Looking back and ahead at 6U CompactPCI...

12
6U CompactPCI PRODUCT GUIDE g T his month’s issue includes a 6U CompactPCI Product Guide, and I’d like to take the opportunity to reflect a bit on the success and evolution of that technology. Back in the 1994 time frame when CompactPCI was first being devel- oped, it began as 3U-only technology. It used the same Eurocard mechanics that were popularized by VME and an IEC standardized, high- density, high-speed connector available from a number of vendors suitable for 33 MHz PCI signaling. That connector was selected by the engineers at Ziatech, with help from Mike Munroe, then at ERNI. The majority of VME designs were 6U, and based on this, I was among a number of folks that argued for adding the 6U CompactPCI form factor. The 6U form factor presented some challenges and opportunities. One challenge was that the insertion and extraction forces were quite high when the entire rear of the card was populated with connectors. Fortunately, the IEEE standards for Eurocards evolved, and injector/ejector handles that pro- vided leverage became available. Eike Waltz, then at Rittal, was instrumental in bringing that to the table. Two of the opportunities that came along with the extra connectors were a clean way to add secondary buses like the H.110 telephony bus to the backplane and the ability to route I/O out the rear through rear transition modules. PICMG has developed quite a number of subsidiary specifications defining the interoperable use of the extra backplane pins made possible with the 6U form factor. Both of these features have played a major part in CompactPCI’s success. The next major evolution of 6U CompactPCI came with the PICMG 2.16 Packet Switched Backplane standard, which was originally conceived by John Peters and his team at Performance Technologies. PICMG 2.16 interconnected a shelf full of CompactPCI single board computers via redundant Ethernet switches, also in the 6U CompactPCI form factor. This dramatically increased usable backplane bandwidth and provided redundancy. PICMG 2.16 paved the way for AdvancedTCA and was the industry’s first open standard for the switched serial interconnect standards we see popping up in many places. By JOE PAVLAT Looking back and ahead at 6U CompactPCI

Transcript of Looking back and ahead at 6U CompactPCI...

Page 1: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

CompactPCI and AdvancedTCA Systems February 2008 31

6U CompactPCIProduct Guide g

This month’s issue includes a 6U CompactPCI Product Guide, and I’d like to take the opportunity to reflect a bit on the success and evolution of that technology.

Back in the 1994 time frame when CompactPCI was first being devel-oped, it began as 3U-only technology. It used the same Eurocardmechanics that were popularized by VME and an IEC standardized, high-

density, high-speed connector available from a number of vendors suitablefor 33 MHz PCI signaling. That connector was selected by the engineers atZiatech, with help from Mike Munroe, then at ERNI. The majority of VMEdesigns were 6U, and based on this, I was among a number of folks thatargued for adding the 6U CompactPCI form factor.

The 6U form factor presented some challenges and opportunities. Onechallenge was that the insertion and extraction forces were quite high when the entire rear of the card was populated with connectors. Fortunately, the IEEE standards for Eurocards evolved, and injector/ejector handles that pro-vided leverage became available. Eike Waltz, then at Rittal, was instrumental in bringing that to the table. Two of the opportunities that came along withthe extra connectors were a clean way to add secondary buses like the H.110 telephony bus to the backplane and the ability to route I/O out the rear through rear transition modules. PICMG has developed quite a number of subsidiary specifications defining the interoperable use of the extra backplane pins made possible with the 6U form factor. Both of these features have played a major part in CompactPCI’s success. The next major evolution of 6U CompactPCI came with the PICMG 2.16 Packet Switched Backplane standard, which was originally conceived by John Peters and his team at Performance Technologies. PICMG 2.16 interconnected a shelf full of CompactPCI single board computers via redundant Ethernet switches, also in the 6U CompactPCI form factor. This dramatically increased usable backplane bandwidth and provided redundancy. PICMG 2.16 paved the way for AdvancedTCA and was the industry’s first open standard for the switched serial interconnect standards we see popping up in many places.

By Joe Pavlat

Looking back and ahead at6U CompactPCI

Page 2: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

Recent 6U CompactPCI related products are listed here. For more information,enter the product’s RSC No. at www.compactpci-systems.com/rsc.

cPCI-6910Dual-core Intel Xeon Processor LV/ULV Universal blade • Supports Single Dual-Core Intel Xeon LV or ULV processors• Front Side Bus 667 MHz • Up to 2 GB DDR2 400 MHz soldered SDRAM with ECC • Four PCI Express GbE• Up to 4 USB 2.0 ports • PICMG 2.0, 2.1, 2.9, 2.16 compliant

RSC No. 35013

ADLINK Technologywww.adlinktech.com

CPCIStor Module6U CompactPCI storage blade • Onboard ATA controller supports CD/DVD, HDD, and solid-state flash• Supports Hot Swap Removal (ask about RAID support) • ATA disks available in Enhanced Dutycycle versions for NEBS Level 3 - 7/24 requirements • Operating Systems supported: VxWorks,Linux, and Windows

RSC No. 34800

ACT/Technicowww.acttechnico.com

Prosody X cPCI E1T1An E1/T1 digital network access card • Suits telco developers and systems integrators • Uses Aculab’s worldwide protocol coverage, including Aculab’s SS7 stack, available under a cost free license • Available with 8 or 16 E1/T1 trunks and software selectable E1/T1 interfaces • Flexible mix of protocols, including ISDN, CAS, and SS7 (ITU-T, China, and ANSI) • A variety of interconnect, switching and protocol conversion solutions can be readily crafted • High availability, reliability and scalability, with industry standard hardware, and software interoperability • Up to 128 SS7 signaling links • Non-circuit related (TCAP), messagingintensive applications such as prepaid and SMS

RSC No. 35408

Aculabwww.aculab.com

Adexp8021Intel Core Duo L2400 (1.66 GHz) w/ E7520 server chipset • Dual channel PC2-3200 Registered RAM, SEC/DED, or x4 SDDC • Two GbE, two Serial ATA, four USB 2.0 • Onboard SXGA graphics, 1280 x 24-bit• 6U CompactPCI Bus, PICMG EXP.0 R1.0 Specification • RoHS compliant, 0 °C to +55 °C operating range

RSC No. 32837

Advanet Inc.www.advanet.co.jp/en

TC84012 channel single-stop Time-to-Digital Converter (TDC) with single-start and multi-start acquisition modes • 50 ps timing resolution • Wide range with upto 20 s between first and last events • Large internal memory buffer, with up to 512 hits per channel • Low jitter (<3 ps rms) high stability (±2 ppm) internalclock source • External 10 MHz reference input • FPGA based Data Processing Unit (DPU) • Fast readout, with DMA mode for increased data throughput• Overvoltage-protected inputs, with 50 Ω K-Lock (LEMO) connectors • Built-in self calibration • Modular, single-slot 6U PXI/CompactPCI standard• Low power consumption (<22 W)

RSC No. 33445

Agilent-Acqiriswww.acqiris.com

Page 3: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

MIC-30428-slot 6U CompactPCI backplane • AC or DC CompactPCI 500 W + 250 W redundant(2+1) power supplies • PICMG 2.16 (CompactPCI Packet Switching Backplane) compliance• PICMG 2.5 (CompactPCI Computer Telephony) compliance • Built-in alarmmodule (MIC-3924L-AE)

RSC No. 32851

MIC-30436-slot 6U CompactPCI backplane • Supports two hot-swappable SCSI/SATA or removableIDE HDD bays • Built-in IDE slim-type DVD-ROM • AC or DC CompactPCI 250 W + 250 Wredundant (1+1) power supplies • Supports hot-swappable fan modules • PICMG 2.5 (CompactPCI Computer Telephony) compliance • Built-in alarm module (MIC-3924L-AE)

RSC No. 32850

Advantech Corporationwww.advantech.com

Dual-Core Xeon CompactPCI SBCModel PP 421/23x • Dual CPU 6U CompactPCI SBC supporting two dual-core Xeon CPUs • Up to 8 GB DDR2 ECC SDRAM in a single system or peripheralslot • Dual processor SBC in a single 6U CompactPCI slot • Supports two 1.66 GHz Dual-Core Intel Xeon ULV processors using Intel E7520 server chipset• Up to 8 GB dual-channel DDR2-400 ECC SDRAM in a single slot • PMC/XMC site support 66 MHz PCI-X and x8 PCI Express • Front and rear I/O • 33/66 MHz CompactPCI operation in system or peripheral slot • Can operate as a blade • Four GbE ports with option for PICMG 2.16

RSC No. 34761

6U CompactPCI Core 2 Duo SBCModel PP 412/03x • 6U CompactPCI Core 2 Duo SBC supporting two PMC sites, includingone XMC site • Up to 4 GB DDR2 ECC SDRAM • All in a single system or peripheral slot • TwoPMC sites supporting up to 100 MHz PCI-X • One XMC x8 PCI Express • Front and rear I/O• Supports 2.16 GHz or 1.5 GHz Intel Core 2 Duo processors • Intel E7520 server chipset• Up to 4 GB dual-channel DDR2-400 ECC SDRAM in a single slot • 33/66 MHz CompactPCI operation in system or peripheral slot • Can operate as a blade

RSC No. 34763

PP 302/02xTwo processor versions available • 1.8 GHz Intel Pentium M processor 745 uses mFC-PGA 478 (micro Flip-Chip Pin Grid Array) package • 1.4 GHz Intel Pentium M processor Low Voltage 738uses mFC-BGA 479 (micro Flip-Chip Ball Grid Array) package • 64 KB primary (L1) on-die cache2 MB of secondary (L2) on-die cache • 400 MHz Front Side Bus (FSB) • No CPU fan • 1.6 GHz processor version (1 MB L2 cache) available; see PP 300/02x datasheet • Utilizes 64-bitIntel 855GME chipset • Supports 400 MHz bus frequency • Uses Intel 6300ESB I/O Controller Hub

RSC No. 32659

Concurrent Technologies, Inc.www.gocct.com

Page 4: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

cCIBPMC6U-ETA 6U bridged dual PMC carrier that bridges extended temperature CompactPCI boards and PMCs • Features a rugged CompactPCI form factor, providing increased flexibility to military communications systems designers • Provides additional design choices to users through its differing bus speeds, maximizing the numberof PMCs that can be used: CompactPCI andPMC buses can both run at 66 or 33 MHz• Operating temperature range of -40 °C to+85 °C • Signal conditioning • DMA support• Low-power design: +5 V, +3.3 V, +12 V, -12 V • User-selectable VIO of 3.3 V or 5 V to the PMC

RSC No. 32891

Dynamic Engineeringwww.dyneng.com

cPCI4IP-MMMinimized PCI address footprint IndustryPack carrier for CompactPCI applications • 6U 4HP4 IP positions 8/32 clock selection for each slot, fused filtered power, I/O options • ID, INT, I/O, and Mem spaces are decoded for each IP slot• Single and double wide IP’s • 16- and 32- bit IPs • 32-bit access to 16-bit IPs • Full or mini-mized Memory Space decoding for 1/8 the PCI address requirement • With the cPCI4IP-MM option, 8 CompactPCI 4IP cards take the same PCI address space as 1 full Mem Space card

RSC No. 34905

ACQ132CPCI32 channel MHz class simultaneous sampling intelligent digitizer • 32 simultaneous analoginput channels, 2-32 MSps/channel, 14-bit resolution • Differential inputs • Intelligent cardwith 1 gigabyte memory and GbE on board • Large, distributed FPGA resource on board• Range of DSP functions including FIR filtering and Digital Downconverter

RSC No. 35482

D-TACQ Solutions Ltd.www.d-tacq.co.uk

Page 5: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

CR11Based on the Intel Core Duo Processor, the platform is designed to support processor speeds from 1.06 GHz up to 2.0 GHz • Intel Core 2 Duo runs at 1.5 GHz up to 2.0 GHz • Conduction cooled • Two PMC slots • PCI Express • 2x GbE

RSC No. 33156

ICS-72532-channel 6U CompactPCI DAC board • 6U CompactPCI data acquisition card • 32 differential output channels • 16 or 24-bit sample size • 288 kHz/ch. data rate • Simultaneous sampling across all channels on single or multiple boards • 32 separate delta-sigma DACs • 64-bit, 66 MHz CompactPCI PICMG 2.0 Rev.3.0 hot-swappable • FPDP II 400 MBps interface

RSC No. 33576

ICS-71032-channel 6U CompactPCI ADC board • 6U CompactPCI data acquisition card • 32 differential input channels • 216 KHz/ch. 24-bit resolution • Software selectable full scale input • FPDP II 400 MBpsinterface • 64-bit, 66 MHz CompactPCI PICMG 2.0, Rev. 3.0 hot swappable • 32 synchronous boards for simultaneous sampling • Sonar, acoustics, and test and measurement applications

RSC No. 33578

Tsumani 6U CPCI Development KitFPGA processor solution targeted at high performance software defined radio applications • Dual Stratix EP1S80 FPGAs are tightly coupled to provide apower platform for signal processing • Two PMC module sites provide I/O connectivity to either front panel or back panel connections • A direct highbandwidth 1 GBps path from the PMC P4 connector directly to the FPGAs • Model 919 Dual DAC Mezzanine provides broadband analog signal generationin a compact form • The board features two independent DAC channels each with its own 12-bit LVDS input capable of running at rates up to 160 MHz

RSC No. 32026

CP11Rugged 6U SBC • Up to 4 GB of DDR2 SDRAM (200 MHz) with enhanced ECC, four independent onboard PCI buses, system host and peripheral modesupport for the CompactPCI backplane, two PMC interfaces (64-bit/133 MHz and 32-bit/33 MHz) • Instead of the PMC1, a PCI Express based XMC interface is available on request • Two GbE, one Fast Ethernet, two serial interfaces (RS-232 or RS-422/485), USB 2.0, integrated HDD, or flash drive • High performance 2D/3D ATI video controller capable of driving two displays in parallel supports VGA/DVI interface • Intel Core 2 Duo at 2.16 GHz, Intel Core Duo at 2.0 GHz2x PMC expansion site • One XMC optional • Up to 4 GB DDR2 SDRAM w/ECC 2x GbE

RSC No. 33447

GE Fanuc Intelligent Platforms, Inc.www.gefanucembedded.com

Single Board ComputersGD Canada designs and manufactures conduction-cooled Single Board Computers (SBCs)using Intel processors • 6U and 3U form factors for CompactPCI backplanes • Fully backward compatible with earlier models • Upgradeable via the change-out of processor, memory, andI/O modules • Used within GD Canada computer systems and sold as individual products

RSC No. 35281

General Dynamicswww.gdcanada.com

Page 6: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

cPCI6U-24DSI32R32-channel 24-bit delta-sigma CompactPCI 6U analog input board with rear I/O • Low noise, 24-bit resolution, low phase distortion, andmulti-board synchronization • Suits state-of-the-art sonar and noise monitoring applications • 32-channel cPCI6U-24DSI32 analog input boardprovides a high-density 24-bit analog input resources on a standard 6U CompactPCI expansion board • Applications from precision voltagemeasurements to complex audio signal and waveform analysis

RSC No. 34985

General Standards Corporationwww.generalstandards.com

Duet 3U 64-bit 1 GHz TMS320C6416 DSP (x2), 64 MB SDRAM per processor • Flexible internal/externalcommunication mesh • 64-bit/66 MHz CompactPCI • PMC/XMC site with Jn4 to FPGA and4 RocketIO per VITA 42 • External data port, up to 12 Gbps • 4M or 5M Virtex-II Pro FPGA• Up to two 2 MB private DDR SBSRAM • Up to two 128 MB private DDR SDRAM, dedicated800 MBps links between DSPs • 3U CompactPCI with PXI support • Suits high-end co-processing, wireless, broadband communications, RADAR, video, and biometrics

RSC No. 32856

QuadiaQuad-DSP • Dual FPGA • Dual PMC sites • Inter-processor connectivity and access to external interfaces • Four C6416 DSPs split in two independent clusters each hosting a PMC site • One large FPGA for end-user code • Central FPGA routing interprocessor communication • End-user FPGA communication • External port serial I/O for PCIe or other private link • Global memoryand PCI interface • 1 GHz TMS320C6416 DSP (x4) • 64 MB SDRAM per processor • Flexible internal/external communication mesh • 64-bit/66 MHz CompactPCI • Two PMC sites with Jn4 to FPGA • External data port, up to 12 Gbps • Two 4M Gate FPGA reserved for end-user code • Up to two 2 MB private DDR SBSRAM • Up to two 128 MB private DDR SDRAM • Up to 512 MB Global DDR SDRAM • Suits high-end co-processing, wireless, and broadband communications

RSC No. 34737

Quixote 64-bit 6UAdvanced signal capture, generation, and co-processing • 1 GHz TMS320C6416 DSP and2 to 6 MGATE Virtex-II FPGA • 32 MB SDRAM, 8 MB ZBT SBSRAM, and AD6645 and AD9764 converters • 64/32 bit CompactPCI, 66 MHz, 5 V/3.3 V and complex trigger modes with HW event logging • PMC site with Jn4 to FPGA DIO and PICMG 2.17 StarFabric compliant • Suits Software Defined Radio, wireless IP and RADAR, development and hardware testing • Physical Layer field testing, ultra-fast flexible data acquisition, vector signal generation, and electronic warfare

RSC No. 32861

Innovative Integrationwww.innovative-dsp.com

IC-e6-cPCIbHigh performance 6U CompactPCI board • Powered by one or two of Freescale’s mostadvanced 1.4 GHz MPC7448 PowerPC processors • PICMG 2.16 compliant • Marvell Discovery III chipset (MV64460) • Low power consumption • Standard, extended, and rugged grades

RSC No. 32982

Interface Conceptwww.interfaceconcept.com

Page 7: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

CP213Single-width, 6U, CompactPCI/PXI module with either 32 or 64 differential analog input channels• 32, 64, or 128 channels of analog input • 16 multifunction digital I/O (TTL) channels that may beconfigured as digital in, digital out, or selectively attached to 2 frequency in, 2 counter in, and/or 2 timerout channels • 16-bit resolution • Programmable gain per channel; programmable scan rates of <1 S/s through 100 KS/s • Precision onboard reference for end-to-end calibration

RSC No. 34804

KineticSystems Company, LLCwww.kscorp.com

CP6001Energy efficient embedded Intel dual core processors • 1.2 GHz Intel Core Duo U2500 ULV processor • Intel Core 2 Duo L7400 LV processor • Based on the Intel Mobile 945GM chipset with a front side bus of up to 667 MHz and ICH7-R Southbridge • Two independent digital video outputs to the rear I/O (2x DVI - 1x DVI and 1x HDMI) • AC97 audio capabilities • 3 x GbE • 4 x SATA with RAID 0/1/5/10 functionality • 6 x USB 2.0, 2 x COM and VGA or DVI • Can also accommodate a PMC slot or an onboard 2.5 inch SATA HDD • Up to 8 GB of USB or 2 GB soldered flash • Supports Linux, Windows XP, XP embedded, and VxWorks 6

RSC No. 34182

CP6923 GbE Switch6U CompactPCI GbE Switch, PICMG 2.16 compliant • Leading edge technology basedon BCM5650X chip • 24x GbE ports • Non-blocking Layer 2 and 3 switching and routing• Copper, optical, rear I/O version • Hot swap, IPMI • Fully managed • Comprehensive firmware package • Applies to VoIP installations such as call servers, media gateways,and trunking gateways in wireline and wireless networks, as well as VoIP systems inenterprise networks with high demands on performance

RSC No. 32256

Kontronwww.kontron.com

TMS320C6701 Virtex-IITexas Instruments’ C6701 DSP • Xilinx Virtex-II series FPGA, up to XC2V8000 • Multiple I/O interfaces: Onboard CODEC, VIM expansion sites, 60-pin GPIO header and JTAG • Hardware drivers integration in Simulink/Xilinx System Generator Blocksets for quick implementation of Simulink models • DSP and FPGA-in-the-loop, cosimulation of Simulink/Xilinx System Generator models • Leading edge communication interface allowing real-time datamonitoring from Simulink scopes and remote operations

RSC No. 32028

VHS-DACHigh performance multichannel D/A for phased array antenna systems, radar/sonar, communications receivers,up-sampling to IF stage, and RF/IF AGC apps • Eight 125 MSPS output channels • Optional add-on daughter boardprovides 8 additional output channels or 8 additional input channels • 32-bit 25 MHz • FPDP interface with 400 MBps transfer rate (25 MSPS per channel at 8 channels; 12.5 MSPS at 16 channels) • Low level hardware drivers API andGUI • High level hardware drivers integration in Simulink Blocksets • Leading edge communication interface fordata recording and playback to/from the onboard SDRAM

RSC No. 32029

Lyrtechwww.lyrtech.com

Page 8: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

SM QUAD VIRTEX-4Xilinx hybrid architecture – high-performance logic • Four TI TMS320C6416 DSPs for processing power• Dual LYRIO+ very-high-speed expansion sites can connect to Lyrtech add-on I/O expansion modulesyielding: minimum sustained, full-duplex raw data exchanges of 12 Gbps 128 MB external SDRAM per DSPand FPGA • Six 8-Gbps RapidCHANNEL links for full-duplex communications between FPGAs and externalI/O interfaces • 6U, CompactPCI form factor • Stackable, to build seamless DSP–FPGA for very large-scaleprocessing farms • Supports model-based design flow for the most powerful integrated developmentenvironments on the market

RSC No. 33923

Lyrtechwww.lyrtech.com

D7 Server BladeSBC equipped with one or two Intel Xeon dual core processors, providing up to four CPUcores with a frequency of 1.66 GHz, and the Intel E7520 server chipset • Intel dual coreXeon 1.66 GHz • 2 or 4 CPU cores on board • 4/8HP CompactPCI system or peripheral slot • PCI 64-bit/66 MHz or PCI-X 64-bit/133 MHz • Hot swap, PICMG 2.16 support • Up to 4 GB DDR2 ECC SDRAM • Nonvolatile SRAM, FRAM • Up to 1 GB flash-on-disk (NAND), hard disk• 2 SATA, 2 PATA interfaces • Graphics up to 1280 x 1024 • 4 GbE (PCIe)

RSC No. 33290

MEN Micro Elektronik GmbHwww.menmicro.com

CCR-100 SBCSingle-slot Pentium M SBC • 1.1, 1.4, 1.6, 1.8, or 2.0 GHz • Intel 855GME memory controller, which supports a 400 MHz processor bus and single-channel unbuffered DDR333 SDRAM with ECC • An Intel 6300ESB I/O controller hub handles the extensive I/O capability • GbE via PICMG 2.16 • Intel 855GMEmemory controller hub with built-in 3D graphics engine • Hot swappable

RSC No. 32022

CCR-200 SBCSingle-slot 6U PICMG 2.16 SBC • 4-Ch A/D, 1-Ch D/A w/Virtex-4 FPGAs 6U CompactPCI• Complete software radio interface solution • Eight 125 MHz 14-bit A/Ds • Two digitalupconverters • Two 500 MHz 16-bit D/A • 1536 MB of DDR2 SDRAM • Xilinx Virtex-4FPGAs • Up to 2.0 seconds of delay or data capture at 125 MHz • Dual timing buses forindependent input and output clock rates • LVDS clock/sync bus for multi-modulesynchronization • Custom FPGA I/O through CompactPCI J3 and J5 connectors

RSC No. 32023

Momentum Series CLA-100Single-slot SBC • UltraSPARC IIi+ processor • Hot swappable • Power-on self-test (POST)• Open Boot firmware • Solaris operating environment

RSC No. 32467

Mercury Computer Systems, Inc.www.mc.com

Page 9: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

CompactPCI and AdvancedTCA Systems February 2008 39

Product Guide6U CompactPCI

Momentum Series CX6-200Single board computer • Two Dual-Core Intel Xeon processors ULV at 1.66 GHz • 4-way SMP • Three PCI Expressx8 links with 2 GBps bandwidth each • Numerous I/O interfaces • 667 MHz front side bus • Dual DDR2-400 memory interfaces to access up to 4 GB of memory • Intel E7520 Memory Controller Hub • Intel 6300ESB I/O Controller Hub• Serial, USB, and mass storage interfaces • SVGA video with onboard ATI Rage Mobility M graphics chip

RSC No. 31520

Mercury Computer Systems, Inc.www.mc.com

78C2 6U CompactPCI Multifunction CardSingle-slot, 6-module multifunction card • Universal card eliminates the complexity andsize constraints of using multiple, independent, single-function cards • Extends the capabilityof the earlier 78C1 • Can include the functions of Synchro/Resolver Measurement (4-channels), LVDT Measurement (4-channels), A/D(10-channels), D/A (10-channels), Function Generator (4-channels), Discrete I/O(16-channels), TTL I/O (16-channels), Transceiver I/O (11-channels), and RTD (6-channels) • Incorporates an Ethernet interface that can be used to transfer data to and from the boardwithout using the backplane bus

RSC No. 33382

North Atlantic Industrieswww.naii.com

Pentium M CPUPentium M 2.0 GHz, 1.8 GHz, or 1.6 GHzsystem/peripheral CPU board, up to 2 GB DRAM, 4HP 6U • Intel E7501 chipset • PICMG 2.16 Packet Switching Backplane support • Optional PICMG 2.9 (IPMI) and PICMG 2.1 (Hot Swap) support • Ability to turn off the CompactPCI bus • Optional plug-in CompactFlash or Microdrive storage • Dual Gigabit Ethernet • Supports up to 2 GB of DDR200/266 plug-in memory modules

RSC No. 32654

One Stop Systems Inc.www.onestopsystems.com

Page 10: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

Pentium III CPUPentium III 1.0 GHz System CPU board • 6U • Part number: OSS-613-1 • SDRAM memory up to 1 GB • Dual 10/100BASE-T Ethernet • 4 MB SVGA video • Single-slot 4HP form factor • Supports CompactFlash

RSC No. 32655

One Stop Systems Inc.www.onestopsystems.com

CPC7510PowerPC 6U Single Board Computer • IBM750FX or IBM750GX • CompactPCI host or peripheral controller • Marvell Discovery II System Controller • Two 64-bit 66 MHz PMC slots • Two10/100 Ethernet ports • Hot swap/high availability

RSC No. 33014

CPC7520PowerPC 6U Single Board Computer • IBM750FX or IBM750GX up to 1 GHz • CompactPCIhost or peripheral controller • Marvell Discovery III System Controller • Two 64-bit 66 MHzPCI-X PMC slots • Hot swap/high availability • Two Front-Panel GbE (10/100/1000) • TwoPCI-X 66 MHz/64-bit PMC slots (PrPMC) • Standard CompactFlash socket • Onboard flash

RSC No. 33015

Orion Technologies Inc.www.otisolutions.com

7142 Multichannel Transceiver Multichannel transceiver PMC/XMC module with FPGA • VITA 42.0 XMC compatible with switched fabric interfaces • Four 125 MHz 14-bit A/Ds• Optional factory installed IP Core DDC • One digital upconverter with500 MHz 16-bit D/A • 768 MB of DDR SDRAM • Dual timingbuses for independent input and output clock rates• LVDS clock/sync bus for multipleboard synchronization • 32 pairsof LVDS connections to the Virtex-IIPro FPGA for custom I/O on P4• Ruggedized and conduction-cooled versions available• Also available in 3U CompactPCI (Model 7342),6U CompactPCI (Models 7242and 7242D), andPCI (Model 7642)

RSC No. 32556

Pentek, Inc.www.pentek.com

Page 11: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

7342 / 7242DMultichannel Software Radio Transceiver with Virtex-4 FPGAs - 3U/6U CompactPCI • Completesoftware radio interface solution• Four or eight 125 MHz 14-bit A/Ds• One or two digital upconverters• One or two 500 MHz D/As• 768 or 1536 MB of DDR2 SDRAM • Two or four Xilinx Virtex-4 FPGAs • Dual timing buses for independent input and output clock rates • LVDS clock/sync bus for multiboardsynchronization • Custom FPGA I/O• Factory-installed downconverterIP cores available

RSC No. 34440

Pentek, Inc.www.pentek.com

PI-2005Digital pattern generator for serial or parallel data streams• Generate clocks, addresses, data, or triggers for semiconductor test and characterization and system integration • 225 MHz bitrate (NRZ) with precision master clock synthesis, external clock input, external start/stop inputs, and I2C • 16-64 channels in 16-channel increments, with TTL, LVTTL, or 5 V CMOS outputlevels • (PI-PAT) with simple instruction • Fast pattern generation with nearly limitless looping depth • Optional programmabledelay per channel • Local or remote (GPIB) control• ASCII command set • Complete instrument or as6U CompactPCI cards

RSC No. 32191

Pulse Instrumentswww.pulseinstruments.com

Page 12: Looking back and ahead at 6U CompactPCI Tpdf.cloud.opensystemsmedia.com/advancedtca-systems.com/Prod… · Prosody X cPCI E1T1 An E1/T1 digital network access card • Suits telco

Product Guide6U CompactPCI

cPCI-CAN4 CAN bus channels for 6U CompactPCI systems, featuring Philips’ SJA1000 widely used CAN controller on each channel • Each CAN interface hasa MC68332 microcontroller, providing powerful and safe communication on CAN networks • Host CPU relieved from the stack protocol burden• Up to 4 intelligent CAN channels • 3.3 V and 5 V PCI interface

RSC No. 34464

Saelig Co., Inc.www.saelig.com

cPENTXM2Blade SBC • Intel 1.67 GHz dual core Xeon with 667 MHz FSB and E7520 server-classmemory controller hub • Can be equipped with up to 4 GB ECC DDR2-400 SDRAM • DualGbE ports routed to the backplane compliant with PICMG 2.16/VITA 31 (switched Ethernet)• Supports PICMG 2.9/VITA 38 IPMI management software • Two additional GbE ports, plustwo USB 2.0 ports, can be routed to the front panel • Serial ATA, SXGA graphics, two serialports, PS/2, and a PMC mezzanine connector

RSC No. 32712

Thales Computerswww.thalescomputers.com

2000-6U-EXTM-LFCompactPCI 6U extender card • Designed for both hardware development andtest/measurement applications • Test points for signals • Power and ground planes• Fuses protect voltages • RoHS compliant

RSC No. 34765

Twin Industries, Inc.www.twinhunter.com

VRM-CD3 / VRM-CRBIntel i915 (Sonoma) chipset • Dual 200-pin SODIMM socket, DDR2 533 SDRAM, 2 x 1 GB max., symmetric dual channel capable • Ethernet I/O: Triple 10/100/1000Mbps GbE controller, 1 port software switchable (BIOS) between front panel and rear I/O access • Proprietary Expansion Interface: Onboard LPC/USB/AC97 Super I/O, USB and audio interface connector, suitablemezzanine companion boards • Quad channel Serial ATA interface • ICH6 integrated 32-bitPCI bridge, 133 MBps CompactPCI master • Phoenix BIOS • Drivers: Intel Graphics andnetworking • Typical power requirements: +3.3 V at 0.17 V/-0.1 V +5 V at 0.25 V/-0.15 V• Operating temperature: 0 °C to +60 °C • Storage temperature: -40 °C to +85 °C

RSC No. 32719

V Rose Microsystems, Inc.www.vrosemicrosystems.com

XCPC-9100 CompactPCI Carrier BoardMezzanine carrier board • Sites for two PMC modules • PMC sites support PrPMC modes• 64-bit, 33/66 MHz, up to 512 MBps operation • Two 10/100/1000Mbps Ethernet portson the front panel using RJ-45s • Onboard 8-port 10/100/1000Mbps Ethernet switch• Rear Ethernet ports from PMC modules is routed to on-board switch and provides PICMG 2.16• Full hot swap PICMG 2.1 compliant • Onboard IPMI controller • Status LEDs for Power andHot Swap • PLX Technology PCI-X to PCI-X bridge • Supports standard (IEEE1386.1) PMC modules • PICMG 2.0, version 3.0 compliant • Front or back panel I/O supports on both PMC sites• 128 I/O lines with 16 differential pairs via rear panel J3, J5 CompactPCI connectors• 3.3 V or 5 V PCI signaling for the PMC sites

RSC No. 33477

Xembedded, Inc.www.Xembedded.com