Lecture 2 SLOPE DEFLECTION
-
Upload
laila-azreen -
Category
Documents
-
view
772 -
download
77
description
Transcript of Lecture 2 SLOPE DEFLECTION
2005 Pearson Education South Asia Pte Ltd 1
STRUCTURAL ANALYSIS VBB 2053
LECTURE 2
SLOPE-DEFLECTION METHOD
2005 Pearson Education South Asia Pte Ltd 2
Learning Objectives Learn to analyse statically indeterminate
structures using slope-deflection method. Knowing the slope-deflection equations. Discuss the application of slope-deflection
method to beams and frames.
2005 Pearson Education South Asia Pte Ltd 3
Outline Introduction to slope-deflection method. General procedure of slope-deflection method
of analysis. Derivation of slope-deflection equations. Work examples on slope-deflection method of
analysis: beams and frames.
2005 Pearson Education South Asia Pte Ltd 4
Statically Indeterminate Structures: Method of Analysis Analyzing any indeterminate structure, it is
necessary to satisfy: Equilibrium – Equilibrium is satisfied when the
reactive forces hold the structure at rest. Compatibility – Compatibility is satisfied when the
various segments of the structure fit together without intentional breaks or overlaps.
Force-displacement – This requirements depend upon the way the material responds – linear elastic response.
2005 Pearson Education South Asia Pte Ltd 5
Statically Indeterminate Structures: Method of Analysis There are two ways to analyze a statically
indeterminate structure Force Method Displacement Method
2005 Pearson Education South Asia Pte Ltd
Force Method of Analysis Identifying unknown redundant forces. Satisfying structure’s compatibility equations. This is done by expressing the displacements
in terms of the loads by using the load-displacement relations.
The solution of the resultant equations yields the redundant reactions, and then the equilibrium equations are used to determine the remaining reactions on the structure.
6
2005 Pearson Education South Asia Pte Ltd
Displacement Method of Analysis Satisfying equilibrium equations for the
structure. Unknown displacements are written in terms
of the loads by using the load-displacement relations, then solved for the displacements.
Once the displacement obtained, the unknown loads are determined from the compatibility equations using the load-displacement relations.
7
2005 Pearson Education South Asia Pte Ltd
Degree of Freedom When a structure is loaded, the node will
undergo unknown displacements. These displacements are referred to as the
“degree of freedom”. Specify degree of freedom is a necessary 1st step when apply displacement method.
In 3D, each node on a beam or frame can have at most 3 linear displacements & 3 rotational displacements.
In 2D, each node can have at most 2 linear displacements & 1 rotational displacement.
8
2005 Pearson Education South Asia Pte Ltd
Degree of Freedom The number of these unknowns are referred
to as the degree in which the structure is kinematically indeterminate.
9
Any load applied to the beam will cause node A to rotate.
Node B is completely restricted from moving.
Hence, the beam has only one unknown degree of freedom.
Therefore kinematically indeterminate to 1st degree.
2005 Pearson Education South Asia Pte Ltd
Degree of Freedom
10
The beam has nodes at A, B & C
There are 4 degrees of freedom A, B, C and C.
It is kinematically indeterminate to 4th degree.
The frame has 3 degrees of freedom, B, C and B.
It is kinematically indeterminate to 3rd degree.
2005 Pearson Education South Asia Pte Ltd 11
Slope-Deflection Method The slope-deflection method uses displacements as
unknowns and is referred to as a displacement method.
In the slope-deflection method, the moments at the ends of the members are expressed in terms of displacements and end rotations of these ends.
An important characteristic of the slope-deflection method is that it does not become increasingly complicated to apply as the number of unknowns in the problem increases.
In the slope-deflection method the individual equations are relatively easy to construct regardless of the number of unknowns.
2005 Pearson Education South Asia Pte Ltd
Derivation of Slope-Deflection Equations To derive the general form of the slope-deflection
equation, let us consider the typical span AB of the continuous beam shown below when subjected to arbitrary loading.
The slope-deflection equation can be obtained using the principle of superposition
By considering separately the moments developed at each support due to θA, θB, Δ, P.
Assume clockwise is positive.
2005 Pearson Education South Asia Pte Ltd 13
Derivation of Slope-Deflection Equations Moment due to angular displacement at A, θA
To determine the moment MAB needed to cause this displacement, we will use the conjugate beam method.
From which we obtain the following relationships.
AAB L
EI4M ABA L
EI2M
03
L2L
EI
M
2
1
3
LL
EI
M
2
1
0M
BAAB
'A
0L3
L2L
EI
M
2
1
3
LL
EI
M
2
1
0M
AABBA
'B
2005 Pearson Education South Asia Pte Ltd 14
Derivation of Slope-Deflection Equations Moment due to angular displacement at B, θB
The applied moment MBA to the angular displacement B & the reaction moment MAB at the wall can be related as:
BBA L
EI4M BAB L
EI2M
2005 Pearson Education South Asia Pte Ltd
Derivation of Slope-Deflection Equations Moment due to relative linear displacement, Δ If the far node B of the member is displaced relative to A, so that
the cord of the member rotates clockwise & yet both ends do not rotate, then equal but opposite moment and shear reactions are developed in the member.
Moment M can be related to the displacement using conjugate beam method.
15
2BAAB
'B
L
EI6MMM
03
LL
EI
M
2
1
3
L2L
EI
M
2
1
0M
2005 Pearson Education South Asia Pte Ltd
Derivation of Slope-Deflection Equations Moment due to loading (P or w) These moments are called Fixed End Moment (FEM). In general, linear and angular displacement of the nodes are
caused by loadings acting on the span of the member. To develop the slope-deflection equation, we must transform
these span loadings into equivalent moment acting at the nodes and then use the load-displacement relationships just derived.
16
2005 Pearson Education South Asia Pte Ltd 17
2005 Pearson Education South Asia Pte Ltd
Derivation of Slope-Deflection Equations Slope-Deflection Equation The end moments due to each displacement and loadings are
added together, the resultant moments at the ends can be written as:
MAB = MθA + MθB + MΔ + Mload
18
0FEMLΔ
3θ2θL
2EM
0FEMLΔ
3θ2θL
2EM
BAABBA
ABBAAB
I
I
2005 Pearson Education South Asia Pte Ltd
Derivation of Slope-Deflection Equations Slope-Deflection Equation The slope-deflection equations can be generalized as follows:
MN = internal moment in the near end of the span, E = modulus of elasticity k = span stiffness, k = I/L N, F = near- and far-end slopes or angular displacements of the span
at the supports = span rotation of its cord due to a linear displacement,
= /L FEMN = fixed end moment at the near end support.
19
NFNN FEMψ3θθ2Ek2M
2005 Pearson Education South Asia Pte Ltd 20
Slope-Deflection Equation Pin supported end span Sometimes an end span of a
beam or frame is supported by a pin or roller at its far end.
The moment at the roller or pin is zero provided the angular displacement at this support does not have to be determined.
Use the generalised slope-deflection equation, we have:
Since far end is pinned, FEMF = 0
FEMN can be obtained
0ψ3θθ2Ek20
FEMψ3θθ2Ek2M
FN
NFNN
2005 Pearson Education South Asia Pte Ltd 21
Slope-Deflection Equation Simplifying, we get:
Only applicable for end span with far end pinned or roller supported
NNN FEMψθEk3M
2005 Pearson Education South Asia Pte Ltd
Work Example 1 Draw the shear & moment diagrams for the
beam shown below.
22
2005 Pearson Education South Asia Pte Ltd
Work Example 2 Draw the shear & moment diagrams for the
beam shown below.
23
A
B
C
40 kN/m 60 kN
6 m1 m 1 m
2005 Pearson Education South Asia Pte Ltd 24
Analysis of Frames: No Sidesway Slope-deflection method can also be used to analyse
frames. A frame will not sidesway to the left or right provided it
is properly restrained.
2005 Pearson Education South Asia Pte Ltd 25
Analysis of Frames: No Sidesway No sidesway will occur in an unrestrained frame
provided it is symmetric with respect to both loading and geometry.
2005 Pearson Education South Asia Pte Ltd 26
Work Example 6: Frame With No Sidesway Determine the moments at each joint of the
frame shown below. EI is constant. 3 spans must be considered in this
case: AB, BC & CD
Step 1: FEM
m.kN8096
wL5FEM
m.kN8096
wL5FEM
2
CB
2
BC
0ψψψ and 0θ θ that Note CDBCABDA
2005 Pearson Education South Asia Pte Ltd 27
Work Example 6: Frame With No Sidesway Step 2: Slope-Deflection Equations
CDC
CCD
BCCB
CBBC
BBA
BAB
θEI1667.0M
θEI333.0M
80θEI25.0θEI5.0M
80θEI25.0θEI5.0M
θEI333.0M
θEI1667.0M
NFNN FEMψ3θθ2L
IE2M
2005 Pearson Education South Asia Pte Ltd 28
Work Example 6: Frame With No Sidesway Step 3: Equilibrium Equations
Moment equilibrium at joints B & C, we have:
Substitute MBA, MBC and MCB, MCD into above equations, we get:
Solving simultaneously yields
80θEI25.0θEI833.0
80θEI25.0θEI833.0
BC
CB
0MM ;0M BCBAB 0MM ;0M CDCBC
EI
1.137θθ CB
2005 Pearson Education South Asia Pte Ltd 29
Work Example 6: Frame With No Sidesway Step 4: Moment Calculation
Using these results, the reactions at the ends of each member can be determined
using equations of equilibrium. The moment diagram for the frame can
be drawn.
kNm9.22M
kNm7.45M
kNm7.45M
kNm7.45M
kNm7.45M
kNm9.22M
DC
CD
CB
BC
BA
AB
2005 Pearson Education South Asia Pte Ltd
Work Example 7: Frame With No Sidesway
Determine the internal moments at each joint of the frame shown below. The moment of inertia for each member is given in the figure. Take E = 200 Gpa.
Take as self study at home….Refer to Hibbeler 7th edition, Example 11-6
30
4.5 m
30 kN 50 kN/m
A
B C E
D
2.4 m 2.4 m
3.6 m320 (106) mm4
260 (106) mm4
160
(106 )
mm
4
80 (106) mm4
2005 Pearson Education South Asia Pte Ltd 31
Analysis of Frames: Sidesway A frame will sidesway when it or the loading acting on
it is nonsymmetric. Consider the frame shown here.
The loading P causes an unequal moments at joint B and C.
MBC tends to displace joint B to the right.
MCB tends to displace joint C to the left.
Since MBC > MCB, the net result is a sidesway of both joint B & C to the right.
2005 Pearson Education South Asia Pte Ltd 32
Analysis of Frames: Sidesway When applying the slope-deflection equation to each
column, we must consider the column rotation ( = /L) as an unknown in the equation.
As a result, an extra equilibrium equation must be included in the solution.
The techniques for solving problems for frames with sidesway is best illustrated by work examples.
2005 Pearson Education South Asia Pte Ltd 33
Work Example 8: Frame With Sidesway Determine the moments at each joint of the
frames shown below. Ends A & D are fixed. Sidesway occurs here. AB = /4 (+ ve)
DC = /6 (+ ve)
AB = (6/4)DC
2005 Pearson Education South Asia Pte Ltd 34
Work Example 8: Frame With Sidesway Slope-Deflection Equations
(6) )ψ0.1θ333.0(EIM
(5) )ψ0.1θ667.0(EIM
(4) )θ4.0θ8.0(EIM
(3) )θ4.0θ8.0(EIM
(2) )ψ25.2θ0.1(EIM
(1) )ψ25.2θ5.0(EIM
DCCDC
DCCCD
BCCB
CBBC
DCCBA
DCBAB
2005 Pearson Education South Asia Pte Ltd 35
Work Example 8: Frame With Sidesway Equilibrium Equation
9 unknowns and 6 equations. Thus, we need 3 equilibrium equations.
2 moment equilibrium equations for joints B & C.
Another equilibrium equation obtained from summation of forces (entire frame) in x-direction, since there is horizontal displacement .
(7) 0MM ;0M BCBAB (8) 0MM ;0M CDCBC
(9) 0VV200 ;0F DAX
2005 Pearson Education South Asia Pte Ltd 36
Work Example 8: Frame With Sidesway Equilibrium Equation
Considering the free-body diagram of each column separately.
(9) 06
MM
4
MM200
6
MMV0M
4
MMV0M
CDDCBAAB
CDDCDC
BAABAB
2005 Pearson Education South Asia Pte Ltd 37
Work Example 8: Frame With Sidesway Equilibrium Equation
Substitute equation (2) and (3) into equation (7). Substitute equation (4) and (5) into equation (8). Equation (1), (2), (5) and (6) into equation (9).
Solve simultaneously, we have
48.208ψEI
66.75θEI
78.243θEI
DC
C
B
2005 Pearson Education South Asia Pte Ltd 38
Work Example 8: Frame With Sidesway Moment calculation
Using these results & solving for equation (1) to (6)
kNm183M
kNm158M
kNm158M
kNm225M
kNm225M
kNm347M
DC
CD
CB
BC
BA
AB