L35_inst
1
Installation Instructions Version 07-2009 T 604 708 1184 mplighting.com Copyright © MP Lighting All technical information in this document is subject to change. • Read all instructions. • WARNING: RISK OF FIRE OR ELECTRICAL SHOCK: Do not make or alter any openings in the compartment of wiring or electrical components during installation. Do not alter or add ballasts, or any other electrical components. • Installation and use of this fixture mounting assembly requires a person familiar with the construction and operation of luminaire electrical systems and the hazards involved, if not qualified, do not attempt installation. • Turn off power before installation. • Do not over tighten screws. • Do not spray water on fixture during cleaning. Avoid using detergents with hand softeners, anti-bacterial agents, glass cleaners or acrylic cleaning products. • KEEP THESE INSTALLATION INSTRUCTIONS. CAUTION LED 54mm 2-1/8” 102mm 4” Parts Qty. • LED unit w/ gasket • Cross countersunk screws • Teflon screw gaskets • LED driver 3W 350mA • Waterproof wire nuts 1 2 2 1 2 Tools • Phillips screwdriver not included Maintenance Use a soft cloth to remove any fingerprints. and clean acrylic lens. 1 2 Align cover plate to electrical box. 3 Tighten screws. 83mm 3-1/4” Remote Driver Option Connect fixture wires directly to low voltage box leads. LED3W350 AC Input Voltage: 100~240V, 50/60Hz DC Output Current: 350mA Constant Connect primary to driver input wires then fit into electrical box. • For cast in concrete use appropriate box rated for cast in concrete. Consult local electrical code. Cover Plate Teflon Gaskets Gasket Waterproof Wire Nuts LED35
-
Upload
mp-lighting -
Category
Documents
-
view
212 -
download
0
description
http://www.mplighting.com/pdf/installation/L/L35_inst.pdf
Transcript of L35_inst
InstallationInstructions
Version 07-2009
T 604 708 1184 mplighting.com
Copyright ©
MP
Lighting All technical inform
ation in this document is subject to change.
•Readallinstructions.
•WARNING:RISKOFFIREORELECTRICALSHOCK:Donotmakeoralteranyopeningsinthecompartmentofwiringorelectricalcomponentsduringinstallation.Donotalteroraddballasts,oranyotherelectricalcomponents.
•Installationanduseofthisfixturemountingassemblyrequiresapersonfamiliarwiththeconstructionandoperationofluminaireelectricalsystemsandthehazardsinvolved,ifnotqualified,donotattemptinstallation.
•Turnoffpowerbeforeinstallation.
•Donotovertightenscrews.
•Donotspraywateronfixtureduringcleaning.Avoidusingdetergentswithhandsofteners,anti-bacterialagents,glasscleanersoracryliccleaningproducts.
•KEEPTHESEINSTALLATIONINSTRUCTIONS.
CAUTION
LED
54mm
2-1/8”
102mm4”
83mm3-1/4”
Parts Qty.
• LED unit w/ gasket• Cross countersunk screws• Teflon screw gaskets • LED driver 3W 350mA• Waterproof wire nuts
12212
Tools• Phillips screwdriver not included
MaintenanceUse a soft cloth to remove any fingerprints. and clean acrylic lens.
12 Align cover plate
to electrical box.
3 Tighten screws. 54mm
2-1/8”
102mm4”
83mm3-1/4”
Remote Driver OptionConnect fixture wires directly to low voltage box leads.
LED3W350AC Input Voltage:100~240V,50/60Hz
DC Output Current:350mAConstant
Connect primary to driver input wires then fit into electrical box.
• For cast in concrete use appropriate box rated for cast in concrete. Consult local electrical code.
Cover Plate
TeflonGaskets
GasketWaterproof Wire Nuts
LED35
