Links Between Machining Parameters and Surface Integrity in

11
HAL Id: hal-00800060 https://hal.archives-ouvertes.fr/hal-00800060 Submitted on 13 Mar 2013 HAL is a multi-disciplinary open access archive for the deposit and dissemination of sci- entific research documents, whether they are pub- lished or not. The documents may come from teaching and research institutions in France or abroad, or from public or private research centers. L’archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d’enseignement et de recherche français ou étrangers, des laboratoires publics ou privés. Links Between Machining Parameters and Surface Integrity in Drilling Ni-Superalloy Vincent Dutilh, Gilles Dessein, Joël Alexis, Géraldine Perrin To cite this version: Vincent Dutilh, Gilles Dessein, Joël Alexis, Géraldine Perrin. Links Between Machining Parameters and Surface Integrity in Drilling Ni-Superalloy. Advanced Materials Research, Trans Tech Publica- tions, 2010, vol. 112, pp.171-178. <10.4028/www.scientific.net/AMR.112.171>. <hal-00800060>

Transcript of Links Between Machining Parameters and Surface Integrity in

Page 1: Links Between Machining Parameters and Surface Integrity in

HAL Id: hal-00800060https://hal.archives-ouvertes.fr/hal-00800060

Submitted on 13 Mar 2013

HAL is a multi-disciplinary open accessarchive for the deposit and dissemination of sci-entific research documents, whether they are pub-lished or not. The documents may come fromteaching and research institutions in France orabroad, or from public or private research centers.

L’archive ouverte pluridisciplinaire HAL, estdestinée au dépôt et à la diffusion de documentsscientifiques de niveau recherche, publiés ou non,émanant des établissements d’enseignement et derecherche français ou étrangers, des laboratoirespublics ou privés.

Links Between Machining Parameters and SurfaceIntegrity in Drilling Ni-Superalloy

Vincent Dutilh, Gilles Dessein, Joël Alexis, Géraldine Perrin

To cite this version:Vincent Dutilh, Gilles Dessein, Joël Alexis, Géraldine Perrin. Links Between Machining Parametersand Surface Integrity in Drilling Ni-Superalloy. Advanced Materials Research, Trans Tech Publica-tions, 2010, vol. 112, pp.171-178. <10.4028/www.scientific.net/AMR.112.171>. <hal-00800060>

Page 2: Links Between Machining Parameters and Surface Integrity in

This is an author-deposited version published in : http://oatao.univ-toulouse.fr/ Eprints ID : 6485

To link to this article : DOI: 10.4028/www.scientific.net/AMR.112.171

URL : http://dx.doi.org/10.4028/www.scientific.net/AMR.112.171

Open Archive TOULOUSE Archive Ouverte (OATAO) OATAO is an open access repository that collects the work of Toulouse researchers and

makes it freely available over the web where possible.

To cite this version : Dutilh, Vincent and Dessein, Gilles and Alexis, Joël and Perrin, Géraldine Links Between Machining Parameters and Surface Integrity in Drilling Ni-Superalloy. (2010) Advanced Materials Research, vol. 112 . pp. 171-178. ISSN 1662-8985

Any correspondence concerning this service should be sent to the repository administrator: [email protected]

Page 3: Links Between Machining Parameters and Surface Integrity in

Links between machining parameters and surface integrity in drilling Ni-superalloy

����������� �1, a���������������2, b�������� ����2, c�������������� ��1,

d�!� "#$�%�����������&��'���'�!���(���)*++*��� �#��

+ �,����������������������'������-������-�).��&��'���/�0����1�-�23*!2��� "����&������4�'���56�'�,�(���47���,8�����4�������6����47����9���4���1��6����47���

�8��������4:�����6�'�,�(���47��

����������(���.+*��������8���'�7��������8���;����������$��������8����������� ��� �������� �� ������ ���� �������������� ��� ��������� ���� ������ ������� ������������������ ��� ��������� ���� ������ ����� ��� ���������� ���� �������� ��� ���� �� ��� � ����� �� � ���������� �������� ����������� ���������� ���� ���� ������ ������ ��� ��������� ���� �������� ��� ������ ������������������� ������� ��� �������� ������� �� � �� ���� ��� ���� ����� ��������� ���� ����� �� � ������������� ��� �� ��������������!���������������������������������!������������������� �������� ����������������������!������������������������������������������������������ ���� ��������� ��� ���� ����� ��� ��� � ���������� ����� �� !�� ������ �� ������ ��� ���� ������ ������������� ��������������� ����������� ���������������������������������� ����"#$%&�'(()*+,������ �-����)����).��������� �� � ���������������� ������� ���������� ���� ���� �������������$��/��)������������������� � ���������� ������ ������ ��� �������� �� 01*�*� ��� ����� ��� �� 2)� �� �������� ����������������� ������3����������4������ ������������# ��#���#���� �.�������� ����!��������56���)�����7� �� � ������ �������������� ���� � �����!���� ���� ��������� 8�� 9� �� � :�� ;��������'��������.���������;'.�������������������)��� ��������� ����������������������!������� ������� ������������� ���� ������ � ���� ��� ������������� ���� �������������� ����� ��� ���� ���������������� ���#�������� ������������!���� ������������� �� ���!���� ���� �������� ��� ������� ���� ����� � � �������� �������������������������������������

���� ���� ����� �������� ��������� ���� �� ��� ���� ��<���� � ��� ������ ��������� ��� ������� ������������������ ��� ����� ��� �� ����� ��������� �� � �� ������� � ��� ��������� ���� ������ ����������� ���������� ��� $��/��=���� ��������� �� ����� � �� � ���� ����� ���������� ��� ���� ������������� ��������������� ������� ����������������������������������� ��� ����������� �������������������������������������������������>��� ������������� ������!������������������ ����������5������7� ������ �� �������������� �������� ���� �� ��� ���� ����� !��� ��� ���������� ���� 5������7� ��� ������ ��� ������������������ ���"--'$����<�����" ������-����������.�������������?������������$�!���������������@���'������-���������!��������!�����'�������"����'���������������������� ������� ������������������������������ �������������� ���������� ��� ����������������������������������������������������!��/�����������������/����!��������������� �������� ������������������������������������������������-%.��-����)����).�������������� ����������!����� ������������������������� ������ ����� ���� ��� ������� �������� ������� ����� !���� �� � ��������� 6�� �������� !��� ���������� ������� �������� ������ ��� �� ��� ��� ������������� ���� ���������� �� � ���� �������� ��� ����� ��������������������!���������������������������������� ������!������������������������� ����� ����'�������"����'�������������������"--'$���������� #��������!����/�� ���� ���������������!����������������������� ������������������������

Page 4: Links Between Machining Parameters and Surface Integrity in

������ ����������$��/����������������������AB�.'��C+,���������������������������������� �������������������������� ����� ������ ����� ��� � ��������� ������� ������������ ��� ��������� ������ � � ������ �� ���������� ������������������������AB�.'��C+,�D�������������������1���������������� ����������������� #--� ����� � ������� � ������� γ� � ����� � ���������� � ������� ��� ��������� $��/��)��������"�$�� γE� ����������� �� � ���� �������� ���� �� �������� �������� ����� ����� �� � ���������?������� ������ ���������� γE� ���� �������� ������� ��� ���� ������ ���� ����� �� � ����� ����� ��� γE� �������� � ���������������������������γ������ �F1G���'������� $��� -�� -�� ��� .�� "�� 6� #�� H� ;�� .�� -�� -� ?� ;����� H��� 1C�*� 13� 3�C*� +�C*� +�+*� 1� �� ,�,1*� �� �� �� �� �� ���� � �� 1I�*� 1*�*� *�+*� 2�+*� +�C*� 1�*� ,�*� ,�,3,� ,�+� ,�1� ,�1� ,�,*� ,�1*� ,�,1�

������1J�-������������AB�.'��C+,�D��F!������KG��.���� �� ��� ��� ���� ���������� ��� ���������� ���/��)���� ��������� !���� ������� � ���� ��!� ��� ���������� ������������ ��������A �����C+,�F+��2��3��*G��#������������������<������������� ����!���������!������ ��� ����������������������$��/��)������������������������/��������������������������!������������� ����������������������/�!������������ ���E���������������������������������F+G��������!������������ ���������������������������� �������������������������������������/�������!����� ����������� ����� ����/�!��������� ��� �������� ��������� � ���!��/���� �������� � ���� ��� �����/�!������� �����������)��� ��������������H����)��� �����������������������������������F3�� *G�� ��� ����� ������� ������������������������ �� ��������� ��������� ��/�� �������� ����������� ���������� ��� ���������� ��� ���� ����� �� � !��/� ��� ������ �������� � ��� ���� ���������� �� � ����������������������������������F+��2��3G��%��� ��� ���� ���� ��������� ���� ��� �������� �� ����� ����������� �� ���� ������ ��� ���� ����������������� �� � ���� �� ����� ���� ��� ���� ���������� ��� ����� �������� ���� ���� �������� ������ "������������� ��������������!������."$L�&?���<����FCG����!���������� ��������� ����� ����������1'M,1����1'M,+������������������������������������������C1I��� ���(3�������������������!������������J� ��������� ������ �������������� ������������ � �������� ����� ��� � ��� ������ ����������%������� �������� ��������� ������������������!����������������� �������������������������F+��2��(��IG��?������F+G���� ����� �������������5������������7������������ ������ ����� ��������-%.������ ������ FNG�� ���� ����� ������� ����� ���� ������ � ��� ���� ������������ ��� ���� ������ �����!������������J� ������ � ��������� ����� � �������� ��� �� �� � ������)����������� ������� � ������%��������������� ������������� ��������!����� ���������5�������� � ������� ��������7� ���E������������������������������������������ ����������� ������������� ���������� � ������������������������������������-��������������������������� ��������������������� ���� ���!�� �������������������������!�������������� ���������������.���� ����� � ��� �� � ���� ���������� ��� �������� ���� �����!���� ���� ���� ���� ����� � ��� �������� ���� �������� ��� ���� ���� �� ��� �� L�!������ ���� � ������������� ���������������� ������ ��� ��� � ������� �������� ������� ��� �� ��� �!���� #��� � ������ ��� � ������ ��� ��������������������������������������������������������������� ���������������������������!����������������������F+��CG�������������!������������������������������������������ ��������FCG��

��������������������

�����������!�����!�������� �����������!����∅I,��������� ��������������� ������������� ������������������������������������������������������������� �������������� ���� �������������������������������������������� �����������������������������������������O�I�";�.���� �������� ���O�31,�L>2,������������ �������������!�������� ����� ������������������������!� ��������������������������������

Page 5: Links Between Machining Parameters and Surface Integrity in

�������������∅1*�*���� ����������-��� �����!�������������������������"�$������ ������ ����� ������ ����� ��� ���� ������������� ��� ������� �� ����� ����� ������� �3� ����� !����� ���� � ����������������� ���������������������������������"�������������!������ ��������%������>41,**�2)� ���������������������������������1*/6��� ����������� ���#�����%�).H�����������������������������������!�� ���������� � ��� �� 3� ���������4������ ����������� �# �� #��� #�� �� �.���� ���� ����!��������56���)�����7��� ������������������������� ������!�������� ���������8��9��� �:��#��������!�� ����� ������������������������� �����������(��������������� ������!�����/��������������� �������������� ���� ������������������� ������� ������������ ������������������� ������������� �������������� ��������2���������� �������������������1������

� � �#������1J����' ������������������ ����' ��������������

���������������������� ��<������� ��� ���� !��/� �� ��� �������� ���� ��������� �������� ���� �������� ��� ������ ���!��������� ����������� ������ �� � ������� ���������� ��������� �������� 1���� #��� ���� � �������������� ����� !�� ����� ���� ����� ���� ��� -%.� ����� ������ ��� ������ �� ����� ������ ��� ����������� �������6�� � �E������������������������� ����� ����� ������������ ���������������������� ��������� �� �� ∅1*�*� ��� �������� ��� �� ��)����� ∅12� ��� �� �� ��� ����������� ���������������������������������������������������������������������������������������� ����!�����������)�����∅12��������������������/������������������������������������������������������ ����� ��������-%.������ �������������!�������������������������!������������ ����������� ���� �������� �� � �� � ���� ��� � ������� ���� ��� ��!��� ������� �������� �������������4����"� ����� ��������������!������������������!������������������� ������������������������ �!���� �� � � ��� ������ ����� ��� � ������!�� ���� ���� �� � ��� �� ��������������!���� ���� �������������������� �!�������� ������������������ ���������� ����������� ������������� �����������3��;������� �������� ������������ ���� ��������� � ��� ����� ��������� �1�� � ������ � ����� ���� '(()*+,)I������F+G��!�����!�� ����� ����� �������������� ��������������!��!�������������������������������!���� �� �� ���� ����������� ��� 1�+*� ���� L�!������ ����� ��������� ������� � �� ��� � ��������� �� �����!� � ����/��� ��� ������� �� �������� �������6�� ���� � �!����� ��������� �������� �� � �� � ������ ��������� ��� ��6��������� �����������!��������!������� ������������ ����������������� ������������� ��������������� �������������� ����� �����������

�1��

3�-��������4������

B������������

"�������������

;�� ���� ��;�����

:�

8�

9�

��������

×××

=+3,

�������

××

=P

I,,,����� �� �

�××

=+

��� ���

Page 6: Links Between Machining Parameters and Surface Integrity in

��������

����������� �� �� ������� ������� ����� ��� ���� �������� ��� ������ !�� �!� �������� 3�� !���������� ������ ����������������������������4�����#����4�����.����4�����?����1���� ��������� �������� ������������������������������� ���������+����������������������������������� ��!�������� �������!��������������������������������������� ��������������+����� ���������� ��������������������������������� ���������+����%���������+���� �+���!������ ������������������>��Q�1N��R���� �� � �� Q� ,�1���R�������������������� ������� � � ��� ���� ��!��� �������������� ��� ����1���+��������������

,

1,,,

+,,,

2,,,

* 1, 1* +, +* 2, 2*

��

����

� �

!�������"

4�����.��4�����?��

,

1,,,

+,,,

2,,,

, ,�1 ,�+ ,�2

��

����

� "

��������"

4���4�����.��4�����?��

,

,�2

,�(

,�N

1�+

1�*

,

+

3

(

I

1,

* 1, 1* +, +* 2, 2*

���

�#�

"

�$�

�#�

"

!�������"

&�&�

)+,

)1(

)1+

)I

)3

,,

1,

+,

2,

3,

*,

, ,�1 ,�+ ,�2

%&�

����

����

����

�#�

"

��

����

��&���

�"

��������"

-����������

-���� �������

�#������+J����;���������������������R����������� �����;���������������������R���� �����&�������R�

���������� �� ��L�������������R���� ����� ���� ����� ���� ���������� ��� ����� ����� �� ���� ���� ��� ��� ���� ��������� �� ��� ���� ������ ��/��� ������������� ���� ����4���������������!������� ��� � � ������������������������ ������!�� �!��6�� ������� ������������ ���� � ���������������+������� ���� ��� ���������!������������J�;����������������������������4�����4����������/��� �����������!������������������� �����������������+�J�&���&������ �����������������������+ J��������������������� ��������������������!�������������������������� �� � ��� ���� -%.������ �������6�� ����� ����� �� ����� ���� ���) ���������� �� � ���� �������������������� ��������&� ����&���� .������������� � ���������� !���� �� �� ��� �� ��� ��� ������ ���������� � ������ ����� ���� ��� ���� ������� ���������� ����������� %���������� !���� ������� � !���� ���������� ��������� ��������� �;'.)#'�� @'%D� C,,,� #�� �� � ��� ������� ������������ >''-%��$�11,,������� ������� ���������� ���������� �� ��!�� ��� ������+� ����������������������������� ��� ������������������ �� ������������' ������������������� �������������������������������������������������� ���� ����� !�� ����� ��� �!�� ������� ���������� ����S� ���� ������� ��������� �� � ������������������ �������������� �������� ��� ���� ����� �� �� �� ���� ����� ��������� ������ � ���J���������� ��������� �����)����/� �1,)+,� T�� �������� �������� 2��� ������ � ������ �� � ����� �� ������������������� ���������������(����

��� ���

��� ��

Page 7: Links Between Machining Parameters and Surface Integrity in

����� ;���������������� .�������������.�������������������� .������������������

-��������� ;�������.��������������

;�������.�����

���������

L����������� ������

.����������������� ������

L������ ������������������� ������

.����������� ����������

&�� ���������

;��������������������������

;������-���/������������

%�����������-���������H����

#��/������;����������������D���

?���/����

&������������&� ����������������

B������ �������

6������������&���������� �

�����

B������������.����)��� ������������������� ����

B��������������� ������������������������� ����

������+J�;����������������� �����������

�#������2J�;������������������������J���������������������)����/��������������

�%���������(���!����������� �������������������UV��� ��� ��������������������� ����� ����UV�����!����� �� ������ �� ������ ������������ �� ������������ ������ ���� �������!�� ��������� �!���� ��� 8)���� ��� ������� � !���� '������ B������� ;����������� �;BB� H&A-4'&�� �� � ��������)��� ��� �������!�����!��������� ���� ��������� ������ ��� ��� ��������.���� �������!������� ��������������������!���������������������������������� ������� ��� ���� ����� �� � ���� ��������� !���� ���� ������� �������� ������ �� � ������� � ��� ��������� ���� ���������� ������ ���� ���� ��������� ������ �� -�������� !���� ������� �� ����� �������� ����������������&��Q�,�I�T���� �&��Q�(�T�������������������.����)����/����������� ;'.�������� ��81,,,� ���� ���� �����������B������ � ������ �� ������������ ���1T�� ����/����"� ��������� ������������������� �����������!������������������������������ ���;������� ���������� ������� ������� � ��� ��������� �� ��!� �������� �� � ������� ������� ����� ��������������� ����� �!����-%.������ ��������������3���

�#������3J�-��������� ��� ������������������ ������

!* !3 +* +3 <*

*�*3

*�!*

*�!3

*�+*

*�+3

*�<*

�:�����������

<*�

+*�

=*�

�����,���>�8�

�����������;����������������(��5��������77��������;��

�(�����8������5����������:��,����'�7��������8���;���(���%#$��(���

7�?((4��

@!A

���?(4(��@!A

2*�

%'����8���(�

.����)����/�

�"� �"� "�

-�����

�� ���������

Page 8: Links Between Machining Parameters and Surface Integrity in

���������������� ������� ��� ����� ���;������������������������������������������� ����������������������� ������������������ ���������������������������������������������������� ���������������������!������������ ��������������� ������������������������!�� �����������������������6������ ��!��� ������������ �!������������� ���������������� ��� ������ �����������!����������� � �����!��������� ���������� ����� ��������������!������������ �����������+��!����������������� �������� ������������� �������� �����������������������!����!��������������������!������������������� ����������!���������������� ������ ��������������������� � ������������L�!������ ������������������������������������ �!�������������� ���������������������������� �������� �!��� ������ ������ ��� ���� �� ��� �!��� ����� 56���)�����7�� �� ��!��� ������ ������������ �!��� ������ ��������� � ��� ���� ������������ "� ������������ �1�+� ��� 1�3� ���� ���� ������ ����!���� ��� � ��� ��� � � � ��� �� ��� ��� ������ ���� ������ � ����������� ���������� �� ��� ��� ����56���)�����7������ � ��!���������������� � ��� ����������������!��������� ��"������������������������!��������� ��������������������� �����������������������!�������������� � ���!��������������������������!�����������!������������������������������������������������

��+��

% ������� �� ������� ��������&� '� (� ���� ) ��� ����� ��� ���� ��������� !�� ����� ���������������� ���!���� ������� ���������� ��������� �� � ������ ����� � �� ���� ����� ���� !�� ���� ������������������������������������������!���!�������� ��������������������

�#������*J����-������������������R?�!�������B��������A �����C+,������������� ���������������

�%���������*���!���������� ���������������������������������������������/�����������������������������������!�������� �!�������������������������������!� ����� ��1�������������������������������������!����� ��� �� �!�������� ����������������������������!���!����������������������� ������ ��������������������� �������������������������������������� ����������������!��������� ��������������������������������������������� ���� ������������������������������ � ��������������������)��� ���!������������������������ ����$��/��)�����������������������F(G��#������������ ��� ���� �������*���!����������� ��������A �����C+,���� ������������� ��� �������������� ����'������B�������;������������;BB�H&A-4'&������������������������!���������� �!������ ������������������������������ �����������������)��� ���!���������������������������������#������ (� ������ �������� � ����� ��� ��������� ���!���� �!�� ����� ������ �� � �!��������������������������"��������������!����������!����������������������������������������������!������������/�������� ������ ��������� ���������������������� �����������������������!���� ������ ������ ���������������������������������������� ��!������������������������������� �

H�������� ����� ��B��������A �����C+,�

��� ���

&�/�������

-��������������

#���/������

��� � � ×+×= ω

8)&���������$��4W�

Page 9: Links Between Machining Parameters and Surface Integrity in

���� �� ���� ����/��� ��� �� ����� ������� � ������ ��� ���� ���� ����� �� ���� �������� �!��� ��������������� ����������������#������(���� �(����!����� ������������������������������2��� �21�������� ������������������� ��� �������(���!���������������� ����� ������ � ������� ��������� ��� �������(��!�����!���������������������!������������� ���!�������� ������ ��������"������)��� �����������(�������������� ��!�������!����������������������������������������������� ����������������������������������������!�����!����������� ������������������������������������!���������� ������������������������������������� �����������3������!������ ����� ���������� ����������������������� ����!�����������

�#������(J�.�������������������2������ ����21����������������������������������.����)��� ���

��������������������� � ��?�!������������������!��������/������������� ��������

*������ �� ������� ��������&� '� ������� ������� ����������.������������� ����������� ������ ����!����������� � ��������������3�������������������������������� ���������������������������� ����� ������������3�1�������������������������!� ���������������������������������������� ��F1G�� !����� ��� ��� ����� ���� � ����� ������� �������� ������������ ���� ����� ��� ������ ��� ���������������� ����� ��������� ���� ������� ���������� ����������� %�� ���� ������ ��� �� ���� ������ ����� ������ �� ������� ����� �������� ����� ����-%.������ ������ ��������3�������-%.� ������!��!���� ����� � ��� ���� � �������������� �������������� ������� ���� ���� ���� �������� �� � ��������� ����� ������ ����� ��������� ������ !����� �������� �� � ����� ���������� ������ ��� � ������ ��� ������������������������������������>�R��!�� �!����������������� ������������� ����������� ��������������������������������������������������������!�����/��������������������4����������������� ������ ������ ��������� ���� �� �������� ��� ������������ ;������� �������� ������ �� ���� ��/�� �����������������������������!��������������������

% ����� ����� ���� ��������� !�� ����� ������ � ���� ������ ����� ��� � ���������� ���� ���� ��� � ��� -%.������ �������������!������������ �!�������������������� ���������������� ����!��������

*�*+ *�+ *�) *�B

!

3

!*

!3

+*

+3

<*

<3

� ��������������������������������������

� ���

�������

�������

�����

�������

����

�����

��

� ������������������� �

)**@3** 3**@2** 2**@.** .**@B**

L����X������������������� �������

B������ �������

B������ �������

���

����� ���

Page 10: Links Between Machining Parameters and Surface Integrity in

�� ����������������������.������������������������������������� ����������� ��� ������� ������ � ��������� ����������������� ��������������������6������������� � �������������� � ������ ����� �!�������������������������������!��������������� ����������������!���������������� � ������ ����� ������������������������������� ������������������ ������������������������� ������ ����� ��������/����!��������������������������� �������� ���������� �� � ����� ������� � ���� ���/� ��� ���� -%.� ����� ������ ��!�� � ������ �������������������������������������� ���������������������������!������������������������������������ � ��� ���� ����� �� ��� � �� � ����� ����������� ������ ����� � � ������ ���� ������� ������������ �� � ���� �������������� �������������� ������� !���� ��������� � ��� ���� �������� �!�������������� ���� �������������� ��� ����������� ��������� ����� ���� �������� ��� ���� ������������ ��� ����������� ������������!�����<���� ���������������������������������!������������������������������ �� �������� ��� �������� ���� ������� ���������� �� � ����� ������� ���� ���� ������ ����� ��!���� �������������������������������������������������� ������������������������������������������������� ��������������������������

�+� ,������������������������� ���������������������������� ���� �������������'�������-��������Y�;�������#����!��/�?����������#?CR+,,C)+,11���� ��������������������������+12I**��

����������

F1G� L����?�����?�"�;��&�� ��.���������������������������������������������������/�������������� ������ ����/� ���!��� ��� �������� ��� ���/��)���� ��������� A ����� C+,D��� @������� ��� .��������;��������� �'������������"�33I��(C=CN��+,,(����

F+G� ��� ?������� Z�� �� �[������������� �[�������� ��� ���������� �� �E���[����[� �� ������� �� �\������[�� ��� ������ �[����] ��� ��� �E�������� C1I�&� )�B[�������� ��� ��������������� �� ��������� ���?�����.�������������\�� �� ���������'����� ��.���� ��?�����+,,3���

F2G� "��;��������"��"����������� �� �4��&� �!��������� ����� �� � ������� ���������� �����!���� ���������� ��������/���������������C1I��@����������.��������?���������������������+,,��3+3)32+��+,,I����

F3G��@��4!�����B��" ������ �� �?��6����������� �������������$�)��� � ��������� ����������/������������J� ���������� ��� ����� ��������� ��� ��������� ������ �� � ��� ���� ����� @������� ���.��������?�����������������������?����-������� �?�������+,,I���

F*G� '�%�� '���!��� 4��� ����������� ��� �������������� ��� ��������)��)���� �������� ������������������������@���������������X�.�����������3*��12*2)12(C��+,,*����

F(G� "�� ;�������� @�� L������ �� � 4�� &� �!���� "�� ������� ��� ���� ��� ���� ����� �������� � �����������C1I��.��!�������������@����������.��������?���������������������1C2��2*N)2(C��+,,(���

FCG� ."$L�&?�?��<�����������������?�����-�������!����.����������������?�� ����L��������������&��������?��������.� ����������������#�����&������+,,*����

FIG� B��$��������&��-��B�!���B��4��"��!�����6��>�������� �?��H�!������������������������� ������������ � �����������������������������������������@����������.�������������� �.������������33��1+*)123��+,,3���

FNG� "#$%&�$����$#�'(()*+,���6��/�������������������������)�-���������)����������+,,,���

Page 11: Links Between Machining Parameters and Surface Integrity in

������ � ��������� ������� �� ������ ���������10.4028/www.scientific.net/AMR.112

!�"� #��$�� �����% &���'����� �� ������ (��%���� � )�����% *�+��,�������10.4028/www.scientific.net/AMR.112.171 )-( ��������[3] A. Sharman, A. Amarasinghe, and K. Ridgway. Tool life and surface integrity aspectswhen drilling and hole making in Inconel 718. Journal of Materials Processing Technology ,200, 424-432 (2008).doi:10.1016/j.jmatprotec.2007.08.080

[5] E.O. Ezugwu. Key improvements in the machining of difficult-to-cut aerospacesuperalloys. nternational Journal of Tools & Manufacture 45, 1353-1367 (2005).doi:10.1016/j.ijmachtools.2005.02.003

[6] A. Sharman, J. Hughes, and K. Ridgway. An analysis of the residual stresses generatedin Inconel 718(TM) when turning. Journal of Materials Processing Technology , 173, 359-367 (2006).doi:10.1016/j.jmatprotec.2005.12.007

[8] D. Novovic, R. C. Dewes, D. K. Aspinwall, W. Voice, and P. Bowen. The effect ofmachined topography and integrity on fatigue life. International Journal of Machine Toolsand Manufacture, 44, 125-134 (2004).doi:10.1016/j.ijmachtools.2003.10.018