Service Information

Rubber-to-metal component installation position in the axle support for the front axle

ZF Services GmbH Obere Weiden 12, 97424 Schweinfurt, Germany Technical Support Phone: +49 9721 4755555 Fax: +49 9721 4755556 techsupport.zf-services@zf.com www.zf.com

© ZF Services GmbH

Printed in Germany05497 EN

07.2011

1 / 2

SEAT Cordoba (6L2) / Ibiza IV (6L1) Skoda Fabia (6Y2, 6Y3, 6Y5) Volkswagen Fox (5Z1, 5Z3) / Polo (9N)

Fig.1: GMT 29710 01 Fig.2: GMT 34559 01

1 GMT 29710 01 5 Transverse control arm contact surface 2 Rubber plug 6 Mark on GMT 3 Transverse control arm contact surface 7 Mark on axle support 4 GMT 34559 01 8 Front axle support

Service Information

Rubber-to-metal component installation position in the axle support for the front axle

ZF Services GmbH Obere Weiden 12, 97424 Schweinfurt, Germany Technical Support Phone: +49 9721 4755555 Fax: +49 9721 4755556 techsupport.zf-services@zf.com www.zf.com

© ZF Services GmbH

Printed in Germany05497 EN

07.2011

2 / 2

NOTE Always replace rubber-to-metal omponents (GMT) in pairs. The modified GMT (4) replaces GMT (1).

Installing the GMT 1. Mark the GMT (4), as shown in Fig. 2 (6). 2. The contact surface for the control arm (5) must point to the axle support (8) or towards the

center of the vehicle 3. The mark (6) must align with the mark on the axle support (7). 4. In this position, press the GMT (4) into the axle support (8) using a suitable tool. The mark on the axle support (7) is cast below on the right side of the vehicle (Fig. 1, 2) and above on the left side of the vehicle.

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice