3

MANUFACTURER, DISTRIBUTOR AND STOCKIST

MANUFACTURER OF SPEEDLOCK :

After Cooler (Air-Cooled & Water-Cooled - Portable) Air-Cooled Dehumidifier (Portable / Stationary) Abrasive Blast Machines (Portable / Stationary) Abrasive Vacuum Recovery System (Portable / Stationary) Blast & Paint Chamber (Partial / Full Abrasive Recovery System) Blast & Paint Halls (Partial Abrasive Recovery System) Dust Collection System (Portable / Stationary) Dry Filter Spray Booth (Portable / Stationary) Rubber Roll-Up Door for Blast & Paint Chambers (up to 8m wide) Vertical Lift Up Door for Blast & Paint Halls (up to 50m wide) Related Accessories & Hardware: Air-Tools, Compressed Air Fittings, Hoses, Personal Safety Gear, etc. High Alloy Angular Steel Grit & Low-Carbon Steel Shot

DISTRIBUTOR FOR THE FOLLOWING BRANDS :

E.S.C.S (UK) Plural Component Spray Equipment & Accessories for Passive Fire-Proofing Material (PFP) & Fast Curing Epoxy Paints

DST-SPEEDLOCK (KOREA) Spray Painting Equipment & Accessories for Protective Coating Industry

GRACO (USA) Spray Painting Equipment & Accessories for Protective Coating Industry

TITAN (USA) Spray Painting Equipment & Accessories for Building & Construction Industries

DeFelsko (USA) Measuring Device & Instrument for Protective Coating Industry

Bullard (USA) Industrial Health & Safety Product

STOCKIST FOR THE FOLLOWING BRANDS :

CLEMCO (USA) Abrasive Blast Equipment & Accessories

MARCO (USA) Abrasive Blast Equipment & Accessories

ELCOMETER (UK) Measuring & Laboratory Instruments

PCWI (AUSTRALIA) Pin Holes / Holiday Detectors

W ABRASIVE (THAILAND) High Carbon Steel Shot & Grit

6

BLAST NOZZLES, NOZZLE-HOLDERS, HOSES AND HOSE COUPLINGS

SPEEDLOCK REMOTE CONTROL SYSTEM (Electric/Pneumatic Operated)

5. ELECTRIC /PNEUMATIC OPERATED REMOTE CONTROL PANEL

OPERATORS SAFETY EQUIPMENT

NOTE: All Airline Breathing Filters and Breathing Filter Cartridges DO NOT REMOVE Toxic Gases or Carbon Monoxide.

RPB Filter Cartridge

Both RPB and BULLARD Filter Cartridges are compatible and can be fitted onto most brands of Breathing Airline Filter.

ELECTRIC/PNEUMATIC REMOTE CONTROLADVANTAGES

For most permanent installation , such as on Blast Chamber facility or where blast hoses are long or are required to perform dual-functions, an Electric/Pneumatic Remote Control System is highly recommended.

DEADMAN SWITCH

Standard Switch

3-Positions Switch

- Ability to respond fast even over long distance (60m & over)

- Option to do Blast and Air Blown operation with same Blast Hose

- Option to do blasting operation at extreme height with minimum abrasive choking problem during Initial start period

- Blast Hour Meter can be incorporated at the Control Panel to determine individual Blasters Productivity and Machine Maintenance Schedule

RADEX AIRLINE FILTER SYSTEM FROM RPB LTD

RADEX offers more capacity, more versatility and more filtration. You can combine the versatility of either floor mount or wall mounting with increased filtration capacity.

RADEX meets breathing air requirements - Grade D, AS1715, EN 12021, ISO 8573.1 Class 1, 2 & 3.

RADEX Airline Filter System Bullard Filter Cartridge

8

SPEEDLOCK PRESSURE PAINT POTS & DIAPHRAGM PUMPS

11

E.S.C.S (UK) EQUIPMENT FOR PASSIVE FIRE PROOFING MATERIAL (DISTRIBUTOR)

E.S.C.S EQUIPMENT have been supplied world-wide and has become the market leader in application of solvent free PFP Epoxies

ESCS Pre-Mix Machine ES430 FR PFPCart-Mounted System

ES430 FR PFPSkid-Mounted System

ES430 FR PFP Skid-MountedSystem (Atex Certified)

BLAST CABINET

Suction Blast Principle Pressure Blast Principle

Small Unit Large Unit

ENCLOSED DECK/FLOOR SHOT BLASTING

ENCLOSED DUST-FREE BLASTING

DUST-FREE BLASTING SOLUTIONS

When requesting for quote, please specify the following: Blast Cabinet System - Suction or Pressure Blast Cabinet size required and type of abrasive used Applications - polishing, deburring, etching, etc

The above machine is without doubt the best method of Surface Preparation available at the present time. This method is quick, clean and fully self-contained, allowing Projects undertaken to be completed in minimum time without dust-pollution associated with abrasive blasting. This method is effective on both concrete and steel surfaces leaving cleaned profile surfaces for subsequence coatings to adhere to.

WET BLAST INJECTOR SYSTEM

Reducing dust-pollution by injecting fresh-water under pressure into the blast stream.

EDUCT-O-MATIC

Suitable for vacuum-blasting weld-seams and small surface areas.

VACUUM-PRESSURE BLAST SYSTEM

Suitable for vacuum-blasting weld-seams and larger surface areas.

INTERNAL TANK BLASTING & COATING EQUIPMENT

12

WATER-COOLED AFTER-COOLER AIR-COOLED AFTER-COOLER

FOR RECOVERING OR TRANSFERRING OF ABRASIVES

PORTABLE PNEUMATIC VACUUM MACHINE

Driven by 75kw, Class F & IP-55 Electric Motor.Powered by 3 Lobe Root BlowerCapacity: 8 ton/hr of Copper Slag

PORTABLE 8-TON SILO ACCESSORIES

Grit Hoses Vacuum-Hoses

Pick-Up Tool

TO ENSURE ENCLOSURES CONDITION IS BELOW 45% RELATIVE HUMIDITY

PORTABLE AIR-COOLED DEHUMIDIFIER

Capacity : Variable 10,000 to 12,000CMH @ 150mm wg

DUCTINGS

PVC x 100m / Roll Canvas x 24m / Length

TO REMOVE/REDUCE BLASTING CONTAMINANTS TO REMOVE PAINTING MIST & FUME

PORTABLE DUST COLLECTOR PORTABLE VENTILATING SYSTEM

Capacity : Range from 13,500 to 35,000CMH @ 200mm wgFilter Cartridge System Filter Cartridge Length : 914mm long Reverse Air-Pulsing using outside Compressed Air

Capacity : 7,000 to 12,000CMH @ 150mm wg 3,000 to 6,500CHM @ 75mm wgNote : Spark-Resistant Fan & Increased Safety Electric Motor

Portable & easily transportedby crane & fork-lift

Single Chamber Double Chamber

1800 cfm 6 Nozzles

2100 cfm 6 Nozzles

1800 cfm - 6 Nozzles 3600 cfm - 12 Nozzles 750 cfm 2 Nozzles

FOR REMOVING MOISTURE FROM COMPRESSED AIR SUPPLIES

Electrical Axial FanElectrical Centrifugal Fan Air Power Axial Fan

14

DST-SPEEDLOCK AIR-POWERED AIRLESS SPRAY PUMPS

DST-SPEEDLOCK Extreme Series Airless Pumps

TECHNICAL SPECIFICATIONS

Pump Model DP-30 DXT-45 DXT-56 DXT-68

Pump Pressure Ratio 30 : 1 45 : 1 56 : 1 68 : 1

Maximum Output Fluid Pressure

250 bar (3,625psi)

310 bar (4,500psi)

386 bar (5,600psi)

469 bar (6,800psi)

Flow Rate @ 60 Cycles per Minute

3.66 lpm 15.0 lpm 13.0 lpm 11.0 lpm

Input Air Pressure Range

2 ~ 8.4 bar (29 ~ 122 psi)

2 ~ 6.9 bar (29 ~ 100 psi)

2 ~ 6.9 bar (29 ~ 100 psi)

2 ~ 6.9 bar (29 ~ 100 psi)

Flow Rate/Cycle 60cc 250cc 220cc 180cc

Air Motor Diameter 150 mm 254 mm 254 mm 254 mm

Packed Dimension (54 x 57 x 88)

cm (73 x 78 x 147)

cm (73 x 78 x 147)

cm (73 x 78 x 147)

cm

Weight 28 kg 110 kg 110 kg 110 kg MODEL DP-30 MODEL DXT

SPEEDLOCK-DST Airless Spray Gun

4 FINGER AIRLESSGOLDEN GUNSWP : 7250 psi

CONFIGURATIONS

RAC Tip Guard

Standard Tip Guard

RAC Tip

Flat Tip

Tip Filter Housing

Tip Filter

Nozzle Swivel Gun Swivel

Gun Safety On

S-PLUS AIRLESS

SILVER GUNSWP : 5000 psi

#60 #80 #100

DST-SPEEDLOCK Airless Spray Hoses & Accessories

1-wire braided

Working Pressure Bursting Pressure

413 bar (6,000 psi) 1,280 bar (18,560 psi)

1-wire / 1-Textile 550 bar (7,975 psi) 1,650 bar (23,925 psi)

1-wire braided

Working Pressure Bursting Pressure

310 bar (4,500 psi) 930 bar (13,485 psi)

2-wire braided 450 bar (6,525 psi) 1,350 bar (19,575 psi)

Nipple 3/8 & Nipple 1/4Reducing Nipple 3/8 & 1/4

Airless Paint Hose 1/4 I.D.

Airless Paint Hose 3/8 I.D.

Air Hose 3/4 x 15mCoupled

SPEEDLOCK-DST Extreme Series Airless Pumps are all fitted with a newly developed lower assembly to cater for applications of modern protective coating systems used in the most demanding work environment; and it is designed for ease of operation and maintenance.

TITAN SPRAY EQUIPMENT & ACCESSORIES

18

LX-80 Airless Gun

ACCESSORIES

Textile Braided AirlessSpray Hose

SWP : 3300 psi

4-Finger Gun 2-Finger Gun

Flat Tip

LX-75 Pole Gun SC-6+ Tip

SC-6+ Tip Guard

PERFORMANCE 460e

Perfectly suited for residential, property maintenance and small commercial applications, the performance 460e applies all standard primers, paints and architectural coatings with ease.

PERFORMANCE 850e

Multiple gun unit, delivering performance and functionality! Sprays stains, lacquers, epoxies, latex, dry fall and block fillers.

ADVANTAGE GPX 130

The GPX 130 is a production sprayer capable of supporting large tips and multiple guns on big jobs. A powerful 6.0 HP Subaru petrol engine provides plenty of power for spraying most heavy architectural coatings, block fillers and epoxies.

POWRTWIN 12000 PLUS

For large scale industrial and commercial projects where maximum GPM output is the difference between profit and loss serious professionals turn to the PowrTwin 12000 Plus, a super workhorse that can feed any architectural primer or paint coating to as many as six guns.

POWRLINER 4950

Designed and built for contrac-tors who are serious about completing medium to large scale striping projects quickly and profitably. PowrLiner 4950 is the first step in hydraulic stripers where power and long-term, heavy duty operation are the difference between a business that makes money and one that does not.

PERFORMANCE 1150e

The performance 1150e is designed to be used everyday on all residential, industrial and commercial applications. This unit sprays all materials from stains, lacquer, enamel, latex, epoxies, block fillers and elastomerics.

27

ABRASIVES

SPEEDLOCK ALLOY ANGULAR STEEL GRIT AND LOW CARBON MIXED SHOTS

ALLOY ANGULAR STEEL GRIT is mainly used in compressed air pressure blasting operation and have the following advantages over HighCarbon Steel Grit due to its fully angular shape, more homogeneous hardness, higher density and better wear resistance (Nice Microstructure).The Hardness and Wear Resistance properties are due to its High Chromium and Carbon contents plus the unique manufacturing process and theraw-material used.

LOW CARBON STEEL SHOT is specially formulated for use in Auto-Blast Wheel Machine operation to improve blasting performance and has better wear-resistance than High Carbon Steel Shot. Due to lesser break-down of the Low Carbon Steel Shot, there will be less wear and tear on expensive Auto-Blast Machine components due to abrasion by fine steel dusts. The Hardness and Wear Resistance properties are due to its high Manganese content plus the unique manufacturing process and the raw-material used.

W ABRASIVE HIGH CARBON STEEL SHOT & GRIT (THAILAND)

W ABRASIVE Cast High Carbon Steel Grit primarily used for blast-cleaning of steel plates, beams, pipes, steel structures, castings, forgings,etc.; or in the pre-treatment of metal surfaces prior to finishing process.

Physical Properties and Chemical Composition of Steel Shot and GritIn accordance with Standards of ISO 11124-3 High Carbon Steel Shot and Grit, SFSA20-66 Cast Steel Abrasives, SAE J827 Cast Steel Shot, SAEJ1993 High Carbon Cast Steel Grit.

GP Angular when new, this grit rapidly round off in use and is suited for de-scaling applications. GL Although harder than GP Steel Grit, it also loses its sharp edges during blasting operations and is particularly suited for de-scaling and surface preparation applications GH Has the maximum hardness and remains in angular shape even after each blasting operation. It is suitable for surface treatment process that required uniform etched finishes. GH Steel Grit should be only use in auto-shot blast machine where working requirements take precedence over cost consideration (e.g. with roll mill cylinders or where a special surface finish is needed). For use in mainly with compressed pressure blast machines.

PACKING: 25kg/bag and 1000kg (40 bags/carton box) on one pallet

Chemical Composition(%)

Steel Shot GP Steel Grit GL Steel Grit GH Steel Grit

C 0.85 1.20

Mn. 0.60 1.20

Si. 0.40 1.20 S 0.05 max.

P 0.05 max. Hardness 40 50 HRC 42-50 HRC 56-60 HRC 63-66 HRC

Hardness Deviation Maximum deviation 3.0 HRC Microstructure Finely tempered Martensite

Minimum Density(displacement of

alcohol)

7.4g/CC

All Steel Grits and Shots are manufactured and screened to meet or exceed SAE Specifications

PHYSICAL PROPERTIES ALLOY ANGULAR - GRIT HIGH CARBON - GRIT LOW CARBON - SHOT HIGH CARBON - SHOT

Average Hardness > 60HRC > 60HRC 42 ~ 48HRC 40 ~ 50HRC

Shape Fully Angular Arc Angular Spherical Spherical

Microstructure Tempered Martensite Tempered Martensite Duplex Structure - Mixture Tempered Martensite

and Fine Carbide Coarse & Netty Carbide of Bainite & Martensite Coarse & Netty Carbide

Density (alcohol displacement) 7.5g/cm3 7.3g/cm3 7.2g/cm3 7.3g/cm3

Raw Material Forged Bearing Steel offcuts All kinds of Steel Scrap Low Carbon Steel Scrap All kinds of Steel Scrap

CHEMICAL COMPOSITION ALLOY ANGULAR GRIT HIGH CARBON - GRIT LOW CARBON - SHOT HIGH CARBON SHOT

Carbon 0.85 ~ 1.20% 0.85 ~ 1.20% 0.10 ~ 0.20% 0.85 ~ 1.20%

Manganese 0.60 ~ 1.20% 0.60 ~ 1.20% 0.35 ~ 1.50% 0.60 ~ 1.20%

Silicon 0.40 ~ 1.20% 0.40 ~ 1.20% 0.10 ~ 0.35% 0.40 ~ 1.20%

Sulphur < 0.05% < 0.05% < 0.05% < 0.05%

Phosphorus < 0.05% < 0.05% < 0.05% < 0.05%

Chromium 0.60 ~ 1.60% 0% N.A. N.A.

COMPARISON CHART

PACKING: 25kg/bag and 1000kg (40 bags/carton box) on one pallet

01020304050607080910111213141516171819202122232425262728