Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes...

24
1 5488 (supersedes 5453)---0806---J9 RTC---8065 II Link-Belt Cranes Technical Dat a Specifications & Capacities Telescopic Boom Rough Terrain Crane 65 ton (60.0 metric ton) CAUTION: This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator’s Manual to determine allowable crane lifting capacities and assembly and operating procedures.

Transcript of Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes...

Page 1: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

15488 (supersedes 5453)---0806---J9

RTC---8065 IILink-Belt Cranes

Technical DataSpecifications & Capacities

Telescopic Boom Rough Terrain Crane65 ton (60.0 metric ton)

CAUTION: This material is supplied forreference use only. Operator must refer toin---cab Crane RatingManual andOperator’sManual to determine allowable crane liftingcapacities and assembly and operatingprocedures.

Page 2: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Page 3: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

5488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

Table Of ContentsBoom, Attachments, and Upper Structure 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Boom 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Boom Head 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Boom Elevation 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Auxiliary Lifting Sheave --- Optional 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hook Blocks and Balls --- Optional 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fly --- Optional 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fly Inserts --- Optional 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operator’s Cab and Controls 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Swing 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electrical 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Load Hoist System 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Load Hoist Performance 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2M Main and Optional Auxiliary Winches 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydraulic System 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Counterweight 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Carrier 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .General 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Outriggers 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Steering and Axles 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Suspension 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tires and Wheels 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Brakes 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electrical 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Engine 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Transmission 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Carrier Speeds and Gradeability 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fuel Tank 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydraulic System 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pump Drive 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Axle Loads 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .General Dimensions 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Working Range Diagram 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Boom Extend Modes 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Main Boom Lift Capacity Charts -- Standard 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fully Extended Outriggers --- 360˚ Rotation 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .On Tires --- Stationary --- Boom Centered Over Front Between Tire Tracks 11. . . . . . . . . . . . . . . . . . . . . . . . .On Tires --- Pick & Carry (Creep) --- Boom Centered Over Front 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .On Tires --- Stationary --- 360˚ Rotation 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fly Attachment Lift Capacity Charts -- Optional 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fully Extended Outriggers --- 360˚ Rotation 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 ft Main Boom Length --- 2˚ Fly Offset 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 ft Main Boom Length --- 15˚ Fly Offset 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 ft Main Boom Length --- 30˚ Fly Offset 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 ft Main Boom Length --- 45˚ Fly Offset 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 4: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Main Boom Lift Capacity Charts -- Metric 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fully Extended Outriggers --- 360˚ Rotation 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .On Tires --- Stationary --- Boom Centered Over Front Between Tire Tracks 16. . . . . . . . . . . . . . . . . . . . . . . . .On Tires --- Pick & Carry (Creep) --- Boom Centered Over Front 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .On Tires --- Stationary --- 360˚ Rotation 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fly Attachment Lift Capacity Charts -- Optional 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fully Extended Outriggers --- 360˚ Rotation 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35.05 m Main Boom Length --- 2˚ Fly Offset 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35.05 m Main Boom Length --- 15˚ Fly Offset 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35.05 m Main Boom Length --- 30˚ Fly Offset 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35.05 m Main Boom Length --- 45˚ Fly Offset 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 5: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

15488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

Boom, Attachments, and Upper StructureJ BoomDesign --- Four section, formed construction of extra hightensile steel consisting of one base section and three tele-scoping sections. The first telescoping section extendsindependently by means of one double---acting, singlestage hydraulic cylinder with integrated holding valves.The second and third telescoping sections extend propor-tionally by means of one double---acting, single stage cylin-der with integrated holding valves and cables.BoomS 38 ft---115 ft (11.6 ---35.0m) four section full power boomS Two mode boom extension: A---max mode provides su-perior capacities by extending the first telescoping sec-tion to 63 ft 8 in (19.4m). Standard mode synchronizesall the telescoping sections proportionally to 115 ft(35.0m). Controlled from the operator’s cab.

S Mechanical boom angle indicatorS Maximum tip height for A---max mode is 73 ft 6 in (22.4m)and standard mode is 123 ft 9 in (37.7m).Boom HeadS Four 16.5 in (41.9cm) root diameter nylon sheaves tohandle up to eight parts of line

S Easily removable wire rope guardsS Rope dead end lugs on each side of the boom headS Boom head is designed for quick---reeve of the hookblockBoom ElevationS One double acting hydraulic cylinder with integral hold-ing valve

S Boom elevation: ---3˚ to 78˚Auxiliary Lifting Sheave --- OptionalS Single 16.5 in (41.9m) root diameter nylon sheaveS Easily removable wire rope guardsS Does not affect erection of the fly or use of the main headsheavesHook Blocks and Balls --- OptionalS 40 ton (36.3mt) 4 sheave quick---reeve hook block withsafety latch

S 60 ton (54.4mt) 4 sheave quick---reeve hook block withsafety latch

S 70 ton (63.5mt) 5 sheave quick---reeve hook block withsafety latch

S 8.5 ton (7.7mt) swivel and non---swivel hook balls withsafety latch

Fly --- OptionalS 35 ft (10.7m) one piece lattice fly, stowable, offsettable to2˚, 15˚, 30˚, and 45˚. Maximum tip height is 158 ft(48.2m).

S 35 ft---58 ft (10.7 ---17.7m) two piece bi---fold lattice fly,stowable, offsettable to 2˚, 15˚, 30˚, and 45˚. Maximumtip height is 180 ft 5 in (55.0m).Fly Inserts --- OptionalS One 16 ft (4.9m) lattice insert, equipped with two 16.5 in(41.9cm) root diameter nylon sheaves, to be mountedbetween the boom head and fly options. Maximum tipheight is 196 ft (59.7m).

S Two 16 ft (4.9m) lattice inserts, one equipped with two16.5 in (41.9cm) root diameter nylon sheaves, to bemounted between the boom head and fly options. Maxi-mum tip height is 211 ft 7 in (64.5m).

J Operator’s Cab and ControlsEnvironmental Cab --- Fully enclosed, one person cab ofgalvaneal steel structure with acoustical insulationEquipped with:S Tinted and tempered glass windowsS Extra---large fixed front window with windshield wiper andwasher

S Swing up roof window with windshield wiperS Sliding left side door with large fixed windowS Sliding rear and right side windows for ventilationS Six way adjustable, cushioned seat with seat belt andstorage compartment

S Engine dependent warm---water heater with air ducts forfront windshield defroster and cab floor

S Defroster fan for the front windowS Bubble levelS Circulating fanS Adjustable sun visorS Dome lightS Cup holderS Fire extinguisherS Left side viewing mirrorS Two position travel swing lockAir Conditioning --- Optional --- Integral with cab heatingsystem utilizing the same ventilation outlets

Page 6: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

2 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Steering Column --- Pedestal type with tilt and telescopefunctions for operator comfort. Column includes the follow-ing controls and indicators:Left and right levers include:

S Horn buttonS Turn signal switchS Driving light switchS Transmission direction switchPanel mounted switches for:

S Travel park brakeS Steer mode selectorS 2/4 wheel drive/range selectorS Transmission gear selectorS Hazard flasherPanel mounted indicator/warning lights for:

S Transmission temperatureS Engine oil pressureS Travel park brakeS Service brakeS Turn signalsS Rear wheel offset---optionalS Emergency steer --- optionalArmrest Controls --- Two dual axis hydraulic joystick con-trollers or optional single axis hydraulic controllers for:S SwingS Boom hoistS Main rear winchS Auxiliary front winch --- optionalS Drum rotation indicationS Drum rotation indicator activation switchS Winch high/low speed and disable switch(es)S Third wrap selector switch --- optionalS Telescopic override switchesS Warning horn buttonS Swing park brakeOutrigger Controls --- Hand held control box with umbilicalcord gives the operator the freedom to view operation whilesetting the outriggers.Foot ControlsS Boom telescopeS Swing brakeS Engine throttleS Service brakeRight Front Console --- Controls and indicators for:S Engine ignition S Console dimmer switchS Engine throttle lock S Bubble levelS Function disable S 12 volt power connectionS Front windshield wiper S Air conditioning --- optionaland washer S Boom floodlight --- optional

S Cab floodlights S Rotating beacon/StrobeS Warning horn light --- optionalS Heating controls S Third wrap indicator ---

optional

Cab Instrumentation --- Ergonomically positioned, analoginstrumentation for crane operation including:S Engine coolant temperature with warning indicatorS Hydraulic oil temperature with warning indicatorS Fuel level with warning indicatorS TachometerS Transmission temperature with warning indicatorS Voltmeter with warning indicatorRated Capacity Limiter --- Microguard graphic audio---visual warning system integrated into the dash with anti ---two block and function limiter. Operating data availableincludes:S Crane configurationS Boom length and angleS Boom head heightS Allowed load and % of allowed loadS Boom angleS Radius of loadS Actual loadS Operator settable alarms (include):S Maximum and minimum boom anglesS Maximum tip heightS Maximum boom lengthS Swing left/right positionsS Operator defined area (imaginary plane)Internal RCL Light Bar --- Optional --- Visually informs theoperator when crane is approaching maximum load capac-ity with a series of green, yellow, and red lights.External RCL Light Bar --- Optional --- Visually informs theground crew when crane is approaching maximum loadcapacity with a series of green, yellow, and red lights.

J SwingMotor/Planetary --- Bi ---directional hydraulic swing motormounted to a planetary reducer for 360˚ continuoussmooth swing at 2.0 rpmSwing Park Brake --- 360˚, electric over hydraulic, (springapplied/hydraulic released) multi ---disc brake mounted onthe speed reducer. Operated by a switch from the opera-tor’s cab.Swing Brake --- 360˚, foot operated, hydraulic applied discbrake mounted to the speed reducerSwing Lock --- Two---position swing lock (boom over frontor rear) operated from the operator’s cab360˚ Positive Swing Lock --- Optional --- Meets New YorkCity requirement

J ElectricalSwing Alarm --- Audio warning device signals when theupper is swinging.LightsS Two working lights on front of the cabS One rotating amber beacon on top of the cab --- optionalS One amber strobe beacon on top of the cab --- optionalS Boom floodlight --- optional

Page 7: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

35488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

J Load Hoist SystemLoad Hoist Performance

Main (Rear) and Auxiliary (Front) Winches --- 3/4 in (19mm) RopeMaximum Line Pull Normal Line Speed High Line Speed Layer Total

Layer lb kg ft/min m/min ft/min m/min ft m ft m1 17,182 7 793.6 171 52.1 322 98.1 86 26.2 86 26.22 15,523 7 041.1 190 57.9 356 108.5 96 29.3 182 55.53 14,157 6 421.5 208 63.4 390 118.9 105 32.0 287 87.54 13,011 5 901.7 226 68.9 425 129.5 114 34.7 401 122.25 12,038 5 460.3 245 74.7 459 139.9 123 37.5 524 159.76 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- 133 40.5 657 200.3

Wire Rope ApplicationDiameter

TypeMaximum

Permissible Loadin mm lb kg

Main (Rear)Winch

Standard 3/4 19 6x19 IWRC --- right regular lay (Type DB) 16,800 7 620.4Optional 3/4 19 18x19 rotation resistant --- right regular lay (Type RB) 12,920 5 860.4

Auxiliary (Front)Winch

Standard 3/4 19 6x19 IWRC --- right regular lay (Type DB) 16,800 7 620.4Optional 3/4 19 18x19 rotation resistant --- right regular lay (Type RB) 12,920 5 860.4

2M Main and Optional Auxiliary WinchesS Axial piston, full and half displacement (2---speed) motorsdriven through planetary reduction unit for positive con-trol under all load conditions

S Grooved laggingS Power up/down mode of operationS Drum rotation indicator(s)S Drum diameter: 13 in (33.0cm)S Rope length:S Front: 500 ft (152.4m)S Rear: 600 ft (182.9m)

S Maximum rope storage: 657 ft (200.3m)S Terminator style socket and wedgeS Hoist drum cable followers --- optionalThird wrap indicator --- optional --- Visually and audiblywarns the operator when the wire rope is on the first/bottomlayer and when the wire rope is down to the last threewraps

J Hydraulic SystemCounterbalance Valves --- All hoist motors, boom extendcylinders, and boom hoist cylinders are equipped withcounterbalance valves to provide load lowering and pre-vents accidental load drop when hydraulic power is sud-denly reduced.

J CounterweightTotal of 12,000 lb (5 443kg) of counterweight pinned to theupper structure frame with capacities for the 12,000 lb(5 443kg) configuration

Page 8: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

4 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

CarrierJ GeneralS 10 ft 7 in (3.22m) wideS 14 ft 7 in (4.45m) wheelbase (centerline of first axle tocenterline of second axle)Frame --- Box---type, torsion resistant, welded constructionmade of high tensile steel. Equipped with front and reartowing and tie---down lugs, tow connections, and accessladders.

J OutriggersBoxes --- Two double box, front and rear welded to carrierframeBeams and Jacks --- Four single stage beams with Con-fined Area Lifting Capacities (CALCt) provide selectableoutrigger extensions of full, intermediate, and retracted.Hydraulically controlled from the operator’s cab with inte-gral check valves.Pontoons --- Four lightweight, quick release, 23.5 x 23.5 in(59.7 x 59.7cm), steel pontoons with contact area of 460 in2(2 968cm2) can be stored for road travel in storage rackson the carrier.Main Jack Reaction --- 90,500 lb (41 050kg) force and197 psi (1 358kPa) ground bearing pressure

J Steering and AxlesSteering --- Four independent modes consisting of twowheel front, two wheel rear, four wheel, and crab. Eachmode is controlled from the steering wheel and is selectedby a switch in the operator’s cab.Drive --- Two modes: 4 x 2 and 4 x 4 for off highway travelAxle 1 --- Steered, non---driven for 4 x 2 and steered, drivenfor 4 x 4Axle 2 --- Steered, driven

J SuspensionFront --- Rigid mount to the carrier frameRear --- The rear axle is suspended on the oscillation cylin-ders with motion of the axle controlled by a four bar linkagesystem. The oscillation cylinders lockout when the upperstructure rotates 2.5˚ past centerline.S Hydro---gas rear suspension --- optional

J Tires and WheelsFront and Rear --- Four (single) 26.5 x 25---26 ply rating,earthmover type tires on steel disc wheelsS Spare tires and wheels --- optional

J BrakesService --- Full hydraulic, dual circuit, disc type brakes onall wheel endsParking/Emergency --- Spring applied type, acting on frontaxle

J ElectricalTwo batteries provide 12 volt starting and operationLightsS Front lighting includes two main headlights and two park-ing/directional indicators.

S Side lighting includes two parking/directional indicatorsper side.

S Rear lighting includes two parking/directional indicators,two parking/brake lights, and two reversing lights.

S Other equipment includes hazard/warning system, cablight, instrument panel light, and signal horn.

J EngineSpecification CAT C6.6

Numbers of Cylinders 6

Cycle 4

Bore and Stroke: inch (mm) 4.13 x 5.00 (105 x 127)

Piston Displacement: in3 (L) 403 (6.6)

Max. Brake Horsepower: hp (kW) 225 (167.8) @ 2,200 rpm

Peak Torque: ft lb (Nm) 727 (986) @ 1,400 rpm

Alternator: volts --- amps 12 --- 150

Crankcase Capacity: qt (L) 18.4 (17.4)

S Mechanically driven fan and thermostatically controlled radiator

J TransmissionPowershift --- Three speed with high/low range for 6 for-ward and 6 reverse gears. Front axle disconnect for two orfour wheel drive. Front axle disconnects in high range.

Page 9: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

55488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

J Carrier Speeds and Gradeability

Spicer Speed Gradeability(@ stall)

Gear Ratio mph km/h % Grade

6thForward &Reverse2WD/Hi

0.82 23.2 37.34 2.4

5th 2.25 9.7 15.61 10.1

4th 4.67 4.8 7.88 23.5

3rdForward &Reverse4WD/Low

2.4 9.1 14.64 10.9

2nd 6.54 3.5 5.63 34.8

1st 13.6 1.7 2.74 99.5

Based on a gross vehicle weight of 88,000 lb (39 916kg).Crane operating angle must not exceed 35˚ (77% grade).

J Fuel TankOne 75 gallon (283.9L) capacity tank

J Hydraulic SystemAll functions are hydraulically powered allowing positiveprecise control with independent or simultaneous operationof all functions.Main PumpsS One two section fixed displacement gear pump for thefront/rear winches and boom hoist circuits.

S One two section fixed displacement gear pump for theswing/telescope, power steering/outrigger/telescope,service brake, and oscillation circuits.

S Combined pump capacity of 138 gpm (522.4Lpm)Hydraulic Reservoir --- 153 gal (579.2L) capacity equippedwith sight level gauge. Diffusers built in for deaeration.Filtration --- One 10 micron, full flow line filter in the controlcircuit. All oil is filtered prior to return to reservoir. Accessi-ble for easy filter replacement.

J Pump DriveAll pumps are mounted on the transmission and mechani-cally driven by the diesel engine.S Front/rear winches and boom hoist pumps can be dis-connected with a manual pump disconnect to aid in coldweather starting --- optional.

Page 10: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

6 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Axle Loads

Base crane with full tank of fuel

Gross VehicleWeight (1)

Upper Facing Front Upper Facing RearFront Axles Rear Axles Front Axles Rear Axles

lb kg lb kg lb kg lb kg lb kg83,952 38 080 39,888 18 093 44,064 19 987 35,690 16 189 48,262 21 891

Pintle hook, front 13 6 16 7 ---4 ---2 16 7 ---4 ---2Pintle hook, rear 13 6 ---5 ---2 17 8 ---5 ---2 17 8Rear steer indicator 6 3 0 0 6 3 0 0 6 3Hydro---gas suspension 48 22 17 8 31 14 17 8 31 14Pump disconnect 39 18 7 3 32 15 7 3 32 15Operator in cab 250 113 134 61 116 53 103 47 147 67Hoist drum follower --- main 67 30 ---28 ---13 95 43 92 42 ---25 ---11Auxiliary winch with 500 ft(152.4m) wire rope 538 244 ---100 ---45 638 289 610 277 ---72 ---33

Hoist drum follower --- auxiliary 67 30 ---17 ---8 84 38 80 36 ---13 ---6Substitute type “DB” rope withtype “RB” rope --- main winch 126 57 ---44 ---20 170 77 164 74 ---38 ---17

Substitute type “DB” rope withtype “RB” rope --- auxiliary winch 105 48 ---19 ---9 124 56 119 54 ---14 ---6

Substitute 500 ft (152.4m) wirerope with 600 ft (182.9m) ---auxiliary

104 47 ---19 ---9 123 56 118 54 ---14 ---6

Remove 600 ft (182.9m) wire ropefrom rear (main) winch ---642 ---291 226 103 ---868 ---394 ---835 ---377 193 88

Remove 500 ft (152.4m) wire ropefrom front (auxiliary) winch ---538 ---244 100 45 ---638 ---289 ---610 ---277 72 33

Emergency steering 260 118 35 16 225 102 212 96 48 22360˚ mechanical swing lock 140 64 52 24 88 40 81 37 59 27Air conditioning 220 100 57 26 163 74 152 69 68 31Floodlight to front of boom basesection 7 3 13 6 ---6 ---3 ---6 ---3 13 6

Fly mounting brackets to boombase section for fly options 176 80 316 143 ---140 ---63 ---149 ---67 325 147

35 ft (10.67m) offsettable fly ---stowed 1,591 722 2,504 1 136 ---913 ---414 ---995 ---451 2,586 1 173

35---58 ft (10.67---17.68m)offsettable fly --- stowed 2,263 1 026 3,162 1 434 ---899 ---408 ---1,016 ---461 3,279 1 487

Auxiliary lifting sheave 110 50 297 135 ---187 ---85 ---193 ---88 303 13760 ton (54.4mt) 4---sheave hookblock at bumper 1,109 503 1,635 742 ---526 ---239 ---583 ---264 1,692 767

70 ton (63.5mt) 5---sheave hookblock at bumper 1,400 635 2,064 936 ---664 ---301 ---736 ---334 2,136 969

8.5 ton (7.7mt) hook ball atbumper 360 163 531 241 ---171 ---78 ---189 ---86 549 249

60 ton (54.4mt) 4---sheave hookblock at boom head 1,109 503 2,883 1 308 ---1,774 ---805 ---1,831 ---831 2,940 1 334

70 ton (63.5mt) 5---sheave hookblock at boom head 1,400 635 3,640 1 651 ---2,240 ---1 016 ---2,312 ---1 049 3,712 1 684

8.5 ton (7.7mt) hook ball at boomhead 360 163 936 425 ---576 ---261 ---595 ---670 955 433

Tire Maximum Allowable Axle Load @ 25 mph (40.2km/h)

26.5 x 25 (26---PR) 51,040 lb (23 151kg)

(1) Adjust gross vehicle weight and axle loading according to component weight.Note: All weights are ±3%.

Page 11: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

75488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

General Dimensions

Not To Scale

C of RotationL

C of RotationL

Turning Radius --- Front Wheel (4x2) Steering English MetricWall to wall over carrier 43’ 2” 13.2mWall to wall over boom attachment 53’ 4” 16.3mCurb to curb 41’ 6” 12.6mCenterline of tire 40’ 1” 12.2m

Tail Swing English MetricWith counterweight 13’ 8.25” 4.2m

Turning Radius --- All Wheel (4x4) Steering English MetricWall to wall over carrier 26’ 6” 8.1mWall to wall over boom attachment 38’ 1” 11.6mCurb to curb 24’ 10” 7.6mCenterline of tire 23’ 6” 7.2m

38’ 0” (11.6m)

7’ 0”(2.1m)

1’ 0”(0.3m)

12’ 2”(3.7m)

6’ 10.25”(2.0m)

21.9˚25.2˚

7’ 8”(2.3m)

6’ 11”(2.1m)

12’ 0”(3.7m)

12’ 0”(3.7m)13’ 6.75”(4.1m)

13’ 6.75”(4.1m)

45’ 5.5”(13.9m)

5’ 8.5”(1.7m)

7’ 5.5”(2.3m)@ 0˚5’ 5.75”(1.7m)@ ---3˚

10’ 2”(3.1m)

9.75”(0.2m)

13.25”(0.3m)

23”(0.6m)

8’ 2.5”(2.5m)

9’ 6.75”(2.9m)

10’ 7.5”(3.2m)

17’ 9.25”(5.4m)

24’ 0”(7.3m)

2’ 7.5”(0.8m)

1’ 3”(0.4m)

12’ 5.75”(3.8m)@ 0˚

10’ 7.75”(3.2m)@ ---3˚

Without counterweight N/A N/A

Page 12: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

8 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Working Range Diagram

15˚OFFSET

10

2040

50

60

70

80

90

100

30110130

120

170

160

150

140

Operating Radius From Axis Of Rotation In Feet (Meters)

HeightInFeet(Meters)AboveGround

(3.0)

(6.1)(12.2)

(15.2)

(18.3)

(21.3)

(24.4)

(27.4)

(30.5)

(9.1)(33.5)(39.6)

(36.6)

(51.8)

(48.8)

(45.7)

(42.7)

180(54.9)170(51.8)160(48.8)150(45.7)140(42.7)130(39.6)120(36.6)110(33.5)100(30.5)90

(27.4)80

(24.4)70

(21.3)60

(18.3)50

(15.2)40

(12.2)30(9.1)20(6.1)10(3.0)0

95’ (29.0m) +35’ (10.7m)

115’ (35.1m)Mode “B”

105’ (32.0m)

95’ (29.0m)

85’ (25.9m)

75’ (22.9m)

63.6’ (19.4m)Mode “A”

65’ (19.8m)

55’ (16.8m)

38’ (11.6m)Mode “A” & “B”

78˚ MaxBoom Angle

45’ (13.7m)

20˚

30˚

40˚

50˚

60˚70˚

10˚

45˚OFFSET 30˚

OFFSET

10’(3.0m)

8.5’(2.6m)

95’ (29.0m) +58’ (17.7m)115’ (35.1m) +35’ (10.7m)

190(57.9)

200(61.0)

210(64.0)

220(67.1)

180(54.9)

200(61.0)

190(57.9)

210(64.0)

115’ (35.1m) +58’ (17.7m)

115’ (35.1m) +74’ (22.6m)

115’ (35.1m) +90’ (27.4m)2˚ OFFSET

115’ (35.1m) +16’ (4.9m)

Boom+FlyLengthInFeet(Meters)

BoomLengthInFeet(Meters)

C of RotationL

Page 13: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

95488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

Boom Extend ModesBoom Mode “A” (A--max)

Boom Mode “B” (Standard)

Only inner mid section telescopes.

Inner mid, outer mid, and tip sectionstelescope simultaneously.

Base SectionTip Section308” (7.82m) Stroke

BoomLength

38’(11.58m)

45’(13.72m)

55’(16.76m)

63.6’(19.39m)

75’(22.86m)

85’(25.91m)

95’(28.96m)

105’(32.00m)

115’(35.05m)

Outer Mid Section308” (7.82m) Stroke

Inner Mid Section308” (7.82m) Stroke

Base SectionInner Mid Section308” (7.82m) Stroke

BoomLength38’

(11.58m)

45’(13.72m)

55’(16.76m)

65’(19.81m)

Page 14: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

10 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Main Boom Lift Capacity Charts -- StandardFully Extended Outriggers -- 360˚ Rotation

(All Capacities Are Listed In Pounds)

Radius(ft)

Boom Length (ft) Radius(ft)38 45 55 63.6/65 75 85 95 105 115

9 130,000 910 120,000 108,200 106,100 1012 108,900 104,600 98,100 71,900** 1215 91,600 91,200 86,200 71,900** 54,000 1520 67,100 66,800 66,400 66,100** 54,000 55,900 46,400 2025 52,000 52,600 53,000 53,000 53,700 49,900 41,800 36,200 28,100 2530 41,800 42,500 43,000 43,400 43,600 43,800 37,800 34,200 28,100 3035 33,300 33,900 34,200 34,400 34,600 34,000 30,700 28,100 3540 26,400 26,700 26,900 27,100 27,200 27,300 25,700 4045 21,200 21,600 21,800 22,000 22,100 22,100 22,200 4550 17,700 18,000 18,100 18,200 18,300 18,300 5055 14,800 15,000 15,100 15,200 15,300 15,400 5560 12,700 12,800 12,900 13,000 13,000 6065 10,800 11,000 11,100 11,200 11,200 6570 9,400 9,500 9,600 9,700 7075 8,100 8,200 8,300 8,300 7580 7,100 7,100 7,200 8085 6,100 6,200 6,200 8590 5,300 5,400 9095 4,600 4,600 95100 4,000 100105 3,400 105

** 63.6 A---max Mode

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

Page 15: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

115488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

On Tires -- Stationary -- Boom Centered Over Front Between Tire Tracks(All Capacities Are Listed In Pounds)

Radius(ft)

Boom Length (ft) Radius(ft)38 45 55 65 75 85

10 64,000 1012 56,800 56,400 1215 48,500 48,900 39,500 1520 38,400 39,100 39,500 30,400 2025 29,000 29,700 30,100 30,400 22,400 2530 20,600 21,400 21,900 22,200 22,400 17,200 3035 16,000 16,600 16,900 17,100 17,200 3540 12,900 13,300 13,400 13,600 4045 10,200 10,600 10,800 11,000 4550 8,500 8,800 8,900 5055 6,800 7,100 7,300 5560 5,700 5,900 6065 4,600 4,800 6570 3,900 7075 3,100 75

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

Page 16: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

12 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

On Tires -- Pick & Carry (Creep) -- Boom Centered Over Front(All Capacities Are Listed In Pounds)

Radius(ft)

Boom Length (ft) Radius(ft)38 45 55 65 75 85

10 63,000 1012 55,200 54,900 1215 46,300 46,700 39,500 1520 35,700 36,100 36,600 30,400 2025 28,300 28,800 29,300 29,600 22,400 2530 20,600 21,400 21,900 22,200 22,400 17,200 3035 16,000 16,600 16,900 17,100 17,200 3540 12,900 13,300 13,400 13,600 4045 10,200 10,600 10,800 11,000 4550 8,500 8,800 8,900 5055 6,800 7,100 7,300 5560 5,700 5,900 6065 4,600 4,800 6570 3,900 7075 3,100 75

On Tires -- Stationary -- 360˚ Rotation(All Capacities Are Listed In Pounds)

Radius(ft)

Boom Length (ft) Radius(ft)38 45 55 65 75 85

10 47,700 1012 39,000 39,500 1215 26,800 27,400 27,800 1520 16,200 16,800 17,300 17,600 2025 10,500 11,100 11,700 12,000 12,200 2530 6,800 7,500 8,100 8,400 8,600 8,800 3035 5,000 5,600 5,900 6,200 6,300 3540 3,800 4,100 4,400 4,600 4045 2,400 2,800 3,000 3,200 4550 1,700 1,900 2,100 5055 1,100 1,200 55

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

Page 17: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

135488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

Fly Attachment Lift Capacity Charts -- OptionalFully Extended Outriggers -- 360˚ Rotation

(All Capacities Are Listed In Pounds)115 ft Main Boom Length

2˚ Fly Offset115 ft Main Boom Length

15˚ Fly Offset

Radius(ft)

Fly Length (ft) Radius(ft)

Fly Length (ft)35 58 74 90 35 58 74 90

35 13,100 35

40 13,100 40

45 13,100 8,800 45 11,800

50 12,900 8,700 7,200 50 11,500

55 12,600 8,400 7,200 5,500 55 11,200

60 12,300 8,200 7,200 5,500 60 11,000 7,100

65 12,000 8,000 7,000 5,400 65 10,700 6,900 5,900

70 10,600 7,700 6,500 5,000 70 10,400 6,700 5,600 4,500

75 9,200 7,500 6,100 4,700 75 9,800 6,500 5,300 4,200

80 8,000 7,200 5,800 4,300 80 8,600 6,300 5,000 3,900

85 7,000 7,000 5,400 4,100 85 7,500 6,100 4,700 3,600

90 6,200 6,700 5,100 3,800 90 6,600 5,900 4,500 3,400

95 5,400 5,900 4,900 3,600 95 5,800 5,700 4,300 3,200

100 4,700 5,200 4,600 3,300 100 5,100 5,600 4,100 3,000

105 4,100 4,600 4,400 3,100 105 4,400 5,200 3,900 2,800

110 3,600 4,100 4,000 2,900 110 3,900 4,600 3,700 2,700

115 3,100 3,600 3,500 2,800 115 3,300 4,000 3,500 2,500

120 2,600 3,100 3,000 2,600 120 2,900 3,500 3,400 2,400

125 2,200 2,700 2,600 2,500 125 2,400 3,100 3,000 2,200

130 1,900 2,300 2,200 2,200 130 2,000 2,700 2,600 2,100

135 1,500 2,000 1,900 1,900 135 1,600 2,300 2,200 2,000

140 1,200 1,600 1,500 1,500 140 1,300 1,900 1,800 1,900

145 1,400 1,200 1,200 145 1,600 1,500 1,500

150 1,100 1,000 150 1,300 1,200 1,200

155 800 155 1,000 900 900

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

Page 18: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

14 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)

115 ft Main Boom Length30˚ Fly Offset

115 ft Main Boom Length45˚ Fly Offset

Radius(ft)

Fly Length (ft) Radius(ft)

Fly Length (ft)35 58 74 90 35 58 74 90

40 40

45 45

50 50

55 9,900 55

60 9,700 60 8,900

65 9,500 65 8,800

70 9,400 70 8,700

75 9,200 5,600 75 8,600

80 9,100 5,500 4,200 80 8,600

85 8,000 5,300 4,000 3,200 85 8,400 4,900

90 7,000 5,200 3,800 3,000 90 7,300 4,800 3,400

95 6,200 5,100 3,700 2,900 95 6,400 4,700 3,300 2,600

100 5,400 5,000 3,500 2,700 100 5,600 4,700 3,200 2,500

105 4,700 4,900 3,400 2,500 105 4,900 4,700 3,100 2,300

110 4,100 4,900 3,200 2,400 110 4,200 4,600 3,000 2,200

115 3,500 4,500 3,100 2,300 115 3,600 4,600 2,900 2,100

120 3,000 3,900 3,000 2,100 120 4,200 2,800 2,000

125 2,500 3,400 2,900 2,000 125 3,700 2,700 1,900

130 2,100 3,000 2,800 1,900 130 3,200 2,700 1,800

135 2,500 2,500 1,800 135 2,700 2,600 1,700

140 2,200 2,200 1,700 140 2,200 2,300 1,600

145 1,800 1,800 1,600 145 1,900 1,600

150 1,400 1,400 1,500 150 1,600 1,500

155 1,100 1,100 1,200 155 1,400

160 800 900 160 1,000

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.

Page 19: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

155488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

Main Boom Lift Capacity Charts -- MetricFully Extended Outriggers -- 360˚ Rotation

(All Capacities Are Listed In Kilograms)

Radius(m)

Boom Length (m) Radius(m)11.58 13.7 16.8 19.39/19.8 22.9 25.9 29.0 32.0 35.05

2.5 60 000 2.53 54 800 49 000 48 100 33.5 50 650 48 650 45 550 32 600** 3.54 46 900 45 250 42 300 32 600** 44.5 42 250 42 050 39 500 32 600** 24 450 4.55 37 800 37 600 37 100 32 600** 24 450 56 31 000 30 850 30 650 30 500** 24 450 25 550 21 150 67 26 050 25 900 25 750 25 650** 24 450 23 700 19 750 78 22 300 22 600 22 850 23 000 23 100 22 050 18 500 16 400 12 800 89 18 200 18 500 18 700 18 850 18 950 19 050 17 300 15 650 12 800 910 15 050 15 300 15 450 15 550 15 600 15 650 14 550 12 800 1012 10 900 11 050 11 100 11 200 11 250 11 250 11 300 1214 8 150 8 300 8 400 8 450 8 500 8 500 8 550 1416 6 450 6 550 6 600 6 650 6 650 6 700 1618 5 250 5 300 5 350 5 400 5 400 1820 4 250 4 300 4 350 4 400 4 400 2022 3 500 3 550 3 600 3 600 2224 2 900 2 950 3 000 2426 2 400 2 450 2 450 2628 2 000 2 050 2830 1 650 3032 1 350 32

** 19.39 A---max Mode

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

Page 20: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

16 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

On Tires -- Stationary -- Boom Centered Over Front Between Tire Tracks(All Capacities Are Listed In Kilograms)

Radius(m)

Boom Length (m) Radius(m)11.58 13.7 16.8 19.8 22.9 25.9

3 29 000 33.5 26 500 3.54 24 200 24 050 44.5 22 250 22 450 17 900 4.55 20 550 20 750 17 900 56 17 700 17 950 17 900 13 750 67 13 350 13 600 13 750 13 750 78 10 400 10 700 10 900 11 000 10 150 89 8 350 8 650 8 850 8 950 9 000 7 800 910 7 100 7 350 7 450 7 500 7 550 1012 5 250 5 400 5 450 5 500 1214 3 800 4 000 4 100 4 150 1416 3 000 3 100 3 150 1618 2 350 2 400 1820 1 750 1 850 2022 1 400 22

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

Page 21: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

175488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

On Tires -- Pick & Carry (Creep) -- Boom Centered Over Front(All Capacities Are Listed In Kilograms)

Radius(m)

Boom Length (m) Radius(m)11.58 13.7 16.8 19.8 22.9 25.9

3 28 550 33.5 25 900 3.54 23 400 23 550 44.5 21 250 21 450 17 900 4.55 19 400 19 600 17 900 56 16 400 16 650 16 850 13 750 67 13 350 13 600 13 750 13 750 78 10 400 10 700 10 900 11 000 10 150 89 8 350 8 650 8 850 8 950 9 000 7 800 910 7 100 7 350 7 450 7 500 7 550 1012 5 250 5 400 5 450 5 500 1214 3 800 4 000 4 100 4 150 1416 3 000 3 100 3 150 1618 2 350 2 400 1820 1 750 1 850 2022 1 400 22

On Tires -- Stationary -- 360˚ Rotation(All Capacities Are Listed In Kilograms)

Radius(m)

Boom Length (m) Radius(m)11.58 13.7 16.8 19.8 22.9 25.9

3 21 550 33.5 16 500 3.54 13 200 13 400 44.5 10 850 11 050 11 200 4.55 9 050 9 300 9 450 56 6 550 6 800 7 000 7 100 67 4 900 5 150 5 350 5 450 78 3 700 3 950 4 150 4 300 4 350 89 2 800 3 050 3 250 3 400 3 500 3 550 910 2 350 2 550 2 700 2 800 2 850 1012 1 550 1 700 1 800 1 850 1214 850 1 000 1 100 1 150 1416 450 550 650 16

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

Page 22: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

18 5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Fly Attachment Lift Capacity Charts -- OptionalFully Extended Outriggers -- 360˚ Rotation

(All Capacities Are Listed In Kilograms)35.05 m Main Boom Length

2˚ Fly Offset35.05 m Main Boom Length

15˚ Fly Offset

Radius(m)

Fly Length (m) Radius(m)

Fly Length (m)10.67 17.68 22.56 27.43 10.67 17.68 22.56 27.43

12 5 900 12

14 5 900 4 000 14 5 350

16 5 750 3 850 3 250 16 5 150

18 5 600 3 750 3 250 2 500 18 5 000

20 4 750 3 600 3 150 2 400 20 4 850 3 100 2 650

22 3 950 3 450 2 900 2 200 22 4 200 3 000 2 450 1 950

24 3 300 3 300 2 650 2 000 24 3 550 2 850 2 300 1 800

26 2 800 3 000 2 450 1 850 26 2 950 2 750 2 150 1 650

28 2 350 2 550 2 300 1 700 28 2 500 2 650 2 000 1 500

30 1 950 2 150 2 100 1 550 30 2 100 2 400 1 850 1 400

32 1 650 1 850 1 800 1 400 32 1 750 2 050 1 750 1 300

34 1 350 1 550 1 500 1 300 34 1 450 1 750 1 650 1 200

36 1 100 1 300 1 250 1 200 36 1 200 1 450 1 450 1 100

38 900 1 050 1 050 1 050 38 950 1 250 1 200 1 000

40 700 900 850 850 40 750 1 000 950 950

42 550 700 650 650 42 550 800 800 800

44 550 500 500 44 650 600 600

46 400 46 500 450 450

48 48 350

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

Page 23: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

195488 (supersedes 5453)---0806--- J9

RTC---8065 IILink-Belt Cranes

Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Kilograms)

35.05 m Main Boom Length30˚ Fly Offset

35.05 m Main Boom Length45˚ Fly Offset

Radius(m)

Fly Length (m) Radius(m)

Fly Length (m)10.67 17.68 22.56 27.43 10.67 17.68 22.56 27.43

18 4 450 18

20 4 300 20 4 000

22 4 200 22 3 950

24 3 750 2 500 24 3 900

26 3 150 2 400 1 800 1 450 26 3 300 2 200

28 2 650 2 350 1 700 1 350 28 2 800 2 150 1 550

30 2 250 2 300 1 600 1 250 30 2 350 2 150 1 450 1 150

32 1 900 2 250 1 550 1 150 32 1 950 2 100 1 400 1 050

34 1 550 1 950 1 450 1 050 34 1 600 2 100 1 350 1 000

36 1 250 1 650 1 400 1 000 36 1 750 1 300 900

38 1 000 1 350 1 300 900 38 1 450 1 250 850

40 800 1 150 1 150 850 40 1 200 1 200 800

42 900 900 800 42 950 1 000 750

44 700 700 750 44 800 700

46 550 550 550 46 600 650

48 400 400 48 450

This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 75% of the tipping loads and on tires do not exceed 65% of the tipping loads.

Page 24: Link-Belt RTC8065 Specifications and Capacities · 2020. 9. 24. · 5488 (supersedes 5453)---0806---J9 3 Link-Belt Cranes RTC---8065 II J Load Hoist System Load Hoist Performance

5488 (supersedes 5453)---0806--- J9

RTC---8065 II Link-Belt Cranes

Link--Belt Construction Equipment Company Lexington, Kentucky www.linkbelt.comRLink--Belt is a registered trademark. Copyright 2006. We are constantly improving our products and therefore reserve the right to change designs and specifications.