LH201_9900sc Sandvik
4
Technical Specification Sandvik LH201 9-900 S-C 2008-07-10 © 2008 Sandvik Mining and Construction APPLICATION Sandvik LH201 is a true compact and flexible full Diesel loader for narrow vein mining. The highest possible rate of productivity is ensured by fast and easy one pass loading. Sandvik LH201 layout is designed for good visibility and balance. This and the powerful four-wheel-drive articulated chassis ensure fast and safe manoeuvering in tight spaces. All the service points are well protected but easy to access. CAPACITIES Tramming capacity 1 000 kg (2 200 lb) Breakout force, lftt 10.7 kN - 1 094 kg (2 407 lb) Breakout force, tilt 36.9 kN - 3 766 kg (8 285 lb) Tipping load 2 941 kg (6 470 lb) Bucket std. 0.54 m³ (0.7 yd³), 500 BNH lip BUCKET MOTION TIMES Raising time 2.6 sec. Lowering time 1.5 sec. Tipping time 4.1 sec. WEIGHTS Operating weight 3 650 kg (8 030 lb) Total loaded weight 4 650 kg (10 230 lb) Shipping weight Axle weights without load Front axle 1 120 kg (2 460 lb) Rear axle 2 530 kg (5 570 lb) Axle weights with load Front axle 2 630 kg (5 790 lb) Rear axle 2 020 kg (4 440 lb) Unit weight is dependent on the selected options. DRIVING SPEEDS FORWARD AND REVERSE Loaded, max 9 km/h (5.6 mph) 1215 1645 1525 1430 4600 1030 2045 1055 1050 1840 3190 1890 36° 220 1/4
Transcript of LH201_9900sc Sandvik
Technical Specification Sandvik LH2019-900 S-C2008-07-10
© 2008 Sandvik Mining and Construction
APPLICATIONSandvik LH201 is a true compact and flexible full Dieselloader for narrow vein mining.
The highest possible rate of productivity is ensured byfast and easy one pass loading.
Sandvik LH201 layout is designed for good visibility andbalance.This and the powerful four-wheel-drive articulatedchassis ensure fast and safe manoeuvering in tightspaces.
All the service points are well protected but easy toaccess.
CAPACITIESTramming capacity 1 000 kg (2 200 lb)Breakout force, lftt 10.7 kN - 1 094 kg (2 407 lb)Breakout force, tilt 36.9 kN - 3 766 kg (8 285 lb)Tipping load 2 941 kg (6 470 lb)Bucket std. 0.54 m³ (0.7 yd³), 500 BNH lip
BUCKET MOTION TIMESRaising time 2.6 sec.Lowering time 1.5 sec.Tipping time 4.1 sec.
WEIGHTSOperating weight 3 650 kg (8 030 lb)Total loaded weight 4 650 kg (10 230 lb)Shipping weightAxle weights without loadFront axle 1 120 kg (2 460 lb)Rear axle 2 530 kg (5 570 lb)Axle weights with loadFront axle 2 630 kg (5 790 lb)Rear axle 2 020 kg (4 440 lb)Unit weight is dependent on the selected options.
DRIVING SPEEDS FORWARD AND REVERSELoaded, max 9 km/h (5.6 mph)
1215
1645 1525 14304600
1030
2045
1055
1050
1840
3190
1890
36°
220
1/4
Technical Specification Sandvik LH2019-900 S-C2008-07-10
© 2008 Sandvik Mining and Construction
SERVICE CAPACITIESFuel tank 40 liters (10.5 gal.)Hydraulic oil tank 62 liters (16.4 gal.)Hydrostatic transmission oil tank 31 liters (8.2 gal.)
FRAMERear and front frame Welded steel constructionMaterial E 36.3Central hinge Spherical bearings
(large angle)
ENGINEDiesel engine Deutz F3L 912WOutput 33 kW (45 hp) / 2 500 rpmTorque 170 Nm / 1 500 rpmNumber of cylinder In line 3Displacement 2 827 cm³Cooling system Air cooledCombustion principle 4-stroke, 2-stage combustionElectric system 12 V starter and accessoriesAir filtering Oil bath air cleanerExhaust system Catalytic purifier
TRANSMISSIONHydrostatic transmission Variable flow
fully reversibleOne pump Linde, variable displacement
0 to 42 cm³/revOne motor Linde, fixed 35 cm³/rev
TRANSFER CASEType GearLocation Rear axle
AXLESFront and rear Tamrock, fixed
No-spin in front axleCentral hinge oscillation ± 10°
WHEELSTires 8.25 x 15Air pressure, front and rear 3.5 bar (350 kPa)
BRAKESDynamic service brake through the hydrostatictransmission.The parking and emergency brake is spring applied,hydraulically released multidisc oil immersed brakesinclosed on the transfer case.
STEERINGFull hydraulic, centre-point articulation, power steeringwith two double acting cylinders. Steering controlled bystick, interlock protection.Turning angle ± 36°Turning radius inner 1840 mm (72”)
outer 3190 mm (125”)Main components in steering system:
Main valve HPIControl valve DanfossSteering hydraulic cylinders 2 pcs, 60 mm (2.36”),
TamrockPressure settings:
Main relief valve 14.0 Mpa (140 bar)Shock load valves 17.5 Mpa (175 bar))
BUCKET HYDRAULICSFull hydraulic open center system with one gear pump.The oil flow from steering hydraulic pump is directed to bucket hydraulics when steering is not used.Equipped with mechanical dual control lever.Lift cylinder 1 pcs, ø100 mm (3.9”)Tilt cylinder 1 pcs, ø120 mm (4.7”)Pressure setting for:
Main relief valve 14.0 Mpa (140 bar)Bucket tilt 6.0 Mpa (60 bar)Bucket roll-back 18.0 Mpa (180 bar)Boom raise 18.0 Mpa (180 bar)Boom lower 6.0 Mpa (60 bar)
Main components:Bucket hydraulic cylinders TamrockControl valve Commercial hydraulicsFittings JIC
ELECTRICAL EQUIPMENTAlternator 45 ABattery 1 x 12 V, 95 AhStarter 1.7 kW, 12 VDriving and working lights font, 2 pcs (H1 55 W)
rear, 2 pcs (H1 55 W)
OPTIONAL EQUIPMENT*) Bucket size 0.5 m³ (0.7 yd³), width 950 mm (37”).FOPS-ROPS safety canopy.Reverse alarm.Emergency steering system.Complete spare wheel.*) EU, UL, CSA, AUS norms package.
*) replaces standard component
2/4
Technical Specification Sandvik LH2019-900 S-C2008-07-10
© 2008 Sandvik Mining and Construction
GRADEABILITY & SPEED
PRODUCTIVITY CURVE
0
10
20
30
40
50
60
0 1 2 3 4 5 6 7 8 9
GRADE (%)
SPEED (kph)
TONNESPER HOUR
0
10
20
30
40
50
60
0 50 100 150 200 250 300 350 400 450
ONE WAY DISTANCE IN METRES0 % 20 %
Basic data for calculations :
Payload 1 000 kgOverall speed limit 8.5 km/hFixed cycle time 0.5 min.Rolling resistance 3 %
Fixed cycle time includes the time for filling, dumping, turning and accelerating
Slope / Grade Hor./0 1:5/20Loaded speed (kph) 8.5 7.1Empty speed (kph) 8.5 8.5
3/4
Technical Specification Sandvik LH2019-900 S-C2008-07-10
Sandvik Mining and Construction reserves the right to change this specification without further notice.
Sandvik Mining and Construction Lyon S.A.S. B.P.46 - FR-69881 Meyzieu Cedex, FranceTel. +33 4 7245 2200, Telefax +33 4 7831 7980www.sandvik.com
DUMP DATA
CAGING DIMENSIONS
1500
2320
1745
1290600
835
42°
4/4
3698
3463
3453
1215
1215
991
1055
1055
1055
Bucket and canopy removed ...........................................3 287 kg
Bucket, canopy and lift arms removed ...........................3 107 kg
Bucket, canopy, lift arms, axles and tires removed.......2 372 kg
