L-BV5 Vacuum Pump Data Sheet
Transcript of L-BV5 Vacuum Pump Data Sheet
Data sheet liquidring pumpSeries L-BV5 | L_300 Range 2BV5 131 Compressor
Performance curves for compressor operation
500 m/h 450 16.2 kW Suction capacity V 400 60 Hz 50 Hz
350
13.5 kW
300
250 1000 1200 1400 Discharge pressure p2 1600 1800 mbar abs.
20 kW 15 60 Hz 50 Hz 16.2 kW 13.5 kW Power requirement P on the pump shaft 10
5
0 1000 1200 1400 Discharge pressure p2 1600 1800 mbar abs.
The characteristics are valid for the inlet of air with a relative humidity of 50 % and a temperature of 20 C at a atmospheric pressure of 1013 mbar abs. and water at 15 C as operating liquid. The tolerance is 10 %.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Compressors with ATEX 94/9 EG for category 2G are available, too.
Gardner Denver Deutschland GmbH
1
Techn. data sheet 2V5 131, edition 06/2005 En
Selection and ordering dataMaterialsCasing/port plate/impeller Frequency Hz voltage V
Motor dataRated current A output kW
Order-No.
Quantity of operating liquid
Sound pressure level **
Weight approx.
m/h
d(A)
kg
3~ 50/60 Hz version, protection class IP 55, insulation class F * cast iron/cast iron/bronze cast iron/cast iron/bronze cast iron/cast iron/bronze CrNi steel/CrNi steel/CrNi steel CrNi steel/CrNi steel/CrNi steel CrNi steel/CrNi steel/CrNi steel 50 60 50 60 50 60 50 60 50 60 50 60 200...240 220...275 345...415 380...480 500 575 200...240 220...275 345...415 380...480 500 575 345Y...415Y 380Y...480Y 345Y...415Y 380Y...480Y 60.0 60.0 35.0 35.0 23.0 23.5 60.0 60.0 35.0 35.0 23.0 23.5 35.0 35.0 35.0 35.0 13.5 16.5 13.5 16.5 13.5 16.5 13.5 16.5 13.5 16.5 13.5 16.5 2BV5131-8KH01-8S 2BV5131-8KH01-7S 2BV5131-8KH01-5S 2BV5131-8HH01-8S 2BV5131-8HH01-7S 2BV5131-8HH01-5S 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 76 78 76 78 76 78 76 78 76 78 76 78 185 185 185 185 185 185
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 and temperature class F. For the three phase machines the tolerances are 10 % for fixed voltage and 5 % for voltage range. For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum 2 %. All L-V5 achieve the standards and norms of the low voltage directive 72/23/EWG, V5 rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC) DIN EN 61000-0/-6/-4. * ** For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239). Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes. *** The quantities of operating liquid apply for fresh water operation without discharge liquid separator. For partial recirculation operation the quantity of the fresh applied refrigerant can be reduced by circulation of the operating liquid in a circuit (with discharge liqiud separator and internal recirculation of the operating liquid, available as accessories).
Other voltages2V5 131-.. ..- S 5 -.. 50 Hz 3~ 185220 V / 320380 V Y 220240 V / 345415 V Y 345415 V 500 V 3~ ATEX Category 2G 230 V / 400 V Y 400 V / 690 V Y 500 V D D D 1 6 5 200254 V / 345440 V Y 220275 V / 380480 V Y 380480 V 575 V H H H H 0 8 7 5 60 Hz
Quantity of Operating LiquidFrequency for fresh water operation at Inlet pressure *** m/h 1.8 1.8
Hz 50 60
DimensionsN1.0 N2.0 N3.0 N4.2 N8.7 Inlet flange Pressure flange Connection operating liquid Drain/Flushing Cavitation protectionN2.0 N8.7 N1.0 N3.0
N1.0, N2.0 N2.0 N8.7 N1.0 N3.0
N3.0 (nur only 2BV5 ...-0H.) N4.2 2BV5 ...-0K. N4.2 2BV5 ...-0H.
2V5 131 [mm]
a 801 s2 14
b 378 t 382
b1 300 v M40x1.5
b2 190 d1 19
c1 20 d2 182
c2 29 d3 142
h1 175 d4 114
h2 194 d5 67
h3 249 w 54
h4 427 w1 200
h5 372 w2 63
h6 53 w3 32
h7 76
h8 302
k 373
l 147
f 608 N4.2
g 291
n 103 N8.7 G8 x 11
s1 15 x 25
d1) (N1.0, N2.0) N3.0 2) DN65 / 2 G x 24
G8 x 25
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI 16.5-3-150 2) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI 16.5-1/2-150
Gardner Denver Deutschland GmbH
2
Techn. data sheet 2V5 131, edition 06/2005 En
Exploded drawing005 006
002 037 058 035 036 048 047 049 050 071 051
061 080 072
079
063 069 068
Materials of constructionPart- Designation No.002 005 006 035 036 037 047 048 049 050 051 058 061 063 068 069 071 072 079 080 Casing Pump shaft Feather key Mechanical seal Washer Set screw Impeller Tolerance ring for impeller Port plate Valve plate Intercepting plate Gasket for cover Cover Screw Plug screw Sealing ring Pipe of cavitation protection Washer for cavitation protection Plug screw Sealing ring
Material combination Grey cast iron/Grey cast iron/ronzeGrey cast iron (EN-GJL H 195 / EN-JL2030) EN 1561 Chrome steel (X20Cr13 / 1.4021) EN 10088 - 3 Chrome-nickel-molybdenum steel (X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3 SIC / Carbon / Viton (FPM) / Chrome-nickel-molybdenum steel (EN 12756 - Q1VGG) Chrome steel (X20Cr13 / 1.4021) EN 10088 - 3 Chrome-nickel-molybdenum steel (X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2 Cast aluminium bronze (G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982 Chrome-nickel steel (X12CrNi 17-7 / 1.4310) EN 10088 - 2 Grey cast iron (EN-GJL H 195 / EN-JL2030) EN 1561 Teflon (PTFE) Chrome-nickel-molybdenum steel (X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2 Nitrile-butadiene-caotchouc (NR 70) ISO 1629 Grey cast iron (EN-GJL H 195 / EN-JL2030) EN 1561 Steel (DIN ISO 8992) Machining steel, lead alloyed (11SMnPb30 / 1.0718) EN 10087 Teflon (PTFE) Teflon (PTFE) Chrome-nickel steel (X5CrNi 18-10 / 1.4301) EN 10088 - 3 Machining steel, lead alloyed (11SMnPb30 / 1.0718) EN 10087 Teflon (PTFE)
CrNi steel/CrNi steel/CrNi steelCast chrome-nickel-molybdenum steel (G-X5CrNiMoNb 18-10 / 1.4581) EN 10283 Chrome-nickel-molybdenum steel (X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3 Chrome-nickel-molybdenum steel (X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3 SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated / Chrome-nickel-molybdenum steel (EN 12756 - Q1M1GG) Chrome-nickel-molybdenum steel (X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3 Chrome-nickel-molybdenum steel (X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2 Cast chrome-nickel-molybdenum steel (G-X5CrNiMoNb 18-10 / 1.4581) EN 10283 Chrome-nickel steel (X12CrNi 17-7 / 1.4310) EN 10088 - 2 Cast chrome-nickel-molybdenum steel (G-X5CrNiMoNb 18-10 / 1.4581) EN 10283 Teflon (PTFE) Chrome-nickel-molybdenum steel (X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2 Silicone core, Teflon (PTFE) sheated Cast chrome-nickel-molybdenum steel (G-X5CrNiMoNb 18-10 / 1.4581) EN 10283 Steel (DIN ISO 8992) Chrome-nickel-molybdenum steel (X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3 Teflon (PTFE) Teflon (PTFE) Chrome-nickel steel (X5CrNi 18-10 / 1.4301) EN 10088 - 3 Chrome-nickel-molybdenum steel (X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3 Teflon (PTFE)
Gardner Denver Deutschland GmbH
3
Techn. data sheet 2V5 131, edition 06/2005 En
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.
Gardner Denver Schopfheim GmbH Elmo Rietschle is a brand of the Gardner Denver Blower Division [email protected] www.gd-elmorietschle.com Roggenbachstrae 58 79650 Schopfheim - Germany Tel.: +49 7622 392-0 Fax: +49 7622 392-300
Gardner Denver Deutschland GmbH Industriestrae 26 97616 ad Neustadt - Germany Tel.: +49 9771 6888-0 Fax: +49 9771 6888-4000