Layer 3 Message Analysis.ppt
-
Upload
mahmudah-zyzy -
Category
Documents
-
view
181 -
download
1
description
Transcript of Layer 3 Message Analysis.ppt
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
Content
Layer3 Message Analysis
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
AMR CS Call Phases
BTS
1. Cell search, BCCH decoding & RACH access
DRNC SRNC CNUE
2. RRC Connection Setup
3. UE <-> CS-CN signalling
4. RAB Set-up
5. UE <-> CS-CN signalling
6. Service Established
7. Branch addition/deletion & active set update
8. Service Released
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
RRC Connection Set-up Signalling Flow
UE RNCWBTS
Admission Control
RRC: RRC CONNECTION REQUEST (RACH)
NBAP: RADIO LINK SETUP REQUEST
NBAP: RADIO LINK SETUP RESPONSE
RRC: RRC CONNECTION SETUP (FACH)
L1 Sync
NBAP: SYNCH INDICATION
RRC: CONNECTION SETUP COMPLETE (DCH)
ALCAP: ERQ
ALCAP: ECF
FP Downlink Sync
FP Uplink Sync
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
UE<–> CS_CN signalling
5. Call Setup4. Paging
1. Location Update Request
2. Authentication and Security Mode Setup
UE
WBTS
RNC MGW
MSC / VLR
3. Location Update Accept
•Location Update•Authentication•Security Mode Setup•Paging •Call Setup
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
PS Call Phase
BTS
1. Cell search, BCCH decoding & RACH access
DRNC SRNC CNUE
2. RRC Connection Setup
3. GPRS Attach
4. RAB Set-up
5. UE <-> PS-CN signalling (PDP context activation Accept)
7. PS Data Session Established
9. Branch addition/deletion & active set update
10. PS Data Session Released
6. Radio Bearer Reconfiguration
8. State Transitions
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
GPRS Attach
Direct Transfer: Attach Accept
Uplink Direct Transfer: Identity Response (DCH)
Direct Transfer: Identity RequestDownlink Direct Transfer: Common ID (DCH)
UE RNC SGSNNode B
Secuirty Mode Complete (DCH)
Security Mode CommandSecurity Mode Command (DCH)
Uplink Direct Transfer: Authenication and Ciphering Response (DCH) Direct Transfer: Authentication and Ciphering Response
Direct Transfer: Authentication and Ciphering RequestDownlink Direct Transfer: Authentication and Ciphering Request (DCH)
SCCP: Connection Confirm
Initial Direct Transfer: GPRS Attach Request (DCH)
Initial UE message : GPRS Attach RequestSCCP: Connection Request
Common ID
Direct Transfer: Identity Response
Downlink Direct Transfer: Location Attach Accept (DCH)
Direct Transfer: Attach CompleteUplink Direct Transfer: Attach Complete (DCH)
RRC Connection
• UE performs cell search and RRC Connection Establishment in the same way as for an AMR call
• The UE registers with the PS-CN through the GPRS Attach procedure
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
PDP Context
UE RNC SGSNNode B
Uplink Direct Transfer : Activate PDP context request (DCH) Direct Transfer : Activate PDP context request
RANAP: RAB Assignment RequestRRC: Radio Bearer Setup
Radio Bearer Setup Complete
RAB Assignment Response
Direct Transfer: Activate PDP Context AcceptDownlink Direct Transfer : Activate PDP Context Accept (DCH)
Call Established
Measurement Control
Measurement Control
GPRS Attach
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
Radio Bearer Setup/Complete & RAB Assignment Response
• Once the RANAP: RAB Assignment Request message has been received from PS CN and RNC has resources to setup the 0/0 kbps RB the RNC sends a RRC: Radio Bearer Setup message to the UE
• The UE acknowledges the RRC: Radio Bearer Setup message with a RRC: Radio Bearer Setup Complete message
• Once the radio bearer establishment has been acknowledged, the RNC indicates to the PS core that the RAB has been established using the RANAP: RAB Assignment Response message
UE RNC SGSNNode B
Uplink Direct Transfer : Activate PDP context request (DCH) Direct Transfer : Activate PDP context request
RANAP: RAB Assignment RequestRRC: Radio Bearer Setup
Radio Bearer Setup Complete
RAB Assignment Response
GPRS Attach
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
Radio Bearer Reconfiguration
AAL2SIG:ECFAAL2SIG:ERQ
Radio Link Reconfigure Ready
UE RNC SGSNNode B
NBAP: Radio Link Reconfigure Prepare
Uplink Direct Transfer : Activate PDP context request (DCH) Direct Transfer : Activate PDP context request
RANAP: RAB Assignment RequestRRC: Radio Bearer Setup
Radio Bearer Setup Complete
RAB Assignment Response
Direct Transfer: Activate PDP Context AcceptDownlink Direct Transfer : Activate PDP Context Accept (DCH)
Call Established
Measurement Control
Measurement Control
Measurement Report : e4a
FP: Downlink Sync
FP: Uplink SyncRadio Link Reconfiguration Commit
RRC: Radio Bearer Reconfiguration (DCH)RRC: Radio Bearer Reconfiguration Complete (DCH)
Measurement Control
GPRS Attach
Admission Control
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
HSPA Setup
• HSUPA cannot be established without HSDPA, HSDPA UL return channel is HSUPA instead of R99
• High level procedure is the same as that for an NRT DCH• RNC starts by allocation a 0/0kbps connection• Selection between DCH and E-DCH is then completed when RNC receives the uplink or
downlink capacity request
HSUPA connection can be established• RRC Idle mode
• directly from CELL_PCH (Cell Update with reason Uplink Capacity Request)
UE RNC SGSNNode B
RRC Establishment
GPRS Attach
RNC completes channel type selection
procedure
PDP Context Activation
Measurement Report : e4a
0/0 kbps DCH
allocated
Uplink capacity request
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
RRC Services
• Broadcast services• Paging and Notification services• Dedicated Control services• Encapsulation of NAS signaling (CC, SM, MM, GMM, SMS)
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
RRC States
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
RRC Procedure
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information
• Within UTRAN system information is broadcasted with the help of the RRC messages•System Information,•Paging Type I, and•System Information Change Indication.
• Most system information parameters are determined by the RNC. The Node B is informed about the parameters via the NBAP message BCCH Information. Some system parameters can be made available by the Node B, such as interference values, which change fast.
• Given the system information, the UE is capable to decide, whether or how to access the PLMN via the existing cell. • System information is organised in System Information Blocks (SIBs).
•System information is grouped into SIB 1 to SIB 18.•Each SIB is responsible to carry a specific content. For instance, SIB 12 holds measurement control information and parameters.•Depending on the UE‘s RRC state, is reads specific SIBs, and uses the transmitted parameters.
• There is a huge amount of SIBs, which have to be read by the UE. This requires a lot of battery power. Therefore, a Master Information Block (MIB) was introduced, which gives references and scheduling information about the SIBs. The MIB is transmitted in every 8th radio frame on the P-CCPCH (on position SFN mod 8 = 0, and with a TTI of 20 ms). For most of the SIBs used within the system, the MIB may carry a value tag. The only exceptions are SIB 15.2, SIB 15.3 and SIB 16. If a value tag is unchanged, the corresponding system information has not been modified. Thus, there is no need for the UE to read the SIB. SIB 7 has no value tag. It changes with each occurrence. Scheduling information is used to inform the UE, where and when a specific system information is transmitted.
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information
Node B
UTRANSystem Information ( )
UE RNC
NBAP: BCCH Information
MIBvalue tag M
SIB 1value tag 1
SIB 2value tag 2
SIB 3value tag 3
SIB 18value tag 18
position on P-CCPCH: SFN mod 8* = 0TTI: 20 ms
value tag M: range 1..8SB
value tag N
TS 25.433: NBAP8.2.16 System Information Update
TS 25.433: NBAP8.2.16 System Information Update
MIB: Master Information BlockSIB: System Information BlockSFN: System Frame Number
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information Blocks• For each SIB, following characteristics were specified:
•Area scope: Where is the value tag valid: within one cell or within a PLMN/ equivalent PLMN?•UE RRC state: When the SIB is valid?•UE RRC state: When the SIB is read?•Scheduling information: At which position is the SIB transmitted and what is its repetition period?•Modification of system information: Is it indicated by a value tag, or is it timer based?
• The UE receives all SIBs via the BCCH. There is only one exception: SIB 10. If a UE is capable to receive simultaneously on one S-CCPCH and on one DPCH, then it receives SIB 10 on a FACH.
• Master Information Block (MIB):•The MIB informs the UE about the supported PLMN types and the PLMN identity.•The UE finds in the MIB also references to up to maxSIB (=32) SIBs, including their scheduling information and type. •A MIB is valid in one cell. If a UE changes the cell, is must read the new cell‘s MIB.•The MIB is read in the RRC modes/states RRC idle, CELL_FACH, CELL_PCH and URA PCH.•Its parameter are valid in the same states. •A change of the MIB information is indicated by a value tag.
• In this course documentation, we only describe the System Information Blocks (SIBs), which are used in NSN‘s RAN, and SIB 4 and SIB16.
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information Blocks
• System Information Block 1 (SIB 1)•This SIB is used to inform the UE about NAS system information.•The NAS system information characterises the NAS domains.•SIB 1 also delivers UE timers and counters, which have to be used by the UE in the RRC idle and RRC connected mode.
•For instance, a UE in the RRC connected mode uses the timer T305 for periodic cell and URA updates. •SIB 1 is valid in one PLMN.• The MIB is read in the RRC modes/states RRC idle, CELL_FACH, CELL_PCH and URA PCH. Its parameter are valid in the same states, and the the RRC sub-state CELL_DCH.•If the UE selects a new cell, and the SIB 1 value tag has the same number as in the preceding cell, the same content is transmitted in this SIB. There is then no necessity for the UE to read this SIB after cell re-selection.
• System Information Block 2 (SIB 2)•This SIB contains an URA identity list. •SIB 2 is read and valid in the RRC sub-state URA_PCH. A change of the SIB 2 information is indicated by a value tag.
• System Information Block 3 (SIB 3)•This SIB contains relevant parameters for cell selection and re-selection.•It also holds the cell identity and cell restriction data, such as „cell barred“ IEs. •SIB 3 must be read and is valid in the RRC idle mode. It is read and valid in the RRC connected mode sub-states CELL_FACH, CELL_PCH and URA_PCH, if SIB 4 is not broadcasted. •A change of the SIB 3 information is indicated by a value tag.
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information Blocks
• System Information Block 4 (SIB 4)•This SIB holds mostly the same data fields as SIB 3*, but it is read and valid only, when the UE is in the RRC connected mode. I.e, this optional SIB is read and valid in the CELL_FACH, CELL_PACH and URA_PCH sub-state.• A change of the SIB 4 information is indicated by a value tag.
• System Information Block 5 (SIB 5)•The parameters for the configuration of physical channels are broadcasted in this SIB.•The parameters cover the PICH power offset, the AICH power offset, P-CCPCH, S-CCPCH and PRACH system information lists.•SIB 5 must be read and is valid in the RRC idle mode.•It is read and valid in the RRC connected mode sub-states CELL_FACH, CELL_PCH and URA_PCH, if SIB 6 is not available.•A change of the SIB 5 information is indicated by a value tag.
• System Information Block 7 (SIB 7)•This SIB holds fast changing parameters. Therefore no value tag is used for it.•The UE has to read its parameters periodically.
•For that, an expiration timer (Expiration Time Factor) is broadcasted with this message.•SIB 7 expires at max(32, 8 * Expiration Time Factor).•Expiration Time Factor can have the values 2times, 4 times, 8 times ... 256 times. Its default value is 1.
•The fast changing parameters transmitted with SIB 7 include the UL interference and dynamic persistence level.•It is read and valid in all states except for the CELL_DCH sub-state.
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information
SIB broadcasted information readscope/
modification
MIB • PLMN types & identities#
• SIB Scheduling information• SIB references
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH
cell/value tag
valid
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH
SIB 1 • NAS information• UE timers & counters
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH
PLMN/value tag
RRC idle mode,CELL_DCH, CELL_FACH,
CELL_PCH, URA_PCH
SIB 2 • URA identity list URA_PCH cell/value tag
URA_PCH
SIB 4* • Cell selection & re-selection parameters for
UEs in the connected mode
CELL_FACH, CELL_PCH, URA_PCH
cell/value tag
CELL_FACH, CELL_PCH, URA_PCH
SIB 3* • Cell selection and re-selection parameters°
RRC idle mode,(CELL_FACH, CELL_PCH,
URA_PCH)
cell/value tag
RRC idle mode,(CELL_FACH, CELL_PCH,
URA_PCH)
SIB 5* • Parameters for common physical channel
configuration
RRC idle mode,(CELL_FACH,
CELL_PCH, URA_PCH)
cell/value tag
RRC idle mode,(CELL_FACH,
CELL_PCH, URA_PCH)
* Read SIB 3 / 5 in Connected Mode if SIB4 / 6 (Connected Mode) not available
# GSM-MAP/ANSI41; MCC+MNC; ° + Cell Access Restrictions
e.g. T305: Periodic Cell/URA UpdateT301, 302, 304, 307-317
e.g. CPICH Ec/N0 or CPICH RSCP; Sintrasearch, Sintersearch, Ssearch,RAT, Qqualmin, Qrxlevmin,..
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information Blocks• System Information Block 11 (SIB 11)
•This SIB holds measurement control information.•The UE gets here the relevant date for traffic measurement, intra-frequency measurements, etc.•SIB 11 must be read and is valid in the RRC idle mode. It is read and valid in the RRC connected mode sub-states CELL_FACH, CELL_PCH and URA_PCH, if SIB 12 is not broadcasted.•It is also valid in the RRC sub-state CELL_DCH, as long as the UE did not get a Measurement Control message from UTRAN and SIB 12 is not broadcasted.•A change of the SIB 11 information is indicated by a value tag.
• System Information Block 12 (SIB 12)•SIB 12 transmits measurement control information for UEs in the RRC connected mode.•If not transmitted, the UEs take the parameters broadcasted with SIB 11.•If available, SIB 12 is read and valid in the RRC connected mode sub-states CELL_FACH, CELL_PCH and URA_PCH.•It is also valid in the RRC sub-state CELL_DCH, as long as the UE did not get a Measurement Control message from UTRAN. A change of the SIB 12 information is indicated by a value tag.
• System Information Block 16 (SIB 16)•RB, TrCH, and PhyCH parameters are broadcasted, which are stored by the UE both in the RRC idle and RRC connected mode.•The parameters are used during a handover to UTRAN. Consequently, these parameters stay valid, when the UE is connected to GSM and GPRS. •This SIB is valid in all RRC states, and read in all RRC states except for the CELL_DCH. The UE reads and stores the parameters. A change of the SIB 16 information is indicated by a value tag.
Copyright © All rights reserved TA -TC 6250 E01TECHCOM Consulting
System Information Blocks
SIB broadcasted information readscope/
modification
SIB 7 Fast changing parameters: • UL interference level
• Dynamic persistence level
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH
cell/ max(32, 8 * Expir-‘ation Time Factor)
valid
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH
SIB 11 Measurement control information*
RRC idle mode,(CELL_FACH, CELL_PCH,
URA_PCH)
cell/value tag
RRC idle mode,(CELL_DCH, CELL_FACH,
CELL_PCH, URA_PCH)
SIB 12 • Measurement control information* for UEs in the
RRC connected mode
CELL_FACH, CELL_PCH, URA_PCH
cell/value tag
CELL_DCH, CELL_FACH, CELL_PCH, URA_PCH
SIB 16 • RB, TrCH, and PhyCH parameters for a
GSM/GPRS-UMTS HO
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH
cell/value tag
RRC idle mode,CELL_FACH, CELL_PCH,
URA_PCH)
(adopted from TS 25.331 RRC)
* e.g. FMCx & HOPx par.; Use of HCS; Ec/N0 orRSCP; Intra-, Inter-Frequency, Inter-RAT meas.
info; Traffic volume meas. Info (e.g. RLC buffer payload)
Examples of other SIB’s:SIB 13: ANSI-41 system informationSIB 14: Only for 3.84 Mcps TDD
SIB 15: useful for UE-based or UE-assisted positioning methods SIB 17: only for TDD
SIB 18: contains PLMN identities of neighbouring cells to be considered
in idle mode as well as in connected mode.