Liberator II Hammermill - Sudenga Industries · Liberator II hammermills provide economical and...
-
Upload
duongxuyen -
Category
Documents
-
view
223 -
download
0
Transcript of Liberator II Hammermill - Sudenga Industries · Liberator II hammermills provide economical and...
The reversible hinge door simplifies installation and makes screen replace-ment safe and easy!
• 6” x 18” (15.2 x 45.7 cm) diameter full circle grinding chamber• Direct Drive hub assembly with 15 hammers (optional 30 hammers)• 7½ to 30 HP motors
The locking latch and hollow core door gasket keeps dust to a minimum.
Liberator II hammermills provide economical and dependable solutions to your grinding needs in a small footprint.
Liberator II HammermillSINCE 1888
Stretch your grinding dollars
with a new Sudenga Liberator II Hammermill.
Side View
11¾”(30 cm)
CAPACITIES
Box 8 • 2002 Kingbird Ave. • George, IA 51237 USA1-888-SUDENGA (783-3642) • 1-712-475-3301 • Fax: 1-712-475-3320
[email protected] • www.sudenga.com
SUDENGAINDUSTRIES, INC.
Top View
A
25½”(65 cm)
31¾”(81 cm)
41¼”(105 cm)
3”(8 cm)
SIZE (HP) FRAME DIM. “A”7.5 213TC 28” (71 cm)10 215TC 30” (76 cm)15 215TC 30” (76 cm)20 256TC 31½” (80 cm)25 284TSC 33½” (85 cm)30 286TSC 33½” (85 cm)
All motors are 3-phase and 230/460 volt.
DRY CORN - lb./kg. per hr.
Screen Size 7½ hp 10 HP 20 HP 30 HP1/8” (3.2 mm) 3,750 (1,705 kg) 5,000 (1,705 kg) 10,000 (4,545 kg) 14,000 (6,365 kg)5/32” (4 mm) 4,500 (2,045 kg) 6,000 (2,725 kg) 12,000 (5,455 kg) 17,000 (7,725 kg)
3/16” (4.8 mm) 5,250 (2,385 kg) 7,000 ( 3,180kg) 14,000 (6,365kg) 20,000 (9,090 kg)7/32” (5.6 mm) 6,000 (2,725 kg) 8,000 (3,635 kg) 16,000 (7,275 kg) 22,000 (10,000 kg)1/4” (6.4 mm) 6,750 (3,070 kg) 9,000 (4,090 kg) 18,000 (8,180 kg) 25,000 (11,365 kg)
Center Feed Doors provide longer hammer life and more uniform particle size.
6-09
DRY BARLEY - lb./kg. per hr.
Screen Size 7½ HP 10 HP 20 HP 30 HP1/8” (3.2 mm) 1,650 (750 kg) 2,200 (1,000 kg) 4,400 (2,000 kg) 6,600 (3,000 kg)5/32” (4 mm) 1,950 (885 kg) 2,600 (1,180 kg) 5,200 (2,365 kg) 7,800 (3,545 kg)
3/16” (4.8 mm) 2,325 (1,060 kg) 3,100 (1,410 kg) 6,200 (2,820 kg) 9,300 (4,227 kg)7/32” (5.6 mm) -- -- --1/4” (6.4 mm) -- -- --
29”(74 cm)
Front View
Bottom Feed Door
Mills are available with bottom or center feed doors. Both feature heavy duty plate magnets that keep metal out of the hammers and feed.
Center Feed Door
Infeed inlets are 4” (10.2 cm) or 6” (15.2 cm) diameter. Discharge can be left or right hand.
Liberator II Hammermill
The reversible hinge door simplifies installation and makes screen replace-ment safe and easy!
• 6” x 18” (15.2 x 45.7 cm) diameter full circle grinding chamber• Direct Drive hub assembly with 15 hammers (optional 30 hammers)• 7½ to 30 HP motors
The locking latch and hollow core door gasket keeps dust to a minimum.
Liberator III hammermills are an economical and dependable solution to your grinding requirements in a small footprint.
Liberator III HammermillSINCE 1888
Stretch your grinding dollars
with a new Sudenga Liberator III Hammermill.
SINCE 1888SINCE 1888
The reversible hinge door simplifies installation and makes screen replace-ment safe and easy!
The locking latch and hollow core door gasket keeps dust to a minimum.
Liberator III hammermills are an economical and dependable
with a new Sudenga
Box 8 • 2002 Kingbird Ave. • George, IA 51237 USA1-888-SUDENGA (783-3642) • 1-712-475-3301 • Fax: 1-712-475-3320
[email protected] • www.sudenga.com
SUDENGAINDUSTRIES, INC.
Top ViewA
25½”(65 cm)
31¾”(81 cm)
Horsepower Motor Frame Dimension “A”7.5 213TC 28¾” (74 cm)10 215TC 30¾” (78 cm)15 215TC 30¾” (78 cm)20 256TC 32¼” (82 cm)25 284TSC 34¼” (87 cm)30 286TSC 34¼” (87 cm)
All motors are 3-phase and 230/460 volt.
Center Feed Doors provide longer hammer life and more uniform particle size.
1-10
CAPACITY - DRY BARLEY - lb./hour (kg/hour)Screen Size 7½ HP 10 HP 20 HP 30 HP1/8” (3.2 mm) 1,650 (750 kg) 2,200 (1,000 kg) 4,400 (2,000 kg) 6,600 (3,000 kg)5/32” (4 mm) 1,950 (885 kg) 2,600 (1,180 kg) 5,200 (2,365 kg) 7,800 (3,545 kg)
3/16” (4.8 mm) 2,325 (1,060 kg) 3,100 (1,410 kg) 6,200 (2,820 kg) 9,300 (4,227 kg)7/32” (5.6 mm) -- -- --1/4” (6.4 mm) -- -- --
Front View
Mills are available with bottom or center feed doors. Both feature heavy duty plate magnets that keep metal out of the hammers and feed.
Feed inlets are 4” (10.2 cm) or 6” (15.2 cm) diameter. Discharge can be left or right hand.
Liberator III Hammermill
33¾”(86 cm)
3”(8 cm)
45½”(116 cm)
12” (31 cm)
Side View
CAPACITY - DRY CORN - lb./hour (kg/hour)Screen Size 7½ hp 10 HP 20 HP 30 HP1/8” (3.2 mm) 3,750 (1,705 kg) 5,000 (1,705 kg) 10,000 (4,545 kg) 14,000 (6,365 kg)5/32” (4 mm) 4,500 (2,045 kg) 6,000 (2,725 kg) 12,000 (5,455 kg) 17,000 (7,725 kg)
3/16” (4.8 mm) 5,250 (2,385 kg) 7,000 ( 3,180kg) 14,000 (6,365kg) 20,000 (9,090 kg)7/32” (5.6 mm) 6,000 (2,725 kg) 8,000 (3,635 kg) 16,000 (7,275 kg) 22,000 (10,000 kg)1/4” (6.4 mm) 6,750 (3,070 kg) 9,000 (4,090 kg) 18,000 (8,180 kg) 25,000 (11,365 kg)
29”(74 cm)
21½”(55 cm)
2” (5 cm) 1½” (4 cm)
Center Feed Door
Bottom Feed Door