Loctite 277

MATERIAL SAFETY DATA SHEET

Revision: 11.10.2011Page 1 of 5 Loctite 277 Threadlocker High Strength

SECTION 1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

Product name: Loctite 277 Threadlocker High Strength

Product-Code: 232658

Part Number(s): 27770, 27750

Intended use: Threadlocker

Supplier:HENKEL AUSTRALIA PTY. LIMITEDADHESIVE TECHNOLOGIES135-141 Canterbury Road3137 Kilsyth, Victoria

Australia

Phone: +61 (3) 9724 6444

Emergency information: 24 HOUR EMERGENCY CONTACT NUMBER 03 9724 6556

SECTION 2. HAZARDS IDENTIFICATION

STATEMENT OF HAZARDOUS NATURE:Hazardous according to the criteria of ASCC.

Classification of material Xi - Irritant

Risk phrases:R36/37 Irritating to eyes and respiratory system.

Safety phrases:S25 Avoid contact with eyes.S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.S46 If swallowed, seek medical advice immediately and show this container or label.S51 Use only in well-ventilated areas.S23 Do not breathe vapour.

Dangerous Goods information:Not classified as Dangerous Goods according to the criteria of the Australian Code for the Transport of Dangerous Goods byRoad and Rail (ADG Code).

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Identity of ingredients:

Chemical ingredients CAS-No. ProportionCumene hydroperoxide 80-15-9 > 1 - < 3 %

N,N-dimethyl-o-toluidine 609-72-3 > 0.1 - < 0.5 %non hazardous ingredients~ > 60 %



SECTION 4. FIRST AID MEASURES

Ingestion: Rinse mouth, do not induce vomiting, consult a doctor.

Skin: Rinse with running water and soap.Seek medical advice.

Eyes: Rinse immediately with plenty of running water (for 10 minutes). Seek medical attention ifnecessary.

Inhalation: Move to fresh air. If symptoms persist, seek medical advice.

Medical attention and specialtreatment:

Treat symptomatically.

First Aid facilities: Eye washNormal washroom facilities

SECTION 5. FIRE FIGHTING MEASURES

Suitable extinguishing media: If product is involved in fire extinguish with dry powder, foam or carbon dioxide.

Decomposition products in case offire:

Oxides of carbon.Oxides of sulfur.Oxides of nitrogen.Irritating organic vapours.

Particular danger in case of fire: None

Special protective equipment forfire-fighters:

Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear.

SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions andemergency procedures:

Avoid skin and eye contact.

Ensure adequate ventilation.

Environmental precautions: Do not let product enter drains.

Clean-up methods: For small spills wipe up with paper towel and place in container for disposal.For large spills absorb onto inert absorbent material and place in sealed container fordisposal.

SECTION 7. HANDLING AND STORAGE

Precautions for safe handling: Use only in well-ventilated areas.Avoid skin and eye contact.



Conditions for safe storage: Ensure good ventilation/extraction.Store in original containers at 8-21C (46.4-69.8F) and do not return residual materials tocontainers as contamination may reduce the shelf life of the bulk product.Store in a cool, well-ventilated place.Do not expose to direct heat.Store in sealed original container.

SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION

National exposure standards:

None

Engineering controls: Ensure good ventilation/suction at the workplace.

Eye protection: Wear protective glasses.

Skin protection: Wear suitable protective clothing.The use of chemical resistant gloves such as Nitrile are recommended.

Please note that in practice the working life of chemical resistant gloves may beconsiderably reduced as a result of many influencing factors (e.g. temperature). Suitablerisk assessment should be carried out by the end user. If signs of wear and tear are noticedthen the gloves should be replaced.

The use of chemical resistant gloves such as Neoprene or Natural Rubber arerecommended

Respiratory protection: Use only in well-ventilated areas.If inhalation risk exists, wear a respirator or air supplied mask complying with therequirements of AS/NZS 1715 and AS/NZS 1716.

SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance: redOdor: characteristicSpecific gravity: 1.1Flash point: > 93.3 C (> 199.94 F)Density: 1.0800 g/cm3Solubility: Solvent: Water, Slight

SECTION 10. STABILITY AND REACTIVITY

Conditions to avoid: Keep away from heat, spark and flame.



Incompatible materials: Strong acids and oxidizing agents.copperRust.Iron.Oxygen scavengers.Strong alkalis.Reducing agents.Other polymerization initiators.

Hazardous decompositionproducts:

Oxides of carbon.

Irritating vapors.

Hazardous polymerization: Will not occur.

SECTION 11. TOXICOLOGICAL INFORMATION

HEALTH EFFECTS:Ingestion: May be harmful if swallowed.

Skin: May cause mild skin irritation.

Eyes: This product is irritating to the eyes.

Inhalation: May cause respiratory tract irritation.

Aggravated medical condition: Eye, skin, and respiratory disorders.

Toxicity data:Acute oral toxicity: Cumene hydroperoxide

80-15-9LD L0 (Mouse) = 5,000 mg/kg

SECTION 12. ECOLOGICAL INFORMATION

General ecological information: Do not empty into drains, soil or bodies of water.

SECTION 13. DISPOSAL CONSIDERATIONS

Waste disposal of product: Dispose of in accordance with local and national regulations.

Disposal for uncleaned package: After use, tubes, cartons and bottles containing residual product should be disposed of aschemically contaminated waste in an authorised legal land fill site or incinerated.

SECTION 14. TRANSPORT INFORMATION

Road and Rail Transport:

Dangerous Goods information: Not classified as Dangerous Goods according to the criteria of theAustralian Code for the Transport of Dangerous Goods by Road andRail (ADG Code).

General information:Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR.



SECTION 15. REGULATORY INFORMATION

SUSDP Poisons Schedule: None

AICS: All components are listed or are exempt from listing on the Australian Inventory ofChemical Substances (AICS).

SECTION 16. OTHER INFORMATION

Abbreviations/acronyms: ASCC - Australian Safety and Compensation CouncilSUSDP - Standard for the Uniform Scheduling of Drugs and Poisons

Reason of change: Reviewed MSDS. Reissued with new date. involved chapters: 1-16

Date of previous issue: 16.08.2007

Disclaimer:The percentage weight (% w/w) of ingredients is not to be taken as a specificationguaranteed by Henkel Australia Pty. Limited, but only as an approximate guide to thecontent of hazardous ingredients in the material. The information contained herein doesnot constitute a guarantee by Henkel Australia Pty. Limited concerning the properties ofthe material. The information contained in this Material Safety Data Sheet is offered ingood faith and has been developed from what is believed to be accurate and reliablesources. The information is offered without warranty, representation, inducement orlicence and Henkel Australia Pty. Limited assumes no legal responsibility for relianceupon same. Henkel Australia Pty. Limited disclaims any liability for loss, injury ordamage incurred in connection with the use of the material or its associated MaterialSafety Data Sheet. This information is not to be construed as a representation that thematerial is suitable for any particular purpose or use except those conditions andwarranties implied by either Commonwealth or State statutes. Customers are encouragedto make their own enquiries as to the material's characteristics and, where appropriate, toconduct their own tests in the specific context of the material's intended use.

Loctite 277

Documents

Transcript of Loctite 277