1,0M12 P.C. White (RAL 9016) 0.82 $32.98
20103 Tube 2000mm 22x 2,0M12 Chrome 1.96 $57.28
20104 Tube 2000mm 22x 2,0M12 Powder Coat 1.96 $49.14
20105 Tube 2000mm 22x 2,0M12 P.C. White (RAL 9016) 1.96 $49.14
Aluminum Tubes
Part # Description Finish kgs. Price
20180 Tube 250mm 22x 1,0M12 E6/EV1 0.185 $18.59
20179 Tube 250mm 22x 1,0M12 Powder Coat 0.185 $18.59
20183 Tube 353mm 22x 1,0M12 E6/EV1 0.205 $20.18
20182 Tube 353mm 22x 1,0M12 Powder Coat 0.205 $20.18
20186 Tube 500mm 22x 1,0M12 E6/EV1 0.265 $21.93
20185 Tube 500mm 22x 1,0M12 Powder Coat 0.27 $21.95
20189 Tube 707mm 22x 1,0M12 E6/EV1 0.265 $24.27
20188 Tube 707mm 22x 1,0M12 Powder Coat 0.265 $24.27
20192 Tube 791mm 22x 1,0M12 E6/EV1 0.275 $24.58
20191 Tube 791mm 22x 1,0M12 Powder Coat 0.275 $24.58
20195 Tube 1000mm 22x 1,0M12 E6/EV1 0.315 $27.07
20194 Tube 1000mm 22x 1,0M12 Powder Coat 0.315 $27.07
20198 Tube 1414mm 22x 1,0M12 E6/EV1 0.387 $31.20
20197 Tube 1414mm 22x 1,0M12 Powder Coat 0.387 $31.20
20201 Tube 2000mm 22x 1,0M12 E6/EV1 0.5 $43.33
20200 Tube 2000mm 22x 1,0M12 Powder Coat 0.5 $43.33
-
7/29/2019 m12.pdf
10/36
0 M12
Component Catalogue 2004 v 0.9
1/4 Circle, Hinged, and Hinged Slotted Tubes 22 M12, Steel
1/4 Circle Tubes 22M12 ST
Part # Description Finish kgs. Price
20126 Tube 1/4R 500mm 22x 1,0M12 Chrome 0.85 $87.69
20127 Tube 1/4R 500mm 22x 1,0M12 Powder Coat 0.85 $68.39
501860 Tube 1/4R 707mm 22x 1,0M12 Chrome 1.2 $102.01
20129 Tube 1/4R 707mm 22x 1,0M12 Powder Coat 1.2 $74.99
20130 Tube 1/4R 1000mm 22x 1,0M12 Chrome 1.6 $123.01
20131 Tube 1/4R 1000mm 22x 1,0M12 Powder Coat 1.6 $86.34
Hinged Tubes 22M12 ST
Part # Description Finish kgs. Price
20106 Hinged tube 500mm 22x 2,0M12 Chrome 0.78 $171.38
20107 Hinged tube 500mm 22x 2,0M12 Powder Coat 0.78 $171.93
20108 Hinged tube 707mm 22x 2,0M12 Chrome 1.08 $174.75
20109 Hinged tube 707mm 22x 2,0M12 Powder Coat 1.08 $175.58
20110 Hinged tube 1000mm 22x 2,0M12 Chrome 1.25 $179.00
20111 Hinged tube 1000mm 22x 2,0M12 Powder Coat 1.25 $179.97
20112 Hinged tube 1414mm 22x 2,0M12 Chrome 1.63 $186.14
20113 Hinged tube 1414mm 22x 2,0M12 Powder Coat 1.63 $187.65
20114 Hinged tube 2000mm 22x 2,0M12 Chrome 2.2 $194.29
20115 Hinged tube 2000mm 22x 2,0M12 Powder Coat 2.2 $197.73
Hinged Slotted Tubes 22M12 ST
Part # Description Finish kgs. Price
20634 Hinged slott. tube 500mm 22M12 Chrome 0.76 $174.1920635 Hinged slott. tube 500mm 22M12 Powder Coat 0.76 $174.33
20636 Hinged slott. tube 707mm 22M12 Chrome 1.08 $179.99
20637 Hinged slott. tube 707mm 22M12 Powder Coat 1.08 $180.96
20638 Hinged slott.tube 1000mm 22M12 Chrome 1.22 $187.57
20639 Hinged slott.tube 1000mm 22M12 Powder Coat 1.22 $188.40
20640 Hinged slott.tube 1414mm 22M12 Chrome 1.58 $198.76
20641 Hinged slott.tube 1414mm 22M12 Powder Coat 1.58 $200.14
20642 Hinged slott.tube 2000mm 22M12 Chrome 2.11 $210.89
20643 Hinged slott.tube 2000mm 22M12 Powder Coat 2.11 $215.17
-
7/29/2019 m12.pdf
11/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Hinged Tubes and Hinged Slotted Tubes 22 M12, Ste
Stop Tubes andSlotted Stop Tubes 45 and 90
Lengths as listed on p. 14 areavailable on request.
Cylinder Lock for Glass Door,
With individual key.
Part # 10012
Glass Cut6 mm crystal mirror glass pane, edgescut and polished, hinged left and
right.
-
7/29/2019 m12.pdf
12/36
2 M12
Component Catalogue 2004 v 0.9
Accessories
Adjustable Foot D50x8 mm M12
Pack. 10 ea., 50 mm , used as base or top plate or spacer to the wall. Length ofthe threaded bolt 45 mm. Fitted using wrench SW19.5
Part # 20368Finish: Chrome
kgs. 0.07$28.67
Bottom Plate D100x8 mm M12 ST
100 mm , for xed space frame structures to the oor.
Part # 20372 Part # 20373
Finish: Galv. Finish: Powder Coated
kgs. 0.47 kgs. 0.47
$18.52 $20.72
Castor Wheel M12 KF50 mm , height 64 mm, carrving capacity 50 kp. Standard packing 4 pieces.(Fitted using wrench SW17)
Part # 20658Finish: Black Plastic
kgs. 0.11$35.31
Foot Plate M12 L500
For free-standing single walls, information boards etc. Connection for tube22M12.
Part # 21786 Part # 21785
Finish: Chromed Finish: Powder Coated
kgs. 2.70 kgs. 2.70
$90.22 $81.40
Threaded Bolt M 12/M 6 ST,
Pack. 20 ea., for wall or ceiling attachement of the construction onto the node by
means of dowel (wall anchor).
Part # 20676Finish: Galvanizedkgs. 0.01
$19.04
-
7/29/2019 m12.pdf
13/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessor
Threaded Bolt with Hook, M12/M5 ST
Pack. 20 ea., for attachment or suspension of decoration onto the node.
Part # 20667
Finish: Galvanizedkgs. 0.01
$50.93
Eyebolt M12x35 DIN 444
For the suspension of space frames.
Part # 10623
Finish: Galvanizedkgs. 0.04
$5.53
Connecting Piece M12/M12, pivotable
Pack. 10 ea., for connection of two nodes on preassembled spaceframe parts.
(Fitted using wrench SW19.5)
Part # 20669
Finish: Galvanizedkgs. 0.05
$77.79
Connecting Piece M10/M12 ST
Pack.10 ea., with pivotable connection, is used for the connection of space frame-work to substructures with M10 connection thread. (Fitted using wrench SW19.5)
Part # 20388
Finish: Galvanizedkgs. 0.09$125.10
-
7/29/2019 m12.pdf
14/36
4 M12
Component Catalogue 2004 v 0.9
Accessories
Suspension Clamp 22 mm ST
pack. 20 ea., for 22, 30 or 42 mm tube dia., for vertical attachment of panels in front of the modular frame.
Part # 20659 Part # 20381
Finish: A2 Polished Finish: Powder Coated
kgs. 0.03 kgs. 0.03
$54.01 $74.15
Support Clamp 22 mm ST
pack. 20 ea., for 22, 30 or 42 mm tube dia., for vertical attachment of panels in front of the modular frame.
Part # 20662 Part # 20384
Finish: A2 Polished Finish: Powder Coated
kgs. 0.03 kgs. 0.03
$67.77 $84.88
Clip 45, 60 and 90 22 mm STpack. 20 ea., for 22 or 30 mm tube dia., bearing capacity up to 20 kp.
45 22 mm 60 22 mm 90 22 mm
Part # 20374 Part # 20375 Part # 20376 Part # 20377 Part # 20378 Part # 20379
Finish: Galvanized Finish: P.C. Finish: Galvanized Finish: P.C. Finish: Galvanized Finish: P.C.
kgs. 0.05 kgs. 0.05 kgs. 0.06 kgs. 0.06 kgs. 0.06 kgs. 0.06
$36.73 $54.10 $36.75 $54.12 $36.73 $54.10
Clip 90 22 ST
pack. 50 ea., for 22 mm tube dia., bearing capacity up to 10 kp.
Part # 20666Finish: Nickel-plated
kgs. 0.01$146.45
-
7/29/2019 m12.pdf
15/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessor
-
7/29/2019 m12.pdf
16/36
6 M12
Component Catalogue 2004 v 0.9
Accessories
he panel is tted after the framework has been assembled.
he rigid panel can, in some cases, replace a diagonal tube.he clip is tightened with the wrench SW 4, which also xes the
anel element.
Clip 22/4-10mm and 30/4-10mm KF
Pack. 50 ea., for 22 or 30 mm dia. tubes, for attachment of panels 4 to 10 mm thick, complete withwrench SW4. The bearing capacity is 20 kp.
Part # 20677Finish: Clear Plastic
kgs. 0.02$67.05
-
7/29/2019 m12.pdf
17/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessor
Clip 22mm /4-6mm /6-8mm /8-10 KF
Pack. 100 ea., for attachment of panels of 4-6 mm, 6-8 mm and 8-10 mm thickness, to 22 mm tube dia.,bearing capacity 15 kp. The panel is tted after the framework has been assembled.
4-6mm Panel 6-8mm Panel 8-10mm Panel
Part # 20672 Part # 20673 Part # 20675
Finish: Clear Plastic Finish: Clear Plastic Finish: Clear Plastic
kgs. 0.01 kgs. 0.01 kgs. 0.01
$47.27 $47.27 $47.27
Glass Corner Clamp M12, Type ll KF
Screwed to outside of structure, pack 20 ea., for xing of panels, max. 6 mm thick in horizontal and
vertical direction in the diagonal hole of the node, complete with wrench SW4, bearing capacity 20 kp.
The glass panel is tted after the framework has been assembled.
Part # 20680Finish: Clear Plastic
kgs. 0.02$33.77
-
7/29/2019 m12.pdf
18/36
8 M12
Component Catalogue 2004 v 0.9
Accessories
-
7/29/2019 m12.pdf
19/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessorie
Glass Corner Clamp 22,0mm KF
Pack 20 ea., for xing of panels, 5-8 mm thick in horizontal and vertical direction, for use with round sleevtube and cube node. Complete with wrench SW4, bearing capacity 20 kp.
The glass pane is tted after assembly of the framework.
Part # 20679
Finish: Clear Plastickgs. 0.01
$33.73
Corner Connector Type I KF
Pack. 20 ea., for sliding door prole.
Part # 20686 Part # 20687
Finish: Chrome Plastic Finish: White Plastic
kgs. 0.01 kgs. 0.01
$45.51 $35.78
Corner Connector Type II KF
Pack. 20 ea., for glazing prole.
Part # 20694 Part # 20695
Finish: Chrome Plastic Finish: White Plastic
kgs. 0.01 kgs. 0.01
$45.51 $35.78
Cladding Connector M12
Pack 10 ea., for xing of lightweight panels of max. 16 mm thickness in front of the structure.
Part # 50559Finish: Grey Plastic
kgs. 0.03$205.75
-
7/29/2019 m12.pdf
20/36
0 M12
Component Catalogue 2004 v 0.9
a) b)
a) b)
Cutting dimensions for the sliding doorframe and insertion prole:
a) for 22 mm tube diameterb) for 30 mm tube diameter
Cutting dimension for the glazingframe:
a) for 22 mm tube diameterb) for 30 mm tube diameter
Accessories
-
7/29/2019 m12.pdf
21/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessorie
Sliding Door Prole AL
For the construction of sliding door frames with corner connectors type I KF (p. 22).For 6 mm thickness panel. Cutting dimensions of the frame: see p. 25.
Part # 20685 Part # 20683 Part # 20688
Finish: Chrome Finish: E6/EV1 Finish: Powder Coat
kgs. 1.15 kgs. 1.15 kgs. 1.15
$261.96 $135.64 $207.57
Glazing Prole AL
For the construction of glazing frames together with corner connectors type II KF (p. 24).For 6 mm panel thickness. For cutting dimensions of the frame: see p. 25.
Part # 20692 Part # 20696 Part # 20693
Finish: Chrome Finish: E6/EV1 Finish: Powder Coat
kgs. 1.01 kgs. 1.01 kgs. 1.01
$249.75 $116.19 $163.61
Insertion Prole 1250 mm KF
Part # 21450Finish: Light Grey Plastic
kgs. 0.05$2.12
-
7/29/2019 m12.pdf
22/36
2 M12
Component Catalogue 2004 v 0.9
Accessories
a)
b)
c)
By means of the asymmetric groove prole the accurately cut panel can be subsequently
pressed into the module of frameworks consisting of 22 mm or 30 mm diameter.
a) The panel is basically loaded on one side only, from that side of the panel on which the
solid part of the prole is lying. If the panel is insertedhorizontally, the solid part of the prole is always on top
b) Insertion in structures 22 M12: Minimum angle between 2 panels 90.
The groove prole is stuck in with cold glue. Width of groove B: for solid wood = 3.0 mm,for chipboard = 2.8 mm, depth of groove 10 mm. Minimum panel thickness 19 mm.
Groove Prole 2500 mm KF
Pack. 50 ea., length 2500 mm, for xing of wood panels, 19 mm thick or more, in horizontal and vertical direc-
tion. Special colors on request (minimum ordering quantity = 2500 lin.mtrs.)
Part # 20684 Part # 20682
Finish: Light Grey Plastic Finish: White Plastic
kgs. 0.35 kgs. 0.35
$293.50 $293.50
-
7/29/2019 m12.pdf
23/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessor
-
7/29/2019 m12.pdf
24/36
4 M12
Component Catalogue 2004 v 0.9
Accessories
Spider Fixing S 4 complete
Pack. 4 ea., with 4 brackets, for theattachment of panels or glass elements infront of the construction.
stainless steel, kgs 0.256
Part # 502129,$188.49
Spider Fixing S 3 complete
Pack. 4 ea., with 3 brackets.stainless steel, kgs 0.229
Part # 502128
$152.54
Spider Fixing S 2 complete
Pack. 4 ea., with 2 brackets.stainless steel, kgs 0.186
Part # 502127$112.40
Spider Fixing S 1 complete
Pack. 4 ea., with 1 bracket.stainless steel, kgs 0.139
Part # 502126
$74.99
Panel sizes, technical sheets available on
request!
Countersunk screw M5x20 DIN7991 A1
art #: 502117 - $0.28Conical spring washer 24x6 A2
art #: 502116 - $5.51Washer D23/14,5x2mm, transparent
art #: 502115 - $1.38Bolt M12/M5 x 16,5mm
art #: 502107 - $2.76Cross shaped xture 4art #: 502121 - $19.99
Countersunk screw M12x20 A2art #: 502109 - $0.28
Washer D18/12,2mm A2art #: 502114 - $2.76
-
7/29/2019 m12.pdf
25/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessor
Wrench SW 17, 19.5, 28.5, 30
SW17 (10) for groovetubes
SW19.5 (10) for tubesdia. 22mm
SW28.5 (1) for dometubes dia. 30mm
SW30 (5) for expo oorpedestals
Part # 20698 Part # 20699 Part # 20700 Part# 20791
Finish: Galvanized Finish: Galvanized Finish: Galvanized Finish: Galvanized
kgs. 0.07 kgs. 0.08 kgs. 0.14 kgs. 0.26
$48.32 $48.37 $14.87 $50.24
Hexagonal Screw Driver SW 4
Pack. 4 ea.
Part # 20702Finish: N/Akgs. 0.05
$27.97
Allen Wrench SW 5, 6, 8, 10 DIN 911
Package of 10
SW 5 SW 6 SW 8 SW 10
Part # 21464 Part # 21465 Part # 21466 Part# 21467
Finish: Nickel Finish: Nickel Finish: Nickel Finish: Nickel
kgs. 0.03 kgs. 0.03 kgs. 0.03 kgs. 0.03
$9.62 $20.39 $21.10 $28.19
-
7/29/2019 m12.pdf
26/36
6 M12
Component Catalogue 2004 v 0.9
Girders 22 and 42 M12
Material and Finishes:
Steel 22 mm tube diameter with MEROconnection ttings M12 at each end.
The Girders 22 M12 are available in chrome or
powder coated nish.
System Sizes:The length of the girder is designated by sys-
tem size L1 which is measured from one nodeaxis to the next. Special lengths are available on
request.
M12 System girders are light weight elements
produced in series with typical MERO featuresand special
characteristics: high stability with a minimum of
material Iarge module lengths and span widths
short assembly time Iow construction height great design exibility due to the
MERO geometry compatibility with all M12 System
programs
-
7/29/2019 m12.pdf
27/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Girder 22 M12
Description Part #: chrome painted kgs.
Girder Duo 500 mm 22 M12 ST 20509 20510 0,92Girder Duo 707 mm 22 M12 ST 20511 20512 1,14
Girder Duo 1000 mm 22 M12 ST 20513 20514 1,44Girder Duo 1414 mm 22 M12 ST 20515 20516 2,02
Girder Duo 2000 mm 22 M12 ST 20517 20518 2,80Girder Duo 2250 mm 22 M12 ST 20520 20519 3,02
Girder Duo 2500 mm 22 M12 ST 20521 20522 3,56Girder Duo 3000 mm 22 M12 ST 20523 20524 4,00Girder Quadro 1000 mm 22 M12 ST 20527 20528 3,32
Girder Quadro 2000 mm 22 M12 ST 20529 20530 6,30Girder Quadro 2250 mm 22 M12 ST 20531 20532 7,10
Girder Quadro 2500 mm 22 M12 ST 20533 20534 7,75Girder Quadro 3000 mm 22 M12 ST 20535 20536 9,20
Girder Trio A 1000 mm 22 M12 ST 20537 20538 2,55Girder Trio A 2000 mm 22 M12 ST 20539 20540 4,85
Girder Trio A 3000 mm 22 M12 ST 20541 20542 7,20
Bottom Plate 250x250x20 mm
for GirderPart # 21636 h.d.g., kgs. 9,67
Countersunk Screw M20x50 mmDIN 7971 ST
Part # 21667 galv., kgs. 0,12
Girders 22 and 42 M
-
7/29/2019 m12.pdf
28/36
8 M12
Component Catalogue 2004 v 0.9
Accessories for Girders 22 M12
Threaded Sleeve hexagonal
2xM12 ST, For connection or extension of frame girders in place of the node if lateral connection is notrequired.
Part # 20495 Part # 20496
Finish: Chrome Finish: Powder Coat
kgs. 0.08 kgs. 0.08
$83.42 $83.42
Connection Kit M12 22,5 ST
For designing barrel vault structures with frame girders Duo. Complete with distance bush, and two specialnodes.
Part # 20499 Part # 20500
Finish: Chrome Finish: Powder Coat
kgs. 0.60 kgs. 0.60
$99.94 $98.85
-
7/29/2019 m12.pdf
29/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessories for Girders 22 M
Tube 1/8K 250mm 22x1,0 M12 ST
For designing decorative barrel vaults or curved structures with a 135 angle for typeDuo and Quadro 22 M12.
Part # 20503 Part # 20504
Finish: Chrome Finish: Powder Coat
kgs. 0.19 kgs. 0.19
$46.10 $45.00
Shelf for Leaets
Without xing parts, located between two frame girders Duo 22 M12 on two parallel
wires.
Part # 20391Finish: Clear Acrylickgs. 0.54
$22.40
Shelf for Leaets 320x273 mm
Complete with cap screws M12 for xing onto the node.
Part # 20689Finish: Clear Acrylic
kgs. 0.65$43.90
-
7/29/2019 m12.pdf
30/36
0 M12
Component Catalogue 2004 v 0.9
Slotted Tubes 22 M12, Steel and Accessories
Slotted Tubes
They have four rows of slots around the circumference,spaced 90, to carry slotted tube accessories.
For further additions refer to standard tubes M12 andstandard accessories.
Slotted tubes can be supplied chromed and powder
coated.
Slotted Tubes
Part # Description Finish kgs. Price
20624 Slott. tube 500mm 22x 2,0M12 Chrome 0.538 $31.46
20625 Slott. tube 500mm 22x 2,0M12 Powder Coat 0.538 $29.95
20626 Slott. tube 707mm 22x 2,0M12 Chrome 0.785 $38.77
20627 Slott. tube 707mm 22x 2,0M12 Powder Coat 0.785 $36.43
20628 Slott. tube 1000mm 22x 2,0M12 Chrome 1 $48.43
20629 Slott. tube 1000mm 22x 2,0M12 Powder Coat 1 $44.85
20630 Slott. tube 1414mm 22x 2,0M12 Chrome 1.361 $62.25
20631 Slott. tube 1414mm 22x 2,0M12 Powder Coat 1.361 $57.15
20632 Slott. tube 2000mm 22x 2,0M12 Chrome 1.888 $78.78
20633 Slott. tube 2000mm 22x 2,0M12 Powder Coat 1.888 $74.78
Shelf Frame 1000 mm ST
Oval tube 30 x 15, used in horizontal position and with an angle of 15.
Part # 20762 Part # 20415
Finish: Chrome Finish: Powder Coat
kgs. 2.25 kgs. 2.40
$63.24 $70.71
-
7/29/2019 m12.pdf
31/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Accessor
Bracket 300 mm ST
Pack. 4 ea., used in horizontal position or with an angle of 15.
Part # 20753 Part # 20408
Finish: Chrome Finish: Powder Coat
kgs. 0.23 kgs. 0.25
$51.63 $73.49
Support 300 mm ST
For bracket, pack 2 ea., with xing material.
Part # 20754 Part # 20409
Finish: Chrome Finish: Powder Coat
kgs. 0.18 kgs. 0.18
$35.45 $48.27
Connecting Rods 1000 mm ST
Pack. 4 ea., to make shelf frames in conjunction with brackets 300 mm or inclined braets 30.
Part # 20756 Part # 20411
Finish: Chrome Finish: Powder Coat
kgs. 0.62 kgs. 0.62
$38.13 $50.26
Leaet Shelf 1000 mm acrylic
For inclined bracket, pack 2 ea.
Part # 20760
Finish: Clear Acrylickgs. 2.29
$127.42
Square Perforated Plate
Pack. 2 ea., for shelf frame in horizontal position and at an angle of 15 with brackets
or at an angle of 30 with inclined brackets.
Part # 20758
Finish: Chromekgs. 1.95$147.25
Inclined Bracket 30 ST
Pack. 4 ea., to make shelf frames with an angle of 30.
Part # 20755 Part # 20410
Finish: Chrome Finish: Powder Coat
kgs. 0.27 kgs. 0.25$38.13 $50.26
-
7/29/2019 m12.pdf
32/36
2 M12
Component Catalogue 2004 v 0.9
Sizes of Glass Panes:
System size 1.000 mLength 996 mm, width 300 mm.
Accessories
Sizes of Glass Panes:
System size 1.000 mLength 965 mm, width 310 mm.Corner rounding R 5 mm.
Sizes of Glass Panes:System size 1.000 m
Length 997 mm, width 299 mm.
System size 0.707 mLength 704 mm, width 299 mm.
Bracket with M12 Thread 22
Pack. 4 ea., for standard tubes.
Part # 20766 Part # 20419
Finish: Chrome Finish: Powder Coat
kgs. 0.04 kgs. 0.04
$95.01 $79.74
Glass Pane Holder 90 22 ST
With glass shelf rest, pack. 4 ea., for slotted tubes 22 M12.
Part # 20768 Part # 20420
Finish: Chrome Finish: Powder Coat
kgs. 0.02 kgs. 0.03
$70.94 $70.98
Glass Shelf Rest PVC
Pack. 100 ea.
Part # 20772Finish: Clearkgs. 0.002
$11.10
-
7/29/2019 m12.pdf
33/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
Aluminum Dome 30 M
Iko 2
Iko 4
Iko 6
Iko 8
Standard Sizes for Each Dome Type.
Complete hemispheres are supplied as standard. Additionnally, a ring segment(= dome segment) can be supplied for each dome, which increases the overallheight. This is of advantage for the standing height at the edges of the dome,
especially in the case of smaller models.
GeometryThe basic geometric shape from which the M12 light weight domes are
generated, is the icosahedron (20 faces and 12 vertecies). By dividing each faceof the icosahedron (i.e. two, four, six and eight times) with additional tubes and
nodes, the curved network geometry of the M12 light weight dome results.
IKO 2 from 56 m,
IKO 4 from 510 m,IKO 6 from 815 m and
IKO 8 from 1116 mspherical diameters.
All dimensions are standard dimensions measured from node axis to node axis.
Material and Finishes
Nodes and tubes in aluminum, anodized E6 C-0 or powder coated.
InstallationSimple and quick because of the
numbered parts and exact erection plans.
Cladding
With readily available panel materials and the M12 attachment hard ware. With
M12 cladding elements and for openair exhibits, with the M12 fabric cladding.
Segments, Complete Spheres, Cladding and Accessories,
such as cladding panels, M12-fabric cladding, supports and bottom plates canbe delivered on request.
Appendix C
gives comprehensive information about the design and application methodfor M12 lightweight domes.
-
7/29/2019 m12.pdf
34/36
4 M12
Component Catalogue 2004 v 0.9
Aluminum Dome 30 M12
Description Finish E6/EV1 Powder Coat kgs.
Part # Price Part # Price
Hemisphere IKO 2, D 5000mm AL 21272 $6,213.46 21274 $6,735.73 61
Hemisphere IKO 2, D 6000mm AL 21273 $6,432.83 21275 $7,047.20 68
Hemisphere IKO 4, D 5000mm AL 21276 $20,809.01 21282 $21,953.34 164
Hemisphere IKO 4, D 6000mm AL 21277 $21,270.69 21283 $22,591.68 178
Hemisphere IKO 4, D 7000mm AL 21278 $21,743.74 21284 $23,233.82 191
Hemisphere IKO 4, D 8000mm AL 21279 $22,158.95 21285 $23,840.95 197
Hemisphere IKO 4, D 9000mm AL 21280 $22,678.61 21286 $24,514.30 218
Hemisphere IKO 4, D 10000mm AL 21281 $23,147.99 21287 $25,144.94 232
Hemisphere IKO 6, D 8000mm AL 21288 $45,887.20 21296 $48,206.66 371
Hemisphere IKO 6, D 9000mm AL 21289 $46,602.70 21297 $49,229.42 391
Hemisphere IKO 6, D 10000mm AL 21290 $47,345.20 21298 $50,271.34 412
Hemisphere IKO 6, D 11000mm AL 21291 $48,068.41 21299 $51,294.24 432
Hemisphere IKO 6, D 12000mm AL 21292 $48,787.57 21300 $52,312.96 451
Hemisphere IKO 6, D 13000mm AL 21293 $49,518.47 21302 $53,343.41 471
Hemisphere IKO 6, D 14000mm AL 21294 $50,260.97 21303 $54,370.07 492
Hemisphere IKO 6, D 15000mm AL 21295 $50,976.48 21304 $55,408.09 512
Hemisphere IKO 8, D 11000mm AL 21305 $81,074.34 21311 $85,352.40 663
Hemisphere IKO 8, D 12000mm AL 21306 $81,978.42 21312 $86,655.84 690
Hemisphere IKO 8, D 13000mm AL 21307 $82,893.99 21313 $87,940.11 716
Hemisphere IKO 8, D 14000mm AL 21308 $83,809.55 21314 $89,224.39 742
Hemisphere IKO 8, D 15000mm AL 21309 $84,733.07 21315 $90,531.86 770
Hemisphere IKO 8, D 16000mm AL 21310 $85,656.30 21316 $91,831.50 798
-
7/29/2019 m12.pdf
35/36
MeroForm Systsms USA
+1.714.974.8544 www.MeroForm.us
-
7/29/2019 m12.pdf
36/36
MeroForm Systems USA is the exclusive importer and fabricatorin the United States for MERO Exhibit Systems.
MeroForm Systems USA429 West Levers Place, Orange, CA 92867
tel +1.714.974.8544 fax +1.714.283.2494www.MeroForm.us