LM1895
-
Upload
chidiebere-kalu -
Category
Documents
-
view
7 -
download
0
description
Transcript of LM1895
-
5/21/2018 LM1895
1/8
TLH7919
LM1895LM
2895AudioPowerAmplifier
July 1987
LM1895LM2895 Audio Power Amplifier
General DescriptionThe LM1895 is a 6V audio power amplifier designed to de-liver 1W into 4X Utilizing a unique patented compensation
scheme the LM1895 is ideal for sensitive AM radio applica-tions This new circuit technique exhibits lower noise lowerdistortion and less AM radiation than conventional designs
The amplifiers supply range (3V9V) is ideal for battery op-eration The LM1895 is packaged in an 8-pin miniDIP for
minimum PC board space For higher supplies (VS l 9V)the LM2895 is available in an 11-lead single-in-line package
The 11-lead package has been redesigned resulting in aslightly degraded thermal characteristic shown in the figureDevice Dissipation vs Ambient Temperature
FeaturesY Guaranteed low crossover distortionY Low AM radiation
Y Low noiseY 3V 4X PO e 250 mWY Wide supply operation 3V 15V (LM2895)Y Low distortionY No turn on popY Smooth waveform clippingY 8-pin miniDIP (LM1895)Y 12V 4X PO e 4W (LM2895)Y Tested for low crossover distortion
ApplicationsY Compact AM-FM radiosY Battery operated tape player amplifiersY Line driver
Typical Applications
TLH79191
FIGURE 1 LM1895 with AV e 500 BW e 5 kHz AM Radio
Application (VIN e 42 mV for Full Power Output)
Order Number LM1895N or LM2895P
See NS Package Number N08E or P11A
C1995 National Semiconductor Corporation RRD-B30M115Printed in U S A
-
5/21/2018 LM1895
2/8
Absolute Maximum RatingsIf MilitaryAerospace specified devices are required
please contact the National Semiconductor Sales
OfficeDistributors for availability and specifications
Supply VoltageLM1895 VS e 12V
LM2895 VS e 18V
Operating Temperature (Note 1) 0C to a70C
Storage Temperature b65C to a150C
Junction Temperature 150C
Lead Temperat ure ( Sol dering 10 sec) 260C
Electrical CharacteristicsUnless otherwise specified TA e 25C AV e 200 (46 dB) For the LM1895 VS e 6V and RL e 4X For the LM2895 TTAB e
25C VS e12V and RL e 4X Test circuit shown in Figure 2
Parameter Conditions LM1895 LM2895
UnitsMi n Typ Max Min Typ Max
Supply Current PO e W 8 14 12 20 mA
Operating Supply Voltage 3 10 3 15 V
Output Power THD e 10% f e 1 kHz
LM1895N VS e 6V RL e 4X TA e 25C 09 11 W
VS e 9V RL e 8X( 11 WLM2895P VS e 12V RL e 4X TTAB e 25C
36 43 W
VS e 12V RL e 8X( 25 WDistortion f e 1 kHz
POe
50 mW 027 027 %PO e 05W 020 020 %
PO e 10W 015 %
f e 20 kHz PO e 100 mW VS e 36V 30 30 %
Crossover Distort ion f e 20 kHz RL e 4X PO e 100 mW 3 3 %VCC e 36V
Power Supply Rejection CBY e 100 mF f e 1 kHz CIN e 01 mF 40 52 40 52 dBRatio (PSRR) Output Referred VRIPPLE e 250 mV
Noise Equivalent Input Noise RS e 0
CIN e 01 mF BW e 20 b20 kHz 14 14 mV
CCIRARM 14 14 mV
Wideband 20 20 mV
DC Output Level 28 30 32 56 60 64 V
Input Impedance 50 150 350 50 150 350 kX
Input Offset Voltage 5 5 mV
Input Bias Current 120 120 nA
Note 1For operation at ambient temperature greater than 25 C the LM1895LM2895 must be derated based on a maximum junction temperature using a thermalresistance which depends upon mounting techniques
Typical Performance Characteristics
vs Ambient Temperature
LM2895 Device Dissipation
Temperature
Dissipation vs Ambient
LM1895 Maximum Device
Operation
Voltage Gain for Stable
b3 dB Bandwidth vs
TLH79192
2
-
5/21/2018 LM1895
3/8
Typical Performance Characteristics (Continued)
Speaker Lead Placement
vs Field Strength for Different
AM Recovered Audio and Noise
AV e 54 dB BW e 30 kHz
THD and Gain vs Frequency
AV e 54 dB BW e 5 kHz
THD and Gain vs Frequency
AV e 46 dB BW e 30 kHz
THD and Gain vs Frequency
AV e 40 dB BW e 20 kHz
THD and Gain vs Frequency
AV e 34 dB BW e 50 kHz
THD and Gain vs Frequency
Output) vs Frequency
Ratio (Referred to the
Power Supply Rejection
Voltage
Power Output vs Supply
vs Output Power
Total Harmonic Distortion
Output Power RL e 8X
Power Dissipation vs
Output Power RL e 4X
Power Dissipation vs
TLH79193
3
-
5/21/2018 LM1895
4/8
Equivalent Schematic
TLH79194
Pin 7 no connection on LM1895
Pins 4 7 10 11 no connection on LM2895
( ) indicates pin number for LM2895
Typical Applications (Continued)
TLH79195
FIGURE 2 Amplifier with AV e 200 BW e 30 kHz
4
-
5/21/2018 LM1895
5/8
External Components (Figure 2)Components Comments
1 R1 R5 Sets voltage gain AV e 1 a R1R5
2 R2 Bootstrap resistor sets drive current for output stage and allows pin 2 to go
above VS3 RO Works with COto stabilize output stage
4 C4 Input coupling capacitor Pin 4 is at a DC potential of VS2 Low frequencypole set by
fL e1
2q RINC45 C5 Feedback capacitor Ensure unity gain at DC Also a low frequency pole at
fL e1
2q R5C56 C2 Bootstrap capacitor used to increase drive to output stage A low frequency
pole is set by
fL e1
2q R2C27 C1 Compensation capacitor This stabilizes the amplifier and adjusts the
bandwidth See curve of bandwidth vs allowable gain
8 C3 Improves power supply rejection (See Typical Performance Curves)Increasing C3 increases turn-on delay
9 CC Output coupling capacitor Isolates pin 1 from the load Low frequency poleset by
fL e 12q CCRL
10 CO Works with ROto stabilize output stage
11 CS Provides power supply filtering
Connection Diagrams
Dual-In-Line Package
TLH79196
Top View
Single-In-Line Package
TLH79197
Top View
5
-
5/21/2018 LM1895
6/8
Application HintsAM Radios
The LM1895LM2895 have been designed to fill a widerange of audio power applications A common problem withIC audio power amplifiers has been poor signal-to-noise per-
formance when used in AM radio applications In a typicalradio application the loopstick antenna is in close proximity
to the audio amplifier Current flowing in the speaker andpower supply leads can cause electromagnetic coupling tothe loopstick resulting in system oscillation In addition
most audio power amplifiers are not optimized for lowestnoise because of compensation requirements If noise from
the audio amplifier radiates into the AM section the sensitiv-ity and signal-to-noise ratio will be degraded
The LM1895 exhibits extremely low wideband noise due in
part to an external capacitor C1 which is used to tailor thebandwidth The circuit shown inFigure 2 is capable of asignal-to-noise ratio in excess of 60 dB referred to 50 mW
Capacitor C1 not only limits the closed loop bandwidth italso provides overall loop compensation Neglecting C5 in
Figure 2 the gain is
TLH79198
FIGURE 3 Improved AM Sensitivity
Over Conventional Design
AV(S) eS a AV0o
S a 0o
where AV eR1 aR5
R5 0o e
1
R1C1
A curve of b3 dB BW (0o) vs AV is shown in the Typical
Performance CurvesFigure 3shows a plot of recovered audio as a function offield strength inmVM The receiver section in this example
is an LM3820 The power amplifier is located about twoinches from the loopstick antenna Speaker leads run paral-lel to the loopstick and are 18 inch from it Referenced to a
20 dB SN ratio the improvement in noise performanceover conventional designs is about 10 dB This corresponds
to an increase in usable sensitivity of about 85 dB
TLH79199
FIGURE 4 Printed Circuit Board Layout for LM1895
6
-
5/21/2018 LM1895
7/8
Physical Dimensions inches (millimeters)
Molded Dual-In-Line Package (N)
Order Number LM1895N
NS Package Number N08E
7
-
5/21/2018 LM1895
8/8
LM
1895LM2895AudioPow
erAmplifier
Physical Dimensions inches (millimeters) (Continued)
Molded Single-In-Line Package (P)
Order Number LM2895P
NS Package Number P11A
LIFE SUPPORT POLICY
NATIONALS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORTDEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION As used herein
1 Life support devices or systems are devices or 2 A critical component is any component of a life
systems which (a) are intended for surgical implant support device or system whose failure to perform caninto the body or (b) support or sustain life and whose be reasonably expected to cause the failure of the lifefailure to perform when properly used in accordance support device or system or to affect its safety or
with instructions for use provided in the labeling can effectivenessbe reasonably expected to result in a significant injury
to the user
National Semiconducto r National Semiconduct or Natio nal Semiconducto r National Semiconduct orCorporation Europe Hong Kong Ltd Japan Ltd1111 West Bardin Road Fax (a4 9) 0 -1 80 -5 30 8 5 8 6 1 3t h F lo or S tr ai gh t B lo ck T el 8 1- 04 3- 29 9- 23 09Arlington TX 76017 Email cnjwget ev m2 n sc c om O ce an C en tr e 5 C an to n R d F ax 8 1- 04 3- 29 9- 24 08Tel 1(800) 272-9959 Deutsch Tel (a49) 0-180-530 85 85 Tsimshatsui KowloonFax 1(800) 737-7018 Eng lish Tel (a49 ) 0- 180 -53 2 7 8 32 Ho ng K ong
Franais Tel (a4 9) 0 -1 80 -5 32 9 3 5 8 T el ( 85 2) 2 73 7- 16 00Italiano Tel (a4 9) 0 -1 80 -5 34 1 6 8 0 F ax ( 85 2) 2 73 6- 99 60
National doesnot assumeany responsibilityfor useof anycircuitry described nocircuit patent licenses areimplied and National reserves the right at anytime without noticeto changesaid circuitryand specifications